Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 253/778 | < Previous Page | 249 250 251 252 253 254 255 256 257 258 259 260  | Next Page >

• Share between Ubuntu machines

  - by Anero

  I'm sure it might be a very easy way to do this, but I haven't found how... I have two machines with Ubuntu 10.10 on the same network (just workgroup, no domain involved). On one of them I have shared a folder through Nautilus Folder Sharing. When opening the Network place on the second machine, I cannot see the first one listed, just Windows Network and when going into this folder I can see the Workgroup though when trying to go into it I get an Unable to mount. Failed to retrieve share list from server error. Is it required to do something else when sharing the folder through Nautilus?

  Read the article

• Sharing samba-folder with root access

  - by Industrial

  Hi everyone, I have a staging server in my network running Ubuntu server 10.10, being my main development area. As I need to access the files in the Apache root from other computers in the network, I have setup samba with the following settings: [www] comment = Apache root www path = /var/www writable = yes force user = root force group = root On the host computer, running Ubuntu 10.10 desktop, I am trying to mount the drive with a bash file looking like below: #!/bin/bash sudo mount -t cifs //192.168.1.5/www /media/www/ -o username=myusername,password=mypassword,rw,iocharset=utf8,file_mode=0777,dir_mode=0777 What happens is that I get mount error(13): Permission denied Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) thrown in my face whilst trying to execute the mount. I've done exactly the same, with exactly the same smb.conf & mount-bash file on another computer in my network, but this just wont work. What am I doing wrong? I am running out of ideas.

  Read the article

• dhcpd fails to start

  - by TECHPREACHER

  I recently installed Ubuntu 11.10 I then used apt-get to grab isc-dhcp3. I removed Network-Manager and manually configured my network interface eth0. In addition, I hand edited a dhcpd.conf file and designated eth0 as the listen port in /etc/default/isc-dhcp-server. However, each time I attempt to start dhcpd it fails. When I view the syslog file, the last line is as follows: "Not configured to listen on any interfaces!" My eth0 interface works fine. I can ping addresses inside and outside the network and perform DNS queries. Any help would be greatly appreciated. AJ

  Read the article

• VirtualBox: Import on different platform

  - by katsumii

  VirtualBox behaves almost the same on different OSes but the default network name for host-only network is different.The picture below is from Windows. On Linux, it will be named "vboxnet0" by default.This causes a problem on cross-platform export/import and it's already reported.#7067 (VERRINTERNALERROR: Inexistent host networking interface, named 'vboxnet0') – Oracle VM VirtualBoxVERR_INTERNAL_ERROR: Inexistent host networking interface, named 'vboxnet0'There are at least 2 workarounds.Open the imported VM in VBox GUI and pick correct network.Run CUI command like below. This one is for Windows.VBoxManage.exe modifyvm node1_1  --hostonlyadapter1 "VirtualBox Host-Only Ethernet Adapter"

  Read the article

• Passing data between engine layers

  - by spaceOwl

  I am building a software system (game engine with networking support ) that is made up of (roughly) these layers: Game Layer Messaging Layer Networking Layer Game related data is passed to the messaging layer (this could be anything that is game specific), where they are to be converted to network specific messages (which are then serialized to byte arrays). I'm looking for a way to be able to convert "game" data into "network" data, such that no strong coupling between these layers will exist. As it looks now, the Messaging layer sits between both layers (game and network) and "knows" both of them (it contains Converter objects that know how to translate between data objects of both layers back and forth). I am not sure this is the best solution. Is there a good design for passing objects between layers? I'd like to learn more about the different options.

  Read the article

• 12.04 in Virtualbox is keep losing my wireless connection

  - by Derek

  I've Windows 7 as the Host OS, Ubuntu 12.04 as the guest and a Netgear WG111v2 as the USB Wireless device. Its connected to an open Wi-Fi network at work to bypass my works crazy strict filtering, When on the domain. I currently have network eth0 turned off in the virtualbox settings so the only network source would be through the USB device at wlan1. Its odd but the wireless seems extremely temperamental, I constantly have to ifconfig wlan down then ifconfig wlan1 up to get it back online. I know this might be super vague just curious if anyone has tried something like this or run into anything like it to point me in a direction I might not be seeing.

  Read the article

• Cannot get Atheros AR9285 to work on 12.10

  - by user100449

  I've already went through all possible advices and still cannot start my Atheros AR9285 wireless card. I have a laptop Toshiba Portege Z830 where the WiFi already worked under Windows 7. But after migration on Ubuntu 12.10. I'm not able get it work. This is what I see on command lshw *-network UNCLAIMED description: Network controller product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:c0500000-c050ffff This is what I see on command rfkill list 0: Toshiba Bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 1: hci0: Bluetooth Soft blocked: yes Hard blocked: no Any idea?

  Read the article

• samba share not allowing windows pc to access

  - by user72289

  I have been trying to no avail, to share folders on my ubuntu pc with a windows network. The windows network isn't a homegroup, just a straight up access to folders made public. I can see the ubuntu shares I make, but when I try to access them I get a permission denied contact your system administrator type message. Could someone clarify the area re adding a user to samba, as there are about 30 different unix usernames! I just want my windows network to have unrestricted access to my linux folders. Any help would be greatly appreciated

  Read the article

• Sidestep Automatically Secures Your Mac’s Connection on Unsecure Networks

  - by Jason Fitzpatrick

  If you’re wary of browsing on wide open public Wi-Fi networks (and you should be), Sidestep is a free Mac application that routes your connection on an unsecure network through a secure proxy. Sidestep automatically detects when you are on an unprotected wireless network and forms an encrypted tunnel to the proxy you specified during setup. Anytime you login a wide open Wi-Fi node (such as at a coffee shop, airport, or other public area) you won’t be broadcasting your login credentials and other personal information in what amounts to plain text into the air around you. Anyone snooping on you or the network in general will simply see your stream of encrypted data going to the proxy. Hit up the link below to grab a copy and read additional information about setting up the program and finding/configuring a proxy server. Sidestep is freeware, Mac OS X only. Sidestep [via Gina Trapani] How to Create an Easy Pixel Art Avatar in Photoshop or GIMPInternet Explorer 9 Released: Here’s What You Need To KnowHTG Explains: How Does Email Work?

  Read the article

• Help me start my Atheros AR9285 working on Ubuntu 12.10

  - by user100449

  Could you, pls, help me with my wireless card Atheros AR9285 on Ubuntu 10.12.. I've already went through all possible advices and still cannot start my wireless card. I have a laptop Toshiba Portege Z830 where Wifi've already worked under Windows 7. But after migration on Ubuntu 10.12. I'm not able get it work. My actual situation is on image bellow This is what I see on command lshw *-network UNCLAIMED description: Network controller product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:c0500000-c050ffff This is what I see on command rfkill list 0: Toshiba Bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 1: hci0: Bluetooth Soft blocked: yes Hard blocked: no Any idea? Thank you Michal

  Read the article

• Broadcom bcm4313 Ubuntu 13.10 connection time out

  - by Wahtever

  After upgrading to Ubuntu 13.10 I keep getting connection timed out every few seconds at which point i have to disconnect and reconnect to the WiFi network. The WiFi card worked fine on 13.04 with the bcmwl-kernel-source installed but giving problems on 13.10: *-network description: Wireless interface product: BCM4313 802.11bgn Wireless Network Adapter vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: c0:14:3d:cc:c9:c7 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.4 latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f0500000-f0503fff How can i fix this? Thanks

  Read the article

• Putting Ubuntu Server on to a networked HDD

  - by SimplySimon

  Firstly, I know very little about servers and secondly the 1Tb HDD I have has network capabilities, but no software is installed on it, so when connected to the computer it is seen as a network connection, but not as a drive. Any advice on how to get started would be great. Up until now, I have been using it as a USB drive which worked well, but when this is sorted, I would like it to be connected directly to our BT HomeHub accessible through the WiFi for all the family to use as a film and back up repository. I would then be able to set up individual accounts for each family member to use and may be, if possible, make it accessible from outside locations. The First question then is: How can I install Ubuntu server on the 1Tb HDD attached directly to the computers network port but which doesn't show up in Nautilus? HDD Western Digital 1.0Tb LBA 1953525168 Model: WD10EACS-00DB0 DCM: DHRNHT2CF

  Read the article

• Wireless/Bluetooth problems on t43p

  - by user75965

  I have been struggling to get my wireless mini pcmcia card recognised by 12.04. It suddenly stopped, mid session. I have taken it out and replaced with a couple of spares with slightly different serial numbers. One had no joy - 'unauathorised'. The other worked briefly for thunderbird but not firefox, it seemed. The network controller reads like this: 0b:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05) I have ordered a replacement from ebay, and hope I got the right one - used the the FRU number from the one that stopped working. But I have ALWAYS had no joy with my Thinkpad t43p Bluetooth and Ubuntu ( 12.04, and even 11.04 and 11.10, if I remember rightly). Do you think the Bluetooth problem will solve with a new mini pcmcia? Surely not, as it has never worked, whereas Wireless worked until a couple of weeks ago...

