Search Results

Search found 10402 results on 417 pages for 'pc maintenance'.

Page 255/417 | < Previous Page | 251 252 253 254 255 256 257 258 259 260 261 262  | Next Page >

• UFW as an active service on Ubuntu

  - by lamcro

  Every time I restart my computer, and check the status of the UFW firewall (sudo ufw status), it is disabled, even if I then enable and restart it. I tried putting sudo ufw enable as one of the startup applications but it asks for the sudo password every time I log on, and I'm guessing it does not protect anyone else who logs on my computer. How can I setup ufw so it is activated when I turn on my computer, and protects all accounts? Update I just tried /etc/init.d/ufw start, and it activated the firewall. Then I restarted the computer, and again it was disabled. content of /etc/ufw/ufw.conf # /etc/ufw/ufw.conf # # set to yes to start on boot ENABLED=yes # set to one of 'off', 'low', 'medium', 'high' LOGLEVEL=full content of /etc/default/ufw # /etc/default/ufw # # Set to yes to apply rules to support IPv6 (no means only IPv6 on loopback # accepted). You will need to 'disable' and then 'enable' the firewall for # the changes to take affect. IPV6=no # Set the default input policy to ACCEPT, ACCEPT_NO_TRACK, DROP, or REJECT. # ACCEPT enables connection tracking for NEW inbound packets on the INPUT # chain, whereas ACCEPT_NO_TRACK does not use connection tracking. Please note # that if you change this you will most likely want to adjust your rules. DEFAULT_INPUT_POLICY="DROP" # Set the default output policy to ACCEPT, ACCEPT_NO_TRACK, DROP, or REJECT. # ACCEPT enables connection tracking for NEW outbound packets on the OUTPUT # chain, whereas ACCEPT_NO_TRACK does not use connection tracking. Please note # that if you change this you will most likely want to adjust your rules. DEFAULT_OUTPUT_POLICY="ACCEPT" # Set the default forward policy to ACCEPT, DROP or REJECT. Please note that # if you change this you will most likely want to adjust your rules DEFAULT_FORWARD_POLICY="DROP" # Set the default application policy to ACCEPT, DROP, REJECT or SKIP. Please # note that setting this to ACCEPT may be a security risk. See 'man ufw' for # details DEFAULT_APPLICATION_POLICY="SKIP" # By default, ufw only touches its own chains. Set this to 'yes' to have ufw # manage the built-in chains too. Warning: setting this to 'yes' will break # non-ufw managed firewall rules MANAGE_BUILTINS=no # # IPT backend # # only enable if using iptables backend IPT_SYSCTL=/etc/ufw/sysctl.conf # extra connection tracking modules to load IPT_MODULES="nf_conntrack_ftp nf_nat_ftp nf_conntrack_irc nf_nat_irc" Update Followed your advise and ran update-rc.d with no luck. lester@mcgrath-pc:~$ sudo update-rc.d ufw defaults update-rc.d: warning: /etc/init.d/ufw missing LSB information update-rc.d: see <http://wiki.debian.org/LSBInitScripts> Adding system startup for /etc/init.d/ufw ... /etc/rc0.d/K20ufw -> ../init.d/ufw /etc/rc1.d/K20ufw -> ../init.d/ufw /etc/rc6.d/K20ufw -> ../init.d/ufw /etc/rc2.d/S20ufw -> ../init.d/ufw /etc/rc3.d/S20ufw -> ../init.d/ufw /etc/rc4.d/S20ufw -> ../init.d/ufw /etc/rc5.d/S20ufw -> ../init.d/ufw lester@mcgrath-pc:~$ ls -l /etc/rc?.d/*ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc0.d/K20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc1.d/K20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc2.d/S20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc3.d/S20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc4.d/S20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc5.d/S20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc6.d/K20ufw -> ../init.d/ufw

  Read the article

• Incorrect gzipping of http requests, can't find who's doing it

  - by Ned Batchelder

  We're seeing some very strange mangling of HTTP responses, and we can't figure out what is doing it. We have an app server handling JSON requests. Occasionally, the response is returned gzipped, but with incorrect headers that prevent the browser from interpreting it correctly. The problem is intermittent, and changes behavior over time. Yesterday morning it seemed to fail 50% of the time, and in fact, seemed tied to one of our two load-balanced servers. Later in the afternoon, it was failing only 20 times out of 1000, and didn't correlate with an app server. The two app servers are running Apache 2.2 with mod_wsgi and a Django app stack. They have identical Apache configs and source trees, and even identical packages installed on Red Hat. There's a hardware load balancer in front, I don't know the make or model. Akamai is also part of the food chain, though we removed Akamai and still had the problem. Here's a good request and response: * Connected to example.com (97.7.79.129) port 80 (#0) > POST /claim/ HTTP/1.1 > User-Agent: curl/7.19.7 (x86_64-pc-linux-gnu) libcurl/7.19.7 OpenSSL/0.9.8k zlib/1.2.3.3 libidn/1.15 > Host: example.com > Accept: */* > Referer: http://example.com/apps/ > Accept-Encoding: gzip,deflate > Content-Length: 29 > Content-Type: application/x-www-form-urlencoded > } [data not shown] < HTTP/1.1 200 OK < Server: Apache/2 < Content-Language: en-us < Content-Encoding: identity < Content-Length: 47 < Content-Type: application/x-javascript < Connection: keep-alive < Vary: Accept-Encoding < { [data not shown] * Connection #0 to host example.com left intact * Closing connection #0 {"msg": "", "status": "OK", "printer_name": ""} And here's a bad one: * Connected to example.com (97.7.79.129) port 80 (#0) > POST /claim/ HTTP/1.1 > User-Agent: curl/7.19.7 (x86_64-pc-linux-gnu) libcurl/7.19.7 OpenSSL/0.9.8k zlib/1.2.3.3 libidn/1.15 > Host: example.com > Accept: */* > Referer: http://example.com/apps/ > Accept-Encoding: gzip,deflate > Content-Length: 29 > Content-Type: application/x-www-form-urlencoded > } [data not shown] < HTTP/1.1 200 OK < Server: Apache/2 < Content-Language: en-us < Content-Encoding: identity < Content-Type: application/x-javascript < Content-Encoding: gzip < Content-Length: 59 < Connection: keep-alive < Vary: Accept-Encoding < X-N: S < { [data not shown] * Connection #0 to host example.com left intact * Closing connection #0 ?V?-NW?RPR?QP*.I,)-???A??????????T??Z? ??/ There are two things to notice about the bad response: It has two Content-Encoding headers, and the browsers seem to use the first. So they see an identity encoding header, and gzipped content, so they can't interpret the response. The bad response has an extra "X-N: S" header. Perhaps if I could find out what intermediary adds "X-N: S" headers to responses, I could track down the culprit...

  Read the article

• TV not detected by Windows/VGA - when there is a WHDI device in the signal chain

  - by ashwalk

  I'm at my wit's end with this one... I had an EVGA GTS 250, and I used to plug it's HDMI out into a WHDI sender, which transmitted to its corresponding WHDI receiver 15ft away, which then connected to a Samsung LN40D LCD TV through another HDMI cable. PC/VGA < [hdmi cable] < WHDI sender <[air] WHDI receiver < [hdmi cable] < TV It was perfect, stable, no perceivable latency. I just plugged everything the first time and it worked instantly. It sent 5.1 audio, and Windows/nVidia Control Center detected the TV by its name. The WHDI device is this one: http://goo.gl/Q8iWI5 Now I bought an EVGA GTX 650, and WHDI doesn't work anymore. Both Windows and nVidia Control Center won't detect the TV, only the monitor that's connected via DVI. The TV screen shows "TX202913 connected. Check video signal." on top of a black screen. Though the device is not the problem itself, just the fact that it's not allowing direct connection between PC and TV. I would bet that if put an AVR in its place I'd also have this issue. The HDMI on this new card works with other monitors. If I put the older card back, WHDI works normally. I have googled this for 5 months on and off. Once I bumped into a page that showed how to force a display device to always-on through registry edit. Once I restarted windows, the Tv (through WHDI) displayed my expanded or duplicated desktop at 1024x768 ONLY, and listed the display as "digital display". I could not change the resolution and it wouldn't playback audio (although the option was available at nVidia Control Center HDMI audio options, but did not work). This proves that there is no conflict between the devices, except that software-wise, Windows cannot, for the life of it, understand that there's a TV there to send video/audio to. Since this won't do (no audio, poor video), I reverted this regedit. It's also not an EDID problem within the TV, since when connected directly it works. The last weird bit of this saga is that today, I reminded of Windows' "Add Device" dialog, gave it a go, and a "Samsung Generic UPNP TV" showed up, which I promptly installed the drives for, rising to a climax of... ...NOTHING HAPPENING. As far as I can tell, it really didn't change anything other than using up a few kb in my main disc. I should also say that I looked a LOT into handshake problems and nothing applied either. Do any of you have an idea of what may be going on? I can't stand the thought of having a us$200 device not working because of the addition of a newer graphics card, when the much older one had no issues. There is absolutely NO REASON for this to happen. There is NO documentation on WHDI online. Apparently no one buys this stuff. For the same reason, no one responded to this same plea for help on NVidia and EVGA forums. Worst case, this can be a warning about this setup for people in the future. Thanx in advance.

  Read the article

• Why do we need different CPU architecture for server & mini/mainframe & mixed-core?

  - by claws

  Hello, I was just wondering what other CPU architectures are available other than INTEL & AMD. So, found List of CPU architectures on Wikipedia. It categorizes notable CPU architectures into following categories. Embedded CPU architectures Microcomputer CPU architectures Workstation/Server CPU architectures Mini/Mainframe CPU architectures Mixed core CPU architectures I was analyzing the purposes and have few doubts. I taking Microcomputer CPU (PC) architecture as reference and comparing others. Embedded CPU architecture: They are a completely new world. Embedded systems are small & do very specific task mostly real time & low power consuming so we do not need so many & such wide registers available in a microcomputer CPU (typical PC). In other words we do need a new small & tiny architecture. Hence new architecture & new instruction RISC. The above point also clarifies why do we need a separate operating system (RTOS). Workstation/Server CPU architectures I don't know what is a workstation. Someone clarify regarding the workstation. As of the server. It is dedicated to run a specific software (server software like httpd, mysql etc.). Even if other processes run we need to give server process priority therefore there is a need for new scheduling scheme and thus we need operating system different than general purpose one. If you have any more points for the need of server OS please mention. But I don't get why do we need a new CPU Architecture. Why cant Microcomputer CPU architecture do the job. Can someone please clarify? Mini/Mainframe CPU architectures Again I don't know what are these & what miniframes or mainframes used for? I just know they are very big and occupy complete floor. But I never read about some real world problems they are trying to solve. If any one working on one of these. Share your knowledge. Can some one clarify its purpose & why is it that microcomputer CPU archicture not suitable for it? Is there a new kind of operating system for this too? Why? Mixed core CPU architectures Never heard of these. If possible please keep your answer in this format: XYZ CPU architectures Purpose of XYZ Need for a new architecture. why can't current microcomputer CPU architecture work? They go upto 3GHZ & have upto 8 cores. Need for a new Operating System Why do we need a new kind of operating system for this kind of archictures?

