Search Results

Search found 802 results on 33 pages for 'caliburn micro'.

Page 26/33 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

  • Is Windows Server 2008R2 NAP solution for NAC (endpoint security) valuable enough to be worth the hassles?

    - by Warren P
    I'm learning about Windows Server 2008 R2's NAP features. I understand what network access control (NAC) is and what role NAP plays in that, but I would like to know what limitations and problems it has, that people wish they knew before they rolled it out. Secondly, I'd like to know if anyone has had success rolling it out in a mid-size (multi-city corporate network with around 15 servers, 200 desktops) environment with most (99%) Windows XP SP3 and newer Windows clients (Vista, and Win7). Did it work with your anti-virus? (I'm guessing NAP works well with the big name anti-virus products, but we're using Trend micro.). Let's assume that the servers are all Windows Server 2008 R2. Our VPNs are cisco stuff, and have their own NAC features. Has NAP actually benefitted your organization, and was it wise to roll it out, or is it yet another in the long list of things that Windows Server 2008 R2 does, but that if you do move your servers up to it, you're probably not going to want to use. In what particular ways might the built-in NAP solution be the best one, and in what particular ways might no solution at all (the status quo pre-NAP) or a third-party endpoint security or NAC solution be considered a better fit? I found an article where a panel of security experts in 2007 say NAC is maybe "not worth it". Are things better now in 2010 with Win Server 2008 R2?

    Read the article

  • Are HDMI to VGA Adapters Really Device-Specific?

    - by allquixotic
    There are a lot of devices on the market right now (especially mobile devices) with a Micro-HDMI or Mini-HDMI port and no VGA or D-Sub output. Most manufacturers of said devices sell a cable that looks something like this: I have yet to find a cable like this that claims to work on a wide array of devices. In general, these cables claim to work with one specific device only. The way these cables work, I think, is that analog VGA signals are sent from the HDMI port on the device. This should work for devices that have special hardware on the motherboard/GPU capable of driving this. Is it the case that these cables have to be custom designed for each device? Or, is it rather that any device which possesses this special "signaling of analog VGA over the HDMI port" can be made to work with a cable that is physically compatible (i.e. the HDMI end plugs into the device and the VGA end accepts a VGA monitor cable)? Note that I am not looking for a product recommendation, just a conceptual clarification on what exactly these devices are doing. Also, a few remarks: The cables like the one depicted here are not digital to analog converters. I know about these: they are expensive, and they are the ONLY solution if your device only outputs a digital signal and is incapable of driving analog VGA over the HDMI port. The cables like the one depicted here are not straight crossover cables from VGA to HDMI, either. The crossover cables are designed to send a digital HDMI signal over the VGA port's wires; that is, the wire protocol is HDMI (digital) but the physical pinout is the same as VGA, even though nothing analog is happening. Once again, this is not the behavior that, I believe, the devices which I'm talking about in this question are doing. The cabling and devices that this question is about transmit the analog VGA data over the HDMI port (the HDMI port is in the device outputting the data, and the VGA side is the monitor/projector).

    Read the article

  • nginx not serving admin static files?

    - by toto_tico
    First, I want to clarify that this error is just for the admin static files. This means my problem is specific just to the static files that corresponds to the Django admin. The rest of the static files are working perfect. Basically my problem is that for some reason I cannot access those admin static files with the ngix server. It works perfect with the micro server of Django and the collect static is doing its job. This means it is putting the files on the expected place in the static folder. The urls are correct but I cannot even access the admin static files directly, but the others I can. So, for example, I am able to access this url (copying it in the browser): myserver.com:8080/static/css/base/base.css but i am not able to access this other url (copying it in the browser): myserver.com:8080/static/admin/css/admin.css I also tried to copy the admin/ directory structure into other_admin_directory_name/. Then I can access myserver.com:8080/static/other_admin_directory_name/css/admin.css Then, it works. So, I checked permissions and everything is fine. I tried to change ADMIN_MEDIA_PREFIX = '/static/admin/' to ADMIN_MEDIA_PREFIX = '/static/other_admin_directory_name/', it doesn't work. This a mistery in itself that I am exploring but still no luck. Finally, and it seems to be an important clue: I tried to copy the admin/ directory structure into admin_and_then_any_suffix/. Then I cannot access myserver.com:8080/static/admin_and_then_any_suffix//css/admin.css So, if the name of the directory starts with admin (for example administration or admin2) it doesn't work. * added thanks to sarnold observation ** the problem seems to be in the nginx configuration file /etc/nginx/sites-available/mysite location /static/admin { alias /home/vl3/.virtualenvs/vl3/lib/python2.7/site-packages/django/contrib/admin/media/; }

    Read the article

  • Cooling Server Closet - No A/C Is Possible

    - by JamesCo
    We're moving into a new office in an old building in London (that's England :) and are walling off a 2m x 1.3m area where the router & telephone equipment currently terminates to use as a server closet. The closet will contain: 2 24-port switches 1 router 1 VSDL modem 1 Dell desktop 1 4-bay NAS 1 HP micro-server 1 UPS Miscellaneous minor telephony boxes. There is no central A/C in the office and there never will be. We can install ducting to the outside quite easily - it's only a couple of metres to the windows, which face a courtyard. My question is whether installing an extractor fan with ducting to the window should be sufficient for cooling? Would an intake fan and intake duct (from the window, too) be required? We don't want to leave a gap in the closet door as that'll let noise out into the office. If we don't have to put a portable A/C unit into the closet, that'd be perfect. The office has about 12 people; London is temperate, average maximum in August is 31 Celsius, 25 Celsius is more typical. The same equipment runs fine in our current office (same building as new office, also no A/C) but it isn't in an enclosed space. I can see us putting say one Dell 2950 tower server into the closet, but no more than that. So, sustained power consumption in the closet would currently be about 800w (I'm guessing); possibly in the future 2kw. The closet will have a ceiling and no windows and be well-insulated. We don't care if the equipment runs hot, so long as it runs and we don't hear it.

    Read the article

  • Blender refuses to start

    - by Sekhemty
    I'm trying to run Blender under Linux, but I'm unable to do that, whenever I try I get some errors. I'm using Kubuntu 12.04 with KDE 4.11.1. This is my video card: ~$ lspci | grep VGA 01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV610/M74 [Mobility Radeon HD 2400 XT] I used to have installed the fglrx proprietary Catalyst drivers, but lately they gave me some system-wide problems and I had to revert to the open source Mesa drivers (I don't think that these details are important, but just in case, the whole story is here). Whit the fglrx drivers Blender was running fine, but now, whenever I try to start it, I get this error message (some parts are in italian, but I think that they are easily understandable): ~$ blender connect failed: No such file or directory Writing: /tmp/blender.crash.txt Errore di segmentazione (core dump creato) The content of /tmp/blender.crash.txt is as follows: # Blender 2.68 (sub 5), Revision: 60150 # backtrace /usr/lib/blender/blender() [0x877a41f] [0xb7756400] /usr/lib/i386-linux-gnu/libLLVM-3.0.so.1(_ZN4llvm3ARM8SPRClassC1Ev+0x15) [0xa8f4a9d5] /usr/lib/i386-linux-gnu/libLLVM-3.0.so.1(+0x25ca48) [0xa8eefa48] /lib/ld-linux.so.2(+0xeeab) [0xb7765eab] /lib/ld-linux.so.2(+0xef94) [0xb7765f94] /lib/ld-linux.so.2(+0x12fa6) [0xb7769fa6] /lib/ld-linux.so.2(+0xeccf) [0xb7765ccf] /lib/ld-linux.so.2(+0x127f4) [0xb77697f4] /lib/i386-linux-gnu/libdl.so.2(+0xbe9) [0xb4ff9be9] /lib/ld-linux.so.2(+0xeccf) [0xb7765ccf] /lib/i386-linux-gnu/libdl.so.2(+0x133a) [0xb4ffa33a] /lib/i386-linux-gnu/libdl.so.2(dlopen+0x47) [0xb4ff9c97] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(+0x3cbf0) [0xb7717bf0] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(+0x4079d) [0xb771b79d] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(+0x1a3aa) [0xb76f53aa] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(glXQueryVersion+0x2e) [0xb76f0cee] /usr/lib/blender/blender(_ZN15GHOST_WindowX11C1EP15GHOST_SystemX11P9_XDisplayRK10STR_Stringiijj18GHOST_TWindowStatei25GHOST_TDrawingContextTypebbt+0x11c) [0x8f54aec] /usr/lib/blender/blender(_ZN15GHOST_SystemX1112createWindowERK10STR_Stringiijj18GHOST_TWindowState25GHOST_TDrawingContextTypebbti+0xd7) [0x8f4f4a7] /usr/lib/blender/blender(GHOST_CreateWindow+0xb6) [0x8f4cf86] /usr/lib/blender/blender(wm_window_add_ghostwindows+0x205) [0x8799be5] /usr/lib/blender/blender(WM_check+0x50) [0x877b670] /usr/lib/blender/blender(wm_homefile_read+0x111) [0x87859f1] /usr/lib/blender/blender(WM_init+0xd2) [0x8787872] /usr/lib/blender/blender(main+0xe6e) [0x873848e] /lib/i386-linux-gnu/libc.so.6(__libc_start_main+0xf3) [0xb4e694d3] /usr/lib/blender/blender() [0x8778a99] The only thing that I can guess from this report is that the mesa drivers are somewhat involved, as I already suspected, but I don't have a clue on what I need to do to try to solve the issue.

    Read the article

  • Android failure to boot on LG [migrated]

    - by Ukavi
    I need to recover data from my AT&T LG Thrill Android Phone Background: My AT&T LG Thrill phone's battery died a couple of days ago because I forgot to charge it. When I charged the phone and tried to turn it on, it showed the LG logo followed by the dropping balls and the AT&T "Rethink Possible" screen. I then get a mesage that the Application Google Services Framework has crashed and the phone goes into a loop with the dropping balls showing again followed by "Rethink Possible" screen. This sequence repeats itself over and over and the phone does not get out of this loop. I have been able to go into the recovery screen (both Safe Mode and the Android Recovery Service) and have cleared cache, etc. However, I DO NOT want to wipe user data and restore to factory settings as this will wipe all of my data (pictures, application data, etc). Solution Needed: I need a suggestion to a way of accessing my data so that I can back it up onto an SD card/computer. I DO NOT want to root the phone as this may void the warranty. What I'm looking for is a way of perhaps putting the original flash image on the micro SD card and then have the phone read that image. Or some other similar solution that will get the phone out of this loop and allow me to get to the data.

    Read the article

  • Incorrect deployment of WSGI app to AWS using Elastic Beanstalk

    - by Dzmitry Zhaleznichenka
    cross-link to AWS forums I have developed a simple Python web service using WSGI and would like to deploy it to AWS cloud using Elastic Beanstalk. My problem is I cannot make all the options I specify in Elastic Beanstalk configuration to be correctly configured in the cloud. For deployment, I use Elastic Beanstalk CLI utility. I have run eb init command and set up the required parameters. After this, a directory named .elasticbeanstalk was created in my source tree. It has two config files that are used for deployment, namely config and optionsettings. The latter one among the other options contains the WSGI configuration that has to update /etc/httpd/conf.d/wsgi.conf at the instances. After some of my adjustments the file has the following settings: [aws:elasticbeanstalk:application:environment] DJANGO_SETTINGS_MODULE = PARAM1 = PARAM2 = PARAM4 = PARAM3 = PARAM5 = [aws:elasticbeanstalk:container:python] WSGIPath = handler.py NumProcesses = 2 StaticFiles = /static= NumThreads = 10 [aws:elasticbeanstalk:container:python:staticfiles] /static = static/ [aws:elasticbeanstalk:hostmanager] LogPublicationControl = false [aws:autoscaling:launchconfiguration] InstanceType = t1.micro EC2KeyName = zmicier-aws [aws:elasticbeanstalk:application] Application Healthcheck URL = [aws:autoscaling:asg] MaxSize = 10 MinSize = 1 Custom Availability Zones = [aws:elasticbeanstalk:monitoring] Automatically Terminate Unhealthy Instances = true [aws:elasticbeanstalk:sns:topics] Notification Endpoint = Notification Protocol = email It turns out that not all of these options are considered when I start the environment or update it. Thus, when I update NumThreads or NumProcesses, the respective parameters get changed in wsgi.conf as expected. But whatever I write to the WSGIPath and StaticFiles parameters, I'm not able to automatically change the respective values of wsgi.conf, they remain Alias /static /opt/python/current/app/ WSGIScriptAlias / /opt/python/current/app/application.py which drives me nuts. Moreover, when I deploy my application using git aws.push and having the following contents of .ebextensions/python.config file, neither of options I specify in it affects the deployment. option_settings: - namespace: aws:elasticbeanstalk:container:python option_name: WSGIPath value: mysite/wsgi.py - namespace: aws:elasticbeanstalk:container:python option_name: NumProcesses value: 5 - namespace: aws:elasticbeanstalk:container:python option_name: NumThreads value: 25 - namespace: aws:elasticbeanstalk:container:python:staticfiles option_name: /static/ value: app/static/ I wonder what I should do to force AWS use all the parameters I specify in the configuration, namely the WSGI Path and path to my static data.

    Read the article

  • How do I make ESXi 5.0 to shutdown virtual machines when the physical power button is pushed?

    - by Pawel Sawicki
    I have a home NAS/DLNA server built out of an HP Micro Server with the HP branded VMware ESXi 5.0.0 build-623860 (free license) installed. Being a home media center I'd like it to be "manageable" by all my household members. This requires that it needs to be powered on an off (including all the VMs inside) by anybody with the physical access to the server by simply pressing the power button on the chassis. The "startup" part is easy to obtain - all I had to do was to configure the startup/shutdown policy: Once the server powers up, all VMs start as well and that's exactly what I need. Well.. it did work up until 5.0.0U1, but that's a different story: http://blogs.vmware.com/vsphere/2012/03/free-esxi-hypervisor-auto-start-breaks-with-50-update-1.html Unfortunately, pressing the power button doesn't gracefully shutdown the guest machines - they are terminated instead. If I run the "shut down" command from the vSphere Client interface guests are powered off. I'd like to get the same end result when the physical power button is switched. I've poked around a bit on the ESXi server. There's a "/sbin/shutdown.sh" script that seemed to do exactly what I need... but after trying it does exactly what the power off button. The "/etc/inittab" contains an entry for the "shutdown" level but I suppose it's not hooked to the power button. I can't find any acpi related configuration, neither do I know what exactly is executed when the power button is pressed. Does anybody have a clue how can I make the VMs shutdown automatically when the physical power switch is pressed to turn of the computer?

    Read the article

  • Slow boot for OS and external devices

    - by Derek Van Cuyk
    I have been having this problem intermittently but as of yesterday, it has become more consistent. It originally started when I rebooted my PC at home and the OS (Windows 8) sat in a loop appearing to do nothing while loading. I figured since this was a new installation, that something may have just become corrupted and I decided to reinstall. So I tried to boot off of the thumb drive which had the installation iso and encountered pretty much the same issue. Same with the DVD drive. So, I rebooted once again and left it to load the entire night just to see if it ever would and sure enough this morning, Windows had finally loaded. Authentication had the same roblem albeit not quite as long (took about 5 minutes to authenticate). However, once I was in, everything appeared to be working fine and as quick as normal with the exception of when I tried to scan the C drive for any errors, which ran unbearably slow (45 minutes and before I left for work and was not finished scanning a 64GB SSD drive). I mention that I have had this issue but never when loading the OS. Before it occurred when trying to install windows 7 from a different DVD drive than the one I have now. It took me about 3 hours to do it since I had to wait sometimes 30+ min for each step to finish processing. Does anyone have an idea as to what can cause this? I am assuming it is the motherboard since it is responsible for communication with all the devices I'm having issues with but I cannot find anyone else who has had a problem like this and don't want to drop more money on a MB if it isn't the problem. Hardware: Motherboard: Asus M4A78T-E Socket AM3/ AMD 790GX/ Hybrid CrossFireX Hard Drive: Kingston SSDNow V+180 64GB Micro SATA II 3GB/S 1.8 Inch Solid State Drive SVP180S2/64G Optical Drive: Samsung Blu-Ray Combo Internal 12XReadable and DVD-Writable Drive with Lightscribe SH-B123L/BSBP Thanks, Derek

    Read the article

  • No audio in my ubuntu system

    - by hap497
    Hi, I am running ubuntu 9.10. But there is no sound in my environment. When I go to System-Preference, there is no 'sound' entry there. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: I82801AAICH [Intel 82801AA-ICH], device 0: Intel ICH [Intel 82801AA-ICH] Subdevices: 1/1 Subdevice #0: subdevice #0 $ lsmod Module Size Used by usb_storage 52576 3 binfmt_misc 8356 1 vboxvfs 34620 0 vboxvideo 1884 1 drm 159584 2 vboxvideo agpgart 34988 1 drm snd_intel8x0 30168 2 snd_ac97_codec 101216 1 snd_intel8x0 ac97_bus 1532 1 snd_ac97_codec snd_pcm_oss 37920 0 snd_mixer_oss 16028 1 snd_pcm_oss snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_seq_dummy 2656 0 snd_seq_oss 28576 0 iptable_filter 3100 0 snd_seq_midi 6432 0 ip_tables 11692 1 iptable_filter x_tables 16544 1 ip_tables snd_rawmidi 22208 1 snd_seq_midi snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi ppdev 6688 0 snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event snd_timer 22276 2 snd_pcm,snd_seq snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq psmouse 56500 0 serio_raw 5280 0 snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_ oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_ti mer,snd_seq_device i2c_piix4 9932 0 parport_pc 31940 0 soundcore 7264 1 snd snd_page_alloc 9156 2 snd_intel8x0,snd_pcm vboxguest 143836 7 vboxvfs lp 8964 0 parport 35340 3 ppdev,parport_pc,lp pcnet32 32644 0 mii 5212 1 pcnet32 floppy 54916 0 ~:987:2$ lspci 00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02) 00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] 00:01.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter 00:03.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 40) 00:04.0 System peripheral: InnoTek Systemberatung GmbH VirtualBox Guest Service 00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (rev 01) 00:06.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB 00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 0 00:0b.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller ~:988:3$

    Read the article

  • PC can't detect second RAM installed

    - by kulwinder
    I have PC with 512 MB RAM installed (motherboard manufacture MICRO STAR, chipset P4M800), pc was running very slow so I decided to upgrade the ram. I installed CPU-Z and check the ram installed on the machine, also had a look at the stick installed. 512 MB PC 3200 400 MHz DDR but my mother supports 200 MHz and it was working ok. So I bought 2GB which I checked on manual that it support upto 2 GB Ram. So I installed 2GB PC 3200 400 MHz same as the old one, I plugged in both eventhough motherboard only support upto 2 GB but system spec only shows 512 (deducts 64 MB shared vga memory) I checked on CPU-Z, it detects both, slot 1 512 MB, slot 2 2048 MB, comparing screen for both slots, both the same, volt 2.5, frequency 166 MHz and 200MHz, only difference on those is 2gb ram shows under timings table 133MHz 166 MHz and 200MHz but 512 MB shows only 166MHz and 200MHz. I checked on Google and can't seems to figure out whats wrong with it. If I only plug in 2GB. Pc doesn't boot up like ram not working.With only 512 MB plugged in seems ok. Please help.

    Read the article

  • bootmgr image is corrupt

    - by bacord
    I just replaced my HD with a SSD. I did a brand new install on the SSD and I received the following error after booting BOOTMGR image is corrupt. The system cannot boot. A little configuration for your knowledge. The system used to be a dual boot with XP & windows 7. After replacing the original startup HD with my SSD I changed a setting in the bios to AHCI (I have tested changing it back but this did not help). When I look at the stats on the drive in the bios, it claims that the SSD is in a raid configuration despite the settings not being configured that way. Related System Information: Intel 320 Series 80 GB Sata II SSD JetWay JPA78VM3-H-LF AM2+/AM2 AMD 780V HDMI Micro ATX AMD Motherboard AMD Athlon 64 X2 7 GB ram I have performed 2 fresh installs to no avail. Also, followed this guide and performed option 1 and 2. I have done bootsec/fixmbr and /fixboot. So.. any suggestions?

    Read the article

  • New build won't boot: some fans turning, no beep or video

    - by Dave
    When my new system is powered up, the case fan and power supply fans turn fine. The CPU fan twitches, but never gets going. Although I've heard that with AMDs and Gigabyte motherboards that is not necessary a problem. Hard drive is spinning. However, there is absolutely no indication that anything else is happening. The motherboard, as far as I can tell, does not have an internal speaker, but I harvested one from another machine and plugged it in and still no beeps at all. The monitor screen stays black, on both the integrated VGA and DVI. This is a brand new build, and has never successfully booted. My parts are: AMD Athlon II X2 245 Regor 2.9GHz Socket AM3 65W Dual-Core Processor Model ADX245OCGQBOX - includes CPU cooler) GIGABYTE GA-MA785GPMT-UD2H AM3 AMD 785G HDMI Micro ATX AMD Motherboard - Retail G.SKILL Ripjaws Series 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) Desktop Memory Model F3-10666CL8D-4GBRM - Retail CORSAIR CMPSU-400CX 400W ATX12V V2.2 80 PLUS Certified Compatible with Core i7 Power Supply - Retail SAMSUNG Spinpoint F3 HD502HJ 500GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive COOLER MASTER Elite 341 RC-341C-KKN1-GP Black Steel MicroATX Mid Tower Computer Case - Retail I also have a DVD burner, but it acts the same whether that is plugged in or not. I'm using the on board video. What I've tried so far: I've switched power supplies, with no difference. I've tried different monitors (of which all are working on other machines) with no difference. I have tried putting it one memory module at a time, with no difference. I have tried the absolute minimum I can think of (power supply into motherboard, power button ONLY plugged into front panel, CPU fan plugged in), with no difference. I appreciate any ideas anyone might have. Do I need to RMA the motherboard? This is my first build, so there might be something obvious. I was very careful in assembly with static; I'm confident nothing was zapped during assembly.

    Read the article

  • Debugging Windows PC freeze

    - by Violet Giraffe
    I have a problem with my computer, would appreciate any hints/ideas. It usually begins not immediately after booting Windows, but at some unpredictable point in time, which doesn't seem to correlate with any specific actions of mine. First sign of a problem is process System starting to consume 25% CPU time steadily. I have a quad-core CPU, so it might be one thread working non-stop. At this point micro-freezes start to occur - screen stops refreshing, but if I have, say, music player running - it continues playing. If I try to do something between the freezes, like open Start menu, it will freeze completely and forever. If I press reset button the PC will shut down and then start cold, as opposed to usual reset behavior (which doesn't include PC shutting down). I have noticed that full restart upon reset is usual for hardware problems, but I think this problem isn't related to at least motherboard-CPU-RAM-videoadapter. It certainly isn't caused by overheating. One very important not is that it seems to be related to Windows hosted WLAN network: I have USB Wi-Fi dongle and have configured a hosted network to share cable Internet connection with Wi-Fi devices. I am not 100% certain there's a strong connection, but in 9 or 10 cases when I enabled the network (by executing netsh wlan start hostednetwork), it did freeze eventually (sometimes within minutes of starting the network, sometimes within hours), and on at least 10 days when I didn't start the network it never froze, no matter how I used the computer). There are no critical/error entries in the events log that I can suspect as being related, only regular stuff like "driver not loaded". I have found no critical/error events that are being logged around the time of freeze occurring and are not logged during normal boot without starting the WLAN.

    Read the article

  • Dell Driver Support for Latitude E6320 Windows 7 Enterprise

    - by IamPolaris
    I recently did a reinstall of Windows 7 Enterprise on a Dell Latitude E6320, which is a 64 bit system. After the install process, and doing typical Windows Update stuff, I looked at my Device Manager and found that I had devices which were missing drivers. My missing drivers: After going to the Dell Support site and looking at the files, and doing some sleuthing I found the following support document: http://downloads.dell.com/utility/Latitude%20E-Family%20%20Mobile%20Precision%20Re-Image%20How-To%20Guide%20-%20A03%20Rev%203%200.pdf This document hints in appendix C that the Broadcom USH is the Control Point Security and the Unknown device is Micro freefall sensor. The network controller is my wireless, as I cannot connect wirelessly, and the final missing driver I am not sure. Attempting to install the control point security exe on the support page will not work. After downloading, I am given the message that I am attempting to install a 32 bit driver on a 64 bit machine EVEN THOUGH I selected the win7 64 bit option from the support page. Beyond that, some of the drivers (Which are confusing to read and hard to understand what they do) and the system utilities which are supposedly supposed to make this process simpler will either a) not run because they are 32 bit exe's or b) the support page cannot find the file attempted to download. Is there anything I can do to get (at the very least) my wireless running, but idealistically all of my drivers. A solution which assumes Dell is completely incompetent would be ideal. :P Some forums have said that I should download the chipset driver, others say to get the system utility file (DSS_UTIL_WIN_R282536.EXE). I have had no luck as of yet...

    Read the article

  • Server freezes while installing Redhat Enterprise Linux Server 6

    - by eisaacson
    We've tried both the first options Install or upgrade an existing system Install system with basic video driver When trying option #1, it gets to a screen that has a solid cursor about halfway down, then freezes. When trying option #2, it freezes at the point where it says: Waiting for hardware to initialize... Of course, we bought the unsupported version and haven't found anything to help us so far. Here are the specs to the server in the original post: ASUS P8Z68-M Pro LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard with UEFI BIOS RAIDMAX Reiter ATX-305WBP Black Steel / Plastic ATX Mid Tower Computer Case 450W Power Supply Intel Core i7-2600 Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 2000 BX80623I72600 16GB Ram OCZ Agility 3 SSD 120GB From some of the posts out there could the UEFI Bios or the Sandy Bridge processor be a culprit here? We just tried the DVD on a different computer and it got past that point with ease. It's a standard Dell build compared to our custom machine. Could it be having difficulty recognizing drivers? How do we get past that?

    Read the article

  • Setup a Reverse Proxy with Nginx and Apache on EC2

    - by heavymark
    Good Day, I am currently using the free Amazon EC2 micro instance to learn Linux and server setup. I wish to setup Nginx as a reverse web proxy. I found a great article on mediatemple on how to do it: http://wiki.mediatemple.net/w/Using_Nginx_as_a_Reverse_Web_Proxy The directions work for most any server except for EC2.One difference between EC2 and MediaTemple is how IPs work. Overall EC2 instances do not know their elastic IP. So when following the wiki directions in the virtual hosts for instance instead of myip:80 for instance I put *:80. When just using Apache this works perfectly. In the apache virtual hosts I did "127.0.0.1:80" and in the Nginx I put *:80. Apache restarts, by Nginx provides an error that it cannot bind because the ip is already in use. If I could add an actual IP in the Nginx file it would work but since EC2 requires me to put in the asterisk it ends up conflicting with the apache virtual hosts entry. Anyone know a simple way around this (other than not using EC2) ;-) Thank you! Cheers, Christopher

    Read the article

  • Failure to connect to admin share pops up dialog

    - by Jan
    I'm having an issue with a curious error message when accessing the administrative share on a remote machine. Specifically, the client is logged in as the domain administrator on the machine A, and runs some code that tries to access the admin share on B (a domain member). The access is done in .NET, along these lines (though I am not sure if the method of access makes a difference): string path = @"\\B\admin$"; if (Directory.Exists(path)) { try { path += @"\temp\"; if (!Directory.Exists(path)) { Directory.CreateDirectory(path); } path += "myfile_remote"; File.Copy("myfile", path); Now, on some machines this fails. That is not a big problem as we have a fallback. I'd like to know why but it is not the real issue. The problem is that running this piece of code causes a dialog box to pop up for the logged-in user on B, saying "network error trying to access \\B\admin$\temp\myfile_remote. Contact the network administrator and ask for the correct permissions". Unfortunately, it is a foreign language Windows so I'll spare you all posting a screenshot. It is skinned like a standard Windows dialog box. Why exactly is that dialog box popping up for the user and is there anything I can do about it? Edit to add: B is a Windows 7 Enterprise installation. The client is not aware of any GPO policies being installed. There is AV from Trend Micro installed.

    Read the article

  • MySQL Not Turning On

    - by Shalin Shah
    I have an amazon ec2 instance running on the Amazon Linux AMI and its a micro instance. I wanted to install Django onto my server so I entered these commands wget http://www.mlsite.net/blog/wp-content/uploads/2008/11/go wget http://www.mlsite.net/blog/wp-content/uploads/2008/11/django.conf chmod 744 go ./go So after I was done, I ran sudo service httpd restart and sudo service mysqld restart and This is what came up for mysqld: Stopping mysqld: [ OK ] MySQL Daemon failed to start. Starting mysqld: [FAILED] So I deleted the django files /usr/local/python2.6.8/site-packages/django_registration.egg and I tried finding the error and I found out that in my /etc/my.cnf for the socket, it said socket=/var/lock/subsys/mysql.sock so I went to /var/lock/subsys/ and there was no mysql.sock. I tried creating one using vim but it still didn't work. Then I checked the error log and it said Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) So I am pretty much lost right now. I know it has something to do with mysql.sock If you might know a reason why this was caused could you please let me know? I have a wordpress site on my server, so i kind of need MySQL to work. Thanks!

    Read the article

  • Amazon EC2: Instances, IPs and a wordpress blog (LAMP)

    - by JustinXXVII
    I had a link to my blog posted on Reddit yesterday and MySQL crashed on my EC2 Micro instance. I know I didn't have that many visitors because I used a marketing link that tracks hits. The link got 167 hits over the course of the last 18 hours, and MySQL crashed twice. So anyway, 167 visits is not a lot, so I've done some short term optimizations like restricting the number of Apache threads to limit the MySQL calls. I also set up WP Super Cache to serve static content. Soon I'm going to offload all of my images to S3 or CloudFront. So this leads me to my question. If this doesn't seem to help, and if i have another traffic "spike", how do AMIs work when you have a MySQL database? I think I understand that if you have more than one instance and assign the same Elastic IP to both of them, the incoming traffic gets distributed among both. But what happens when the MySQL database gets updated on one of the instances? I just need to wrap my mind around what happens when I create an AMI and then launch a new instance to help with traffic. Thanks for your suggestions.

    Read the article

  • ddwrt client brigde acces point lost

    - by llazzaro
    Ok I have an AP with ddwrt firm (i know its not the best, but continue reading!) AP is configured to work like a wifi "transparent" brigde, also it had a virtual wifi network card to expand radius of wifi signal in that same AP. The brigde is working, computers behind AP gets ips from main routers which shares internet....BUT! I cant access webgui of the bridge AP... Main problem : AP is lost, but its working as brigde. I cant find it in the network (it didnt have any ip!) so I cant change any configuration... First solution : Reset AP, but it cannot be done. Reset button dont works due to a bug in ddwrt micro firm that mi linksys WAP54g had installed (I really hate this firmware I like more openwrt that my main router has) Second Solution : arp -a from main router , from computers behind AP...It dont appears in the list. Any more ideas, the router at some level must be there, the brigde is working. I know its possible that the AP is with an ip like 192.168.100.2 , my subnect actually is 172.16.X.X. :) thanks!

    Read the article

  • processes slow after some time of actively running

    - by Yervand Aghababyan
    i have several cron jobs running on an ubuntu machine. each one does some pretty heavy load stuff. The cron jobs are parsing files and the bigger the file the longer it takes them to parse it. The strange thing is that if i make the files too big ( like 30mb) the script kind of hangs. It starts processing them really enthusiastically but after some time (something like 5-10 minutes) the cpu usage of the process drops a lot and it gets into some "zombie" state. If prior to this the process in htop was using 70-80% of the CPU then after this drop occurs it slows down to something like 5-10%. the load average drops down as well. The status of the processes sometimes changes to D in htop, which AFAIR stands for zombie. Today i noticed the same behavior of processes of mysql when executing heavy queries (a query took something like 4 hours to execute). the cron jobs are mostly php and during their processing most of the CPU eats the php process and not mysql. so i think the issue is not with a specific language/program but with the way the processes are "managed". The only other place i've seen similar behavior was on my Amazon EC2 micro instance when after some aggressive use of CPU the CPU quota was taking effect and everything was slowing down dramatically. This is a dedicated machine running ubuntu. what may be the cause?

    Read the article

  • computer freezes but music continues

    - by Danny
    Recently I have had a problem where my computer will freeze completely but if I happen to be streaming Pandora in a tab that will continue playing. If I wait about 2-5 minutes it will eventually come back and start working normally. I also noticed that during the period that it is unresponsive that the HDD activity light stays lit the whole time, not flashing. I've ran memtest86+ and a diagnostic from Western Digital for my HDD model and none of them reported any errors. The specs for my computer are 1 x ASRock H55M/USB3 R2.0 LGA 1156 Intel H55 HDMI USB 3.0 Micro ATX Intel Motherboard 1 x CORSAIR Enthusiast Series CMPSU-550VX 550W ATX12V V2.2 SLI Ready CrossFire Ready 80 PLUS Certified Active PFC Compatible with Core i7 Power Supply 1 x Intel Core i3-540 Clarkdale 3.06GHz LGA 1156 73W Dual-Core Desktop Processor Intel HD Graphics BX80616I3540 1 x G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ 1 x ASUS PCE-N13 PCI Express 150/300Mbps Transfer/Receive Rate Wireless Adapter 1 x EVGA 01G-P3-1556-KR GeForce GTX 550 Ti (Fermi) FPB 1GB 192-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI Support Video Card I can't imagine what would be causing these problems.

    Read the article

  • Does anyone know where I could find a 2 input USB voltage meter?

    - by John O
    What we really need is a tiny UPS, of sorts. We'll be hooking up a solar cell and a battery to a single board computer. Currently, that SBC is a custom Pic32 device, and it does it's own UPS and voltage monitoring duties. I've been tasked with trying to replicate all of its features with off the shelf products... and for the most part I've succeeded. But I don't currently have any way to switch between two sources of juice, or monitor when they're getting low. These guys have something: http://www.mini-box.com/picoUPS-100-12V-DC-micro-UPS-system-battery-backup-system I really like it, the price is well within the budget. We might even work it in though it does 12V and I'll probably be using 5V... there are enough engineers on hand to figure out something. But I'd still have no idea what the voltage was for the PV or battery. I was hoping that there was some simple little USB multimeter thing that I could use to monitor this with, but I can't seem to come up with anything. I've found all sorts of cool hardware, but nothing that will help us. Does anyone know of anything?

    Read the article

  • Unusual HEAD requests to nonsense URLs from Chrome

    - by JeremyDWill
    I have noticed unusual traffic coming from my workstation the last couple of days. I am seeing HEAD requests sent to random character URLs, usually three or four within a second, and they appear to be coming from my Chrome browser. The requests repeat only three or four times a day, but I have not identified a particular pattern. The URL characters are different for each request. Here is an example of the request as recorded by Fiddler 2: HEAD http://xqwvykjfei/ HTTP/1.1 Host: xqwvykjfei Proxy-Connection: keep-alive Content-Length: 0 User-Agent: Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US) AppleWebKit/534.13 (KHTML, like Gecko) Chrome/9.0.597.98 Safari/534.13 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-US,en;q=0.8 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 The response to this request is as follows: HTTP/1.1 502 Fiddler - DNS Lookup Failed Content-Type: text/html Connection: close Timestamp: 08:15:45.283 Fiddler: DNS Lookup for xqwvykjfei failed. No such host is known I have been unable to find any information through Google searches related to this issue. I do not remember seeing this kind of traffic before late last week, but it may be that I just missed it before. The one modification I made to my system last week that was unusual was adding the Delicious add-in/extension to both IE and Chrome. I have since removed both of these, but am still seeing the traffic. I have run virus scan (Trend Micro) and HiJackThis looking for malicious code, but I have not found any. I would appreciate any help tracking down the source of the requests, so I can determine if they are benign, or indicative of a bigger problem. Thanks.

    Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >