Search Results

Search found 7502 results on 301 pages for 'defective hardware'.

Page 259/301 | < Previous Page | 255 256 257 258 259 260 261 262 263 264 265 266  | Next Page >

  • How to minimize the risk of employees spreading critical information?

    - by Industrial
    Hi everyone, What's common sense when it comes to minimising the risk of employees spreading critical information to rivalling companies? As of today, it's clear that not even the US government and military can be sure that their data stays safely within their doors. Thereby I understand that my question probably instead should be written as "What is common sense to make it harder for employees to spread business critical information?" If anyone would want to spread information, they will find a way. That's the way life work and always has. If we make the scenario a bit more realistic by narrowing our workforce by assuming we only have regular John Does onboard and not Linux-loving sysadmins , what should be good precautions to at least make it harder for the employees to send business-critical information to the competition? As far as I can tell, there's a few obvious solutions that clearly has both pros and cons: Block services such as Dropbox and similar, preventing anyone to send gigabytes of data through the wire. Ensure that only files below a set size can be sent as email (?) Setup VLANs between departments to make it harder for kleptomaniacs and curious people to snoop around. Plug all removable media units - CD/DVD, Floppy drives and USB Make sure that no configurations to hardware can be made (?) Monitor network traffic for non-linear events (how?) What is realistic to do in a real world? How does big companies handle this? Sure, we can take the former employer to court and sue, but by then the damage has already been caused... Thanks a lot

    Read the article

  • CentOS Installation on a Cisco MCS 7800

    - by William
    Hello, I'm having some problems installing CentOS 5.5 Final (i386) Onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up ans gives you the option on how to boot into the DVD, Ill press enter to go into the graphical installer. The Screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours.) I then booted into it again and tried using Linux Text thinking it was a problem with graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point i think its a hardware problem. The Server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) Configured for RAID 0. ( Also there is a option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. ================Edit================== ooshro, typing "text" doesn't change a thing. still stuck at the blinking cursor. I looked it up and its really the same thing as typing "linux text", which as stated in the first part of my question, i've already done.

    Read the article

  • How can I remove all drivers and other files related to a USB Mass Storage device?

    - by Bob
    I have a flash drive here that does not work on one OS on computer - let's call it the desktop Windows 7. It works fine on another computer - laptop Windows 7. It also works fine on Windows 8 on the same desktop computer. Other flash drives work fine under desktop Windows 7. So not a hardware issue, not a generic USB Mass Storage driver issue. It's something specific to this drive. On desktop Windows 7, I can connect the drive but no volume comes up under Windows Explorer. Ditto for Disk Management. With diskpart, loading hangs until I unplug the drive, if I replug it and try list disk it hangs again. If I unplug the drive at this point, list disk prints out all attached drives - including the just removed flash drive. The drive consistently appears under Device Manager, but uninstalling the drivers, restarting and reinstalling the drivers (by inserting the drive) only works for the first insertion. After that it fails again. I get the feeling that the driver files are not actually removed, and are corrupted, meaning every reinstall it's the same corrupted drivers being installed. Is there any way to remove these drivers completely? Or perhaps some other setting Windows 7 retains? Formatting the drive through another computer/OS does not help. I've also tried a complete wipe and rebuild of the MBR and single partition. The allocation unit size makes no difference; neither does a NTFS format. This is a relatively small matter, and I would not like to reinstall the entire OS!

    Read the article

  • Distributed storage and computing

    - by Tim van Elteren
    Dear Serverfault community, After researching a number of distributed file systems for deployment in a production environment with the main purpose of performing both batch and real-time distributed computing I've identified the following list as potential candidates, mainly on maturity, license and support: Ceph Lustre GlusterFS HDFS FhGFS MooseFS XtreemFS The key properties that our system should exhibit: an open source, liberally licensed, yet production ready, e.g. a mature, reliable, community and commercially supported solution; ability to run on commodity hardware, preferably be designed for it; provide high availability of the data with the most focus on reads; high scalability, so operation over multiple data centres, possibly on a global scale; removal of single points of failure with the use of replication and distribution of (meta-)data, e.g. provide fault-tolerance. The sensitivity points that were identified, and resulted in the following questions, are: transparency to the processing layer / application with respect to data locality, e.g. know where data is physically located on a server level, mainly for resource allocation and fast processing, high performance, how can this be accomplished? Do you from experience know what solutions provide this transparency and to what extent? posix compliance, or conformance, is mentioned on the wiki pages of most of the above listed solutions. The question here mainly is, how relevant is support for the posix standard? Hadoop for example isn't posix compliant by design, what are the pro's and con's? what about the difference between synchronous and asynchronous opeartion of a distributed file system. Though a synchronous distributed file system has the preference because of reliability it also imposes certain limitations with respect to scalability. What would be, from your expertise, the way to go on this? I'm looking forward to your replies. Thanks in advance! :) With kind regards, Tim van Elteren

    Read the article

  • Anonymous Login attemps from IPs all over Asia, how do I stop them from being able to do this?

    - by Ryan
    We had a successful hack attempt from Russia and one of our servers was used as a staging ground for further attacks, actually somehow they managed to get access to a Windows account called 'services'. I took that server offline as it was our SMTP server and no longer need it (3rd party system in place now). Now some of our other servers are having these ANONYMOUS LOGIN attempts in the Event Viewer that have IP addresses coming from China, Romania, Italy (I guess there's some Europe in there too)... I don't know what these people want but they just keep hitting the server. How can I prevent this? I don't want our servers compromised again, last time our host took our entire hardware node off of the network because it was attacking other systems, causing our services to go down which is really bad. How can I prevent these strange IP addresses from trying to access my servers? They are Windows Server 2003 R2 Enterprise 'containers' (virtual machines) running on a Parallels Virtuozzo HW node, if that makes a difference. I can configure each machine individually as if it were it's own server of course... UPDATE: New login attempts still happening, now these ones are tracing back to Ukraine... WTF.. here is the Event: Successful Network Logon: User Name: Domain: Logon ID: (0x0,0xB4FEB30C) Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: REANIMAT-328817 Logon GUID: - Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: 94.179.189.117 Source Port: 0 For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Here is one from France I found too: Event Type: Success Audit Event Source: Security Event Category: Logon/Logoff Event ID: 540 Date: 1/20/2011 Time: 11:09:50 AM User: NT AUTHORITY\ANONYMOUS LOGON Computer: QA Description: Successful Network Logon: User Name: Domain: Logon ID: (0x0,0xB35D8539) Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: COMPUTER Logon GUID: - Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: 82.238.39.154 Source Port: 0 For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

    Read the article

  • Connect two networks

    - by Meek Barrios
    Connecting two different offices with a wireless link and linux boxes. Hardware: 2 CISCO RV42, 2 Dual Homed Linux Boxes running debian, 2 2Wire and 2 AirMax 5 Configuration is: Office A LAN A (10.1.1.0/24) -> RV42 A (WAN1 - 10.1.1.254) -> 2Wire A (Internet) LINUX A ( ETH0 (LAN) 10.1.1.253, ETH1 (LINK) (10.1.3.3) Wireless Link --- AirMax A <-> AirMax B connected as Wireless Bridge Office B LAN B (10.1.2.0/24) -> RV42 B (WAN1 - 10.1.2.254) -> 2Wire B (Internet) LINUX B ( ETH0 (LAN) 10.1.2.253 -> ETH1 (LINK) (10.1.3.4) Network configuration is: LAN A - Default Gateway 10.1.1.254 RV42 A - Static Route 10.1.3.0/24 on 10.1.1.253 Static Route 10.1.2.0/24 on 10.1.1.253 Default on 192.168.1.1 (WAN1 Internet Access) Linux A - ETH0 10.1.1.253 netmask 255.255.255.0 gw 10.1.1.254 ETH1 10.1.3.3 netmask 255.255.255.0 gw 10.1.3.1 AIRMAX A - 10.1.3.1 netmask 255.255.255.0 gw 10.1.3.1 LAN B - Default Gateway 10.1.2.254 RV42 B - Static Route 10.1.3.0/24 on 10.1.2.253 Static Route 10.1.1.0/24 on 10.1.2.253 Default on 192.168.1.1 (WAN1 Internet Access) Linux B - ETH0 10.1.2.253 netmask 255.255.255.0 gw 10.1.2.254 ETH1 10.1.3.4 netmask 255.255.255.0 gw 10.1.3.2 AIRMAX B - 10.1.3.2 netmask 255.255.255.0 gw 10.1.3.2 Both linux have ip_forward set to 1 and the following on the iptables: iptables -F iptables -X iptables -P FORWARD ACCEPT iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT I can ping from Linux B any ip on 10.1.1.0/24 segment and on linux A any ip on 10.1.2.0/24 segment however I cannot connect to HTTP or FTP on those machines. From LAN A I cannot see any other network. I'm looking for some advice for this configuration or a better solution. Regards

    Read the article

  • Wired to wireless bridge in Linux

    - by adrianmcmenamin
    I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

    Read the article

  • Disable or remove filter driver for single HID device

    - by snoopen
    Running Windows XP in a corporate setting here. I have an issue where a filter driver is interfering with the functionality of different USB HIDs. For example graphics tablets do not respond while the filter driver is in place. I've also had the issue with foot pedals used with transcription software. My question is really two fold: A) what makes Windows use a filter driver on one HID but not another? B) when a filter driver is causing conflicts how can I disable it on the affected devices? Background I've previously narrowed down the issue to the filter driver by uninstalling the software (Funk Proxy Host) responsible for the filter driver. The software is a type of RDP we use here at work. (I might have even booted into safe mode and renamed the file, I forget). I believe the filter driver is present to disable or modify the use of the local keyboard and mouse while admin staff are assisting users. Either way I don't have the authority to just go uninstalling this software. As far as I can tell the software versions are the same, however I'm not sure if the device driver definitions are all the same as I don't know where these things would be located. To check for the presence of the filter driver I locate the hardware device in Device Manager, click Properties Driver tab Driver Details.... It shows up as ph32ihid.sys. Even though all machines are meant to have the same SOE and do have Funk Proxy Host installed I don't always have issues with the same HIDs. A few machines here the foot pedals without any issues. I've not had any machines work with the graphics tablet without uninstalling Funk software. Driver details I've just read up a bit more about filter drivers and found the drivers description in the registry under "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\ProxyHostHIDFilter" There it's called "Kernel-mode HID filter driver for the Proxy Host". Presumably I could also disable it here but that would be system wide which is probably not desirable?

    Read the article

  • All network devices freezing when Airport Extreme Base Station is connected. Any ideas?

    - by Jon
    I've been troubleshooting this issue for a while, and through a series of events have it narrowed down to my airport extreme base station. I like this router, since I'm able to connect to IPV6 sites without any insane configuration (my alternate router is too old and doesn't support v6). My question is: Has anyone else had this issue, if so how is it resolved? If not, can you recommend a good IPv6 router? Here is how I came to the conclusion that it is the router: Devices: XBOX 360, HTC Incredible, Home-Built machine running FreeBSD, Home-Built machine running Ubuntu 10.04. 1.) Noticed freezing on Ubuntu Box. 2.) Noticed freezing on XBOX360 3.) Noticed freezing on HTC Incredible (only when connected to my network wirelessly). The above all happened at random times throughout the past few weeks. Over the last few days, I was playing XBOX and noticed that the XBOX and Ubuntu machines both froze. I picked up my phone, and it was also frozen. I reset all devices, power-cycled my router, and all was fine again. About two hours later, it happened again (I was playing Forza III, the XBOX froze; I went to the Ubuntu box and it was frozen; unfortunately, the HTC phone was not connected wirelessly, and the FreeBSD box was turned off). I can't even begin to imaging what a router could be doing to freeze devices with such differing hardware/software/OS, and I feel absurd for coming to this conclusion, but I have nothing else. I hooked up my archaic Netgear router, and have had no problems since. :(

    Read the article

  • How to monitor bandwidth use of each device on wifi network

    - by GWLlosa
    I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

    Read the article

  • Bad performance with Linux software RAID5 and LUKS encryption

    - by Philipp Wendler
    I have set up a Linux software RAID5 on three hard drives and want to encrypt it with cryptsetup/LUKS. My tests showed that the encryption leads to a massive performance decrease that I cannot explain. The RAID5 is able to write 187 MB/s [1] without encryption. With encryption on top of it, write speed is down to about 40 MB/s. The RAID has a chunk size of 512K and a write intent bitmap. I used -c aes-xts-plain -s 512 --align-payload=2048 as the parameters for cryptsetup luksFormat, so the payload should be aligned to 2048 blocks of 512 bytes (i.e., 1MB). cryptsetup luksDump shows a payload offset of 4096. So I think the alignment is correct and fits to the RAID chunk size. The CPU is not the bottleneck, as it has hardware support for AES (aesni_intel). If I write on another drive (an SSD with LVM) that is also encrypted, I do have a write speed of 150 MB/s. top shows that the CPU usage is indeed very low, only the RAID5 xor takes 14%. I also tried putting a filesystem (ext4) directly on the unencrypted RAID so see if the layering is problem. The filesystem decreases the performance a little bit as expected, but by far not that much (write speed varying, but 100 MB/s). Summary: Disks + RAID5: good Disks + RAID5 + ext4: good Disks + RAID5 + encryption: bad SSD + encryption + LVM + ext4: good The read performance is not affected by the encryption, it is 207 MB/s without and 205 MB/s with encryption (also showing that CPU power is not the problem). What can I do to improve the write performance of the encrypted RAID? [1] All speed measurements were done with several runs of dd if=/dev/zero of=DEV bs=100M count=100 (i.e., writing 10G in blocks of 100M). Edit: If this helps: I'm using Ubuntu 11.04 64bit with Linux 2.6.38. Edit2: The performance stays approximately the same if I pass a block size of 4KB, 1MB or 10MB to dd.

    Read the article

  • Recommended Smartphone for Reading PDFs [closed]

    - by mika
    This is as much a software than a hardware question. I use a lot of public transport and perhaps the best way to spend your time there is to read while listening to music. Currently I use Nokia E90 and Adobe Reader LE 2.5 (full version). I was wondering if there are any better alternatives? Requirements: at least 640px wide screen, preferably 800px physical size of the LCD display matters, it should be large, but the phone itself should be as small as possible. This favors touchscreen models PDF reader should be of high quality. It should render most PDFs correctly. Other important features include: full screen mode, keyboard controls for Page Down and page change, multiple zoom levels to adjust to the screen, opening recent documents at the last page read Downsides of E90 + Adobe Reader LE Phone is large compared to the display It is hard to read the display at sunlight Adobe Reader crashes the phone regularly, zoom could have more levels, doesn't remember last page EDIT: Switched to iPhone and GoodReader. Smaller physical screen width compared to E90 is a disimprovement, but other than that I'm happy. GoodReader is the highest quality smartphone PDF reader I've seen so far.

    Read the article

  • My bios datetime is resetting to 2002, what should I do?

    - by Thierry Lam
    I bought my PC brand new in mid-2006. I'm currently dual booting Win XP 32 bits and Ubuntu Karmic Desktop. Over the last few days, when I boot up my computer, it tells me that my bios time is not set. I now have 2 choices for booting in: Windows first: I can safely get into Windows but the date now shows 2002/01/01 at 00:00. From there, Windows will not sync its time to its servers, I have to manually advance the date myself. I can also advance the date from the bios at startup. Ubuntu first: Since the time date is still set at 2002, the boot system cannot find my linux partition. I can fix that issue by booting to Windows, set the date properly and the linux issue will be fixed automatically. The above two issues can also be fixed if I manually set the bios date/time manually when I turn on my computer. It's annoying to do that every single day since I shut down my PC daily. Am I having an OS issue or a hardware issue? How can I resolve this problem?

    Read the article

  • Two screens hooked to one laptop

    - by mplacona
    Hi, I'm thinking of getting rid of my desktop, and using my (much better) laptop instead. I'm only wondering if I would be able to hook the two screens I have with it, so I'd end up with three screens. I've seen people doing it to desktops, but am not sure the same could be accomplished with a laptop. My laptop is a sony vaio, and it's got both a VGA output, and an HDMI output. It'd be great is I could simply hook two screens to it, and have three independent screens (not mirrored). on my desktop, I have pretty much the same thing, but with an extra DVI port. I connect the DVI to one screen, and the VGA to an older one. Trying to connect anything to the HDMI simply mirrors whatever is on the DVI (I've tried it a long time ago) So I was wondering if with the laptop I'd be able to do it, and end up with three independent screens. I don't know if there's anything else I could be using instead (i.e. any extra hardware), so recommendations are more than welcome. Thanks in advance, Marcos

    Read the article

  • Creating a Jenkins build farm in a hands-off manner?

    - by user183394
    My colleague and I have set up and run Jenkins on a KVM guest running Ubuntu 12.04 with good results for a while now. We are thinking about deploying a cluster of Jenkins CI hosts in master/slave configuration, with the libvirt slave plugin to keep our hardware count low. Our environment is strictly Linux (CentOS, Scientific Linux, Fedora, and Ubuntu). Both of us are competent in setting up large clusters. We typically use tools like cobbler + a configuration management tool (Puppet, Chef, and alike) to set up a large number of machines (physical and/or virtual) hands off (hundreds of nodes in less than an hour typical). We would like to do the same for nodes running Jenkins. But the step by step guide doesn't give us any clues in this regard. I did see a Multi-slave config plugin. But, being used to dealing with hundreds or more machines completely hands-off, clicking the UI for many machines just doesn't feel right. Can someone point to us a reference that talks about how to set up large cluster of Jenkins CI hosts more in the hands-off way?

    Read the article

  • Two screens hooked to one laptop

    - by mplacona
    Hi, I'm thinking of getting rid of my desktop, and using my (much better) laptop instead. I'm only wondering if I would be able to hook the two screens I have with it, so I'd end up with three screens. I've seen people doing it to desktops, but am not sure the same could be accomplished with a laptop. My laptop is a sony vaio, and it's got both a VGA output, and an HDMI output. It'd be great is I could simply hook two screens to it, and have three independent screens (not mirrored). on my desktop, I have pretty much the same thing, but with an extra DVI port. I connect the DVI to one screen, and the VGA to an older one. Trying to connect anything to the HDMI simply mirrors whatever is on the DVI (I've tried it a long time ago) So I was wondering if with the laptop I'd be able to do it, and end up with three independent screens. I don't know if there's anything else I could be using instead (i.e. any extra hardware), so recommendations are more than welcome. Thanks in advance, Marcos

    Read the article

  • Desktop Provisioning for a Small Linux Software Development Team

    - by deakblue
    Goal: Get a small team using a standard development image rather than 4 software devs setting up their own environments. Why: it takes a day or days to install a distro, build-specific libraries, tools like editors and IDEs, mysql, couchdb, java, maven, python, android-sdk, etc. It's a giant PITA that when repeated 4 times by 4 developers (not sys admins) wastes time and generates annoying divergences that crop up later (it-builds-on-my-box syndrome). There's no sharing of productivity, settings, tricks, scripts, set-ups. Some of this is helped by segregating the build systems into headless virtualbox images. This doesn't really address tooling though or the GUI-desktop dev that needs doing. So I see three basic strategies, ghosting, virtualization, and finally creating a kind of in-house linux distro (I guess Google does something like this). The target dev environment is based on Debian OpenBox and must allow a mix of 3rd gen Core i7 notebooks 8GB-minimum to work both single and multihead. Important, the lappies are not the same, but a mix of 2012 macbooks and PCs. So: virtualization: is doing all of your work within a VM, like VirtualBox, practical on this hardware or annoying. ghosting: will laptops from different manufacturers make this impractical. DIY distro: short of scripting a bunch of package installs, I don't know if there's any "distro-maker" that could keep this from being an epic project of scripting package installs. So any advice?

    Read the article

  • Windows XP hanging on login screen

    - by Nathan W
    I have been given two Eee PC 100HA to manage for some people, they are both running the same hardware and XP home but one is having some strange problems with logging on. The main problem is that it hangs at the login screen for ages and sometimes never gets to the desktop. The strange thing is it only seems to do it after the computer has been cold started, but it won't do it if the computer has been restarted. I have made two logs of the start up with process monitor but every time the logger is attached the computer will log in fine. I have also set the computer to blue screen and create a crash dump when you press ctrl scroll twice but when I do it at the hung login it just sits at a black screen and I don't get a crash dump, I have turned off the auto system restart on failure option also. I can usually fix most computer start up and shutdown problems but this one has got me stuffed. Has anyone had the same problems before, or can recommend something that I can try? Cheers.

    Read the article

  • Doesn't VirtualBox 4.0 support drag-drop file copy yet?

    - by Benjamin
    Version 4.0.0 will be new major release. The following major new features were added: -New settings/disk file layout for VM portability; see the manual for more information. -Open Virtualization Format Archive (OVA) support; see the manual for more information. -VMM: support more than 1.5/2 GB guest RAM on 32-bit hosts -Language bindings: uniform Java bindings for both local (COM/XPCOM) and remote (SOAP) -invocation APIs -Chipset: added support for the Intel ICH9 chipset with 3 PCI buses, PCI express and -Message Signaled Interrupts (MSI) -Audio: Intel HD Audio is now available as guest hardware, for better support with modern -guest operating systems (e.g. 64-bit Windows; bug #2785). -GUI: redesigned user interface with guest window preview -GUI: new display mode with downscaled guest display -Resource control: added support for limiting a VM's CPU time and IO bandwidth. -Storage: support asynchronous I/O for iSCSI, VMDK, VHD and Parallels images -Storage: support for resizing VDI and VHD images -Windows Additions: support for automatically updating the Guest Additions (requires -installed Windows Guest Additions 4.0 or later) -Guest Additions: support for copying files into the guest file system What does the last line mean? I thought this is a drag-drop file copy feature like VMWare. I tried that. But I couldn't copy by drag-drop, ctrl-c ctrl-v either. Edit: I mean VBox 4.0 beta, not 3.x The release note is here. Download link is here.

    Read the article

  • Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

    - by Ron Whites
    Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

    Read the article

  • How To Monitor Home Wireless Network Connected Devices Bandwith

    - by GWLlosa
    (Originally posted on SuperUser, not sure if it might be better suited here) I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

    Read the article

  • virtual machines, dual booting and data disks on SSD

    - by stevemarvell
    This is in planning, so if I've got the strategy wrong, please let me know. There are multiple questions here, but I think they all degenerate to the same answers. The hardware is a laptop with a single SSD. I'm trying to not lose the performance of the SSD. I plan a native dual booting Windows (plus cygwin) and Linux machine which is my BYOD and represents the development environment. I keep the codebase on a shared partition (though sometimes this is an external thunderbolt SSD) which can be natively "mounted" by whichever OS is in operation. I boot into one or the other environments depending on the task in hand. Sometime I have to develop with windows tools, but generally, Linux is my preferred development environment. It would be ideal if I could VM the other OS and run either in either. I'm going to assume, because I've not found a sensible VM based solution, that I have get samba involved to share the code partition between VMs. Is this going to blow my SSD performance in the VM? The client also supplies me with a VM for the target environment, usually linux. This is not often suited to development and is used for testing only. I normally keep two copies of this, one as a sandbox and one which I deploy to using the client's preferred method. I keep these VM snapshots on the shared partition. The latter is interacted with over the network and so has no disk sharing requirements. However, it would be useful for the sandbox to be able to "mount" the code base from the natively running OS. Is this samba or nfs again, depending on the native OS? Am I missing a trick which allows this to all work smoothly with all four environments running at once without loosing the SSD performance?

    Read the article

  • clocksource tsc unstable

    - by amorfis
    Ok, now I have real server fault ;) After some time from booting (about one minute) my server hangs. All I can do is hard reset. Then after restart in /var/log/kern.log I can find: Jul 29 22:38:57 leonidas kernel: [ 90.729598] longhaul: Failed to set requested frequency! Jul 29 22:38:57 leonidas kernel: [ 90.731252] longhaul: Enabling "Ignore Revision ID" option. Jul 29 22:38:57 leonidas kernel: [ 91.201461] longhaul: Failed to set requested frequency! Jul 29 22:38:57 leonidas kernel: [ 91.201482] longhaul: Disabling ACPI C3 support. Jul 29 22:38:57 leonidas kernel: [ 91.204230] longhaul: Disabling "Ignore Revision ID" option. Jul 29 22:38:58 leonidas kernel: [ 91.416133] longhaul: Failed to set requested frequency! Jul 29 22:38:58 leonidas kernel: [ 91.416152] longhaul: Enabling "Ignore Revision ID" option. Jul 29 22:38:58 leonidas kernel: [ 91.960048] Clocksource tsc unstable (delta = -105611479 ns) I found some resources on the net, and it said to change clocksource, or disable ACPI. I tried disabling ACPI but it didn't help (but I noticed there was longer time before hanging). I can't change clock to hpet, because my system doesn't have such one. Output of cat /sys/devices/system/clocksource/clocksource0/available_clocksource: acpi_pm jiffies tsc My system is ubuntu server on VIA Epia hardware.

    Read the article

  • SBS DC DNS entries going missing?

    - by Chris W
    I've been looking at a problem on a friends SBS (2003) server where the client PC's aren't able to connect to the server with a variety of errors reported. Checking the server itself the only indicator of an issue is an error 5782: Dynamic registration or deregistration of one or more DNS records failed with the following error: No DNS servers configured for the local system. Running a dcdiag reports that there are no DNS records registered for the DC so I fixed the problem by doing a netdiag /fix after which the dcdiag comes back clean and clients are ok again. It happened a few weeks ago as well and the same fix solved it. What are the possible causes of the DC DNS entries going missing? Is this a config option that needs tweaking or could it be solved by something simple like scheduling the SBS server to re-boot periodically? The only change they can think of that was made near to the time of the first instance of this problem occurring is that RRAS was started up to allow for a VPN connection from a home user. NB - The server is setup with a pair of NICs in a team so the server has a single virtual NIC providing both LAN/WAN connections to it. An external hardware firewall is in use rather than the windows firewall.

    Read the article

  • Automatic o/s reset on a dedicated internet browsing Windows 7 pc.

    - by camelCase
    I have just purchased a new Acer Revo nettop PC for dedicated internet browsing. It will be the only pc on a home network. My original plan was to install one virtual PC for family browsing, another for remote web based server administration and ban browser use from the host Windows 7 o/s. The idea was that I could recover to a fresh VHD image once a week to eliminate any build up of malware inside the browser VMs. However now I am looking for alternative solutions since the Intel Atom cpu does not have hardware VT support which Windows Virtual PC requires. Would it be possible to engineer some type of routine overnight host o/s wipe and recovery? I guess cyber cafes do something like this? The only user data that would need to be retained across a recovery would be browser bookmarks but these could be exported to remote service. Edit 1: I am thinking the o/s reset could be done via some disk image recovery process. Edit 2: Just had a brainwave. Routine browsing could be done via the new Google Chrome O/S. I have just seen a video of the Google Chrome o/s booting off a usb pen drive in seconds.

    Read the article

< Previous Page | 255 256 257 258 259 260 261 262 263 264 265 266  | Next Page >