Search Results

Search found 6715 results on 269 pages for 'preg match'.

Page 254/269 | < Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• Need some help deciphering a line of assembler code, from .NET JITted code

  - by Lasse V. Karlsen

  In a C# constructor, that ends up with a call to this(...), the actual call gets translated to this: 0000003d call dword ptr ds:[199B88E8h] What is the DS register contents here? I know it's the data-segment, but is this call through a VMT-table or similar? I doubt it though, since this(...) wouldn't be a call to a virtual method, just another constructor. I ask because the value at that location seems to be bad in some way, if I hit F11, trace into (Visual Studio 2008), on that call-instruction, the program crashes with an access violation. The code is deep inside a 3rd party control library, where, though I have the source code, I don't have the assemblies compiled with enough debug information that I can trace it through C# code, only through the disassembler, and then I have to match that back to the actual code. The C# code in question is this: public AxisRangeData(AxisRange range) : this(range, range.Axis) { } Reflector shows me this IL code: .maxstack 8 L_0000: ldarg.0 L_0001: ldarg.1 L_0002: ldarg.1 L_0003: callvirt instance class DevExpress.XtraCharts.AxisBase DevExpress.XtraCharts.AxisRange::get_Axis() L_0008: call instance void DevExpress.XtraCharts.Native.AxisRangeData::.ctor(class DevExpress.XtraCharts.ChartElement, class DevExpress.XtraCharts.AxisBase) L_000d: ret It's that last call there, to the other constructor of the same class, that fails. The debugger never surfaces inside the other method, it just crashes. The disassembly for the method after JITting is this: 00000000 push ebp 00000001 mov ebp,esp 00000003 sub esp,14h 00000006 mov dword ptr [ebp-4],ecx 00000009 mov dword ptr [ebp-8],edx 0000000c cmp dword ptr ds:[18890E24h],0 00000013 je 0000001A 00000015 call 61843511 0000001a mov eax,dword ptr [ebp-4] 0000001d mov dword ptr [ebp-0Ch],eax 00000020 mov eax,dword ptr [ebp-8] 00000023 mov dword ptr [ebp-10h],eax 00000026 mov ecx,dword ptr [ebp-8] 00000029 cmp dword ptr [ecx],ecx 0000002b call dword ptr ds:[1889D0DCh] // range.Axis 00000031 mov dword ptr [ebp-14h],eax 00000034 push dword ptr [ebp-14h] 00000037 mov edx,dword ptr [ebp-10h] 0000003a mov ecx,dword ptr [ebp-0Ch] 0000003d call dword ptr ds:[199B88E8h] // this(range, range.Axis)? 00000043 nop 00000044 mov esp,ebp 00000046 pop ebp 00000047 ret Basically what I'm asking is this: What the purpose of the ds:[ADDR] indirection here? VMT-table is only for virtual isn't it? and this is constructor Could the constructor have yet to be JITted, which could mean that the call would actually call through a JIT shim? I'm afraid I'm in deep water here, so anything might and could help. Edit: Well, the problem just got worse, or better, or whatever. We are developing the .NET feature in a C# project in a Visual Studio 2008 solution, and debugging and developing through Visual Studio. However, in the end, this code will be loaded into a .NET runtime hosted by a Win32 Delphi application. In order to facilitate easy experimentation of such features, we can also configure the Visual Studio project/solution/debugger to copy the produced dll's to the Delphi app's directory, and then execute the Delphi app, through the Visual Studio debugger. Turns out, the problem goes away if I run the program outside of the debugger, but during debugging, it crops up, every time. Not sure that helps, but since the code isn't slated for production release for another 6 months or so, then it takes some of the pressure off of it for the test release that we have soon. I'll dive into the memory parts later, but probably not until over the weekend, and post a followup.

  Read the article

• Set up linux box for hosting a-z

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP/MySQL: To upgrade PHP and MySQL to the latest versions, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! Add IUS repository to our package manager cd /tmp wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. # list all the packages in the IUS repository; use this to find PHP/MySQL version and libraries you want to install Remove old version of PHP and install newer version from IUS rpm -qa | grep php # to list all of the installed php packages we want to remove yum shell # open an interactive yum shell remove php-common php-mysql php-cli #remove installed PHP components install php53 php53-mysql php53-cli php53-common #add packages you want transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) Upgrade MySQL from IUS repository /etc/init.d/mysqld stop rpm -qa | grep mysql # to see installed mysql packages yum shell remove mysql mysql-server #remove installed MySQL components install mysql51 mysql51-server mysql51-devel transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell service mysqld start mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project Upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Install rssh (restricted shell) to provide scp and sftp access, without allowing ssh login cd /tmp wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm useradd -m -d /home/dev -s /usr/bin/rssh dev passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. vi /etc/rssh.conf Uncomment or add: allowscp allowsftp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). rssh instructions appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html Set up virtual interfaces ifconfig eth1:1 192.168.1.3 up #start up the virtual interface cd /etc/sysconfig/network-scripts/ cp ifcfg-eth1 ifcfg-eth1:1 #copy default script and match name to our virtual interface vi ifcfg-eth1:1 #modify eth1:1 script #ifcfg-eth1:1 | modify so it looks like this: DEVICE=eth1:1 IPADDR=192.168.1.3 NETMASK=255.255.255.0 NETWORK=192.168.1.0 ONBOOT=yes NAME=eth1:1 Add more Virtual interfaces as needed by repeating. Because of the ONBOOT=yes line in the ifcfg-eth1:1 file, this interface will be brought up when the system boots, or the network starts/restarts. service network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Bringing up interface eth1: [ OK ] ping 192.168.1.3 64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.105 ms And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

  Read the article

• Corrupt mercurial repository - cannot update

  - by richzilla

  Hi all, i think ive managed to corrupt one of mercurial repositories, is there anyway to recover the damage? the message i get when attempting to update the repo to my default branch is: PS C:\wco\projects\ims\code> hg up -C default abort: data/Trunk/application/models/priority_model.php.i@83dbdfb60981: no match found! when i run hg verify, i get the following report: PS C:\wco\projects\ims\code> hg verify checking changesets checking manifests crosschecking files in changesets and manifests checking files data/.buildpath.i@0: missing revlog! 0: empty or missing .buildpath .buildpath@0: daf15acb5273 in manifests not found data/.project.i@0: missing revlog! 0: empty or missing .project .project@0: e8b25997d6d1 in manifests not found Rawlings IMS/index.html@3: empty or missing copy source revlog index.html:b8b2b36a6eea Rawlings IMS/index.php@3: empty or missing copy source revlog index.php:a5f76bf232e9 Rawlings IMS/index_backup.php@3: empty or missing copy source revlog index_backup.php:a5f76bf232e9 Rawlings IMS/index_this_hold.html@3: empty or missing copy source revlog index_this_hold.html:b8b2b36a6eea Rawlings IMS/testera.php@3: empty or missing copy source revlog testera.php:6e9e3666c1bc Trunk/application/models/priority_model.php@32: 83dbdfb60981 in manifests not found data/index.html.i@0: missing revlog! 0: empty or missing index.html index.html@0: b8b2b36a6eea in manifests not found data/index.php.i@0: missing revlog! 0: empty or missing index.php index.php@0: a5f76bf232e9 in manifests not found data/index_backup.php.i@0: missing revlog! 0: empty or missing index_backup.php index_backup.php@0: a5f76bf232e9 in manifests not found data/index_this_hold.html.i@0: missing revlog! 0: empty or missing index_this_hold.html index_this_hold.html@0: b8b2b36a6eea in manifests not found data/nbproject/project.properties.i@14: missing revlog! 14: empty or missing nbproject/project.properties nbproject/project.properties@14: 1efa3074378b in manifests not found data/nbproject/project.xml.i@14: missing revlog! 14: empty or missing nbproject/project.xml nbproject/project.xml@14: 52689bf2b35a in manifests not found data/rcrawley/.buildpath.i@9: missing revlog! 9: empty or missing rcrawley/.buildpath rcrawley/.buildpath@9: 2c6411d4fcff in manifests not found data/rcrawley/.project.i@9: missing revlog! 9: empty or missing rcrawley/.project rcrawley/.project@9: cb4b1495acab in manifests not found data/rcrawley/assets/images/ajax-loader.gif.i@9: missing revlog! 9: empty or missing rcrawley/assets/images/ajax-loader.gif rcrawley/assets/images/ajax-loader.gif@9: 8ef26516c7da in manifests not found data/rcrawley/index.html.i@9: missing revlog! 9: empty or missing rcrawley/index.html rcrawley/index.html@9: 545246299dee in manifests not found data/rcrawley/index.php.i@9: missing revlog! 9: empty or missing rcrawley/index.php rcrawley/index.php@9: 66eac798ed6d in manifests not found data/rcrawley/index_backup.php.i@9: missing revlog! 9: empty or missing rcrawley/index_backup.php rcrawley/index_backup.php@9: 93971228fbf5 in manifests not found data/rcrawley/system/index.html.i@9: missing revlog! 9: empty or missing rcrawley/system/index.html rcrawley/system/index.html@9: 17360d3b566e in manifests not found data/rcrawley/testera.php.i@9: missing revlog! 9: empty or missing rcrawley/testera.php rcrawley/testera.php@9: 7d9bd5196740 in manifests not found data/testera.php.i@0: missing revlog! 0: empty or missing testera.php testera.php@0: 6e9e3666c1bc in manifests not found 1646 files, 59 changesets, 1897 total revisions 57 integrity errors encountered! (first damaged changeset appears to be 0) since the first damaged changeset is 0, this would appear to be pretty terminal. Is there anyway around this? any help would be appreciated.

  Read the article

• Icon for shortcut

  - by Jacek

  Hi! Could you tell me what is wrong in this code?? Why it doesn't work?? <?xml version="1.0" encoding="utf-8"?> <Icon Id="ikonka" SourceFile="Files\AdministKOB.exe"/> <Directory Id="TARGETDIR" Name="SourceDir"> <Directory Id="DesktopFolder"/> <Directory Id="ProgramMenuFolder"> <!--<Directory Id="MenuStartProduct" Name="Administrator KOB"/>--> </Directory> <Directory Id="ProgramFilesFolder"> <Directory Id="INSTALLLOCATION" Name="Administ_KOB"> <!-- TODO: Remove the comments around this Component element and the ComponentRef below in order to add resources to this installer. --> <Component Id="ProductComponent" Guid="6bd37582-5219-4ae4-a56e-cd1ecd375efa"> <!-- TODO: Insert files, registry keys, and other resources here. --> <File Id="AdministKOB" Name="AdministKOB.exe" Source="Files\AdministKOB.exe" KeyPath="yes"> <Shortcut Advertise="yes" Id="DesktopShortcut" Directory="DesktopFolder" Name="AdministKOB" WorkingDirectory="INSTALLDIR" Description="Elektroniczna ksiazka budynku" Icon ="ikonka"> </Shortcut> </File> <!--<File Id="ikonka" Name="C.ico" DiskId="1" Source="City.ico" Vital="yes" />--> </Component> <Component Id="ProductComponent_cfg" Guid="6bd37582-5219-4ae4-a56e-cd1ecd375efb"> <File Id="data.cfg" Name="data.cfg" Source="Files\data.cfg" /> </Component> <Component Id="ProductComponent_dll" Guid="6bd37582-5219-4ae4-a56e-cd1ecd375efc"> <File Id="DB.dll" Name="DB.dll" Source="Files\DB.dll" /> </Component> <Directory Id="Data"> <Directory Id="Data_1" Name="Data"> <Component Id="ProductComponent_mdf" DiskId="1" Guid="45B88917-DB08-4C4A-9DE4-D41BCE449BA5"> <File Id="bazaKOB.mdf" Name="bazaKOB.mdf" Source="Files\Data\bazaKOB.mdf" /> </Component> <Component Id="ProductComponent_ldf" DiskId="1" Guid="EFEBF7C5-338C-417C-8F5B-3C3BDE46F8EB"> <File Id="bazaKOB_log.LDF" Name="bazaKOB_log.LDF" Source="Files\Data\bazaKOB_log.LDF" /> </Component> </Directory> </Directory> </Directory> </Directory> </Directory> <Feature Id="ProductFeature" Title="AdministKOB" Level="1"> <!-- TODO: Remove the comments around this ComponentRef element and the Component above in order to add resources to this installer. --> <ComponentRef Id="ProductComponent" /> <ComponentRef Id="ProductComponent_cfg" /> <ComponentRef Id="ProductComponent_dll" /> <ComponentRef Id="ProductComponent_mdf" /> <ComponentRef Id="ProductComponent_ldf" /> </Feature> <Property Id="WIXUI_INSTALLDIR" Value="INSTALLLOCATION" /> <UIRef Id="WixUI_InstallDir" /> <WixVariable Id="WixUIDialogBmp" Value="background_projectUp.bmp" /> <WixVariable Id="WixUILicenseRtf" Value="license.rtf" /> <UI /> </Product> I get this error and warnings: The extension of Icon 'ikonka' for Shortcut 'DesktopShortcut' is not "exe" or "ico". The Icon will not be displayed correctly. Why?? I give ICO file. The extension of Icon 'ikonka' for Shortcut 'DesktopShortcut' does not match the extension of the Key File for component 'ProductComponent'. Have you any idea?? Thanks for all:) Jacek

  Read the article

• simplfy javascript code using regex

  - by Pradyut Bhattacharya

  Hi I have a code which can show youtube videos if there are any links to youtube in the text like for example the text example at:- pradyut.dyndns.org http://www.youtube.com/watch?v=-LiPMxFBLZY testing http://www.youtube.com/watch?v=Q3-l22b_Qg8&feature=related this text i m forwarding to the function... function to_youtubelink(text) { if ( text.indexOf ('<') > 0 || text.indexOf ('"') > 0 || text.indexOf ('>') > 0 ) return text; else { var obj_text = new Array(); var oi = 0; while(text.indexOf('http://') >=0) { //getting the paths var si = text.indexOf('http://'); var gr = text.indexOf('\n', si); var sp = text.indexOf(' ', si); var ei; if ( gr > 0 || sp > 0 ) { if ( gr >0 && sp > 0 ) { if ( gr < sp ) { ei = gr ; } else { ei = sp ; } } else if ( gr > 0) { ei = gr; } else { ei = sp; } } else { ei = text.length; } var it = text.substring(si,ei); if ( it.indexOf('"') > 0) { it.substring(0, it.indexOf('"') ); } if(ei < 0) ei = text.length; else ei = text.indexOf(' ', si) ; obj_text[oi] = it; text = text.replace( it, '[link_service]'); oi++; } var ob_text = new Array(); var ob =0; for (oi=0; oi<obj_text.length; oi++) { if ( is_youtubelink( obj_text[oi] ) ) { ob_text[ob] = to_utubelink(obj_text[oi]); ob++; } } oi = 0; while ( text.indexOf('[link_service]') >=0 ) { text = text.replace( '[link_service]', obj_text[oi]); oi ++; } for (ob=0; ob<ob_text.length; ob++) { text = text +"\n\n" + ob_text[ob]; } return text; } } function is_youtubelink(text) { var matches = text.match(/http:\/\/(?:www\.)?youtube.*watch\?v=([a-zA-Z0-9\-_]+)/); if (matches) { return true; } else { return false; } } function to_utubelink(text) { var video_id = text.split('v=')[1]; var ampersandPosition = video_id.indexOf('&'); if(ampersandPosition != -1) { video_id = video_id.substring(0, ampersandPosition); } text = "<iframe title=\"YouTube video player\" class=\"youtube-player\" type=\"text/html\" width=\"425\" height=\"350\" src=\"http://www.youtube.com/embed/" + video_id + "\" frameborder=\"0\"></iframe>" return text; } now i m getting the output properly... but i was thinking if the code could be done better and simplified using regex ...especially getting the urls part... thanks

  Read the article

• Someone please help google create instuctions that windows users understand. googles "instructions"

  - by nathan

  Below are the only instructions i managed to find from google on how to install the android NDK, it is written as if we all run Linux and presumes we all understand what these obscure tools are. My comments and questions appear in Italics if somone who knows unix and windows would translate for google that would be great! Android NDK Installation Introduction: Please read docs/OVERVIEW.TXT to understand what the Android NDK is and is not. This file gives instructions on how to properly setup your NDK. I. Requirements: The Android NDK currently requires a Linux, OS X or Windows host operating system. Windows users will need to install Cygwin (http://www.cygwin.com) to use it. Note that running the NDK under MSys is not supported. You will need to have the Android SDK and its dependencies installed. The NDK cannot generate final application packages (.apk files), only the shared library files that can go into them. IMPORTANT: The Android NDK can only be used to target system images using the Cupcake (1.5) or later releases of the platform. This is due to subtle toolchain and ABI related changed that make it incompatible with 1.0 and 1.1 system images. The NDK requires GNU Make 3.81 or later being available on your development system. Earlier versions of GNU Make might work but have not been tested. You can check this by running 'make -v' from the command-line. The output should look like: GNU Make 3.81 Copyright (C) 2006 Free Software Foundation, Inc. ... On certain systems, GNU Make might be available through a different command like 'gmake' or 'gnumake'. For these systems, replace 'make' by the appropriate command when invoking the NDK build system as described in the documentation. Great some strange thing called gnu make.. if your not going to tell me what it does maybe you then at least you could give me a URL to it? The NDK also requires a Nawk or GNU Awk executable being available on your development system. Note that the original 'awk' program doesn't implement the 'match' and 'substr' functions used by the NDK build system. Ok another tool, with 1 of 2 possible names, but not the third... and again where should i download this?? On Windows, you will need to install a recent release of Cygwin to use the NDK. See http://www.cygwin.com for instructions. Woohoo a URL! download took about a day because these install instructions do not specify what parts to download. II. Preparing your installation prebuilt cross-toolchain binaries: After installing and unarchiving the NDK, you will need to run the following command from the root folder: build/host-setup.sh hello? windows dont run nothing but .exe .com or .dll, just tell me how you want me to run it.. This will test your setup and make sure the NDK can work properly. Nothing is said about where any of these things need to be installed to (what directory)

  Read the article

• Issue with XSL Criteria

  - by Rachel

  I am using the below piece of XSL to select the id of the text nodes whose content has a given index. This index value in input will be relative to a spcified node whose id value is known. The criteria to select the text node is, The text node content should contain a index say 'i' relative to node say 'n' whose id value i know. 'i' and 'id of n' is got as index and nodeName from the input param as seen in the xsl. Node 'd1e5' has the text content whose index ranges from 1 to 33. When i give an index value greater than 33 i want the below criteria to fail but it does not, [sum((preceding::text(), .)[normalize-space()][. >> //*[@id=$nodeName]]/string-length(.)) ge $index] Input xml: <?xml version="1.0" encoding="UTF-8"?> <html xmlns="http://www.w3.org/1999/xhtml" id="d1e1"> <head id="d1e3"> <meta http-equiv="Content-Type" content="text/html; charset=UTF-8" /> <title id="d1e5">Every document must have a title</title> </head> <body id="d1e9"> <h1 id="d1e11" align="center">Very Important Heading</h1> <p id="d1e13">Since this is just a sample, I won't put much text here.</p> </body> </html> XSL code used: <xsl:stylesheet xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:xsd="http://www.w3.org/2001/XMLSchema" exclude-result-prefixes="xsd" version="2.0"> <xsl:param name="insert-file" as="node()+"> <insert-data><data index="1" nodeName="d1e5"></data><data index="34" nodeName="d1e5"></data></insert-data> </xsl:param> <xsl:param name="nodeName" as="xsd:string" /> <xsl:variable name="main-root" as="document-node()" select="/"/> <xsl:variable name="insert-data" as="element(data)*"> <xsl:for-each select="$insert-file/insert-data/data"> <xsl:sort select="xsd:integer(@index)"/> <xsl:variable name="index" select="xsd:integer(@index)" /> <xsl:variable name="nodeName" select="@nodeName" /> <data text-id="{generate-id($main-root/descendant::text()[sum((preceding::text(), .)[normalize-space()][. >> //*[@id=$nodeName]]/string-length(.)) ge $index][1])}"> </data> </xsl:for-each> </xsl:variable> <xsl:template match="/"> <Output> <xsl:copy-of select="$insert-data" /> </Output> </xsl:template> </xsl:stylesheet> Actual output: <?xml version="1.0" encoding="UTF-8"?> <Output> <data text-id="d1t8"/> <data text-id="d1t14"/> </Output> Expected output: <?xml version="1.0" encoding="UTF-8"?> <Output> <data text-id="d1t8"/> </Output> This solution works fine if index lies between 1 and 33. Any index value greater that 33 causes incorrect text nodes to get selected. I could not understand why the text node 'd1t14' is getting selected. Please share your thoughts.

  Read the article

• How do I make these fields autopopulate from the database?

  - by dmanexe

  I have an array, which holds values like this: $items_pool = Array ( [0] => Array ( [id] => 1 [quantity] => 1 ) [1] => Array ( [id] => 2 [quantity] => 1 ) [2] => Array ( [id] => 72 [quantity] => 6 ) [3] => Array ( [id] => 4 [quantity] => 1 ) [4] => Array ( [id] => 5 [quantity] => 1 ) [5] => Array ( [id] => 7 [quantity] => 1 ) [6] => Array ( [id] => 8 [quantity] => 1 ) [7] => Array ( [id] => 9 [quantity] => 1 ) [8] => Array ( [id] => 19 [quantity] => 1 ) [9] => Array ( [id] => 20 [quantity] => 1 ) [10] => Array ( [id] => 22 [quantity] => 1 ) [11] => Array ( [id] => 29 [quantity] => 0 ) ) Next, I have a form that I am trying to populate. It loops through the item database, prints out all the possible items, and checks the ones that are already present in $items_pool. <?php foreach ($items['items_poolpackage']->result() as $item): ?> <input type="checkbox" name="measure[<?=$item->id?>][checkmark]" value="<?=$item->id?>"> <?php endforeach; ?> I know what logically I'm trying to accomplish here, but I can't figure out the programming. What I'm looking for, written loosely is something like this (not real code): <input type="checkbox" name="measure[<?=$item->id?>][checkmark]" value="<?=$item->id?>" <?php if ($items_pool['$item->id']) { echo "SELECTED"; } else { }?>> Specifically this conditional loop through the array, through all the key values (the ID) and if there's a match, the checkbox is selected. <?php if ($items_pool['$item->id']) { echo "SELECTED"; } else { }?> I understand from a loop structured like this that it may mean a lot of 'extra' processing. TL;DR - I need to echo within a loop if the item going through the loop exists within another array.

  Read the article

• Help with this code.

  - by karthick6891

  Heading ##Hey guys i need help with this code.The short version is,i have to do match the follwing by using drag and drop in jquery and later i need to show a message whether it is right or wrong. var output = "Wrong"; var old_item ; var new_item ; var newObjArray=[]; $(function() { var $gallery = $('.gallery'), $trash = $('.trash'); $('div',$gallery).draggable({ revert: 'invalid', containment: 'document', helper: 'clone', cursor: 'move', }); // let the trash be droppable, accepting the gallery items $trash.droppable({ //accept: '#gallery div', //activeClass: 'ui-state-highlight', tolerance: 'touch', drop: function(ev, ui) { new_item = ui.draggable; $(this).droppable("option","activeClass",'.ui-state-highlight'); if(contains(newObjArray,ui.draggable)) { newObjArray.pop(ui.draggable); } newObjArray.push(ui.draggable); deleteImage(ui.draggable,$(this)); } }); // let the gallery be droppable as well, accepting items from the trash $gallery.droppable({ //accept: '#trash li', activeClass: 'custom-state-active', drop: function(ev, ui) { recycleImage(ui.draggable); } }); // image deletion function function deleteImage($item,element) { var $list; $item.fadeOut(10,function() { if($(".ui-widget-content", element).length <1){ old_item = $item; $list = $('<div class="gallery ui-helper-reset"/>').appendTo(element); //$('ul',$trash).length ? $('ul',$trash) : $('<ul class="gallery ui-helper-reset"/>').appendTo($trash); $item.appendTo($list).fadeIn(10); } else{ recycleImage($(".ui-widget-content",element)); $list = $('<div class="gallery ui-helper-reset"/>').appendTo(element); $item.appendTo($list).fadeIn(10); old_item = $item; } }); } //check for given answer // image recycle function function recycleImage($item) { $item.fadeOut(10,function() { $item.find("img").end().appendTo($gallery).fadeIn(10); }); } // image preview function, demonstrating the ui.dialog used as a modal window }); function checkOrder(){ if(newObjArray==null){ } else if(newObjArray!=null){ if(newObjArray[0].attr("id")=="5"&& newObjArray[1].attr("id")=="1" && newObjArray[2].attr("id")=="3" && newObjArray[3].attr("id")=="2" && newObjArray[4].attr("id")=="4"){ parent.parent.increaseCorrectA(); } else{ parent.parent.increaseWrongA(); } } } function contains(a, obj) { var i = a.length; while (i--) { if (a[i] === obj) { return true; } } return false; } I am calling the function checkOrder() from the html page after the matching of items is over.What happens here is i have just stored the user responses on the draggable over droppable in an array,based on it's position.It is a bad practice cause,i am saying whether it's right or wrong through its position in the array.The only thing i can do is get the draggable's id present in the droppable.But i dont know how to get that inside the function checkOrder().Any ideas please?

  Read the article

• Remote Desktop Services Gateway Issue

  - by AVandelay05

  Alright fellow techies here's the rundown. I have installed Server 2008 r2 Remote Dekstop Services on a VM in my network. I installed the following RD role services: RD Session Host, Licensing, Connection Broker, Gateway, Web Access. When I set things up originally, the gateway server and RDWeb worked as it should locally. After getting things running locally (remoteserver.domainname.local) I wanted to test things externally. From the outside, I couldn't get things running (meaning I could connect to rdweb access externally, but when I tried to run an app I would get the message "can't connect/find computer"). Here's my setup for external access The VM has every RD Services role services installed on it, meaning it acts as gateway, rd web access, session host, licensing, the whole bit. I made a self-signed certificate on the gateway server (gateway.domainname.net is the cert name). Internally, I have a secondary forward-lookup zone called domainname.net with an A record gateway pointing to the local IP of the gateway server. On our public DNS (domainname.net) I have an A record gateway. This is to access the RDWeb externally. In IIS I have the following authentication settings RDWeb: All disabled except for anonymous authentication Rpc: All disabled except for basic and windows RpcWithCert: All disbled except for windows authentication I have the necessary web access config in our sonicwall tz210 (https and rdp, external ip pointing to local ip of rds server) RAP and CAP have the correct user and computer groups, authentication, and allowed devices After all of this, here's what happens accessing externally. I can login correctly to RDWeb Access (I've tried a bogus login, I can't login to it so that's working properly). I see the Apps for use. I click on an app, click connect, the credential window opens, I put in the correct user creds, it tries to connect to the gateway server, but then the cred window comes back in view. I tried to reach a limit of failed logins, but never reached one, haha. So from the same external client machine I try to connect to the gateway through a Remote Desktop connection. I put in the correct gateway settings in the RD window, try to connect and get the same results as I did in RDWeb access. I checked the event logs on the RD Services machine and saw the following event IDs around the time I tried to login externally: ID 6037 with the message "The program svchost.exe, with the assigned process ID 2168, could not authenticate locally by using the target name host/gateway.domainname.net. The target name used is not valid. A target name should refer to one of the local computer names, for example, the DNS host name. Try a different target name." ID 10 RADWebAccess "RD Web Access was unable to access gateway.domainname.net, which is the server that is specified as running the RemoteApp and Desktop Connection Management service. Ensure that the computer account of the RD Web Access server is a member of the TS Web Access Computers security group on gateway.domainname.net" ID 4625 "An account failed to log on. Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: Administrator Account Domain: gateway.domainname.net Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc000006a Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: USER-LAPTOP Source Network Address: External IP Source Port: 63125 Detailed Authentication Information: Logon Process: NtLmSsp Authentication Package: NTLM Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols." I don't think the VM has a null SID. The SID of the VM and it's physical host have different SIDS. I can access the blank page for rpc externally using the external gateway name. It seems like authentication is a problem. Also, is it a problem that the external name of the gateway server doesn't match the local name? The external name (which the cert is based on) is gateway.domainname.net and the internal name is remoteserver.domainname.local. That's the only thing I can think of that would be the problem, but the external name has to be different from the local right? Internally, I ping gateway.domainname.net and it gives me the correct local IP of the server. Now, there isn't an actual computer name in AD, but I don't know how I would achieve that? I hope I've been clear....any help would be appreciated. I think I'm close to achieving this. :)

  Read the article

• Insert Error:CREATE DATABASE permission denied in database 'master'. cannot attach the file

  - by user1300580

  i have a register page on my website I am creating and it saves the data entered by the user into a database however when I click the register button i am coming across the following error: Insert Error:CREATE DATABASE permission denied in database 'master'. Cannot attach the file 'C:\Users\MyName\Documents\MyName\Docs\Project\SJ\App_Data\SJ-Database.mdf' as database 'SJ-Database'. These are my connection strings: <connectionStrings> <add name="ApplicationServices" connectionString="data source=.\SQLEXPRESS;Integrated Security=SSPI;AttachDBFilename=|DataDirectory|\aspnetdb.mdf;User Instance=true" providerName="System.Data.SqlClient"/> <add name="MyConsString" connectionString="data source=.\SQLEXPRESS;Integrated Security=SSPI;AttachDBFilename=|DataDirectory|SJ-Database.mdf; Initial Catalog=SJ-Database; Integrated Security=SSPI;" providerName="System.Data.SqlClient" /> </connectionStrings> Register page code: using System; using System.Collections.Generic; using System.Linq; using System.Web; using System.Web.UI; using System.Web.UI.WebControls; using System.Data; using System.Data.SqlClient; public partial class About : System.Web.UI.Page { protected void Page_Load(object sender, EventArgs e) { } public string GetConnectionString() { //sets the connection string from your web config file "ConnString" is the name of your Connection String return System.Configuration.ConfigurationManager.ConnectionStrings["MyConsString"].ConnectionString; } private void ExecuteInsert(string name, string gender, string age, string address, string email) { SqlConnection conn = new SqlConnection(GetConnectionString()); string sql = "INSERT INTO Register (Name, Gender, Age, Address, Email) VALUES " + " (@Name,@Gender,@Age,@Address,@Email)"; try { conn.Open(); SqlCommand cmd = new SqlCommand(sql, conn); SqlParameter[] param = new SqlParameter[6]; //param[0] = new SqlParameter("@id", SqlDbType.Int, 20); param[0] = new SqlParameter("@Name", SqlDbType.VarChar, 50); param[1] = new SqlParameter("@Gender", SqlDbType.Char, 10); param[2] = new SqlParameter("@Age", SqlDbType.Int, 100); param[3] = new SqlParameter("@Address", SqlDbType.VarChar, 50); param[4] = new SqlParameter("@Email", SqlDbType.VarChar, 50); param[0].Value = name; param[1].Value = gender; param[2].Value = age; param[3].Value = address; param[4].Value = email; for (int i = 0; i < param.Length; i++) { cmd.Parameters.Add(param[i]); } cmd.CommandType = CommandType.Text; cmd.ExecuteNonQuery(); } catch (System.Data.SqlClient.SqlException ex) { string msg = "Insert Error:"; msg += ex.Message; throw new Exception(msg); } finally { conn.Close(); } } protected void cmdRegister_Click(object sender, EventArgs e) { if (txtRegEmail.Text == txtRegEmailCon.Text) { //call the method to execute insert to the database ExecuteInsert(txtRegName.Text, txtRegAge.Text, ddlRegGender.SelectedItem.Text, txtRegAddress.Text, txtRegEmail.Text); Response.Write("Record was successfully added!"); ClearControls(Page); } else { Response.Write("Email did not match"); txtRegEmail.Focus(); } } public static void ClearControls(Control Parent) { if (Parent is TextBox) { (Parent as TextBox).Text = string.Empty; } else { foreach (Control c in Parent.Controls) ClearControls(c); } } }

  Read the article

• Longitudinal Redundancy Check fails

  - by PaulH

  I have an application that decodes data from a magnetic stripe reader. But, I'm having difficulty getting my calculated LRC check byte to match the one on the cards. If I were to grab 3 cards each with 3 tracks, I would guess the algorithm below would work on 4 of the 9 tracks in those cards. The algorithm I'm using looks like this (C#): private static char GetLRC(string s, int start, int end) { int result = 0; for (int i = start; i <= end; i++) { result ^= Convert.ToByte(s[i]); } return Convert.ToChar(result); } This is an example of track 3 data that fails the check. On this card, track 2 matched, but track 1 also failed. 0 1 2 3 4 5 6 7 8 9 A B C D E F 00 3 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 10 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 7 20 7 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 30 8 8 8 9 9 9 9 9 9 9 9 9 9 0 0 0 40 0 0 0 0 0 0 0 1 2 3 4 1 1 1 1 1 50 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 60 3 3 3 3 3 3 3 3 The sector delimiter is ';' and it ends with a '?'. The LRC byte from this track is 0x30. Unfortunately, the algorithm above computes an LRC of 0x00 per the following calculation (apologies for its length. I want to be thorough): 00 ^ 3b = 3b ';' 3b ^ 33 = 08 08 ^ 34 = 3c 3c ^ 34 = 08 08 ^ 34 = 3c 3c ^ 34 = 08 08 ^ 34 = 3c 3c ^ 34 = 08 08 ^ 34 = 3c 3c ^ 34 = 08 08 ^ 34 = 3c 3c ^ 34 = 08 08 ^ 35 = 3d 3d ^ 35 = 08 08 ^ 35 = 3d 3d ^ 35 = 08 08 ^ 35 = 3d 3d ^ 35 = 08 08 ^ 35 = 3d 3d ^ 35 = 08 08 ^ 35 = 3d 3d ^ 35 = 08 08 ^ 36 = 3e 3e ^ 36 = 08 08 ^ 36 = 3e 3e ^ 36 = 08 08 ^ 36 = 3e 3e ^ 36 = 08 08 ^ 36 = 3e 3e ^ 36 = 08 08 ^ 36 = 3e 3e ^ 36 = 08 08 ^ 37 = 3f 3f ^ 37 = 08 08 ^ 37 = 3f 3f ^ 37 = 08 08 ^ 37 = 3f 3f ^ 37 = 08 08 ^ 37 = 3f 3f ^ 37 = 08 08 ^ 37 = 3f 3f ^ 37 = 08 08 ^ 38 = 30 30 ^ 38 = 08 08 ^ 38 = 30 30 ^ 38 = 08 08 ^ 38 = 30 30 ^ 38 = 08 08 ^ 38 = 30 30 ^ 38 = 08 08 ^ 38 = 30 30 ^ 38 = 08 08 ^ 39 = 31 31 ^ 39 = 08 08 ^ 39 = 31 31 ^ 39 = 08 08 ^ 39 = 31 31 ^ 39 = 08 08 ^ 39 = 31 31 ^ 39 = 08 08 ^ 39 = 31 31 ^ 39 = 08 08 ^ 30 = 38 38 ^ 30 = 08 08 ^ 30 = 38 38 ^ 30 = 08 08 ^ 30 = 38 38 ^ 30 = 08 08 ^ 30 = 38 38 ^ 30 = 08 08 ^ 30 = 38 38 ^ 30 = 08 08 ^ 31 = 39 39 ^ 32 = 0b 0b ^ 33 = 38 38 ^ 34 = 0c 0c ^ 31 = 3d 3d ^ 31 = 0c 0c ^ 31 = 3d 3d ^ 31 = 0c 0c ^ 31 = 3d 3d ^ 31 = 0c 0c ^ 31 = 3d 3d ^ 31 = 0c 0c ^ 31 = 3d 3d ^ 31 = 0c 0c ^ 32 = 3e 3e ^ 32 = 0c 0c ^ 32 = 3e 3e ^ 32 = 0c 0c ^ 32 = 3e 3e ^ 32 = 0c 0c ^ 32 = 3e 3e ^ 32 = 0c 0c ^ 32 = 3e 3e ^ 32 = 0c 0c ^ 33 = 3f 3f ^ 33 = 0c 0c ^ 33 = 3f 3f ^ 33 = 0c 0c ^ 33 = 3f 3f ^ 33 = 0c 0c ^ 33 = 3f 3f ^ 33 = 0c 0c ^ 33 = 3f 3f ^ 3f = 00 '?' If anybody can point out how to fix my algorithm, I would appreciate it. Thanks, PaulH

  Read the article

• One letter game problem?

  - by Alex K

  Recently at a job interview I was given the following problem: Write a script capable of running on the command line as python It should take in two words on the command line (or optionally if you'd prefer it can query the user to supply the two words via the console). Given those two words: a. Ensure they are of equal length b. Ensure they are both words present in the dictionary of valid words in the English language that you downloaded. If so compute whether you can reach the second word from the first by a series of steps as follows a. You can change one letter at a time b. Each time you change a letter the resulting word must also exist in the dictionary c. You cannot add or remove letters If the two words are reachable, the script should print out the path which leads as a single, shortest path from one word to the other. You can /usr/share/dict/words for your dictionary of words. My solution consisted of using breadth first search to find a shortest path between two words. But apparently that wasn't good enough to get the job :( Would you guys know what I could have done wrong? Thank you so much. import collections import functools import re def time_func(func): import time def wrapper(*args, **kwargs): start = time.time() res = func(*args, **kwargs) timed = time.time() - start setattr(wrapper, 'time_taken', timed) return res functools.update_wrapper(wrapper, func) return wrapper class OneLetterGame: def __init__(self, dict_path): self.dict_path = dict_path self.words = set() def run(self, start_word, end_word): '''Runs the one letter game with the given start and end words. ''' assert len(start_word) == len(end_word), \ 'Start word and end word must of the same length.' self.read_dict(len(start_word)) path = self.shortest_path(start_word, end_word) if not path: print 'There is no path between %s and %s (took %.2f sec.)' % ( start_word, end_word, find_shortest_path.time_taken) else: print 'The shortest path (found in %.2f sec.) is:\n=> %s' % ( self.shortest_path.time_taken, ' -- '.join(path)) def _bfs(self, start): '''Implementation of breadth first search as a generator. The portion of the graph to explore is given on demand using get_neighboors. Care was taken so that a vertex / node is explored only once. ''' queue = collections.deque([(None, start)]) inqueue = set([start]) while queue: parent, node = queue.popleft() yield parent, node new = set(self.get_neighbours(node)) - inqueue inqueue = inqueue | new queue.extend([(node, child) for child in new]) @time_func def shortest_path(self, start, end): '''Returns the shortest path from start to end using bfs. ''' assert start in self.words, 'Start word not in dictionnary.' assert end in self.words, 'End word not in dictionnary.' paths = {None: []} for parent, child in self._bfs(start): paths[child] = paths[parent] + [child] if child == end: return paths[child] return None def get_neighbours(self, word): '''Gets every word one letter away from the a given word. We do not keep these words in memory because bfs accesses a given vertex only once. ''' neighbours = [] p_word = ['^' + word[0:i] + '\w' + word[i+1:] + '$' for i, w in enumerate(word)] p_word = '|'.join(p_word) for w in self.words: if w != word and re.match(p_word, w, re.I|re.U): neighbours += [w] return neighbours def read_dict(self, size): '''Loads every word of a specific size from the dictionnary into memory. ''' for l in open(self.dict_path): l = l.decode('latin-1').strip().lower() if len(l) == size: self.words.add(l) if __name__ == '__main__': import sys if len(sys.argv) not in [3, 4]: print 'Usage: python one_letter_game.py start_word end_word' else: g = OneLetterGame(dict_path = '/usr/share/dict/words') try: g.run(*sys.argv[1:]) except AssertionError, e: print e

  Read the article

• overloaded stream insetion operator with a vector

  - by julz666

  hi, i'm trying to write an overloaded stream insertion operator for a class who's only member is a vector. i dont really know what i'm doing. (lets make that clear) it's a vector of "Points" which is a struct containing two doubles. i figure what i want is to insert user input (a bunch of doubles) into a stream that i then send to a modifier method? i keep working off other stream insertion examples such as... std::ostream& operator<< (std::ostream& o, Fred const& fred) { return o << fred.i_; } but when i try a similar..... istream & operator >> (istream &inStream, Polygon &vertStr) { inStream >> ws; inStream >> vertStr.vertices; return inStream; } i get an error "no match for operator etc etc. if i leave off the .vertices it compiles but i figure it's not right? (vertices is the name of my vector ) and even if it is right, i dont actually know what syntax to use in my driver to use it? also not %100 on what my modifier method needs to look like. here's my Polygon class //header #ifndef POLYGON_H #define POLYGON_H #include "Segment.h" #include <vector> class Polygon { friend std::istream & operator >> (std::istream &inStream, Polygon &vertStr); public: //Constructor Polygon(const Point &theVerts); //Default Constructor Polygon(); //Copy Constructor Polygon(const Polygon &polyCopy); //Accessor/Modifier methods inline std::vector<Point> getVector() const {return vertices;} //Return number of Vector elements inline int sizeOfVect() const {return (int) vertices.capacity();} //add Point elements to vector inline void setVertices(const Point &theVerts){vertices.push_back (theVerts);} private: std::vector<Point> vertices; }; #endif //Body using namespace std; #include "Polygon.h" // Constructor Polygon::Polygon(const Point &theVerts) { vertices.push_back (theVerts); } //Copy Constructor Polygon::Polygon(const Polygon &polyCopy) { vertices = polyCopy.vertices; } //Default Constructor Polygon::Polygon(){} istream & operator >> (istream &inStream, Polygon &vertStr) { inStream >> ws; inStream >> vertStr; return inStream; } any help greatly appreciated, sorry to be so vague, a lecturer has just kind of given us a brief example of stream insertion then left us on our own thanks. oh i realise there are probably many other problems that need fixing

  Read the article

• Flash Media Server Streaming: Content Protection

  - by dbemerlin

  Hi, i have to implement flash streaming for the relaunch of our video-on-demand system but either because i haven't worked with flash-related systems before or because i'm too stupid i cannot get the system to work as it has to. We need: Per file & user access control with checks on a WebService every minute if the lease time ran out mid-stream: cancelling the stream rtmp streaming dynamic bandwidth checking Video Playback with Flowplayer (existing license) I've got the streaming and bandwidth check working, i just can't seem to get the access control working. I have no idea how i know which file is played back or how i can play back a file depending on a key the user has entered. Server-Side Code (main.asc): application.onAppStart = function() { trace("Starting application"); this.payload = new Array(); for (var i=0; i < 1200; i++) { this.payload[i] = Math.random(); //16K approx } } application.onConnect = function( p_client, p_autoSenseBW ) { p_client.writeAccess = ""; trace("client at : " + p_client.uri); trace("client from : " + p_client.referrer); trace("client page: " + p_client.pageUrl); // try to get something from the query string: works var i = 0; for (i = 0; i < p_client.uri.length; ++i) { if (p_client.uri[i] == '?') { ++i; break; } } var loadVars = new LoadVars(); loadVars.decode(p_client.uri.substr(i)); trace(loadVars.toString()); trace(loadVars['foo']); // And accept the connection this.acceptConnection(p_client); trace("accepted!"); //this.rejectConnection(p_client); // A connection from Flash 8 & 9 FLV Playback component based client // requires the following code. if (p_autoSenseBW) { p_client.checkBandwidth(); } else { p_client.call("onBWDone"); } trace("Done connecting"); } application.onDisconnect = function(client) { trace("client disconnecting!"); } Client.prototype.getStreamLength = function(p_streamName) { trace("getStreamLength:" + p_streamName); return Stream.length(p_streamName); } Client.prototype.checkBandwidth = function() { application.calculateClientBw(this); } application.calculateClientBw = function(p_client) { /* lots of lines copied from an adobe sample, appear to work */ } Client-Side Code: <head> <script type="text/javascript" src="flowplayer-3.1.4.min.js"></script> </head> <body> <a class="rtmp" href="rtmp://xx.xx.xx.xx/vod_project/test_flv.flv" style="display: block; width: 520px; height: 330px" id="player"> </a> <script> $f( "player", "flowplayer-3.1.5.swf", { clip: { provider: 'rtmp', autoPlay: false, url: 'test_flv' }, plugins: { rtmp: { url: 'flowplayer.rtmp-3.1.3.swf', netConnectionUrl: 'rtmp://xx.xx.xx.xx/vod_project?foo=bar' } } } ); </script> </body> My first Idea was to get a key from the Query String, ask the web service about which file and user that key is for and play the file but i can't seem to find out how to play a file from server side. My second idea was to let flowplayer play a file, pass the key as query string and if the filename and key don't match then reject the connection but i can't seem to find out which file it's currently playing. The only remaining idea i have is: create a list of all files the user is allowed to open and set allowReadAccess or however it was called to allow those files, but that would be clumsy due to the current infrastructure. Any hints? Thanks.

  Read the article

• Spring Security and the Synchronizer Token J2EE pattern, problem when authentication fails.

  - by dfuse

  Hey, we are using Spring Security 2.0.4. We have a TransactionTokenBean which generates a unique token each POST, the bean is session scoped. The token is used for the duplicate form submission problem (and security). The TransactionTokenBean is called from a Servlet filter. Our problem is the following, after a session timeout occured, when you do a POST in the application Spring Security redirects to the logon page, saving the original request. After logging on again the TransactionTokenBean is created again, since it is session scoped, but then Spring forwards to the originally accessed url, also sending the token that was generated at that time. Since the TransactionTokenBean is created again, the tokens do not match and our filter throws an Exception. I don't quite know how to handle this elegantly, (or for that matter, I can't even fix it with a hack), any ideas? This is the code of the TransactionTokenBean: public class TransactionTokenBean implements Serializable { public static final int TOKEN_LENGTH = 8; private RandomizerBean randomizer; private transient Logger logger; private String expectedToken; public String getUniqueToken() { return expectedToken; } public void init() { resetUniqueToken(); } public final void verifyAndResetUniqueToken(String actualToken) { verifyUniqueToken(actualToken); resetUniqueToken(); } public void resetUniqueToken() { expectedToken = randomizer.getRandomString(TOKEN_LENGTH, RandomizerBean.ALPHANUMERICS); getLogger().debug("reset token to: " + expectedToken); } public void verifyUniqueToken(String actualToken) { if (getLogger().isDebugEnabled()) { getLogger().debug("verifying token. expected=" + expectedToken + ", actual=" + actualToken); } if (expectedToken == null || actualToken == null || !isValidToken(actualToken)) { throw new IllegalArgumentException("missing or invalid transaction token"); } if (!expectedToken.equals(actualToken)) { throw new InvalidTokenException(); } } private boolean isValidToken(String actualToken) { return StringUtils.isAlphanumeric(actualToken); } public void setRandomizer(RandomizerBean randomizer) { this.randomizer = randomizer; } private Logger getLogger() { if (logger == null) { logger = Logger.getLogger(TransactionTokenBean.class); } return logger; } } and this is the Servlet filter (ignore the Ajax stuff): public class SecurityFilter implements Filter { static final String AJAX_TOKEN_PARAM = "ATXTOKEN"; static final String TOKEN_PARAM = "TXTOKEN"; private WebApplicationContext webApplicationContext; private Logger logger = Logger.getLogger(SecurityFilter.class); public void init(FilterConfig config) { setWebApplicationContext(WebApplicationContextUtils.getWebApplicationContext(config.getServletContext())); } public void destroy() { } public void doFilter(ServletRequest req, ServletResponse response, FilterChain chain) throws IOException, ServletException { HttpServletRequest request = (HttpServletRequest) req; if (isPostRequest(request)) { if (isAjaxRequest(request)) { log("verifying token for AJAX request " + request.getRequestURI()); getTransactionTokenBean(true).verifyUniqueToken(request.getParameter(AJAX_TOKEN_PARAM)); } else { log("verifying and resetting token for non-AJAX request " + request.getRequestURI()); getTransactionTokenBean(false).verifyAndResetUniqueToken(request.getParameter(TOKEN_PARAM)); } } chain.doFilter(request, response); } private void log(String line) { if (logger.isDebugEnabled()) { logger.debug(line); } } private boolean isPostRequest(HttpServletRequest request) { return "POST".equals(request.getMethod().toUpperCase()); } private boolean isAjaxRequest(HttpServletRequest request) { return request.getParameter("AJAXREQUEST") != null; } private TransactionTokenBean getTransactionTokenBean(boolean ajax) { return (TransactionTokenBean) webApplicationContext.getBean(ajax ? "ajaxTransactionTokenBean" : "transactionTokenBean"); } void setWebApplicationContext(WebApplicationContext context) { this.webApplicationContext = context; } }

  Read the article

• Best way to get back to using the power of lxml after having to use a regex to find something in an

  - by PyNEwbie

  I am trying to rip some text out of a large number of html documents (numbers in the hundreds of thousands). The documents are really forms but they are prepared by a very large group of different organizations so there is significant variation in how they create the document. For example, the documents are divided into chapters. I might want to extract the contents of Chapter 5 from every document so I can analyze the content of the chapter. Initially I thought this would be easy but it turns out that the authors might use a set of non-nested tables throughout the document to hold the content so that Chapter n could be displayed using td tags inside a table. Or they might use other elements such as p tags H tags, div tags or any other block level element. After trying repeatedly to use lxml to help me identify the beginning and end of each chapter I have determined that it is a lot cleaner to use a regular expression because in every case, no matter what the enclosing html element is the chapter label is always in the form of >Chapter # It is a little more complicated in that there might be some white space or non-breaking space represented in different ways (  or   or just spaces). Nonetheless it was trivial to write a regular expression to identify the beginning of each section. (The beginning of one section is the end of the previous section.) But now I want to use lxml to get the text out. My thought is that I have really no choice but to walk along my string to find the close tag for the element that encloses the text I am using to find the relevant section. That is here is one example where the element holding the Chapter name is a div <div style="DISPLAY: block; MARGIN-LEFT: 0pt; TEXT-INDENT: 0pt; MARGIN-RIGHT: 0pt" align="left"><font style="DISPLAY: inline; FONT-WEIGHT: bold; FONT-SIZE: 10pt; FONT-FAMILY: Times New Roman">Chapter 1.&#160;&#160;&#160;Our Beginnings.</font></div> So I am imagining that I would begin at the location where I found the match for chapter 1 and set up a regular expressions to find the next </div|</td|</p|</h1 . . . So at this point I have identified the type of element holding my chapter heading I can use the same logic to find all of the text that is within that element that is set up a regular expression to help me mark from >Chapter 1.&#160;&#160;&#160;Our Beginnings.< So I have identified where my Chapter 1 begins I can do the same for chapter 2 (which is where Chapter 1 ends) Now I am imagining that I am going to snip the document beginning at the opening of the element that I identified as the element the indicates where chapter 1 begins and ending just before the opening of the element that I identified as the element that indicates where Chapter 2 begins. The string that I have identified will then be fed to lxml to use its power to get the content. I am going to all of this trouble because I have read over and over - never use a regular expression to extract content from html documents and I have not hit on a way to be as accurate with lxml to identify the starting and ending locations for the text I want to extract. For example, I can never be certain that the subtitle of Chapter 1 is Our Beginnings it could be Our Red Canary. Let me say that I spent two solid days trying with lxml to be confident that I had the beginning and ending elements and I could only be accurate <60% of the time but a very short regular expression has given me better than 95% success. I have a tendency to make things more complicated than necessary so I am wondering if anyone has seen or solved a similar problems and if they had an approach (not the details mind you) that they would like to offer.

  Read the article

• XSLT: a variation on the pagination problem

  - by MarcoS

  I must transform some XML data into a paginated list of fields. Here is an example. Input XML: <?xml version="1.0" encoding="UTF-8"?> <data> <books> <book title="t0"/> <book title="t1"/> <book title="t2"/> <book title="t3"/> <book title="t4"/> </books> <library name="my library"/> </data> Desired output: <?xml version="1.0" encoding="UTF-8"?> <pages> <page number="1"> <field name="library_name" value="my library"/> <field name="book_1" value="t0"/> <field name="book_2" value="t1"/> </page> <page number="2"> <field name="book_1" value="t2"/> <field name="book_2" value="t3"/> </page> <page number="3"> <field name="book_1" value="t4"/> </page> </pages> In the above example I assume that I want at most 2 fields named book_n (with n ranging between 1 and 2) per page. Tags <page> must have an attribute number. Finally, the field named library_name must appear only the first <page>. Here is my current solution using XSLT: <?xml version="1.0" encoding="UTF-8"?> <xsl:stylesheet xmlns:xsl="http://www.w3.org/1999/XSL/Transform" version="2.0" exclude-result-prefixes="trx xs"> <xsl:output method="xml" indent="yes" omit-xml-declaration="no" /> <xsl:variable name="max" select="2"/> <xsl:template match="//books"> <xsl:for-each-group select="book" group-ending-with="*[position() mod $max = 0]"> <xsl:variable name="pageNum" select="position()"/> <page number="{$pageNum}"> <xsl:for-each select="current-group()"> <xsl:variable name="idx" select="if (position() mod $max = 0) then $max else position() mod $max"/> <field value="{@title}"> <xsl:attribute name="name">book_<xsl:value-of select="$idx"/> </xsl:attribute> </field> </xsl:for-each> <xsl:if test="$pageNum = 1"> <xsl:call-template name="templateFor_library"/> </xsl:if> </page> </xsl:for-each-group> </xsl:template> <xsl:template name="templateFor_library"> <xsl:for-each select="//library"> <field name="library_name" value="{@name}" /> </xsl:for-each> </xsl:template> </xsl:stylesheet> Is there a better/simpler way to perform this transformation?

  Read the article

• Can't access shared drive when connecting over VPN

  - by evolvd

  I can ping all network devices but it doesn't seem that DNS is resolving their hostnames. ipconfig/ all is showing that I am pointing to the correct dns server. I can "ping "dnsname"" and it will resolve but it wont resolve any other names. Split tunnel is set up so outside DNS is resolving fine So one issue might be DNS but I have the IP address of the server share so I figure I could just get to it that way. example: \10.0.0.1\ well I can't get to it that way either and I get "the specified network name is no longer available" I can ping it but I can't open the share. Below is the ASA config : ASA Version 8.2(1) ! hostname KG-ASA domain-name example.com names ! interface Vlan1 nameif inside security-level 100 ip address 10.0.0.253 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns domain-lookup outside dns server-group DefaultDNS name-server 10.0.0.101 domain-name blah.com access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 10000 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 8333 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 902 access-list SPLIT-TUNNEL-VPN standard permit 10.0.0.0 255.0.0.0 access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool IPSECVPN-POOL 10.0.1.2-10.0.1.50 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 10000 10.0.0.101 10000 netmask 255.255.255.255 static (inside,outside) tcp interface 8333 10.0.0.101 8333 netmask 255.255.255.255 static (inside,outside) tcp interface 902 10.0.0.101 902 netmask 255.255.255.255 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication enable console LOCAL aaa authentication http console LOCAL aaa authentication serial console LOCAL aaa authentication ssh console LOCAL aaa authentication telnet console LOCAL http server enable http 10.0.0.0 255.255.0.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set myset esp-aes esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map dynmap 1 set transform-set myset crypto dynamic-map dynmap 1 set reverse-route crypto map IPSEC-MAP 65535 ipsec-isakmp dynamic dynmap crypto map IPSEC-MAP interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption aes hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 0.0.0.0 0.0.0.0 inside ssh 70.60.228.0 255.255.255.0 outside ssh 74.102.150.0 255.255.254.0 outside ssh 74.122.164.0 255.255.252.0 outside ssh timeout 5 console timeout 0 dhcpd dns 10.0.0.101 dhcpd lease 7200 dhcpd domain blah.com ! dhcpd address 10.0.0.110-10.0.0.170 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 63.111.165.21 webvpn enable outside svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable group-policy EASYVPN internal group-policy EASYVPN attributes dns-server value 10.0.0.101 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-policy tunnelspecified split-tunnel-network-list value SPLIT-TUNNEL-VPN ! tunnel-group client type remote-access tunnel-group client general-attributes address-pool (inside) IPSECVPN-POOL address-pool IPSECVPN-POOL default-group-policy EASYVPN dhcp-server 10.0.0.253 tunnel-group client ipsec-attributes pre-shared-key * tunnel-group CLIENTVPN type ipsec-l2l tunnel-group CLIENTVPN ipsec-attributes pre-shared-key * ! class-map inspection_default match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect icmp ! service-policy global_policy global prompt hostname context I'm not sure where I should go next with troubleshooting nslookup result: Default Server: blahname.blah.lan Address: 10.0.0.101

  Read the article

• SQL Server 2008: Using Multiple dts Ranges to Build a Set of Dates

  - by raoulcousins

  I'm trying to build a query for a medical database that counts the number of patients that were on at least one medication from a class of medications (the medications listed below in the FAST_MEDS CTE) and had either: 1) A diagnosis of myopathy (the list of diagnoses in the FAST_DX CTE) 2) A CPK lab value above 1000 (the lab value in the FAST_LABS CTE) and this diagnosis or lab happened AFTER a patient was on a statin. The query I've included below does that under the assumption that once a patient is on a statin, they're on a statin forever. The first CTE collects the ids of patients that were on a statin along with the first date of their diagnosis, the second those with a diagnosis, and the third those with a high lab value. After this I count those that match the above criteria. What I would like to do is drop the assumption that once a patient is on a statin, they're on it for life. The table edw_dm.patient_medications has a column called start_dts and end_dts. This table has one row for each prescription written, with start_dts and end_dts denoting the start and end date of the prescription. End_dts could be null, which I'll take to assume that the patient is currently on this medication (it could be a missing record, but I can't do anything about this). If a patient is on two different statins, the start and ends dates can overlap, and there may be multiple records of the same medication for a patient, as in a record showing 3-11-2000 to 4-5-2003 and another for the same patient showing 5-6-2007 to 7-8-2009. I would like to use these two columns to build a query where I'm only counting the patients that had a lab value or diagnosis done during a time when they were already on a statin, or in the first n (say 3) months after they stopped taking a statin. I'm really not sure how to go about rewriting the first CTE to get this information and how to do the comparison after the CTEs are built. I know this is a vague question, but I'm really stumped. Any ideas? As always, thank you in advance. Here's the current query: WITH FAST_MEDS AS ( select distinct statins.mrd_pt_id, min(year(statins.order_dts)) as statin_yr from edw_dm.patient_medications as statins inner join mrd.medications as mrd on statins.mrd_med_id = mrd.mrd_med_id WHERE mrd.generic_nm in ( 'Lovastatin (9664708500)', 'lovastatin-niacin', 'Lovastatin/Niacin', 'Lovastatin', 'Simvastatin (9678583966)', 'ezetimibe-simvastatin', 'niacin-simvastatin', 'ezetimibe/Simvastatin', 'Niacin/Simvastatin', 'Simvastatin', 'Aspirin Buffered-Pravastatin', 'aspirin-pravastatin', 'Aspirin/Pravastatin', 'Pravastatin', 'amlodipine-atorvastatin', 'Amlodipine/atorvastatin', 'atorvastatin', 'fluvastatin', 'rosuvastatin' ) and YEAR(statins.order_dts) IS NOT NULL and statins.mrd_pt_id IS NOT NULL group by statins.mrd_pt_id ) select * into #meds from FAST_MEDS ; --return patients who had a diagnosis in the list and the year that --diagnosis was given with FAST_DX AS ( SELECT pd.mrd_pt_id, YEAR(pd.init_noted_dts) as init_yr FROM edw_dm.patient_diagnoses as pd inner join mrd.diagnoses as mrd on pd.mrd_dx_id = mrd.mrd_dx_id and mrd.icd9_cd in ('728.89','729.1','710.4','728.3','729.0','728.81','781.0','791.3') ) select * into #dx from FAST_DX; --return patients who had a high cpk value along with the year the cpk --value was taken with FAST_LABS AS ( SELECT pl.mrd_pt_id, YEAR(pl.order_dts) as lab_yr FROM edw_dm.patient_labs as pl inner join mrd.labs as mrd on pl.mrd_lab_id = mrd.mrd_lab_id and mrd.lab_nm = 'CK (CPK)' WHERE pl.lab_val between 1000 AND 999998 ) select * into #labs from FAST_LABS; -- count the number of patients who had a lab value or a medication -- value taken sometime AFTER their initial statin diagnosis select count(distinct p.mrd_pt_id) as ct from mrd.patient_demographics as p join #meds as m on p.mrd_pt_id = m.mrd_pt_id AND ( EXISTS ( SELECT 'A' FROM #labs l WHERE p.mrd_pt_id = l.mrd_pt_id and l.lab_yr >= m.statin_yr ) OR EXISTS( SELECT 'A' FROM #dx d WHERE p.mrd_pt_id = d.mrd_pt_id AND d.init_yr >= m.statin_yr ) )

  Read the article

• Boost::Spirit::Qi autorules -- avoiding repeated copying of AST data structures

  - by phooji

  I've been using Qi and Karma to do some processing on several small languages. Most of the grammars are pretty small (20-40 rules). I've been able to use autorules almost exclusively, so my parse trees consist entirely of variants, structs, and std::vectors. This setup works great for the common case: 1) parse something (Qi), 2) make minor manipulations to the parse tree (visitor), and 3) output something (Karma). However, I'm concerned about what will happen if I want to make complex structural changes to a syntax tree, like moving big subtrees around. Consider the following toy example: A grammar for s-expr-style logical expressions that uses autorules... // Inside grammar class; rule names match struct names... pexpr %= pand | por | var | bconst; pand %= lit("(and ") >> (pexpr % lit(" ")) >> ")"; por %= lit("(or ") >> (pexpr % lit(" ")) >> ")"; pnot %= lit("(not ") >> pexpr >> ")"; ... which leads to parse tree representation that looks like this... struct var { std::string name; }; struct bconst { bool val; }; struct pand; struct por; struct pnot; typedef boost::variant<bconst, var, boost::recursive_wrapper<pand>, boost::recursive_wrapper<por>, boost::recursive_wrapper<pnot> > pexpr; struct pand { std::vector<pexpr> operands; }; struct por { std::vector<pexpr> operands; }; struct pnot { pexpr victim; }; // Many Fusion Macros here Suppose I have a parse tree that looks something like this: pand / ... \ por por / \ / \ var var var var (The ellipsis means 'many more children of similar shape for pand.') Now, suppose that I want negate each of the por nodes, so that the end result is: pand / ... \ pnot pnot | | por por / \ / \ var var var var The direct approach would be, for each por subtree: - create pnot node (copies por in construction); - re-assign the appropriate vector slot in the pand node (copies pnot node and its por subtree). Alternatively, I could construct a separate vector, and then replace (swap) the pand vector wholesale, eliminating a second round of copying. All of this seems cumbersome compared to a pointer-based tree representation, which would allow for the pnot nodes to be inserted without any copying of existing nodes. My question: Is there a way to avoid copy-heavy tree manipulations with autorule-compliant data structures? Should I bite the bullet and just use non-autorules to build a pointer-based AST (e.g., http://boost-spirit.com/home/2010/03/11/s-expressions-and-variants/)?

  Read the article

• Organising XML results as cells in container (AS3)

  - by PJ Palomaki

  Hi, I'm having some problems figuring out how to organise data pulled off XML in cells within a container. I'm sure this should be a basic thing in AS3, but my head's fried.. can anyone help? Basically an array if fed to callThumbs() which iterates through it and compares the entries with preloaded XML _my_images. If match is found, it's sent to processXML which loads all relevant info and loads a .jpg thumbnail. All this is then fed to createCell which creates a specific cell with position values depending on x_counter and y_counter values (4 cells in a row) and adds the cell into a container _container_mc. The Problem: This all works fine and looks fine, the problem is that the cells within the container do not display in descending order. They are in random order, probably because some of the .jpg's takes longer to load etc. How do I easily organise the cells within the container in descending order by the XML .id value? Or how do I tell Flash to wait till the thumbnail and data is loaded and the cell created and added? Thanks guys, would really appreciate all the help! PJ //Flash (AS3) function callThumbs(_my_results:Array):void { // selector = 1 for specific items, 2 for search items var _thumb_url:XML; for (var r:Number=0; r < _my_results.length; r++) { // iterate through results vector, compare with _my_images XML .id for (var i:Number=0; i < _my_images.length(); i++) { if (_my_images[i][email protected]() == _my_results[r]) { _thumb_url=_my_images[i]; processXML(_thumb_url, i); } } } } // End callThumbs function processXML(imageXML:XML, num:Number) { // Processes XML data and loads .jpg thumbnail var _thumb_loader=new Loader(); _thumb_loader.load(new URLRequest("thumbs/thumb_sm/" + imageXML.@id + "_st.jpg")); _thumb_loader.contentLoaderInfo.addEventListener(Event.COMPLETE,thumbLoaded); _thumb_loader.contentLoaderInfo.addEventListener(IOErrorEvent.IO_ERROR, urlNotFound); var id:XMLList = new XMLList; id = imageXML.@id; var description:XMLList = new XMLList; description = imageXML.@description; function urlNotFound(event:IOErrorEvent):void { trace("The image URL '" + String(imageXML.@id) + "' was not found."); } function thumbLoaded(e:Event):void { var imageLoader:Loader = Loader(e.target.loader); var bm:Bitmap = Bitmap(imageLoader.content); createCell(bm, id, description, num); adjustFooterBar(); // Adjust bottom footer } } // End processXML private function createCell(_image:Bitmap, _id, _description:String, _position):void { // Creates a cell with data, add to container var _cell_mc = new CellTitle(); _cell_mc.initCell(_image, _id, _description, _position, x_counter, y_counter); if (x_counter+1 < 4) { x_counter++; } else { x_counter = 0; y_counter++; } _container_mc.addChild(_cell_mc); // movieclip container } // End createCell

  Read the article

• ASP.MVC 1.0 complex ViewModel not populating on Action

  - by Graham

  Hi, I'm 3 days into learning MVC for a new project and i've managed to stumble my way over the multitude of issues I've come across - mainly about something as simple as moving data to a view and back into the controller in a type-safe (and manageable) manner. This is the latest. I've seen this reported before but nothing advised has seemed to work. I have a complex view model: public class IndexViewModel : ApplicationViewModel { public SearchFragment Search { get; private set; } public IndexViewModel() { this.Search = new SearchFragment(); } } public class SearchFragment { public string ItemId { get; set; } public string Identifier { get; set; } } This maps to (the main Index page): %@ Page Title="" Language="C#" MasterPageFile="~/Views/Shared/Site.Master" Inherits="System.Web.Mvc.ViewPage<IndexViewModel>" %> <asp:Content ID="Content1" ContentPlaceHolderID="MainContent" runat="server"> <% Html.BeginForm("Search", AvailableControllers.Search, FormMethod.Post); %> <div id="search"> <% Html.RenderPartial("SearchControl", Model.Search); %> </div> <% Html.EndForm(); %> </asp:Content> and a UserControl: <%@ Control Language="C#" Inherits="System.Web.Mvc.ViewUserControl<SearchFragment>" %> <p> <label for="itemId"> <%= Html.Resource("ItemId") %></label> <%= Html.TextBox("itemId", Model.ItemId)%> </p> <p> <label for="title"> <%= Html.Resource("Title") %></label> <%= Html.TextBox("identifier", Model.Identifier)%> </p> <p> <input type="submit" value="<%= Html.Resource("Search") %>" name="search" /> </p> This is returned to the following method: [AcceptVerbs(HttpVerbs.Post)] public ActionResult Search(IndexViewModel viewModel) { .... } My problem is that when the view model is rehydrated from the View into the ViewModel, the SearchFragment elements are null. I suspect this is because the default model binder doesn't realise the HTML ItemId and Identifier elements rendered inline in the View map to the SearchFragment class. When I have two extra properties (ItemId and Identifier) in the IndexViewModel, the values are bound correctly. Unfortunately, as far as I can tell, I must use the SearchFragment as I need this to strongly type the Search UserControl... as the control can be used anywhere it can operate under any parent view. I really don't want to make it use "magic strings". There's too much of that going on already IMO. I've tried prefixing the HTML with "Search." in the hope that the model binder would recognise "Search.ItemId" and match to the IndexViewModel "Search" property and the ItemId within it, but this doesn't work. I fear I'm going to have to write my own ModelBinder to do this, but surely this must be something you can do out-of-the-box?? Failing that is there any other suggestions (or link to someone who has already done this?) Here's hoping....

  Read the article

• Why does Saxon evaluate the result-document URI to be the same?

  - by Jan

  My XSL source document looks like this <Topology> <Environment> <Id>test</Id> <Machines> <Machine> <Id>machine1</Id> <modules> <module>m1</module> <module>m2</module> </modules> </Machine> </Machines> </Environment> <Environment> <Id>production</Id> <Machines> <Machine> <Id>machine1</Id> <modules> <module>m1</module> <module>m2</module> </modules> </Machine> <Machine> <Id>machine2</Id> <modules> <module>m3</module> <module>m4</module> </modules> </Machine> </Machines> </Environment> </Topology> I want to create one result-document per machine, so I use the following stylesheet giving modelDir as path for the result-documents as parameter. <xsl:output method="xml" version="1.0" encoding="UTF-8" indent="yes" name="myXML" doctype-system="http://java.sun.com/dtd/properties.dtd"/> <xsl:template match="/"> <xsl:for-each-group select="/Topology/Environment/Machines/Machine" group-by="Id"> <xsl:variable name="machine" select="Id"/> <xsl:variable name="filename" select="concat($modelDir,$machine,'.xml')" /> <xsl:message terminate="no">Writing machine description to <xsl:value-of select="$filename"/></xsl:message> <xsl:result-document href="$filename" format="myXML"> <xsl:variable name="currentMachine" select="Id"/> <xsl:for-each select="current-group()/LogicalHosts/LogicalHost"> <xsl:variable name="environment" select="normalize-space(../../../../Id)"/> <xsl:message terminate="no">Module <xsl:value-of select="."/> for <xsl:value-of select="$environment"/></xsl:message> </xsl:for-each> </xsl:result-document> </xsl:for-each-group> </xsl:template> As my messages show me this seems to work fine - if saxon would not evaluate the URI of the result-document to be the same and thus give the following output. Writing machine description to target/build/model/m1.xml Module m1 for test Module m2 for test Module m1 for production Module m2 for production Writing machine description to target/build/model/m2.xml Error at xsl:result-document on line 29 of file:/C:/Projekte/.../machine.xsl: XTDE1490: Cannot write more than one result document to the same URI, or write to a URI that has been read: file:/C:/Projekte/.../$filename file:/C:/Projekte/.../machine.xsl(29,-1) : here Cannot write more than one result document to the same URI, or write to a URI that has been read: file:/C:/Projekte/.../$filename ; SystemID: file:/C:/Projekte/.../machine.xsl; Line#: 29; Column#: -1 net.sf.saxon.trans.DynamicError: Cannot write more than one result document to the same URI, or write to a URI that has been read: file:/C:/Projekte/.../$filename at net.sf.saxon.instruct.ResultDocument.processLeavingTail(ResultDocument.java:300) at net.sf.saxon.instruct.Block.processLeavingTail(Block.java:365) at net.sf.saxon.instruct.Instruction.process(Instruction.java:91) Any ideas on how to solve this?

  Read the article

< Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >