Search Results

Search found 19000 results on 760 pages for 'boot tool'.

Page 26/760 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

  • Preinstalled Windows 8 and Linux UEFI dual boot on a laptop

    - by itchy355
    I am trying to set up Windows 8 and Arch Linux on a new Sony Vaio E14 with preinstalled windows 8. So far: installed W8 to my new SSD (switched for the original HDD) using Recovery Media shrunk the W8 partition, deleted recovery partition, disabled swap confirmed W8 booting just fine On to Arch: disabled Secure Boot in bios confirmed W8 booting just fine Booted Arch off the CD and installed everything to 4th and 5th partition set up rEFInd for EFIstub kernel bootloader After that it got worse. I was unable to boot anything else than Windows 8 (although I was glad that they at least kept working just fine). Tried: creating EFI\refind\ and putting the .efi there (as per Arch manual overwriting EFI\boot\bootx64.efi overwriting EFI\Microsoft\Boot\bootmgr.efi overwriting EFI\Microsoft\Boot\bootmgfw.efi --- YAY rEFInd shown up! So far, so good. I've kept the whole W8 Boot\ directory in EFI\windows8 and set up a boot menuentry for it; and it booted just fine. But, upon restart, everything was wrong -- 'Operating system not found' instead of any bootloader (refind or w8). Booted back into Arch using the live CD to find out that the EFI partition had erroneous FAT table. fsck.vfat fixed it, and I've found that EFI\Microsoft\Boot was back to it's original state (all refind files deleted and replaced with W8 bootloaders). I've overwritten them again and got back to rEFInd showing up correctly and Arch being perfectly bootable. After that I've tried only renaming EFI\Microsoft\Boot\bootmgfw.efi to bootmgfw.001.efi (then copying refind's .efi to bootmgfw.efi and keeping EVERY OTHER file as it was), but with exactly the same result. Tried marking the GPT EFI partition as read-only, same result. Now I'm kinda out of luck. Arch boots fine, so does W8 but it destroys the EFI partition in the process. Thanks for any ideas, Googling brought me this far and I can't find any better. PS -- windows 8 MAYBE destroys the partition upon shutdown -- when I order a shutdown in W8, it takes unusually long (about half a minute instead of ~5 seconds). So in theory I could solve this by hard-resetting the laptop instead of a normal shutdown, but that's just not nice.

    Read the article

  • Prevent udev / uevents looking up DVD at boot time

    - by Sampo
    Problem: Boot time delay caused by udev. Early after initscripts starts there is message saying waiting for uevents to be processed and causing delay on boot, it seems that udev is looking if there is disc in dvd tray. After udev has found disc, boot process continues normally. Main question: How to prevent udev dvd lookup at boot time? Maybe there is some way to skip some udev related stuff and let boot process continue and then later instruct udev to do stuff that may cause some delay (delay in uevents, but not in main boot process, is acceptable after udev is initially loaded).

    Read the article

  • Cant install windows 7(boot problem)

    - by Vadiklk
    First of all, I cant boot my windows 7. I get a black screen with a cursor up in the left corner. So, I tried using windows 7 installation which I've put on my flash drive. To boot from the drive, I've changed the boot order to boot from the drive first. It boots but does not find any HDD to install the windows on(which is pretty logic, I dont boot the HDD soon enough for the installer). but if i put the HDD in front of the flash drive in the boot order, it will just try to load windows 7 and i will get the black screen again. I've tried putting the HDD first and clicking f8 a lot. All I've got is an error. Something about some software change. I dunno. Help me please, cant do anything with my laptop till then.

    Read the article

  • Dual boot Windows 8 and Ubuntu?

    - by askvictor
    I've installed Windows 8 on a machine (lenovo x220 laptop) with Ubuntu 12.10 already installed on another disk. I am guessing that Windows 8 has convinced the laptop to switch to UEFI boot (rather than the BIOS boot that was there previously) as the Lenovo splash screen on startup now no longer has the options to interrupt the boot process (e.g. to choose the boot drive). Previously I had Windows 8 on one drive and Ubuntu on the other drive, so could choose my OS through the BIOS rather than through grub or other bootloader but now no longer have that option. How can I get back the option to boot Ubuntu? I would sort of prefer UEFI boot as it seems much faster than BIOS.

    Read the article

  • Ubuntu 10.10 and Windows 7 (TrueCrypt) Multi-boot Problems

    - by Samuel Taylor
    I have now been searching days for a solution but have found nothing. I have Ubuntu 10.10 and Windows 7 with TrueCrypt as a multi-boot. It was working fine for a few weeks until I needed to reinstall Ubuntu. If I have the boot flag on the partition where Windows 7 is install (This is where the boot flags was when working before.), it boots fine in to Windows 7 but when pressing Esc it can't find grub2. If I have the boot flag on the partition where Ubuntu is install, it boots fine in to Ubuntu (by pressing Esc or typing the password) but unable to access Windows. I have tried reinstalling TrueCrypt Boot loader and repairing the header but it have no affect. My Partitions: sda1 - Windows 7 Recovery (GRUB2) sda2 - Windows 7 (TrueCrypt Boot Loader) sda3 - Ubuntu 10.10 (/) sda4 - Extended sda5 - Swap sda6 - Ubuntu (/home) Does anyone have any ideas? Thanks Sam

    Read the article

  • Adding Windows 7 to Fedora 17 Grub Boot Loader

    - by Kyle
    I'm trying to set up a dual-boot situation with my Windows 7 and Fedora 17 partitions and I left the install grub to /boot option on when I was installing Fedora. I would like to be able to add Windows 7 to the grub boot loader, but the advice I've seen online says to modify /boot/grub/grub.conf, but I don't have that file. $ ls /boot/grub/ splash.xpm.gz Has anyone done this? I'm thinking that I'll just need to re-install everything and use the Windows boot loader, but it would be nice to use grub instead.

    Read the article

  • Netbook won't boot after using EasyBCD

    - by TNC
    I have an Asus T91MT netbook on which I used to have Windows 7 Home Premium and Ubuntu 10.10 installed (dual boot). After trying to upgrade to Ubuntu 11.04, Ubuntu is no longer able to boot, so I tried to uninstall Ubuntu completely and then reinstall it. Following these directions, I tried using EasyBCD to bypass the GRUB2 bootloader so that after uninstalling, it would automatically boot into Windows 7. However, after doing the "install BCD" step and restarting, I got the following message: Windows failed to start... File: \Boot\BCD; Status: 0xc0000098; Info: The Windows Boot Configuration Data file does not contain a valid OS entry. I'm currently trying to create a USB stick of the Windows Installation disc but in the mean time, I can only boot from a Ubuntu USB stick. Is there anything I can do from within Ubuntu to fix this? Or does anyone have any other suggestions/solutions?

    Read the article

  • Access boot menu from Windows 8 PC

    - by svnpenn
    I have a computer that came with Windows 8 preinstalled. I want to boot from a CD, in this case Hiren's Boot CD. However Windows 8 doesn't seem to like this. I have tried pressing F8, ESC, F12 and so on. I read online that Windows 8 can boot in 200ms, so that it might not even be possible to boot from a Live CD before Windows loads. I would like to know how to boot from a CD before Windows loads, if possible. If not possible, how to boot from the Live CD after Windows loads.

    Read the article

  • Restore boot sector from a hard disc to another

    - by giang.asl.8
    I have a win7 on my old Seagate HDD. Recently I installed one new SSD and setup win8 on it. So I have a boot table to choose win7 or win8 to startup. Now when I tried to remove the old one (the Seagate), I can't boot into windows any more. I just have a blinking underscore in boot screen, forever ang forever. I guess the reason is that the boot sector, or boot table (or something like that) was installed on the old HDD. So may someone show me how to boot into my win8 without reinstall the old HDD.

    Read the article

  • System unable to boot in normal mode..! need to select recovery mode and than Generic Mode to boot.?

    - by Haresh Veera
    I am using Ubuntu Server 12.04 LTS KDE Mode. Couple of Days back I updated the system using Muon Package manager. After Updating, now when ever I boot the system, It get stuck at starting bluetooth Daemon Ok / Stopping Bluetooth Daemon Fail.and after long wait its get start to GUI Mode, but with no mouse detection. So need to reboot by pressing CTL+ALT+DEL and when I select recovery mode - Boot in Generic -- It boot perfectly. How can I set the same as default, and remove the error boot loader script. I am no expert to linux or Kernel.

    Read the article

  • Slow boot on Ubuntu 12.04, probable cause the network connection

    - by Ravi S Ghosh
    I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

    Read the article

  • Just updated, after reboot my computer won't start up again

    - by Alex
    I have a macbook that I use on occasion which dual boots Ubuntu and OSX (It has rEFIt installed). I turned it on for the first time in a while and it needed a bunch of updates. So I let it run, and restarted it when it asked. When it was booting up, it got stuck at a light blue screen. There was nothing on the screen to indicate that it was doing anything - I figured it just got stuck or something, so I turned it off and back on. (I suspect now it was actually working, but I had no indication that it hadn't just frozen) Now I can't access either OSX or my Ubuntu partition. When I choose ubuntu on the rEFIt menu, it shows "No bootable device -- insert book disk and press key". If I try to start up OSX is looks like it starts loading, but instead of an apple logo there's a crossed out circle icon.

    Read the article

  • Ubuntu boots to terminal on start up

    - by Jules
    For a long time I've been unable to get updates due to a "repositories not found" error. Yesterday someone fixed this for me but after installing 94 days worth of updates my system wanted to restart. It looks like it is booting normally but then it opens a terminal and asks for my login and password. I had tried Ctrl+ Alt +F7 and startx to no avail. Here is everything that appears on screen when I turn the computer on. Ubuntu 10.04.4 LTS box-o-doom tty1 box-o-doom login:julian password: last login: Sun Jul 8 10:28:02 BST tty1 Linux box-o-doom 2.6.32-41-generic-pae #91-Ubuntu SMP Wed Jun 13 12:00:09 UTC 20 12 i686 GNU/Linux Ubuntu 10.04.4 LTS Welcome to Ubuntu! *Documentation: http://help.ubuntu.com julian@box-o-doom:~$_ i then tried dmesg which produced hundreds of lines all very similar to the first line reproduced here [ 9.453119] type=1505 audit1341742405.022:10): operation="profile_replace" pid=743 name="/usr/lib/connman/scripts/dhclient-script" follwed by this at the end [ 9.475880] alloc irq_desc for 27 on node-1 [ 9.475883] alloc kstat_irqs on node-1 [ 9.475890]forcedeth 0000:00:07.0: irq27 for MSI/MSI-X [ 9.760031] hda_code:ALC662 rev1: BIOS auto-probing. [ 10.048095] input:HDA Digital PCBeep as /devices/pci 0000:00:05.o/inp ut/input6 [ 10.862278] ppdev: user-space parallel port driver [ 20.268018] eth0: no IPv6 routers present julian@box-o-doom:~$_ results of startx lots of text scrolls off the screen and i have no way of reading it. but everything i can see is reproduced below current version of pixman: 0.16.4 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version Markers: (--) probed, (**) from config file, (==) defult setting, (++) from command line, (!!) notice, (II) informational. (WW) Warning, (EE) error, (NI) not implemented, (??) unknown. (==) log file: "/var/log/Xorg.0.log", Time: SUn Jul 8 12:02:23 2012 (==) using config file: "/etc/X11/xorg.conf" (==)using config directory: "/usr/lib/X11/xorg.conf.d" FATAL: Module nvidia not found. (EE) NVIDIA: Failed to load the NVIDIA kernal module please check your (EE) NVIDIA: systems kernal log for aditional error messages. (EE) Failed to load module "nvidia" (module specific error, 0) (EE) No drivers available. Fatal server error: no screens found please consult the X.org foundation support at http://wiki.x.org for help please also check the log files at "/var/log/X.org.0.log" for aditional informati on ddxSigGiveUp: Closing log giving up xinit: No such file or directory (errno 2): unable to connect to X server xinit: No suck process (errno 3): server error julian@box-o-doom:~$_

    Read the article

  • How to restore Windows 7 MBR without a CD

    - by Brandon Bertelsen
    I have been playing with Ubuntu for a few weeks now, and I'd like to revert my computer back to it's original - factory - defaults. On the computer I have a recovery partition (it's a netbook). I went through the process of recovery and everything seemed fine. However, when I restart the computer I'm presented with grub rescue > Now, my understanding is that when I installed Ubuntu "side by side" it replaced the MBR or something like it, with GRUB. I've read on a slew of forums, that I need to use a Windows Recovery Disk. Here are my issues: a) I don't have a recovery disk, I have a recovery partition - it's a netbook. b) I don't have an external cd drive. What I do have is a USB key that has about 1gb of space on it. Thanks in advance.

    Read the article

  • Bootable usb stick not boots

    - by Pavaroti Luciano
    i have problem. My bootable usb stick not boots any linux distribution.. it just stop at BIOS, like before turning on OS, but it does nothing. Windows xp/7/8.1 installs boots perfectly. It stopped booting every linux dist. after windows 8.1 installation. Later i deleted windows 8.1 and installed windows 7, and now i want to install ubuntu from usb, but i cant(From disk every linuxOS boots perfectly but not from usb) My computer now is like ~7years old. Specs: CPU: AMD Athlon 64 X2 5000+ Motherboard: GIGABYTE GA-M56S-S3 Video card: Nvidia n210 EDIT: It boots on my other laptop..its bootable, but from this.. NOpe, only windows installs

    Read the article

  • Ubuntu not booting after upgrade to 12.04 from 11.10

    - by ddd
    I upgraded to 12.04 from 11.10 today. After the upgrade, I did the usual reboot of the system and then Ubuntu hangs on Checking battery state..[OK]. I can login to terminal with Ctrl-Alt-F5 and I did startx but it hangs after displaying white images of the desktop icons..there is no menu or any top bar at all. I guess this problem has something to do with Xserver, but I cannot find xorg.conf on my system. How can I get around this problem? Also is there a way I can make a backup of my files through the command line, because the GUI is not showing up at all?

    Read the article

  • Help! Problem dual boot ubuntu windows8 (can't start ubuntu) [duplicate]

    - by a35
    This question already has an answer here: Installing Ubuntu on a Pre-Installed Windows 8 (64-bit) System (UEFI Supported) 5 answers EDIT: I know that there are many topics about dual boot ubuntu windows8, i have read them, my problem is that i cant boot ubuntu neither from HDD nor from live USB. I know about boot repairing, but how can I use it, If i cant boot ubuntu?? I heard about terrible problems with windows 8-linux dual boot, but I really need ubuntu because of school. I read many tutorials how to install ubuntu next to windows8, but despite that a problem accured. Here is what I have done. I have MSI GE60, windows(64bit) is running on mSATA SSD C drive. HDD is divided to two partitions for windows and I left there 50GB for ubuntu. I downloaded ubuntu 12.04.3desktop-amd64(64bit), created bootable USB using Universal USB Installer (recommended on Ubuntu site). I disabled USB legacy support (that Ubuntu could be installed in EFI mode- I was following instructions on Ubuntu site), and also Secure Boot (windows is now angry with me because I turned it off- when I start windows it informs me I should enable that). I inserted USB rebooted computer and chose install ubuntu, divided free 50GB space to swap(2000MB) and rest as ext4 main storage space for ubuntu. Installation passed normally, Ubuntu then asked me to reboot computer. After reboot windows 8 started. Now I can't start ubuntu. When I restart win8 to uefi there is possibility to boot ubuntu, but when I choose it, it crashes. When I choose try ubunfu from connected USB, nothing happend, still dark screed. What is wrong? Can you help me? I am in hurry to do it because of school. Thanks.

    Read the article

  • Dual booting Windows 7 & 8.1, using the Windows 8 Startup Options Menu, when Windows 8.1 is already installed and you want to add Windows 7

    - by Josh
    There are many excellent guides out there that explain how to dual-boot Windows 7 & 8. However, they are written for people starting with a Windows 7 installation and add a Windows 8 installation to separate partition. From what I'm reading, following this procedure will result in Windows 8 installing and configuring the Startup Options Menu with an option to boot Windows 7 & 8. However, in my situation I have a Windows 8.1 machine that I want to install Windows 7 on, and enable dual-boot, where I can use the Startup Options Menu to select the OS to boot. I haven't been able to determine how to do this. From everything I've been able to find, it looks like if I install Windows 7, it is going to take over the boot loader process, and I won't have access to the Windows 8 "Startup Options Menu." This answer suggests I boot to VHD, but notes a drawback: You can't do this if the C:\drive is encrypted using ANY encryption shceme. Be that BitLocker or 3rd party. The location of the .VHD file you are booting to must reside on an unencrypted volume. Well, that's a bummer, because that's exactly what I wanted to do--I wanted my Windows 7 partition to be encrypted, and my Windows 8 partition to also be encrypted. The idea being that when OS was booted, it was completely locked out from accessing data on the other OS's partition. At this point, I'm thinking my only option is to install Windows 7, and then re-install Windows 8, which will give me the dual-boot option... am I right? Or is there a way to make this work. I'm thinking that I would need to figure out a process like this: Configure the Windows Startup Options Menu with a "blank" entry for Windows 7, pointing to an empty partition Insert the Windows 7 installation media, install Windows 7, and somehow restrict it to that partition (i.e., prevent it from "taking over" from the Startup Options Menu" Is this possible, and if so, how can I accomplish this? My concern is that if I simply install Windows 7 to a separate partition, Windows 7 will take over the entire boot process and I won't be able to get to my Windows 8 installation any more.

    Read the article

  • Use external display from boot on Samsung laptop

    - by OhMrBigshot
    I have a Samsung RV511 laptop, and recently my screen broke. I connected an external screen and it works fine, but only after Windows starts. I want to be able to use the external screen right from boot, in order to set the BIOS to boot from DVD, and to then install a different OS and also format the hard drive. Right now I can only use the screen when Windows loads. What I've tried: I've tried opening up the laptop and disconnecting the display to make it only find the external and use the VGA as default -- didn't work. I've tried using the Fn+key combo in BIOS to connect external display - nothing I've been looking around for ways to change boot sequence without entering BIOS, but it doesn't look like it's possible. Possible solutions? A way to change boot sequence without entering BIOS? Someone with the same brand/similar model to help me blindly keystroke the correct arrows/F5/F6 buttons while in BIOS mode to change boot sequence? A way to force the external display to work from boot, through modifying the internal connections (I have no problem taking the laptop apart if needed, please no soldering though), through BIOS or program? Also, if I change boot sequence without accessing external screen, would the Ubuntu 12.1 installation sequence attempt to use the external screen or would I only be able to use it after Linux is installed and running? I'd really appreciate help, I can't afford to fix the screen for a few months from now, and I'd really like to make my computer come back to decent performance! Thanks in advance!

    Read the article

  • Grub 'Read Error' - Only Loads with LiveCD

    - by Ryan Sharp
    Problem After installing Ubuntu to complete my Windows 7/Ubuntu 12.04 dual-boot setup, Grub just wouldn't load at all unless I boot from the LiveCD. Afterwards, everything works completely normal. However, this workaround isn't a solution and I'd like to be able to boot without the aid of a disc. Fdisk -l Using the fdisk -l command, I am given the following: Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x324971d1 Device Boot Start End Blocks Id System /dev/sda1 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 208896 48957439 24374272 7 HPFS/NTFS/exFAT /dev/sda3 * 48959486 124067839 37554177 5 Extended /dev/sda5 48959488 124067839 37554176 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc0ee6a69 Device Boot Start End Blocks Id System /dev/sdb1 1024208894 1953523711 464657409 5 Extended /dev/sdb3 * 2048 1024206847 512102400 7 HPFS/NTFS/exFAT /dev/sdb5 1024208896 1937897471 456844288 83 Linux /dev/sdb6 1937899520 1953523711 7812096 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x292eee23 Device Boot Start End Blocks Id System /dev/sdc1 2048 625141759 312569856 7 HPFS/NTFS/exFAT Bootinfoscript I've used the BootInfoScript, and received the following output: Boot Info Script 0.61 [1 April 2012] ============================= Boot Info Summary: =============================== => Grub2 (v1.99) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Grub2 (v1.99) is installed in the MBR of /dev/sdb and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Windows is installed in the MBR of /dev/sdc. sda1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /bootmgr /Boot/BCD sda2: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe sda3: __________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: sda5: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.04.1 LTS Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb1: __________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sdb5: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Boot files: sdb6: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: sdb3: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: According to the info in the boot sector, sdb3 starts at sector 200744960. But according to the info from fdisk, sdb3 starts at sector 2048. According to the info in the boot sector, sdb3 has 823461887 sectors, but according to the info from fdisk, it has 1024204799 sectors. Operating System: Boot files: sdc1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 2,048 206,847 204,800 7 NTFS / exFAT / HPFS /dev/sda2 208,896 48,957,439 48,748,544 7 NTFS / exFAT / HPFS /dev/sda3 * 48,959,486 124,067,839 75,108,354 5 Extended /dev/sda5 48,959,488 124,067,839 75,108,352 83 Linux Drive: sdb _____________________________________________________________________ Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdb1 1,024,208,894 1,953,523,711 929,314,818 5 Extended /dev/sdb5 1,024,208,896 1,937,897,471 913,688,576 83 Linux /dev/sdb6 1,937,899,520 1,953,523,711 15,624,192 82 Linux swap / Solaris /dev/sdb3 * 2,048 1,024,206,847 1,024,204,800 7 NTFS / exFAT / HPFS Drive: sdc _____________________________________________________________________ Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdc1 2,048 625,141,759 625,139,712 7 NTFS / exFAT / HPFS "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/sda1 A48056DF8056B80E ntfs System Reserved /dev/sda2 A8C6D6A4C6D671D4 ntfs Windows /dev/sda5 fd71c537-3715-44e1-b1fe-07537e22b3dd ext4 /dev/sdb3 6373D03D0A3747A8 ntfs Steam /dev/sdb5 6f5a6eb3-a932-45aa-893e-045b57708270 ext4 /dev/sdb6 469848c8-867a-41b7-b0e1-b813a43c64af swap /dev/sdc1 725D7B961CF34B1B ntfs backup ================================ Mount points: ================================= Device Mount_Point Type Options /dev/sda5 / ext4 (rw,noatime,nodiratime,discard,errors=remount-ro) /dev/sdb5 /home ext4 (rw) =========================== sda5/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd set locale_dir=($root)/boot/grub/locale set lang=en_GB insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "${linux_gfx_mode}" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.2.0-29-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux /boot/vmlinuz-3.2.0-29-generic root=UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-29-generic } menuentry 'Ubuntu, with Linux 3.2.0-29-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd echo 'Loading Linux 3.2.0-29-generic ...' linux /boot/vmlinuz-3.2.0-29-generic root=UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-29-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root A48056DF8056B80E chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda2)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root A8C6D6A4C6D671D4 chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda5/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda5 during installation UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd / ext4 noatime,nodiratime,discard,errors=remount-ro 0 1 # /home was on /dev/sdb5 during installation UUID=6f5a6eb3-a932-45aa-893e-045b57708270 /home ext4 defaults 0 2 # swap was on /dev/sdb6 during installation UUID=469848c8-867a-41b7-b0e1-b813a43c64af none swap sw 0 0 tmpfs /tmp tmpfs defaults,noatime,mode=1777 0 0 -------------------------------------------------------------------------------- =================== sda5: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) = boot/grub/core.img 1 = boot/grub/grub.cfg 1 = boot/initrd.img-3.2.0-29-generic 2 = boot/vmlinuz-3.2.0-29-generic 1 = initrd.img 2 = vmlinuz 1 ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown BootLoader on sda3 00000000 63 6f 70 69 61 20 65 20 63 6f 6c 61 41 63 65 64 |copia e colaAced| 00000010 65 72 20 61 20 74 6f 64 6f 20 6f 20 74 65 78 74 |er a todo o text| 00000020 6f 20 66 61 6c 61 64 6f 20 75 74 69 6c 69 7a 61 |o falado utiliza| 00000030 6e 64 6f 20 61 20 63 6f 6e 76 65 72 73 c3 a3 6f |ndo a convers..o| 00000040 20 64 65 20 74 65 78 74 6f 20 70 61 72 61 20 76 | de texto para v| 00000050 6f 7a 4d 61 6e 69 70 75 6c 61 72 20 61 73 20 64 |ozManipular as d| 00000060 65 66 69 6e 69 c3 a7 c3 b5 65 73 20 71 75 65 20 |efini....es que | 00000070 63 6f 6e 74 72 6f 6c 61 6d 20 6f 20 61 63 65 73 |controlam o aces| 00000080 73 6f 20 64 65 20 57 65 62 73 69 74 65 73 20 61 |so de Websites a| 00000090 20 63 6f 6f 6b 69 65 73 2c 20 4a 61 76 61 53 63 | cookies, JavaSc| 000000a0 72 69 70 74 20 65 20 70 6c 75 67 2d 69 6e 73 4d |ript e plug-insM| 000000b0 61 6e 69 70 75 6c 61 72 20 61 73 20 64 65 66 69 |anipular as defi| 000000c0 6e 69 c3 a7 c3 b5 65 73 20 72 65 6c 61 63 69 6f |ni....es relacio| 000000d0 6e 61 64 61 73 20 63 6f 6d 20 70 72 69 76 61 63 |nadas com privac| 000000e0 69 64 61 64 65 41 63 65 64 65 72 20 61 6f 73 20 |idadeAceder aos | 000000f0 73 65 75 73 20 70 65 72 69 66 c3 a9 72 69 63 6f |seus perif..rico| 00000100 73 20 55 53 42 55 74 69 6c 69 7a 61 72 20 6f 20 |s USBUtilizar o | 00000110 73 65 75 20 6d 69 63 72 6f 66 6f 6e 65 55 74 69 |seu microfoneUti| 00000120 6c 69 7a 61 72 20 61 20 73 75 61 20 63 c3 a2 6d |lizar a sua c..m| 00000130 61 72 61 55 74 69 6c 69 7a 61 72 20 6f 20 73 65 |araUtilizar o se| 00000140 75 20 6d 69 63 72 6f 66 6f 6e 65 20 65 20 61 20 |u microfone e a | 00000150 63 c3 a2 6d 61 72 61 4e c3 a3 6f 20 66 6f 69 20 |c..maraN..o foi | 00000160 70 6f 73 73 c3 ad 76 65 6c 20 65 6e 63 6f 6e 74 |poss..vel encont| 00000170 72 61 72 20 6f 20 63 61 6d 69 6e 68 6f 20 61 62 |rar o caminho ab| 00000180 73 6f 6c 75 74 6f 20 70 61 72 61 20 6f 20 64 69 |soluto para o di| 00000190 72 65 63 74 c3 b3 72 69 6f 20 61 20 65 6d 70 61 |rect..rio a empa| 000001a0 63 6f 74 61 72 2e 4f 20 64 69 72 65 63 74 c3 b3 |cotar.O direct..| 000001b0 72 69 6f 20 64 65 20 65 6e 74 72 61 64 61 00 fe |rio de entrada..| 000001c0 ff ff 83 fe ff ff 02 00 00 00 00 10 7a 04 00 00 |............z...| 000001d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200 =============================== StdErr Messages: =============================== xz: (stdin): Compressed data is corrupt xz: (stdin): Compressed data is corrupt awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in Begging / Appreciation ;) If anything else is required to solve my problem, please ask. My only hopes are that I can solve this, and that doing so won't require re-installation of Grub due to how complicated the procedures are, or that I would be needed to reinstall the OS', as I have done so about six times already since friday due to several other issues I've encountered. Thank you, and good day. System Ubuntu 12.04 64-bit / Windows 7 SP1 64-bit 64GB SSD as boot/OS drive, 1TB HDD as /Home Swap and Steam drive.

    Read the article

  • Ubuntu 14.04 Boot Problem

    - by Sanyam Jain
    I am currently using windows 7 and wanted to try out Linux. I found out that Ubuntu is the most easy to learn Linux OS. So I create a Live USB of Ubuntu 14.04 with the help of the following link: How to make your own "Ubuntu LiveUSB" I created the Live USB successfully, but when I started my PC, i encountered an error message saying : Kernel Panic - not syncing: Attempted to kill init! Along with a lot of commands which I cannot even understand. I would be very grateful if anyone can tell me what is wrong.

    Read the article

  • USB mouse does not work on boot

    - by Uku Loskit
    My problem is pretty much a duplicate of the one described in USB mouse late to load , but the solution there has not worked for me. I'm running the same OS and experiencing the exact same issue. It disappears after 10 seconds or so. Booting with the options specified in the other question did not fix it :/ Thanks in advance. sheepz@sheepz-desktop:~$ dmesg | egrep "hci|usb" [ 0.188000] usbcore: registered new interface driver usbfs [ 0.188000] usbcore: registered new interface driver hub [ 0.188000] usbcore: registered new device driver usb [ 0.358613] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.358627] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.358637] uhci_hcd: USB Universal Host Controller Interface driver [ 0.358683] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.358691] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.358695] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.358726] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 0.358758] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e100 [ 0.358927] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.358932] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.358935] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.358964] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 0.358991] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e200 [ 0.359132] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.359137] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.359139] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.359165] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 0.359193] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e300 [ 0.359327] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 [ 0.359332] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 0.359334] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 0.359360] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 0.359387] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e400 [ 0.731933] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 1.023859] usb 1-2: new full speed USB device using uhci_hcd and address 3 [ 16.136175] usb 1-2: device descriptor read/64, error -110 [ 31.352481] usb 1-2: device descriptor read/64, error -110 [ 31.568485] usb 1-2: new full speed USB device using uhci_hcd and address 4 [ 46.680794] usb 1-2: device descriptor read/64, error -110 [ 61.903555] usb 1-2: device descriptor read/64, error -110 [ 62.119671] usb 1-2: new full speed USB device using uhci_hcd and address 5 [ 72.541078] usb 1-2: device not accepting address 5, error -110 [ 72.653194] usb 1-2: new full speed USB device using uhci_hcd and address 6 [ 83.066637] usb 1-2: device not accepting address 6, error -110 [ 83.178615] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 83.562546] usbcore: registered new interface driver hiddev [ 83.578827] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb3/3-1/3-1:1.0/input/input3 [ 83.579016] generic-usb 0003:046D:C01D.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-1/input0 [ 83.579244] usbcore: registered new interface driver usbhid [ 83.579246] usbhid: USB HID core driver [114025.224407] usb 3-1: USB disconnect, address 2 sheepz@sheepz-desktop:~$ dmesg | egrep "hci|usb" [ 0.188000] usbcore: registered new interface driver usbfs [ 0.188000] usbcore: registered new interface driver hub [ 0.188000] usbcore: registered new device driver usb [ 0.358613] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.358627] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.358637] uhci_hcd: USB Universal Host Controller Interface driver [ 0.358683] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.358691] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.358695] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.358726] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 0.358758] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e100 [ 0.358927] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.358932] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.358935] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.358964] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 0.358991] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e200 [ 0.359132] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.359137] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.359139] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.359165] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 0.359193] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e300 [ 0.359327] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 [ 0.359332] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 0.359334] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 0.359360] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 0.359387] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e400 [ 0.731933] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 1.023859] usb 1-2: new full speed USB device using uhci_hcd and address 3 [ 16.136175] usb 1-2: device descriptor read/64, error -110 [ 31.352481] usb 1-2: device descriptor read/64, error -110 [ 31.568485] usb 1-2: new full speed USB device using uhci_hcd and address 4 [ 46.680794] usb 1-2: device descriptor read/64, error -110 [ 61.903555] usb 1-2: device descriptor read/64, error -110 [ 62.119671] usb 1-2: new full speed USB device using uhci_hcd and address 5 [ 72.541078] usb 1-2: device not accepting address 5, error -110 [ 72.653194] usb 1-2: new full speed USB device using uhci_hcd and address 6 [ 83.066637] usb 1-2: device not accepting address 6, error -110 [ 83.178615] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 83.562546] usbcore: registered new interface driver hiddev [ 83.578827] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb3/3-1/3-1:1.0/input/input3 [ 83.579016] generic-usb 0003:046D:C01D.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.2-1/input0 [ 83.579244] usbcore: registered new interface driver usbhid [ 83.579246] usbhid: USB HID core driver

    Read the article

  • Easy BCD Help: Dual boot Win7 and Ubuntu 11.10 -- "Add new Entry" for Ubuntu

    - by Bradley Peterson
    I first had Ubuntu 11.10 installed on a single partition on my 750GB hard drive. I then partitioned the hard drive to 500GB (for Ubuntu) in ext4 format (what it already was from the clean install of Ubuntu)....and 250GB for Win7 in NFTS format. Then I installed Win7 onto that 250GB partition. Installation went smoothly and I was successfully booted into Win7 and setting everything up. After I was done doing all the stupid updates from Microsof, I thought I was done and I wanted to go back to Ubuntu. This is where the problem starts Of course I reboot and it goes directly to Win7. I research and find that Win7 has overwritten the Ubuntu bootloader, etc etc.. I don't fully understand it. I download EasyBCD 2.1.2 In EasyBCD, I select "Add New Entry" and select "Linux/BSD" and change the type to "GRUB 2" and name it "Ubuntu" Next, I go to "BCD Deployment" and select "Install the Windows Vista/7 bootloader to the MBR" and click "Write MBR" I reboot, select "Ubuntu" and the purple screen comes up, but NOTHING HAPPENS. If I hit Ctrl+Alt+Del, it goes to the Login menu where it acts normal for about 10-15 seconds, then freezes. It does this repeatedly every time. MY QUESTION: What's wrong here? Why can't I load Ubuntu now? Am I going to have to reinstall Ubuntu with Windows, then set up the bootloader with EasyBCD instead of Ubuntu, THEN Win7? Any and all help is appreciated! -Brad

    Read the article

  • Slow boot on Ubuntu 12.04

    - by Hailwood
    My Ubuntu is booting really slow (Windows is booting faster...). I am using Ubuntu a Dell Inspiron 1545 Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, 4GB Ram, 500GB HDD running Ubuntu 12.04 with gnome-shell 3.4.1. After running dmesg the culprit seems to be this section, in particular the last three lines: [26.557659] ADDRCONF(NETDEV_UP): eth0: link is not ready [26.565414] ADDRCONF(NETDEV_UP): eth0: link is not ready [27.355355] Console: switching to colour frame buffer device 170x48 [27.362346] fb0: radeondrmfb frame buffer device [27.362347] drm: registered panic notifier [27.362357] [drm] Initialized radeon 2.12.0 20080528 for 0000:01:00.0 on minor 0 [27.617435] init: udev-fallback-graphics main process (1049) terminated with status 1 [30.064481] init: plymouth-stop pre-start process (1500) terminated with status 1 [51.708241] CE: hpet increased min_delta_ns to 20113 nsec [59.448029] eth2: no IPv6 routers present But I have no idea how to start debugging this. sudo lshw -C video $ sudo lshw -C video *-display description: VGA compatible controller product: RV710 [Mobility Radeon HD 4300 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=fglrx_pci latency=0 resources: irq:48 memory:e0000000-efffffff ioport:de00(size=256) memory:f6df0000-f6dfffff memory:f6d00000-f6d1ffff After loading the propriety driver my new dmesg log is below (starting from the first major time gap): [2.983741] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [25.094327] ADDRCONF(NETDEV_UP): eth0: link is not ready [25.119737] udevd[520]: starting version 175 [25.167086] lp: driver loaded but no devices found [25.215341] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [25.215345] Disabling lock debugging due to kernel taint [25.231924] wmi: Mapper loaded [25.318414] lib80211: common routines for IEEE802.11 drivers [25.318418] lib80211_crypt: registered algorithm 'NULL' [25.331631] [fglrx] Maximum main memory to use for locked dma buffers: 3789 MBytes. [25.332095] [fglrx] vendor: 1002 device: 9552 count: 1 [25.334206] [fglrx] ioport: bar 1, base 0xde00, size: 0x100 [25.334229] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [25.334235] pci 0000:01:00.0: setting latency timer to 64 [25.337109] [fglrx] Kernel PAT support is enabled [25.337140] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [25.342803] Adding 4189180k swap on /dev/sda7. Priority:-1 extents:1 across:4189180k [25.364031] type=1400 audit(1338241723.027:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=606 comm="apparmor_parser" [25.364491] type=1400 audit(1338241723.031:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=606 comm="apparmor_parser" [25.364760] type=1400 audit(1338241723.031:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=606 comm="apparmor_parser" [25.394328] wl 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [25.394343] wl 0000:0c:00.0: setting latency timer to 64 [25.415531] acpi device:36: registered as cooling_device2 [25.416688] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:34/LNXVIDEO:00/input/input6 [25.416795] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) [25.416865] [Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work. [25.425133] lib80211_crypt: registered algorithm 'TKIP' [25.448058] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [25.448321] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [25.448353] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [25.738867] eth1: Broadcom BCM4315 802.11 Hybrid Wireless Controller 5.100.82.38 [25.761213] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [25.761406] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [25.783432] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [25.908318] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro [25.928155] input: Dell WMI hotkeys as /devices/virtual/input/input9 [25.960561] udevd[543]: renamed network interface eth1 to eth2 [26.285688] init: failsafe main process (835) killed by TERM signal [26.396426] input: PS/2 Mouse as /devices/platform/i8042/serio2/input/input10 [26.423108] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio2/input/input11 [26.511297] Bluetooth: Core ver 2.16 [26.511383] NET: Registered protocol family 31 [26.511385] Bluetooth: HCI device and connection manager initialized [26.511388] Bluetooth: HCI socket layer initialized [26.511391] Bluetooth: L2CAP socket layer initialized [26.512079] Bluetooth: SCO socket layer initialized [26.530164] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [26.530168] Bluetooth: BNEP filters: protocol multicast [26.553893] type=1400 audit(1338241724.219:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=928 comm="apparmor_parser" [26.554860] Bluetooth: RFCOMM TTY layer initialized [26.554866] Bluetooth: RFCOMM socket layer initialized [26.554868] Bluetooth: RFCOMM ver 1.11 [26.557910] type=1400 audit(1338241724.223:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=927 comm="apparmor_parser" [26.559166] type=1400 audit(1338241724.223:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=928 comm="apparmor_parser" [26.559574] type=1400 audit(1338241724.223:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=928 comm="apparmor_parser" [26.575519] type=1400 audit(1338241724.239:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=931 comm="apparmor_parser" [26.581100] type=1400 audit(1338241724.247:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=931 comm="apparmor_parser" [26.582794] type=1400 audit(1338241724.247:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=929 comm="apparmor_parser" [26.605672] ppdev: user-space parallel port driver [27.592475] sky2 0000:09:00.0: eth0: enabling interface [27.604329] ADDRCONF(NETDEV_UP): eth0: link is not ready [27.606962] ADDRCONF(NETDEV_UP): eth0: link is not ready [27.852509] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [27.852513] vesafb: scrolling: redraw [27.852515] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [27.852523] mtrr: type mismatch for e0000000,400000 old: write-back new: write-combining [27.852527] mtrr: type mismatch for e0000000,200000 old: write-back new: write-combining [27.852531] mtrr: type mismatch for e0000000,100000 old: write-back new: write-combining [27.852534] mtrr: type mismatch for e0000000,80000 old: write-back new: write-combining [27.852538] mtrr: type mismatch for e0000000,40000 old: write-back new: write-combining [27.852541] mtrr: type mismatch for e0000000,20000 old: write-back new: write-combining [27.852544] mtrr: type mismatch for e0000000,10000 old: write-back new: write-combining [27.852548] mtrr: type mismatch for e0000000,8000 old: write-back new: write-combining [27.852551] mtrr: type mismatch for e0000000,4000 old: write-back new: write-combining [27.852554] mtrr: type mismatch for e0000000,2000 old: write-back new: write-combining [27.852558] mtrr: type mismatch for e0000000,1000 old: write-back new: write-combining [27.853154] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc90005580000, using 3072k, total 3072k [27.853405] Console: switching to colour frame buffer device 128x48 [27.853426] fb0: VESA VGA frame buffer device [28.539800] fglrx_pci 0000:01:00.0: irq 48 for MSI/MSI-X [28.540552] [fglrx] Firegl kernel thread PID: 1168 [28.540679] [fglrx] Firegl kernel thread PID: 1169 [28.540789] [fglrx] Firegl kernel thread PID: 1170 [28.540932] [fglrx] IRQ 48 Enabled [29.845620] [fglrx] Gart USWC size:1236 M. [29.845624] [fglrx] Gart cacheable size:489 M. [29.845629] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [29.845632] [fglrx] Reserved FB block: Unshared offset:fc21000, size:3df000 [29.845635] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [59.700023] eth2: no IPv6 routers present

    Read the article

  • Installing on a mac without a CD burner or USB boot

    - by Rafael
    I am new to Ubuntu, i installed it in an old PC and now it works GREAT!!! My Macbook pro has a glitch and refuses to run Mac OS X, so i installed Windows, and i really want Ubuntu since Windows is not for me. Here's the problem(s) my drive only READS DVDs, if i put a blank in it, it will ignore it and my mac has the updated EFI, so no booting from a USB connected device! I also tried Wubi, but then i cant make it a FULL partition and get rid of windows!!! Thank you!

    Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >