Search Results

Search found 8056 results on 323 pages for 'external'.

Page 26/323 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33 | Next Page >

Ubuntu doesn't "see" external USB Hard Disk

- by Mina Michael

It's NTFS. It's USB2. I'm using Ubuntu 13.04. It works perfectly fine on Windows (which excludes cable and hardware problems). I have two Ubuntu computers and it's not detected on either. It's about 500 GB. Edits: Following the first link, I input sudo lsusb in a terminal; before and after connecting the HDD. The difference was Bus 001 Device 012: ID 14cd:6116 Super Top M6116 SATA Bridge. There it is! ("sata bridge" used to appear in a windows notification when I plugged in the HDD in!). ...This means that Ubuntu detects it but is it not mounting it? I tried this: sudo mount /dev/sdb1 /mnt But gives this: mount: special device /dev/sdb1 does not exist I also tried: sudo mount /dev/sdc1 /mnt but it stays with no output forever. I left it in background for about 30 min.s. sudo fdisk -l gives out this: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xa42d04a3 Device Boot Start End Blocks Id System /dev/sda1 63 80324 40131 de Dell Utility /dev/sda2 * 80325 102481919 51200797+ 7 HPFS/NTFS/exFAT /dev/sda3 263874558 312580095 24352769 5 Extended /dev/sda4 102481920 263872511 80695296 7 HPFS/NTFS/exFAT /dev/sda5 263874560 310505471 23315456 83 Linux /dev/sda6 310507520 312580095 1036288 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x5822aaea Device Boot Start End Blocks Id System /dev/sdc1 2048 976769023 488383488 7 HPFS/NTFS/exFAT The part below "Partition table entries are not in disk order" takes about 5 minutes to appear. The outputs of ls /dev/ | grep sd before and after connecting the HDD: before: sda sda1 sda2 sda3 sda4 sda5 sda6 ,after: sda sda1 sda2 sda3 sda4 sda5 sda6 sdd sdd1 The second output has the lines sdd and sdd1 different from the first one. IT SHOWED THE FILES!! The command sudo mount /dev/sdd1 /mnt worked after I typed in sudo fdisk -l!!! Thanks a million!! :) :)

Read the article
SSH from external network refused

- by wulfsdad

I've installed open-ssh-server on my home computer(running Lubuntu 12.04.1) in order to connect to it from school. This is how I've set up the sshd_config file: # Package generated configuration file # See the sshd_config(5) manpage for details # What ports, IPs and protocols we listen for #Port 22 Port 2222 # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key HostKey /etc/ssh/ssh_host_ecdsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH #LogLevel INFO LogLevel VERBOSE # Authentication: LoginGraceTime 120 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords #PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding no X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net Banner /etc/sshbanner.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. UsePAM yes #specify which accounts can use SSH AllowUsers onlyme I've also configured my router's port forwarding table to include: LAN Ports: 2222-2222 Protocol: TCP LAN IP Address: "IP Address" displayed by viewing "connection information" from right-click menu of system tray Remote Ports[optional]: n/a Remote IP Address[optional]: n/a I've tried various other configurations as well, using primary and secondary dns, and also with specifying remote ports 2222-2222. I've also tried with TCP/UDP (actually two rules because my router requires separate rules for each protocol). With any router port forwarding configuration, I am able to log in with ssh -p 2222 -v localhost But, when I try to log in from school using ssh -p 2222 onlyme@IP_ADDRESS I get a "No route to host" message. Same thing when I use the "Broadcast Address" or "Default Route/Primary DNS". When I use the "subnet mask", ssh just hangs. However, when I use the "secondary DNS" I recieve a "Connection refused" message. :^( Someone please help me figure out how to make this work.

Read the article
SEO and external sites that serve responsive images (like Re-SRC)

- by Baumr

Re-SRC is a tool that allows you to automatically serve responsive images for your website from their cloud servers. It delivers a new image file each time the browser window (viewport) is resized. To use it in your HTML when linking to an image, you would do the following: <img src="http://app.resrc.it//www.your-domain.com/img/img001.jpg"/> Some more background for SEO considerations: As an example, looking at their demo page's code, the src of the Arc de Triomphe photo — when the browser window is resized to be at a tablet-width — shows this particular file at it's widest. It is found under the following URL: http://app4-uk.resrc.it/s=w560,pd1/ro=h//www.resrc.it/img/demo/demo-image-1.jpg If the viewport is increased to desktop-width, then a smaller image is served in line with the design; see this URL: http://app4-uk.resrc.it/s=w320,pd1/ro=h//www.resrc.it/img/demo/demo-image-1.jpg If I change the viewport to be about half-way between those two, then the image's URL is: http://app4-uk.resrc.it/s=w240,pd1/ro=h//www.resrc.it/img/demo/demo-image-1.jpg In other words, I found that there is a separate file for every 10-pixel increment of the image width. Very cool for saving bandwidth on mobile devices and service responsive/retina images on others, but... Here are two problems I see for SEO: The img on your site, part of your semantic markup, will not be hosted on your site at all, or even a server you control. Any links to these images will pass on "link juice" to Re-SRC's site instead. You are serving a vast array of different image files to different people — some may link to one, others to another size. Then there's the question of what different search engine crawlers will see. Also: There seems to be no fallback option if their servers are down. Do you see any other concerns? Or, perhaps, do you not see those as concerns?

Read the article
iTunes lost my music after re-plugging my external harddisk

- by AskAboutGadgets.com

I am storing most of my music on an external hard disk and from time to time I need to unplug this disk. After reconnecting it to my computer and starting iTunes I noticed that the individual songs stored on the external drive are now lost (they have a little exclamation mark next to them). iTunes offers me to locate the songs one by one, but I have thousands of songs. Is there a better solution to reconnect my collection in iTunes?

Read the article
How to combine AWS and dedicated external servers?

- by rfw21

I have an extensive network of servers all currently hosted on AWS EC2. For reasons of cost I plan to gradually migrate to dedicated servers where possible. So: How can I best combine AWS and non-AWS servers in my network? Ideally, I should be able to assign internal IP addresses to the external servers, include them in AWS security groups and ensure that all private traffic between my AWS servers and external servers is secure.

Read the article
How Do External Links Help SEO?

Starting at the beginning because without search engines there would be no optimisation. Google was founded by two Stanford University students in 1996 as part of a doctoral research project by Larry Page and Sergey Brin.

Read the article
External Full HD monitor and Virtual Desktop Size

- by Stefan

I have two FullHD monitors attached to my ATI graphics card [2]. The resolution of both of them is detected properly without any modifications to /etc/X11/xorg.conf. I can run both of them in clone mode. However, when I try to run them next to each other, I got the following error: The selected configuration for displays could not be applied. If tried to fix this according to [1]. My xorg.conf now looks like this: Section "Module" Load "glx" EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 SubSection "Display" # The 1088 is the smallest multiple of 32 >= 1088 # see manpages Virtual 1920 1088 EndSubSection EndSection This does not seem to be parsed properly. After restarting X, I cannot set resolutions beyond 1600 or so any more. /var/log/Xorg.0.log gives: [ 15.676] (II) fglrx(0): Not using mode "1920x1080" (width too large for virtual size) [ 15.676] (II) fglrx(0): Not using mode "1680x1050" (width too large for virtual size) Are my modifications syntactically incorrect? According to the man page, it should be fine. Any ideas? OS: Ubuntu 11.10 64bit [1] http://askubuntu.com/a/75546/5023 [2] 01:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5700 Series]

Read the article
How to fend off external interuptions?

- by Demian Kasier

I want to keep my focus at work, but I am constontly interupted. examples: - the boss asks something to the whole team. - a coleague asks something about a piece of code I wrote - something funny on the radio - smalltalk among coleages with a joke in between. - ... As extra info: We are a team of 6 developpers in one room, with sales and suits constantly coming over to ask and tell us things we must and mustn't do. So how do you keep you focus and attention to your work? so you can get some things done, instead of answering to everyone and everything that interupts you?

Read the article
Configure Apache to use external proxy for internet connection

- by warpech

In my application I am using following rewrite rule: RewriteRule ^/ajax(.*) http://api.externalserver.com/$1 [P,QSA,L] You know what it does. Now the problem is that my corporate network requires me to use HTTP proxy for external internet connections. To ilustrate, this doesn't work: curl -v http://api.externalserver.com/login But this works: curl -v -x 11.22.11.22:8585 http://api.externalserver.com/login How can I make Apache use the corporate proxy for external internet requests?

Read the article
laptops with 5.1 surround sound card for external use and not internal [closed]

- by Jayapal Chandran

I want to buy a laptop with 5.1 sound card from which i should be able to connect my external 5.1 speakers for example creative inspire 5.1 or similar creative model speakers. Is this option available. It should be and i want suggestions or a list of manufacturers with such option. My friend got one but he said it cannot be use with external speakers it is just built in 5.1 speakers. So i am asking this question.

Read the article
Avoid External Dependencies in SQL Server Triggers

I sometimes want to perform auditing or other actions in a trigger based on some criteria. More specifically, there are a few cases that may warrant an e-mail; for example, if a web sale takes place that requires custom or overnight shipping and handling. It is tempting to just add code to the trigger that sends an e-mail when these criteria are met. But this can be problematic for two reasons: (1) your users are waiting for that processing to occur, and (2) if you can't send the e-mail, how do you decide whether or not to roll back the transaction, and how do you bring the problem to the attention of the administrator?

Read the article
W520 External monitor setup with Ubuntu 12.10

- by user108372

I just installed a fresh Ubuntu 12.10 64-Bit Desktop on my Lenovo W520. It looks like there are a lot of challenges around making it work with out of the box Nouveau drivers or propriety Nvidia drivers or Intel GPU. I looked at couple of notes on how to make it work with Bumblebee with Optimus Nvidia. None of them seems to work for 12.10. Anybody has a solid answer on this? It seems like a lot of people are suffering from this. Here is my xrandr output. Let me know if you need any additional information. Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 8192 x 8192 LVDS1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 344mm x 193mm 1920x1080 60.0*+ 59.9 50.0 1680x1050 60.0 59.9 1600x1024 60.2 1400x1050 60.0 1280x1024 60.0 1440x900 59.9 1280x960 60.0 1360x768 59.8 60.0 1152x864 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) Thanks, Sef

Read the article
SQL Server Semantic Search to Find Text in External Files

Sometimes it is necessary to search for specific content inside documents stored in a SQL Server database. Is it possible to do this in SQL Server? Can I run T-SQL queries and find content inside Microsoft Word files? Yes, now with SQL Server 2012 you can do a semantic search. 12 essential tools for database professionalsThe SQL Developer Bundle contains 12 tools designed with the SQL Server developer and DBA in mind. Try it now.

Read the article
Juniper router dropping pings to external interface

- by Alexander Garden

My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

Read the article
client flips between internal and external IP addresses??

- by jmiller-miramontes

I have what seems like a not-particularly-complicated home network, all things considered: a DSL line comes in to a modem/router, which goes off to a switch, which supports a bunch of machines. My machines live in a 192.168.0.x address space; however, I'm running some public servers on the network, so I have a block of 8 (5, really) static IP addresses that are mapped to the servers by the router. The non-servers get 192.168.0.x addresses via NAT; some machines have static addresses and some get addresses from DHCP. Locally, I'm running a DNS server (named) to map between the domain names and the 192.168 address space. Somewhat messy, but everything basically works. Except: One of my local non-server clients occasionally switches from its internal address to its external address. That is, if I check the logs of a website I'm running internally, the hits coming from this client sometimes show up with the internal 192.168 address, and sometimes with the external (216.103...) address. It will flip back and forth for no apparent reason, without my doing anything. This can be a problem in terms of how the clients interact with the way I have some of the clients' SSH systems configured (e.g., allowing access from the internal network but not the external network), but it also Just Seems Wrong. I will confess that I'm kinda skating on the very edge of my networking competence here, but I can't for the life of me figure out what's going on. If it helps, the client in question is running Mac OS X / 10.6; its address is statically assigned, is not one of the five externally-accessible addresses, and gets its DNS from (first) the internal DNS server and (second) my ISP's DNS servers. I can't swear that none of the other NAT clients are also showing this problem; the one I'm dealing with is my everyday machine, so this is where I run into it. Does anybody out there have any advice? This is driving me crazy...

Read the article
Nvidia GTS 360M in Asus laptop shuts off when gaming on external display

- by mr odus

I have had this problem on my Asus G51j Intel I5, Nvidia GTS360M graphics card. Just updated the drivers to latest off Nvidias site. Most games I play, If I hook it up through an external monitor(this happens whether it's HDMI or VGA). The laptop hard shuts down after about 20 minutes, give or take. This tends to happen on more graphically intense games like Call of dutys, bioshock. I'm running Windows 7, latest nvidia drivers. Games work fine on my laptops screen, and Movies, general computing work fine on the external displays. The laptop always sits on a cooling pad and the latest time was in front of my AC unit, I ran heatfan or whatever the heat tracking software was, and my temperatures were normal through a shut down. This has been happening for the life of the laptop. I dont play very many games, and even fewer on an external monitor, so this issue doesnt come up much Is it possible I have a faulty graphics card? Is there anything else I can try?

Read the article
Using native resolution on external display results in stretched, out of bounds image

- by Roni Yaniv

I have an HP min 311 netbook with Windows XP, which I've connected to a Samsung SyncMaster 2043BW display via the supplied analog cable. The external display's native res is 1680x1050, which the netbook's ION GPU supports. I've configured the external display as the single display (no cloning or any such fancy stuff). However, once I set the native res, the image just stretches out. It looks squashed, and it goes outside the monitor's edges. In contrast, lower resolutions manage to stay within the monitor's display edges, though obviously they are skewed in some way (vertically or horizontally). BTW, the only res which seems to be displayed relatively clearly (it's the least blurry) is 1280x720. I tried looking all over the web for an explanation/advice but could not find any. I already played with the settings on the external display itself several times. So either it's not that, or I missed something. Has someone run into this issue? I need help.

Read the article
Sharing a folder with Nautilus and NTFS external drive gets errors

- by TheLQ

I am trying to share a folder in Lubuntu over a network that's on an external NTFS drive. Due to the system that I have (rotating backup disks) this is probably the second time that the drive would of been mounted. Its manually mounted with a simple (for example) mount /dev/sdb1 /media/BACKUP On an internal NTFS disk I have successfully setup a network share and can access it. However on the external disk I can't from any other Windows computer. When setting up the share Nautilus said that it needs to change the other's permissions to allow for other users to write. However afterwords its still blank. Changing it to Read and Write just changes back to blank. Chowning the entire /media folder recursively and trying didn't work. Running PCManFM as root and changing didn't work. Adding "public=yes" to smb.conf and restarting didn't work. I'm out of idea's on what to do. What's weird is that it worked just fine on an internal NTFS disk, so why not the external one? Any solutions need to be able to managed inside of a gui (preferably Nautilus) as the person managing the machine isn't as tech savvy. Thanks

Read the article
Juniper router dropping pings to external interface

- by Alexander Garden

My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

Read the article
Explorer.exe hangup during move large file into external drive

- by PiotrK

During move large files (700mb+) to external drive formated NTFS via USB 3.0 I've noticed strange things about explorer.exe (I am using Windows 7 up to date) Sometimes after move file the explorer get stuck (ie. it can happen after few files during move of several large files) - moving window freeze and I am unable to kill explorer (via taskmgr, or cmdline TASKKILL). In command line I've got something like this (taskmgr shows that explorer.exe is still running - I've got the same PID every time I try to kill it and no diagnostic message): C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. If I try to run another explorer.exe process at this point, I got desktop icon and start bar back but I cannot open any explorer window After few minutes explorer.exe finally dies and I am able to rerun it without rebooting File that I moved have two copies - one local and one on the external drive (the original file wasn't delete after move); Both copies seems to contain the same data (same length and CRC info) If this happen during move of multiply files, only some files are moved and one of them have two copies (both locally and on the external drive) What can I do to fix those explorer hangs? Added: The same problem exist when copying files, it hangsup between large files Similar problem exist when I tried to use TotalCommander (x64): copying paused at 80% of one of files, TC didn't hung up (but clicking cancel in copying dialog box doesn't have any effect). During this pause I can't kill TotalCmd.exe just like Explorer.exe Added (2): This problem seems to disappear when I use 32 bit applications (like TotalCommander (x86) ), but I need to do more testing to be sure of this Added (3): There are several errors in event log, source: disk, id: 11, qualifiers: 49156, task: 0, level: 2, keywords: 0x80000000000000 (This may be important, and I forgot to mention this): Main disk is encrypted via Truecrypt (boot-in password)

Read the article
Set document root for external subdomain (A Record) via htaccess

- by 1nsane

I have a managed server (unable to control apache settings) with the default document root of: /var/www I have a web app running in: /var/www/subdomains/app/webroot I have a dedicated domain managed by the host that has the aforementioned webroot which works perfectly. I would like to allow externally provisioned domains to point to the server/web app via A Record config. If I access the site via IP, it takes me to the index located in /var/www. I would like to configure the .htaccess in my /var/www directory to rewrite requests from the external subdomain to the /var/www/subdomains/app/webroot directory. I've done so using the following rules: RewriteCond %{HTTP_HOST} external\.domain\.com$ [NC] RewriteRule ^(.*)$ /var/www/subdomains/app/webroot/index.php?url=$1 [L,QSA] When accessing external.domain.com, the app loads properly, but the paths to things like CSS files, images, etc. are prefixed with "/subdomains/app/", causing broken links. I've tried changing the RewriteBase (both in /var/www and /var/www/subdomains/app/webroot), as I believe that's what it's designed for - but no luck. Any ideas? FYI the app is built on CakePHP. Thanks

Read the article
how to i lock a Harddrive to a certain drive letter

- by Memor-X

i have an external hard drive that i have set to Drive F which on it contains some programs that i have shortcuts on the desktop how i have a second external hard drive which i store my music on which is auto assigned to Drive E, due to someone thinking that Australians love to have f** wings on power plugs for hard drives while power boards have each socket close together i can have both of these hard drives set at the same time my music hard drive i normally only plug up when i sync music to my ipod but on occasion when i unplug my music hard drive and plug my old one back in or at times when i turn on my computer with the music hard drive in, turn off my computer and turn it back on with my old hard drive it's drive letter gets switched to E i get annoyed having to always go into disk management and change the drive letter back to F when this happens so i am wondering if I can lock my hard drive to always be F, if anything else tries to be F it can fail for all i care If there is a batch file i can use that'll go though all the steps of Disk Management to change a drive's letter, that way i can set it up in the startup folder

Read the article
Installing XP through USB-to-IDE/SATA connector?

- by overtherainbow

Hello To help someone reinstall a corrupt XP install on his IDE or SATA drive in a older desktop box (hence no Vista/W7), I was thinking of asking him to bring his harddrive and meet at Starbucks, and I would install a brand new XP by connecting it to my laptop, and booting it up with the XP install CD. If someone's already used a USB-to-IDE/SATA connector such as this one by Sabrent: Does the XP CD accept installing Windows to an external IDE/SATA through USB? Does USB 2.0 provide enough power to run an external IDE/SATA drive, or do I need to provide the drive with its own power (in which case, how?)? Thank you.

Read the article
How can I quickly change display settings from dual monitor to single monitor on laptop?

- by Daren Thomas

I have my laptop (running Windows XP SP3) at work hooked up to an external monitor. Whenever I unplug the external monitor (time to go home!) I have to manually change the display settings. This takes time and involves a lot of clicks. Is there a way to automate changing these settings? I'm thinking of a hotkey solution or a little application that I can start with Launchy to toggle between two profiles. I use the MultiMon tool for "extending" the taskbar to the second monitor - will I have to give that up?

Read the article
How can I quickly change display settings (dual monitor setup / single monitor setup on laptop)?

- by Daren Thomas

I have my laptop (running Windows XP SP3) at work hooked up to an external monitor. Whenever I unplug the external monitor (time to go home!) I have to manually change the display settings. This takes time and involves a lot of clicks. Is there a way to automate changing these settings? I'm thinking of a hotkey solution or a little application that I can start with Launchy to toggle between two profiles. I use the MultiMon tool for "extending" the taskbar to the second monitor - will I have to give that up?

Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33 | Next Page >