Search Results

Search found 2344 results on 94 pages for 'ethernet'.

Page 26/94 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to get it to work?

  - by zewone

  I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686  Any help much appreciated... Thanks, Philippe 31-10-2012 ... I have some more updates. When I do the following command it does see my Wifi router... So even if it is still disabled... the card seems to work and see the router (ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E") See below: sudo iwlist wlan1 scanning wlan1 Scan completed : Cell 01 - Address: 00:19:70:8F:B0:EA Channel:10 Frequency:2.457 GHz (Channel 10) Quality=51/70 Signal level=-59 dBm Encryption key:on ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000025dbf2188 Extra: Last beacon: 108ms ago IE: Unknown: 002035373931424332362D434539432D313144312D393742462D3030303046383145 IE: Unknown: 010882848B960C121824 IE: Unknown: 03010A IE: Unknown: 0706424520010D14 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101030003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000

  Read the article

• FreeBSD 8.0 - Macbook: Trying to Connect to Wireless

  - by Koroviev

  What Happened A few days ago I installed FreeBSD 8from USB to my Macbook (Core Duo, 13"). The first thing I wanted to do was get my GUI back. I'm new to FreeBSD and it's my first time off of mac or windows, so I had some learning to do. I tried to a make clean install of xorg with ports but it returned many "No address record" errors. I realised I hadn't configured network settings and then the fun started. I ran ifconfig and it found 5 devices: msk0, ath0, fwe0, fwip0, lo0. * ath0 was identified as media: IEEE 802.11 Wireless Ethernet autoselect so it was clear which one I needed. From what I gathered, there are 3 files and two processes involved here: /boot/loader.conf /etc/wpa_supplicant.conf /etc/rc.conf /etc/rc.d/netif wpa_supplicant (which is a part of the former too) I'm certain it's a big simplification, so correct me if I'm wrong here. What I Tried I configured /boot/loader.conf with the few basic settings, and I'm most sure that this file is okay. The other 2 were more puzzling. I tried to make a network package in wpa_supplicant.conf. I found the ssid of the router, but the security wasn't so easy. The routers configuration on security is set to "Auto", with no explanation given. Other options are there, but Auto is selected. Another laptop uses WEP to connect (it's Vista, so I don't know how to get any more info than that), but I never configured it to do it. There's a string labled "wireless key" on the bottom of the router which I entered to set it up a new machine on the network (Windows and Macs, so it was simplified). I never had to choose a security type and only learned about them by installing FreeBSD. So perhaps WEP is what "Auto" means, but I can't find any other evidence. wpa_supplicant.conf seemed to never be correctly configured. I always got errors related to it and WPA_supplicant doesn't work. It gave me "Can't disable/enable WPA in the driver" errors and more once when I enabled -d -d. This was when I was trying some suspect configurations in rc.conf though. Usually it does nothing except hijack the shell and print "CTRL-SCAN-EVENT-RESULT" every 10 seconds. I learned how to clone the ath0 device to a wlandev interface (wlan0). ath0 is associated to it and their connection seems to go smoothly. But the wlan0's connection to the network is the problem. I couldn't create this with rc.conf, I do something wrong and get ifconfig: create: bad value errors whenever it's parsed. I did it via the shell instead. What Now? I scanned with wlan0 today: ifconfig wlan0 list scan It shows my router, even my neighbour's router. It was a relief to finally get some feedback. So wlan0 is UP and detects the router, but it is always status: no carrier. It can't associate with it and I can't figure out why. Running /etc/rc.d/netif start returns almost the same result as ifconfig would. It shows lo0 and wlan0, and sometimes ath0. I still not sure what lo0 is doing. So; how do I associate with it? We can assume it's WEP security based on how the other laptop is setup. I'll give every relevant output here. After boot, with a blank rc.conf this is what ifconfig returns: msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> ether 00:17:f2:29:89:3b media: Ethernet autoselect ath0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 2290 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:17:f2:60:ad:7e ch 1 dma -1 fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 lladdr 0.17.f2.ff.fe.60.ad.7e.a.2.ff.fe.0.0.0.0 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 I run: ifconfig wlan0 create wlandev ath0 It returns: wlan0: bpf attached wlan0: bpf attached wlan0: Ethernet address: xx:xx:xx:xx:xx:xx Ifconfig now returns: msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> ether 00:17:f2:29:89:3b media: Ethernet autoselect ath0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 2290 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:17:f2:60:ad:7e ch 1 dma -1 fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 lladdr 0.17.f2.ff.fe.60.ad.7e.a.2.ff.fe.0.0.0.0 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 wlan0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier ssid "" channel 1 (2412 Mhz 11b) regdomain 106 indoor ecm authmode OPEN privacy OFF txpower 20 bmiss 7 scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi 7 roam:rate 1 wme burst bintval 0 I run: ifconfig wlan0 up ifconfig wlan0 scan It finds my router and displays its details. I can feed it my routers details now, using: ifconfig wlan0 key value key value ... They show up in wlan0 when I run ifconfig, but it still doesn't associate. What details should I feed it, what exactly is needed? What, if anything, should I have in /etc/wpa_supplicant.conf (and if that psk is needed, is it most likely the string I mentioned above)? If I define the ssid in wpa_supplicant.conf, should I still feed it to wlan0? What process should I then use to associate it? 5 .How should I add these things to rc.conf so it will automatically do this at boot? A huge thank you in advance for any help you can give, I've spent hours crawling about the shell and I've learned quite a bit from it (I finally got the hang of vi too, from all that editing). But the sooner this is fixed, the better. *P.S. I was, and still am, wondering where the extra three devices come from (the wireless and wired were all I expected to find). lo0 is up at each boot and /etc/rc.d/netif, I have no idea what it is and can't find it in dmesg. Resources: /etc/loader.conf: Code: if_ath_load="YES" wlan_wep_load="YES" wlan_ccmp_load="YES" wlan_tkip_load="YES" /etc/wpa_supplicant.conf (I emptied it of everything unnecessary, because I was just causing errors) network={ ssid="BTVOYAGER2110-1C" } /etc/rc.conf has no network settings, I commented them out because of errors. There was my attempt to clone ath0 and feed it info, but I did if via the shell instead. I've included the output of dmesg as an attachment, in case it's useful. I'd include the boot text (which appears before login) but I don't know how to catch it into a text file. If it's needed and somebody tells me how, I will (actually, even if it's not needed, how can I view it to read?).

  Read the article

• How to use CLEAR USB internet connection in Ubuntu (host) and WindowsXP (guest) using VirtualBox

  - by bithacker

  I'm trying to use CLEAR Motorola WiMax USB in Ubuntu as there is no support for linux as yet. I've installed windowsxp as guest in ubuntu and the version I'm using is 3.2.2. USB is connecting fine in WindowsXP but I can't use internet in Ubuntu. Can you please tell me how to do it. Here is the configuration that could help you guys. Thanks in advance. I'm using Two Network Adapters. Network Adapter 1: PCnet-FAST III (NAT) Adapter 2: PCnet-FAST III (Host-only adapter, 'vboxnet0') ipconfig [on Guest windowsXP] Windows IP Configuration Ethernet adapter Local Area Connection: PCnet-FAST III (NAT) Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.0.2.15 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.0.2.2 Ethernet adapter Local Area Connection 3: PCnet-FAST III (Host-only adapter, 'vboxnet0') Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.56.101 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : CLEAR Motorola USB IP Address. . . . . . . . . . . . : 10.168.242.33 Subnet Mask . . . . . . . . . . . : 255.255.192.0 Default Gateway . . . . . . . . . : 10.168.192.2 IFCONFIG [on Host Ubuntu] (Ethernet) eth0 Link encap:Ethernet HWaddr 00:14:22:b9:9d:76 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 (Wireless) Link encap:Ethernet HWaddr 00:13:ce:f0:9b:0d inet6 addr: fe80::213:ceff:fef0:9b0d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:84 (84.0 B) Interrupt:17 Base address:0xe000 Memory:dfcff000-dfcfffff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2292 errors:0 dropped:0 overruns:0 frame:0 TX packets:2292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:171952 (171.9 KB) TX bytes:171952 (171.9 KB) vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:192.168.56.1 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::800:27ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:137 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:21174 (21.1 KB)

  Read the article

• Network traffic is not being forwarded from a VM to the network using a bridged interface with Xen + libvirt

  - by foob

  I'm having trouble getting network access from a VM that I'm running using Xen and libvirt. I've been trying different things and reading similar posts online for a couple of days but I'm really stuck at this point. If anybody could offer some insight it would be much appreciated. I have a VM that I'm running on a host with a bridge set up as br0 and an interface eth0 on a 192.168.60.0/24 subnet. The networking portion of the libvirt configuration xml is: <interface type='bridge'> <mac address='ff:a0:d1:e5:07:de'/> <source bridge='br0'/> <script path='/etc/xen/scripts/vif-bridge'/> <model type='virtio' /> </interface> When I start the VM a vif6.0 interface is created on the host and the ifconfig output is: br0 Link encap:Ethernet HWaddr 00:A0:D1:C3:07:DE inet addr:192.168.60.33 Bcast:192.168.60.255 Mask:255.255.255.0 inet6 addr: fe80::2a0:d1ff:fee5:7de/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13 errors:0 dropped:0 overruns:0 frame:0 TX packets:40 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3570 (3.4 KiB) TX bytes:3508 (3.4 KiB) eth0 Link encap:Ethernet HWaddr 00:A0:D1:C3:07:DE inet6 addr: fe80::2a0:d1ff:fee5:7de/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:492 (492.0 b) Interrupt:19 Memory:fe8f0000-fe900000 vif6.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:6660 (6.5 KiB) TX bytes:468 (468.0 b) virbr0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) The 'brctl show' output seems to show the bridge being configured correctly: br0 8000.00a0d1e507de no eth0 vif6.0 The ifcfg-eth0 contents in the VM are: DEVICE=eth0 BOOTPROTO=static HWADDR=FF:A0:D1:E5:07:DE IPADDR=192.168.60.133 NETMASK=255.255.255.0 ONBOOT=yes and the output of ifconfig in the VM look like what I would expect: eth0 Link encap:Ethernet HWaddr FF:A0:D1:E5:07:DE inet addr:192.168.60.133 Bcast:192.168.60.255 Mask:255.255.255.0 inet6 addr: fe80::fda0:d1ff:fee5:7de/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:468 (468.0 b) TX bytes:7780 (7.5 KiB) but when I try to ssh or ping another computer I get 'no route to host.' Using tcpdump on the host system I tried to see if I could narrow down where the problem is: # tcpdump -vv -i vif6.0 tcpdump: WARNING: vif6.0: no IPv4 address assigned tcpdump: listening on vif6.0, link-type EN10MB (Ethernet), capture size 96 bytes 14:49:40.833997 arp who-has 192.168.60.35 tell 192.168.60.133 14:49:41.833314 arp who-has 192.168.60.35 tell 192.168.60.133 14:49:42.833309 arp who-has 192.168.60.35 tell 192.168.60.133 So the VM is sending out out an arp who-has packet when I try to ssh to 192.168.60.35. I think that this means the setup within the VM is ok and that this is an issue on the host system. If I run tcpdump with the interface of br0 then I don't see these arp packets. My thought here is that the packets are being blocked before going on to the bridge somehow. I tried adding an iptables rule to resolve this: -A FORWARD -m physdev --physdev-is-bridged -j ACCEPT but it didn't work. I also tried the following: /sbin/sysctl -w net.bridge.bridge-nf-call-ip6tables=0 /sbin/sysctl -w net.bridge.bridge-nf-call-iptables=0 /sbin/sysctl -w net.bridge.bridge-nf-call-arptables=0 /sbin/sysctl -w net.ipv4.ip_forward=1 which had no impact. Is it obvious to somebody who has more experience than me what I'm missing here? Should vif6.0 have the same MAC address is eth0 in the vm? Do I need more rules in my iptables? Thanks for any help!

  Read the article

• All nework interfaces hang for seconds while one interface goes up/down

  - by user3698377

  I am building a client/server application that uses several network interfaces in parallel for redundancy, and I have noticed that while one network interface goes down or goes up, the communication on other interfaces hangs for several seconds. I could reproduce this behavior without my application in a simple way: there are 2 interfaces available on computer 1 ( Ethernet and WiFi ) ping from computer 2 the IP address of the Ethernet connection of computer 1 disconnect the WiFi of computer 1 ping hangs for seconds, and then the packets are traveling again between the 2 computers. The hanging happens as well if I turn back on the WiFi connection on computer 1. It happens as well if I ping the WiFi IP, and turn off/on the Ethernet connection ( or unplug/plug the cable). I am using Linux Ubuntu 12.04 on both computers. Any ideas why is this happening, and if / how can it be avoided?

  Read the article

• Connect wired-only devices to a remote wireless access point?

  - by billpg

  Hi everyone. In building A, I have a Netgear wireless access point using WPA2. Works great, no problems. In building B, I have some devices that only have wired Ethernet ports. They can't see my access point. What I need is a gizmo that connects over-the-air to my access point in building A, talks WPA2, and converts the packets to and from a wired Ethernet port. Netgear-access-point in building A      (WPA2 WiFi) Wireless bridge device          <-- Looking for this.      (Cat5 ethernet) My devices in building B. I've looked for devices on Amazon, but the descriptions are infuriatingly unclear. It says it supports WPA2, but does it support it as a client? Grrr... Any recommendations please?

  Read the article

• Is to possible to achieve the SATA II's 3Gbps (375MBps) between home network storage and home computers?

  - by techaddict

  Gigabit ethernet only has 1Gbps (125MBps), whereas SATA II has up to three times that rate. Is it possible to achieve the rate of three times Gigabit ethernet connection which is SATA II speeds, between home network storage and the laptops and desktops with SATA II hard drives? If so, how? Or, is the limitation of a gigabit ethernet port on the laptops the limitng factor, making 1000Gbps the fastest practical transfer speed possible? (practical, meaning that without taking apart the laptop and doing physical modifications like branching a SATA II transfer cable, etc.) -- I just realized -- wouldn't a USB 3.0 cable do the trick? Since USB 3.0 can reach up to 675MBps?

  Read the article

• CARP: two machines think they're the master, but only on one interface

  - by Conor McDermottroe

  I have two machines, each configured identically as a firewall/load balancer for a busy website. I have set them up with CARP and pfsync on both the internal and external interfaces. The internal interface is behaving as expected (primary listed as MASTER and secondary listed as BACKUP) On both machines, the network interfaces are as follows: em0 - External interface bge0 - Internal interface bge1 - Crossover connection between both machines carp0 - Shared external interface for CARP carp1 - Shared internal interface for CARP I've rewritten the IP addresses and MAC addresses below. The networks are as follows: 10.0.1.0/24 - External network 10.0.2.0/24 - Internal network 10.0.3.0/24 - Crossover network Here's the output from ifconfig on the primary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.10 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.10 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.10 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.11 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 0 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: MASTER vhid 2 advbase 1 advskew 0 And here's the /etc/rc.conf excerpt from the primary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.10 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.11" And here's the output on the secondary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.11 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.11 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.11 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.10 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 20 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: BACKUP vhid 2 advbase 1 advskew 20 And here's the /etc/rc.conf excerpt from the secondary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.11 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] advskew 20 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] advskew 20 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.10" What I don't understand is, the carp status on carp0 is MASTER on both machines when the status on carp1 is as it should be (MASTER on the primary and BACKUP on the secondary). What am I missing? Where should I be looking for clues?

  Read the article

• CentOS connect to the internet

  - by Delirium tremens

  I installed CentOS, but it didn't automatically connect to the internet. Is that the normal behavior? I have Ethernet Broadband Router DI-604 and WebStar DPX2203 series Cablemodem with EMTA . What should I do to connect to the internet? Update: A cousin told me my ethernet adapter or network board will depend on my motherboard. My computer upgrade document says the motherboard is gigabyte video onboard. I heard gigabyte's network adapters are Gigabit or Realtek. In CentOS, System - Administration - Network - New - Ethernet, first, only "Other Network Board" was listed, so I selected it and clicked Next, then there wasn't Gigabit, but there was Realtek, so I selected Realtek. I heard with Net Virtua selecting dhcp the things first answered asked me to tell first answerer are automatically configured. So I tried Realtek with dhcp, but it still didn't work.

  Read the article

• iSCSI - what's faster?

  - by Unplugme71

  I have a DroboPro that is currently connected to a GS748TS switch. Also connected to the switch is a server and few workstations. Which method would be better in performance? Add a NIC to the server. Direct connect the DroboPro via iSCSI to the new NIC. Add a NIC to the server. Create a dedicated VLAN for the new NIC and Drobo. Add a NIC to the server and attach it to a separate switch. DroboPro connects to the switch. Becomes a private network, similar to a VLAN. DroboPro has a single ethernet connection. Server has a single ethernet connection (currently). Workstations each have a single ethernet connection.

  Read the article

• Slow download speeds on MacBook Pro

  - by Austin

  Just as the title says, I am getting very low download speeds on my MacBook Pro. I did a speed test at speedtest.net, and am getting 7 MbPS down, .5 up. However, I can only seem to get 270 KB PS max (averaging 100 K), whether on my school's network or on my home network, wired or wireless. I am on Mac OS X 10.5.8, with Google Chrome. My ethernet settings (under System Preferences - Network - Ethernet Connection - Advanced - Ethernet) are set to "Configure Automatically", "Speed: 100TX", "Duplex: full-duplex, flow-control", and "MTU: Standard (1500)". As far as I can tell, there are no throttles or anything between here and the ISP, so... Any ideas on why I'm getting such low download speeds?

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• Sharing internet connection from Windows XP using wi-fi router

  - by Darius

  Hi, I have an network configuration like: Ethernet cable from ISP connected to Windows XP machine, configured with static IP 192.168.0.3 Another ethernet connection from 2nd Windows XP machine's network adapter to a Wi-Fi router (D-Link Airport G+) XP set to "Share internet connection", the 2nd adapter configured as static to 192.169.0.1 D-Link Airport Wi-Fi router also configured as "static connection", it's IP set to 192.169.0.2, default gateway set to 192.169.0.1. Network mask everywhere is 24. Laptop computer connected with the router with static IP 192.169.0.3 The problems are: XP machine sees the router (it's able to ping it and access it via the web admin tool) The router somehow cannot PING the XP machine (using the tool provided by the web-based admin tool) The laptop computer cannot ping anything and cannot be pinged The router is only accessible when the ethernet cable is connected with a router's 1-4 LAN port, when I connect it via "WAN" port (which I believe is the proper one) it's not visible from the XP machine If you have similar experience with configuring a network like this I would really appreciate your help. I cannot use the Wi-Fi router with the ISP cable itself.

  Read the article

• Laptop connects to other network but not to my home wireless

  - by Nilesh

  My home network's wireless SSID is say "XYZ" I also have an ethernet wire from the same router. I have two laptops A and B Earlier both A and B were able to connect to my home internet through the ethernet and wireless. Suddenly, the laptop B can no longer connect to XYZ or through ethernet. When I do plug the wire, i get the connection icon all green but when I try to access any web page it errors out (page not found) But strangely laptop B connects to my neighbours wireless SSID "ABC". I have also tested laptop B with other networks and it connects fine. Laptop A and many other devices still connect fine with my home wireless "XYZ" Strange thing is when my laptop B connects wireless through XYz, it gets the IP address but then none of the browsers (chrome,firefox, IE) can show any web pages. What settings should I be checking on laptop B that is preventing it to connect to my home internet. Thank you

  Read the article

• Configuring Wireless Network

  - by Vinod K

  I have vyataa router on VMware with 2 interfaces eth0 and eth1 eth0 is facing the internet eth0 is in Nat mode with dhcp on eth1 is in bridged mode with my ethernet with ip 10.0.2.34/24 The ethernet card is at ip 10.0.2.95/24 i have defined the nat rule. Hence internet is available at eth1 too. Now i am connecting a wireless router at "eth1" iball router, I have connected the router using a cable to the ethernet interface of my laptop. I have configured the WAN connection type as "Static IP" and given "10.0.2.34/24" All the clients that connect using wireless router cannot connect to the internet though. Could anyone provide me a solution for this.. Thank You!!

  Read the article

• ipconfig /release not working, why?

  - by barlop

  ipconfig /release is not working, why is that? here is a sequence where I put my cable in get an IP, try ipconfig /release and it tells me it can't release wireless, but there is no wireless connection. i'm just trying to release the wired one. C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Fine so I plug my cable in C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 0.0.0.0 Subnet Mask . . . . . . . . . . . : 0.0.0.0 Default Gateway . . . . . . . . . : C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.1.8 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.254 Fine so from above, it clearly has an iP C:\>ipconfig /release Windows IP Configuration No operation can be performed on Wireless Network Connection while it has its me dia disconnected. C:\>

  Read the article

• Computer never connects to the internet automatically on startup?

  - by RawR Crew

  I have my Windows Vista laptop connected directly to the router via an ethernet cable, and every time I switch the computer on, the computer cannot connect to the internet. It comes up as limited or no connectivity, I am assuming because it has not been assigned an IP address by the router - not too sure if this is right. The problem is usually fixed either by performing a repair through the networking control panel or removing and re-inserting the ethernet cable. It will also connect without doing any of these if the computer is left idle for about 20 minutes. It will connect fine wirelessly without the need for any of this, however I would prefer to connect via the cable. Any ideas how I can fix this? I have replaced the ethernet cable and router already (identical model) but these haven't helped. Thanks for any help on this.

  Read the article

• Wi-fi signal with keeping the internet cable

  - by daGrevis

  So the situation is that I have Ethernet cable which provides internet to my computer. Thing I want is to have wi-fi connection in my house and Ethernet cable (like I have before) to use for my PC. I will use wi-fi for my laptop and mobile phone. I think I need router for that and I'm looking at Asus RT-N16 (suggested in Coding Horror) for it, but I am not sure. Is it the right thing for me and I will be able to get wi-fi signal and keep the Ethernet cable? I guess the system will be that current cable goes into router, router provides wi-fi signal and gives back new cable... or something like that. Thanks in any advice! And sorry if topic isn't in right site.

  Read the article

• Laptop connects to other network but not to my home wireless

  - by Nilesh

  My home network's wireless SSID is say "XYZ" I also have an ethernet wire from the same router. I have two laptops A and B Earlier both A and B were able to connect to my home internet through the ethernet and wireless. Suddenly, the laptop B can no longer connect to XYZ or through ethernet. When I do plug the wire, i get the connection icon all green but when I try to access any web page it errors out (page not found) But strangely laptop B connects to my neighbours wireless SSID "ABC". I have also tested laptop B with other networks and it connects fine. Laptop A and many other devices still connect fine with my home wireless "XYZ" Strange thing is when my laptop B connects wireless through XYz, it gets the IP address but then none of the browsers (chrome,firefox, IE) can show any web pages. What settings should I be checking on laptop B that is preventing it to connect to my home internet. Thank you

  Read the article

• Establish direct cable connection between Windows 8 PCs in home network

  - by Marie. P.

  I'm running two PCs, a desktop and a laptop with Windows 8 Release Preview ("Build 8400"). They are connected to the same router in infrastructure mode, thereby having wireless internet. Due to often file synchronization between the machines I want to establish a cable connection that allows direct file transfer, without needing to use the wireless. When I plug in the cable (normal, not cross-over), I see in "Control Panel\Network and Internet\Network Connections": "Ethernet - unidentified Network" on both PCs. Transferring a file between both still only uses the WiFi via the Router. I noticed that when turning off the wifi on one PC, I can set up a shared internet connection that will work via Ethernet-cable, but since sometimes only one PC runs, sometimes the other one, I do not want to have the internet of one machine to be dependent on the other one being switched on. I do not have a crossover-cable, but since I did connect the PCs already successfully (just without both being on the internet), I'm sure that this should also work with a normal ethernet cable.

  Read the article

• Change ip route metric

  - by notphunny

  I'm constantly switching between eth0 and wlan0 interface on my archlinux because I often change OpenWrt fw images on my second router (which isn't connected anywhere). So I have problem with my routes when I'm connected to my wlan and want to connect with Ethernet to my router. Both routers are on 192.168.1.1/24 and after connecting to my Ethernet profile eth0 route becomes default one (which is ok for the time), because of smaller metric I guess. So I'm interested, how can I change routes metric so my applications can be connected to the internet (through out wlan)? Maybe there is solution not to use Default Gateway on Ethernet profile, however I still want to know how to change metric. Or default route if there are more then one.

  Read the article

• Wireless doesn't work on a Lenovo V570

  - by Stephen

  I've had Ubuntu installed on my HD for about 3 months but ever since I ran into this wireless issue I kinda lost my lust of Ubuntu. I have zero experience getting around with/ using the console command. I have a Lenovo V570. I got the driver update for the broadcom networking card via the Additional Drivers application but that did nothing. I love the look and feel of using Ubuntu but I have no technological experience for the matter. Any help would be awesome. When I scan for wireless connections while in Ubuntu, my computer picks up nothing, while on Win7 it will pick up the handful of wireless networks around my area. My wired connection is fine, but the use of not having wireless on a laptop is rather contradictory to it as a feature. Cheers! Also, I just installed 11.10, if that helps any. Yes, I used the search before I posted this, but again I have ZERO understanding of the command stuff and need a meat and potatoes answer(s). stephen@ubuntu:~$ sudo lshw -class network [sudo] password for stephen: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f1900000-f1903fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: 06 serial: f0:de:f1:63:98:14 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.1.78 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff stephen@ubuntu:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• Wireless will not connect

  - by azz0r

  Hello, I have installed Ubuntu 10.10 on the same machine as my windows setup. However, it will not connect to my wireless network. It can see its there, it can attempt to connect, yet it will never connect. It will keep bringing up the password prompt everyso often. I have tried turning my security to WEP, I ended up turning it back to WPA2. It is set to AES (noted a few threads on google about that). Can you assist? I would love to dive into Ubuntu, but without the internet its pointless. --- lshw -C network --- *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 00:1d:92:ea:cc:62 capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.020.00-NAPI duplex=half latency=0 link=no multicast=yes port=twisted pair resources: irq:29 ioport:e800(size=256) memory:feaff000-feafffff memory:f8ff0000-f8ffffff(prefetchable) memory:feac0000-feadffff(prefetchable) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:15:af:72:a4:38 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bgn --- iwconfig ---- lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Wuggawoo" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Tx-Power=9 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on --- cat /etc/network/interfaces ---- auto lo iface lo inet loopback logs deamon.log --- Jan 19 04:17:09 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:11 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): association took too long. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 5 -> 6 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): asking for new secrets Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 6 -> 4 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 4 -> 5 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): connection 'Wuggawoo' has security, and secrets exist. No new secrets needed. Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'ssid' value 'Wuggawoo' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'scan_ssid' value '1' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'key_mgmt' value 'WPA-PSK' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'psk' value '<omitted>' Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_engine_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_module_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: set interface ap_scan to 1 Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:13 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:23 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:24 ubuntu AptDaemon: INFO: Initializing daemon Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:25 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:27 ubuntu NetworkManager: <info> wlan0: link timed out. --- kern.log --- Jan 19 04:18:11 ubuntu kernel: [ 142.420024] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:13 ubuntu kernel: [ 144.333847] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:13 ubuntu kernel: [ 144.539996] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:13 ubuntu kernel: [ 144.750027] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:14 ubuntu kernel: [ 144.940022] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:25 ubuntu kernel: [ 155.832995] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:25 ubuntu kernel: [ 156.030046] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:25 ubuntu kernel: [ 156.230039] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:25 ubuntu kernel: [ 156.430039] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out --- syslog --- Jan 19 04:18:46 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:18:48 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:18:48 ubuntu kernel: [ 178.833905] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:48 ubuntu kernel: [ 179.030035] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:48 ubuntu kernel: [ 179.230020] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:48 ubuntu kernel: [ 179.433634] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out lspci and lsusb lspci -- 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:00.0 VGA compatible controller: nVidia Corporation G80 [GeForce 8800 GTS] (rev a2) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 03:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller -- lsusb -- Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 004 Device 002: ID 045e:0730 Microsoft Corp. Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 13d3:3247 IMC Networks 802.11 n/g/b Wireless LAN Adapter Bus 002 Device 002: ID 0718:0628 Imation Corp. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 046d:08c2 Logitech, Inc. QuickCam PTZ Bus 001 Device 002: ID 0424:2228 Standard Microsystems Corp. 9-in-2 Card Reader Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub With no security on my router I still can't connect, I get: Jan 19 15:58:01 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: WPS-AP-AVAILABLE Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Association request to the driver failed Jan 19 15:58:02 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 15:58:05 ubuntu NetworkManager: <info> wlan0: link timed out. Jan 19 15:58:07 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connec

  Read the article

• Internet suddenly stopped working

  - by user95629

  I was using NoMachine to access Ubuntu 11.10 when suddenly the internet on Ubuntu stopped working. Now Ubuntu doesn't recognize the internet at all (including locally). Symptoms: Doesn't recognize the fact that there is an ethernet cable attached. (I've tried switching cables, didn't work.) GUI says "No network devices available" Can't ping external IP addresses. Tried changing /etc/network/interfaces to eth1 instead of eth0 but it didn't work. ifconfig provides no output relating to eth0. When I type "/etc/init.d/networking restart" it tells me "Cannot find device 'eth0'/Failed to bring up eth0." The network settings had used a static IP address prior to the crash. I don't know why it won't recognize the ethernet (I think this is the fundamental problem, but I might be wrong) and why it stopped working so suddenly--I haven't installed any updates lately. Any ideas? Any more information I should provide? EDIT: lspci recognizes the Ethernet controller; netstat does not. lspci calls it "Intel Corporation Device 0000"

  Read the article

• Delete eth0 avahi from the ifconfig list

  - by sai

  Hello this is the response I get from ifconfig. Now I have two eth0 things being showed up. I need to delete the second one which says eth0:avahi. I posted my ifconfig's response on a site as I has problem using wired internet, and they suggested to remove the eth0 avahi, to get internet. But I am a newbie to linux networking and have no idea how to delete this. response for ifconfig eth0 Link encap:Ethernet HWaddr 18:a9:05:22:cd:f9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:28 Base address:0x4000 eth0:avahi Link encap:Ethernet HWaddr 18:a9:05:22:cd:f9 inet addr:169.254.10.43 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:28 Base address:0x4000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:796 errors:0 dropped:0 overruns:0 frame:0 TX packets:796 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:64016 (64.0 KB) TX bytes:64016 (64.0 KB) wlan0 Link encap:Ethernet HWaddr 00:26:82:3c:ac:27 inet6 addr: fe80::226:82ff:fe3c:ac27/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:52142 errors:0 dropped:0 overruns:0 frame:0 TX packets:30404 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:60816983 (60.8 MB) TX bytes:4160159 (4.1 MB)

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >