Search Results

Search found 21640 results on 866 pages for 'local storage'.

Page 258/866 | < Previous Page | 254 255 256 257 258 259 260 261 262 263 264 265  | Next Page >

  • Nginx + Nagios : 502 Bad gateway

    - by MrROY
    I have a fully new install nagios, but I can't access to it. Here's my Nginx config: server{ listen 80; server_name 61.148.45.10; # blahblah # Nagios Monitoring location /nagios3/ { proxy_pass http://127.0.0.1:80; } } Nagios is installed step by step(From this Linode guide): sudo apt-get install -y nagios3 Then I try to visit http://ip-address/nagios3/, but it shows 502 bad gateway. How do I deal with this ? This is my /var/log/syslog: Oct 25 14:18:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;1;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:19:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;1;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:19:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;2;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:20:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;2;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:20:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;3;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;3;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:21:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;HARD;4;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:17 my-server nagios3: SERVICE NOTIFICATION: root;localhost;Disk Space;WARNING;notify-service-by-email;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:17 my-server postfix/pickup[24474]: 4F89F394034C: uid=109 from=<nagios> Oct 25 14:21:17 my-server postfix/cleanup[27756]: 4F89F394034C: message-id=<20131025062117.4F89F394034C@my-server> Oct 25 14:21:17 my-server postfix/qmgr[24475]: 4F89F394034C: from=<nagios@[email protected]>, size=594, nrcpt=1 (queue active) Oct 25 14:21:17 my-server postfix/local[27758]: 4F89F394034C: to=<root@localhost>, relay=local, delay=0.15, delays=0.11/0/0/0.04, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 14:21:17 my-server postfix/qmgr[24475]: 4F89F394034C: removed Oct 25 14:22:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;HARD;4;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:22:07 my-server nagios3: SERVICE NOTIFICATION: root;localhost;HTTP;WARNING;notify-service-by-email;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:22:07 my-server postfix/pickup[24474]: 219CA3940381: uid=109 from=<nagios> Oct 25 14:22:07 my-server postfix/cleanup[27756]: 219CA3940381: message-id=<20131025062207.219CA3940381@my-server> Oct 25 14:22:07 my-server postfix/qmgr[24475]: 219CA3940381: from=<nagios@[email protected]>, size=605, nrcpt=1 (queue active) Oct 25 14:22:07 my-server postfix/local[27758]: 219CA3940381: to=<root@localhost>, relay=local, delay=0.12, delays=0.07/0/0/0.05, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 14:22:07 my-server postfix/qmgr[24475]: 219CA3940381: removed Oct 25 14:39:01 my-server CRON[28242]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) And there're lot of 127.0.0.1 visit in nginx log, but I actually visit from a external ip: 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36" 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36" 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36"

    Read the article

  • PHP crashing (seg-fault) under mod_fcgi, apache

    - by Andras Gyomrey
    I've been programming a site using: Zend Framework 1.11.5 (complete MVC) PHP 5.3.6 Apache 2.2.19 CentOS 5.6 i686 virtuozzo on vps cPanel WHM 11.30.1 (build 4) Mysql 5.1.56-log Mysqli API 5.1.56 The issue started here http://stackoverflow.com/questions/6769515/php-programming-seg-fault. In brief, php is giving me random segmentation-faults. [Wed Jul 20 17:45:34 2011] [error] mod_fcgid: process /usr/local/cpanel/cgi-sys/php5(11562) exit(communication error), get unexpected signal 11 [Wed Jul 20 17:45:34 2011] [warn] [client 190.78.208.30] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Wed Jul 20 17:45:34 2011] [error] [client 190.78.208.30] Premature end of script headers: index.php About extensions. When i compile php with "--enable-debug" flag, i have to disable this line: zend_extension="/usr/local/IonCube/ioncube_loader_lin_5.3.so" Otherwise, the server doesn't accept requests and i get a "The connection with the server was reset". It is possible that i have to disable eaccelerator too because of the same reason. I still don't get why apache gets running it some times and some others not: extension="eaccelerator.so" Anyway, after i get httpd running, seg-faults can occurr randomly. If i don't compile php with "--enable-debug" flag, i can get DETERMINISTICALLY a php crash: <?php class Admin_DbController extends Controller_BaseController { public function updateSqlDefinitionsAction() { $db = Zend_Registry::get('db'); $row = $db->fetchRow("SHOW CREATE TABLE 222AFI"); } } ?> BUT if i compile php with "--enable-debug" flag, it's really hard to get this error. I must add some complexity to make it crash. I have to be doing many paralell requests for a few seconds to get a crash: <?php class Admin_DbController extends Controller_BaseController { public function updateSqlDefinitionsAction() { $db = Zend_Registry::get('db'); $tableList = $db->listTables(); foreach ($tableList as $tableName){ $row = $db->fetchRow("SHOW CREATE TABLE " . $db->quoteIdentifier($tableName)); file_put_contents( DB_DEFINITIONS_PATH . '/' . $tableName . '.sql', $row['Create Table'] . ';' ); } } } ?> Please notice this is the same script, but creating DDL for all tables in database rather than for one. It seems that if php is heavy loaded (with extensions and me doing many paralell requests) it's when i get php to crash. About starting httpd with "-X": i've tried. The thing is, it is already hard to make php crash with --enable-debug. With "-X" option (which only enables one child process) i can't do parallel requests. So i haven't been able to create to proper debug backtrace: https://bugs.php.net/bugs-generating-backtrace.php My concrete question is, what do i do to get a coredump? root@GWT4 [~]# httpd -V Server version: Apache/2.2.19 (Unix) Server built: Jul 20 2011 19:18:58 Cpanel::Easy::Apache v3.4.2 rev9999 Server's Module Magic Number: 20051115:28 Server loaded: APR 1.4.5, APR-Util 1.3.12 Compiled using: APR 1.4.5, APR-Util 1.3.12 Architecture: 32-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/usr/local/apache" -D SUEXEC_BIN="/usr/local/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf"

    Read the article

  • Windows 7 Samba issue

    - by abduls85
    We have a strange samba issue affecting only one user. Our samba setup is as follow : Red Hat Enterprise Linux Server release 5.4 (Tikanga) - Samba Server Samba version 3.0.33-3.14.el5 - Samba version Domain Controller WIN2008R2 Standard - Windows DC Windows 7 64 bit - Client PCs User mentioned that he faced this problem after he force shutdown his PC few weeks ago. By right, for all users when we access \\sambaservername in windows it will show all the shares in the samba server but for this user once he startup his PC he will not be able to access \\sambaservername, Error message Windows cannot access \\sambaservername Current workaround to solve the problem : Try to access one share in \\sambaservername for instance \\sambaservername\sharedfolder1. But even when doing so, it will first prompt an error in the beginning, error message is as follows Logon failure: unknown user name or bad password. user need to enter the credentials again and he can access the share. Thereafter, he will be able to access \\sambaservername without any issues. But once he reboots his computer the problem will persists. Troubleshooting done so far: Ensure the following settings: Go to: Control Panel → Administrative Tools → Local Security Policy Select: Local Policies → Security Options "Network security: LAN Manager authentication level" → Send LM & NTLM responses "Minimum session security for NTLM SSP" → uncheck: Require 128-bit encryption Advise user to reset his password and try again but problem still persists Tried my account on users' PC, there is no issues. Tried user account on serveral other Windows 7 PC including mine but problem still persists. Windows XP does not have this problem. Ensure that there is no stored crendentials on the windows 7 PC. Checked the credentials manager in Control Panel as well as typing this command rundll32.exe keymgr.dll, KRShowKeyMgr Restart winbindd daemon on samba server but to no avail. I suspect this is due to some caching issue but not sure where is the issue. Whenever the user has error accessing \\sambaservername, the following errors will be logged in the samba server : [2012/10/10 17:10:26, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! But after workaround, there will be no more errors. I suspect after reading the article listed below some amendments need to be made to the \var\samba\cache directory : http://www.linuxquestions.org/questions/linux-server-73/getent-passwd-dont-show-ad-groups-and-users-745829/ http://www.samba.org/samba/docs/man/Samba-HOWTO-Collection/tdb.html http://lists.samba.org/archive/samba/2010-May/155521.html http://lists.samba.org/archive/samba/2011-March/161912.html http://lzeit.blogspot.sg/2009/10/samba-shares-inaccessible-after-power.html There are several users using the samba server and i would like to solve this problem without any impacts. I saw the following article : http://www.samba.org/samba/docs/man/manpages-3/smb.conf.5.html#WINBINDCACHETIME "winbind offline logon (G) This parameter is designed to control whether Winbind should allow to login with the pam_winbind module using Cached Credentials. If enabled, winbindd will store user credentials from successful logins encrypted in a local cache. Default: winbind offline logon = false Example: winbind offline logon = true " Any idea on how to delete the entry for one user in the local cache ?

    Read the article

  • Running two wsgi applications on the same server gdal org exception with apache2/modwsgi

    - by monkut
    I'm trying to run two wsgi applications, one django and the other tilestache using the same server. The tilestache server accesses the db via django to query the db. In the process of serving tiles it performs a transform on the incoming bbox, and in this process hit's the following error. The transform works without error for the specific bbox polygon when run manually from the python shell: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/TileStache/__init__.py", line 325, in __call__ mimetype, content = requestHandler(self.config, environ['PATH_INFO'], environ['QUERY_STRING']) File "/usr/lib/python2.7/dist-packages/TileStache/__init__.py", line 231, in requestHandler mimetype, content = getTile(layer, coord, extension) File "/usr/lib/python2.7/dist-packages/TileStache/__init__.py", line 84, in getTile tile = layer.render(coord, format) File "/usr/lib/python2.7/dist-packages/TileStache/Core.py", line 295, in render tile = provider.renderArea(width, height, srs, xmin, ymin, xmax, ymax, coord.zoom) File "/var/www/tileserver/providers.py", line 59, in renderArea bbox.transform(METERS_SRID) File "/usr/local/lib/python2.7/dist-packages/django/contrib/gis/geos/geometry.py", line 520, in transform g = gdal.OGRGeometry(self.wkb, srid) File "/usr/local/lib/python2.7/dist-packages/django/contrib/gis/gdal/geometries.py", line 131, in __init__ self.__class__ = GEO_CLASSES[self.geom_type.num] File "/usr/local/lib/python2.7/dist-packages/django/contrib/gis/gdal/geometries.py", line 245, in geom_type return OGRGeomType(capi.get_geom_type(self.ptr)) File "/usr/local/lib/python2.7/dist-packages/django/contrib/gis/gdal/geomtype.py", line 43, in __init__ raise OGRException('Invalid OGR Integer Type: %d' % type_input) OGRException: Invalid OGR Integer Type: 1987180391 I think I've hit the non thread safe issue with GDAL, metioned on the django site. Is there a way I could configure this so that it would work? Apache Version: Apache/2.2.22 (Ubuntu) mod_wsgi/3.3 Python/2.7.3 configured Apache apache2/sites-available/default: <VirtualHost *:80> ServerAdmin ironman@localhost DocumentRoot /var/www/bin LogLevel warn WSGIDaemonProcess lbs processes=2 maximum-requests=500 threads=1 WSGIProcessGroup lbs WSGIScriptAlias / /var/www/bin/apache/django.wsgi Alias /static /var/www/lbs/static/ </VirtualHost> <VirtualHost *:8080> ServerAdmin ironman@localhost DocumentRoot /var/www/bin LogLevel warn WSGIDaemonProcess tilestache processes=1 maximum-requests=500 threads=1 WSGIProcessGroup tilestache WSGIScriptAlias / /var/www/bin/tileserver/tilestache.wsgi </VirtualHost> Django Version: 1.4 httpd.conf: Listen 8080 NameVirtualHost *:8080 UPDATE I've added the a test.wsgi script to determine if the GLOBAL interpreter setting is correct, as mentioned by graham and described here: http://code.google.com/p/modwsgi/wiki/CheckingYourInstallation#Sub_Interpreter_Being_Used It seems to show the expected result: [Tue Aug 14 10:32:01 2012] [notice] Apache/2.2.22 (Ubuntu) mod_wsgi/3.3 Python/2.7.3 configured -- resuming normal operations [Tue Aug 14 10:32:01 2012] [info] mod_wsgi (pid=29891): Attach interpreter ''. I've worked around the issue for now by changing the srs used in the db so that the transform is unnecessary in tilestache app. I don't understand why the transform() method, when called in the django app works, but then in the tilestache app fails. tilestache.wsgi #!/usr/bin/python import os import time import sys import TileStache current_dir = os.path.abspath(os.path.dirname(__file__)) project_dir = os.path.realpath(os.path.join(current_dir, "..", "..")) sys.path.append(project_dir) sys.path.append(current_dir) os.environ['DJANGO_SETTINGS_MODULE'] = 'bin.settings' sys.stdout = sys.stderr # wait for the apache django lbs server to start up, # --> in order to retrieve the tilestache cfg time.sleep(2) tilestache_config_url = "http://127.0.0.1/tilestache/config/" application = TileStache.WSGITileServer(tilestache_config_url) UPDATE 2 So it turned out I did need to use a projection other than the google (900913) one in the db. So my previous workaround failed. While I'd like to fix this issue, I decided to work around the issue this type by making a django view that performs the transform needed. So now tilestache requests the data through the django app and not internally.

    Read the article

  • Linux pptp client stops working after several hours

    - by Aron Rotteveel
    Here's the situation: Setup: 1 Windows Server 2008 machine acting as a Domain Controller and RRAS server 1 CentOS machine in a datacentre located elsewhere PPTP client running on CentOS machine, connected to the DC via When I connect to the DC, everything is working fine. I have set up a static IP for the dialup connection in my RRAS server so that the CentOS machine is automatically assigned the IP 192.168.1.240. Inside the VPN, it is not possible to access this machine on the local IP-address. Perfect. However, after several hours, it simply seems to stop working (IE: I cannot ping to or from this machine on the local network). The strange thing is, however: The DC shows the VPN client as still being connected The CentOS machine shows the network interface as being up There are no entries in my /var/log/messages that indicate a problem Output from ifconfig: ppp0 Link encap:Point-to-Point Protocol inet addr:192.168.1.240 P-t-P:192.168.1.160 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1396 Metric:1 RX packets:43 errors:0 dropped:0 overruns:0 frame:0 TX packets:58 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:4511 (4.4 KiB) TX bytes:15071 (14.7 KiB) Output from route -n: 192.168.1.160 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 ppp0 I have the following in my ip-up.local: route add -net 192.168.1.0 netmask 255.255.255.0 dev ppp0 The situation can be easily fixed by issueing a killall pppd and re-connecting. However, I obviously do not want to do this every X-hours or so. I have tried running pppd with both the debug as the kdebug flag but cannot find the cause of this problem. Currently, my ppp0 network interface seems to be running and the last log lines mentioning it are: Feb 19 14:10:40 graviton pppd[10934]: local IP address 192.168.1.240 Feb 19 14:10:40 graviton pppd[10934]: remote IP address 192.168.1.160 Feb 19 14:10:40 graviton pppd[10934]: Script /etc/ppp/ip-up started (pid 10952) Feb 19 14:10:40 graviton pppd[10934]: Script /etc/ppp/ip-up finished (pid 10952), status = 0x0 Feb 19 14:11:27 graviton pptp[10935]: anon log[decaps_gre:pptp_gre.c:414]: buffering packet 190 (expecting 189, lost or reordered) Feb 19 14:11:37 graviton pptp[10942]: anon log[logecho:pptp_ctrl.c:677]: Echo Request received. Feb 19 14:11:37 graviton pptp[10942]: anon log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 6 'Echo-Reply' Feb 19 14:12:37 graviton pptp[10942]: anon log[logecho:pptp_ctrl.c:677]: Echo Request received. Feb 19 14:12:37 graviton pptp[10942]: anon log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 6 'Echo-Reply' Feb 19 14:12:37 graviton pptp[10942]: anon log[logecho:pptp_ctrl.c:677]: Echo Reply received. Feb 19 14:13:37 graviton pptp[10942]: anon log[logecho:pptp_ctrl.c:677]: Echo Reply received. Feb 19 14:14:37 graviton pptp[10942]: anon log[logecho:pptp_ctrl.c:677]: Echo Reply received. Feb 19 14:15:37 graviton pptp[10942]: anon log[logecho:pptp_ctrl.c:677]: Echo Reply received. Feb 19 14:16:37 graviton pptp[10942]: anon log[logecho:pptp_ctrl.c:677]: Echo Reply received. Feb 19 14:19:37 graviton pptp[10942]: anon log[logecho:pptp_ctrl.c:677]: Echo Reply received. Feb 19 14:19:37 graviton pptp[10942]: anon log[logecho:pptp_ctrl.c:679]: no more Echo Reply/Request packets will be reported. I have enabled the persist option. The network interface is still running, but it is still impossible to send data through the VPN. Any help is appreciated.

    Read the article

  • Sharepoint AD imported users are becomming sporadically corrupted, causing us to have to create a new account

    - by TrevJen
    Sharepoint 2007 MOSS with AD imported users. All servers are 2008. ***UPDATE More details in testing. This Sharepoint is in an AD Child domain (clients.mycompany.local), which is sub to the root of the AD tree (mycompany.local). The user is in the parent tree (as are half of the other functional users. I have elevated the user rights to Domain. In looking at the logs, it seems that the Sharepoint server is trying to authenticate them by querying the DC for the clients domain (which is the way it normally works and still works for all existing identically configured users). I think if I could force it to authenticate up to the top domain DC then it would be ok?? I have around 50 users, over the past 2 months, I have had a handful of the users suddenly unable to login to Sharepoint. When they login, they either get a blank screen or they are repropmted. These users are using accounts that have been used for many months, sometimes the problem originates with a password change. In all cases, the users account works on every other Active Directory authenticated resource (domain, exchange, LDAP). In the most recent case, last night I was forced deleted a user ("John smith") because of corruption. The orifinal account name was jsmith. I deleted him from active directory, then deleted him from the profile list in Sharepoint Shared Services. I could not find a way to delete him from the Sharepoint user list, but I reran the import after recreating his account (renamed it too just to be sure to "smithj"). At first, this did not wor, the user could still access all other resources but Sharepoint. then, some 30 minutes later it inexplicably started working. This morning, the user changed passwords, which immediatly broke the login on Sharepoint again. Logs by request from matt b Office SharePoint Server Date: 4/13/2010 2:00:00 PM Event ID: 7888 Task Category: Office Server General Level: Error Keywords: Classic User: N/A Computer: nb-portal-01.clients.netboundary.local Description: A runtime exception was detected. Details follow. Message: Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED)) – TrevJen 19 hours ago Techinal Details: System.UnauthorizedAccessException: Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED)) at Microsoft.SharePoint.SPGlobal.HandleUnauthorizedAccessException(UnauthorizedAccessException ex) at Microsoft.SharePoint.Library.SPRequest.UpdateField(String bstrUrl, String bstrListName, String bstrXML) at Microsoft.SharePoint.SPField.UpdateCore(Boolean bToggleSealed) – TrevJen 19 hours ago at Microsoft.SharePoint.SPField.Update() at Microsoft.Office.Server.UserProfiles.SiteSynchronizer.UserSynchronizer.PushSchemaToList(Boolean& bAddedColumn) at Microsoft.Office.Server.UserProfiles.SiteSynchronizer.UserSynchronizer.SynchFull() at Microsoft.Office.Server.UserProfiles.SiteSynchronizer.Synch() at Microsoft.Office.Server.Diagnostics.FirstChanceHandler.ExceptionFilter(Boolean fRethrowException, TryBlock tryBlock, FilterBlock filter, CatchBlock catchBlock, FinallyBlock finallyBlock) – TrevJen 19 hours ago Log Name: Application Source: Office SharePoint Server Date: 4/13/2010 2:00:00 PM Event ID: 5553 Task Category: User Profiles Level: Error Keywords: Classic User: N/A Computer: nb-portal-01.clients.netboundary.local Description: failure trying to synch site 6fea15e2-0899-4c19-9016-44d77834c018 for ContentDB b2002b0b-3d4c-411a-8c4f-3d047ca9322c WebApp 3aff7051-455d-4a70-a377-5b1c36df618e. Exception message was Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED)). – TrevJen 18 hours ago

    Read the article

  • iptables DNS resolution

    - by Favolas
    I have a virtual machine with Fedora 19 acting as a router. This machine as an interface (p8p1) with the IP 172.16.1.254 that is connected to another machine (IP 172.16.1.1) that's simulating the external network. I've installed snort 2.9.2.2, applied the snortsam-2.9.2.2.diff.gz patch and installed snortsam 2.70 on the routermachine In snort.conf besides altering some RULE_PATH I believe I've only added the following line to the file. output alert_fwsam: 127.0.0.1:898/password After doing this two comands: ifconfig p8p1 promisc /usr/local/snort/bin/snort -v -i p8p1 If I ping from the external network to the router IP, I can see the info about the pings. One of the rules that I have is icmp-info.rules that as this single line: alert icmp $EXTERNAL_NET any -> $HOME_NET any (msg:"ICMP-INFO Echo Reply"; icode:0; itype:0; classtype:misc-activity; sid:408; rev:6;fwsam: src, 5 minutes;) snortsam.conf as this data: defaultkey password accept localhost keyinterval 30 minutes dontblock 192.168.1.1 # rede local rollbackhosts 50 rollbackthreshold 20 / 30 secs rollbacksleeptime 1 minute logfile /var/log/snort/snortsam.log loglevel 3 daemon nothreads # linha importante para gerar os bloqueios via iptables iptables p8p1 LOG bindip 127.0.0.1 Now I run this command: /usr/local/snort/bin/snort -u snort -i p8p1 -c /etc/snort/snort.conf -l /var/log/snort -Dq Terminal gives this message: Spawning daemon child... My daemon child 2080 lives... Daemon parent exiting (0) and when I runsnortsam in terminal i got this: SnortSam, v 2.70. Copyright (c) 2001-2009 Frank Knobbe . All rights reserved. Plugin 'fwsam': v 2.5, by Frank Knobbe Plugin 'fwexec': v 2.7, by Frank Knobbe Plugin 'pix': v 2.9, by Frank Knobbe Plugin 'ciscoacl': v 2.12, by Ali Basel <[email protected]> Plugin 'cisconullroute': v 2.5, by Frank Knobbe Plugin 'cisconullroute2': v 2.2, by Wouter de Jong <[email protected]> Plugin 'netscreen': v 2.10, by Frank Knobbe Plugin 'ipchains': v 2.8, by Hector A. Paterno <[email protected]> Plugin 'iptables': v 2.9, by Fabrizio Tivano <[email protected]>, Luis Marichal <[email protected]> Plugin 'ebtables': v 2.4, by Bruno Scatolin <[email protected]> Plugin 'watchguard': v 2.7, by Thomas Maier <[email protected]> Plugin 'email': v 2.12, by Frank Knobbe Plugin 'email-blocks-only': v 2.12, by Frank Knobbe Plugin 'snmpinterfacedown': v 2.3, by Ali BASEL <[email protected]> Plugin 'forward': v 2.8, by Frank Knobbe Parsing config file /etc/snortsam.conf... Linking plugin 'iptables'... Checking for existing state file "/var/db/snortsam.state". Found. Reading state file. Starting to listen for Snort alerts. and snortsam.log as an entry like this 2013/10/25, 10:15:17, -, 1, snortsam, Starting to listen for Snort alerts. Now, from the external machine I do ping 172.16.1.254 and it starts showing the info and an alert file is created in /var/log/snort/ that as the info about the PINGS. Something like: [**] [1:408:6] ICMP-INFO Echo Reply [**] [Classification: Misc activity] [Priority: 3] 10/25-10:35:16.061319 172.16.1.254 -> 172.16.1.1 ICMP TTL:64 TOS:0x0 ID:38720 IpLen:20 DgmLen:84 Type:0 Code:0 ID:1389 Seq:1 ECHO REPLY Also, if I run instead /usr/local/snort/bin/snort snort -v -i p8p1 i got this message: Running in packet dump mode --== Initializing Snort ==-- Initializing Output Plugins! Snort BPF option: snort pcap DAQ configured to passive. The DAQ version does not support reload. Acquiring network traffic from "p8p1". ERROR: Can't set DAQ BPF filter to 'snort' (pcap_daq_set_filter: pcap_compile: syntax error)! Fatal Error, Quitting.. So, this are my questions: Shouldn't snortsam block the PING? Is that DAQ error causing the problem? If so, How can I solve it?

    Read the article

  • cron.daily not running at the time it should?

    - by Mariano Martinez Peck
    My /etc/cron.daily scripts seem to be executing far later from what I understand they should. I am in Ubuntu and anacron is installed. If I do a sudo cat /var/log/syslog | grep cron I get something like: Aug 23 01:17:01 mymachine CRON[25171]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 02:17:01 mymachine CRON[25588]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 03:17:01 mymachine CRON[26026]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 03:25:01 mymachine CRON[30320]: (root) CMD (test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily )) Aug 23 04:17:01 mymachine CRON[26363]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 05:17:01 mymachine CRON[26770]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 06:17:01 mymachine CRON[27168]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 07:17:01 mymachine CRON[27547]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 07:30:01 mymachine CRON[2249]: (root) CMD (start -q anacron || :) Aug 23 07:30:02 mymachine anacron[2252]: Anacron 2.3 started on 2014-08-23 Aug 23 07:30:02 mymachine anacron[2252]: Will run job `cron.daily' in 5 min. Aug 23 07:30:02 mymachine anacron[2252]: Jobs will be executed sequentially Aug 23 07:35:02 mymachine anacron[2252]: Job `cron.daily' started As you can see, at 3:25 it tried to do something. But the cron.daily execution started really at 7:35. My /etc/crontab is: # /etc/crontab: system-wide crontab # Unlike any other crontab you don't have to run the `crontab' # command to install the new version when you edit this file # and files in /etc/cron.d. These files also have username fields, # that none of the other crontabs do. SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin # m h dom mon dow user command 17 * * * * root cd / && run-parts --report /etc/cron.hourly 25 3 * * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily ) 47 6 * * 7 root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.weekly ) 52 6 1 * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.monthly ) # From what I understand, daily scripts are indeed for 3:25. My /etc/anacrontab is: # /etc/anacrontab: configuration file for anacron # See anacron(8) and anacrontab(5) for details. SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin HOME=/root LOGNAME=root # These replace cron's entries 1 5 cron.daily run-parts --report /etc/cron.daily 7 10 cron.weekly run-parts --report /etc/cron.weekly @monthly 15 cron.monthly run-parts --report /etc/cron.monthly So...does someone know why my cron started to do something at 3:25 but then really start the jobs at 7:35? Also..as you can see in the log, hourly jobs are being executed at correct time: hour and 17 minutes, which is exactly what I have in /etc/crontab Finally, from the logs, it seems my daily jobs are being actually run by anacron rather than cron? So cron finds nothing to run (at 3:25) and then anacron runs the jobs at 7:35? If true, how can I fix this? Thanks in advance,

    Read the article

  • How to automate org-refile for multiple todo

    - by lawlist
    I'm looking to automate org-refile so that it will find all of the matches and re-file them to a specific location (but not archive). I found a fully automated method of archiving multiple todo, and I am hopeful to find or create (with some help) something similar to this awesome function (but for a different heading / location other than archiving): https://github.com/tonyday567/jwiegley-dot-emacs/blob/master/dot-org.el (defun org-archive-done-tasks () (interactive) (save-excursion (goto-char (point-min)) (while (re-search-forward "\* \\(None\\|Someday\\) " nil t) (if (save-restriction (save-excursion (org-narrow-to-subtree) (search-forward ":LOGBOOK:" nil t))) (forward-line) (org-archive-subtree) (goto-char (line-beginning-position)))))) I also found this (written by aculich), which is a step in the right direction, but still requires repeating the function manually: http://stackoverflow.com/questions/7509463/how-to-move-a-subtree-to-another-subtree-in-org-mode-emacs ;; I also wanted a way for org-refile to refile easily to a subtree, so I wrote some code and generalized it so that it will set an arbitrary immediate target anywhere (not just in the same file). ;; Basic usage is to move somewhere in Tree B and type C-c C-x C-m to mark the target for refiling, then move to the entry in Tree A that you want to refile and type C-c C-w which will immediately refile into the target location you set in Tree B without prompting you, unless you called org-refile-immediate-target with a prefix arg C-u C-c C-x C-m. ;; Note that if you press C-c C-w in rapid succession to refile multiple entries it will preserve the order of your entries even if org-reverse-note-order is set to t, but you can turn it off to respect the setting of org-reverse-note-order with a double prefix arg C-u C-u C-c C-x C-m. (defvar org-refile-immediate nil "Refile immediately using `org-refile-immediate-target' instead of prompting.") (make-local-variable 'org-refile-immediate) (defvar org-refile-immediate-preserve-order t "If last command was also `org-refile' then preserve ordering.") (make-local-variable 'org-refile-immediate-preserve-order) (defvar org-refile-immediate-target nil) "Value uses the same format as an item in `org-refile-targets'." (make-local-variable 'org-refile-immediate-target) (defadvice org-refile (around org-immediate activate) (if (not org-refile-immediate) ad-do-it ;; if last command was `org-refile' then preserve ordering (let ((org-reverse-note-order (if (and org-refile-immediate-preserve-order (eq last-command 'org-refile)) nil org-reverse-note-order))) (ad-set-arg 2 (assoc org-refile-immediate-target (org-refile-get-targets))) (prog1 ad-do-it (setq this-command 'org-refile))))) (defadvice org-refile-cache-clear (after org-refile-history-clear activate) (setq org-refile-targets (default-value 'org-refile-targets)) (setq org-refile-immediate nil) (setq org-refile-immediate-target nil) (setq org-refile-history nil)) ;;;###autoload (defun org-refile-immediate-target (&optional arg) "Set current entry as `org-refile' target. Non-nil turns off `org-refile-immediate', otherwise `org-refile' will immediately refile without prompting for target using most recent entry in `org-refile-targets' that matches `org-refile-immediate-target' as the default." (interactive "P") (if (equal arg '(16)) (progn (setq org-refile-immediate-preserve-order (not org-refile-immediate-preserve-order)) (message "Order preserving is turned: %s" (if org-refile-immediate-preserve-order "on" "off"))) (setq org-refile-immediate (unless arg t)) (make-local-variable 'org-refile-targets) (let* ((components (org-heading-components)) (level (first components)) (heading (nth 4 components)) (string (substring-no-properties heading))) (add-to-list 'org-refile-targets (append (list (buffer-file-name)) (cons :regexp (format "^%s %s$" (make-string level ?*) string)))) (setq org-refile-immediate-target heading)))) (define-key org-mode-map "\C-c\C-x\C-m" 'org-refile-immediate-target) It sure would be helpful if aculich, or some other maven, could please create a variable similar to (setq org-archive-location "~/0.todo.org::* Archived Tasks") so users can specify the file and heading, which is already a part of the org-archive-subtree functionality. I'm doing a search and mark because I don't have the wherewithal to create something like org-archive-location for this setup. EDIT: One step closer -- almost home free . . . (defun lawlist-auto-refile () (interactive) (beginning-of-buffer) (re-search-forward "\* UNDATED") (org-refile-immediate-target) ;; cursor must be on a heading to work. (save-excursion (re-search-backward "\* UNDATED") ;; must be written in such a way so that sub-entries of * UNDATED are not searched; or else infinity loop. (while (re-search-backward "\* \\(None\\|Someday\\) " nil t) (org-refile) ) ) )

    Read the article

  • Unable to remove limit on memory usage for PHP script.

    - by Jess Telford
    The Situation I am having an issue with a PHP script getting the following error message: Fatal error: Out of memory (allocated 359923712) (tried to allocate 72 bytes) in /path/to/piwik/core/DataTable.php on line 969 The script I'm running is: /path/to/piwik/misc/cron/archive.sh I am assuming the numbers are Bytes, which means that total is approximately 360MB. For all intents and purposes, I have increased the memory limits on the server well above 360MB, yet this is the number (give or take a byte) it consistently errors out at. Please note: This question is not about fixing a memory leak in the script, nor about why the script itself is using so much memory. The script is part of the Piwik archiving process, so I cannot just fix any memory leaks, etc. For more info on this script and why I am increasing the memory limit, see "How to setup auto archiving" The question Given that the script is attempting to use over 360MB of memory, which I cannot change, why does it not seem possible for me to increase the amount of memory available to php on my server? What I've tried Increasing PHP's memory_limit Given the php.ini file: php -i | grep php.ini Configuration File (php.ini) Path => /usr/local/lib Loaded Configuration File => /usr/local/lib/php.ini I have edited that file, so the memory_limit directive reads; memory_limit = -1 Restart Apache, and check the new value has stuck; $ php -i | grep memory_limit memory_limit => -1 => -1 Run the script, and get the same error. I've also tried 1G, 768M, etc, all to the same result (ie; no change). Update 22nd June: Based on Vangel's help, I have attempted to set post_max_size to 20M in combination with setting memory_limit. Again, this has no effect. Removing the memory limit on child processes of Apache I have found and edited the httpd.conf file to make sure there is no RLimitMEM directive. I then used WHM's Apache Configuration Memory Usage Restrictions to generate a restriction, which it claimed was at 1000M (and confirmed by checking httpd.conf). Both of these resulted in no change to the script erroring at 360MB. Increasing the per process memory limits of Linux The current limits set on the system: $ ulimit -m 524288 $ ulimit -v 524288 I have attempted to set both of these to unlimited: $ ulimit -m unlimited $ ulimit -v unlimited $ ulimit -m unlimited $ ulimit -v unlimited Once again, this has resulted in absolutely no improvement in my problem. My setup $ cat /etc/redhat-release CentOS release 5.5 (Final) $ uname -a Linux example.com 2.6.18-164.15.1.el5 #1 SMP Wed Mar 17 11:30:06 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux $ php -i | grep "PHP Version" PHP Version => 5.2.9 $ httpd -V Server version: Apache/2.0.63 Server built: Feb 2 2011 01:25:12 Cpanel::Easy::Apache v3.2.0 rev5291 Server's Module Magic Number: 20020903:13 Server loaded: APR 0.9.17, APR-UTIL 0.9.15 Compiled using: APR 0.9.17, APR-UTIL 0.9.15 Architecture: 64-bit Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D HTTPD_ROOT="/usr/local/apache" -D SUEXEC_BIN="/usr/local/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" Output of $ php -i: http://pastebin.com/EiRut6Nm

    Read the article

  • Email sent from Centos end up in user spam folder

    - by oObe
    I am facing this issue, I use the default postfix MTA in centos but the mail end up in user spam folder, but this does not seem to be a problem in Debian using exim4, both host have hostname and domain name configured, and relay mail through external smtp host. Both configuration and recieving email header are attached. The different seems that Debian has this additional (envelope tag) and (from) tag other than some minor syntax differences. Any help to resolve is appreciated. The IP address and DNS is masked as follow: 1.2.3.4 = My IP address smtp.host.com = external smtp host for my company [email protected] = account at smtp host centos.abc.com = Local centos server debian.abc.com = Local debian server Thanks. Centos main.cf config with the following params configured myhostname = centos.abc.com mydomain = abc.com myorigin = centos.abc.com relayhost = smtp.host.com Centos - User receiving mail header Return-Path: <[email protected]> Received: from 1.2.3.4 [1.2.3.4] by smtp.host.com with SMTP; Thu, 27 Sep 2012 13:36:49 +0800 Received: by centos.abc.com (Postfix, from userid 0) id 1E0637B89; Fri, 28 Sep 2012 13:36:39 +0800 (SGT) Return-Path: <[email protected]> Received: from 1.2.3.4 [1.2.3.4] by smtp.host.com with SMTP; Thu, 27 Sep 2012 13:36:49 +0800 Received: by centos.abc.com (Postfix, from userid 0) id 1E0637B89; Fri, 28 Sep 2012 13:36:39 +0800 (SGT) Date: Fri, 28 Sep 2012 13:36:39 +0800 To: [email protected] Subject: Test mail from centos User-Agent: Heirloom mailx 12.4 7/29/08 MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Message-Id: <[email protected]> From: [email protected] (root) X-SmarterMail-TotalSpamWeight: 0 X-Antivirus: avast! (VPS 120926-1, 27/09/2012), Inbound message X-Antivirus-Status: Clean http://i.imgur.com/7WAYX.jpg Debain exim4 config .... # This is a Debian specific file dc_eximconfig_configtype='smarthost' dc_other_hostnames='debian.abc.com' dc_local_interfaces='127.0.0.1 ; ::1' dc_readhost='debian.abc.com' dc_relay_domains='smtp.host.com' dc_minimaldns='false' dc_relay_nets='127.0.0.1' dc_smarthost='smtp.host.com' CFILEMODE='644' dc_use_split_config='false' dc_hide_mailname='true' dc_mailname_in_oh='true' dc_localdelivery='mail_spool' debian - User receiving mail header Return-Path: <[email protected]> Received: from 1.2.3.4 [1.2.3.4] by smtp.host.com with SMTP; Thu, 27 Sep 2012 15:02:53 +0800 Received: from root by debian.abc.com with local (Exim 4.72) (envelope-from <[email protected]>) id 1TH86d-00010v-G9 for [email protected]; Thu, 27 Sep 2012 15:01:55 +0800 Return-Path: <[email protected]> Received: from 1.2.3.4 [1.2.3.4] by smtp.host.com with SMTP; Thu, 27 Sep 2012 15:02:53 +0800 Received: from root by debian.abc.com with local (Exim 4.72) (envelope-from <[email protected]>) id 1TH86d-00010v-G9 for [email protected]; Thu, 27 Sep 2012 15:01:55 +0800 Date: Thu, 27 Sep 2012 15:01:55 +0800 Message-Id: <[email protected]> To: [email protected] Subject: Test from debian From: root <[email protected]> X-SmarterMail-TotalSpamWeight: 0 X-Antivirus: avast! (VPS 120926-1, 27/09/2012), Inbound message X-Antivirus-Status: Clean http://imgur.com/nMsMA.jpg

    Read the article

  • Openvpn issue with linux

    - by catsy
    So I've tried to setup openvpn, I followed some guide but it's stuck att "initialization sequence completed" with no connection and I can't find any working solution... here's the log: $Sun Sep 23 19:14:32 2012 OpenVPN 2.1.0 i486-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 20 2010 Enter Auth Username:pumpedup Enter Auth Password: Sun Sep 23 19:14:37 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Sun Sep 23 19:14:37 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Sun Sep 23 19:14:37 2012 LZO compression initialized Sun Sep 23 19:14:37 2012 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Sun Sep 23 19:14:38 2012 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Sun Sep 23 19:14:38 2012 Local Options hash (VER=V4): '41690919' Sun Sep 23 19:14:38 2012 Expected Remote Options hash (VER=V4): '530fdded' Sun Sep 23 19:14:38 2012 Socket Buffers: R=[163840-131072] S=[163840-131072] Sun Sep 23 19:14:38 2012 UDPv4 link local: [undef] Sun Sep 23 19:14:38 2012 UDPv4 link remote: [AF_INET]192.162.102.162:1194 Sun Sep 23 19:14:38 2012 TLS: Initial packet from [AF_INET]192.162.102.162:1194, sid=87a95723 a6d7b7f9 Sun Sep 23 19:14:38 2012 WARNING: this configuration may cache passwords in memory -- use the auth-nocache option to prevent this Sun Sep 23 19:14:38 2012 VERIFY OK: depth=1, /C=NV/ST=NV/L=nVPN/O=nVpn/CN=nVpn_CA/[email protected] Sun Sep 23 19:14:38 2012 VERIFY OK: depth=0, /C=NV/ST=NV/L=nVPN/O=nVpn/CN=server/[email protected] Sun Sep 23 19:14:39 2012 WARNING: 'link-mtu' is used inconsistently, local='link-mtu 1542', remote='link-mtu 6042' Sun Sep 23 19:14:39 2012 WARNING: 'tun-mtu' is used inconsistently, local='tun-mtu 1500', remote='tun-mtu 6000' Sun Sep 23 19:14:39 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Sun Sep 23 19:14:39 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sun Sep 23 19:14:39 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Sun Sep 23 19:14:39 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sun Sep 23 19:14:39 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Sun Sep 23 19:14:39 2012 [server] Peer Connection Initiated with [AF_INET]192.162.102.162:1194 Sun Sep 23 19:14:41 2012 SENT CONTROL [server]: 'PUSH_REQUEST' (status=1) Sun Sep 23 19:14:41 2012 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1,dhcp-option DNS 8.8.8.8,dhcp-option DNS 8.8.8.8,route 10.102.162.1,topology net30,ping 10,ping-restart 120,ifconfig 10.102.162.6 10.102.162.5' Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: timers and/or timeouts modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: --ifconfig/up options modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: route options modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified Sun Sep 23 19:14:41 2012 ROUTE default_gateway=10.0.2.2 Sun Sep 23 19:14:41 2012 TUN/TAP device tun0 opened Sun Sep 23 19:14:41 2012 TUN/TAP TX queue length set to 100 Sun Sep 23 19:14:41 2012 /sbin/ifconfig tun0 10.102.162.6 pointopoint 10.102.162.5 mtu 1500 Sun Sep 23 19:14:41 2012 /sbin/route add -net 192.162.102.162 netmask 255.255.255.255 gw 10.0.2.2 Sun Sep 23 19:14:41 2012 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 /sbin/route add -net 10.102.162.1 netmask 255.255.255.255 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 Initialization Sequence Completed

    Read the article

  • How to delete files and folders that cannot be deleted?

    - by glenneroo
    I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. I ran chkdsk again, this time: chkdsk /f /r. Produced no messages. Same result when deleting. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because these (empty) directories are still not deleteable, C:\1\2\Favorites\Wien\What To Do.. C:\1\2\Favorites\Photography\FIRE Same error as above: Here is what Explorer properties shows for both folders: Update #4 (another partial solution): Using harrymc's answer combined with thoroughly reading through this amazing MS-KB article which contains nearly everyone's idea and then some, inconspicuously titled: You cannot delete a file or a folder on an NTFS file system volume. I was able to delete the 2nd folder C:\1\2\Favorites\Photography\FIRE - the problem being that there was an invisible trailing space at the end. I got lucky when I did an auto-complete whilst playing around with the del "\\?\<path>" command which he suggested. NOTE: A normal del did NOT work, nor did deleting from explorer. Now all that is left is the first directory C:\1\2\Favorites\Wien\What To Do.. (yes I tried endlessly with multiple combinations of the above solution ;) Keep 'em coming! =)

    Read the article

  • Downgrade OpenSSL on CentOS 6.5

    - by byyyk
    Application I use requires OpenSSL 0.9.8, which was already installed (0.9.8e to be specific) on my CentOS alongside 1.0.1e which unfortunately is used by default. I tried to change libssl.so.10 symbolic link to point to the older version like so: [mckulpa@nuance-vm ~]$ ldd /usr/bin/openssl /usr/bin/openssl: /usr/lib64/libssl.so.10: no version information available (required by /usr/bin/openssl) linux-vdso.so.1 => (0x00007fff2edff000) libssl.so.10 => /usr/lib64/libssl.so.10 (0x00007f664457c000) libgssapi_krb5.so.2 => /lib64/libgssapi_krb5.so.2 (0x0000003927600000) libkrb5.so.3 => /lib64/libkrb5.so.3 (0x0000003926200000) libcom_err.so.2 => /lib64/libcom_err.so.2 (0x0000003925a00000) libk5crypto.so.3 => /lib64/libk5crypto.so.3 (0x0000003926e00000) libcrypto.so.10 => /usr/lib64/libcrypto.so.10 (0x0000003927200000) libdl.so.2 => /lib64/libdl.so.2 (0x000000391a600000) libz.so.1 => /lib64/libz.so.1 (0x000000391aa00000) libc.so.6 => /lib64/libc.so.6 (0x0000003919e00000) libcrypto.so.6 => /usr/lib64/libcrypto.so.6 (0x00007f664421d000) libkrb5support.so.0 => /lib64/libkrb5support.so.0 (0x0000003925e00000) libkeyutils.so.1 => /lib64/libkeyutils.so.1 (0x0000003926a00000) libresolv.so.2 => /lib64/libresolv.so.2 (0x000000391be00000) libpthread.so.0 => /lib64/libpthread.so.0 (0x000000391a200000) /lib64/ld-linux-x86-64.so.2 (0x0000003919600000) libselinux.so.1 => /lib64/libselinux.so.1 (0x000000391b600000) [mckulpa@nuance-vm ~]$ export LD_LIBRARY_PATH=~/libs:$LD_LIBRARY_PATH [mckulpa@nuance-vm ~]$ echo $LD_LIBRARY_PATH /home/mckulpa/libs:/usr/local/Nuance/Recognizer_Service/amd64/lib:/usr/local/Nuance/OAM/x86/lib:/usr/local/Nuance/Common/x86/lib:/usr/local/Nuance/Common/amd64/lib [mckulpa@nuance-vm ~]$ ldd /usr/bin/openssl /usr/bin/openssl: /home/mckulpa/libs/libssl.so.10: no version information available (required by /usr/bin/openssl) linux-vdso.so.1 => (0x00007fff91dbc000) libssl.so.10 => /home/mckulpa/libs/libssl.so.10 (0x00007ffe1af50000) libgssapi_krb5.so.2 => /lib64/libgssapi_krb5.so.2 (0x0000003927600000) libkrb5.so.3 => /lib64/libkrb5.so.3 (0x0000003926200000) libcom_err.so.2 => /lib64/libcom_err.so.2 (0x0000003925a00000) libk5crypto.so.3 => /lib64/libk5crypto.so.3 (0x0000003926e00000) libcrypto.so.10 => /usr/lib64/libcrypto.so.10 (0x0000003927200000) libdl.so.2 => /lib64/libdl.so.2 (0x000000391a600000) libz.so.1 => /lib64/libz.so.1 (0x000000391aa00000) libc.so.6 => /lib64/libc.so.6 (0x0000003919e00000) libcrypto.so.6 => /usr/lib64/libcrypto.so.6 (0x00007ffe1abd9000) libkrb5support.so.0 => /lib64/libkrb5support.so.0 (0x0000003925e00000) libkeyutils.so.1 => /lib64/libkeyutils.so.1 (0x0000003926a00000) libresolv.so.2 => /lib64/libresolv.so.2 (0x000000391be00000) libpthread.so.0 => /lib64/libpthread.so.0 (0x000000391a200000) /lib64/ld-linux-x86-64.so.2 (0x0000003919600000) libselinux.so.1 => /lib64/libselinux.so.1 (0x000000391b600000) [mckulpa@nuance-vm ~]$ ls -l libs total 316 -rwxr-xr-x. 1 mckulpa mckulpa 321224 05-28 14:59 libssl.so.0.9.8e lrwxrwxrwx. 1 mckulpa mckulpa 16 05-28 15:18 libssl.so.10 -> libssl.so.0.9.8e but all I get is a warning and still the 1.0.1e version is printed out: [mckulpa@nuance-vm ~]$ openssl version openssl: /home/mckulpa/libs/libssl.so.10: no version information available (required by openssl) OpenSSL 1.0.1e-fips 11 Feb 2013 Any ideas how to do this properly?

    Read the article

  • What is the best server or Ip address to use for prolonged testing?

    - by eldorel
    I usually run uptime/latency tests against (and from) two servers that we own at different sites and until recently I've used the google dns servers as a control group. However, I've realized there is a potential problem with monitoring latency over extended periods of time. Almost all of the major service providers are using ANYCAST. For short tests this doesn't matter, but I need to run a set of tests for at least a week to try and catch an intermittent problem, and a change in the anycast priority while trying to test latency will cause the latency values for that server to change accordingly. Since I'm submitting graphs of this data to the ISP, I need to avoid/account for as many variables as possible. Spikes in the data for only one of the tested servers will only cause headaches. So can anyone recommend servers that: are not using anycast are owned by an entity that has a good uptime reputation (so they can't claim that the problem is server-side) will respond to ICMP requests Have an available service that runs on TCP/UDP (http or dns preferably) Wont consider an automated request every 10 minutes to be abuse Are accessible from anywhere in the world Are not local to the isp ( consider this an investigation of a hostile party ) Thanks in advance. Edit: added #6 and #7 above. More info: I am attempting to demonstrate a network problem for an entire node of our local ISP's network. They are actively blaming the issue on the equipment installed at the customer sites (our backup site is one of these), and refuse to escalate the problem. (even though 2 of these businesses have ISP provided modems, and all of us have completely different routers/services running) I am already quite familiar with the need to test an isp controlled IP, but they are actively dropping all packets targeted at gateway ip addresses and are only passing traffic addressed beyond the gateways. So to demonstrate the issue, I am sending packets to other systems in the same node, systems one hop away from the affected node, and systems completely outside the network. Unfortunately, all of the systems I have currently are either administered directly by myself, or by people who are biased enough to assist me. I need to have several systems included in the trace/log/graphs that are 100% not in the control of either myself or the isp so that the graphs have a stable/unbiased control group. These requirements are straight from legal, I'm just trying to make sure that everything that could be argued to invalidate the data is already covered. In Summary: I need to be able to show tcp/udp/icmp as 3 separate data points, and I need to be able to show the connections inside the local node, from local node to another nearby node, from those 2 nodes to the internet, and through the internet to both verifiable servers and a control group that I have no control over whatsoever. Again, Google/opendns/yahoo/msn/facebook/etc all use anycast, which throws the numbers off every time the anycast caches expire, so I need suggestions of an IP or server that is available for this type of testing. I was hoping someone knew of a system run by someone such as ISC or ICANN, or perhaps even a .gov server (fcc or nsa maybe?) setup for this type of testing. Thanks again.

    Read the article

  • IPv6 host route is deleted after PMTU expires

    - by SAPikachu
    I am experimenting my new IPv6 tunnel setup between my local Ubuntu box and a scratch Linode. I set up some docker containers, configured 6in4 tunnel server and IPv6 forwarding on the Linode: # uname -a Linux argo 3.15.4-x86_64-linode45 #1 SMP Mon Jul 7 08:42:36 EDT 2014 x86_64 x86_64 x86_64 GNU/Linux # ip addr .. snipped .. 48: sit-sapikachu: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1472 qdisc noqueue state UNKNOWN group default link/sit 106.185.41.115 peer 1.2.3.4 inet6 fd00::1/64 scope global valid_lft forever preferred_lft forever inet6 fe80::6ab9:2973/64 scope link valid_lft forever preferred_lft forever 13: docker0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default link/ether 56:84:7a:fe:97:99 brd ff:ff:ff:ff:ff:ff inet 172.17.42.1/16 scope global docker0 valid_lft forever preferred_lft forever inet6 fc00::1/64 scope global valid_lft forever preferred_lft forever inet6 fe80::5484:7aff:fefe:9799/64 scope link valid_lft forever preferred_lft forever // Docker containers are bridged to docker0 On my local box, I configured a 6in4 tunnel interface to connect to the Linode box, and added a host route to one of the docker container: # uname -a Linux sapikachu-netbox 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux # ip addr .. snipped .. 16: sit-argo: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN group default link/sit 0.0.0.0 peer 106.185.41.115 inet6 fd00::2/64 scope global valid_lft forever preferred_lft forever inet6 fe80::a97:302/64 scope link valid_lft forever preferred_lft forever inet6 fe80::ac19:1/64 scope link valid_lft forever preferred_lft forever inet6 fe80::c0a8:1f0/64 scope link valid_lft forever preferred_lft forever inet6 fe80::c0a8:1fa/64 scope link valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether *** brd ff:ff:ff:ff:ff:ff .. snipped .. inet6 fd00:0:1::1/64 scope global valid_lft forever preferred_lft forever inet6 fe80::2e0:6fff:fe0e:365e/64 scope link valid_lft forever preferred_lft forever # ip route replace fc00::1875:8606:d8c1:8a9d via fd00::1 # Add route to docker container # ip -6 route .. snipped unrelated routes fc00::1875:8606:d8c1:8a9d via fd00::1 dev sit-argo metric 1024 expires 590sec mtu 1472 fd00::/64 dev sit-argo proto kernel metric 256 fd00:0:1::/64 dev eth0 proto kernel metric 256 fe80::/64 dev sit-argo proto kernel metric 256 (Note that tunnel MTU on my local box is different from the server, this is intentional for testing) After adding the host route to the docker container (fc00::1875:8606:d8c1:8a9d), I can ping the container without problem until the route expires. After that I couldn't get reply any more. If I run ip -6 route in a few seconds after expiration, expiration time of the host route will be a negative number: fc00::1875:8606:d8c1:8a9d via fd00::1 dev sit-argo metric 1024 expires -1sec And output of ip route get fc00::1875:8606:d8c1:8a9d shows that it is routed to my default IPv6 gateway (which fails to route it correctly of course, since the address is not globally routable). After some time, the host route disappears without a trace. This problem won't happen if I do either one of the following things: Set MTU of tunnel on my local box to be the same as the server (1472). The route won't have expiration time in both ip -6 route and ip route get in this case. Instead of adding a host route, add a route with network mask (even /127 works). In this case ip -6 route shows the route without expiration time, ip route get shows expiration time but it will be correctly refreshed after expiration. Although this problem can be easily resolved, I am curious to know why this happens. Is there error in my configuration, or is this a kernel bug?

    Read the article

  • Can spliting an access database cause printer and reporting issues?

    - by leeand00
    We have a setup in which our users log into an access database using MS Access 2003 over an RDP connection. The user's login to their own machines first using a roaming profile. They then click an rdp connection file on the desktop and login to the remote server, via RDP, where they use MS Access as the shell; they don't have any access to any of explorer.exe features such as the start menu. The database they are logging into is more of an application, and provides functionality for entering data, querying data, and running reports via form based menus. It all worked pretty well until we split the database as it was nearing 2GBs in size. We moved out the payroll data into a separate partition, a database with the same name in a different folder, both of them on the server. Only two tables were moved into this new database partition, and they were re-linked as external tables in the new partition. Now while everything appears to be working fine data-wise after the split, there's a new issue when our users login via RDP and attempt to run reports: often the report will not display and instead the user sees an error about the click event of the form. At first I didn't even know it was printer-related, as we didn't really change anything related to the printers as far as I knew. Confused about the error, I talked to the guy who previously worked here and who was in charge of splitting the database, and he told me to tell the users to set their default printers (on their local machines, not on the server) to the "printer" Microsoft XPS Document Writer which isn't a physical printer at all. This allowed the user's to display their reports, but if they want to print out reports, they are required to go to the File menu and select Print, clicking the print icon on the toolbar takes them to a Save As... dialog as would be expected when using the Microsoft XPS Document Writer as your default printer. It's easy to tell if the user is having a problem because a quick mouseover of the printer icon will yield a tooltip of (none) when they cannot access their reports, and a tooltip of Microsoft XPS Document Writer when they can view the reports. If the user's printer is set to anything other than Microsoft XPS Document Writer as the default on their local machine, then (none) is always displayed when they rdp to the database. The RDP settings are setup to transfer the local printer to the server. Telling the users to do this to print has been more of a band-aid on the whole situation until we find a better solution and an explanation as to why splitting a database would prevent users from printing or even viewing access database reports. Which is why I'm here asking this question. Also of note all the printers on the network now show up on the server so that when the users do click File->Print to print their reports on a physical printer, they have to look through a huge list of printers to find theirs in the dropdown. So the little band-aid fix we have is not ideal. Previously, only the printers on the user's local machine displayed here, and not all the printers on the network. My co-worker seems to think this has something to do with permissions, I personally think it has to do with roaming profiles, and Group Policies which is what I've been reading up on. I really don't know how to fix this or how it is related to splitting the database.

    Read the article

  • how to remove obsolete device and network entries? Device manager "uninstall" option has no effect

    - by Gizmo
    I am trying to remove a few "obsolete" things which annoy me (because I like to have everything cleen, working and not interferring with each other, fresh, etc..). I tried looking for solutions without any help, so here I am to ask. My first part is about removing obsolete networks, let me explain by showing the ipconfig output: C:\windows\system32>ipconfig Windows IP Configuration Wireless LAN adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Local Area Connection* 9: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Ethernet adapter LAN: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wi-Fi: Connection-specific DNS Suffix . : home Link-local IPv6 Address . . . . . : fe80::c129:8d57:bbd1:3564%10 IPv4 Address. . . . . . . . . . . : 192.168.2.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.254 Tunnel adapter isatap.home: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : home C:\windows\system32> Specificalyy the first two adapter entries annoy me because the adapters are not visible in the network connection menu (invisible folder / file visibility set to "show"): And here is the second problem altogether with the first one: No matter what I click/do, Uninstall option has no effect on the multiplexor driver. (bridging stuff, right?) I really want to remove the Wireless LAN adapter Local Area Connection entries and the adapter multiplexor stuff but it's impossible? Why is this? How can I remove them anyway?

    Read the article

  • Cannot determine ethernet address for proxy ARP on PPTP

    - by Linux Intel
    I installed pptp server on a centos 6 64bit server PPTP Server ip : 55.66.77.10 PPTP Local ip : 10.0.0.1 Client1 IP : 10.0.0.60 centos 5 64bit Client2 IP : 10.0.0.61 centos5 64bit PPTP Server can ping Client1 And client 1 can ping PPTP Server PPTP Server can ping Client2 And client 2 can ping PPTP Server The problem is client 1 can not ping Client 2 and i get this error also on PPTP server error log Cannot determine ethernet address for proxy ARP Ping from Client2 to Client1 PING 10.0.0.60 (10.0.0.60) 56(84) bytes of data. --- 10.0.0.60 ping statistics --- 6 packets transmitted, 0 received, 100% packet loss, time 5000ms route -n on PPTP Server Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.60 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.0.0.61 0.0.0.0 255.255.255.255 UH 0 0 0 ppp1 55.66.77.10 0.0.0.0 255.255.255.248 U 0 0 0 eth0 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0 0.0.0.0 55.66.77.19 0.0.0.0 UG 0 0 0 eth0 route -n On Client 1 Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 55.66.77.10 70.14.13.19 255.255.255.255 UGH 0 0 0 eth0 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth1 0.0.0.0 70.14.13.19 0.0.0.0 UG 0 0 0 eth0 route -n On Client 2 Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 55.66.77.10 84.56.120.60 255.255.255.255 UGH 0 0 0 eth1 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0 0.0.0.0 84.56.120.60 0.0.0.0 UG 0 0 0 eth1 cat /etc/ppp/options.pptpd on PPTP server ############################################################################### # $Id: options.pptpd,v 1.11 2005/12/29 01:21:09 quozl Exp $ # # Sample Poptop PPP options file /etc/ppp/options.pptpd # Options used by PPP when a connection arrives from a client. # This file is pointed to by /etc/pptpd.conf option keyword. # Changes are effective on the next connection. See "man pppd". # # You are expected to change this file to suit your system. As # packaged, it requires PPP 2.4.2 and the kernel MPPE module. ############################################################################### # Authentication # Name of the local system for authentication purposes # (must match the second field in /etc/ppp/chap-secrets entries) name pptpd # Strip the domain prefix from the username before authentication. # (applies if you use pppd with chapms-strip-domain patch) #chapms-strip-domain # Encryption # (There have been multiple versions of PPP with encryption support, # choose with of the following sections you will use.) # BSD licensed ppp-2.4.2 upstream with MPPE only, kernel module ppp_mppe.o # {{{ refuse-pap refuse-chap refuse-mschap # Require the peer to authenticate itself using MS-CHAPv2 [Microsoft # Challenge Handshake Authentication Protocol, Version 2] authentication. require-mschap-v2 # Require MPPE 128-bit encryption # (note that MPPE requires the use of MSCHAP-V2 during authentication) require-mppe-128 # }}} # OpenSSL licensed ppp-2.4.1 fork with MPPE only, kernel module mppe.o # {{{ #-chap #-chapms # Require the peer to authenticate itself using MS-CHAPv2 [Microsoft # Challenge Handshake Authentication Protocol, Version 2] authentication. #+chapms-v2 # Require MPPE encryption # (note that MPPE requires the use of MSCHAP-V2 during authentication) #mppe-40 # enable either 40-bit or 128-bit, not both #mppe-128 #mppe-stateless # }}} # Network and Routing # If pppd is acting as a server for Microsoft Windows clients, this # option allows pppd to supply one or two DNS (Domain Name Server) # addresses to the clients. The first instance of this option # specifies the primary DNS address; the second instance (if given) # specifies the secondary DNS address. #ms-dns 10.0.0.1 #ms-dns 10.0.0.2 # If pppd is acting as a server for Microsoft Windows or "Samba" # clients, this option allows pppd to supply one or two WINS (Windows # Internet Name Services) server addresses to the clients. The first # instance of this option specifies the primary WINS address; the # second instance (if given) specifies the secondary WINS address. #ms-wins 10.0.0.3 #ms-wins 10.0.0.4 # Add an entry to this system's ARP [Address Resolution Protocol] # table with the IP address of the peer and the Ethernet address of this # system. This will have the effect of making the peer appear to other # systems to be on the local ethernet. # (you do not need this if your PPTP server is responsible for routing # packets to the clients -- James Cameron) proxyarp # Normally pptpd passes the IP address to pppd, but if pptpd has been # given the delegate option in pptpd.conf or the --delegate command line # option, then pppd will use chap-secrets or radius to allocate the # client IP address. The default local IP address used at the server # end is often the same as the address of the server. To override this, # specify the local IP address here. # (you must not use this unless you have used the delegate option) #10.8.0.100 # Logging # Enable connection debugging facilities. # (see your syslog configuration for where pppd sends to) debug # Print out all the option values which have been set. # (often requested by mailing list to verify options) #dump # Miscellaneous # Create a UUCP-style lock file for the pseudo-tty to ensure exclusive # access. lock # Disable BSD-Compress compression nobsdcomp # Disable Van Jacobson compression # (needed on some networks with Windows 9x/ME/XP clients, see posting to # poptop-server on 14th April 2005 by Pawel Pokrywka and followups, # http://marc.theaimsgroup.com/?t=111343175400006&r=1&w=2 ) novj novjccomp # turn off logging to stderr, since this may be redirected to pptpd, # which may trigger a loopback nologfd # put plugins here # (putting them higher up may cause them to sent messages to the pty) cat /etc/ppp/options.pptp on Client1 and Client2 ############################################################################### # $Id: options.pptp,v 1.3 2006/03/26 23:11:05 quozl Exp $ # # Sample PPTP PPP options file /etc/ppp/options.pptp # Options used by PPP when a connection is made by a PPTP client. # This file can be referred to by an /etc/ppp/peers file for the tunnel. # Changes are effective on the next connection. See "man pppd". # # You are expected to change this file to suit your system. As # packaged, it requires PPP 2.4.2 or later from http://ppp.samba.org/ # and the kernel MPPE module available from the CVS repository also on # http://ppp.samba.org/, which is packaged for DKMS as kernel_ppp_mppe. ############################################################################### # Lock the port lock # Authentication # We don't need the tunnel server to authenticate itself noauth # We won't do PAP, EAP, CHAP, or MSCHAP, but we will accept MSCHAP-V2 # (you may need to remove these refusals if the server is not using MPPE) refuse-pap refuse-eap refuse-chap refuse-mschap # Compression # Turn off compression protocols we know won't be used nobsdcomp nodeflate # Encryption # (There have been multiple versions of PPP with encryption support, # choose which of the following sections you will use. Note that MPPE # requires the use of MSCHAP-V2 during authentication) # # Note that using PPTP with MPPE and MSCHAP-V2 should be considered # insecure: # http://marc.info/?l=pptpclient-devel&m=134372640219039&w=2 # https://github.com/moxie0/chapcrack/blob/master/README.md # http://technet.microsoft.com/en-us/security/advisory/2743314 # http://ppp.samba.org/ the PPP project version of PPP by Paul Mackarras # ppp-2.4.2 or later with MPPE only, kernel module ppp_mppe.o # If the kernel is booted in FIPS mode (fips=1), the ppp_mppe.ko module # is not allowed and PPTP-MPPE is not available. # {{{ # Require MPPE 128-bit encryption #require-mppe-128 # }}} # http://mppe-mppc.alphacron.de/ fork from PPP project by Jan Dubiec # ppp-2.4.2 or later with MPPE and MPPC, kernel module ppp_mppe_mppc.o # {{{ # Require MPPE 128-bit encryption #mppe required,stateless # }}} IPtables is stopped on clients and server, Also net.ipv4.ip_forward = 1 is enabled on PPTP Server. How can i solve this problem .?

    Read the article

  • Getting client denied when accessing a wsgi graphite script

    - by Dr BDO Adams
    I'm trying to set up graphite on my Mac OS X 10.7 lion, i've set up apache to call the python graphite script via WSGI, but when i try to access it, i get a forbiden from apache and in the error log. "client denied by server configuration: /opt/graphite/webapp/graphite.wsgi" I've checked that the scripts location is allowed in httpd.conf, and the permissions of the file, but they seem correct. What do i have to do to get access. Below is the httpd.conf, which is nearly the graphite example. <IfModule !wsgi_module.c> LoadModule wsgi_module modules/mod_wsgi.so </IfModule> WSGISocketPrefix /usr/local/apache/run/wigs <VirtualHost _default_:*> ServerName graphite DocumentRoot "/opt/graphite/webapp" ErrorLog /opt/graphite/storage/log/webapp/error.log CustomLog /opt/graphite/storage/log/webapp/access.log common WSGIDaemonProcess graphite processes=5 threads=5 display-name='%{GROUP}' inactivity-timeout=120 WSGIProcessGroup graphite WSGIApplicationGroup %{GLOBAL} WSGIImportScript /opt/graphite/conf/graphite.wsgi process-group=graphite application-group=%{GLOBAL} # XXX You will need to create this file! There is a graphite.wsgi.example # file in this directory that you can safely use, just copy it to graphite.wgsi WSGIScriptAlias / /opt/graphite/webapp/graphite.wsgi Alias /content/ /opt/graphite/webapp/content/ <Location "/content/"> SetHandler None </Location> # XXX In order for the django admin site media to work you Alias /media/ "/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site- packages/django/contrib/admin/media/" <Location "/media/"> SetHandler None </Location> # The graphite.wsgi file has to be accessible by apache. <Directory "/opt/graphite/webapp/"> Options +ExecCGI Order deny,allow Allow from all </Directory> </VirtualHost> Can you help?

    Read the article

  • Cmdlets for AD CS deployment: Install-ADcsCertificationAuthority cmdlet failing when attempting to install an offline policy CA

    - by red888
    I installed an offline root CA without issue using this command: Install-ADcsCertificationAuthority ` -OverwriteExistingKey ` <#In the case of a re-installation#> ` -AllowAdministratorInteraction ` -CACommonName ` "LAB Corporate Root CA" ` -CADistinguishedNameSuffix ` 'O=LAB Inc.,C=US' ` -CAType ` StandaloneRootCA ` -CryptoProviderName ` "RSA#Microsoft Software Key Storage Provider" ` -HashAlgorithmName ` SHA256 ` -KeyLength ` 2048 ` -ValidityPeriod ` Years ` -ValidityPeriodUnits ` 20 ` -DatabaseDirectory ` 'E:\CAData\CertDB' ` -LogDirectory ` 'E:\CAData\CertLog' ` -Verbose I installed the root CA's cert and CRl on the policy CA, installed the AD CS binaries, and attempted to run this command to install the policy CA and export a req file: Install-ADcsCertificationAuthority ` -OverwriteExistingKey ` <#In the case of a re-installation#> ` -AllowAdministratorInteraction ` -CACommonName ` "LAB Corporate Policy Internal CA" ` -CADistinguishedNameSuffix ` 'O=LAB Inc.,C=US' ` -CAType ` StandaloneSubordinateCA ` -ParentCA ` rootca ` -OutputCertRequestFile ` 'e:\polca-int.req' ` -CryptoProviderName ` "RSA#Microsoft Software Key Storage Provider" ` -HashAlgorithmName ` SHA256 ` -KeyLength ` 2048 ` -ValidityPeriod ` Years ` -ValidityPeriodUnits ` 10 ` -DatabaseDirectory ` 'E:\CAData\CertDB' ` -LogDirectory ` 'E:\CAData\CertLog' ` -Verbose When doing this I receive the following error: VERBOSE: Calling InitializeDefaults method on the setup object. Install-ADcsCertificationAuthority : At line:1 char:1 + Install-ADcsCertificationAuthority ` + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + CategoryInfo : InvalidArgument: (:) [Install-AdcsCertificationA uthority], CertificationAuthoritySetupException + FullyQualifiedErrorId : ValidateParameters,Microsoft.CertificateServices .Deployment.Commands.CA.InstallADCSCertificationAuthority Is there a parameter I am entering incorrectly or something?

    Read the article

  • Existing open source software for wireless mesh networking?

    - by user70352
    Hello! My goal: Build a wireless mesh network with some ALIX 2D2 (500 MHz AMD Geode LX800 x86 CPU, 256MB RAM, Atheros wireless card) Aside from working like a normal wireless mesh network users should be able to read/write data from/to the ALIX Boxes and the ALIX boxes should be able to process data. Questions: Should I try to flash dd-wrt x86, voyage linux (linux.voyage.hk) or something else? What (open source) software should I look into before I start? Should I use a 'server' for data storage and processing instead of the ALIX boxes? Is it even possible to use the ALIX boxes for routing AND data storage and processing? Final notes: Data can be anything, for example, I want to setup a wireless mesh using the OLSRD protocol so my whole town gets wifi and can access songs on the network. It's not for that, but that's the idea. I'm not afraid of programing, compiling or working with *nix. This is mostly 'for fun' rather than for practicality. Thanks in advance for any feedback.

    Read the article

  • JSF Portlets in Liferay on JBoss

    - by JBirch
    I'm currently looking at working with and deploying JSF portlets into Liferay 6.0.5, sitting on JBoss 5.1.0. I ran into a lot of trouble trying to port some JSF-y/Seam-y/EJB-y stuff I had lying around, so I thought I'd start simple and work my way up. I could generate generic portlets using the NetBeans Maven archetype for Liferay portlets absolutely fine, but it's rather irrelevant because I wanted JSF portlets I took an example JSF portlet from http://www.liferay.com/downloads/liferay-portal/community-plugins/-/software_catalog/products/5546866 and attempted to deploy into a clean, vanilla installation of Liferay 6.0.5/JBoss 5.1.0 to no avail. The log messages are reproduced at the end of this. This particular example was actually tested for GlassFish and Tomcat, so it's not particularly helpful considering I'm deplying into JBoss. I tried ripping it apart and removing the jsf implementation contained within as there is a jsf implementation shipped with JBoss (Mojarra 1.2_12, in this case). 03:16:17,173 INFO [PortletAutoDeployListener] Copying portlets for /usr/local/[REDACTED]/liferay/liferay-portal-6.0.5/deploy/richfaces-sun-jsf1.2-facelets-portlet-1.2.war Expanding: /usr/local/[REDACTED]/liferay/liferay-portal-6.0.5/deploy/richfaces-sun-jsf1.2-facelets-portlet-1.2.war into /tmp/20110201031617188 Copying 1 file to /tmp/20110201031617188/WEB-INF Copying 1 file to /tmp/20110201031617188/WEB-INF/classes Copying 1 file to /tmp/20110201031617188/WEB-INF/classes Copying 47 files to /usr/local/[REDACTED]/liferay/liferay-portal-6.0.5/jboss-5.1.0/server/default/deploy/richfaces-sun-jsf1.2-facelets-portlet.war Copying 1 file to /usr/local/[REDACTED]/liferay/liferay-portal-6.0.5/jboss-5.1.0/server/default/deploy/richfaces-sun-jsf1.2-facelets-portlet.war Deleting directory /tmp/20110201031617188 03:16:20,075 INFO [PortletAutoDeployListener] Portlets for /usr/local/[REDACTED]/liferay/liferay-portal-6.0.5/deploy/richfaces-sun-jsf1.2-facelets-portlet-1.2.war copied successfully. Deployment will start in a few seconds. 03:16:23,632 INFO [TomcatDeployment] deploy, ctxPath=/richfaces-sun-jsf1.2-facelets-portlet 03:16:24,446 INFO [PortletHotDeployListener] Registering portlets for richfaces-sun-jsf1.2-facelets-portlet 03:16:24,492 INFO [faces] Init GenericFacesPortlet for portlet 1 03:16:24,495 INFO [faces] Bridge class name is org.jboss.portletbridge.AjaxPortletBridge 03:16:24,509 INFO [faces] The bridge does not support doHeaders method 03:16:24,510 INFO [faces] GenericFacesPortlet for portlet 1 initialized 03:16:24,555 INFO [PortletHotDeployListener] 1 portlet for richfaces-sun-jsf1.2-facelets-portlet is available for use 03:16:24,627 SEVERE [webapp] Initialization of the JSF runtime either failed or did not occurr. Review the server''s log for details. java.lang.InstantiationException: org.jboss.portletbridge.context.FacesContextFactoryImpl at java.lang.Class.newInstance0(Class.java:340) at java.lang.Class.newInstance(Class.java:308) at javax.faces.FactoryFinder.getImplGivenPreviousImpl(FactoryFinder.java:537) at javax.faces.FactoryFinder.getImplementationInstance(FactoryFinder.java:394) at javax.faces.FactoryFinder.access$400(FactoryFinder.java:135) at javax.faces.FactoryFinder$FactoryManager.getFactory(FactoryFinder.java:717) at javax.faces.FactoryFinder.getFactory(FactoryFinder.java:239) at javax.faces.webapp.FacesServlet.init(FacesServlet.java:164) at org.apache.catalina.core.StandardWrapper.loadServlet(StandardWrapper.java:1048) at org.apache.catalina.core.StandardWrapper.load(StandardWrapper.java:950) at org.apache.catalina.core.StandardContext.loadOnStartup(StandardContext.java:4122) at org.apache.catalina.core.StandardContext.start(StandardContext.java:4421) at org.jboss.web.tomcat.service.deployers.TomcatDeployment.performDeployInternal(TomcatDeployment.java:310) at org.jboss.web.tomcat.service.deployers.TomcatDeployment.performDeploy(TomcatDeployment.java:142) at org.jboss.web.deployers.AbstractWarDeployment.start(AbstractWarDeployment.java:461) at org.jboss.web.deployers.WebModule.startModule(WebModule.java:118) at org.jboss.web.deployers.WebModule.start(WebModule.java:97) at sun.reflect.GeneratedMethodAccessor286.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.jboss.mx.interceptor.ReflectedDispatcher.invoke(ReflectedDispatcher.java:157) at org.jboss.mx.server.Invocation.dispatch(Invocation.java:96) at org.jboss.mx.server.Invocation.invoke(Invocation.java:88) at org.jboss.mx.server.AbstractMBeanInvoker.invoke(AbstractMBeanInvoker.java:264) at org.jboss.mx.server.MBeanServerImpl.invoke(MBeanServerImpl.java:668) at org.jboss.system.microcontainer.ServiceProxy.invoke(ServiceProxy.java:206) at $Proxy38.start(Unknown Source) at org.jboss.system.microcontainer.StartStopLifecycleAction.installAction(StartStopLifecycleAction.java:42) at org.jboss.system.microcontainer.StartStopLifecycleAction.installAction(StartStopLifecycleAction.java:37) at org.jboss.dependency.plugins.action.SimpleControllerContextAction.simpleInstallAction(SimpleControllerContextAction.java:62) at org.jboss.dependency.plugins.action.AccessControllerContextAction.install(AccessControllerContextAction.java:71) at org.jboss.dependency.plugins.AbstractControllerContextActions.install(AbstractControllerContextActions.java:51) at org.jboss.dependency.plugins.AbstractControllerContext.install(AbstractControllerContext.java:348) at org.jboss.system.microcontainer.ServiceControllerContext.install(ServiceControllerContext.java:286) at org.jboss.dependency.plugins.AbstractController.install(AbstractController.java:1631) at org.jboss.dependency.plugins.AbstractController.incrementState(AbstractController.java:934) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:1082) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:984) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:822) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:553) at org.jboss.system.ServiceController.doChange(ServiceController.java:688) at org.jboss.system.ServiceController.start(ServiceController.java:460) at org.jboss.system.deployers.ServiceDeployer.start(ServiceDeployer.java:163) at org.jboss.system.deployers.ServiceDeployer.deploy(ServiceDeployer.java:99) at org.jboss.system.deployers.ServiceDeployer.deploy(ServiceDeployer.java:46) at org.jboss.deployers.spi.deployer.helpers.AbstractSimpleRealDeployer.internalDeploy(AbstractSimpleRealDeployer.java:62) at org.jboss.deployers.spi.deployer.helpers.AbstractRealDeployer.deploy(AbstractRealDeployer.java:50) at org.jboss.deployers.plugins.deployers.DeployerWrapper.deploy(DeployerWrapper.java:171) at org.jboss.deployers.plugins.deployers.DeployersImpl.doDeploy(DeployersImpl.java:1439) at org.jboss.deployers.plugins.deployers.DeployersImpl.doInstallParentFirst(DeployersImpl.java:1157) at org.jboss.deployers.plugins.deployers.DeployersImpl.doInstallParentFirst(DeployersImpl.java:1178) at org.jboss.deployers.plugins.deployers.DeployersImpl.install(DeployersImpl.java:1098) at org.jboss.dependency.plugins.AbstractControllerContext.install(AbstractControllerContext.java:348) at org.jboss.dependency.plugins.AbstractController.install(AbstractController.java:1631) at org.jboss.dependency.plugins.AbstractController.incrementState(AbstractController.java:934) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:1082) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:984) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:822) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:553) at org.jboss.deployers.plugins.deployers.DeployersImpl.process(DeployersImpl.java:781) at org.jboss.deployers.plugins.main.MainDeployerImpl.process(MainDeployerImpl.java:702) at org.jboss.system.server.profileservice.repository.MainDeployerAdapter.process(MainDeployerAdapter.java:117) at org.jboss.system.server.profileservice.hotdeploy.HDScanner.scan(HDScanner.java:362) at org.jboss.system.server.profileservice.hotdeploy.HDScanner.run(HDScanner.java:255) at java.util.concurrent.Executors$RunnableAdapter.call(Executors.java:441) at java.util.concurrent.FutureTask$Sync.innerRunAndReset(FutureTask.java:317) at java.util.concurrent.FutureTask.runAndReset(FutureTask.java:150) at java.util.concurrent.ScheduledThreadPoolExecutor$ScheduledFutureTask.access$101(ScheduledThreadPoolExecutor.java:98) at java.util.concurrent.ScheduledThreadPoolExecutor$ScheduledFutureTask.runPeriodic(ScheduledThreadPoolExecutor.java:181) at java.util.concurrent.ScheduledThreadPoolExecutor$ScheduledFutureTask.run(ScheduledThreadPoolExecutor.java:205) at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:885) at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:907) at java.lang.Thread.run(Thread.java:619) 03:16:24,629 INFO [2-facelets-portlet]] Marking servlet FacesServlet as unavailable 03:16:24,630 ERROR [2-facelets-portlet]] Servlet /richfaces-sun-jsf1.2-facelets-portlet threw load() exception javax.servlet.UnavailableException: Initialization of the JSF runtime either failed or did not occurr. Review the server''s log for details. at javax.faces.webapp.FacesServlet.init(FacesServlet.java:172) at org.apache.catalina.core.StandardWrapper.loadServlet(StandardWrapper.java:1048) at org.apache.catalina.core.StandardWrapper.load(StandardWrapper.java:950) at org.apache.catalina.core.StandardContext.loadOnStartup(StandardContext.java:4122) at org.apache.catalina.core.StandardContext.start(StandardContext.java:4421) at org.jboss.web.tomcat.service.deployers.TomcatDeployment.performDeployInternal(TomcatDeployment.java:310) at org.jboss.web.tomcat.service.deployers.TomcatDeployment.performDeploy(TomcatDeployment.java:142) at org.jboss.web.deployers.AbstractWarDeployment.start(AbstractWarDeployment.java:461) at org.jboss.web.deployers.WebModule.startModule(WebModule.java:118) at org.jboss.web.deployers.WebModule.start(WebModule.java:97) at sun.reflect.GeneratedMethodAccessor286.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.jboss.mx.interceptor.ReflectedDispatcher.invoke(ReflectedDispatcher.java:157) at org.jboss.mx.server.Invocation.dispatch(Invocation.java:96) at org.jboss.mx.server.Invocation.invoke(Invocation.java:88) at org.jboss.mx.server.AbstractMBeanInvoker.invoke(AbstractMBeanInvoker.java:264) at org.jboss.mx.server.MBeanServerImpl.invoke(MBeanServerImpl.java:668) at org.jboss.system.microcontainer.ServiceProxy.invoke(ServiceProxy.java:206) at $Proxy38.start(Unknown Source) at org.jboss.system.microcontainer.StartStopLifecycleAction.installAction(StartStopLifecycleAction.java:42) at org.jboss.system.microcontainer.StartStopLifecycleAction.installAction(StartStopLifecycleAction.java:37) at org.jboss.dependency.plugins.action.SimpleControllerContextAction.simpleInstallAction(SimpleControllerContextAction.java:62) at org.jboss.dependency.plugins.action.AccessControllerContextAction.install(AccessControllerContextAction.java:71) at org.jboss.dependency.plugins.AbstractControllerContextActions.install(AbstractControllerContextActions.java:51) at org.jboss.dependency.plugins.AbstractControllerContext.install(AbstractControllerContext.java:348) at org.jboss.system.microcontainer.ServiceControllerContext.install(ServiceControllerContext.java:286) at org.jboss.dependency.plugins.AbstractController.install(AbstractController.java:1631) at org.jboss.dependency.plugins.AbstractController.incrementState(AbstractController.java:934) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:1082) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:984) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:822) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:553) at org.jboss.system.ServiceController.doChange(ServiceController.java:688) at org.jboss.system.ServiceController.start(ServiceController.java:460) at org.jboss.system.deployers.ServiceDeployer.start(ServiceDeployer.java:163) at org.jboss.system.deployers.ServiceDeployer.deploy(ServiceDeployer.java:99) at org.jboss.system.deployers.ServiceDeployer.deploy(ServiceDeployer.java:46) at org.jboss.deployers.spi.deployer.helpers.AbstractSimpleRealDeployer.internalDeploy(AbstractSimpleRealDeployer.java:62) at org.jboss.deployers.spi.deployer.helpers.AbstractRealDeployer.deploy(AbstractRealDeployer.java:50) at org.jboss.deployers.plugins.deployers.DeployerWrapper.deploy(DeployerWrapper.java:171) at org.jboss.deployers.plugins.deployers.DeployersImpl.doDeploy(DeployersImpl.java:1439) at org.jboss.deployers.plugins.deployers.DeployersImpl.doInstallParentFirst(DeployersImpl.java:1157) at org.jboss.deployers.plugins.deployers.DeployersImpl.doInstallParentFirst(DeployersImpl.java:1178) at org.jboss.deployers.plugins.deployers.DeployersImpl.install(DeployersImpl.java:1098) at org.jboss.dependency.plugins.AbstractControllerContext.install(AbstractControllerContext.java:348) at org.jboss.dependency.plugins.AbstractController.install(AbstractController.java:1631) at org.jboss.dependency.plugins.AbstractController.incrementState(AbstractController.java:934) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:1082) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:984) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:822) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:553) at org.jboss.deployers.plugins.deployers.DeployersImpl.process(DeployersImpl.java:781) at org.jboss.deployers.plugins.main.MainDeployerImpl.process(MainDeployerImpl.java:702) at org.jboss.system.server.profileservice.repository.MainDeployerAdapter.process(MainDeployerAdapter.java:117) at org.jboss.system.server.profileservice.hotdeploy.HDScanner.scan(HDScanner.java:362) at org.jboss.system.server.profileservice.hotdeploy.HDScanner.run(HDScanner.java:255) at java.util.concurrent.Executors$RunnableAdapter.call(Executors.java:441) at java.util.concurrent.FutureTask$Sync.innerRunAndReset(FutureTask.java:317) at java.util.concurrent.FutureTask.runAndReset(FutureTask.java:150) at java.util.concurrent.ScheduledThreadPoolExecutor$ScheduledFutureTask.access$101(ScheduledThreadPoolExecutor.java:98) at java.util.concurrent.ScheduledThreadPoolExecutor$ScheduledFutureTask.runPeriodic(ScheduledThreadPoolExecutor.java:181) at java.util.concurrent.ScheduledThreadPoolExecutor$ScheduledFutureTask.run(ScheduledThreadPoolExecutor.java:205) at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:885) at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:907) at java.lang.Thread.run(Thread.java:619)

    Read the article

  • Cisco 881 losing NAT NVI translation config after reload

    - by MasterRoot24
    This is a weird one, so I'll try to explain in as much detail as I can so I'm giving the whole picture. As I've mentioned in my other questions, I'm in the process of setting up a new Cisco 881 as my WAN router and NAT firewall. I'm facing an issue where NAT NVI rules that I have configured are not enabled after a reload of the router, regardless of the fact that they are present in the startup-config. In order to clarify this a little, here's the relevant section of my current running-config: Router1#show running-config | include nat source ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ip nat source static tcp 192.168.1.x 80 interface FastEthernet4 80 ip nat source static tcp 192.168.1.x 443 interface FastEthernet4 443 ip nat source static tcp 192.168.1.x 25 interface FastEthernet4 25 ip nat source static tcp 192.168.1.x 587 interface FastEthernet4 587 ip nat source static tcp 192.168.1.x 143 interface FastEthernet4 143 ip nat source static tcp 192.168.1.x 993 interface FastEthernet4 993 ...and here's the mappings 'in action': Router1#show ip nat nvi translations | include --- tcp <WAN IP>:25 192.168.1.x:25 --- --- tcp <WAN IP>:80 192.168.1.x:80 --- --- tcp <WAN IP>:143 192.168.1.x:143 --- --- tcp <WAN IP>:443 192.168.1.x:443 --- --- tcp <WAN IP>:587 192.168.1.x:587 --- --- tcp <WAN IP>:993 192.168.1.x:993 --- --- tcp <WAN IP>:1723 192.168.1.x:1723 --- --- ...and here's proof that the mappings are saved to startup-config: Router1#show startup-config | include nat source ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ip nat source static tcp 192.168.1.x 80 interface FastEthernet4 80 ip nat source static tcp 192.168.1.x 443 interface FastEthernet4 443 ip nat source static tcp 192.168.1.x 25 interface FastEthernet4 25 ip nat source static tcp 192.168.1.x 587 interface FastEthernet4 587 ip nat source static tcp 192.168.1.x 143 interface FastEthernet4 143 ip nat source static tcp 192.168.1.x 993 interface FastEthernet4 993 However, look what happens after a reload of the router: Router1#reload Proceed with reload? [confirm]Connection to router closed by remote host. Connection to router closed. $ ssh joe@router Password: Authorized Access only Router1>en Password: Router1#show ip nat nvi translations | include --- Router1# Router1#show ip nat translations | include --- tcp 188.222.181.173:25 192.168.1.2:25 --- --- tcp 188.222.181.173:80 192.168.1.2:80 --- --- tcp 188.222.181.173:143 192.168.1.2:143 --- --- tcp 188.222.181.173:443 192.168.1.2:443 --- --- tcp 188.222.181.173:587 192.168.1.2:587 --- --- tcp 188.222.181.173:993 192.168.1.2:993 --- --- tcp 188.222.181.173:1723 192.168.1.2:1723 --- --- Router1# Here's proof that the running config should have the mappings setup as NVI: Router1#show running-config | include nat source ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.2 1723 interface FastEthernet4 1723 ip nat source static tcp 192.168.1.2 80 interface FastEthernet4 80 ip nat source static tcp 192.168.1.2 443 interface FastEthernet4 443 ip nat source static tcp 192.168.1.2 25 interface FastEthernet4 25 ip nat source static tcp 192.168.1.2 587 interface FastEthernet4 587 ip nat source static tcp 192.168.1.2 143 interface FastEthernet4 143 ip nat source static tcp 192.168.1.2 993 interface FastEthernet4 993 At this point, the mappings are not working (inbound connections from WAN on the HTTP/IMAP fail). I presume that this is because my interfaces are using ip nat enable for use with NVI mappings, instead of ip nat inside/outside. So, I re-apply the mappings: Router1#configure ter Router1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router1(config)#ip nat source static tcp 192.168.1.2 1723 interface FastEthernet4 1723 Router1(config)#ip nat source static tcp 192.168.1.2 80 interface FastEthernet4 80 Router1(config)#ip nat source static tcp 192.168.1.2 443 interface FastEthernet4 443 Router1(config)#ip nat source static tcp 192.168.1.2 25 interface FastEthernet4 25 Router1(config)#ip nat source static tcp 192.168.1.2 587 interface FastEthernet4 587 Router1(config)#ip nat source static tcp 192.168.1.2 143 interface FastEthernet4 143 Router1(config)#ip nat source static tcp 192.168.1.2 993 interface FastEthernet4 993 Router1(config)#end ... then they show up correctly: Router1#show ip nat nvi translations | include --- tcp 188.222.181.173:25 192.168.1.2:25 --- --- tcp 188.222.181.173:80 192.168.1.2:80 --- --- tcp 188.222.181.173:143 192.168.1.2:143 --- --- tcp 188.222.181.173:443 192.168.1.2:443 --- --- tcp 188.222.181.173:587 192.168.1.2:587 --- --- tcp 188.222.181.173:993 192.168.1.2:993 --- --- tcp 188.222.181.173:1723 192.168.1.2:1723 --- --- Router1# Router1#show ip nat translations | include --- Router1# ... furthermore, now from both WAN and LAN, the services mapped above now work until the next reload. All of the above is required every time I have to reload the router (which is all too often at the moment :-( ). Here's my full current config: ! ! Last configuration change at 20:20:15 UTC Tue Dec 11 2012 by xxx version 15.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname xxx ! boot-start-marker boot-end-marker ! ! enable secret 4 xxxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 xxx quit ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! ip domain list dmz.xxx.local ip domain list xxx.local ip domain name dmz.xxx.local ip name-server 192.168.1.x ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn xxx ! ! username admin privilege 15 secret 4 xxx username joe secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp ip access-group 101 in ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.x 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.x 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ! ! ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ! ! access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.1.0 0.0.0.255 access-list 101 permit udp 193.x.x.0 0.0.0.255 any eq 5060 access-list 101 deny udp any any eq 5060 access-list 101 permit ip any any ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 exec-timeout 15 0 login authentication local_auth line aux 0 exec-timeout 15 0 login authentication local_auth line vty 0 4 access-class 2 in login authentication local_auth length 0 transport input all ! ! end I'd appreciate it greatly if anyone can help me find out why these mappings are not setup correctly using the saved config after a reload.

    Read the article

  • Recovering a VHD after resizing it using VBoxManage

    - by tjrobinson
    I am using VirtualBox 4.1.18 and had a virtual machine running Windows 8 RC with a single VHD, which was initially sized at 25GB (too small!). After installing the OS and some applications I ran out of disk space so shut down the guest and then used this command to resize the VHD to 80GB: C:\Program Files\Oracle\VirtualBox> .\VBoxManage.exe modifyhd "D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vhd" --resize 81920 0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100% C:\Program Files\Oracle\VirtualBox> .\VBoxManage.exe showhdinfo "D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vhd" UUID: 03fb26e7-d8bb-49b5-8cc2-1dc350750e64 Accessible: yes Logical size: 81920 MBytes Current size on disk: 24954 MBytes Type: normal (base) Storage format: VHD Format variant: dynamic default In use by VMs: Windows 8 RC (UUID: a6e6aa57-2d3a-421b-8042-7aae566e3e0b) Location: D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vhd So far so good. However, when I started the guest up again I got the dreaded: Fatal: No bootable medium found! system halted If I boot into GParted it shows a single 80GB drive as "unallocated". The option to scan for and attempt to repair a filesystem doesn't find anything. I also tried cloning the VHD into a VDI file, just in case that magically fixed it: C:\Program Files\Oracle\VirtualBox> .\VBoxManage.exe clonehd "D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vhd" "D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vdi" --format VDI 0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100% Clone hard disk created in format 'VDI'. UUID: baf0c2c4-362f-4f6c-846a-37bb1ffc027b C:\Program Files\Oracle\VirtualBox> .\VBoxManage.exe showhdinfo "D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vdi" UUID: baf0c2c4-362f-4f6c-846a-37bb1ffc027b Accessible: yes Logical size: 81920 MBytes Current size on disk: 24798 MBytes Type: normal (base) Storage format: VDI Format variant: dynamic default In use by VMs: Windows 8 RC (UUID: a6e6aa57-2d3a-421b-8042-7aae566e3e0b) Location: D:\VirtualBox VMs\Windows 8 RC\Windows 8 RC.vdi Is there anything else I could try to recover the drive? No, I don't have a backup :( My host OS is Windows 7 64-bit.

    Read the article

< Previous Page | 254 255 256 257 258 259 260 261 262 263 264 265  | Next Page >