  Read the article

• Server currently under DDOS, not sure what to do

  - by Volex

  My web server is currently under a DDOS attack I believe, the messages log is full of these kind of messages: May 13 15:51:19 kernel: nf_conntrack: table full, dropping packet. May 13 15:51:19 last message repeated 9 times May 13 15:51:24 kernel: __ratelimit: 78 callbacks suppressed May 13 15:51:24 kernel: nf_conntrack: table full, dropping packet. May 13 15:52:06 kernel: possible SYN flooding on port 80. Sending cookies. and a netstat has a huge amount of the following: tcp 0 0 my.host.com:http bb176da0.virtua.com.br:4998 SYN_RECV tcp 0 0 my.host.com:http 187.0.43.109:2694 SYN_RECV tcp 0 0 my.host.com:http 109.229.4.145:1722 SYN_RECV tcp 0 0 my.host.com:http 189-84-163-244.sodobr:63267 SYN_RECV tcp 0 0 my.host.com:http bd66839d.virtua.com.br:3469 SYN_RECV tcp 0 0 my.host.com:http 69.101.56.190.dsl.int:52552 SYN_RECV tcp 0 0 my.host.com:http pc-62-230-47-190.cm.vt:2262 SYN_RECV tcp 0 0 my.host.com:http 189-84-163-244.sodobr:63418 SYN_RECV tcp 0 0 my.host.com:http pc-62-230-47-190.cm.vt:1741 SYN_RECV tcp 0 0 my.host.com:http zaq3d739320.zaq.ne.jp:2141 SYN_RECV tcp 0 0 my.host.com:http netacc-gpn-4-80-73.po:52676 SYN_RECV tcpdump shows: 7:11:08.564510 IP 187-4-1xx-4.xxx.ipd.brasiltelecom.net.br.54821 > my.host.com.http: S 999692166:999692166(0) win 65535 <mss 1452,nop,nop,sackOK> 17:11:08.566347 IP 114-44-171-67.dynamic.hinet.net.1129 > my.host.com.http: S 605369055:605369055(0) win 65535 <mss 1440,nop,nop,sackOK> 17:11:08.570210 IP 200-101-13-130.pvoce300.ipd.brasiltelecom.net.br.5590 > my.host.com.http: S 2813379182:2813379182(0) win 16384 <mss 1460,nop,nop,sackOK> 17:11:08.571290 IP dsl-189-143-30-99-dyn.prod-infinitum.com.mx.1615 > my.host.com.http: S 281542700:281542700(0) win 65535 <mss 1452,nop,nop,sackOK> 17:11:08.583847 IP dsl-189-143-30-99-dyn.prod-infinitum.com.mx.1617 > my.host.com.http: S 499413892:499413892(0) win 65535 <mss 1452,nop,nop,sackOK> 17:11:08.588680 IP 170.51.229.112.2569 > my.host.com.http: S 2195084898:2195084898(0) win 65535 <mss 1460,nop,nop,sackOK> 17:11:08.588773 IP gw2-1.211.ru.3180 > my.host.com.http: F 2315901786:2315901786(0) ack 2620913033 win 64240 17:11:08.590656 IP 200-101-13-130.pvoce300.ipd.brasiltelecom.net.br.5614 > my.host.com.http: S 2813715032:2813715032(0) win 16384 <mss 1460,nop,nop,sackOK> 17:11:08.591212 IP 203.82.82.54.15848 > my.host.com.http: S 4070423507:4070423507(0) win 16384 <mss 1400,nop,nop,sackOK> 17:11:08.591254 IP 203.82.82.54.2545 > my.host.com.http: S 1790910784:1790910784(0) win 16384 <mss 1400,nop,nop,sackOK> 17:11:08.591289 IP 203.82.82.54.28306 > my.host.com.http: S 578615626:578615626(0) win 16384 <mss 1400,nop,nop,sackOK> 17:11:08.591591 IP gw2-1.211.ru.3191 > my.host.com.http: F 2316435991:2316435991(0) ack 2634205972 win 64240 17:11:08.591790 IP 200-101-13-130.pvoce300.ipd.brasiltelecom.net.br.5593 > my.host.com.http: S 2813659017:2813659017(0) win 16384 <mss 1460,nop,nop,sackOK> 17:11:08.593691 IP gw2-1.211.ru.3203 > my.host.com.http: F 2316834420:2316834420(0) ack 2629074987 win 64240 I'm not sure what I can do to limit/mitigate this, currently no webpages are being served, any help gratefully appreciated.

  Read the article

• Local DNS server (bind) and the router DHCP

  - by Luca

  I just set up an internal http server for internal use (I set up Redmine), in a small network (30 or so PCs). I set up the http server on a virtual box ubuntu, that runs also the DNS server (bind). In the DNS lookup I added the Redmine server name (redmine.engserver <- 192.168.1.14) and as forwarders the outside ISP DNS IP adresses. I am using a small wi-fi router (ASUS RT-N66U) as DHCP (and as gateway). In the DHCP config page I set up as DNS the ubuntu server IP (it is fixed 192.168.1.14). Now when I connect a new PC to the network, the DHCP router issues its new IP and as DNS servers it issues: primary: 192.168.1.14 (ubuntu machine) and seconary 192.168.1.1 (the router itself). ipconfig /all Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DHCPv6 IAID . . . . . . . . . . . : 248539109 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-15-AA-3F-D0-67-E5-49-A7-EF DNS Servers . . . . . . . . . . . : 192.168.1.14 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Before changing the DHCP setting on the router, I would always get only one DNS server: 192.168.1.1 (which uses probably DNS forwarding to external public DNS services). The problem is this: If in my browser I type www.google.com, it works all the time. If in the browser I type http://redmine.engserver/ it works most of the time, but sometimes it ends up with a yahoo page search or something else. In the DNS cache it shows as (Server not found). ipconfig /displaydns I looked with wireshark and it seems like sometimes the client PC interrogates the secondary DNS (192.168.1.1) instead of the first 192.168.1.14. Obviously this one is a public domain and it does not have the redmine.engserver entry. What is wrong in this configuration? Is it even legitimate to have 2 DNS (one internal and one forwarded by the router) which are inconsistent? Is there another way to have a local name service in a small office network? Why is the router DHCP issuing itself as DNS?

  Read the article

• Simple Cisco ASA 5505 config issue

  - by Ben Sebborn

  I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

  Read the article

• Bridging a non-persistent PPP connection to wireless (or wired) in Windows XP

  - by phooze

  I have a 3G modem-like device (eMobile's D01NX, PC card style, for any Japan nerds out there) that I use to connect my PC to the Internet. I'd like to bridge this connection with another computer either via an ad-hoc wireless network, or a simple cross-over cable (either are options). However, when I open "Network Connections", I do not see the PPP connection (otherwise I could click both and bridge). I believe this is because there is software (provided by the vendor) that is handling the card directly and registering a PPP connection dynamically. When connected, an ipconfig at the command line yields: Ethernet adapter wireless: Connection-specific DNS Suffix . : Autoconfiguration IP Address. . . : 169.254.5.169 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Ethernet adapter lan: Media State . . . . . . . . . . . : Media disconnected PPP adapter {B59EEDDE-A22B-48DF-93E5-04842B641257}: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 114.xx.xxx.xx Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 114.xx.xxx.xx (I've commented out my IP address for privacy reasons, but what does appear there is a functional Internet IP address.) When I disconnect the adapter with the vendor software, the PPP connection disappears completely from the ipconfig list. Any ideas on how to do this?

  Read the article

• What NAS setup for two-way syncing over the internet?

  - by Jamse

  I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker. Update I've been digging some more and it looks like QNAP's Remote Replication function is actually just Rsync, so only really suitable for one-way syncing. I've posted on their forum to double check, but I think that's the case. In which case, I think the focus of my question is now either: do any reasonably-priced NASs support bidirectional syncing over the internet?, or has anyone had any luck installing onto NASs for this purpose? (Also, updated question to clarify that I'm after two-way syncing.)

  Read the article

• Can I make my drives visible and change their partition type without losing my data?

  - by user165408

  I have made a lot of mistakes and now I cannot see my hard disk nor I can start my operating system on my laptop. All my passwords and important files on my hdd without any backup. I followed this course of action Changed my hard disk partitions to dynamic just for getting 5th partition. (1st mistake) Decreased partitions to 4 again. Backed up operating system from 4th to 3rd partition with Norton Ghost. Booted from a live CD for Windows XP. Formatted 4th partition and moved my all important data from 1st and 2nd partitions to the 4th partition. Deleted 1st and 2nd partitions and got 1 partition from half of empty space. So I have just 3 partitions and empty space between 1st and 2nd partitions. Tried to install Windows 8 to the first partition but it did not allow because it is dynamic. Also it did not allow to install to other partitions. Tried to install Windows XP to the 1st partition but it said if I continue I cannot use other drivers. Therefore I escaped from installing it. Booted from the Windows XP live CD then increased 1st partiton to less than 400mb of empty space. Therefore I thought it will be adjacent but it was shown as 2 partitions. In my computer I see just 3 drivers. Using Norton Ghost I recovered my OS to the 1st partition. (2nd mistake it was on 4th partition originally) Booted from a Windows XP live CD I tried to install bcdedit to the Windows XP live CD but it did not work. Then I tried to install EaseUS Partition Master Home Edition. It was installed with errors then I start it and it showed me an error like there is no hard disk. I looked to my PC and my drivers were not there. Booted from the Norton Ghost CD and it did not show me my drivers either, but before I was able to see them. I checked numbers of partition shown by the Norton Ghost utility and they are still have same numbers so I have to see my drivers but I cannot see them now. My hard disk is shown as extarnal dynamic now so I cannot see any drive in my PC in the live Windows XP. There are two options; first one is import extarnal disk and second one is convert disk to basic. Will they delete my data? I fear booting from CDs like Windows XP live CD, Norton Ghost CD, and the operating system CD/DVD, because they may overwrite a few MB their data to my data. These recover tools are already exist in Windows XP live CD by The Ultimate Boot CD for Windows. Can any of them help me? CompuAppa SwissKnife V3 DBXtract Disk Investigator Fab's AutoBackup 2.0 FileRecovery Floppy Repair Free Undelete Handy Recovery Recovery Manager Restorastion Restorastion Help File by UBCD4Win UnChk Unstoppable Copier Finally How can I make it so that my drives are visible again without losing my data? How can I convert my dynamic partitions to basic without losing my data?

  Read the article

• How do I reset/update my BIOS for Optiplex GX280?

  - by Sam Langlhey

  So far this has been a nightmare for me, which has been frustrating me constantly. I am using Dell Optiplex GX280 with Windows XP home edition, which is running a BIOS version A04. Recently, i've rebooted the pc to find out that its not booting. It will get to the Windows boot up screen with the progress bar but only to restart to the same process again, over and over. Frustrated that I am, i've inserted the Windows recovery CD to at least either repair of reinstall the operating system to find out that was not possible. I hit F8 to have the boot options, each of the boot option that I've selected gave me an error saying: "Selected boot device is not available." Right after that, I went to the BIOS setting and did a diagnostic test, which recognized all the Boot devices onboard. Now, I cannot even repair of reinstall Windows XP, because the system is not booting from none of the boot devices. The surprise is when I removed the hard-drive from the computer and loaded it on into another computer successfully; that's right, there is nothing wrong with the hard drive. After that I was totally puzzled. I found a few pointers online saying that the BIOS start-up block might be corrupted itself and I might need to flash/update the BIOS. I found the detailed instruction on how to create a Boot up disk by downloading the BIOS firmware from the manufacture's website. I did exactly as instructed below: Download the latest version or your choose version of BIOS file for your computer or motherboard from the manufacturer’s support site. Rename the downloaded file to AMIBOOT.ROM. Copy the file to a floppy disk. Insert the floppy disk to the floppy drive. Turn on the system. After I did that and powered on the PC to boot from the floppy drive, it gave me this error message: "Non-System Disk or Disk Error. Replace and Strike any key when ready." I did all that, and I kept on pressing [Ctrl]+[Home] to force it, but it did not did any satisfying result. Desperate as I am, my next attempt is to try the instruction below. Since I want to be ready, in the event it does not work, do you have any solution that you can provide? Please keep in mind that I cannot boot from any of the devices at this moment. My only hope now is to come on with a solution that will work through the Floppy drive, since that's the only drive that affected. Thank you very much for your advice and support in advance. To create a Windows startup disk, insert a floppy disk into the drive of a similarly configured, working Windows XP system, launch My Computer, right-click the floppy disk icon, and select the Format command from the context menu. When you see the Format dialog box, leave all the default settings as they are and click the Start button. Once the format operation is complete, close the Format dialog box to return to My Computer, double-click the drive C icon to access the root directory, and copy the following three files to the floppy disk: Boot.ini NTLDR Ntdetect.com

  Read the article

• What NAS setup for syncing over the internet?

  - by Jamse

  I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker.

  Read the article

• stunnel crashing

  - by Jay

  I'm trying to use stunnel to secure a legacy application's communications. I can't seem to get it setup and working. Can anyone provide any hints where I'm going wrong? Here's what I'm trying to accomplish: A windows service on a client machine connects to a server on port 7000 using TCP. I'd like to encrypt the communication between client and server. Here's what I've tried: Created a new server that accepts ssl connections on port 7443. Got a certificate for the server and installed it. That seems to work with my test setup. Installed stunnel on my windows machine (version 7.43 from the distribution archive file). Installed libssl32.dll and libeay32.dll in the same directory as stunnel.exe ( from the openssl-0.9.8h-1 binary distribution). Installed it as a service using "stunnel -install" Configured stunnel as follows: debug=7 output=C:\p4\internal\Utility\Proxy\proxy.log service=Proxy taskbar=no [exchange] accept=7000 client=yes connect=proxy.blah.com:7443 I changed my hosts file to trick the old application into connecting through stunnel: server.blah.com 127.0.0.1 # when client looks up server it goes to stunnel proxy.blah.com IP-address-of-server.blah.com # stunnel connects to new server "server.blah.com" now resolves to the machine it's running on (i.e. stunnel). "proxy.blah.com" goes to the real server. stunnel should connect to the server. I start the stunnel service and try to connect. It looks like it's working but the stunnel service just shuts down with no message. 2010.04.19 13:16:21 LOG5[4924:3716]: stunnel 4.33 on x86-pc-mingw32-gnu with OpenSSL 0.9.8h 28 May 2008 2010.04.19 13:16:21 LOG5[4924:3716]: Threading:WIN32 SSL:ENGINE Sockets:SELECT,IPv6 2010.04.19 13:16:49 LOG5[4924:3748]: Service exchange accepted connection from 127.0.0.1:4134 2010.04.19 13:16:49 LOG6[4924:3748]: connect_blocking: connecting x.80.60.32:7443 2010.04.19 13:16:49 LOG5[4924:3748]: connect_blocking: connected x.80.60.32:7443 2010.04.19 13:16:49 LOG5[4924:3748]: Service exchange connected remote server from x.253.120.19:4135 2010.04.19 13:20:24 LOG5[3668:3856]: Reading configuration from file stunnel.conf 2010.04.19 13:20:24 LOG7[3668:3856]: Snagged 64 random bytes from C:/.rnd 2010.04.19 13:20:24 LOG7[3668:3856]: Wrote 1024 new random bytes to C:/.rnd 2010.04.19 13:20:24 LOG7[3668:3856]: RAND_status claims sufficient entropy for the PRNG 2010.04.19 13:20:24 LOG7[3668:3856]: PRNG seeded successfully 2010.04.19 13:20:24 LOG7[3668:3856]: SSL context initialized for service exchange 2010.04.19 13:20:24 LOG5[3668:3856]: Configuration successful 2010.04.19 13:20:24 LOG5[3668:3856]: No limit detected for the number of clients 2010.04.19 13:20:24 LOG7[3668:3856]: FD=312 in non-blocking mode 2010.04.19 13:20:24 LOG7[3668:3856]: Option SO_REUSEADDR set on accept socket 2010.04.19 13:20:24 LOG7[3668:3856]: Service exchange bound to 0.0.0.0:7000 2010.04.19 13:20:24 LOG7[3668:3856]: Service exchange opened FD=312 2010.04.19 13:20:24 LOG5[3668:3856]: stunnel 4.33 on x86-pc-mingw32-gnu with OpenSSL 0.9.8h 28 May 2008 2010.04.19 13:20:24 LOG5[3668:3856]: Threading:WIN32 SSL:ENGINE Sockets:SELECT,IPv6 2010.04.19 13:21:02 LOG7[3668:4556]: Service exchange accepted FD=372 from 127.0.0.1:4156 2010.04.19 13:21:02 LOG7[3668:4556]: Creating a new thread 2010.04.19 13:21:02 LOG7[3668:4556]: New thread created 2010.04.19 13:21:02 LOG7[3668:3756]: Service exchange started 2010.04.19 13:21:02 LOG7[3668:3756]: FD=372 in non-blocking mode 2010.04.19 13:21:02 LOG5[3668:3756]: Service exchange accepted connection from 127.0.0.1:4156 2010.04.19 13:21:02 LOG7[3668:3756]: FD=396 in non-blocking mode 2010.04.19 13:21:02 LOG6[3668:3756]: connect_blocking: connecting x.80.60.32:7443 2010.04.19 13:21:02 LOG7[3668:3756]: connect_blocking: s_poll_wait x.80.60.32:7443: waiting 10 seconds 2010.04.19 13:21:02 LOG5[3668:3756]: connect_blocking: connected x.80.60.32:7443 2010.04.19 13:21:02 LOG5[3668:3756]: Service exchange connected remote server from x.253.120.19:4157 2010.04.19 13:21:02 LOG7[3668:3756]: Remote FD=396 initialized 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): before/connect initialization 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write client hello A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server hello A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server certificate A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read server done A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write client key exchange A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write change cipher spec A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 write finished A 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 flush data 2010.04.19 13:21:02 LOG7[3668:3756]: SSL state (connect): SSLv3 read finished A The client thinks the connection is closed: No connection could be made because the target machine actively refused it 127.0.0.1:7000 at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress) at System.Net.Sockets.Socket.Connect(EndPoint remoteEP) at Service.ConnUtility.Connect() Any suggestions?

  Read the article

• Computer not POSTing "randomly"?

  - by smoth190

  I have a custom built PC that is exhibiting some...odd... behavior, something I've never seen before. It was working fine one day, and the next day, it wouldn't start. Seeing as I wanted an upgrade anyway, I purchased a new motherboard that was compatible with all my parts. While replacing the motherboard, I accidentally damaged the CPU. Well, I wanted a new one anyway... so I got a new one. Seeing as I was replacing a ton of parts already, I bought a new PSU because the old one was super loud. When I slapped it all together, it starts up, lights, fans, drives, they all start. But I get no display from the monitor. No beeps, which I believe means it doesn't POST. I figured it was the RAM, because after removing the sound card and graphics card, there was nothing else that I hadn't replaced. When I remove both sticks of RAM, I get a continuous beeping, and according to the mobo handbook, means no RAM. So I think the mobo is functional, or atleast partly. I bought new RAM, but it still didn't work. I tried 3 monitors, with both VGA and DIV. So it's probably not the monitor, either. Now, let me get to the random part. Every 20 or so boots (I should also mention, for about 3 out of 5 boots I have to unplug the PC because it won't powerdown via the button), it will POST and I'll get display. Then, after about 2 or 3 resets, it won't work again. This confuses me so much, because even when I change nothing, it will/will not work. My thought is that maybe it has something to do with the RAM not clearing or something. I also reset the CMOS battery, incase that had anything to do with it, but no eval. I found some weird suggestion online about holding the power button for 30 seconds while it was unplugged. That did nothing, but I didn't expect it would... I've replaced just about the entire computer, and all the parts are compatible. Done about everything I can think of, but nothing has worked. Hopefully someone can help me here. And as I side note: When I do get my computer to boot, it says my hardware has changed and I have to re-activate windows. But it says I have to call Microsoft to do it. So I get this fancy automated voice that asks me to enter in a code into windows, then it asks me "How many computers have you activated with this copy of Windows?". Well, I had it on my computer before I replaced everything, so I said 1. Then he yelled at me for violating my 1-use license. I dunno what's going on there, do I have to re-purchase Windows 7? And they wonder why people pirate software... That's just a bonus question, though. Specs: 8GB of DDR2 RAM (Corsair) AMD CPU (I don't know what GHz or model because I can't find the box... (I think its 4 cores of 2.8Ghz) ASRock A785GM-LE Motherboard

  Read the article

• libvirt upgrade caused vms to not see drives (boot media not found)

  - by bias

  I upgraded to Ubuntu 12.04.1 and now libvirt (via open nebula) successfully runs vms but they aren't finding the 2 drives (specifically, the boot drive). One is "hd" the other is "cdrom". The machine boots but fails and displays something like "boot media not found hd" (this was in a vnc terminal and I didn't copy the output anywhere so that's not the verbatim message). I tried constructing a new disk using the new version of qemu (via vmbuilder) and this new machine has the same problem as the old machine. In case it matters (I can't see why it would) I'm using open nebula to manage the machines. There's nothing relevant in any of the logs: syslog, libvirtd, oned. Which is to say nothing interesting/anomalous is reported when the machine is brought up. Versions libvirt 0.9.8-2ubuntu17.4 qemu-kvm 1.0+noroms-0ubuntu14.3 The libvirt xml config portions (relavent) <os> <type arch='x86_64' machine='pc-1.0'>hvm</type> <boot dev='hd'/> </os> ... <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='qcow2'/> <source file='/var/lib/one//203/images/disk.0'/> <target dev='sda' bus='scsi'/> <alias name='scsi0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/var/lib/one//203/images/disk.1'/> <target dev='sdc' bus='scsi'/> <readonly/> <alias name='scsi0-0-2'/> <address type='drive' controller='0' bus='0' unit='2'/> </disk> <controller type='scsi' index='0'> <alias name='scsi0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </controller> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </memballoon> ... </devices> The libvirt/qemu log contains 2012-11-25 22:19:24.328+0000: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-1.0 -enable-kvm -m 256 -smp 1,sockets=1,cores=1,threads=1 -name one-204 -uuid 4be6c276-19e8-bdc2-e9c9-9ca5352f2be3 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/one-204.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -device lsi,id=scsi0,bus=pci.0,addr=0x5 -drive file=/var/lib/one//204/images/disk.0,if=none,id=drive-scsi0-0-0,format=qcow2 -device scsi-disk,bus=scsi0.0,scsi-id=0,drive=drive-scsi0-0-0,id=scsi0-0-0,bootindex=1 -drive file=/var/lib/one//204/images/disk.1,if=none,media=cdrom,id=drive-scsi0-0-2,readonly=on,format=raw -device scsi-disk,bus=scsi0.0,scsi-id=2,drive=drive-scsi0-0-2,id=scsi0-0-2 -netdev tap,fd=18,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3 -netdev tap,fd=19,id=hostnet1 -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4 -usb -vnc 0.0.0.0:204 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x6 kvm: -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom" kvm: -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom"

  Read the article

• How to make XAMPP virtual hosts accessible to VM's and other computers on LAN?

  - by martin's

  XAMPP running on Vista 64 Ultimate dev machine (don't think it matters). Machine / Browser configuration Safari, Firefox, Chrome and IE9 on dev machine IE7 and IE8 on separate XP Pro VM's (VMWare on dev machine) IE10 and Chrome on Windows 8 VM (VMware on dev machine) Safari, Firefox and Chrome running on a iMac (same network as dev) Safari, Firefox and Chrome running on a couple of Mac Pro's (same network as dev) IE7, IE8, IE9 running on other PC's on the same network as dev machine Development Configuration Multiple virtual hosts for different projects .local fake TLD for development No firewall restrictions on dev machine for Apache Some sites have .htaccess mapping www to non-www Port 80 is open in the dev machine's firewall Problem XAMPP local home page (http://192.168.1.98/xampp/) can be accessed from everywhere, real or virtual, by IP All .local sites can be accessed from the browsers on the dev machine. All .local sites can be accessed form the browsers in the XP VM's. Some .local sites cannot be accessed from IE10 or Chrome on the W8 VM Sites that cannot be accessed from W8 VM have a minimal .htaccess file No .local sites can be accessed from ANY machine (PC or Mac) on the LAN hosts on dev machine (relevant excerpt) 127.0.0.1 site1.local 127.0.0.1 site2.local 127.0.0.1 site3.local 127.0.0.1 site4.local 127.0.0.1 site5.local 127.0.0.1 site6.local 127.0.0.1 site7.local 127.0.0.1 site8.local 127.0.0.1 site9.local 192.168.1.98 site1.local 192.168.1.98 site2.local 192.168.1.98 site3.local 192.168.1.98 site4.local 192.168.1.98 site5.local 192.168.1.98 site6.local 192.168.1.98 site7.local 192.168.1.98 site8.local 192.168.1.98 site9.local httpd-vhosts.conf on dev machine (relevant excerpt) NameVirtualHost *:80 <VirtualHost *:80> ServerName localhost ServerAlias localhost *.localhost.* DocumentRoot D:/xampp/htdocs </VirtualHost> # ======================================== site1.local <VirtualHost *:80> ServerName site1.local ServerAlias site1.local *.site1.local DocumentRoot D:/xampp-sites/site1/public_html ErrorLog D:/xampp-sites/site1/logs/access.log CustomLog D:/xampp-sites/site1/logs/error.log combined <Directory D:/xampp-sites/site1> Options Indexes FollowSymLinks AllowOverride All Require all granted </Directory> </VirtualHost> NOTE: The above <VirtualHost *:80> block is repeated for each of the nine virtual hosts in the file, no sense in posting it here. hosts on all VM's and physical machines on the network (relevant excerpt) 127.0.0.1 localhost ::1 localhost 192.168.1.98 site1.local 192.168.1.98 site2.local 192.168.1.98 site3.local 192.168.1.98 site4.local 192.168.1.98 site5.local 192.168.1.98 site6.local 192.168.1.98 site7.local 192.168.1.98 site8.local 192.168.1.98 site9.local None of the VM's have any firewall blocks on http traffic. They can reach any site on the real Internet. The same is true of the real machines on the network. The biggest puzzle perhaps is that the W8 VM actually DOES reach some of the virtual hosts. It does NOT reach site2, site6 and site 9, all of which have this minimal .htaccess file. .htaccess file <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{HTTP_HOST} !^www\. RewriteRule ^(.*)$ http://www.%{HTTP_HOST}/$1 [R=301,L] </IfModule> Adding this file to any of the virtual hosts that do work on the W8 VM will break the site (only for W8 VM, not the XP VM's) and require a cache flush on the W8 VM before it will see the site again after deleting the file. Regardless of whether a .htaccess file exists or not, no machine on the same LAN can access anything other than the XAMPP home page via IP. Even with hosts files on all machines. I can ping any virtual host from any machine on the network and get a response from the correct IP address. I can't see anything in out Netgear router that might prevent one machine from reaching the other. Besides, once the local hosts file resolves to an ip address that's all that goes out onto the local network. I've gone through an extensive number of posts on both SO and as the result of Google searches. I can't say that I have found anything definitive anywhere.

  Read the article

• My 3D Games crashing in these scenarios

  - by desaivv

  I have a situation here which I am unable to solve. I bought a PC last year March, here are my specs: Intel Core i3 550 @ 3GHz 4 GB RAM @400 MHz XFX GeForce 9500 GT graphics card 1GB @550MHz 500 GB HDD Lately as soon as I load my save game of Skyrim, it crashes. I have been playing Skyrim since I joined Gaming.SE site. Crashes as in the entire scene gets red lines. I can not ALT + TAB back or even CTRL + ALT + DEL either. My only recourse is a hard reset via the power button. Can not take a screen shot either. I have the latest Forceware 296.10 drivers also. This has been happening since the last 2 weeks. I always use Driver Sweeper to clean my old drivers, since that is what XFXForce recommends before installing new drivers. I installed MSI Afterburner lately to see my GPU temperature. My GPU is default, never over-clocked it. In MSI's Afterburner, I can not adjust fan speed. It is greyed out. Also in settings there is no fan tab. With normal Internet browsing it stays at 51 C. Ran Memtest86 over night with level 11. Took about 13 hours, but no errors in my RAM. I even re-installed my OS, with just the 296 drivers. The fan for the GPU does come on. I can play Diablo 2. I can not get past Warcraft 3's menu selection. There WAS some dust in my machine, but I always try and keep everything clean, since in my home town dust is an issue. Always keep cool my entire PC cabinet. My friend came with his functioning graphics card, we bought our PCs at the same time with exact same specifications. His card did not work either. Same problem with the scene freezing with red lines. I did do my research before posting here. That is how I was able to learn about MSI Afterburner, Driver Sweeper, SpeedFan etc. I followed posts on Tom's Hardware too regarding people that had similar problems. One person suggested and was followed by worked as well the suggestion to "Bake the card in an oven". Since I bought it, played Diablo 2 for months, Starcraft 2 campaign for months and Skyrim recently for months. Bought ME3 also. I am at my wits end. I do not know what else to do. I can go out and buy a card, but my friend's card did not work either. I can use the machine for Eclipse or VS2010 development just fine. Just not with 3D gaming. I originally posted this question on Gaming.SE But I was directed here. I have browsed the SU database for my problem and found this, this, and this. But none of these cover my question. My machine is only one year old. Can some experienced superuser(s) shed some light on this scenario? Is it a 3D graphics card problem? Will a brand new card work? What else can I try to pin point the problem? Can it be the Motherboard? Thanks.

  Read the article

• Create a Bootable Ubuntu 9.10 USB Flash Drive

  - by Trevor Bekolay

  The Ubuntu Live CD isn’t just useful for trying out Ubuntu before you install it, you can also use it to maintain and repair your Windows PC. Even if you have no intention of installing Linux, every Windows user should have a bootable Ubuntu USB drive on hand in case something goes wrong in Windows. Creating a bootable USB flash drive is surprisingly easy with a small self-contained application called UNetbootin. It will even download Ubuntu for you! Note: Ubuntu will take up approximately 700 MB on your flash drive, so choose a flash drive with at least 1 GB of free space, formatted as FAT32. This process should not remove any existing files on the flash drive, but to be safe you should backup the files on your flash drive. Put Ubuntu on your flash drive UNetbootin doesn’t require installation; just download the application and run it. Select Ubuntu from the Distribution drop-down box, then 9.10_Live from the Version drop-down box. If you have a 64-bit machine, then select 9.10_Live_x64 for the Version. At the bottom of the screen, select the drive letter that corresponds to the USB drive that you want to put Ubuntu on. If you select USB Drive in the Type drop-down box, the only drive letters available will be USB flash drives. Click OK and UNetbootin will start doing its thing. First it will download the Ubuntu Live CD. Then, it will copy the files from the Ubuntu Live CD to your flash drive. The amount of time it takes will vary depending on your Internet speed, an when it’s done, click on Exit. You’re not planning on installing Ubuntu right now, so there’s no need to reboot. If you look at the USB drive now, you should see a bunch of new files and folders. If you had files on the drive before, they should still be present. You’re now ready to boot your computer into Ubuntu 9.10! How to boot into Ubuntu When the time comes that you have to boot into Ubuntu, or if you just want to test and make sure that your flash drive works properly, you will have to set your computer to boot off of the flash drive. The steps to do this will vary depending on your BIOS – which varies depending on your motherboard. To get detailed instructions on changing how your computer boots, search for your motherboard’s manual (or your laptop’s manual for a laptop). For general instructions, which will suffice for 99% of you, read on. Find the important keyboard keys When your computer boots up, a bunch of words and numbers flash across the screen, usually to be ignored. This time, you need to scan the boot-up screen for a few key words with some associated keys: Boot menu and Setup. Typically, these will show up at the bottom of the screen. If your BIOS has a Boot Menu, then read on. Otherwise, skip to the Hard: Using Setup section. Easy: Using the Boot Menu If your BIOS offers a Boot Menu, then during the boot-up process, press the button associated with the Boot Menu. In our case, this is ESC. Our example Boot Menu doesn’t have the ability to boot from USB, but your Boot Menu should have some options, such as USB-CDROM, USB-HDD, USB-FLOPPY, and others. Try the options that start with USB until you find one that works. Don’t worry if it doesn’t work – you can just restart and try again. Using the Boot Menu does not change the normal boot order on your system, so the next time you start up your computer it will boot from the hard drive as normal. Hard: Using Setup If your BIOS doesn’t offer a Boot Menu, then you will have to change the boot order in Setup. Note: There are some options in BIOS Setup that can affect the stability of your machine. Take care to only change the boot order options. Press the button associated with Setup. In our case, this is F2. If your BIOS Setup has a Boot tab, then switch to it and change the order such that one of the USB options occurs first. There may be several USB options, such as USB-CDROM, USB-HDD, USB-FLOPPY, and others; try them out to see which one works for you. If your BIOS does not have a boot tab, boot order is commonly found in Advanced CMOS Options. Note that this changes the boot order permanently until you change it back. If you plan on only plugging in a bootable flash drive when you want to boot from it, then you could leave the boot order as it is, but you may find it easier to switch the order back to the previous order when you reboot from Ubuntu. Booting into Ubuntu If you set the right boot option, then you should be greeted with the UNetbootin screen. Press enter to start Ubuntu with the default options, or wait 10 seconds for this to happen automatically. Ubuntu will start loading. It should go straight to the desktop with no need for a username or password. And that’s it! From this live desktop session, you can try out Ubuntu, and even install software that is not included in the live CD. Installed software will only last for the duration of your session – the next time you start up the live CD it will be back to its original state. Download UNetbootin from sourceforge.net Similar Articles Productive Geek Tips Create a Bootable Ubuntu USB Flash Drive the Easy WayReset Your Ubuntu Password Easily from the Live CDHow-To Geek on Lifehacker: Control Your Computer with Shortcuts & Speed Up Vista SetupHow To Setup a USB Flash Drive to Install Windows 7Speed up Your Windows Vista Computer with ReadyBoost TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional New Stinger from McAfee Helps Remove ‘FakeAlert’ Threats Google Apps Marketplace: Tools & Services For Google Apps Users Get News Quick and Precise With Newser Scan for Viruses in Ubuntu using ClamAV Replace Your Windows Task Manager With System Explorer Create Talking Photos using Fotobabble

  Read the article

• The Windows Browser Ballot Screen Offers Web Browser Choice to European Users

  - by Matthew Guay

  Since March, our friends across the pond in Europe get to decide which browser they want to install with their Windows OS. Today we thought we would take a look at the ballot choices, some are well known, and others you may not have heard of. Windows users in European countries should start seeing the so called “Browser Ballot Screen” after installing the Windows Update KB976002 (link below). The browser ballot offers a dozen different browsers, including some you’ve likely never heard of.  They each have some unique features, and are all free, and here we take a quick look at each of them. Internet Explorer 8 Internet Explorer is the world’s most used web browser, as it’s bundled with Windows. It also includes several unique features, including Accelerators that make it easy to search or find a map of a location, and InPrivate filtering to directly control what sites can get personal information.  Additionally, it offers great integration with Windows Touch and the new taskbar in Windows 7. IE 8 runs on Windows XP and newer, and is bundled with Windows 7. Mozilla Firefox 3.6 Firefox is the most popular browser other than Internet Explorer.  It is the modern descendant of Netscape, and is loved by web developers for its adherence to web standards, openness, and expandability.  It offers thousands of Add-ons and themes to let you customize it to fit your preferences. The most recent version has added Personas, which are quick, lightweight themes to let you personalize the look your browser. It’s open source, and runs on all modern versions of Windows, Mac OS X, and Linux. Of course thanks to Asian Angel, our resident browser expert, you can check out several articles regarding this popular IE alternative. Google Chrome 4 Google Chrome has gained an impressive amount of market share during its short time in the market. It offers a minimalistic interface and fast speeds with intensive web applications. The address bar is also a search bar, so you can enter a search query or web address and quickly get the information you need. With version 4 you can add a growing number of extensions, personalize it with a variety of stylish themes, and automatically translate foreign websites into your own language. Opera 10.50 Although Opera has been around for over a decade, relatively few users have used it. With the new 10.50 release, Opera has many unique features packed in a sleek UI. It integrates great with Aero and the Windows 7 taskbar, and lets you preview the contents of your websites in the tab bar. It also includes Opera Unite, a small personal web server to make file sharing easy, Opera Turbo to speed up your internet when the connection is slow, and Opera Link to keep all your copies of Opera in sync. It’s a popular browser on many mobile devices, and version 10.50 has a lot of enhancements. Apple Safari 4 Safari is the default browser in Mac OS X, and starting with version 3 it has been available for Windows as well. It’s based on Webkit, the popular new rendering engine that provides great speed and standards compatibility.  Safari 4 lets you browse your browsing history in a unique Coverflow interface, and shows your Top Sites in a fancy, 3D interface.  It’s also great for viewing mobile websites for the iPhone and other mobile devices through Developer Tools. Flock 2.5 Based on the popular Firefox core, Flock brings a multitude of social features to your browsing experience. You can view the latest YouTube videos, Flickr pictures, update your favorite social network, and keep up with your webmail thanks to It’s integration with a wide variety of services. You can even post to your blog through the integrated blog editor. If your time online is mostly spent in social services, this may be a browser you want to check out. Maxthon 2.5 Maxthon is a unique browser that builds on Internet Explorer to bring more features with IE’s rendering. Formerly known as MyIE2, Maxthon was popular for bringing tabbed browsing with IE rendering during the days of IE 6.  Today Maxthon supports a wide range of plugins and skins, so you can customize it however you want. It includes mouse gestures, a web accelerator to speed up pokey internet connections, a content blocker to remove unwanted content from sites, an online account to backup your favorites, and a nice download manager. Avant Browser Another nice browser based on Internet Explorer, Avant brings a wide variety of features in a nice brushed-metal interface. It includes an integrated AutoFill for forms, mouse gestures, customizable skins, and privacy protection features. It also includes a Flash blocker that will only load flash in webpages when you select them. You can also integrate Avant with an online account to store your bookmarks, feeds, settings and passwords online. Sleipnir Sleipnir is a customizable browser meant for advance users that is quite popular in Japan. It’s built on the Trident engine and virtually every aspect of is customizable unlike Internet Explorer.   FlashPeak SlimBrowser SlimBrowser from FlashPeak incorporates a lot of features like Popup Killer, Auto Login, site filtering and more. It’s based on Internet Explorer but offers a lot more customizable options out of the box.   K-meleon This basic browser is light on system resources and based on the Gecko engine. It’s been in development for years on SourceForge, and if you like to tweak virtually any aspect of your browser, this might be a good choice for you.   GreenBrowser GreenBrowser is based on Internet Explorer and is available in several languages. It has a large amount of features out of the box and is light on system resources.   Conclusion The European Union asked for more choices in the web browser they could choose from when installing Windows, and with the Browser Ballot Screen, they certainly get a variety to choose from.  If you’ve tried out some of the lesser known browsers, or think some important ones have been left out, leave a comment and tell us about it. Learn More About the Browser Ballot Screen and Download Alternatives to IE Windows Update KB976002 Similar Articles Productive Geek Tips Set the Default Browser on Ubuntu From the Command LineQuick Tip: Empty Internet Explorer 7 Cache when Browser is ClosedView Hidden Files and Folders in Ubuntu File BrowserSet the Default Browser and Email Client in UbuntuAccess Multiple Browsers from Firefox with Browser View Plus TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Play Music in Chrome by Simply Dragging a File 15 Great Illustrations by Chow Hon Lam Easily Sync Files & Folders with Friends & Family Amazon Free Kindle for PC Download Stretch popurls.com with a Stylish Script (Firefox) OldTvShows.org – Find episodes of Hitchcock, Soaps, Game Shows and more

  Read the article

• How To Skip Commercials in Windows 7 Media Center

  - by DigitalGeekery

  If you use Windows 7 Media Center to record live TV, you’re probably interested in skipping through commercials. After all, a big reason to record programs is to avoid commercials, right? Today we focus on a fairly simple and free way to get you skipping commercials in no time. In Windows 7, the .wtv file format has replaced the dvr-ms file format used in previous versions of Media Center for Recorded TV. The .wtv file format, however, does not work very well with commercial skipping applications.  The Process Our first step will be to convert the recorded .wtv files to the previously used dvr-ms file format. This conversion will be done automatically by WtvWatcher. It’s important to note that this process deletes the original .wtv file after successfully converting to .dvr-ms. Next, we will use DVRMSToolBox with the DTB Addin to handle commercials skipping. This process does not “cut” or remove the commercials from the file. It merely skips the commercials during playback. WtvWatcher Download and install the WTVWatcher (link below). To install WtvWatcher, you’ll need to have Windows Installer 3.1 and .NET Framework 3.5 SP1. If you get the Publisher cannot be verified warning you can go ahead and click Install. We’ve completely tested this app and it contains no malware and runs successfully.   After installing, the WtvWatcher will pop up in the lower right corner of your screen. You will need to set the path to your Recorded TV directory. Click on the button for “Click here to set your recorded TV path…”   The WtvWatcher Preferences window will open…   …and you’ll be prompted to browse for your Recorded TV folder. If you did not change the default location at setup, it will be found at C:\Users\Public\Recorded TV. Click “OK” when finished. Click the “X” to close the Preferences screen. You should now see WtvWatcher begin to convert any existing WTV files.   The process should only take a few minutes per file. Note: If WtvWatcher detects an error during the conversion process, it will not delete the original WTV file.    You will probably want to run WtvWatcher on startup. This will allow WtvWatcher too constantly scan for new .wtv files to convert. There is no setting in the application to run on startup, so you’ll need to copy the WTV icon from your desktop into your Windows start menu “Startup” directory. To do so, click on Start > All Programs, right-click on Startup and click on Open all users. Drag and drop, or cut and paste, the WtvWatcher desktop shortcut into the Startup folder. DVRMSToolBox and DTBAddIn Next, we need to download and install the DVRMSToolBox and the DTBAddIn. These two pieces of software will do the actual commercial skipping. After downloading the DVRMSToolBox zip file, extract it and double-click the setup.exe file.  Click “Next” to begin the installation.   Unless DVRMSToolBox will only be used by Administrator accounts, check the “Modify File Permissions” box. Click “Next.” When you get to the Optional Components window, uncheck Download/Install ShowAnalyzer. We will not be using that application. When the installation is complete, click “Close.”    Next we need to install the DTBAddin. Unzip the download folder and run the appropriate .msi file for your system. It is available in 32 & 64 bit versions. Just double click on the file and take the default options. Click “Finish” when the install is completed. You will then be prompted to restart your computer. After your computer has restarted, open DVRMSToolBox settings by going to Start > All Programs, DVRMSToolBox, and click on DVRMStoMPEGSettings. On the MC Addin tab, make sure that Skip Commercials is checked. It should be by default.   On the Commercial Skip tab, make sure the Auto Skip option is selected. Click “Save.”   If you try to watch recorded TV before the file conversion and commercial indexing process is complete you’ll get the following message pop up in Media Center. If you click Yes, it will start indexing the commercials if WtvWatcher has already converted it to dvr-ms. Now you’re ready to kick back and watch your recorded tv without having to wait through those long commercial breaks. Conclusion The DVRMSToolBox is a powerful and complex application with a multitude of features and utilities. We’ve showed you a quick and easy way to get your Windows Media Center setup to skip commercials. This setup, like virtually all commercial skipping setups, is not perfect. You will occasionally find a commercial that doesn’t get skipped. Need help getting your Windows 7 PC configured for TV? Check out our previous tutorial on setting up live TV in Windows Media Center. Links Download WTV Watcher Download DVRMSToolBox Download DTBAddin Similar Articles Productive Geek Tips Using Netflix Watchnow in Windows Vista Media Center (Gmedia)Increase Skip and Replay Intervals in Windows 7 Media CenterSchedule Updates for Windows Media CenterIntegrate Hulu Desktop and Windows Media Center in Windows 7Add Color Coding to Windows 7 Media Center Program Guide TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet How to Find Your Mac Address Use My TextTools to Edit and Organize Text

  Read the article

• Convert a DVD Movie Directly to AVI with FairUse Wizard 2.9

  - by DigitalGeekery

  Are you looking for a way to backup your DVD movie collection to AVI?  Today we’ll show you how to rip a DVD movie directly to AVI with FairUse Wizard. About FairUse Wizard FairUse Wizard 2.9 uses the DivX, Xvid, or h.264 codec to convert DVD to an AVI file. It comes in both a free version and commercial version. The free, or “Light” version, can create files up 700MB while the commercial version can output a 1400MB file. This will allow you to back up your movies to CD, or even multiple movies on a single DVD. FairUse Wizard states that it does not work on copy protected discs, but we’ve seen it work on all but some of the most recent copy protection. For this tutorial we’re using the free Light Edition to convert a DVD to AVI. They also offer a commercial version that you can get for $29.99 and it offers even more encoding possibilities for converting video to you portable digital devices. Installation and Configuration Download and install FairUse Wizard. (Download link below). Once the install is complete, open FairUse Wizard by going to Start > All Programs >  FairUse Wizard 2 >  FairUse Wizard 2.   FairUse Wizard will open on the new project screen. Select “Create a new project” and type a project name into the text box. This will be used as the file output name.  Ex: A project name of Simpsons Movie will give you an output file of Simpsons Movie.avi.   Next, browse for a destination folder for the output file and temp files. Note that you will need a minimum of 6 GB of free disk space for the conversion process. Note: Much of that 6 GB will be used for temporary files that we will delete after the conversion process.   Click on the Options button at the bottom.   Under Preferences, choose your preferred video codec and file output size. XviD and x264 are installed by default. If you prefer to use DivX, you will have to install it separately. Also note the “Two pass” option. Checking the “Two pass” box will encode your video twice for higher quality, but will take more time. Un-checking the box will speed up the conversion process.   Under Audio track, note that English subtitles are enabled by default, so to remove the subtitles, you will need to change the dropdown list so it shows only a dash (-). You can also select “Use TV Mode” if your primary playback will be on a 4:3 TV screen. Click “Next.” Full Auto Mode vs. Manual Mode You should now be back to the initial screen. Next, we’ll need to determine whether or not we can use “Full Auto Mode” to convert the movie. The difference is that “Full Auto Mode” will automatically perform a few steps that you will otherwise have to do manually. If you choose the “Full Auto Mode” option, FairUse Wizard will look for the video on the DVD with the longest duration and assume it is the chain that it should convert to AVI. It’s possible, however, your disc may contain a few chains of similar size, such as a theatrical cut and director’s cut, and the longest chain may not be the one you wish to convert. Make sure that “Full auto mode” is not checked yet, and click “Next.”   FairUse Wizard will parse the IFO files and display all video chains longer than 60  seconds. In most cases, you will only find that the largest chain is the one closely matching the duration of the movie. In these instances, you can use “Full Auto Mode.” If you find more than one chain that are close in duration to the length of the movie, consult the literature on the DVD case, or search online, to find the actual running time of the movie. If the proper file chain is not the longest chain, you won’t be able to use “Full Auto Mode.”   Full Auto Mode To use “Full Auto Mode,” simply click the “Back” button to return to the initial screen Now, place a check in the “Full auto mode” check box. Click “Next.” You will then be prompted to chose your DVD drive, then click “OK.” FairUse Wizard will parse the IFO files… … and then prompt you to Select your drive that contains the DVD one more time before beginning the conversion process. Click “OK.”   Manual Mode If you cannot (or don’t wish to) use Full Auto Mode, choose the appropriate video chain and click “Next.” FairUse Wizard will first go through the process of indexing the video. Note: If you get a runtime error during this portion of the process, it likely means that FairUse Wizard cannot handle the copy protection, and thus cannot convert the DVD. FairUse Wizard will automatically detect a cropping region. If necessary, you can edit the cropping region by adjusting the cropping region settings to the left. Click “Next.” Next, click “Auto Detect” to choose the proper field combination. Click “OK” on the pop up window that displays your Field Mode. Then click “Next.” This next screen is mainly comprised of settings from the Options screen. You can make changes at this point such as codec or output size. Click “Next” when ready.   Video Conversion Now the video conversion process will begin. This may take a few hours depending on your system’s hardware. Note: There is a check box to “Shutdown computer when done” if you choose to run the conversion overnight or before leaving for work. The first phase will be video encoding… Then the audio… If you chose the “Two Pass” option, your video video will be encoded again on 2nd pass. Then you’re finished. Unfortunately, FairUse Wizard doesn’t clean up after itself very well. After the process is complete, you’ll want to browse to your output directory and delete all the temporary files as they take up a considerable amount of hard drive space. Now you’re ready to enjoy your movie. Conclusion FairUse Wizard is a nice way to backup your DVD movies to good quality .avi files. You can store them on your hard drive, watch them on a media PC, or burn them to disc. Many DVD players even allow for playback of DivX or XviD encoded video from a CD or DVD. For those of you with children, you can burn that AVI file to CD for your kids, and keep your original DVDs stored safely out of harms way. Download Download FairUse Wizard 2.9 LE Similar Articles Productive Geek Tips Kantaris is a Unique Media Player Based on VLCHow to Make/Edit a movie with Windows Movie Maker in Windows VistaAutomatically Mount and View ISO files in Windows 7 Media CenterTune Your ClearType Font Settings in Windows VistaAdd Images and Metadata to Windows 7 Media Center Movie Library TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet How to Find Your Mac Address Use My TextTools to Edit and Organize Text

  Read the article

• Customize your icons in Windows 7 and Vista

  - by Matthew Guay

  Want to change out the icons on your desktop and more?  Personalizing your icons is a great way to make your PC uniquely yours,, and today we show you how to grab unique icons, and default Winnows. to be your own. Change the icon for Computer, Recycle Bin, Network, and your User folder Right-click on the desktop, and select Personalize. Now, click the “Change desktop icons” link on the left sidebar in the Personalization window. The window looks slightly different in Windows Vista, but the link is the same. Select the icon you wish to change, and click the Change Icon button.  In Windows 7, you will also notice a box to choose whether or not to allow themes to change icons, and you can uncheck it if you don’t want themes to change your icon settings. You can select one of the other included icons, or click browse to find the icon you want.  Click Ok when you are finished. Change Folder icons You can easily change the icon on most folders in Windows Vista and 7.  Simply right-click on the folder and select properties. Click the Customize tab, and then click the Change Icon button.  This will open the standard dialog to change your icon, so proceed as normal. This basically just creates a hidden desktop.ini file in the folder containing the following or similar data: [.ShellClassInfo]IconFile=%SystemRoot%\system32\SHELL32.dllIconIndex=20 You could manually create or edit the file if you choose, instead of using the dialogs. Simply create a new text file named desktop.ini with this same information, or edit the existing one.  Change the IconFile line to the location of your icon. If you are pointing to a .ico file you should change the IconIndex line to 0 instead. Note that this isn’t available for all folders, for instance you can’t use this to change the icon for the Windows folder.   In Windows 7, please note that you cannot change the icon of folder inside a library.  So if you are browsing your Documents library and would like to change an icon in that folder, right-click on it and select Open folder location.  Now you can change the icon as above. And if you would like to change a Library’s icon itself, then check out this tutorial: Change Your Windows 7 Library Icons the Easy Way Change the icon of any file type Want to make you files easier to tell apart?  Check out our tutorial on how to simply do this: Change a File Type’s Icon in Windows 7 Change the icon of any Application Shortcut To change the icon of a shortcut on your desktop, start menu, or in Explorer, simply right-click on the icon and select Properties. In the Shortcut tab, click the Change Icon button. Now choose one of the other available icons or click browse to find the icon you want. Change Icons of Running Programs in the Windows 7 taskbar If your computer is running Windows 7, you can customize the icon of any program running in the taskbar!  This only works on applications that are running but not pinned to the taskbar, so if you want to customize a pinned icon you may want to unpin it before customizing it.  But the interesting thing about this trick is that it can customize any icon anything running in the taskbar, including things like Control Panel! Right-click or click and push up to open the jumplist on the icon, and then right-click on the program’s name and select Properties.  Here we are customizing Control Panel, but you can do this on any application icon. Now, click Change Icon as usual. Select an icon you want (We switched the Control Panel icon to the Security Shield), or click Browse to find another icon.  Click Ok when finished, and then close the application window. The next time you open the program (or Control Panel in our example), you will notice your new icon on its taskbar icon. Please note that this only works on applications that are currently running and are not pinned to the taskbar.  Strangely, if the application is pinned to the taskbar, you can still click Properties and change the icon, but the change will not show up. Change the icon on any Drive on your Computer You can easily change the icon on your internal hard drives and portable drives with the free Drive Icon Changer application.  Simply download and unzip the file (link below), and then run the application as administrator by right-clicking on the icon and selecting “Run as administrator”. Now, select the drive that you want to change the icon of, and select your desired icon file. Click Save, and Drive Icon Changer will let you know that the icon has been changed successfully. You will then need to reboot your computer to complete the changes.  Simply click Yes to reboot. Now, our Drive icon is changed from this default image: to a Laptop icon we chose! You can do this to any drive in your computer, or to removable drives such as USB flash drives.  When you change these drives icons, the new icon will appear on any computer you insert the drive into.  Also, if you wish to remove the icon change, simply run the Drive Icon Changer again and remove the icon path. Download Drive Icon Changer This application actually simply creates or edits a hidden Autorun.inf file on the top of your drive.  You can edit or create the file yourself by hand if you’d like; simply include the following information in the file, and save it in the top directory of your drive: [autorun]ICON=[path of your icon] Remove Arrow from shortcut icons Many people don’t like the arrow on the shortcut icon, and there are two easy ways to do this. If you’re running the 32 bit version of Windows Vista or 7, simply use the Vista Shortcut Overlay Remover. If your computer is running the 64 bit version of Windows Vista or 7, use the Ultimate Windows Tweaker instead.  Simply select the Additional Tweaks section, and check the “Remove arrows from Shortcut Icons.” For more info and download links check out this article: Disable Shortcut Icon Arrow Overlay in Windows 7 or Vista Closing: This gives you a lot of ways to customize almost any icon on your computer, so you can make it look just like you want it to.  Stay tuned for more great desktop customization articles from How-to Geek! Similar Articles Productive Geek Tips Change Start Menu to Use Small Icons in Windows 7 or VistaResize Icons Quickly in Windows 7 or Vista ExplorerRoundup: 16 Tweaks to Windows Vista Look & FeelRestore Missing Desktop Icons in Windows 7 or VistaClean Up Past Notification Icons in Windows Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Change DNS servers on the fly with DNS Jumper Live PDF Searches PDF Files and Ebooks Converting Mp4 to Mp3 Easily Use Quick Translator to Translate Text in 50 Languages (Firefox) Get Better Windows Search With UltraSearch Scan News With NY Times Article Skimmer

  Read the article

• 202 blog articles

  - by mprove

  All my blog articles under blogs.oracle.com since August 2005: 202 blog articles Apr 2012 blogs.oracle.com design patch Mar 2012 Interaction 12 - Critique Mar 2012 Typing. Clicking. Dancing. Feb 2012 Desktop Mobility in Hospitals with Oracle VDI /video Feb 2012 Interaction 12 in Dublin - Highlights of Day 3 Feb 2012 Interaction 12 in Dublin - Highlights of Day 2 Feb 2012 Interaction 12 in Dublin - Highlights of Day 1 Feb 2012 Shit Interaction Designers Say Feb 2012 Tips'n'Tricks for WebCenter #3: How to display custom page titles in Spaces Jan 2012 Tips'n'Tricks for WebCenter #2: How to create an Admin menu in Spaces and save a lot of time Jan 2012 Tips'n'Tricks for WebCenter #1: How to apply custom resources in Spaces Jan 2012 Merry XMas and a Happy 2012! Dec 2011 One Year Oracle SocialChat - The Movie Nov 2011 Frank Ludolph's Last Working Day Nov 2011 Hans Rosling at TED Oct 2011 200 Countries x 200 Years Oct 2011 Blog Aggregation for Desktop Virtualization Oct 2011 Oracle VDI at OOW 2011 Sep 2011 Design for Conversations & Conversations for Design Sep 2011 All Oracle UX Blogs Aug 2011 Farewell Loriot Aug 2011 Oracle VDI 3.3 Overview Aug 2011 Sutherland's Closing Remarks at HyperKult Aug 2011 Surface and Subface Aug 2011 Back to Childhood in UI Design Jul 2011 The Art of Engineering and The Engineering of Art Jul 2011 Oracle VDI Seminar - June-30 Jun 2011 SGD White Paper May 2011 TEDxHamburg Live Feed May 2011 Oracle VDI in 3 Minutes May 2011 Space Ship Earth 2011 May 2011 blog moving times Apr 2011 Frozen tag cloud Apr 2011 Oracle: Hardware Software Complete in 1953 Apr 2011 Interaction Design with Wireframes Apr 2011 A guide to closing down a project Feb 2011 Oracle VDI 3.2.2 Jan 2011 free VDI charts Jan 2011 Sun Founders Panel 2006 Dec 2010 Sutherland on Leadership Dec 2010 SocialChat: Efficiency of E20 Dec 2010 ALWAYS ON Desktop Virtualization Nov 2010 12,000 Desktops at JavaOne Nov 2010 SocialChat on Sharing Best Practices Oct 2010 Globe of Visitors Oct 2010 SocialChat about the Next Big Thing Oct 2010 Oracle VDI UX Story - Wireframes Oct 2010 What's a PC anyway? Oct 2010 SocialChat on Getting Things Done Oct 2010 SocialChat on Infoglut Oct 2010 IT Twenty Twenty Oct 2010 Desktop Virtualization Webcasts from OOW Oct 2010 Oracle VDI 3.2 Overview Sep 2010 Blog Usability Top 7 Sep 2010 100 and counting Aug 2010 Oracle'izing the VDI Blogs Aug 2010 SocialChat on Apple Aug 2010 SocialChat on Video Conferencing Aug 2010 Oracle VDI 3.2 - Features and Screenshots Aug 2010 SocialChat: Don't stop making waves Aug 2010 SocialChat: Giving Back to the Community Aug 2010 SocialChat on Learning in Meetings Aug 2010 iPAD's Natural User Interface Jul 2010 Last day for Sun Microsystems GmbH Jun 2010 SirValUse Celebration Snippets Jun 2010 10 years SirValUse - Happy Birthday! Jun 2010 Wim on Virtualization May 2010 New Home for Oracle VDI Apr 2010 Renaissance Slide Sorter Comments Apr 2010 Unboxing Sun Ray 3 Plus Apr 2010 Desktop Virtualisierung mit Sun VDI 3.1 Apr 2010 Blog Relaunch Mar 2010 Social Messaging Slides from CeBIT Mar 2010 Social Messaging Talk at CeBIT Feb 2010 Welcome Oracle Jan 2010 My last presentation at Sun Jan 2010 Ivan Sutherland on Leadership Jan 2010 Learning French with Sun VDI Jan 2010 Learning Danish with Sun Ray Jan 2010 VDI workshop in Nieuwegein Jan 2010 Happy New Year 2010 Jan 2010 On Creating Slides Dec 2009 Best VDI Ever Nov 2009 How to store the Big Bang Nov 2009 Social Enterprise Tools. Beipiel Sun. Nov 2009 Nov-19 Nov 2009 PDF and ODF links on your blog Nov 2009 Q&A on VDI and MySQL Cluster Nov 2009 Zürich next week: Swiss Intranet Summit 09 Nov 2009 Designing for a Sustainable World - World Usabiltiy Day, Nov-12 Nov 2009 How to export a desktop from VDI 3 Nov 2009 Virtualisation Roadshow in the UK Nov 2009 Project Wonderland at EDUCAUSE 09 Nov 2009 VDI Roadshow in Dublin, Nov-26, 2009 Nov 2009 Sun VDI at EDUCAUSE 09 Nov 2009 Sun VDI 3.1 Architecture and New Features Oct 2009 VDI 3.1 is Early-Access Sep 2009 Virtualization for MySQL on VMware Sep 2009 Silpion & 13. Stock Sommerparty Sep 2009 Sun Ray and VMware View 3.1.1 2009-08-31 New Set of Sun Ray Status Icons 2009-08-25 Virtualizing the VDI Core? 2009-08-23 World Usability Day Hamburg 2009 - CfP 2009-07-16 Rising Sun 2009-07-15 featuring twittermeme 2009-06-19 ISC09 Student Party on June-20 /Hamburg 2009-06-18 Before and behind the curtain of JavaOne 2009-06-09 20k desktops at JavaOne 2009-06-01 sweet microblogging 2009-05-25 VDI 3 - Why you need 3 VDI hosts and what you can do about that? 2009-05-21 IA Konferenz 2009 2009-05-20 Sun VDI 3 UX Story - Power of the Web 2009-05-06 Planet of Sun and Oracle User Experience Design 2009-04-22 Sun VDI 3 UX Story - User Research 2009-04-08 Sun VDI 3 UX Story - Concept Workshops 2009-04-06 Localized documentation for Sun Ray Connector for VMware View Manager 1.1 2009-04-03 Sun VDI 3 Press Release 2009-03-25 Sun VDI 3 launches today! 2009-03-25 Sun Ray Connector for VMware View Manager 1.1 Update 2009-03-11 desktop virtualization wiki relaunch 2009-03-06 VDI 3 at CeBIT hall 6, booth E36 2009-03-02 Keyboard layout problems with Sun Ray Connector for VMware VDM 2009-02-23 wikis.sun.com tips & tricks 2009-02-23 Sun VDI 3 is in Early Access 2009-02-09 VirtualCenter unable to decrypt passwords 2009-02-02 Sun & VMware Desktop Training 2009-01-30 VDI at next09? 2009-01-16 Sun VDI: How to use virtual machines with multiple network adapters 2009-01-07 Sun Ray and VMware View 2009-01-07 Hamburg World Usability Day 2008 - Webcasts 2009-01-06 Sun Ray Connector for VMware VDM slides 2008-12-15 mother of all demos 2008-12-08 Build your own Thumper 2008-12-03 Troubleshooting Sun Ray Connector for VMware VDM 2008-12-02 My Roller Tag Cloud 2008-11-28 Sun Ray Connector: SSL connection to VDM 2008-11-25 Setting up SSL and Sun Ray Connector for VMware VDM 2008-11-13 Inspiration for Today and Tomorrow 2008-10-23 Sun Ray Connector for VMware VDM released 2008-10-14 From Sketchpad to ILoveSketch 2008-10-09 Desktop Virtualization on Xing 2008-10-06 User Experience Forum on Xing 2008-10-06 Sun Ray Connector for VMware VDM certified 2008-09-17 Virtual Clouds over Las Vegas 2008-09-14 Bill Verplank sketches metaphors 2008-09-04 End of Early Access - Sun Ray Connector for VMware 2008-08-27 Early Access: Sun Ray Connector for VMware Virtual Desktop Manager 2008-08-12 Sun Virtual Desktop Connector - Insides on Recycling Part 2 2008-07-20 Sun Virtual Desktop Connector - Insides on Recycling Part 3 2008-07-20 Sun Virtual Desktop Connector - Insides on Recycling 2008-07-20 lost in wiki space 2008-07-07 Evolution of the Desktop 2008-06-17 Virtual Desktop Webcast 2008-06-16 Woodstock 2008-06-16 What's a Desktop PC anyway? 2008-06-09 Virtual-T-Box 2008-06-05 Virtualization Glossary 2008-05-06 Five User Experience Principles 2008-04-25 Virtualization News Feed 2008-04-21 Acetylcholinesterase - Second Season 2008-04-18 Acetylcholinesterase - End of Signal 2007-12-31 Produkt-Management ist... 2007-10-22 Usability Verbände, Verteiler und Netzwerke. 2007-10-02 The Meaning is the Message 2007-09-28 Visualization Methods 2007-09-10 Inhouse und Open Source Projekte – Usability verankern und Synergien nutzen 2007-09-03 Der Schwabe Darth Vader entdeckt das Virale Marketing 2007-08-29 Dick Hardt 3.0 on Identity 2.0 2007-08-27 quality of written text depends on the tool 2007-07-27 podcasts for reboot9 2007-06-04 It is the user's itch that need to be scratched 2007-05-25 A duel at reboot9 2007-05-14 Taxonomien und Folksonomien - Tagging als neues HCI-Element 2007-05-10 Dueling Interaction Models of Personal-Computing and Web-Computing 2007-03-01 22.März: Weizenbaum. Rebel at Work. /Filmpremiere Hamburg 2007-02-25 Bruce Sterling at UbiComp 2006 /webcast 2006-11-12 FSOSS 2006 /webcasts 2006-11-10 Highway 101 2006-11-09 User Experience Roundtable Hamburg: EuroGEL 2006 2006-11-08 Douglas Adams' Hyperland (BBC 1990) 2006-10-08 Taxonomien und Folksonomien – Tagging als neues HCI-Element 2006-09-13 Usability im Unternehmen 2006-09-13 Doug does HyperScope 2006-08-26 TED Talks and TechTalks 2006-08-21 Kai Krause über seine Freundschaft zu Douglas Adams 2006-07-20 Rebel At Work: Film Portrait on Weizenbaum 2006-07-04 Gabriele Fischer, mp3 2006-06-07 Dick Hardt at ETech 06 2006-06-05 Weinberger: From Control to Conversation 2006-04-16 Eye Tracking at User Experience Roundtable Hamburg 2006-04-14 dropping knowledge 2006-04-09 GEL 2005 2006-03-13 slide photos of reboot7 2006-03-04 Dick Hardt on Identity 2.0 2006-02-28 User Experience Newsletter #13: Versioning 2006-02-03 Ester Dyson on Choice and Happyness 2006-02-02 Requirements-Engineering im Spannungsfeld von Individual- und Produktsoftware 2006-01-15 User Experience Newsletter #12: Intuition Quiz 2005-11-30 User Experience und Requirements-Engineering für Software-Projekte 2005-10-31 Ivan Sutherland on "Research and Fun" 2005-10-18 Ars Electronica / Mensch und Computer 2005 2005-09-14 60 Jahre nach Memex: Über die Unvereinbarkeit von Desktop- und Web-Paradigma 2005-08-31 reboot 7 2005-06-30

  Read the article

• 6 Ways to Free Up Hard Drive Space Used by Windows System Files

  - by Chris Hoffman

  We’ve previously covered the standard ways to free up space on Windows. But if you have a small solid-state drive and really want more hard space, there are geekier ways to reclaim hard drive space. Not all of these tips are recommended — in fact, if you have more than enough hard drive space, following these tips may actually be a bad idea. There’s a tradeoff to changing all of these settings. Erase Windows Update Uninstall Files Windows allows you to uninstall patches you install from Windows Update. This is helpful if an update ever causes a problem — but how often do you need to uninstall an update, anyway? And will you really ever need to uninstall updates you’ve installed several years ago? These uninstall files are probably just wasting space on your hard drive. A recent update released for Windows 7 allows you to erase Windows Update files from the Windows Disk Cleanup tool. Open Disk Cleanup, click Clean up system files, check the Windows Update Cleanup option, and click OK. If you don’t see this option, run Windows Update and install the available updates. Remove the Recovery Partition Windows computers generally come with recovery partitions that allow you to reset your computer back to its factory default state without juggling discs. The recovery partition allows you to reinstall Windows or use the Refresh and Reset your PC features. These partitions take up a lot of space as they need to contain a complete system image. On Microsoft’s Surface Pro, the recovery partition takes up about 8-10 GB. On other computers, it may be even larger as it needs to contain all the bloatware the manufacturer included. Windows 8 makes it easy to copy the recovery partition to removable media and remove it from your hard drive. If you do this, you’ll need to insert the removable media whenever you want to refresh or reset your PC. On older Windows 7 computers, you could delete the recovery partition using a partition manager — but ensure you have recovery media ready if you ever need to install Windows. If you prefer to install Windows from scratch instead of using your manufacturer’s recovery partition, you can just insert a standard Window disc if you ever want to reinstall Windows. Disable the Hibernation File Windows creates a hidden hibernation file at C:\hiberfil.sys. Whenever you hibernate the computer, Windows saves the contents of your RAM to the hibernation file and shuts down the computer. When it boots up again, it reads the contents of the file into memory and restores your computer to the state it was in. As this file needs to contain much of the contents of your RAM, it’s 75% of the size of your installed RAM. If you have 12 GB of memory, that means this file takes about 9 GB of space. On a laptop, you probably don’t want to disable hibernation. However, if you have a desktop with a small solid-state drive, you may want to disable hibernation to recover the space. When you disable hibernation, Windows will delete the hibernation file. You can’t move this file off the system drive, as it needs to be on C:\ so Windows can read it at boot. Note that this file and the paging file are marked as “protected operating system files” and aren’t visible by default. Shrink the Paging File The Windows paging file, also known as the page file, is a file Windows uses if your computer’s available RAM ever fills up. Windows will then “page out” data to disk, ensuring there’s always available memory for applications — even if there isn’t enough physical RAM. The paging file is located at C:\pagefile.sys by default. You can shrink it or disable it if you’re really crunched for space, but we don’t recommend disabling it as that can cause problems if your computer ever needs some paging space. On our computer with 12 GB of RAM, the paging file takes up 12 GB of hard drive space by default. If you have a lot of RAM, you can certainly decrease the size — we’d probably be fine with 2 GB or even less. However, this depends on the programs you use and how much memory they require. The paging file can also be moved to another drive — for example, you could move it from a small SSD to a slower, larger hard drive. It will be slower if Windows ever needs to use the paging file, but it won’t use important SSD space. Configure System Restore Windows seems to use about 10 GB of hard drive space for “System Protection” by default. This space is used for System Restore snapshots, allowing you to restore previous versions of system files if you ever run into a system problem. If you need to free up space, you could reduce the amount of space allocated to system restore or even disable it entirely. Of course, if you disable it entirely, you’ll be unable to use system restore if you ever need it. You’d have to reinstall Windows, perform a Refresh or Reset, or fix any problems manually. Tweak Your Windows Installer Disc Want to really start stripping down Windows, ripping out components that are installed by default? You can do this with a tool designed for modifying Windows installer discs, such as WinReducer for Windows 8 or RT Se7en Lite for Windows 7. These tools allow you to create a customized installation disc, slipstreaming in updates and configuring default options. You can also use them to remove components from the Windows disc, shrinking the size of the resulting Windows installation. This isn’t recommended as you could cause problems with your Windows installation by removing important features. But it’s certainly an option if you want to make Windows as tiny as possible. Most Windows users can benefit from removing Windows Update uninstallation files, so it’s good to see that Microsoft finally gave Windows 7 users the ability to quickly and easily erase these files. However, if you have more than enough hard drive space, you should probably leave well enough alone and let Windows manage the rest of these settings on its own. Image Credit: Yutaka Tsutano on Flickr     

  Read the article

• How to solve exception_priv _instruction exception while running destop project? [on hold]

  - by Haritha

  While running desktop project im getting exception_priv _instruction how to solve this??? while running this page is coming # # A fatal error has been detected by the Java Runtime Environment: # # EXCEPTION_PRIV_INSTRUCTION (0xc0000096) at pc=0x02f5a92b, pid=3012, tid=3104 # # JRE version: 7.0-b147 # Java VM: Java HotSpot(TM) Client VM (21.0-b17 mixed mode, sharing windows-x86 ) # Problematic frame: # C 0x02f5a92b # # Failed to write core dump. Minidumps are not enabled by default on client versions of Windows # # If you would like to submit a bug report, please visit: # http://bugreport.sun.com/bugreport/crash.jsp # The crash happened outside the Java Virtual Machine in native code. # See problematic frame for where to report the bug. # --------------- T H R E A D --------------- Current thread (0x02f5a800): JavaThread "LWJGL Application" [_thread_in_native, id=3104, stack(0x076f0000,0x07740000)] siginfo: ExceptionCode=0xc0000096 Registers: EAX=0x000df4f0, EBX=0x32afc180, ECX=0x000df4f0, EDX=0x00000020 ESP=0x0773f768, EBP=0x0773f790, ESI=0x32afc180, EDI=0x02f5a800 EIP=0x02f5a92b, EFLAGS=0x00010206 Top of Stack: (sp=0x0773f768) 0x0773f768: 02bd429c 02bd429c 0773f770 32afc180 0x0773f778: 0773f7b8 32b022c8 00000000 32afc180 0x0773f788: 00000000 0773f7a0 0773f7dc 00943187 0x0773f798: 229ec1c0 00948839 69081736 00000000 0x0773f7a8: 089b0048 00000000 00000014 00001406 0x0773f7b8: 00000002 0773f7bc 32afbeb0 0773f7f8 0x0773f7c8: 32b022c8 00000000 32afbf00 0773f7a0 0x0773f7d8: 0773f7f0 0773f81c 00943187 69081736 Instructions: (pc=0x02f5a92b) 0x02f5a90b: 00 43 00 00 00 00 f0 bc 02 e8 00 e9 22 40 f7 73 0x02f5a91b: 07 85 a5 94 00 90 f7 73 07 50 cc a0 6d d8 49 c0 0x02f5a92b: 6d 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x02f5a93b: 00 00 00 00 00 00 00 00 00 08 80 3d 37 00 00 00 Register to memory mapping: EAX=0x000df4f0 is an unknown value EBX=0x32afc180 is an oop {method} - klass: {other class} ECX=0x000df4f0 is an unknown value EDX=0x00000020 is an unknown value ESP=0x0773f768 is pointing into the stack for thread: 0x02f5a800 EBP=0x0773f790 is pointing into the stack for thread: 0x02f5a800 ESI=0x32afc180 is an oop {method} - klass: {other class} EDI=0x02f5a800 is a thread Stack: [0x076f0000,0x07740000], sp=0x0773f768, free space=317k Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code) C 0x02f5a92b j org.lwjgl.opengl.GL11.glVertexPointer(IILjava/nio/FloatBuffer;)V+48 j com.badlogic.gdx.backends.lwjgl.LwjglGL10.glVertexPointer(IIILjava/nio/Buffer;)V+53 j com.badlogic.gdx.graphics.glutils.VertexArray.bind()V+149 j com.badlogic.gdx.graphics.Mesh.bind()V+25 j com.badlogic.gdx.graphics.Mesh.render(IIIZ)V+32 j com.badlogic.gdx.graphics.Mesh.render(III)V+8 j com.badlogic.gdx.graphics.g2d.SpriteBatch.flush()V+197 j com.badlogic.gdx.graphics.g2d.SpriteBatch.switchTexture(Lcom/badlogic/gdx/graphics/Texture;)V+1 j com.badlogic.gdx.graphics.g2d.SpriteBatch.draw(Lcom/badlogic/gdx/graphics/Texture;FFFF)V+33 j sevenseas.game.WorldRenderer.drawBob()V+54 j sevenseas.game.WorldRenderer.render()V+12 j sevenseas.game.GameClass.render(F)V+38 j com.badlogic.gdx.Game.render()V+19 j com.badlogic.gdx.backends.lwjgl.LwjglApplication.mainLoop()V+642 j com.badlogic.gdx.backends.lwjgl.LwjglApplication$1.run()V+27 v ~StubRoutines::call_stub V [jvm.dll+0x122c7e] V [jvm.dll+0x1c9c0e] V [jvm.dll+0x122e73] V [jvm.dll+0x122ed7] V [jvm.dll+0xccd1f] V [jvm.dll+0x14433f] V [jvm.dll+0x171549] C [msvcr100.dll+0x5c6de] endthreadex+0x3a C [msvcr100.dll+0x5c788] endthreadex+0xe4 C [kernel32.dll+0xb713] GetModuleFileNameA+0x1b4 Java frames: (J=compiled Java code, j=interpreted, Vv=VM code) j org.lwjgl.opengl.GL11.nglVertexPointer(IIIJJ)V+0 j org.lwjgl.opengl.GL11.glVertexPointer(IILjava/nio/FloatBuffer;)V+48 j com.badlogic.gdx.backends.lwjgl.LwjglGL10.glVertexPointer(IIILjava/nio/Buffer;)V+53 j com.badlogic.gdx.graphics.glutils.VertexArray.bind()V+149 j com.badlogic.gdx.graphics.Mesh.bind()V+25 j com.badlogic.gdx.graphics.Mesh.render(IIIZ)V+32 j com.badlogic.gdx.graphics.Mesh.render(III)V+8 j com.badlogic.gdx.graphics.g2d.SpriteBatch.flush()V+197 j com.badlogic.gdx.graphics.g2d.SpriteBatch.switchTexture(Lcom/badlogic/gdx/graphics/Texture;)V+1 j com.badlogic.gdx.graphics.g2d.SpriteBatch.draw(Lcom/badlogic/gdx/graphics/Texture;FFFF)V+33 j sevenseas.game.WorldRenderer.drawBob()V+54 j sevenseas.game.WorldRenderer.render()V+12 j sevenseas.game.GameClass.render(F)V+38 j com.badlogic.gdx.Game.render()V+19 j com.badlogic.gdx.backends.lwjgl.LwjglApplication.mainLoop()V+642 j com.badlogic.gdx.backends.lwjgl.LwjglApplication$1.run()V+27 v ~StubRoutines::call_stub --------------- P R O C E S S --------------- Java Threads: ( => current thread ) 0x003d6c00 JavaThread "DestroyJavaVM" [_thread_blocked, id=3240, stack(0x008c0000,0x00910000)] =>0x02f5a800 JavaThread "LWJGL Application" [_thread_in_native, id=3104, stack(0x076f0000,0x07740000)] 0x02bcf000 JavaThread "Service Thread" daemon [_thread_blocked, id=2612, stack(0x02e00000,0x02e50000)] 0x02bc1000 JavaThread "C1 CompilerThread0" daemon [_thread_blocked, id=2776, stack(0x02db0000,0x02e00000)] 0x02bbf400 JavaThread "Attach Listener" daemon [_thread_blocked, id=2448, stack(0x02d60000,0x02db0000)] 0x02bbe000 JavaThread "Signal Dispatcher" daemon [_thread_blocked, id=1764, stack(0x02d10000,0x02d60000)] 0x02bb8000 JavaThread "Finalizer" daemon [_thread_blocked, id=3864, stack(0x02cc0000,0x02d10000)] 0x02bb3400 JavaThread "Reference Handler" daemon [_thread_blocked, id=2424, stack(0x02c70000,0x02cc0000)] Other Threads: 0x02bb1800 VMThread [stack: 0x02c20000,0x02c70000] [id=3076] 0x02bd1000 WatcherThread [stack: 0x02e50000,0x02ea0000] [id=3276] VM state:not at safepoint (normal execution) VM Mutex/Monitor currently owned by a thread: None Heap def new generation total 4928K, used 2571K [0x229c0000, 0x22f10000, 0x27f10000) eden space 4416K, 46% used [0x229c0000, 0x22bc2e38, 0x22e10000) from space 512K, 100% used [0x22e90000, 0x22f10000, 0x22f10000) to space 512K, 0% used [0x22e10000, 0x22e10000, 0x22e90000) tenured generation total 10944K, used 634K [0x27f10000, 0x289c0000, 0x329c0000) the space 10944K, 5% used [0x27f10000, 0x27faea60, 0x27faec00, 0x289c0000) compacting perm gen total 12288K, used 1655K [0x329c0000, 0x335c0000, 0x369c0000) the space 12288K, 13% used [0x329c0000, 0x32b5dc58, 0x32b5de00, 0x335c0000) ro space 10240K, 42% used [0x369c0000, 0x36dfc660, 0x36dfc800, 0x373c0000) rw space 12288K, 53% used [0x373c0000, 0x37a38180, 0x37a38200, 0x37fc0000) Code Cache [0x00940000, 0x009d8000, 0x02940000) total_blobs=305 nmethods=80 adapters=158 free_code_cache=32183Kb largest_free_block=32955904 Dynamic libraries: 0x00400000 - 0x0042f000 C:\Program Files\Java\jre7\bin\javaw.exe 0x7c900000 - 0x7c9af000 C:\WINDOWS\system32\ntdll.dll 0x7c800000 - 0x7c8f6000 C:\WINDOWS\system32\kernel32.dll 0x77dd0000 - 0x77e6b000 C:\WINDOWS\system32\ADVAPI32.dll 0x77e70000 - 0x77f02000 C:\WINDOWS\system32\RPCRT4.dll 0x77fe0000 - 0x77ff1000 C:\WINDOWS\system32\Secur32.dll 0x7e410000 - 0x7e4a1000 C:\WINDOWS\system32\USER32.dll 0x77f10000 - 0x77f59000 C:\WINDOWS\system32\GDI32.dll 0x773d0000 - 0x774d3000 C:\WINDOWS\WinSxS\x86_Microsoft.Windows.Common-Controls_6595b64144ccf1df_6.0.2600.5512_x-ww_35d4ce83\COMCTL32.dll 0x77c10000 - 0x77c68000 C:\WINDOWS\system32\msvcrt.dll 0x77f60000 - 0x77fd6000 C:\WINDOWS\system32\SHLWAPI.dll 0x76390000 - 0x763ad000 C:\WINDOWS\system32\IMM32.DLL 0x629c0000 - 0x629c9000 C:\WINDOWS\system32\LPK.DLL 0x74d90000 - 0x74dfb000 C:\WINDOWS\system32\USP10.dll 0x78aa0000 - 0x78b5e000 C:\Program Files\Java\jre7\bin\msvcr100.dll 0x6d940000 - 0x6dc61000 C:\Program Files\Java\jre7\bin\client\jvm.dll 0x71ad0000 - 0x71ad9000 C:\WINDOWS\system32\WSOCK32.dll 0x71ab0000 - 0x71ac7000 C:\WINDOWS\system32\WS2_32.dll 0x71aa0000 - 0x71aa8000 C:\WINDOWS\system32\WS2HELP.dll 0x76b40000 - 0x76b6d000 C:\WINDOWS\system32\WINMM.dll 0x76bf0000 - 0x76bfb000 C:\WINDOWS\system32\PSAPI.DLL 0x6d8d0000 - 0x6d8dc000 C:\Program Files\Java\jre7\bin\verify.dll 0x6d370000 - 0x6d390000 C:\Program Files\Java\jre7\bin\java.dll 0x6d920000 - 0x6d933000 C:\Program Files\Java\jre7\bin\zip.dll 0x6cec0000 - 0x6cf42000 C:\Documents and Settings\7stl0225\Local Settings\Temp\libgdx7stl0225\37fe1abc\gdx.dll 0x10000000 - 0x1004c000 C:\Documents and Settings\7stl0225\Local Settings\Temp\libgdx7stl0225\52d76f2b\lwjgl.dll 0x5ed00000 - 0x5edcc000 C:\WINDOWS\system32\OPENGL32.dll 0x68b20000 - 0x68b40000 C:\WINDOWS\system32\GLU32.dll 0x73760000 - 0x737ab000 C:\WINDOWS\system32\DDRAW.dll 0x73bc0000 - 0x73bc6000 C:\WINDOWS\system32\DCIMAN32.dll 0x77c00000 - 0x77c08000 C:\WINDOWS\system32\VERSION.dll 0x070b0000 - 0x07115000 C:\DOCUME~1\7stl0225\LOCALS~1\Temp\libgdx7stl0225\52d76f2b\OpenAL32.dll 0x7c9c0000 - 0x7d1d7000 C:\WINDOWS\system32\SHELL32.dll 0x774e0000 - 0x7761d000 C:\WINDOWS\system32\ole32.dll 0x5ad70000 - 0x5ada8000 C:\WINDOWS\system32\uxtheme.dll 0x76fd0000 - 0x7704f000 C:\WINDOWS\system32\CLBCATQ.DLL 0x77050000 - 0x77115000 C:\WINDOWS\system32\COMRes.dll 0x77120000 - 0x771ab000 C:\WINDOWS\system32\OLEAUT32.dll 0x73f10000 - 0x73f6c000 C:\WINDOWS\system32\dsound.dll 0x76c30000 - 0x76c5e000 C:\WINDOWS\system32\WINTRUST.dll 0x77a80000 - 0x77b15000 C:\WINDOWS\system32\CRYPT32.dll 0x77b20000 - 0x77b32000 C:\WINDOWS\system32\MSASN1.dll 0x76c90000 - 0x76cb8000 C:\WINDOWS\system32\IMAGEHLP.dll 0x72d20000 - 0x72d29000 C:\WINDOWS\system32\wdmaud.drv 0x72d10000 - 0x72d18000 C:\WINDOWS\system32\msacm32.drv 0x77be0000 - 0x77bf5000 C:\WINDOWS\system32\MSACM32.dll 0x77bd0000 - 0x77bd7000 C:\WINDOWS\system32\midimap.dll 0x73ee0000 - 0x73ee4000 C:\WINDOWS\system32\KsUser.dll 0x755c0000 - 0x755ee000 C:\WINDOWS\system32\msctfime.ime 0x69000000 - 0x691a9000 C:\WINDOWS\system32\sisgl.dll 0x73b30000 - 0x73b45000 C:\WINDOWS\system32\mscms.dll 0x73000000 - 0x73026000 C:\WINDOWS\system32\WINSPOOL.DRV 0x66e90000 - 0x66ed1000 C:\WINDOWS\system32\icm32.dll 0x07760000 - 0x0778d000 C:\Program Files\WordWeb\WHook.dll 0x74c80000 - 0x74cac000 C:\WINDOWS\system32\OLEACC.dll 0x76080000 - 0x760e5000 C:\WINDOWS\system32\MSVCP60.dll VM Arguments: jvm_args: -Dfile.encoding=Cp1252 java_command: sevenseas.game.MainDesktop Launcher Type: SUN_STANDARD Environment Variables: PATH=C:/Program Files/Java/jre7/bin/client;C:/Program Files/Java/jre7/bin;C:/Program Files/Java/jre7/lib/i386;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Program Files\Java\jdk1.7.0\bin;C:\eclipse; USERNAME=7stl0225 OS=Windows_NT PROCESSOR_IDENTIFIER=x86 Family 15 Model 4 Stepping 1, GenuineIntel --------------- S Y S T E M --------------- OS: Windows XP Build 2600 Service Pack 3 CPU:total 1 (1 cores per cpu, 1 threads per core) family 15 model 4 stepping 1, cmov, cx8, fxsr, mmx, sse, sse2, sse3 Memory: 4k page, physical 2031088k(939252k free), swap 3969920k(3011396k free) vm_info: Java HotSpot(TM) Client VM (21.0-b17) for windows-x86 JRE (1.7.0-b147), built on Jun 27 2011 02:25:52 by "java_re" with unknown MS VC++:1600 time: Sat Oct 26 12:35:14 2013 elapsed time: 0 seconds

  Read the article

< Previous Page | 251 252 253 254 255 256 257 258 259 260 261 262  | Next Page >