Search Results

Search found 6683 results on 268 pages for 'ole media'.

Page 254/268 | < Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >

• Exposing the AnyConnect HTTPS service to outside network

  - by Maciej Swic

  We have a Cisco ASA 5505 with firmware ASA9.0(1) and ASDM 7.0(2). It is configured with a public ip address, and when trying to reach it from the outside by HTTPS for AnyConnect VPN, we get the following log output: 6 Nov 12 2012 07:01:40 <client-ip> 51000 <asa-ip> 443 Built inbound TCP connection 2889 for outside:<client-ip>/51000 (<client-ip>/51000) to identity:<asa-ip>/443 (<asa-ip>/443) 6 Nov 12 2012 07:01:40 <client-ip> 50999 <asa-ip> 443 Built inbound TCP connection 2890 for outside:<client-ip>/50999 (<client-ip>/50999) to identity:<asa-ip>/443 (<asa-ip>/443) 6 Nov 12 2012 07:01:40 <client-ip> 51000 <asa-ip> 443 Teardown TCP connection 2889 for outside:<client-ip>/51000 to identity:<asa-ip>/443 duration 0:00:00 bytes 0 No valid adjacency 6 Nov 12 2012 07:01:40 <client-ip> 50999 <asa-ip> 443 Teardown TCP connection 2890 for outside:<client-ip>/50999 to identity:<asa-ip>/443 duration 0:00:00 bytes 0 No valid adjacency We finished the startup wizard and the anyconnect vpn wizard and here is the resulting configuration: Cryptochecksum: 12262d68 23b0d136 bb55644a 9c08f86b : Saved : Written by enable_15 at 07:08:30.519 UTC Mon Nov 12 2012 ! ASA Version 9.0(1) ! hostname vpn domain-name office.<redacted>.com enable password <redacted> encrypted passwd <redacted> encrypted names ip local pool vpn-pool 192.168.67.2-192.168.67.253 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.68.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address <redacted> 255.255.255.248 ! ftp mode passive dns server-group DefaultDNS domain-name office.<redacted>.com object network obj_any subnet 0.0.0.0 0.0.0.0 pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu inside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected ! object network obj_any nat (inside,outside) dynamic interface timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL http server enable http 192.168.68.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto ca trustpoint _SmartCallHome_ServerCA crl configure crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=vpn proxy-ldc-issuer crl configure crypto ca trustpool policy crypto ca certificate chain _SmartCallHome_ServerCA certificate ca 6ecc7aa5a7032009b8cebcf4e952d491 <redacted> quit crypto ca certificate chain ASDM_TrustPoint0 certificate f678a050 <redacted> quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable outside client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 ssh 192.168.68.0 255.255.255.0 inside ssh timeout 5 console timeout 0 vpn-addr-assign local reuse-delay 60 dhcpd auto_config outside ! dhcpd address 192.168.68.254-192.168.68.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ssl trust-point ASDM_TrustPoint0 inside ssl trust-point ASDM_TrustPoint0 outside webvpn enable outside enable inside anyconnect image disk0:/anyconnect-win-3.1.01065-k9.pkg 1 anyconnect image disk0:/anyconnect-linux-3.1.01065-k9.pkg 2 anyconnect image disk0:/anyconnect-macosx-i386-3.1.01065-k9.pkg 3 anyconnect profiles GM-AnyConnect_client_profile disk0:/GM-AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy GroupPolicy_GM-AnyConnect internal group-policy GroupPolicy_GM-AnyConnect attributes wins-server none dns-server value 192.168.68.254 vpn-tunnel-protocol ikev2 ssl-client default-domain value office.<redacted>.com webvpn anyconnect profiles value GM-AnyConnect_client_profile type user username <redacted> password <redacted> encrypted tunnel-group GM-AnyConnect type remote-access tunnel-group GM-AnyConnect general-attributes address-pool vpn-pool default-group-policy GroupPolicy_GM-AnyConnect tunnel-group GM-AnyConnect webvpn-attributes group-alias GM-AnyConnect enable ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context call-home reporting anonymous Cryptochecksum:12262d6823b0d136bb55644a9c08f86b : end Clearly we are missing something, but the question is, what?

  Read the article

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• Three ways to upload/post/convert iMovie to YouTube [closed]

  - by alexyu2010

  For Mac users, iMovie is probably a convenient tool for making, editing their own home movies so as to upload to YouTube for sharing with more people. However, uploading iMovie files to YouTube can't be always a smooth run, I did notice many people complaining about it. This article is delivered for guiding those who are haunted by the nightmare by providing three common ways to upload iMovie files to YouTube. YouTube and iMovie YouTube is the most popular video sharing website for users to upload, share and view videos. It empowers anyone with an Internet connection the ability to upload video clips and share them with friends, family and the world. Users are invited to leave comments, pick favourites, send messages to each other and watch videos sorted into subjects and channels. YouTube accepts videos uploaded in most container formats, including WMV (Windows Media Video), 3GP (Cell Phones), AVI (Windows), MOV (Mac), MP4 (iPod/PSP), FLV (Adobe Flash), MKV (H.264). These include video codecs such as MP4, MPEG and WMV. iMovie is a common video editing software application comes with every Mac for users to edit their own home movies. It imports video footage to the Mac using either the Firewire interface on most MiniDV format digital video cameras, the USB port, or by importing the files from a hard drive where users can edit the video clips, add titles, and add music. Since 1999, eight versions of iMovie have been released by Apple, each with its own functions and characteristic, and each of them deal with videos in a way more or less different. But the most common formats handled with iMovie if specialty discarded as far as to my research are MOV, DV, HDV, MPEG-4. Three ways for successful upload iMovie files to YouTube Solution one and solution two suitable for those who are 100 certainty with their iMovie files which are fully compatible with YouTube. For smooth uploading, you are required to get a YouTube account first. Solution 1: Directly upload iMovie to YouTube Step 1: Launch iMovie, select the project you want to upload in YouTube. Step 2: Go to the file menu, click Share, select Export Movie Step 3: Specify the output file name and directory and then type the video type and video size. Solution 2: Post iMovie to YouTube straightly Step 1: Launch iMovie, choose the project you want to post in YouTube Step 2: From the Share menu, choose YouTube Step 3: In the pop-up YouTube windows, specify the name of your YouTube account, the password, choose the Category and fill in the description and tags of the project. Tick Make this movie more private on the bottom of the window, if possible, to limit those who can view the project. Click Next, and then click Publish. iMovie will automatically export and upload the movie to YouTube. Step 4: Click Tell a Friend to email friends and your family about your film. You are also allowed to copy the URL from Tell a Friend window and paste it into an email you created in your favourite email application if you like. Anyone you send to email to will be able to follow the URL directly to your movie. Note: Videos uploaded to YouTube are limited to ten minutes in length and a file size of 2GB. Solution 3: Upload to iMovie after conversion If neither of the above mentioned method works, there is still a third way to turn to. Sometimes, your iMovie files may not be recognized by YouTube due to the versions of iMovie (settings and functions may varies among versions), video itself (video format difference because of file extension, resolution, video size and length), compatibility (videos that are completely incompatible with YouTube). In this circumstance, the best and reliable method is to convert your iMovie files to YouTube accepted files, iMovie to YouTube converter will be inevitably the ideal choice. iMovie to YouTube converter is an elaborately designed tool for convert iMovie files to YouTube workable WMV, 3GP, AVI, MOV, MP4, FLV, MKV for smooth uploading with hard-to-believe conversion speed and second to none output quality. It can also convert between almost all popular popular file formats like AVI, WMV, MPG, MOV, VOB, DV, MP4, FLV, 3GP, RM, ASF, SWF, MP3, AAC, AC3, AIFF, AMR, WAV, WMA etc so as to put on various portable devices, import to video editing software or play on vast amount video players. iMovie to YouTube converter can also served as an excellent video editing tool to meet your specific program requirements. For example, you can cut your video files to a certain length, or split your video files to smaller ones and select the proper resolution suitable for demands of YouTube by Clip or Settings separately. Crop allows you to cut off unwanted black edges from your videos. Besides, you can also have a good command of the whole process or snapshot your favourite pictures from the preview window. More can be expected if you have a try.