  Read the article

• Slow writing HDD speed, Ubuntu 12.04 64-bit, Thinkpad T520i

  - by pyc

  It seems that (but I'm not completely sure), that when I'm copying files from gigabit network to HDD, I can't use full potential of the network which in my case is about 60 MB/s, because HDD writing is so slow like lower than 10 MB/s, and also it's slowing down the whole system which becomes pretty much unresponsive, almost impossible to work with. Copying files to samba share residing at Ubuntu machine, connected to share from Windows 7, I'm completely sure my network equipment is OK, and there's no CPU intensive process on Ubuntu except smbd getting about 10-20% from time to time which I think is OK. Something here is burried deep I think, maybe even in kernel. Already tried to switch from AHCI to compatibility mode, and turning acpi on and off - nothing helped. So it's like HDD buffer is full and emptying slowly while machine is sluggish, load is about 3 to 4. Somebody experienced the similar problems? Some help on troubleshooting process and identifying the cause would be helpful too :) Thanks!

  Read the article

• ubuntu will not connect after restart

  - by nicedoggy

  Firstly, I hope this hasn't been covered elsewhere, I have searched but haven't found this particular problem. I updated to 12.04 a while back and though I now thoroughly regret that decision, I'm able to live with 12.04 and all it's odd little quirks. The one problem that I would like to fix is this. I have a small network, using a router modem which stays on most of the time. If the computer is switched off, when it is switched on again I have to click on "auto Ethernet" in "Network" in order to get on the internet. It then works fine. Previous versions just connected automatically on restart. When 12.04 says it is unable to connect, other computers on the network are able to connect. Thanks for any help.

  Read the article

• Android - Multiplayer Game - Client / Server - Java etc

  - by user1405328

  I must write a multiplayer pong game for the school. Where are thousand of rooms and where two players can go in to a room and play together and collect points. I programmed the Pong game using Java (LibGDX). How can I do the Network part. I searched the web. And I came across Kryonet. Is there something better? What should I google. On the Internet there are a lot of those questions. And no good answers. I hope that this most questions can be answered. If someone has actual Open Source network game links, tutorials, books, network tutorial, etc. All this would help everyone. Thank you.

  Read the article

• USB modem dosn't working in Ubuntu

  - by skeeph

  In Ubuntu 12.10 USB-modem Huawei 171 from MTS is not connected to the network. First on the message "Are you registered on the network", immediately after that, "You are disconnected from the network." This happened after there was an internal error notification Ubuntu. I did not pay attention, and closed by sending the report. After the reboot does not work. Settings are not changed. I am online with this modem in Windows 8. Could you tell me why it is not working,please thank you in advance P.S Sorry for my English. It's foreign language for me. Please mention to me where are my mistakes. Thanks

  Read the article

• Need instructions on how to create wpa_supplicant.conf and add fast_reauth=0 to it

  - by nutty about natty

  Like many other natty users on a university/academic network, I'm experiencing annoying frequent disconnects/hangs/delays. See, for instance here. I would like to learn how to add fast_reauth=0 to the wpa_supplicant.conf file. This file, it seems, does not exit by default, and needs to be manually created first: README You will need to make a configuration file, e.g. /etc/wpa_supplicant.conf, with network configuration for the networks you are going to use. Further, I installed wpa_gui which probably needs to be launched with parameters, else it's pretty blank... What I'm hoping for is this: That creating a wpa_supplicant.conf file with fast_reauth=0 in it, saving it to the relevant path, will work and make my uni wireless (more or even completely) stable. I read mixed reviews about wicd (as an alternative to the network manager). Also note that on my basic wlan at home (with bog-standard wpa encryption) the connection is stable. Thanks!

  Read the article

• Connect to a VPN from a Virtual Machine

  - by kaharas

  I am running an Ubuntu ditro inside a VMWare virtual machine with a bridged connection on a windows 7 host. What I am trying to do is to have the virtual machine connect to a VPN, but I'm not having much success. At first, the system was using wicd, but I replaced it with network-manager who's supposed to have OpenVPN support. The problem is, even tho i've purged the wicd installation, there're connections shown in the network manager, and still, I'm able to access the net. I've also added the openvpn data in the network manager tab, but it's shown as never used. PS: when I try to stop and start the NetworkManager service, an error message pops up telling me that there's not such a service, but apt-get tells me i've already installed it...

  Read the article

• How to copy the file from source to destination only once at a time?

  - by Viswa

  I have to copy the file from my desktop to my mounted directory. I was using the following command to copy the file from my desktop to mounted directory. os.system("cp -f /home/Desktop/filename /media/folder_1"). It works fine. But the problem is while copying the file from my source to mounted directory(folder_1) if any interruption is happens like network down, then the system continuously keep on trying. It couldn't skip that process. Finally, when the network comes the files are again copy to my mounted directory. Due to this continuous trying, next time i try to move the content it throws "permission denied" error. How do i copy the file only once, if any network issues happen then it will not keep try to copy, instead of that, it throws the error. If you know, Let me. Its very useful to me.

  Read the article

• How to define default gateway with multiple DHCP interfaces?

  - by DrumEater

  How does ifconfig determine which network interface to use as the default when DHCP assigns a default route for each NIC? It seems like it's in a race-condition and I need to have a more reliable solution. Is there a setting in /etc/network/interfaces that could define the preferred gateway? I read about "metric" but that did not seem to function. 10.04 LTS Server with two NICs on a managed network. IP addresses are assigned via DHCP which I do not manage. eth0 is assigned a private NAT address; eth1 is assigned a public IP.

  Read the article

• Ubuntu 12.10 hasa no wireless connectivity on Dell Inspiron 1520

  - by Jorge Tijerina

  I have just installed Ubuntu for the first time ever. I have just installed it in a Dell Inspiron 1520 that came pre installed with Windows Vista and i currently run both of the OS (I just choose when the computer starts up). The wifi definitely works on the computer since i used it to download Ubuntu in the first place when I was using Vista. The Network Manager says that I only have a 'Wired' Network and it doesn't have any other options to choose from. I connected the Laptop into a wired connection and downloaded the 'Wicd Network Manager' but it had no effect either. From there I continued to go into 'Software Sources' and installed the wireless drive but that had no effect either. So... What can I do?

  Read the article

• help me about install ubuntu server 12.04 on vmware

  - by zohreh

  I want to install Ubuntu server 64-bit on vmware 8.0.2 but I face with a problem ! I don't know why ! the problem is: From here you can choose to retry DHCP network autoconfiguration (which may succeed if your DHCP server takes a long time to respond) or to configure the network manually. Some DHCP servers require a DHCP hostname to be sent by the client, so you can also choose to retry DHCP network autoconfiguration with a hostname that you provide. there are 4 option for Continuation i don't know exactly to select which option also what is The cause of the problem? thanks a lot

  Read the article

• Create a HotSpot which requires a username and password

  - by Trumbun

  I wish to set up a wireless access point which requires a username and password in order for clients to use the internet. The network setup will be internet modem connected to an Ubuntu Server (2 networks cards). The first network cards to get the internet to the server and the second network card to connect the the wifi hotspot. The server will host the software such as (Example software for windows) which will control the user connected by forcing them to login with the credentials given at the reception. Can some suggest some software that I can use? Thanks in advance

  Read the article

• Is the upgrade server working? Im upgrading from 8.10 to 9.04 [closed]

  - by jarod

  Possible Duplicate: How to install software or upgrade from old unsupported release? Is the upgrade server working? Im upgrading from 8.10 to 9.04 and it says "extracting the upgrade failed there may be a problem with the network or the server." Also when I hit check it says "Could not download all repository indexes The repository may no longer be available or could not be contacted because of network problems. If available an older version of the failed index will be used. Otherwise the repository will be ignored. Check your network connection and ensure the repository address in the preferences is correct." and Failed to fetch http://security.ubuntu.com/ubuntu/dists/intrepid-security/main/binary-i386/Packages.gz 404 Not Found [IP: 91.189.92.184 80] and then a bunch more failed to fetch

  Read the article

< Previous Page | 249 250 251 252 253 254 255 256 257 258 259 260  | Next Page >