Search Results

Search found 6545 results on 262 pages for 'usb hub'.

Page 255/262 | < Previous Page | 251 252 253 254 255 256 257 258 259 260 261 262  | Next Page >

  • Recover harddrive data

    - by gameshints
    I have a dell laptop that recently "died" (It would get the blue screen of death upon starting) and the hard drive would make a weird cyclic clicking noises. I wanted to see if I could use some tools on my linux machine to recover the data, so I plugged it into there. If I run "fdisk" I get: Disk /dev/sdb: 20.0 GB, 20003880960 bytes 64 heads, 32 sectors/track, 19077 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Disk identifier: 0x64651a0a Disk /dev/sdb doesn't contain a valid partition table Fine, the partition table is messed up. However if I run "testdisk" in attempt to fix the table, it freezes at this point, making the same cyclical clicking noises: Disk /dev/sdb - 20 GB / 18 GiB - CHS 19078 64 32 Analyse cylinder 158/19077: 00% I don't really care about the hard drive working again, and just the data, so I ran "gpart" to figure out where the partitions used to be. I got this: dev(/dev/sdb) mss(512) chs(19077/64/32)(LBA) #s(39069696) size(19077mb) * Warning: strange partition table magic 0x2A55. Primary partition(1) type: 222(0xDE)(UNKNOWN) size: 15mb #s(31429) s(63-31491) chs: (0/1/1)-(3/126/63)d (0/1/32)-(15/24/4)r hex: 00 01 01 00 DE 7E 3F 03 3F 00 00 00 C5 7A 00 00 Primary partition(2) type: 007(0x07)(OS/2 HPFS, NTFS, QNX or Advanced UNIX) (BOOT) size: 19021mb #s(38956987) s(31492-38988478) chs: (4/0/1)-(895/126/63)d (15/24/5)-(19037/21/31)r hex: 80 00 01 04 07 7E FF 7F 04 7B 00 00 BB 6F 52 02 So I tried to mount just to the old NTFS partition, but got an error: sudo mount -o loop,ro,offset=16123904 -t ntfs /dev/sdb /mnt/usb NTFS signature is missing. Ugh. Okay. But then I tried to get a raw data dump by running dd if=/dev/sdb of=/home/erik/brokenhd skip=31492 count=38956987 But the file got up to 59885568 bytes, and made the same cyclical clicking noises. Obviously there is a bad sector, but I don't know what to do about it! The data is still there... if I view that 57MB file in textpad... I can see raw data from files. How can I get my data back? Thanks for any suggestions, Solution: I was able to recover about 90% of my data: Froze harddrive in freezer Used Ddrescue to make a copy of the drive Since Ddrescue wasn't able to get enough of my drive to use testdisk to recover my partitions/file system, I ended up using photorec to recover most of my files

    Read the article

  • Hard freeze on new computer

    - by mphair
    OCZ Gold 3x2GB 240-Pin DDR3 SDRAM PC312800 Palit NE5T240SFHD01 GeForce GT240 1GB 128-bit GDDR5 ASUS P7P55D-E LGA 1156 P55 SATA 6Gb/s USB 3.0 ATX Intel Motherboard Intel Core i7-860 Lynnfield 2.8GHz 8MB L3 Cache LGA 1156 95W Quad-Core Processor SAMSUNG 22X Optical drive (DVD+-R/RW) CORSAIR CMPSU-620HX 620W ATX12V V2.2 Windows 7 Ultimate x64 Brand new system (got it from newegg two days ago) and it booted up and installed windows and ran for a day just fine. Yesterday, I boot it up in the afternoon and run various games at full graphics for most of the day. I turn on WoW and play for a few hours and it hard stalls. No numlock switching, no mouse feedback but nothing going wrong on the screen. No BSOD. I wait a bit to see if the stall is just a temporary one, but then force shutdown the computer. Upon reboot, everything seems fine, windows sees that it didn't shut down properly but I go into normal boot and restart WoW. I'm able to load it up and start running around when it freezes again. This time when I restart, it doesn't even get to BIOS. It starts (power goes on) and it just hangs with no output to the monitors. I shut it off and went to bed. This morning, I turned it on and went into BIOS setup. I'm not terribly experienced with messing with BIOS settings but I checked over them the best I could. Everything seems fine so I boot into windows and browse the internet for a bit looking for a solution, hard freeze within 10 minutes. I restart and go into BIOS and check the CPU temperature, 40c. I'm kinda stumped here. Some people say it might be a memory issue, but why would it take so long for it to come up? Could it have been slowly accessing one memory stick at a time and then it just got to a bad one and that's what is causing it to fail? It seems odd that I don't get a BSOD from a hardware failure. Having the screen just halt with no input or output change seems like a software thing to me. Any thoughts?

    Read the article

  • Bypassing "Found New Hardware Wizard" / Setting Windows to Install Drivers Automatically

    - by Synetech inc.
    Hi, My motherboard finally died after the better part of a decade, so I bought a used system. I put my old hard-drive and sound-card in the new system, and connected my old keyboard and mouse (the rest of the components—CPU, RAM, mobo, video card—are from the new system). I knew beforehand that it would be a challenge to get Windows to boot and install drivers for the new hardware (particularly since the foundational components are new), but I am completely unable to even attempt to get through the work of installing drivers for things like the video card because the keyboard and mouse won't work (they do work, in the BIOS screen, in DOS mode, in Windows 7, in XP's boot menu, etc., just not in Windows XP itself). Whenever I try to boot XP (in normal or safe mode), I get a bunch of balloons popping up for all the new hardware detected, and a New Hardware Found Wizard for Processor (obviously it has to install drivers for the lowest-level components on up). Unfortunately I cannot click Next since the keyboard and mouse won't work yet because the motherboard drivers (for the PS/2 or USB ports) are not yet installed. I even tried a serial mouse, but to no avail—again, it does work in DOS, 7, etc., but not XP because it doesn't have the serial port driver installed. I tried mounting the SOFTWARE and SYSTEM hives under Windows 7 in order to manually set the "unsigned drivers warning" to ignore (using both of the driver-signing policy settings that I found references to). That didn't work; I still get the wizard. They are not even fancy, proprietary, third-party, or unsigned drivers. They are drivers that come with Windows—as the drivers for CPU, RAM, IDE controller, etc. tend to be. And the keyboard and mouse drivers are the generic ones at that (but like I said, those are irrelevant since the drivers for the ports that they are connected to are not yet installed). Obviously at some point in time over the past several years, a setting got changed to make Windows always prompt me when it detects new hardware. (It was also configured to show the Shutdown Event Tracker on abnormal shutdowns, so I had to turn that off so that I could even see the desktop.) Oh, and I tried deleting all of the PNF files so that they get regenerated, but that too did not help. Does anyone know how I can reset Windows to at least try to automatically install drivers for new hardware before prompting me if it fails? Conversely, does anyone know how exactly one turns off automatic driver installation (and prompt with the wizard)? Thanks a lot.

    Read the article

  • File/printer sharing issues on network with multiple OSes

    - by DanZ
    My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

    Read the article

  • Suggestions for splitting server roles amongst Hyper-V virtual servers / RAID6 or RAID10? / AppAssure

    - by Anon
    We have 2 Hyper-V hosts at present running 1 virtual server that was converted from a physical box running all roles. My plan is to split the roles over various virtual machines, upgrading to the latest software versions as I go, and use the backup server as a standby in case the main server fails. AppAssure backup software has a feature called Virtual Standby, so the VHD's can be ready to be fired up on the backup server if necessary. Off-site backups will be done via external USB drive for now. I'm just seeking some input/suggestions into how I'm planning to split the roles out amongst various virtual servers. Also, I'm curious how to setup the storage on the servers. We do not have any NAS's, SAN'S or any budget for this. What would the best RAID level be to use? I'm thinking either RAID6 (which is currently used) however I'm concerned about the write speeds, or RAID10 but again I'm worried that I can only lose 1 drive (from the same mirror) as opposed to any 2 with RAID6. I realise I have a hot swap for this, but what if a further drive fails during a rebuild? Is the write penalty of RAID6 worth the extra reliability over RAID10? Or will it be too slow with all the roles I am planning, therefore RAID10 is my only real option? The reason for the needed redundancy is I am the only technician and I'm not always on-site. Options I've considered: 1) 5 drives in RAID6 set, 200gb for host OS, rest for VM storage. 1 drive for hot swap - this is how it is currently setup 2) 4 drives in RAID10 set, 200gb for host OS, rest for VM storage. 2 drives for hot swap 3) 4 drives in RAID10 set for VM storage, 2 drives in RAID1 set for host OS. No drives for hot swap - While this is probably the best option with the amount of drives I have, I don't like the idea of having no hot swap 4) 3 drives in RAID6 set for VM storage, 2 drives in RAID1 set for host OS. 1 drive for hot swap All options give us enough storage capacity for our files, etc. We don't have any budget for extra drives or extra hot swap HD chassis for the servers. We have about 70 clients and about 150 users. MAIN SERVER Intel Xeon 5520 @ 2.27 GHz (2 processors) 16GB RAM 6 x 1TB Seagate Barracuda ES.2 Enterprise SATA drives Intel SRCSATAWB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: DC01 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM DC02 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM Member Server - DHCP server, File server, Print server - 1GB RAM SCCM Member Server - 4GB RAM Third Party Software Member Server - A/V server, Ticketing software, etc - 4GB RAM Exchange 2007 - 4GB RAM - however we are probably migrating to a hosted solution, therefore freeing up resources BACKUP SERVER Intel Xeon E5410 @ 2.33GHz (2 processors) 16GB RAM 6 x 2TB WD RE4 SATA drives Intel SRCSASRB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: AppAssure backup software - 8GB RAM

    Read the article

  • Unable to burn Windows ISO from Fedora

    - by user331947
    First of all, English is not my native tongue, so apologies for any mistakes. My computer recently started prompting that it can't launch Windows successfully. So I just choose start Windows normally. Then, I found that the startup freezes at the Windows screen (before the login prompt). I have tried rebooting several times and get the same results. So I just gave up. After few days, I tried to boot up my laptop again. This time it got to the desktop, but it's extremely slow and the icons on my Desktop don't show up. I decided to format the Windows partition and reinstall a new one. (It is usually faster that way since I kept my 400GB+ data on aother partition and programs and the rest in the same partition as Windows). The thing is I get the Windows disc at the moment (Traveling aboard). But I have a Windows 7 disc image on my hard disk. So, I downloaded Ubuntu 14.04 LTS, made a Live USB, and then try to burn the image from Ubuntu. But the program just freezes and I don't know why. I tried several times and it's still the same. So I tried using Fedora instead, just to see if it will work. The Disk Image Writer report something like this. Error unmounting /dev/dm-0: Command-line `umount "/dev/dm-0"' exited with non-zero exit status 32: umount: /: target is busy (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1).) (udisks-error-quark, 14) Also, I tried installing linux on the windows partition. The installation program freezes (both Ubuntu and Fedora). So, I thought that maybe something are wrong with my hard disk. I seek the solution on the internet and found that gparted can be used to format a partition. And it also froze at "Searching /dev/sda/ partition ...". I'm using Lenovo Y570. Spec below. http://www.notebookreview.com/notebookreview/lenovo-ideapad-y570-review-a-lenovo-bestseller/3/ Can anyone suggest a next step in diagnosing and fixing this problem? Thanks in advance.

    Read the article

  • Building a Mac/PC Network in a Dorm with Network Restrictions

    - by user70340
    I have been a Windows XP user for the last few years, but I recently bought a 15'' MacBook Pro for research purposes. I would like to set up a no-hassle Mac/PC Network at home so that I can access the internet on both computers and hardware between computers (i.e. a harddrive, or a mouse/keyboard with Synergy). Unfortunately, I live in a dorm with silly network restrictions so a solution is not straightforward. In particular: The dorm has a wired and wireless network, both which provide an internet connection. The wired network provides way faster internet (download speeds of 15 MB/s vs. 2 MB/s on wireless), so I would like to somehow exploit this, at least on my PC for Bittorrent :) Multiple devices can connect to the wireless network, but cannot "see" each other on the network (so software like Synergy would not work). Only 1 MAC address can connect to the wired network at a time. Ideally I would just connect a wireless router to the wired network and then have both the Mac and the PC on that, but the 1 MAC address restriction will not allow the both computer to access the internet simultaneously. I cannot think of a way to bypass this restriction (though I'm not network savvy), so I am planning to create a private no-internet network to allow the devices to see each other and share hardware. Here are some thoughts. I would appreciate any feedback at all! If I build a private wireless network: (first choice) I will use a wireless router that is not connected to the internet. My PC and Mac will be connected to each other wirelessly. I can then connect the PC to the internet via a wired network, but then the Mac will not have internet access as its wireless card is already in use. In this case, could I stream internet access from the PC to the Mac via the wireless network? Or could I buy a USB wireless card for the Mac so that it can connect to both my private network and the dorm network? If I build a private wired network: (second choice) Then both the PC and the Mac will connect to the internet wirelessly, which means I cannot take advantage of the faster download speeds.

    Read the article

  • Loss of wireless network connectivity when playing video via HDMI cable

    - by Jeff Fohl
    Hi Folks - New to Super User, so I hope this question fits in with the guidelines. Very strange problem I am having, and I am at a loss as to how to continue troubleshooting this one. The basic problem is that when I attempt to watch streamed video on a particular display device (an Optoma HD180 projector), my network connectivity drops like a stone to barely measurable levels. This is my setup: I have a Dell H2C 730x running Windows 7 64bit. This particular computer has two ATI Radeon HD 4800 video cards. I have two Samsung 22" monitors connected to one card, and an Optoma HD180 digital projector connected to the other card via an HDMI cable. My internet connection is normally a reliable 6Mbps. The problem I am having occurs when I stream video (or even just browse the web) on the Optoma Projector. When I do this, my internet connection drops to practically zero (just a few kilobits per second). When I move the browser away from the projector, and over to one of my Samsung monitors, the internet connection comes right back. Note that the Optoma projector is on and enabled as a third monitor all this time. I can move the mouse around on the projector without triggering the problem. I tried pinging my router when I was playing a movie on one of the monitors, and I get a 1 millisecond response. However, when I have the movie playing on the Optoma projecter, pinging the router gives me response times in the hundreds of milliseconds, or times out completely. So, it clearly is something local to my machine - and not some sort of throttling occurring down the line. I would think that it is possibly something to do with the HDMI driver conflicting somehow with my network driver (which is a USB-based wireless connection). This one has me really stumped. Anyone have any ideas? EDIT: I am now leaning towards the possibility that the HDMI cable is somehow interfering with the wireless network, when large amounts of data are being pushed through the cable. Is this possible?

    Read the article

  • Seriousness of a "Smart" disk error. How long will it last?

    - by Workshop Alex
    I have an 1 TB data disk and the bios and Windows are reporting a "Smart" error. At least, I get a Smart event but it doesn't indicate how serious the failure could be. My system is about 6 months old, including the disk so the warranty will cover the damage. Unfortunately, I lack a second disk of 1 TB in size which I can use to make a full backup. The most important data on this disk is safe, but there's a lot of work data which can be regenerated but this would cost a lot of time. So I ordered an USB disk of 1 TB which will arrive in three days. By then I can make a full backup of the data and afterwards, it can crash. But will the disk live that long? (Well, I won't use the PC as long as I can't make a backup.) How serious is such a Smart event? I know it's serious enough to have it replaced, but will it live for another week or could it die any moment?Update: I purchased an 1 TB external disk and spent most of the day making a backup of the 1 TB disk. It survived that. I then received a new disk, since it was still under warranty and replaced the hard disk. Then I had to spend most of a day again to put back the backup. I need to send back the faulty disk and now have an additional external disk, which could always be practical. :-) The Smart Error report did not cause any failures on the original disk. I won't advise to ignore these warnings, but the disk still has enough life in it to last a few more days. (Just make sure you have a good back-up.) And oh, the horror of having to make a complete backup such a huge disk. :-) If your data is important, make sure you have something that supports incremental backups and lots of space. (In my case, the data wasn't very important, just practical to have on-disk together.)

    Read the article

  • How can I reverse mouse movement (X & Y axis) system-wide? (Win 7 x64)

    - by Scivitri
    Short Version I'm looking for a way to reverse the X and Y mouse axis movements. The computer is running Windows 7, x64 and Logitech SetPoint 6.32. I would like a system-level, permanent fix; such as a mouse driver modification or a registry tweak. Does anyone know of a solid way of implementing this, or how to find the registry values to change this? I'll settle quite happily for how to enable the orientation feature in SetPoint 6.32 for mice as well as trackballs. Long Version People seem never to understand why I would want this, and I commonly hear "just use the mouse right-side up!" advice. Dyslexia is not something which can be cured by "just reading things right." While I appreciate the attempts to help, I'm hoping some background may help people understand. I have a user with an unusual form of dyslexia, for whom mouse movements are backward. If she wants to move her cursor left, she will move the mouse right. If she wants the cursor to move up, she'll move the mouse down. She used to hold her mouse upside-down, which makes sophisticated clicking difficult, is terrible for ergonomics, and makes multi-button mice completely useless. In olden times, mouse drivers included an orientation feature (typically a hot-air balloon you dragged upward to set the mouse movement orientation) which could be used to set the relationship between mouse movement and cursor movement. Several years ago, mouse drivers were "improved" and this feature has since been limited to trackballs. After losing the orientation feature she went back to upside-down mousing for a bit, until finding UberOptions, a tweak for Logitech SetPoint, which would enable all features for all pointing devices. This included the orientation feature. And there was much rejoicing. Now her mouse has died, and current Logitech mice require a newer version of SetPoint for which UberOptions has not been updated. We've also seen MAF-Mouse (the developer indicated the version for 64-bit Windows does not support USB mice, yet) and Sakasa (while it works, commentary on the web indicate it tends to break randomly and often. It's also just a running program, so not system-wide.). I have seen some very sophisticated registry hacks. For example, I used to use a hack which would change the codes created by the F1-F12 keys when the F-Lock key was invented and defaulted to screwing my keyboard up. I'm hoping there's a way to flip X and Y in the registry; or some other, similar, system-level tweak out there. Another solution could be re-enabling the orientation feature for mice, as well as trackballs. It's very frustrating that input device drivers include the functionality we desperately need for an accessibilty concern, but it's been disabled in the name of making the drivers more idiot-proof.

    Read the article

  • Thinkpad speaker turns mute - Linux Codec issue?

    - by Curlew
    At some point a few days ago the speakers on my Lenovo Thinkpad T410 (Model number: 2537A11) suddenly stopped working randomly. This error happens every time I watch a video or listen to a music file. The sound just abruptly stops. At the moment, I can't produce a single sound no matter what I do. I am using Debian GNU/Linux on this laptop and there doesn't appear to be anything else wrong (the fan is working, no abnormal heat (staying around ~40°C), no other obvious errors or problems). Here is the output of a nice program someone pointed me to: martin@martin:~/Downloads$ sudo python run.py --monitor Using temporary directory: /dev/shm/hda-analyzer You may remove this directory when finished or if you like to download the most recent copy of hda-analyzer tool. Downloading file hda_analyzer.py Downloading file hda_guilib.py Downloading file hda_codec.py Downloading file hda_proc.py Downloading file hda_graph.py Downloading file hda_mixer.py Downloaded all files, executing hda_analyzer.py Watching 1 cards ====================================== Sound is working normally and then it stops and the following lines appear: Diff for codec 0/0 (0x14f15069): --- +++ @@ -164,17 +164,17 @@ Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Pincap 0x00000010: OUT Pin Default 0x901701f0: [Fixed] Speaker at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT - Power: setting=D0, actual=D0 + Power: setting=D3, actual=D3 Connection: 2 0x10* 0x11 Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE And now there is also an error in the dmesg output hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. I changed the bdl_pos_adj to various numbers (-1, 0, 64, 1024) and either there is no change at all or dmesg reports that the adjustment is too big. I wonder if this bdl_pos_adj is the real reason for the error. Here is my hardware information provided by alsa-info.sh website. Okay, i did some serious testing and even installed Windows and now i officially conclude that this is a hard-ware related issue with my Laptop speakers. Reason: The error occurs in my installed Debian Linux, an Ubuntu Live distribution and Windows XP No error-message appears in all of the OS. The sound just keeps running and i can't hear a thing. I tested different setups, including OSS, ALSA and the pulseaudio server on top If i use my new usb-headphones i can hear sound all the time without any sudden silences. So obviously, although hard to believe, my laptop speakers are not okay (never heard of similar cases). I'll award the bounty to anyone who can point me to good tutorials or the procedure how to exchange my T410 speakers (i still have warranty. The laptop was bought in Germany, but now i am in Denmark). Or to someone who can explain me the output from hda-analyzer (big log above).

    Read the article

  • One user sometimes gets an unknown certificate error opening Outlook

    - by Chris
    Let me clarify a little. This isn't an unknown certificate error it's an unknown certificate error in so much as I can't figure out where the certificate comes from. This happens on a Win 7 Enterprise machine connecting to Exchange 2010 with Outlook 2010. The error he gets is that the root is not trusted because it's a self-signed cert. Take a look at this screenshot because even if I had generated this myself I wouldn't have put "SomeOrganizationalUnit" or "SomeCity" or "SomeState", etc. (Red block covers our domain name.) I'm a little concerned this is a symptom of a security breach. Exchange 2010 has three certificates installed but none of them are this certificate. They all have different expiration dates (one is expired) and different meta-data. edit: There are two scenarios that I see the certificate warning and one of them I can reliably repeat. When the user leaves his computer on over night Outlook pops the Security Warning window. I don't know what time this happens. Using Outlook Anywhere if I connect to Exchange externally via a cellular USB modem the Security Warning window will appear every time I close and reopen Outlook. Whether I say Yes or No does not make a difference on whether or not I can connect to Exchange and send/receive email. In other words, I can always connect to Exchange. I've checked my two Exchange servers and my Cisco router for a certificate that matches this one and I can't find it. edit 2: Here is a screenshot of the Security Alert window. (I've been calling it Security Warning... My mistake.) edit 3: I stopped seeing this error several weeks ago but I can't tie it to any single event (because I just sort of realized that warning had stopped showing up) but I think I found the source of the certificate. Last week I found out that the certificate on our website DomainA.com was invalid. I knew that our web admin had installed a valid certificate so when I look into the problem I found out I was being presented with the invalid certificate that this posting is in regards to. The Exchange server's domain is mail.DomainA.com so I can only guess that Outlook was passing this invalid certificate through as it did some kind of check on DomainA.com. This issue is still a mystery because the certificate warning stopped appearing several weeks ago whereas the invalid certificate issue on the website was only fixed last week. It ended up being a problem with the website control panel. The valid certificate was installed but not being served for some reason and instead the self-signed cert was being served.

    Read the article

  • Partition/install issues

    - by jalal ahmad
    I am new to Ubuntu and tried to install 10.1 as dual boot option from a USB. At first I encountered the error when in partition dialogue of installation process that cannot find root directory. I did a search on Ubuntu forums and did this as in one of the posts. Make sure that the partition file system you wish to install Linux, Ubuntu or Backtrack on it is ext4, ext3 or ext2, and not FAT32 or NTFS. Then mount / on it: During the installation process press "change" on the partition you wish to use Make sure "do not use this partition" scroll is not chosen, scroll to ext4, ext3 or ext2 On the "mount" field write / Click ok, then next a message will appear saying something like "swap area was not defined, do you wish to continue or choose a swap area?", click "ok" and continue or click "go back" and choose another partition and click change, on the file system scroll choose "swap" and click "ok" and next All good but when I rebooted I could not find Windows vista as in dual boot option. Plus I could not see wireless networks and in the process of trying to find out what went wrong the soft switch somehow turned off and as I cannot boot in Windows I have no idea what to do. Again searching internet I found a post which said the dual boot problem can be overcome by installing gparted but when I tried I got the message Reading package lists... Done Building dependency tree Reading state information.. Done E: Couldn't find package gparted I thought I am going to copy my stuff from my hard disk and try to install Windows but I found out that I have two partitions which are different from what I had before installing Ubuntu. I now have filesystem partition1 119 GB ext4, swap partition 5 1.1 GB swap and extended partition 2 1.1 GB. And I cannot mount 119 GB where all my personal videos, photos are if still there. Now I cannot boot from Windows even. Need help on what to do? Best case scenario would be to be able to copy my stuff before I mess up the system further. Else a dual boot system and if not then how do I install vista again. I have Windows CD. Cheers guys and thanks in advance.

    Read the article

  • Spotlight Infinite Indexing issue (external data drive)

    - by Manca Weeks
    This is an external drive, formerly a boot drive which is now in use only to access music files (sibelius, audio, midi, live, logic etc.) without transferring the data into a new boot system, partly because of the issue I am about to describe, but mostly because the majority of the data is mainly there for archival purposes. The user is a composer and prominent musician and needs to be able to rehash the data at will. I have tried several things - here is a list: - make complete filesystem clone with antonio diaz's ddrescue - run Disk Warrior on copy, repair whatever errors occurred - wipe out all ACLs on entire drive - set all permissions to the same value - wide open 777 - remove any system data (applications, system files, including hidden files to the best of my knowledge) by selecting only non-system/app data and using Carbon Copy Cloner to put only the data of interest onto a newly formatted drive - transfer data to newly formatted drive folder by folder, resetting the spotlight index in between adding each to observe for issues (interesting here is that no issues occurred except for in Documents folder - when I transferred only the Documents folder to a newly formatted drive on its own - no trouble. It appears almost as thought it may not be the content but the quantity or specific combination of data that results in problems) - use DataRescue to transfer the data to yet another newly formatted drive to expose any missed hidden files Between each of the above steps I stopped Spotlight (search for anything beginning with md in Activity Monitor - All Processes and quitting it), deleted the .Spotlight-V100 directory from the affected drive. Restart Splotlight indexing by adding drive to Spotlight privacy list and removing it. In each case the same issue occurs - Spotlight begins indexing normally (or so it seems), then the index estimated time increases, usually to 4 hours remaining. This is where it gets stuck and continues to predict 4 hours remaining but never finishes. Sometimes I can't eject the drive and have to quit the md.. processes from Activity Monitor to be able to eject the drive without Force Eject. Once I disconnect the drive after the 4 hours remaining situation - if I reattach it, Spotlight forever estimates remaining time and never gets going again. So there it is. It is apparently not a filesystem issue, not a permissions issue and not tied to any particular piece of hardware or protocol (used USB and FW drives). I have tried this on several machines (3 to be precise) and in 10.5.8 and 10.6.5. Simply disabling Spotlight on this volume is not an option because the owner has no clue where things are as the data on the volume dates back to music projects and compositions from 2003 and before. He needs to be able to query for results. Anyone got any ideas? Thanks, M

    Read the article

  • Logitech Optical Mouse Frozen In Middle of Windows XP Pro Screen

    - by Code Sherpa
    Hi. I have a Logitech Optical Mouse/Keyboard. I have been using them just fine with the system drivers for almost a year now. I recently updated my Kaspersky software and rebooted. Now the mouse is frozen in the middle of my screen. I am not able to login to the Windows XP Pro box that has the frozen mouse (because i can't work the mouse) but am able to remote desktop to this computer. Things I know / have tried: When I boot on the problem computer, I am able to use the keyboard, but not the mouse. I have installed the latest version of Logitech's SetPoint (with the updated drivers) on the problem computer (via remote desktop) and that didn't seem to matter. I bought new batteries for the mouse and that didn't matter. I have tried the mouse/keyboard on another computer and the mouse works just fine there. My suspicion is that the Kaspersky install has overwritten a driver of some sort. Things I have not done (and would appreciate detailed steps if you feel this is the way to go): 1) Uninstalled all the mouse drivers on the machine and reboot. Then, reinstall. Note: When I get to the Device Manager I don't see an option for Human Interface Devices (where the mouse device is). Here are my options: Computer, Disk Drives, DVD/CD-Rom drives, Floppy controllers, IDE ATA/ATAPI, Imaging devices, Network Adapters, Other devices, Ports, Processors, Sound, video, and gaming, System devices, USB controllers. Also, I should point out that Video Controller is the only thing under Other devices and it has a yellow exclamation mark. The same is true for all the items under Universal Serial Bus controllers. I think this means I have to update my BIOS but, since my mouse was working just fine without doing that, I don't think that is my problem. So, how do I get to my Mouse Device? 2) Update my BIOS. Note: As pointed out above, I don't think this matters as my mouse was working just fine under my computer's current BIOS version. Thanks for your help.

    Read the article

  • Model M Keyboard inputs incorrect characters after logging in to Fedora

    - by mickburkejnr
    I recently bought a 24 year old IBM Model M keyboard. From what I gather, it'd been left on a shelf for the last 5 years, so you can imagine the amount of dust dirt and crap that was on it. Before cleaning it, I plugged it in to my laptop (running Fedora 17) using a PS/2 to USB adapter. What I found was, while it still works, the keys I press don't correspond to what is displayed on the screen. So for example, when I type S on the keyboard, I get ß display on the screen instead. At the time, I put this down to the adapter not working properly. Since then, I stripped the keys off the keyboard and cleaned the whole thing. It looks like it's just come out of a box! I then plugged it in to my computer (also running Fedora 17) via a standard PS/2 plug. The computer loaded up to the login screen, and I typed in my password. Pressed enter, and I logged straight in to my machine. At this point, I opened up a text editor and started typing some stuff. To my horror, the keystrokes I was entering weren't coming up as intended. What came up instead were characters that would map to the pressed key but only under a different keyboard language setting. I opened up a program to see what keyboard language had been selected, and the correct one for the keyboard was selected (which is UK in my case). I opened up a window that would show what characters mapped to what keys, and I pressed every single key on the keyboard, and every corresponding block representing each key lit up. I went back to the text editor to try again, but I was still getting these random characters. Whats more is that the backspace key would not work, although in the other utility it would flash when pressed. What I know is that at the login screen the keyboard must have entered the correct characters, otherwise I wouldn't have been able to log in. Further more, keys that don't respond while using a text editor as sending signals to the computer, as illustrated in that keyboard utility. The question is why random characters are displayed when they really shouldn't be? Would this be a hardware fault or a software issue?

    Read the article

  • How do you backup 40+ Centos5.5 servers?

    - by John Little
    We are embarrassed to ask this question. Apologies for our lack of UNIX expertise. We have inherited 40+ centos 5.5 servers, and don't know how to back them up. We need low level clone type images so that we could restore the servers from scratch if we had to replace the HDs etc. We have used the "dd" command, but we assume this only works if you want to back up one local disk to another, not 40 servers to one server with an external USB HD attached. All 40 servers have a pair of mirrored disks (dont know if its HW or SW raid). Most only have 100MB used. SErvers are running apache, zend, tomcat, mysql etc. Ideally we dont want to have to shut them down to backup (but could). We assume that standard unix commands like tar, cpio, rsync, scp etc. are of no use as they only copy files, not partitions, all attributes, groups etc. i.e. do not produce a result which can simply be re-imaged to a new HD to get the serer back from dead. We have a large SAN, a spare windows box and spare unix boxes, but these are only visible to one layer in the network. We have an unused Dell DL2000 monster tape unit, but no sw or documentation for it. WE have a copy of symantec backup exec, but we have no budget for unix client licenses. (The company has negative amounts of money). We need to be able to initiate the backup remotely, as we can only access the servers in person in an emergency (i.e. to restore) Googling returns some applications to do this, e.g. clonezilla - looks difficult to install and invasive. Mondo, only seems to support backup if you are local to the machine. Amanda might be an option, but looks like days/weeks of work to learn and setup? Is there anything built into Centos, or do we have to go the route of installing, learning and configuring a set of backup softwares? Any ideas? This must be a pretty standard problem which goggling doesnt give an obvious answer.

    Read the article

  • Repair BAD Sectors or Buy a new HDD?

    - by Nehal J. Wani
    I have a Seagate internal hard disk drive. I recently opened up my laptop [Dell Inspiron N5010] [Warranty has expired], cleaned it and it worked normally after waking up from hibernation. However, when I restarted it, it stuck on windows loading screen, then tried to boot from Dell recovery partition but failed. It gave the error: Windows has encounter a problem communicating with a device connected to your computer. This error can be caused by unplugging a removable storage device such as an external USB drive while the device is in use, or by faulty hardware such as a hard drive or CD-ROM drive that is failing. Make sure any removable storage is properly connected and then restart your computer If you continue to receive this error message, contact the hardware manufacturer. Status: 0xc00000e9 Info: An unexpected I/O error has occurred. While cleaning, I had mistakenly touched the round silvery thing at the bottom of the HDD. I don't know whether this has caused the problem or not. Since I have Fedora also installed in the same HDD, I can boot from it but it shows weird read errors when I ask it to mount Windows partitions. The disk utility also says that the Hard Disk has many bad sectors and needs to be replaced. I downloaded Seatools from Seagate website and used it. In the long test, I gave it permission to repair the first 100 errors which it did successfully. Now I am confused at what I should do. Internal Hard Disk Costs: a. Internal HDD 500GB Costs: Rs3518 b.1 External HDD 500GB Costs: Rs3472 b.2 External HDD 1TB Costs: Rs5500 c. Internal to External Converter Costs: Rs650 I have the following options: (i) Buy an External HDD, backup my data. Try to repair bad sectors of HDD. Then two cases arise: (a) My Internal HDD gets repaired [almost] (b) My internal HDD doesn't get repaired. Then I need to buy another internal HDD and replace the damaged one. OR break the seal of the external one and put it inside my laptop as internal. Breaking the case involves risks. (ii) Buy a Internal HDD and an Internal to External Converter Case [Not very reliable], backup my data. Try to repair bad sectors of HDD. Then two cases arise: (a) My Internal HDD gets repaired [almost] (b) My internal HDD doesn't get repaired. Then I need to just put in the new internal HDD I just bought. Experts, please guide me as to what will be the most VFM option? Also, if a HDD is failing, is it that I shouldn't read from it too otherwise there is a chance of other sectors failing? What I mean is, is it wrong to read from the HDD without taking backup first?

    Read the article

  • If Nvidia Shield can stream a game via wifi, why can I not do the same via ethernet to any other PC?

    - by Enigma
    I think it absurd that a wireless game streaming solution is the *first to hit the market when a 1000mbps+ Ethernet connection would accomplish the same feat with roughly 6x the available bandwidth. I can only assume that there must be some reason behind this or a limitation preventing this, but what? 150mbps wifi is in no way superior to a 1000mbps LAN connection aside from well wireless mobility. Not only that but I have a secondary laptop and desktop which should by hardware comparison completely outperform anything the Tegra in the Nvidia Shield can do. Is this all just a marketing scheme to force people to buy the shield for the streaming benefit? Chief among these is that NVIDIA’s Shield handheld game console will be getting a microconsole-like mode, dubbed “Shield Console Mode”, that will allow the handheld to be converted into a more traditional TV-connected console. In console mode Shield can be controlled with a Bluetooth controller, and in accordance with the higher resolution of TVs will accept 1080p game streaming from a suitably equipped PC, versus 720p in handheld mode. With that said 1080p streaming will require additional bandwidth, and while 720p can be done over WiFi NVIDIA will be requiring a hardline GigE connection for 1080p streaming (note that Shield doesn’t have Ethernet, so this is presumably being done over USB). Streaming aside, in console mode Shield will also support its traditional local gaming/application functionality. - http://www.anandtech.com/show/7435/nvidia-consolidates-game-streaming-tech-under-gamestream-brand-announces-shield-console-mode ^ This is not acceptable for me for a number of reasons not to mention the ridiculousness of having a little screen+controller unit sitting there while using a secondary controller and screen instead. That kind of redundant absurdity exemplifies how wrong of a solution that is. They need a second product for this solution without the screen or controller for it to make sense... at which point your just buying a little computer that does what most other larger computers do better. All that is required, by my understanding, is the ability to decode H.264 video compression and transmit control/feedback so by any logical comparison, one (Nvidia especially) should have no difficulty in creating an application for PC's (win32/64 environment) that does the exact same thing their android app does. I have 2 video cards capable of streaming (encoding) H.264 so by right they must be capable of decoding it I would think. I haven't found anything stating plans to allow non-shield owners to do this. Can a third party create this software or does it hinge on some limitation that only Nvidia can overcome? (*) - perhaps this isn't the first but afaik it is the first complete package.

    Read the article

  • Mouse Error Code 24. Windows 7

    - by Cj.
    I've had the same mouse for a while, and it's been working fine until one day, it started giving me a message about a device not working properly. I tried updating the drivers, and re-installing, I even deleted old drivers in case my computer should be a little confused. It never made a difference, and my mouse seemed to be working just fine despite getting the permanent error in my device manager, I looked it up several times online, but I never found anything I could actually use, when I go to official websites, I always get the same response "plug in so so into a different place - drivers - install silverlight before you can watch this tutorial, try it on a different machine". so I gave up on that. But now is where I have a real problem, lately, my little strange error evolved into a fullblown Error 24, and my mouse is starting to turn on and off randomely, especially when it is being used, but I do hear it go "badum..dadum" when I'm off doing something else. when I looked up error code 24, I really didn't find much other than it meaning: Code 24 This device is not present, is not working properly, or does not have all its drivers installed. (Code 24) Cause The device is installed incorrectly. The problem could be a hardware failure, or a new driver might be needed. Devices stay in this state if they have been prepared for removal. After you remove the device, this error disappears. But, I have tried uninstalling the device entirely several times, and it'll go right back to its previous state with error 24, and turning on and off randomely. what do I do? I cannot afford taking it to a repair place, I can't really afford a new mouse either, I refuse to buy cheap ones as I am a gamer, in need of more than 3 buttons, and a good grip is important. Could there possibly be some confusion in the registry? I do remember having gotten some early problems after I converted my vista to windows7. But I hardly dare going in there unless I'm 100% certain of what I'm going for, and I can honestly say I am at a loss here. Edit: it is a USB mouse we're talking about here. MX™518 Optical Gaming Mouse (logitech) Edit2: I am seeing no rupture, so it must be on the inside of my mouse, or inside the rubber, protecting the cable, that would be really inconvenient to search for

    Read the article

  • Resetting root password on Fedora Core 3 - serial cable access only

    - by Sensible Eddie
    A little background: We have an old rackmount server running a customised version of Fedora, manufactured by a company called Navaho. The server is a TeamCAT, running some proprietary rubbish called Freedom2. We have to keep it going - the alternative is extraordinarily expensive, and the business is not likely to be running much longer to justify changing things. Through one means or another, it has fallen upon me to try and resolve our lack of root access. The previous admin has fallen under the proverbial bus, and nobody has any clue. We have no access to the root account for this server. ssh is running on the server, and there is one account admin that we can login with, however it has no permission to do anything (ironic...) The only other way into the server is with a null-modem serial cable. This works... up to a point. I can see the BIOS, I can see the post BIOS screen, and then I see "Starting grub", followed by another screen with about four lines of Linux information, but then it stops at that point. The server continues booting, and all services come online after around two minutes, but the serial terminal displays no more information. I understand it is possible to put Linux into "single user mode" to reset a root password, but I have no idea how to do this beyond trying to interrupt it at the grub stage listed above. When I have tried it just froze. It was almost like grub had appeared (since the server did not continue booting) but I couldn't see it on the serial terminal. Which made me think maybe the grub screen has some different serial settings? I don't know... it's the first time I've ever used serial for access! A friend of mine suggested trying to use a Fedora boot CD. We could boot from USB, so something along this approach is possible but again we still can only see what's going on with the serial terminal, so it might not be achievable. Does anyone have any suggestions for things I can try? I appreciate this is a bit of a long shot, but any assistance would be invaluable. *UPDATE 1 - 28/8/12 * - we will be making some attempts on this today and will post further details later!

    Read the article

  • Issue using a "used" SSD as a Windows 8.1 Boot Drive

    - by EpiGrad
    So, I'm something of a Mac person, but decided to take a stab at this whole "build yourself a PC" thing - right now, the thing is assembled, posts just fine, and can get to the BIOS. The problem is the drive I want to use - I intended to use a 80 GB Corsair SSD I've had sitting around as the boot drive, and a new Samsung SSD for games and the like. So I boot using a Windows 8.1 install USB stick, and if the Samsung drive is plugged in, it happily offers to install Windows on it. The Corsair drive though, it's flipped out - I reformatted it as a blank NTFS drive (it was HFS for Mac purposes) and the BIOS can't see it, nor can the Windows installer. What's wrong, and how do I fix it? The tools at my disposal are: The current ASUS BIOS that came with my motherboard (a Z87I-Deluxe), a Mac running the latest OS X which can also boot to Windows 7 if needed via either Parallels or Bootcamp. Update 1: Update: Based on a friend's suggestion to switch SATA ports, Windows 8.1's installer can now see the drive as Drive 0, Partition 1, a 83.8 GB "Primary" partition. But when I click it and hit "Next", I get the following error: "We couldn't create a new partition or locate an existing one. For more information, see the Setup log files" - not that it gives any clue how to access those. Update 2: Following a trail of Google suggestions, I ended up going into advanced tools and just reformatting the drive as follows: Start DISKPART. Type LIST DISK and identify your SSD disk number (from 0 to n disks). Type SELECT DISK <n> where <n> is your SSD disk number. Type CLEAN Type CREATE PARTITION PRIMARY Type ACTIVE Type FORMAT FS=NTFS QUICK Type ASSIGN Type EXIT twice (one to get out of DiskPart, the other to exit the command line tool) Per these instructions. This goes well enough, but now I can select the disk for installation, and I get a new error: "Windows 8 cannot be installed to this disk. The selected disk has an MBR partition table. On EFI systems, Windows can only be installed to GP disks." So, Googling that, I do the following: select disk 0 clean convert gpt exit ...and we might have fixed it. Windows is at least trying to install now.

    Read the article

  • Linux software RAID6: 3 drives offline - how to force online?

    - by Ole Tange
    This is similar to 3 drives fell out of Raid6 mdadm - rebuilding? except that it is not due to a failing cable. Instead the 3rd drive fell offline during rebuild of another drive. The drive failed with: kernel: end_request: I/O error, dev sdc, sector 293732432 kernel: md/raid:md0: read error not correctable (sector 293734224 on sdc). After rebooting both these sectors and the sectors around them are fine. This leads me to believe the error is intermittent and thus the device simply took too long to error correct the sector and remap it. I expect that no data was written to the RAID after it failed. Therefore I hope that if I can kick the last failing device online that the RAID is fine and that the xfs_filesystem is OK, maybe with a few missing recent files. Taking a backup of the disks in the RAID takes 24 hours, so I would prefer that the solution works the first time. I have therefore set up a test scenario: export PRE=3 parallel dd if=/dev/zero of=/tmp/raid${PRE}{} bs=1k count=1000k ::: 1 2 3 4 5 parallel mknod /dev/loop${PRE}{} b 7 ${PRE}{} \; losetup /dev/loop${PRE}{} /tmp/raid${PRE}{} ::: 1 2 3 4 5 mdadm --create /dev/md$PRE -c 4096 --level=6 --raid-devices=5 /dev/loop${PRE}[12345] cat /proc/mdstat mkfs.xfs -f /dev/md$PRE mkdir -p /mnt/disk2 umount -l /mnt/disk2 mount /dev/md$PRE /mnt/disk2 seq 1000 | parallel -j1 mkdir -p /mnt/disk2/{}\;cp /bin/* /mnt/disk2/{}\;sleep 0.5 & mdadm --fail /dev/md$PRE /dev/loop${PRE}3 /dev/loop${PRE}4 cat /proc/mdstat # Assume reboot so no process is using the dir kill %1; sync & kill %1; sync & # Force fail one too many mdadm --fail /dev/md$PRE /dev/loop${PRE}1 parallel --tag -k mdadm -E ::: /dev/loop${PRE}? | grep Upda # loop 2,5 are newest. loop1 almost newest => force add loop1 Next step is to add loop1 back - and this is where I am stuck. After that do a xfs-consistency check. When that works, check that the solution also works on real devices (such a 4 USB sticks).

    Read the article

  • How to reliably map vSphere disks <-> Linux devices

    - by brianmcgee
    Task at hand After a virtual disk has been added to a Linux VM on vSphere 5, we need to identify the disks in order to automate the LVM storage provision. The virtual disks may reside on different datastores (e.g. sas or flash) and although they may be of the same size, their speed may vary. So I need a method to map the vSphere disks to Linux devices. Ideas Through the vSphere API, I am able to get the device info: Data Object Type: VirtualDiskFlatVer2BackingInfo Parent Managed Object ID: vm-230 Property Path: config.hardware.device[2000].backing Properties Name Type Value ChangeId string Unset contentId string "d58ec8c12486ea55c6f6d913642e1801" datastore ManagedObjectReference:Datastore datastore-216 (W5-CFAS012-Hybrid-CL20-004) deltaDiskFormat string "redoLogFormat" deltaGrainSize int Unset digestEnabled boolean false diskMode string "persistent" dynamicProperty DynamicProperty[] Unset dynamicType string Unset eagerlyScrub boolean Unset fileName string "[W5-CFAS012-Hybrid-CL20-004] l****9-000001.vmdk" parent VirtualDiskFlatVer2BackingInfo parent split boolean false thinProvisioned boolean false uuid string "6000C295-ab45-704e-9497-b25d2ba8dc00" writeThrough boolean false And on Linux I may read the uuid strings: [root@lx***** ~]# lsscsi -t [1:0:0:0] cd/dvd ata: /dev/sr0 [2:0:0:0] disk sas:0x5000c295ab45704e /dev/sda [3:0:0:0] disk sas:0x5000c2932dfa693f /dev/sdb [3:0:1:0] disk sas:0x5000c29dcd64314a /dev/sdc As you can see, the uuid string of disk /dev/sda looks somehow familiar to the string that is visible in the VMware API. Only the first hex digit is different (5 vs. 6) and it is only present to the third hyphen. So this looks promising... Alternative idea Select disks by controller. But is it reliable that the ascending SCSI Id also matches the next vSphere virtual disk? What happens if I add another DVD-ROM drive / USB Thumb drive? This will probably introduce new SCSI devices in between. Thats the cause why I think I will discard this idea. Questions Does someone know an easier method to map vSphere disks and Linux devices? Can someone explain the differences in the uuid strings? (I think this has something to do with SAS adressing initiator and target... WWN like...) May I reliably map devices by using those uuid strings? How about SCSI virtual disks? There is no uuid visible then... This task seems to be so obvious. Why doesn't Vmware think about this and simply add a way to query the disk mapping via Vmware Tools?

    Read the article

  • How to install RAID drivers on already installed Windows 7?

    - by happysencha
    64-bit Windows 7 Ultimate 6GB RAM Intel i7 920 Intel X25-M SSD 80GB 2,5" Club 3D Radeon HD5750 GA-EX58-UD4P Motherboard I've been running fine with Windows 7 installed on the SSD. I wanted to create an mirrored Raid-1 setup for backups using two hard disks, so I ordered two Samsung HD203WI. This motherboard supports two different RAID controllers, the Intel's ICH10R and Gigabyte's SATA2 SATA controller. There are 6 SATA ports behind the ICH10R and 2 SATA ports for the Gigabyte controller. I googled around and seemed that the ICH10R is a better choice and since then I've been trying to make it work. When I activate the [RAID] mode from BIOS, the Windows 7 gives BSOD exactly as described by this guy: "Windows 7 will start to boot, it gets to the screen where there are 4 colors coming together and it blue screens and restarts no matter what I do." First thing I did: turned off the RAID and booted to Windows and tried to install the SATA RAID drivers from Gigabyte. I launch the driver installation program and it gives "This computer does not meet the minimum requirements for installing the software" error. I then tried Intel's Rapid Storage Technology drivers (which apparently is the same as the one offered at Gigabyte's site), but it resulted in exactly the same error. I then detached the new Samsung hard disks from the SATA ports, but left the [RAID] enabled in BIOS. To my surprise, it still BSOD'd, so at this point I knew it is an OS/driver issue. Also, I tried with the Gigabyte's RAID enabled (while the ICH10R RAID disabled) and it booted just fine. So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed." So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks. I mean why would I need to re-install operating system to add RAID setup?

    Read the article

< Previous Page | 251 252 253 254 255 256 257 258 259 260 261 262  | Next Page >