Search Results

Search found 11050 results on 442 pages for 'video cards'.

Page 254/442 | < Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >

• Any way to stop VMWare workstation from dropping SSH connections?

  - by oljones

  I have VMWare workstation 8 with a few Linux guests. I have had problems maintaining an active SSH connection to my VMs when they are in bridged mode. I first read that the onboard realtek network cards were not well supported so I bought a Intel Pro/1000 GT card. This supposedly had support. But this made no difference. Connections via SSH are active for about the first 3 minutes then hang and die. I have changed the TCP Checksum offload on the Intel and Realtek NICs, but this only works some of the time and even then not for very long. The best I could do was about 20 minutes before the connection was dropped. Any ideas?

  Read the article

• Bridge virtual machines out WLAN interface

  - by Thomas

  It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

  Read the article

• Can someone recommend a Compact Flash card to be used as a boot disk

  - by Hamish Downer

  I have an early Acer Aspire One netbook, and the flash drive is really slow at writing. I've taken it apart to add more RAM, but I've pretty much stopped using it. I've read about people replacing the SSD with a Compact Flash card and a CF to ZIF adapter but I've also read about some Compact Flash cards where the manufacturer has permanently disabled the boot flag to stop people doing this kind of mod. (Can't find the link any more though). So my most specific question is: can someone recommend a compact flash card that does allow the boot flag to be set? Please say whether you've done it yourself, or just heard about it from someone else. Beyond that, is this generally a problem?

  Read the article

• Satellite TV on my PC?

  - by jasondavis

  What would be a good solution for hooking up the satellite TV box (Dish network) in my room to be able to watch it on my PC and possibly record video from it? Please share with me the best cards, cables, software, anything else needed to do this in the most efficient way? I am looking at the WinTV-HVR from Hauppauge. I am not sure, for performance, what would be the best to go with, PCI, PCI express, USB2.0? Also on the Hauppauge website I saw this note: "WinTV-PVR products will not work in PC systems with 4GB or more of memory." The new PC I am building will be 12-24gb of DDR3 RAM, does that mean their products will not work at all with my memory? So confused now!

  Read the article

• Software RAID 10 on Linux

  - by vpetersson

  For a long time, I've been thinking about switching to RAID 10 on a few servers. Now that Ubuntu 10.04 LTS is live, it's time for an upgrade. The servers I'm using are HP Proliant ML115 (very good value). It has four internal 3.5" slots. I'm currently using one drive for the system and a RAID5 array (software) for the remaining three disks. The problem is that this creates a single-point-of-failure on the boot drive. Hence I'd like to switch to a RAID10 array, as it would give me both better I/O performance and more reliability. The problem is only that good controller cards that supports RAID10 (such as 3Ware) cost almost as much as the server itself. Moreover software-RAID10 does not seem to work very well with Grub. What is your advice? Should I just keep running RAID5? Have anyone been able to successfully install a software RAID10 without boot issues?

  Read the article

• PCI max throughput

  - by allentown

  Hypothetical here, but I want to understand. Say I have a hand me down machine, 4 PCI slots, 64-bit 33 MHz PCI. How much data can that PCI bus handle? System bus is 133 MHz. I want to use one slot for a SATA II card, and the rest for Gig-E cards, building out as fast a NAS as I can. I think one slot may be AGP2x, so that leaves me 2 for Gig-E and one for SATAT II. Will I saturate, what is the max bandwidth of the PCI bus?

  Read the article

• Thin virtual host

  - by Adam Ryczkowski

  My work setup relies on old Windows XP. Now, when Windows XP isn't supported by new hardware, it's getting harder and harder to buy a notebook on which Windows XP can run natively with all essential hardware (wireless cards, graphics, sound etc). Since I don't expect my personal setup to turn away from Windows XP any time soon, I'm investigating the following trick: why not buy any decent hardware which Linux can fully utilize, and use it as a virtual host for a guest session with e.g. Windows XP. I like using hibernation, so I prefer this Linux to be as thin as possible, only enough to support VirtualBox, KVM or any other virtualization software. Question: Are there any "standard" ways to do this, like Linux distributions aimed specifically on being light virtualization host?

  Read the article

• Can't Use Switchable Graphics

  - by Rev

  I can't get my switchable graphics cards working on my Acer 4820TG laptop. It came installed with Windows 7, but I've installed the RTM build of Windows 8. I have to keep the "Graphics" setting on the BIOS set to "Discrete," if it's set to "Switchable" the screen turns black after the boot animation is complete. The machine has an Intel graphics card and an AMD Mobility Radeon HD 5650, and I know that the Intel card is working. I've seen it work a couple of times with Windows 8 installed, but for some reason it just doesn't anymore. I know that it's not broken, because when I plug in a secondary monitor, and move the cursor to the right, I can see it on that monitor. Are there drivers or something I need to install? I've tried a number of drivers and utilities from Acer's website, none of which have fixed the problem.

  Read the article

• In Ubuntu, how do I change my default Greek font?

  - by Matthew

  I'm taking a course in ancient Greek, and I store notes and flash cards on my computer. However, by default Ubuntu uses a modern Greek font. This changes some noticable things--for example, a circumflex is ? instead of a?. I can type the circumflex by switching back to english and entering the unicode combining character u0311 (which is what I just did to type the second a), but obviously this is very cumbersome. I've installed the "ttf-linex" package from the Ubuntu repositories, which claims to include an ancient Greek font. But I have no idea how to enable this font for whenever I switch to the Greek keyboard layout.

  Read the article

• Case for Micro SD card?

  - by Josh

  I have a MicroSD card which I'd like to keep with me at all times, I.E. in my wallet. I'm looking for a case for it. But all the cases I can find seem to be for standard SD cards... the closest I could find was this: Which is completly pointless, it stores the Micro SD card along with it's adaptor. Why not just put the Micro SD card IN the adaptor and store both on a normal SD card case... Anyway, does what I'm looking for (a case to protect a microSD card, and only large enough for a mircoSD card, i.e. not what's pictured above) exist?

  Read the article

• Building optimal custom machine for Sql Server

  - by Chad Grant

  Getting the hardware in the mail any day. Hardware related to my question: x10 15.5k RPM SAS Segate Cheetah's x2 Adaptec 5405 PCIe Raid cards Motherboard has integrated SAS raid. Was thinking I would build 2 RAID 10 arrays one for data and one for logs The remaining 2 drives a RAID 0 for TempDB Will probably throw in a drive for OS. Does putting the Sql Server application / exe's on a raid make a difference and is there any impact of leaving the OS on a relatively slow disk compared to the raid arrays? I have 5/6 DBs combined < 50 gigs. With a relatively good / constant load. Estimating 60-7% reads vs writes. Planning on using log shipping as well if that matters. Any advice or suggestions?

  Read the article

• Thin virtual host [migrated]

  - by Adam Ryczkowski

  My work setup relies on old Windows XP. Now, when Windows XP isn't supported by new hardware, it's getting harder and harder to buy a notebook on which Windows XP can run natively with all essential hardware (wireless cards, graphics, sound etc). Since I don't expect my personal setup to turn away from Windows XP any time soon, I'm investigating the following trick: why not buy any decent hardware which Linux can fully utilize, and use it as a virtual host for a guest session with e.g. Windows XP. I like using hibernation, so I prefer this Linux to be as thin as possible, only enough to support VirtualBox, KVM or any other virtualization software. Question: Are there any "standard" ways to do this, like Linux distributions aimed specifically on being light virtualization host?

  Read the article

• Which driver for "ATI Mobility Radeon HD 3650" in a laptop?

  - by Lasse V. Karlsen

  We have some HP laptops here that comes equipped with a video card that identifies itself as "ATI Mobility Radeon HD 3650", like this one. However, which drivers do we choose? As far as we can tell, HD 3650 is desktop cards, or at least there are no drivers listed for that series with "Mobility" in their name. If I pick the following on the ATI Driver Download page: Graphics Windows Vista 32-bit Edition Mobility Radeon Then the dropdown for the card model contains X300, X600, X700, X800, X1300, X1400, X1600, X1800, 9600, 9700 and 9800 models, but no "HD" nor "36xx series". However, if I change to just "Radeon" for the last selection there, I can find a "Radeon HD 3600 Series" model in the list. Also, if I pick "Windows 7" as the operating system, I can find a "Mobility Radeon HD 3000 series" card, but no 3600. So, which one to pick? The main reason I ask is that they all seem to have some kind of problem installing, so neither seems to be the right one (they all crash with "Catalyst Install Manager has stopped working".)

  Read the article

• Triple Monitor Stand Recommendations

  - by Josh W.

  I've got two Acer X233Hbid 23" Widescreen LCD Monitors from new egg back last summer, each weigh 10.5lbs a piece I Want to Buy a third Acer 23" (closest I've found is the X235 on Newegg, weighs in at 11.5 lbs) , one of the new ATI video cards that will output to 3 displays, and then a monitor stand that will let me use them in portrait mode like the image below. I found the following: $260 - ERGOTRON 33-323-200 DS100 Triple-Monitor Desk Stand and was wondering if anyone has any experience with this kind of setup and whether it would work for me or not.. Thanks!

  Read the article

• Upgrade AirPort on Macs to support Snow Leopard's Wake on Wireless/WLAN?

  - by wojo

  Snow Leopard now supports Wake on WLAN, but not all hardware supports this. For example, my Octo Mac Pro from early 2008 has an AirPort card, but it does not support this. Nor does my 2007 2.33GHz MacBook Pro. For reference to what is needed, look at http://www.macrumors.com/2009/08/28/a-closer-look-at-snow-leopards-wake-on-demand-feature/ which includes a screenshot of what the System Profiler should show. It's pretty hard to find Apple parts, but is it possible to put newer cards into these machines to have them support Wake on Wireless?

  Read the article

• Need assistance setting up Linux Router with 2 public lans

  - by user195407

  I was assigned a.b.c.10/30 (Public IP) for my router and given a.b.c.9 as the gateway. I was also assigned x.y.z.128/25 (Public IP block) for my use. I want to setup a Linux router to handle this situation. My Linux box has 3 NICs, eth0 is a.b.c.10, eth1 I have assigned x.y.z.254, eth2 is unused at present. I have eth1 connected to a network switch, and several devices connected. Let's say box A is x.y.z.129 with a gateway of x.y.z.254. I have not connected to the network yet, as it is not live. What settings do I need to make, beyond adding the 2 network definitions to the cards and having "route add default gw a.b.c.9 eth0"? I may add a private 192.168.100.0/24 lan to eth2 later.

  Read the article

• Considering building a new system; but undecided about chassis

  - by J.C. Bengtson

  I'm considering a new system build, and was thinking that this particular motherboard has features I need and like: http://www.tigerdirect.com/applications/searchtools/item-details.asp?EdpNo=667651&pagenumber=1&RSort=1&csid=ITD&recordsPerPage=5&body=REVIEWS#CustomerReviewsBlock .. but am unsure which model chassis to pair it with. I'd strongly prefer something from Cooler Master, as I'm a fan of their products, but am having a hard time deciding, and also don't want to get into some odd situation where the board doesn't properly fit. I plan on having two optical drives (5.25"), two internal HDs (3.5"), and will likely go with an SLI setup of 2 or possibly even 3 cards, so I'd need a chassis that is roomy enough to accomodate all of that, as well as the motherboard itself. Based on the stock available at that same site, do you all have any suggestions? The larger, the better, as I hate having components crammed together. Your help is most appreciated!

  Read the article

• AMD chipset VS SLi

  - by djechelon

  Hello, I currently own a Crosshair 2 Formula which is broken and I need to replace. Recently, I bought a Phenom 2 CPU which I wouldn't like to throw away. Recent Crosshairs are based (as opposed to the Rampage series) on chipsets that are certified for AMD Crossfire. The problem is that I have 3 SLi cards I absolutely don't want to change with AMD card(s) since I use 3D Vision, and I need NVidia. If I buy a Crosshair 3 or 4 which is not SLi certified, will SLi still work? Else, could you suggest me a good gaming motherboard with AM3 socket and that works with 3-way SLi? Thank you in advance. [Edit] I'm asking this question because it seems Crosshair 2 is difficult to find among the market

  Read the article

• Does upgrading RAM causes increase in Graphic card's share?

  - by A.S.

  I have asked this question on Ask Ubuntu, and I was suggested to Upgrade RAM from most voted answers. But I got a point about my graphics card. Since, I can upgrade RAM and not graphics card, Does upgrading RAM also cause graphics memory to increase. To clear the point: My specs are given below: Laptop : Lenovo 3000 Y410. (bought in 2008 October) RAM: 1 GB (DDR2) External Graphics (Dedicated): N/A Internal Graphics (Shared): 256 MB Graphics Chipset: Intel GMA X3100 My Question is: If I increase my RAM to 3 GB, will it increase graphics cards share of the Memory. In other word, If graphics card shares 256 MB in 1GB RAM, will it share more, when I upgrade the RAM into 2GB or more ? Authentic resource link will be much appreciated I have recently known that, My chipset GMA X3100 can address 384 MB of RAM. So the question.

  Read the article

• 3 or 4 monitors with Nvidia and Ubuntu

  - by Jason

  I saw that you are (were?) running 4 monitors with Ubuntu 8.10 and two Nvidia cards (http://stackoverflow.com/questions/27113/how-to-use-3-monitors). I was curious if you were doing this with Xinerama, a hacked up TwinView config, or multiple X screens, or some other method? Does it work with compiz? I intend to run my Dell 30" in the middle with two 1280x1024 on the sides and continue to use one X screen, and run compiz, on Ubuntu 9.04. Currently, I am using 2 monitors with twinview and compiz, which runs fantastic. I just can't get the third monitor running (unless I enable it in its own X screen, and then enable Xinerama to enable windows to be dragged as if all one X screen, but this breaks compiz, and I don't care much for having separate X screen). I am very interested in knowing how you set up 4 monitors with 2 GPU's. Thanks!

  Read the article

• iptables forward rule not working in openwrt

  - by Udit Gupta

  I am trying to apply some iptables forwarding rules in openwrt. Here is my scenario - My server has two cards ath0 and br-lan. br-lan is connected to internet and ath0 to private network. The other m/c in n/w also has ath0 that connects with this server's ath0 and they are able to ping each other. Now, I want other m/c in network to use internet using br-lan of server so I thought of using iptables forwarding rule- Here is what I tried - Server : $ ping 1.1.1.6 // <ath0-ip of client> works fine $ iptables -A FORWARD -i ath0 -o br-lan -j ACCEPT $ /etc/init.d/firewall restart Client : $ ping 1.1.1.5 // <ath0-ip of server> works fine $ ping 132.245.244.60 // <br-lan ip of server> (not working) I am new to iptables stuff and openwrt. What I am doing wrong here ?? Any other help if anyone could suggest for my scenario Edit- m/c - machine n/w - network

  Read the article

• Causes of hard crashes on Windows XP and how to debug

  - by Sam Brightman

  I am occasionally seeing hard lockups on XP: totally unresponsive to keyboard/mouse, screen freezes at time of crash, no SSH/VNC possible. Very intermittent, nothing in the logs. I never see a blue screen on any kind of error message. This morning I logged in via VNC, logged out again, 20 minutes later physically sat at PC and it crashed around the time of VNC logout. I tend to suspect video cards in these kind of situations but it's a modern-ish card with modern drivers (one revision back, but this has been happening for 5 revisions or more) and normally would at least see a blue screen I expect. What would you suspect? Where can I look or what can I set up for more information? Bear in mind that this happens about once every 3 or 4 weeks, so extensive logging or intrusive monitoring isn't really an option.

  Read the article

• PCMCIA preventing laptop from booting up

  - by Pongus

  My friend has brought his dead laptop over. It is a Sony Vaio with Windows Vista. When booting up, it blue screens and reboots. I have tried to boot up with Knoppix and this will freeze when starting up PCMCIA. If I start Knoppix with knoppix nopcmcia it disables pcmcia and boots up fine. So I presume there is a problem with the PCMCIA controller on the laptop. My friend does not use any PCMCIA cards, so doesnt really need it. Is there anyway I can similarly disable PCMCIA so that Windows will boot up fine?

  Read the article

• Hyper-V virtual machine unable to get IP address from DHCP server running on same physical box

  - by Bronumski

  We have a Windows server 2008 R2 with two network cards running AD, DHCP, DNS and Hyper-V The first nic is setup with a static IP address and DHCP, WDS, and DNS are bound to it. The second nic is configured in Hyper-V to be only used by Hyper-V and has been automatically configured so that only the virtual switch is enabled on the adapter. DHCP and DNS work fine for all physical machines on the network. It also works for Virtual Machines running on another physical box. Virtual machines that are bound to the virtual switch network adapter are unable to get a IP address. If the virtual machine is given a static IP address with correct subnet, gateway and dns everything works. Has anyone else got this working?

  Read the article

• fsck: FILE SYSTEM WAS MODIFIED after each check with -c, why?

  - by Chris

  Hi I use a script to partition and format CF cards (connected with a USB card writer) in an automated way. After the main process I check the card again with fsck. To check bad blocks I also tried the '-c' switch, but I always get a return value != 0 and the message "FILE SYSTEM WAS MODIFIED" (see below). I get the same result when checking the very same drive several times... Does anyone know why a) the file system is modified at all and b) why this seems to happen every time I check and not only in case of an error (like bad blocks)? Here's the output: linux-box# fsck.ext3 -c /dev/sdx1 e2fsck 1.40.2 (12-Jul-2007) Checking for bad blocks (read-only test): done Pass 1: Checking inodes, blocks, and sizes Pass 2: Checking directory structure Pass 3: Checking directory connectivity Pass 4: Checking reference counts Pass 5: Checking group summary information Volume (/dev/sdx1): ***** FILE SYSTEM WAS MODIFIED ***** Volume (/dev/sdx1): 5132/245760 files (1.2% non-contiguous), 178910/1959896 blocks Thanks, Chris

  Read the article

< Previous Page | 250 251 252 253 254 255 256 257 258 259 260 261  | Next Page >