  Read the article

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• Internet Explorer percent based layout issue

  - by Tom

  Heya, My goal is to make a layout that is 200% width and height, with four containers of equal height and width (100% each), using no javascript as the bear minimum (or preferably no hacks). Right now I am using HTML5, and CSS display:table. It works fine in Safari 4, Firefox 3.5, and Chrome 5. I haven't tested it yet on older versions. Nonetheless, in IE7 and IE8 this layout fails completely. (I do use the Javascript HTML5 enabling script /cc../, so it should not be the use of new HTML5 tags) Here is what I have: <!DOCTYPE html> <html> <head> <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> <meta charset="UTF-8" /> <title>IE issue with layout</title> <style type="text/css" media="all"> /* styles */ @import url("reset.css"); /* Generall CSS */ .table { display:table; } .row { display:table-row; } .cell { display:table-cell; } /* Specific CSS */ html, body { //overflow:hidden; I later intend to limit the viewport } section#body { position:absolute; width:200%; height:200%; overflow:hidden; } section#body .row { width:200%; height:50%; overflow:hidden; } section#body .row .cell { width:50%; overflow:hidden; } section#body .row .cell section { display:block; width:100%; height:100%; overflow:hidden; } section#body #stage0 section header { text-align:center; height:20%; display:block; } section#body #stage0 section footer { display:block; height:80%; } </style> </head> <body> <section id="body" class="table"> <section class="row"> <section id="stage0" class="cell"> <section> <header> <form> <input type="text" name="q" /> <input type="submit" value="Search" /> </form> </header> <footer> <table id="scrollers"> </table> </footer> </section> </section> <section id="stage1" class="cell"> <section> content </section> </section> </section> <section class="row"> <section id="stage2" class="cell"> <section> content </section> </section> <section id="stage3" class="cell"> <section> content </section> </section> </section> </section> </body> </html> You can see it live here: http://www.tombarrasso.com/ie-issue/

  Read the article

• Add note model in Rails

  - by dannymcc

  Hi Everyone, I am following the 15 minute blog tutorial on Ruby on Rails .com: http://media.rubyonrails.org/video/rails_blog_2.mov and am stumbling into some issues. I am using the following alterations to the names in the tutorial: posts = kases comments = notes I have setup the models as follows: class Kase < ActiveRecord::Base validates_presence_of :jobno has_many :notes belongs_to :company # foreign key: company_id belongs_to :person # foreign key in join table belongs_to :surveyor, :class_name => "Company", :foreign_key => "appointedsurveyor_id" belongs_to :surveyorperson, :class_name => "Person", :foreign_key => "surveyorperson_id" def to_param jobno end and... class Note < ActiveRecord::Base belongs_to :kase end The Notes controller look like this: # POST /notes # POST /notes.xml def create @kase = Kase.find(params[:kase_id]) @note = @kase.notes.build(params[:note]) redirect_to @kase end and the database scheme for Kases looks like this: create_table "notes", :force => true do |t| t.integer "kase_id" t.text "body" t.datetime "created_at" t.datetime "updated_at" end and for kases... create_table "kases", :force => true do |t| t.string "jobno" t.date "dateinstructed" t.string "clientref" t.string "clientcompanyname" t.text "clientcompanyaddress" t.string "clientcompanyfax" t.string "casehandlername" t.string "casehandlertel" t.string "casehandleremail" t.text "casesubject" t.string "transport" t.string "goods" t.string "claimantname" t.string "claimantaddressline1" t.string "claimantaddressline2" t.string "claimantaddressline3" t.string "claimantaddresscity" t.string "claimantaddresspostcode" t.string "claimantcontact" t.string "claimanttel" t.string "claimantmob" t.string "claimantemail" t.string "claimanturl" t.string "lyingatlocationname" t.string "lyingatlocationaddressline1" t.string "lyingatlocationaddressline2" t.string "lyingatlocationaddressline3" t.string "lyingatlocationaddresscity" t.string "lyingatlocationaddresspostcode" t.string "lyingatlocationcontactname" t.string "lyingattel" t.string "lyingatmobile" t.string "lyingatlocationurl" t.text "comments" t.string "invoicenumber" t.string "netamount" t.string "vat" t.string "grossamount" t.date "dateclosed" t.date "datepaid" t.datetime "filecreated" t.string "avatar_file_name" t.string "avatar_content_type" t.integer "avatar_file_size" t.datetime "avatar_updated_at" t.datetime "created_at" t.datetime "updated_at" t.string "kase_status" t.string "invoice_date" t.integer "surveyorperson_id" t.integer "appointedsurveyor_id" t.integer "person_id" t.string "company_id" t.string "dischargeamount" t.string "dishchargeheader" t.text "highrisesubject" end Whenever I enter a note into the kase show view's note entry form: <h2>Notes</h2> <div id="sub-notes"> <%= render :partial => @kase.notes %> </div> <% form_for [@kase, Note.new] do |f| %> <p> <%= f.label :body, "New Note" %><br /> <%= f.text_area :body %> </p> <p><%= f.submit "Add Note" %></p> <% end %> partial: <% div_for note do %> <p> <strong>Created <%= time_ago_in_words(note.created_at) %> ago</strong><br /> <%= h(note.body) %> </p> <% end %> I get the following error: ActiveRecord::RecordNotFound in NotesController#create Couldn't find Kase with ID=Test Case I have tried removing the def to_param jobno end from the kase model, but the same error shows. Any ideas what I'm missing? Thanks, Danny

  Read the article

• How to associate newly created SurfaceHolder to MediaPlayer

  - by fayerth

  In my code, I want to be able to temporarily hide (and subsequently show) a video. I am using a SurfaceView + MediaPlayer combination instead of the VideoView due to requirements. However, I am facing difficulties in getting video playback to occur as expected after I show the SurfaceView. My code excerpts includes the following: public void show() { if (mSurface != null) mSurface.setVisibility(View.VISIBLE); } public void hide() { if (mSurface != null) { if (isInPlaybackState()) pause(); mSurface.setVisibility(View.INVISIBLE); } } @Override public void surfaceCreated(final SurfaceHolder holder) { mHolder = holder; openVideo(); } @Override public void surfaceDestroyed(final SurfaceHolder holder) { // After this, the surface can't be used again mHolder = null; } private void openVideo() { if (mAssetPath == null || !mAssetPath.isEmpty() || mHolder == null) { // Not ready yet; try again later return; } // Pause music playback service Intent i = new Intent("com.android.music.musicservicecommand"); i.putExtra("command", "pause"); getActivity().sendBroadcast(i); if (mPlayer == null) { initializePlayer(); } else { mPlayer.setDisplay(mHolder); } } Based on the above, when I call hide(), surfaceDestroyed(SurfaceHolder) gets triggered. When I later call show(), surfaceCreated(SurfaceHolder) gets triggered, which will call openVideo() and associate the player with the newly provided SurfaceHolder. The above works as expected, and I believe this should be the correct process; however, when I call mPlayer.start(), I would hear the video's audio playing without any video and see the following error messages (which eventually causes the media playback to stop and complete, as noted by the disconnect logs): 10-23 11:29:42.775: E/MediaPlayer(4204): Error (1,-2147483648) 10-23 11:29:42.795: E/MediaPlayer(4204): Error (-38,0) 10-23 11:29:42.805: E/MediaPlayer(4204): Error (1,-2147483648) 10-23 11:29:42.810: V/MediaPlayer(4204): message received msg=100, ext1=1, ext2=-2147483648 10-23 11:29:42.810: E/MediaPlayer(4204): error (1, -2147483648) 10-23 11:29:42.810: V/MediaPlayer(4204): callback application 10-23 11:29:42.810: V/MediaPlayer(4204): back from callback 10-23 11:29:42.825: E/MediaPlayer(4204): Error (1,-2147483648) 10-23 11:29:42.850: V/MediaPlayer-JNI(4204): getCurrentPosition: 671668 (msec) 10-23 11:29:42.850: V/MediaPlayer-JNI(4204): getCurrentPosition: 671668 (msec) 10-23 11:29:42.850: V/MediaPlayer(4204): message received msg=100, ext1=1, ext2=-2147483648 10-23 11:29:42.850: E/MediaPlayer(4204): error (1, -2147483648) 10-23 11:29:42.850: V/MediaPlayer(4204): callback application 10-23 11:29:42.850: V/MediaPlayer(4204): back from callback 10-23 11:29:42.875: V/MediaPlayer-JNI(4204): stop 10-23 11:29:42.875: V/MediaPlayer(4204): stop 10-23 11:29:42.875: E/MediaPlayer(4204): stop called in state 0 10-23 11:29:42.875: V/MediaPlayer(4204): message received msg=100, ext1=-38, ext2=0 10-23 11:29:42.875: E/MediaPlayer(4204): error (-38, 0) 10-23 11:29:42.875: V/MediaPlayer(4204): callback application 10-23 11:29:42.875: V/MediaPlayer(4204): back from callback 10-23 11:29:42.875: V/MediaPlayer-JNI(4204): reset 10-23 11:29:42.875: V/MediaPlayer(4204): reset 10-23 11:29:42.900: V/MediaPlayer-JNI(4204): release 10-23 11:29:42.900: V/MediaPlayer(4204): setListener 10-23 11:29:42.900: V/MediaPlayer(4204): disconnect 10-23 11:29:42.910: V/MediaPlayer(4204): destructor 10-23 11:29:42.910: V/MediaPlayer(4204): disconnect Has anyone encountered this issue before and found a workaround? Or would the only option be to create a new MediaPlayer as well?

  Read the article

• Blend Interaction Behaviour gives "points to immutable instance" error

  - by kennethkryger

  I have a UserControl that is a base class for other user controls, that are shown in "modal view". I want to have all user controls fading in, when shown and fading out when closed. I also want a behavior, so that the user can move the controls around.My contructor looks like this: var tg = new TransformGroup(); tg.Children.Add(new ScaleTransform()); RenderTransform = tg; var behaviors = Interaction.GetBehaviors(this); behaviors.Add(new TranslateZoomRotateBehavior()); Loaded += ModalDialogBase_Loaded; And the ModalDialogBase_Loaded method looks like this: private void ModalDialogBase_Loaded(object sender, RoutedEventArgs e) { var fadeInStoryboard = (Storyboard)TryFindResource("modalDialogFadeIn"); fadeInStoryboard.Begin(this); } When I press a Close-button on the control this method is called: protected virtual void Close() { var fadeOutStoryboard = (Storyboard)TryFindResource("modalDialogFadeOut"); fadeOutStoryboard = fadeOutStoryboard.Clone(); fadeOutStoryboard.Completed += delegate { RaiseEvent(new RoutedEventArgs(ClosedEvent)); }; fadeOutStoryboard.Begin(this); } The storyboard for fading out look like this: <Storyboard x:Key="modalDialogFadeOut"> <DoubleAnimationUsingKeyFrames Storyboard.TargetProperty="(UIElement.RenderTransform).(TransformGroup.Children)[0].(ScaleTransform.ScaleX)" Storyboard.TargetName="{x:Null}"> <EasingDoubleKeyFrame KeyTime="0" Value="1"> <EasingDoubleKeyFrame.EasingFunction> <BackEase EasingMode="EaseIn" Amplitude="0.3" /> </EasingDoubleKeyFrame.EasingFunction> </EasingDoubleKeyFrame> <EasingDoubleKeyFrame KeyTime="0:0:0.4" Value="0"> <EasingDoubleKeyFrame.EasingFunction> <BackEase EasingMode="EaseIn" Amplitude="0.3" /> </EasingDoubleKeyFrame.EasingFunction> </EasingDoubleKeyFrame> </DoubleAnimationUsingKeyFrames> <DoubleAnimationUsingKeyFrames Storyboard.TargetProperty="(UIElement.RenderTransform).(TransformGroup.Children)[0].(ScaleTransform.ScaleY)" Storyboard.TargetName="{x:Null}"> <EasingDoubleKeyFrame KeyTime="0" Value="1"> <EasingDoubleKeyFrame.EasingFunction> <BackEase EasingMode="EaseIn" Amplitude="0.3" /> </EasingDoubleKeyFrame.EasingFunction> </EasingDoubleKeyFrame> <EasingDoubleKeyFrame KeyTime="0:0:0.4" Value="0"> <EasingDoubleKeyFrame.EasingFunction> <BackEase EasingMode="EaseIn" Amplitude="0.3" /> </EasingDoubleKeyFrame.EasingFunction> </EasingDoubleKeyFrame> </DoubleAnimationUsingKeyFrames> <DoubleAnimationUsingKeyFrames Storyboard.TargetProperty="(UIElement.Opacity)" Storyboard.TargetName="{x:Null}"> <EasingDoubleKeyFrame KeyTime="0" Value="1" /> <EasingDoubleKeyFrame KeyTime="0:0:0.3" Value="0" /> <EasingDoubleKeyFrame KeyTime="0:0:0.4" Value="0" /> </DoubleAnimationUsingKeyFrames> </Storyboard> If the user control is show, and the user does NOT move it around on the screen, everything works fine. However, if the user DOES move the control around, I get the following error when the modalDialogFadeOut storyboard is started: 'Children' property value in the path '(0).(1)[0].(2)' points to immutable instance of 'System.Windows.Media.TransformCollection'. How can fix this?

  Read the article

• Need suggestions on how to extract data from .docx/.doc file then into mssql

  - by DarkPP

  I'm suppose to develop an automated application for my project, it will load past-year examination/exercises paper (word file), detect the sections accordingly, extract the questions and images in that section, and then store the questions and images into the database. (Preview of the question paper is at the bottom of this post) So I need some suggestions on how to extract data from a word file, then inserting them into a database. Currently I have a few methods to do so, however I have no idea how I could implement them when the file contains textboxes with background image. The question has to link with the image. Method One (Make use of ms office interop) Load the word file - Extract image, save into a folder - Extract text, save as .txt - Extract text from .txt then store in db Question: How i detect the section and question. How I link the image to the question. Extract text from word file (Working): private object missing = Type.Missing; private object sFilename = @"C:\temp\questionpaper.docx"; private object sFilename2 = @"C:\temp\temp.txt"; private object readOnly = true; object fileFormat = Word.WdSaveFormat.wdFormatText; private void button1_Click(object sender, EventArgs e) { Word.Application wWordApp = new Word.Application(); wWordApp.DisplayAlerts = Word.WdAlertLevel.wdAlertsNone; Word.Document dFile = wWordApp.Documents.Open(ref sFilename, ref missing, ref readOnly, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing); dFile.SaveAs(ref sFilename2, ref fileFormat, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing,ref missing, ref missing,ref missing,ref missing,ref missing,ref missing, ref missing,ref missing); dFile.Close(ref missing, ref missing, ref missing); } Extract image from word file (Doesn't work on image inside textbox): private Word.Application wWordApp; private int m_i; private object missing = Type.Missing; private object filename = @"C:\temp\questionpaper.docx"; private object readOnly = true; private void CopyFromClipbordInlineShape(String imageIndex) { Word.InlineShape inlineShape = wWordApp.ActiveDocument.InlineShapes[m_i]; inlineShape.Select(); wWordApp.Selection.Copy(); Computer computer = new Computer(); if (computer.Clipboard.GetDataObject() != null) { System.Windows.Forms.IDataObject data = computer.Clipboard.GetDataObject(); if (data.GetDataPresent(System.Windows.Forms.DataFormats.Bitmap)) { Image image = (Image)data.GetData(System.Windows.Forms.DataFormats.Bitmap, true); image.Save("C:\\temp\\DoCremoveImage" + imageIndex + ".png", System.Drawing.Imaging.ImageFormat.Png); } } } private void button1_Click(object sender, EventArgs e) { wWordApp = new Word.Application(); wWordApp.Documents.Open(ref filename, ref missing, ref readOnly, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing, ref missing); try { for (int i = 1; i <= wWordApp.ActiveDocument.InlineShapes.Count; i++) { m_i = i; CopyFromClipbordInlineShape(Convert.ToString(i)); } } finally { object save = false; wWordApp.Quit(ref save, ref missing, ref missing); wWordApp = null; } } Method Two Unzip the word file (.docx) - Copy the media(image) folder, store somewhere - Parse the XML file - Store the text in db Any suggestion/help would be greatly appreciated :D Preview of the word file: (backup link: http://i.stack.imgur.com/YF1Ap.png)

  Read the article

• set all nested li's to be width of widest li

  - by unhitched

  hey, How do I make nested li's the same width? When I use the below code each nested li is only as wide as it's text + margin. I'd like all of the li's to be as wide as the widest li under the parent ul. eg: <ul id="menu"> <li <a href="#" title="Menu a">Menu a</a></li> <li <a href="#" title="Menu b">Menu b</a></li> <li <a href="#" title="Nested Menu">Nested Menu</a> <ul> <li <a href="#" title="Menu Item">Menu Item</li> <li <a href="#" title="Long Menu Item">Long Menu Item</a></li> <li <a href="#" title="Longer Menu Item">Longer Menu Item</a></li> </ul> </li> <li <a href="#" title="Menu z">Menu z</a></li> </ul> with css: <style type="text/css" media="all"> * { padding:0; margin:0; } body, html { width: 100%; height: 100%; } #wrapper { width: 800px; height: 100%; margin: auto; } #menu { margin: 0 0 0 8px; padding: 0; font-size: 14px; font-weight: normal; } #menu ul { list-style-type:none; list-style-position:outside; position:relative; z-index:300; height: 32px; font-weight:bold; white-space: nowrap; padding:0; } #menu a {text-decoration:none; line-height: 32px; } #menu a:hover { } #menu li { float:left; position:relative; display: inline; height: 100%; list-style-type: none; padding: 0 20px; background: #ccc; } #menu ul { position:absolute; display:none; left:0px; background: #BDCCD4; width:100%; } #menu ul a, #menu li a { display: block; } #menu li ul { background: #BDCCD4; display:block; } #menu li ul a { font-weight: normal; height:auto; float:left; } #menu ul ul { padding: 0 9px; display:block; } #menu li ul li { padding: 0 9px; background: #BDCCD4; } #menu li:hover { background: #ddd; height: 32px; } #menu li li:hover, #menu li li li:hover { background: #ddd; height: 32px; } #menu li a:link, #menu li a:visited { text-decoration: none; color: #003E7E; margin: auto; }

  Read the article

• Themes outside application.

  - by Marek

  Hi all I read http://forum.kohanaframework.org/comments.php?DiscussionID=5744&page=1#Item_0 and I want to use similar solution, but with db. In my site controller after(): $theme = $page->get_theme_name(); //Orange Kohana::set_module_path('themes', Kohana::get_module_path('themes').'/'.$theme); $this->template = View::factory('layout') I checked with firebug: fire::log(Kohana::get_module_path('themes')); // D:\tools\xampp\htdocs\kohana\themes/Orange I am sure that path exists. I have directly in 'Orange' folder 'views' folder with layout.php file. But I am getting: The requested view layout could not be found Extended Kohana_Core is just: public static function get_module_path($module_key) { return self::$_modules[$module_key]; } public static function set_module_path($module_key, $path) { self::$_modules[$module_key] = $path; } Could anybody help me with solving that issue? Maybe it is a .htaccess problem: # Turn on URL rewriting RewriteEngine On # Put your installation directory here: # If your URL is www.example.com/kohana/, use /kohana/ # If your URL is www.example.com/, use / RewriteBase /kohana/ # Protect application and system files from being viewed RewriteCond $1 ^(application|system|modules) # Rewrite to index.php/access_denied/URL RewriteRule ^(.*)$ / [PT,L] RewriteRule ^(media) - [PT,L] RewriteRule ^(themes) - [PT,L] # Allow these directories and files to be displayed directly: # - index.php (DO NOT FORGET THIS!) # - robots.txt # - favicon.ico # - Any file inside of the images/, js/, or css/ directories RewriteCond $1 ^(index\.php|robots\.txt|favicon\.ico|static) # No rewriting RewriteRule ^(.*)$ - [PT,L] # Rewrite all other URLs to index.php/URL RewriteRule ^(.*)$ index.php/$1 [PT,L] Could somebody help? What I am doing wrong? Regards [EDIT] My controller code: class Controller_Site extends Controller_Fly { public static $meta_names = array('keywords', 'descriptions', 'author'); public function action_main() { $this->m('page')->get_main_page(); } public function action_page($page_title) { $this->m('page')->get_by_link($page_title); } public function after() { $page = $this->m('page'); $metas = ''; foreach(self::$meta_names as $meta) { if (! empty($page->$meta)) { $metas .= html::meta($page->$meta, $meta).PHP_EOL; } } $theme = $page->get_theme_name(); Kohana::set_module_path('themes', Kohana::get_module_path('themes').'/'.$theme); $menus = $page->get_menus(); $this->template = View::factory('layout') ->set('theme', $theme) ->set('metas', $metas) ->set('menus', $menus['content']) ->set('sections', $page->get_sections()) ->set_global('page', $page); if ($page->header_on) { $settings = $this->m('setting'); $this->template->header = View::factory('/header') ->set('title', $settings->title) ->set('subtitle', $settings->subtitle) ->set('menus', $menus['header']); } if ($page->sidebar_on) { $this->template->sidebar = View::factory('sidebar', array('menus' => $menus['sidebar'])); } if ($page->footer_on) { $this->template->footer = View::factory('footer'); } parent::after(); } } and parent controller: abstract class Controller_Fly extends Controller_Template { protected function m($model_name, $id = NULL) { if (! isset($this->$model_name)) { $this->$model_name = ORM::factory($model_name, $id); } return $this->$model_name; } protected function mf($model_name, $id = NULL) { return ORM::factory($model_name, $id); } }

  Read the article

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• Google Analytics V2 SDK for Android EasyTracker giving errors

  - by Prince

  I have followed the tutorial for the new Google Analytics V2 SDK for Android located here: https://developers.google.com/analytics/devguides/collection/android/v2/ Unfortunately whenever I go to run the application the reporting is not working and this is the messages that logcat gives me: 07-09 09:13:16.978: W/Ads(13933): No Google Analytics: Library Incompatible. 07-09 09:13:16.994: I/Ads(13933): To get test ads on this device, call adRequest.addTestDevice("2BB916E1BD6BE6407582A429D763EC71"); 07-09 09:13:17.018: I/Ads(13933): adRequestUrlHtml: <html><head><script src="http://media.admob.com/sdk-core-v40.js"></script><script>AFMA_getSdkConstants();AFMA_buildAdURL({"kw":[],"preqs":0,"session_id":"7925570029955749351","u_sd":2,"seq_num":"1","slotname":"a14fd91432961bd","u_w":360,"msid":"com.mysampleapp.sampleapp","js":"afma-sdk-a-v6.0.1","mv":"8013013.com.android.vending","isu":"2BB916E1BD6BE6407582A429D763EC71","cipa":1,"format":"320x50_mb","net":"wi","app_name":"1.android.com.mysampleapp.sampleapp","hl":"en","u_h":592,"carrier":"311480","ptime":0,"u_audio":3});</script></head><body></body></html> 07-09 09:13:17.041: W/ActivityManager(220): Unable to start service Intent { act=com.google.android.gms.analytics.service.START (has extras) }: not found 07-09 09:13:17.049: W/GAV2(13933): Thread[main,5,main]: Connection to service failed 1 07-09 09:13:17.057: W/GAV2(13933): Thread[main,5,main]: Need to call initializea() and be in fallback mode to start dispatch. 07-09 09:13:17.088: D/libEGL(13933): loaded /system/lib/egl/libGLES_android.so 07-09 09:13:17.096: D/libEGL(13933): loaded /vendor/lib/egl/libEGL_POWERVR_SGX540_120.so 07-09 09:13:17.096: D/libEGL(13933): loaded /vendor/lib/egl/libGLESv1_CM_POWERVR_SGX540_120.so 07-09 09:13:17.096: D/libEGL(13933): loaded /vendor/lib/egl/libGLESv2_POWERVR_SGX540_120.so Here is my code (I have redacted some of the code that had to do with httppost, etc.): package com.mysampleapp.sampleapp; import java.io.BufferedReader; import java.io.InputStream; import java.io.InputStreamReader; import java.util.ArrayList; import java.util.List; import org.apache.http.HttpEntity; import org.apache.http.HttpResponse; import org.apache.http.NameValuePair; import org.apache.http.client.HttpClient; import org.apache.http.client.entity.UrlEncodedFormEntity; import org.apache.http.client.methods.HttpPost; import org.apache.http.impl.client.DefaultHttpClient; import org.apache.http.message.BasicNameValuePair; import org.json.JSONArray; import org.json.JSONObject; import com.google.analytics.tracking.android.EasyTracker; import android.app.Activity; import android.app.ProgressDialog; import android.content.DialogInterface; import android.content.DialogInterface.OnCancelListener; import android.content.Intent; import android.content.SharedPreferences; import android.os.AsyncTask; import android.os.Bundle; import android.preference.PreferenceManager; import android.util.Log; import android.view.View; import android.view.View.OnClickListener; import android.widget.ImageView; import android.widget.TextView; public class viewRandom extends Activity { @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.viewrandom); uservote.setVisibility(View.GONE); new randomViewClass().execute(); } public void onStart() { super.onStart(); EasyTracker.getInstance().activityStart(this); } public void onStop() { super.onStop(); EasyTracker.getInstance().activityStop(this); } }

  Read the article

• Binding a property to change the listbox items foreground individually for each item

  - by Eyal-Shilony

  I'm trying to change the foreground color of the items in the ListBox individually for each item, I've already posted a similar question but this one is more concrete. I hoped that the state of the color is reserved for each item added to the ListBox, so I tried to create a property (in this case "HotkeysForeground"), bind it and change the color when the items are added in the "HotkeyManager_NewHotkey" event, the problem it's changing the foreground color for all the items in the ListBox. How can I do that per item ? Here is the ViewModel I use. namespace Monkey.Core.ViewModel { using System; using System.Collections.ObjectModel; using System.Windows.Media; using Monkey.Core.SystemMonitor.Accessibility; using Monkey.Core.SystemMonitor.Input; public class MainWindowViewModel : WorkspaceViewModel { private readonly FocusManager _focusManager; private readonly HotkeyManager _hotkeyManager; private readonly ObservableCollection<string> _hotkeys; private Color _foregroundColor; private string _title; public MainWindowViewModel() { _hotkeys = new ObservableCollection<string>(); _hotkeyManager = new HotkeyManager(); _hotkeyManager.NewHotkey += HotkeyManager_NewHotkey; _focusManager = new FocusManager(); _focusManager.Focus += FocusManager_Focus; } public Color HotkeysForeground { get { return _foregroundColor; } set { _foregroundColor = value; OnPropertyChanged(() => HotkeysForeground); } } public ReadOnlyObservableCollection<string> Hotkeys { get { return new ReadOnlyObservableCollection<string>(_hotkeys); } } public string Title { get { return _title; } set { _title = value; OnPropertyChanged(() => Title); } } protected override void OnDispose() { base.OnDispose(); _hotkeyManager.Dispose(); _focusManager.Dispose(); } private void FocusManager_Focus(object sender, FocusManagerEventArgs e) { Title = e.Title; } private void HotkeyManager_NewHotkey(object sender, EventArgs eventArgs) { HotkeysForeground = _hotkeys.Count <= 2 ? Colors.Blue : Colors.Brown; _hotkeys.Clear(); foreach (var hotkey in _hotkeyManager.GetHotkeys()) { _hotkeys.Add(hotkey); } } } } Here is the view. <Window x:Class="Monkey.View.MainWindow" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:System="clr-namespace:System;assembly=mscorlib" Title="{Binding Mode=OneWay, Path=Title, UpdateSourceTrigger=PropertyChanged}" Height="200" Width="200" ShowInTaskbar="False" WindowStyle="ToolWindow" Topmost="True" ResizeMode="CanResizeWithGrip" AllowsTransparency="False"> <Window.Resources> <SolidColorBrush Color="{Binding HotkeysForeground}" x:Key="HotkeysBrush"/> </Window.Resources> <ListBox Canvas.Left="110" Canvas.Top="74" Name="HotkeyList" Height="Auto" Width="Auto" HorizontalContentAlignment="Left" BorderThickness="0" ScrollViewer.CanContentScroll="False" ScrollViewer.HorizontalScrollBarVisibility="Disabled" ScrollViewer.VerticalScrollBarVisibility="Disabled" ItemsSource="{Binding Path=Hotkeys}" VerticalAlignment="Stretch" VerticalContentAlignment="Center" FontSize="20"> <ListBox.ItemContainerStyle> <Style TargetType="ListBoxItem"> <Setter Property="IsEnabled" Value="False" /> </Style> </ListBox.ItemContainerStyle> <ListBox.ItemTemplate> <DataTemplate> <Label Content="{Binding}" Foreground="{StaticResource HotkeysBrush}"/> </DataTemplate> </ListBox.ItemTemplate> </ListBox> </Window> Thank you in advance.

  Read the article

• Autodetect/mount SDCards and run script for them on Linux

  - by Brendan

  Hey Everyone, I'm currently running SME Server, and need to have a script run upon the attachment of SD Cards to my server. The script itself works fine (it copies the contents of the cards), but the automounting and execution of the script is where I'm having issues. The I have a USB hub consisting of 10 USB ports; that shows up as: [root@server ~]# lsusb Bus 004 Device 002: ID 0000:0000 Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 055: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 051: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 050: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 001: ID 0000:0000 (The hub is the TERMINUS TECHNOLOGY INC entries) As I cannot plug SD Cards directly into the server; I use a USB to SD card attachement (10 of them) plugged into the hub to read the cards. Upon pluggig the 10 attachments (without cards) into the hub; lsusb yields the following: [root@server ~]# lsusb Bus 004 Device 002: ID 0000:0000 Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 073: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 072: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 071: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 070: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 069: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 068: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 067: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 066: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 065: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 064: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 055: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 051: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 050: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 001: ID 0000:0000 As you can see, the readers are the "Gensys Logic, Inc" entries. Plugging in an SD card to a reader doesn't affect lsusb (it reads exactly as above), however my system recognises the cards fine; as indicated by dmesg: Attached scsi generic sg11 at scsi54, channel 0, id 0, lun 0, type 0 USB Mass Storage device found at 73 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 If I manually mount sdd1 (mount /dev/sdd1 /somedirectory/) this works fine. What I'm really after is a solution that automounts each of the cards as they are inputted into the reader; and executes a script for them (this will involve copying their contents to another directory). My problem is that I don't know how to do this; I don't think udev will work as the USB devices don't change; if I could somehow get udev working with /dev/disk/by-path/ however I think this is doable (it seems to keep constant entries). ls /dev/disk returns: pci-0000:00:1d.7-usb-0:4.1.1.1:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0-part1 pci-0000:0b:01.0-scsi-0:0:1:0 pci-0000:0b:01.0-scsi-0:0:1:0-part1 pci-0000:0b:01.0-scsi-0:0:1:0-part2 From above, we can see I have only one card plugged into the reader (pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0-part1). Going mount /dev/disk/by-path/pci-0000\:00\:1d.7-usb-0\:4.4\:1.0-scsi-0\:0\:0\:0-part1 Works and places the card under /media/usbdisk/, however: mount /dev/disk/by-path/pci-0000\:00\:1d.7-usb-0\:4.4\:1.0-scsi-0\:0\:0\:0-part1 slot1/ doesn't work, and returns "mount: can't get address for /dev/disk/by-path/pci-0000" Any ideas and solutions would be great, I've seen the knowledge of a lot of the guys on here before so I'm hopeful someone can help me out. Thanks

  Read the article

• Update to Easy Slider 1.7 made all my JQuery code stop working.

  - by Anders H

  I'm pretty novice as a JQuery user goes. I've got some experience implementing different plugins but would be lost trying to customize my own. I can't share the exact site details with you due to a NDA, so I hope someone can give me a little help. I've got a project due today (Just HTML/CSS/JQuery). It has a lightbox, show/hide login menu and a slider is Easy Slider 1.5. Everything was working together, until I attempted to update to Easy Slider 1.7 (see link on same page, I'm too new to post more than 1 link). When I did so, JQuery stopped working for all the plugins. I've attempted to revert back to the original state, by undoing my work (didn't do much), ad JQuery remains broken. Firebug Error Console shared no errors. I can't find anything in the code no matter how hard I look at it. Can anyone help me troubleshoot this JQuery problem? Delivery is supposed to be tonight for the project. EDIT: Generic header info: <!-- Global Style Sheet --> <link rel="stylesheet" href="style.css" media="screen" type="text/css" /> <!-- Cufon --> <script src="cufon/cufon.js" type="text/javascript"></script> <script src="cufon/gotham_325-gotham_350.font.js" type="text/javascript"></script> <!-- jQuery Javascript --> <script type="text/javascript" language="javascript" src="js/jquery-1.3.2.min.js"></script> <script type="text/javascript" language="javascript" src="js/jquery-ui-1.7.1.custom.min.js"></script> <script type="text/javascript" language="javascript" src="js/jquery.colorbox.js"></script> <script type="text/javascript" language="javascript" src="js/global.js"></script> <script type="text/javascript" language="javascript" src="js/home.js"></script> <script type="text/javascript"> $(document).ready(function() { $(".signin").click(function(e) { e.preventDefault(); $("fieldset#signin_menu").toggle(); $(".signin").toggleClass("menu-open"); }); $("fieldset#signin_menu").mouseup(function() { return false }); $(document).mouseup(function(e) { if($(e.target).parent("a.signin").length==0) { $(".signin").removeClass("menu-open"); $("fieldset#signin_menu").hide(); } }); }); </script> <script src="javascripts/jquery.tipsy.js" type="text/javascript"></script> <script type='text/javascript'> $(function() { $('#forgot_username_link').tipsy({gravity: 'w'}); }); </script> <script type="text/javascript" language="javascript" src="js/easySlider1.5.js"></script> <script type="text/javascript"> $(document).ready(function(){ $("#slider").easySlider(); }); </script> <script type="text/javascript"> $(document).ready(function(){ $(".regbox").colorbox({iframe:true, innerWidth:270, innerHeight:270}); }); </script>

  Read the article

• MIME "Content-Type" folding and parameter question regarding RFCs?

  - by BastiBense

  Hello, I'm trying to implement a basic MIME parser for the multipart/related in C++/Qt. So far I've been writing some basic parser code for headers, and I'm reading the RFCs to get an idea how to do everything as close to the specification as possible. Unfortunately there is a part in the RFC that confuses me a bit: From RFC882 Section 3.1.1: Each header field can be viewed as a single, logical line of ASCII characters, comprising a field-name and a field-body. For convenience, the field-body portion of this conceptual entity can be split into a multiple-line representation; this is called "folding". The general rule is that wherever there may be linear-white-space (NOT simply LWSP-chars), a CRLF immediately followed by AT LEAST one LWSP-char may instead be inserted. Thus, the single line Alright, so I simply parse a header field and if a CRLF follows with linear whitespace, I simply concat those in a useful manner to result in a single header line. Let's proceed... From RFC2045 Section 5.1: In the Augmented BNF notation of RFC 822, a Content-Type header field value is defined as follows: content := "Content-Type" ":" type "/" subtype *(";" parameter) ; Matching of media type and subtype ; is ALWAYS case-insensitive. [...] parameter := attribute "=" value attribute := token ; Matching of attributes ; is ALWAYS case-insensitive. value := token / quoted-string token := 1*<any (US-ASCII) CHAR except SPACE, CTLs, or tspecials> Okay. So it seems if you want to specify a Content-Type header with parameters, simple do it like this: Content-Type: multipart/related; foo=bar; something=else ... and a folded version of the same header would look like this: Content-Type: multipart/related; foo=bar; something=else Correct? Good. As I kept reading the RFCs, I came across the following in RFC2387 Section 5.1 (Examples): Content-Type: Multipart/Related; boundary=example-1 start="<[email protected]>"; type="Application/X-FixedRecord" start-info="-o ps" --example-1 Content-Type: Application/X-FixedRecord Content-ID: <[email protected]> [data] --example-1 Content-Type: Application/octet-stream Content-Description: The fixed length records Content-Transfer-Encoding: base64 Content-ID: <[email protected]> [data] --example-1-- Hmm, this is odd. Do you see the Content-Type header? It has a number of parameters, but not all have a ";" as parameter delimiter. Maybe I just didn't read the RFCs correctly, but if my parser works strictly like the specification defines, the type and start-info parameters would result in a single string or worse, a parser error. Guys, what's your thought on this? Just a typo in the RFCs? Or did I miss something? Thanks!

  Read the article

• Deployment Workbench no longer available after PXE boot

  - by Patrick

  Our build process revolves around windows Deployment Workbench. Unfortunately this was setup by someone who is no longer with the company, and no-one has ever dared/needed to make any changes. The other day it stopped working. It turns out that one of our build guys started thinking about changing some stuff in it, clicked something and now it no longer works (He is saying now that he right clicked on the 'LAB' entry in 'Deployment points' and hit 'Update', which took some time to run through apparently). The job has fallen on me to resolve and frankly I'm not sure what I'm doing. I was wondering if someone with more experience than me can provide some pointers as to troubleshooting cos I'm feeling quite a lot in the dark here. On the server I have Deployment Workbench up and running (MMC snapin) version 3.0. There is a WDS service that appears to be running ok, as does the tFTPd service. Nothing specific to this in event logs. From the client side; PXE boot works and gets you to the Win PE launch, and it has the correct company logo as the background (proving to me that its loading win PE from the network). WPEINIT runs, and asks for domain credentials, here the team simply put User/Pass/Domain in the boxes and click ok. Normally the build would kick off. Instead they get an error message saying that the \NATBLU01\Distribution$ share isn't available. Checking \NATBLU01\Distribution$ shows that its there and accessible over the network. Security/permissions seem ok, even 'ANONYMOUS LOGON' has read access to that share so I don't see that being a problem. Digging the trace files from C:\MININT\SMSOSD\OSDLOGS\ after an attempt to run the build I can see an error saying much the same - <![LOG[Validating connection to \\NATBLU01\Distribution$]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[FindFile: The file OSDConnectToUNC.exe could not be found in any standard locations.]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[The network location cannot be reached. For information about network troubleshooting, see Windows Help.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> <![LOG[ERROR - Unable to map a network drive to \\NATBLU01\Distribution$.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> BDD.LOG shows much the same. Full copies of the .LOG files can both files be found here : BDD.LOG LITETOUCH.LOG I can get to a command prompt from the Win PE that boots from PXE, however there isn't any network stuff there. IPCONFIG returns nothing so none of the tests I would usually run resolve anything. I'm at a loss frankly. I did wonder if I could perhaps start a new build process but if the change to the DeploymentWorkbench has knocked it offline I don't think I'm going to be able to create a new deployment. Failing that; we do have a deployment point labeled type 'Media' which appears to be a DVD ISO image of one of the builds, but its dated 2008, is it possible to export the network build to .ISO and build from DVD? We are looking at new hardware to run this from anyway (for the impending Windows 7 roll out) so a temporary work round isn't going to be too much of a problem. All assistance is appreciated! EDIT : OK. Got it working again. Solution was close to Newmanth's idea. The problem was that our PE image didn't appear to be connecting the network. I had an older copy of the PE boot.WIM on a stick that I had been using for other purposes. I booted that and correctly got a network connection. Showed a correct internal IP and could ping out etc etc. However I was still getting the same errors in all the logs and in when wpeinit was running. What I did seperately was to update the PE image that DeploymentWorkbench was pushing out to display a different back ground. I wanted to prove that I was working in the correct place. Turns out that I wasn't. I went and looked at the other deployment stuff we had on this machine, Windows Deployment Services was installed and although all the install images are off line the boot image was online, so I uploaded the copy from my stick to that. Booted straight off. And fixed. Working. Yay! For anyone stumbling across this in the future you may find that although your deployment images are located in the DeploymentWorkbench, the Win PE boot image you are launching from is located in the associated Windows Deployment Services images.

  Read the article

• Can't access shared drive when connecting over VPN

  - by evolvd

  I can ping all network devices but it doesn't seem that DNS is resolving their hostnames. ipconfig/ all is showing that I am pointing to the correct dns server. I can "ping "dnsname"" and it will resolve but it wont resolve any other names. Split tunnel is set up so outside DNS is resolving fine So one issue might be DNS but I have the IP address of the server share so I figure I could just get to it that way. example: \10.0.0.1\ well I can't get to it that way either and I get "the specified network name is no longer available" I can ping it but I can't open the share. Below is the ASA config : ASA Version 8.2(1) ! hostname KG-ASA domain-name example.com names ! interface Vlan1 nameif inside security-level 100 ip address 10.0.0.253 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns domain-lookup outside dns server-group DefaultDNS name-server 10.0.0.101 domain-name blah.com access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 10000 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 8333 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 902 access-list SPLIT-TUNNEL-VPN standard permit 10.0.0.0 255.0.0.0 access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool IPSECVPN-POOL 10.0.1.2-10.0.1.50 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 10000 10.0.0.101 10000 netmask 255.255.255.255 static (inside,outside) tcp interface 8333 10.0.0.101 8333 netmask 255.255.255.255 static (inside,outside) tcp interface 902 10.0.0.101 902 netmask 255.255.255.255 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication enable console LOCAL aaa authentication http console LOCAL aaa authentication serial console LOCAL aaa authentication ssh console LOCAL aaa authentication telnet console LOCAL http server enable http 10.0.0.0 255.255.0.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set myset esp-aes esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map dynmap 1 set transform-set myset crypto dynamic-map dynmap 1 set reverse-route crypto map IPSEC-MAP 65535 ipsec-isakmp dynamic dynmap crypto map IPSEC-MAP interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption aes hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 0.0.0.0 0.0.0.0 inside ssh 70.60.228.0 255.255.255.0 outside ssh 74.102.150.0 255.255.254.0 outside ssh 74.122.164.0 255.255.252.0 outside ssh timeout 5 console timeout 0 dhcpd dns 10.0.0.101 dhcpd lease 7200 dhcpd domain blah.com ! dhcpd address 10.0.0.110-10.0.0.170 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 63.111.165.21 webvpn enable outside svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable group-policy EASYVPN internal group-policy EASYVPN attributes dns-server value 10.0.0.101 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-policy tunnelspecified split-tunnel-network-list value SPLIT-TUNNEL-VPN ! tunnel-group client type remote-access tunnel-group client general-attributes address-pool (inside) IPSECVPN-POOL address-pool IPSECVPN-POOL default-group-policy EASYVPN dhcp-server 10.0.0.253 tunnel-group client ipsec-attributes pre-shared-key * tunnel-group CLIENTVPN type ipsec-l2l tunnel-group CLIENTVPN ipsec-attributes pre-shared-key * ! class-map inspection_default match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect icmp ! service-policy global_policy global prompt hostname context I'm not sure where I should go next with troubleshooting nslookup result: Default Server: blahname.blah.lan Address: 10.0.0.101

  Read the article

• jQuery: Div elements are not showing up

  - by Legend

  I am adapting the Coverflow technique to work with a div. Following is the html: <html> <head> <meta http-equiv="Content-type" content="text/html; charset=utf-8" /> <style type="text/css" media="screen"> body,html { margin: 0; padding: 0; background: #000; height: 100%; color: #eee; font-family: Arial; font-size: 10px; } div.magnifyme { height: 80px; padding: 80px; position: absolute; top: 0px; left: 0px; width: 8000px; } div.wrapper { margin: 0px; height: 470px; /*border: 2px solid #999;*/ overflow: hidden; padding-left: 40px; right: 1px; width: 824px; position: relative; } div.container {position: relative; width: 854px; height: 480px; background: #000; margin: auto;} div.nav {position: absolute; top: 10px; width: 20%; height: 10%; right: 1px; } div.magnifyme div { position: absolute; width: 300px; height: 280px; float: left; margin: 5px; position: relative; border: 2px solid #999; background: #500; } </style> <script type="text/javascript" src="jquery-1.3.2.js"></script> <script type="text/javascript" src="ui.coverflow.js"></script> <script type="text/javascript"> $(function() { $("div.magnifyme").coverflow(); $("#add").click(function() { location.reload(); $(".magnifyme").append("<div id=\"div5\">hello world</div>"); $("div.magnifyme").coverflow(); }); }); </script> </head> <body> <div class="container"> <div class="wrapper"> <div class="magnifyme"> <div id="div0">This is div 0</div> <div id="div1">This is div 1</div> <div id="div2">This is div 2</div> <div id="div3">This is div 3</div> <div id="div4">This is div 4</div> </div> </div> <div class="nav"> <button type="button" id="add">Add to Deck</button> </div> </div> </body> </html> The coverflow function (included as a js file in the head section) is here. When I click the button, I was expecting it to add a DIV to the already present deck. For some reason, it doesn't show the newly added DIV. I tried calling the coverflow() function after I added the new element but that didn't work either. Is there any way I can make this work?

  Read the article

• Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

  - by Linux Guy

  I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• Search Form in Responsive Design - Remove Search button on Mobile

  - by Kevin

  I'm working with a search box in the header of a responsive website. On desktop/tablet widths, there's a search input field and a styled 'search' button to the right. You can type in a search term and either click 'SEARCH' button or just hit enter on the keyboard with the same result. When you scale down to mobile widths, the search input field fills the width of the screen. The submit button falls below it. On a desktop, clicking the button or hitting enter activate the search. On an actual iphone phone, you can hit the 'SEARCH' button, but the native mobile keyboard that rises from the bottom of the screen has a search button where the enter/return key would normally be. It seems to know I'm in a form and the keyboard automatically gives me the option to kick off the search by basically hitting the ENTER key location....but it says SEARCH. So far so good. I figure I don't need the button in the header on mobile since it's already in the keyboard. Therefore, I'll hide the button on mobile widths and everything will be tighter and look better. So I added this to my CSS to hide it in mobile: #search-button {display: none;} But now the search doesn't work at all. On mobile, I don't get the option in the keyboard that showed up before and if I just hit enter, it doesn't work at all. On desktop at mobile width, hitting enter also not longer works. So clearly by hiding the submit/search button, the phone no longer gave me the native option to run the search. In addition, on the desktop at mobile width, even hitting enter inside the search input box also fails to launch the the search. Here's my search box: <form id="search-form" method="get" accept-charset="UTF-8, utf-8" action="search.php"> <fieldset> <div id="search-wrapper"> <label id="search-label" for="search">Item:</label> <input id="search" class="placeholder-color" name="item" type="text" placeholder="Item Number or Description" /> <button id="search-button" title="Go" type="submit"><span class="search-icon"></span></button> </div> </fieldset> </form> Here's what my CSS looks like: #search-wrapper { float: left; display: inline-block; position: relative; white-space: nowrap; } #search-button { display: inline-block; cursor: pointer; vertical-align: top; height: 30px; width: 40px; } @media only screen and (max-width: 639px) { #search-wrapper { display: block; margin-bottom: 7px; } #search-button { /* this didn't work....it hid the button but the search failed to load */ display: none;*/ } } So.....how can I hide this submit button when I'm on a mobile screen, but still let the search run from the mobile keyboard or just run by hitting enter when in the search input box. I was sure that putting display:none on the search button at mobile width would do the trick, but apparently not. Thanks...

  Read the article

• Looping through siblings of a specific row/setting up function

  - by Matt

  Trying to work through my javascript book I am referencing to learn the language and got stuck on looping through siblings of a specific row. W3schools and W3 didnt have what i was looking for. Below is a function walk-through... It reads: Create the countRecords() function. The purpose of this function is to count the number of visible rows in the data table after the table headings. The total is then displayed in the table cell with the id "records". Add the follow commands to the function: a. Create a object named headRow that points to the table row with the id "titleRow". Create a variable named rowCount, setting its initial value to 0. b. Create a for loop that uses familial references starting with the first sibling of headRow and moving to the next sibling until there are no siblings left. Within the for loop. test whether the node name of the currentnext sibling until there are no sibilings left. Within the for loop test whether the node name of the current node is equal to "TR". If it is, test wheter the value of its display style is equal to an empty text string. If it is (indicating that it is visible in the document) increate the value of the rowCount variable by 1. c. Change the text of the "records" table cell to the value of the rowCount variable. Don't use innerHTML. Create a text node that contains the value of the rowCount variable and assign it to a variable called txt. Create a variable called record to store the reference to the element "records" table cell. d. Insert an if condition that test whether the "records" cell has any child nodes. If it does, replace the replace the text node of the "record" table cell with the created text node (txt). If it doesn't append the text node to the cell. var headRow; // part a var rowCount = 0; //part b this is where I get lost. I know I need to access the id titleRow but unsure how to set my loop up specifically for this headRow = document.getElementById("titleRow"); for(var i=0; i<headrow.length; i++) { if (something is not equal == "TH") { make code happen here } if (is "TR" == ""){ rowCount = +1; } //part c var txt = document.createTextNode(rowCount); var record = document.getElementsById("records") //part d holding off on this part until I get a,b,c figured out. The HTML supporting snippet: <table id="filters"> <tr><th colspan="2">Filter Product List</th></tr> <tr> <td>Records: </td> <td id="records"></td> </tr> <table id="prodTable"> <tr><th colspan="8">Digital Cameras</th></tr> <tr id="titleRow"> <th>Model</th> <th>Manufacturer</th> <th>Resolution</th> <th>Zoom</th> <th>Media</th> <th>Video</th> <th>Microphone</th> </tr> Thanks for the help!

  Read the article

• nginx returning authentication in IE

  - by James MacLeod

  I am having a few issues with an nginx server. I have a site setup that keeps requesting authentication when accessed from IE but in firefox and safari the site is fine no request for authentication. Reading around the web I can see that it could be the gzip that may be causing errors, but the other sites are working without issue. Here is the config: user sysadmin sysadmin; worker_processes 8; error_log logs/error.log debug; events { worker_connections 1024; } http { passenger_root /usr/lib/ruby/gems/1.8/gems/passenger-2.2.9; passenger_ruby /usr/bin/ruby1.8; include mime.types; default_type application/octet-stream; client_header_timeout 3m; client_body_timeout 3m; client_max_body_size 5m; send_timeout 3m; client_header_buffer_size 1k; large_client_header_buffers 4 4k; gzip on; gzip_min_length 1100; gzip_buffers 4 8k; gzip_types text/plain; output_buffers 1 32k; postpone_output 1460; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 75 20; server { listen 80; server_name .reg-power.com .reg-power.co.uk .reg-power.eu .reg-power.eu.com .reg-power.net .reg-power.org .reg-power.org.uk .reg-power.uk.com .regegen.eu .regpower.co.uk .regpower.eu .regpower.eu.com .regpower.net .regpower.org .regpower.org.uk .regpower.uk.com .renegen.com .renegen.eu .renewableenergygeneration.co.uk .renewableenergygeneration.com reg.rails1.flowhost.co.uk; root /home/sysadmin/reg/current/public; passenger_enabled on; rails_env production; index index.html; } server { listen 80; server_name media.reg-power.com; root /home/sysadmin/admin/current/public; index index.html; } server { listen 80; server_name admin.reg-power.com admin.rails1.flowhost.co.uk; root /home/sysadmin/admin/current/public; passenger_enabled on; rails_env production; index index.html; } server { listen 80; server_name .livingfuels.co.uk livingfuels.rails1.flowhost.co.uk; root /home/sysadmin/livingfuels/current/public; passenger_enabled on; rails_env production; index index.html; } server { listen 80; server_name .regbiopower.com .regbiopower.co.uk regbiopower.rails1.flowhost.co.uk; root /home/sysadmin/regbiopower/current/public; passenger_enabled on; rails_env production; index index.html; } server { listen 80; server_name .clpwindprojects.co.uk clp.rails1.flowhost.co.uk; access_log /home/sysadmin/clp/logs/access.log; location / { root /home/sysadmin/clp; index index.php; if (-f $request_filename) { expires 30d; break; } if (!-e $request_filename) { rewrite ^(.+)$ /index.php?q=$1 last; } } location ~ .php$ { fastcgi_pass 127.0.0.1:49232; #this must point to the socket spawn_fcgi is running on. fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /home/sysadmin/clp$fastcgi_script_name; # same path as above fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT /home/sysadmin/clp; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; } } } As you can see there is no reference to a http authentication

  Read the article

• [C] Texture management / pointer question

  - by ndg

  I'm working on a texture management and animation solution for a small side project of mine. Although the project uses Allegro for rendering and input, my question mostly revolves around C and memory management. I wanted to post it here to get thoughts and insight into the approach, as I'm terrible when it comes to pointers. Essentially what I'm trying to do is load all of my texture resources into a central manager (textureManager) - which is essentially an array of structs containing ALLEGRO_BITMAP objects. The textures stored within the textureManager are mostly full sprite sheets. From there, I have an anim(ation) struct, which contains animation-specific information (along with a pointer to the corresponding texture within the textureManager). To give you an idea, here's how I setup and play the players 'walk' animation: createAnimation(&player.animations[0], "media/characters/player/walk.png", player.w, player.h); playAnimation(&player.animations[0], 10); Rendering the animations current frame is just a case of blitting a specific region of the sprite sheet stored in textureManager. For reference, here's the code for anim.h and anim.c. I'm sure what I'm doing here is probably a terrible approach for a number of reasons. I'd like to hear about them! Am I opening myself to any pitfalls? Will this work as I'm hoping? anim.h #ifndef ANIM_H #define ANIM_H #define ANIM_MAX_FRAMES 10 #define MAX_TEXTURES 50 struct texture { bool active; ALLEGRO_BITMAP *bmp; }; struct texture textureManager[MAX_TEXTURES]; typedef struct tAnim { ALLEGRO_BITMAP **sprite; int w, h; int curFrame, numFrames, frameCount; float delay; } anim; void setupTextureManager(void); int addTexture(char *filename); int createAnimation(anim *a, char *filename, int w, int h); void playAnimation(anim *a, float delay); void updateAnimation(anim *a); #endif anim.c void setupTextureManager() { int i = 0; for(i = 0; i < MAX_TEXTURES; i++) { textureManager[i].active = false; } } int addTextureToManager(char *filename) { int i = 0; for(i = 0; i < MAX_TEXTURES; i++) { if(!textureManager[i].active) { textureManager[i].bmp = al_load_bitmap(filename); textureManager[i].active = true; if(!textureManager[i].bmp) { printf("Error loading texture: %s", filename); return -1; } return i; } } return -1; } int createAnimation(anim *a, char *filename, int w, int h) { int textureId = addTextureToManager(filename); if(textureId > -1) { a->sprite = textureManager[textureId].bmp; a->w = w; a->h = h; a->numFrames = al_get_bitmap_width(a->sprite) / w; printf("Animation loaded with %i frames, given resource id: %i\n", a->numFrames, textureId); } else { printf("Texture manager full\n"); return 1; } return 0; } void playAnimation(anim *a, float delay) { a->curFrame = 0; a->frameCount = 0; a->delay = delay; } void updateAnimation(anim *a) { a->frameCount ++; if(a->frameCount >= a->delay) { a->frameCount = 0; a->curFrame ++; if(a->curFrame >= a->numFrames) { a->curFrame = 0; } } }

  Read the article

< Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >