Search Results

Search found 12751 results on 511 pages for 'interface'.

Page 26/511 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• iptables forwarding to a dummy interface

  - by madinc

  Hi, I'm trying to accomplish the following: I have a box with a service listening on a dummy interface (say 172.16.0.1), udp port 5555. Now what I'd like to do is to take packets that arrive on interfaces eth0 (1.1.1.1:5555) and eth1 (2.2.2.2:5555) and forward them to the service on the dummy interface, and have replies go back to clients out the same physical interface they came in. Clients must think they're talking to 1.1.1.1:5555 or 2.2.2.2:5555. I think I need a mix of iptables rules and packet marking, plus some iproute rules (if it's possible at all). What I tried is to catch packets coming in from eth0 and eth1, udp port 5555, and mark them with 1 and 2 respectively, and --save-mark in the connmark. Then I used a DNAT to 172.16.0.1. The service seems to be getting the packets. Now I'm not sure how to do the reverse. It seems that for packets originating from the box, you can't do anything before the routing decision, but that would be the place to restore the marks, and thus make a routing decision based on those. Here's what I have so far: iptables -t mangle -A PREROUTING -d 1.1.1.1 -p udp --port 5555 -j MARK --set-mark 1 iptables -t mangle -A PREROUTING -d 2.2.2.2 -p udp --port 5555 -j MARK --set-mark 2 iptables -t mangle -A PREROUTING -d 1.1.1.1 -p udp --port 5555 -j CONNMARK --save-mark iptables -t mangle -A PREROUTING -d 2.2.2.2 -p udp --port 5555 -j CONNMARK --save-mark iptables -t nat -A PREROUTING -m mark --mark 1 -j DNAT --to-destination 172.16.0.1 iptables -t nat -A PREROUTING -m mark --mark 2 -j DNAT --to-destination 172.16.0.1 # What next? As I said, I'm not even sure it can be done. To give a bit of background, it's an old OpenVPN installation that cannot be upgraded (otherwise I'd install a recent version that supports multihoming natively). Thanks for any help.

  Read the article

• Vyatta masquerade out bridge interface

  - by miquella

  We have set up a Vyatta Core 6.1 gateway on our network with three interfaces: eth0 - 1.1.1.1 - public gateway/router IP (to public upstream router) eth1 - 2.2.2.1/24 - public subnet (connected to a second firewall 2.2.2.2) eth2 - 10.10.0.1/24 - private subnet Our ISP provided the 1.1.1.1 address for us to use as our gateway. The 2.2.2.1 address is so the other firewall (2.2.2.2) can communicate to this gateway which then routes the traffic out through the eth0 interface. Here is our current configuration: interfaces { bridge br100 { address 2.2.2.1/24 } ethernet eth0 { address 1.1.1.1/30 vif 100 { bridge-group { bridge br100 } } } ethernet eth1 { bridge-group { bridge br100 } } ethernet eth2 { address 10.10.0.1/24 } loopback lo { } } service { nat { rule 100 { outbound-interface eth0 source { address 10.10.0.1/24 } type masquerade } } } With this configuration, it routes everything, but the source address after masquerading is 1.1.1.1, which is correct, because that's the interface it's bound to. But because of some of our requirements here, we need it to source from the 2.2.2.1 address instead (what's the point of paying for a class C public subnet if the only address we can send from is our gateway!?). I've tried binding to br100 instead of eth0, but it doesn't seem to route anything if I do that. I imagine I'm just missing something simple. Any thoughts?

  Read the article

• Separated virtual networks with same subnet range with 2 interface

  - by Coolpet

  I'm having some problems with routing with the following: I have a server with 2 interfaces. It has 1-1 alias contains the same subnet. the 2 interface is connected to 2 switch, which are separated from each other. Infrastructure: Eth0 192.168.16.2/20 Eth0:eth0 192.168.1.222/20 Eth1 192.168.32.3/20 Eth1:eth1 192.168.1.223/20 I have a PC which has the IP address: 192.168.1.3/24 The problem is the next: If PC is on subnet 1, I can ping it. If PC is on subnet 2, I can't ping it. traceroute shows the route is across 192.168.1.222 ping -I 192.168.1.223 192.168.1.3 is not working on subnet 2. arp entries show the MAC address belonging to the correct interface (eth1 on subnet 2) How can I force the server to look on both interface same ranged subnet for specific IP? It searches only in the first subnet. The routing table has these 2 entries: 192.168.0.0/20 dev eth0 proto kernel scope link src 192.168.1.222 192.168.0.0/20 dev eth1 proto kernel scope link src 192.168.1.223

  Read the article

• Can extension methods be applied to interfaces?

  - by Greg

  Hi, Is it possible to apply an extension method to an interface? (C# question) That is for example to achieve the following: create an ITopology interface create an extension method for this interface (e.g. public static int CountNodes(this ITopology topologyIf) ) then when creating a class (e.g. MyGraph) which implements ITopology, then it would automatically have the Count Nodes extension. This way the classes implementing the interface would not have to have a set class name to align with what was defined in the extension method.

  Read the article

• Items Created via IB are not being displayed

  - by Rohan

  Hello, This is what i have done so far, Made a Custom view added few objects, as shown below @interface CommUICustomSignInView : CommUICustomView { IBOutlet NSButton *pBtn; IBOutlet NSTextField *pTextField; NSTrackingArea *pTrackingArea; NSCursor *pPonitHandCursor; } Added all IBoutlet correctly, Now thru Interface builder constructed a Window controller interface builder in which added a custom view and provided this class name in the interface builder, I hope i could able to visualize you guys, now whenever i loaded this view, the item whatever i created by IB are not being displayed, Am i doing something wrong, or something missing,

  Read the article

• Simple Cisco ASA 5505 config issue

  - by Ben Sebborn

  I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

  Read the article

• Creating a dynamic proxy generator – Part 1 – Creating the Assembly builder, Module builder and cach

  - by SeanMcAlinden

  I’ve recently started a project with a few mates to learn the ins and outs of Dependency Injection, AOP and a number of other pretty crucial patterns of development as we’ve all been using these patterns for a while but have relied totally on third part solutions to do the magic. We thought it would be interesting to really get into the details by rolling our own IoC container and hopefully learn a lot on the way, and you never know, we might even create an excellent framework. The open source project is called Rapid IoC and is hosted at http://rapidioc.codeplex.com/ One of the most interesting tasks for me is creating the dynamic proxy generator for enabling Aspect Orientated Programming (AOP). In this series of articles, I’m going to track each step I take for creating the dynamic proxy generator and I’ll try my best to explain what everything means - mainly as I’ll be using Reflection.Emit to emit a fair amount of intermediate language code (IL) to create the proxy types at runtime which can be a little taxing to read. It’s worth noting that building the proxy is without a doubt going to be slightly painful so I imagine there will be plenty of areas I’ll need to change along the way. Anyway lets get started…   Part 1 - Creating the Assembly builder, Module builder and caching mechanism Part 1 is going to be a really nice simple start, I’m just going to start by creating the assembly, module and type caches. The reason we need to create caches for the assembly, module and types is simply to save the overhead of recreating proxy types that have already been generated, this will be one of the important steps to ensure that the framework is fast… kind of important as we’re calling the IoC container ‘Rapid’ – will be a little bit embarrassing if we manage to create the slowest framework. The Assembly builder The assembly builder is what is used to create an assembly at runtime, we’re going to have two overloads, one will be for the actual use of the proxy generator, the other will be mainly for testing purposes as it will also save the assembly so we can use Reflector to examine the code that has been created. Here’s the code: DynamicAssemblyBuilder using System; using System.Reflection; using System.Reflection.Emit; namespace Rapid.DynamicProxy.Assembly {     /// <summary>     /// Class for creating an assembly builder.     /// </summary>     internal static class DynamicAssemblyBuilder     {         #region Create           /// <summary>         /// Creates an assembly builder.         /// </summary>         /// <param name="assemblyName">Name of the assembly.</param>         public static AssemblyBuilder Create(string assemblyName)         {             AssemblyName name = new AssemblyName(assemblyName);               AssemblyBuilder assembly = AppDomain.CurrentDomain.DefineDynamicAssembly(                     name, AssemblyBuilderAccess.Run);               DynamicAssemblyCache.Add(assembly);               return assembly;         }           /// <summary>         /// Creates an assembly builder and saves the assembly to the passed in location.         /// </summary>         /// <param name="assemblyName">Name of the assembly.</param>         /// <param name="filePath">The file path.</param>         public static AssemblyBuilder Create(string assemblyName, string filePath)         {             AssemblyName name = new AssemblyName(assemblyName);               AssemblyBuilder assembly = AppDomain.CurrentDomain.DefineDynamicAssembly(                     name, AssemblyBuilderAccess.RunAndSave, filePath);               DynamicAssemblyCache.Add(assembly);               return assembly;         }           #endregion     } }   So hopefully the above class is fairly explanatory, an AssemblyName is created using the passed in string for the actual name of the assembly. An AssemblyBuilder is then constructed with the current AppDomain and depending on the overload used, it is either just run in the current context or it is set up ready for saving. It is then added to the cache.   DynamicAssemblyCache using System.Reflection.Emit; using Rapid.DynamicProxy.Exceptions; using Rapid.DynamicProxy.Resources.Exceptions;   namespace Rapid.DynamicProxy.Assembly {     /// <summary>     /// Cache for storing the dynamic assembly builder.     /// </summary>     internal static class DynamicAssemblyCache     {         #region Declarations           private static object syncRoot = new object();         internal static AssemblyBuilder Cache = null;           #endregion           #region Adds a dynamic assembly to the cache.           /// <summary>         /// Adds a dynamic assembly builder to the cache.         /// </summary>         /// <param name="assemblyBuilder">The assembly builder.</param>         public static void Add(AssemblyBuilder assemblyBuilder)         {             lock (syncRoot)             {                 Cache = assemblyBuilder;             }         }           #endregion           #region Gets the cached assembly                  /// <summary>         /// Gets the cached assembly builder.         /// </summary>         /// <returns></returns>         public static AssemblyBuilder Get         {             get             {                 lock (syncRoot)                 {                     if (Cache != null)                     {                         return Cache;                     }                 }                   throw new RapidDynamicProxyAssertionException(AssertionResources.NoAssemblyInCache);             }         }           #endregion     } } The cache is simply a static property that will store the AssemblyBuilder (I know it’s a little weird that I’ve made it public, this is for testing purposes, I know that’s a bad excuse but hey…) There are two methods for using the cache – Add and Get, these just provide thread safe access to the cache.   The Module Builder The module builder is required as the create proxy classes will need to live inside a module within the assembly. Here’s the code: DynamicModuleBuilder using System.Reflection.Emit; using Rapid.DynamicProxy.Assembly; namespace Rapid.DynamicProxy.Module {     /// <summary>     /// Class for creating a module builder.     /// </summary>     internal static class DynamicModuleBuilder     {         /// <summary>         /// Creates a module builder using the cached assembly.         /// </summary>         public static ModuleBuilder Create()         {             string assemblyName = DynamicAssemblyCache.Get.GetName().Name;               ModuleBuilder moduleBuilder = DynamicAssemblyCache.Get.DefineDynamicModule                 (assemblyName, string.Format("{0}.dll", assemblyName));               DynamicModuleCache.Add(moduleBuilder);               return moduleBuilder;         }     } } As you can see, the module builder is created on the assembly that lives in the DynamicAssemblyCache, the module is given the assembly name and also a string representing the filename if the assembly is to be saved. It is then added to the DynamicModuleCache. DynamicModuleCache using System.Reflection.Emit; using Rapid.DynamicProxy.Exceptions; using Rapid.DynamicProxy.Resources.Exceptions; namespace Rapid.DynamicProxy.Module {     /// <summary>     /// Class for storing the module builder.     /// </summary>     internal static class DynamicModuleCache     {         #region Declarations           private static object syncRoot = new object();         internal static ModuleBuilder Cache = null;           #endregion           #region Add           /// <summary>         /// Adds a dynamic module builder to the cache.         /// </summary>         /// <param name="moduleBuilder">The module builder.</param>         public static void Add(ModuleBuilder moduleBuilder)         {             lock (syncRoot)             {                 Cache = moduleBuilder;             }         }           #endregion           #region Get           /// <summary>         /// Gets the cached module builder.         /// </summary>         /// <returns></returns>         public static ModuleBuilder Get         {             get             {                 lock (syncRoot)                 {                     if (Cache != null)                     {                         return Cache;                     }                 }                   throw new RapidDynamicProxyAssertionException(AssertionResources.NoModuleInCache);             }         }           #endregion     } }   The DynamicModuleCache is very similar to the assembly cache, it is simply a statically stored module with thread safe Add and Get methods.   The DynamicTypeCache To end off this post, I’m going to create the cache for storing the generated proxy classes. I’ve spent a fair amount of time thinking about the type of collection I should use to store the types and have finally decided that for the time being I’m going to use a generic dictionary. This may change when I can actually performance test the proxy generator but the time being I think it makes good sense in theory, mainly as it pretty much maintains it’s performance with varying numbers of items – almost constant (0)1. Plus I won’t ever need to loop through the items which is not the dictionaries strong point. Here’s the code as it currently stands: DynamicTypeCache using System; using System.Collections.Generic; using System.Security.Cryptography; using System.Text; namespace Rapid.DynamicProxy.Types {     /// <summary>     /// Cache for storing proxy types.     /// </summary>     internal static class DynamicTypeCache     {         #region Declarations           static object syncRoot = new object();         public static Dictionary<string, Type> Cache = new Dictionary<string, Type>();           #endregion           /// <summary>         /// Adds a proxy to the type cache.         /// </summary>         /// <param name="type">The type.</param>         /// <param name="proxy">The proxy.</param>         public static void AddProxyForType(Type type, Type proxy)         {             lock (syncRoot)             {                 Cache.Add(GetHashCode(type.AssemblyQualifiedName), proxy);             }         }           /// <summary>         /// Tries the type of the get proxy for.         /// </summary>         /// <param name="type">The type.</param>         /// <returns></returns>         public static Type TryGetProxyForType(Type type)         {             lock (syncRoot)             {                 Type proxyType;                 Cache.TryGetValue(GetHashCode(type.AssemblyQualifiedName), out proxyType);                 return proxyType;             }         }           #region Private Methods           private static string GetHashCode(string fullName)         {             SHA1CryptoServiceProvider provider = new SHA1CryptoServiceProvider();             Byte[] buffer = Encoding.UTF8.GetBytes(fullName);             Byte[] hash = provider.ComputeHash(buffer, 0, buffer.Length);             return Convert.ToBase64String(hash);         }           #endregion     } } As you can see, there are two public methods, one for adding to the cache and one for getting from the cache. Hopefully they should be clear enough, the Get is a TryGet as I do not want the dictionary to throw an exception if a proxy doesn’t exist within the cache. Other than that I’ve decided to create a key using the SHA1CryptoServiceProvider, this may change but my initial though is the SHA1 algorithm is pretty fast to put together using the provider and it is also very unlikely to have any hashing collisions. (there are some maths behind how unlikely this is – here’s the wiki if you’re interested http://en.wikipedia.org/wiki/SHA_hash_functions)   Anyway, that’s the end of part 1 – although I haven’t started any of the fun stuff (by fun I mean hairpulling, teeth grating Relfection.Emit style fun), I’ve got the basis of the DynamicProxy in place so all we have to worry about now is creating the types, interceptor classes, method invocation information classes and finally a really nice fluent interface that will abstract all of the hard-core craziness away and leave us with a lightning fast, easy to use AOP framework. Hope you find the series interesting. All of the source code can be viewed and/or downloaded at our codeplex site - http://rapidioc.codeplex.com/ Kind Regards, Sean.

  Read the article

• WCF <operation>Async methods not generated in proxy interface

  - by Charlie

  I want to use the Asnyc methods rather than the Begin on my WCF service client proxy because I'm updating WPF controls and need to make sure they're being updated from the UI thread. I could use the Dispatcher class to queue items for the UI thread but that's not what I'm asking about.. I've configured the service reference to generate the asynchronous operations, but it only generates the methods in proxy's implementation, not it's interface. The interface only contains syncronous and Begin methods. Why aren't these methods generated in the interface and is there a way to do this, or do I have to create a derived interface to manually add them?

  Read the article

• OpenIndiana (illumos): vmxnet3 interface lost on reboot

  - by protomouse

  I want my VMware vmxnet3 interface to be brought up with DHCP on boot. I can manually configure the NIC with: # ifconfig vmxnet3s0 plumb # ipadm create-addr -T dhcp vmxnet3s0/v4dhcp But after creating /etc/dhcp.vmxnet3s0 and rebooting, the interface is down and the logs show: Aug 13 09:34:15 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:15 neumann vmxnet3s: [ID 715698 kern.notice] vmxnet3s:0: stop() Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:17 neumann vmxnet3s: [ID 920500 kern.notice] vmxnet3s:0: start() Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(TxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxBufPoolLimit) -> 512 Aug 13 09:34:17 neumann nwamd[491]: [ID 605049 daemon.error] 1: nwamd_set_unset_link_properties: dladm_set_linkprop failed: operation not supported Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x20000) -> no Aug 13 09:34:17 neumann nwamd[491]: [ID 751932 daemon.error] 1: nwamd_down_interface: ipadm_delete_addr failed on vmxnet3s0: Object not found Aug 13 09:34:17 neumann nwamd[491]: [ID 819019 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv4 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 160156 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv6 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 771489 daemon.error] 1: add_ip_address: ipadm_create_addr failed on vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 405346 daemon.error] 9: start_dhcp: ipadm_create_addr failed for vmxnet3s0: Operation not supported on disabled object I then tried disabling network/physical:nwam in favour of network/physical:default. This works, the interface is brought up but physical:default fails and my network services (e.g. NFS) refuse to start. # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vmxnet3s0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:1: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:2: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:3: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:4: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:5: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:6: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:7: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:8: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 vmxnet3s0: flags=20002000840<RUNNING,MULTICAST,IPv6> mtu 9000 index 2 inet6 ::/0 # cat /var/svc/log/network-physical\:default.log [ Aug 16 09:46:39 Enabled. ] [ Aug 16 09:46:41 Executing start method ("/lib/svc/method/net-physical"). ] [ Aug 16 09:46:41 Timeout override by svc.startd. Using infinite timeout. ] starting DHCP on primary interface vmxnet3s0 ifconfig: vmxnet3s0: DHCP is already running [ Aug 16 09:46:43 Method "start" exited with status 96. ] NFS server not running: # svcs -xv network/nfs/server svc:/network/nfs/server:default (NFS server) State: offline since August 16, 2012 09:46:40 AM UTC Reason: Service svc:/network/physical:default is not running because a method failed. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:default Reason: Service svc:/network/physical:nwam is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:nwam Reason: Service svc:/network/nfs/nlockmgr:default is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/network/nfs/nlockmgr:default See: man -M /usr/share/man -s 1M nfsd Impact: This service is not running. I'm new to the world of Solaris, so any help solving would be much appreciated. Thanks!

  Read the article

• Sonicwall with failover, multiple subnets, and preferred WAN interface per subnet

  - by Dan

  I am trying to set up my Sonicwall TZ-210 as follows: Two WAN interfaces (different ISPs), set up in failover mode. Two LAN interfaces with different subnets Each LAN subnet will have a preferred outbound WAN interface, but would failover when necessary. In this way, each ISP is being used for a separate subnet of my network, but both subnets could failover to the other ISP if their primary went down. I know how to do 1 and 2, but I don't know how to do 3. I could set up a route for each subnet to go through a specific interface, but what would happen in the event of a failover? Would it automatically update those routes? Thanks!

  Read the article

• pfSense 2.1 OpenVPN client not using tunnelled interface

  - by Brian M. Hunt

  I'm having some trouble getting OpenVPN working on my pfSense box. The issue is quite strange to me. When I have the OpenVPN turned on, only my router is able to connect to the Internet. From the router I can use ping, links, etc., and connections work exactly as expected - through the VPN, with the IP address assigned by my VPN provider (Proxy.sh, incidentally). However, none of the clients on the local network can connect to the Internet. I get timeouts when using ping or a web browser. I can ping my router, and the IP address of the gateway. When I switch the default gateway from the VPN to my ISP's gateway, all works exactly as expected. Here the routing table (netstat -r) when in VPN mode, and a key for it: IPv4 Destination Gateway Flags Refs Use Mtu Netif Expire 0.0.0.0/1 10.XX.X.53 UGS 0 122 1500 ovpnc1 = default 10.XX.X.53 UGS 0 235 1500 ovpnc1 8.8.8.8 10.XX.X.53 UGHS 0 82 1500 ovpnc1 10.XX.X.1/32 10.11.0.53 UGS 0 0 1500 ovpnc1 10.XX.X.53 link#12 UH 0 0 1500 ovpnc1 10.XX.X.54 link#12 UHS 0 0 16384 lo0 ZZ.XX.XXX.0/20 link#1 U 0 83 1500 re0 ZZ.XX.XXX.XXX link#1 UHS 0 0 16384 lo0 127.0.0.1 link#9 UH 0 12 16384 lo0 128.0.0.0/1 10.11.0.53 UGS 0 123 1500 ovpnc1 192.168.1.0/24 link#11 U 0 1434 1500 ue0 192.168.1.1 link#11 UHS 0 0 16384 lo0 YYY.YYY.YYY.YYY/32 ZZ.XX.XXX.1 UGS 0 249 1500 re0 IP addresses 10.XX.X.53/54 - My DHCP-assigned IP address/pair from the VPN provider ZZ.XX.XXX.XXX - My external IP assigned by my ISP YYY.YYY.YYY.YYY - The external IP assigned by the VPN provider Interfaces ovpnc1 - My VPN client interface re0 - My LAN interface ue0 - My WAN interface This looks essentially what I would expect it to be. The default route is through the VPN provider. The VPN address is routed through the ISP-assigned IP address. I am not sure what would be wrong here. So figuring this was a firewall issue, I basically tried enabling all in/out traffic. This did not seem to remedy the problem. Also figuring it could possibly be some client networking issue, I restarted the clients on the LAN. This did not help. I also ran route flush and reset the routes manually. So I am a bit stumped, and would be very grateful for any thoughts on what the problem might be.

  Read the article

• Get CLSID by PIA interface Type

  - by Charles

  How can I get the CLSID for a given interface within a Primary Interop Assembly? Here's what I'm talking about: // The c# compiler does some interesting magic. // The following code ... var app = new Microsoft.Office.Interop.Outlook.Application(); // ... is compiled like so (disassembled with Reflector): var app =((Microsoft.Office.Interop.Outlook.Application) Activator.CreateInstance(Type.GetTypeFromCLSID(new Guid("0006F03A-0000-0000-C000-000000000046")))); Microsoft.Office.Interop.Outlook.Application is an interface, and therefore it cannot be instantiated directly. What's interesting here is that c# lets you treat these COM interfaces as if there where classes that you can instantiate with the new keyword. What I want to know is, given the System.Type for a given interface, how can I get the CLSID? Note: I ultimately want to be able to create an instance given the interface's System.Type - I don't really care how. I'm assuming here that the easiest way to do this would be to get CLSID given the Type, just as the c# compiler does.

  Read the article

• ifconfig return "unknown interface: no such device"

  - by xolstice

  I'm trying to install a Linux driver for my wireless network card (D-Link DWL-G510) on my Red Hat Linux 7.1 machine with a 2.4.37.9 kernel. I downloaded the serial monkey driver from the sourceforge site and was able to successfully compile the rt73 module and load it into the kernel. The problem now is that everytime I issue the command ifconfig wlan0 up it keeps returning with the following error message: wlan0: unknown interface: No such device. I'm at a loss as to what to do here. I specifed wlan0 as the alias for the rt73 module in the modules.conf and also tried to load the driver with the command modprobe rt73 ifname=wlan0 (this specifies the interface name according to the instructions packaged in the driver), but the error message still keeps coming up. Is there something else I need to do in Linux to configure the wlan0 part or is the module not recognizing the wireless network card? It would be quite strange if it is the later since all information from the Internet is indicating this is the linux driver I should be using for mentioned wireless card.

  Read the article

• Disable (or switch off) a network interface on windows but keep the "plug and play"

  - by Leandro

  I'm looking for a good workaround to do this on Windows 7 and Windows XP: Disable or make ineffective the network interface (ETH, WIFI, any NIC). If the user connect his ETH cable, the network interface enable again. Important Notes to take care: I'm working with wmic on Win7 (through the command line) I'm working with devcon on WinXP (through the command line) I'm specifically working with the .NET Framework 2.0 on C# but this is just for informational purposes. I know that an event won't help me to detect it (if there is a way or workaround to do this I don't know it). The real problem is that when I disable the NIC, I can't know if the user connects his cable or has a wired network. This is why I am looking for a workaround. I'll treat suggestions as answers if no direct answer exists. I'll provide any extra detail necessary.

  Read the article

• Static IPv4 and dynamic IPv6 on same interface

  - by Zsub

  I am trying to set up a CentOS 5.4 box to use a static IPv4 address, while getting a dynamic IPv6 address at boot time. I have only one interface, apart from the loopback interface, eth0. It has a static v4 and internet connectivity (I can SSH in). However, it doesn't get an IPv6 by default. I have enabled IPv6 in /etc/sysconfig/network and I have added IPV6INIT=yes to the config in /etc/sysconfig/networking/devices/. If I use dhcp6c it does get a valid IPv6 address, but the main question is how do I configure it to get one at boot-time?

  Read the article

• second ip address on the same interface but on a different subnet

  - by fptstl

  Is it possible in CentOS 5.7 64bit to have a second IP address on one interface (eg. eth0) - alias interface configuration - in a different subnet? Here is the original config for eth0 more etc/sysconfig/network-scripts/ifcfg-eth0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.91.255 HWADDR=00:1D:09:FE:DA:04 IPADDR=192.168.91.250 NETMASK=255.255.255.0 NETWORK=192.168.91.0 ONBOOT=yes And here is the config for eth0:0 more etc/sysconfig/network-scripts/ifcfg-eth0:0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0:0 BOOTPROTO=static BROADCAST=10.10.191.255 DNS1=10.10.15.161 DNS2=10.10.18.36 GATEWAY=10.10.191.254 HWADDR=00:1D:09:FE:DA:04 IPADDR=10.10.191.210 NETMASK=255.255.255.0 NETWORK=10.39.191.0 ONPARENT=yes How would the resolv.conf file should change since there are two different gateways? Any other change needed?

  Read the article

• Single-port 2600 router with 2900XL switch

  - by Slava Maslennikov

  I have a setup, where the single port 2600 router is in port 0/2 in the switch, outside network is on port 0/1, and the rest (0/3-0/24) should be clients for the second network that would be managed by the 2600 router. I configured everything with two VLANs: 100 for outside (0/2-0/24), 200 for inside (0/1-0/2). 0/2 is a trunk port for the two VLANs. The issue that came about is that I can't have two VLANs on at once: software doesn't allow it. Now, I can ping the outside network devices (172.16.7.1, 172.16.7.103), and even google (8.8.8.8) from the router, but not the switch. Devices on connected get a DHCP lease properly but can't ping outside the network, just the router - 172.17.7.1 and the switch itself, 172.17.7.7. The configuration for both the router and the switch are here, as well as below. Router: rt.throom#sho run Building configuration... Current configuration : 1015 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname rt.throom ! enable password To053cret ! ! ! ! ! no ip subnet-zero ip dhcp excluded-address 172.17.7.1 172.17.7.2 ip dhcp excluded-address 172.17.7.3 172.17.7.4 ip dhcp excluded-address 172.17.7.5 ! ip dhcp pool VLAN200 network 172.17.7.0 255.255.255.0 default-router 172.17.7.1 dns-server 8.8.8.8 ! ip audit notify log ip audit po max-events 100 ! ! ! ! ! ! ! interface Ethernet0/0 no ip address ! interface Ethernet0/0.100 encapsulation dot1Q 100 ip address 172.16.7.15 255.255.255.0 ip nat outside ! interface Ethernet0/0.200 encapsulation dot1Q 200 ip address 172.17.7.1 255.255.255.0 ip nat inside ! router eigrp 20 network 172.16.0.0 network 172.17.0.0 no auto-summary no eigrp log-neighbor-changes ! no ip classless no ip http server ! access-list 1 permit 172.17.7.0 0.0.0.255 ! ! line con 0 line aux 0 line vty 0 4 login ! end Switch: sw.throom#sho run Building configuration... Current configuration: ! version 11.2 no service pad no service udp-small-servers no service tcp-small-servers ! hostname sw.throom ! enable password Oh5053cret ! ! no spanning-tree vlan 100 no spanning-tree vlan 200 ip subnet-zero ! ! interface VLAN1 no ip address no ip route-cache ! interface FastEthernet0/1 switchport access vlan 100 spanning-tree portfast ! interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/3 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/5 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/6 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/7 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/8 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/9 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/10 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/11 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/12 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/13 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/14 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/15 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/16 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/17 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/18 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/19 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/20 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/21 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/22 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/23 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/24 switchport access vlan 200 spanning-tree portfast ! ! line con 0 stopbits 1 line vty 0 4 login line vty 5 9 login ! end sho ip route gives: Gateway of last resort is 172.16.7.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.7.0 is directly connected, Ethernet0/0.200 172.16.0.0/24 is subnetted, 1 subnets C 172.16.7.0 is directly connected, Ethernet0/0.100 S* 0.0.0.0/0 [1/0] via 172.16.7.1

  Read the article

• Filesystem access through web interface

  - by Jorge Suárez de Lis

  I have an SSH+Samba server so people can access its files from anywhere on the network. I thought it would be also interesting to provide access through a web interface, so they can access the files even when they don't have access to the VPN or a Samba/SSH client. Something like the Ubuntu One or Dropbox web interface. The http server could be on the same machine as the SSH+Samba, so it should just provide access to local files and some way to login with their username/password. Someone knows any software like this?

  Read the article

• Force local IP traffic to an external interface

  - by calandoa

  I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to be able to forward all the traffic to one of these local address trhough the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 are not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

  Read the article

• Correct way of bringing network interface down in linux

  - by Karolis T.

  For example: $ ifconfig dummy0 up $ ifconfig dummy0 "192.168.1.190 netmask 255.255.255.0" Calling ifconfig with no parameters shows the interface dummy0 Link encap:Ethernet HWaddr b6:1f:f3:92:6d:20 inet addr:192.168.1.190 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::b41f:f3ff:fe92:6d20/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:1050 (1.0 KiB) How can I bring the interface down so that it doesn't show up in ifconfig ifconfig -a ifconfig dummy0 without rmmod dummy because dummy is used just for example purposes. If there is no way to do that, what "throw-away" IP could I set to it and be safe from any trouble? like $ ifconfig dummy0 down $ ifconfig dummy0 0.0.0.0

  Read the article

• How to implement an interface member that returns void in F#

  - by Drew Noakes

  Imagine the following interface in C#: interface IFoo { void Bar(); } How can I implement this in F#? All the examples I've found during 30 minutes of searching online show only examples that have return types which I suppose is more common in a functional style, but something I can't avoid in this instance. Here's what I have so far: type Bar() = interface IFoo with member this.Bar = void Fails with FS0010: Unexpected keyword 'void' in expression.

  Read the article

• Disabling networkmanager for a specific interface

  - by bdonlan

  I'd like to do some experimentation with hostap without disabling my primary wireless interface. How do I tell networkmanager to keep its hands off a specific interface or interfaces while allowing it to continue managing all other interfaces normally? I'm using Ubuntu 9.04. (Wasn't sure if this should go on superuser or serverfault, as networkmanager isn't much of a 'server' tool - if it belongs on serverfault please feel free to move it) Edit: I've tried adding this to /etc/network/interfaces: allow-hotplug wlan2 iface wlan2 inet static address 192.168.49.1 netmask 255.255.255.0 But this has no apparent effect, even after restarting NetworkManager. Here's my /etc/NetworkManager/nm-system-settings.conf: [main] plugins=ifupdown,keyfile [ifupdown] managed=false Edit[2]: Looks like I needed to restart nm-system-settings, then NetworkManager.

  Read the article

• Network-Backup-Software with file versioning and web-interface

  - by dlang

  Dear All! I would like to backup our business-data to a remote backup-server. We would like to set-up our own backup-server running on any operating system (windows appreciated) which comes with a web-interface, that enables to restore individual versions of one file. Because budget is limited, an open-source software or at least a cheap software is a must! Unfortunately I couldn't find even a single software, which fulfills the requirements of file versioning and web-interface for single file-restore. Do any of you have already set-up such a system? Best regards, Daniel Lang

  Read the article

• Routing application traffic through specific interface

  - by UnicornsAndRainbows

  Hello All! First question here, so please go easy: I have a debian linux 5.0 server with two public interfaces. I would like to route outbound traffic from one instance of an application via one interface and the second instance through the second interface. There are some challenges: both instances of the application use the same protocol both instances of the application can access the entire internet (can't route based on dest network) I can't change the code of the application I don't think a typical approach to load balancing all traffic is going to work well, because there are relatively few destination servers being accessed in the outbound traffic, and all traffic would really need to be distributed pretty evenly across these relatively few servers. I could probably run two virtualized servers on the box and bind each of them to a different external ip, but I'm looking for a simpler solution, maybe using iproute or iptables? Any ideas for me? Thanks in advance - and I'm happy to answer any questions.

  Read the article

• Network interface selection

  - by Antonino

  Hello. Suppose I have more than a network interfaces and I want to selectively use them per application. eth0 is the standard interface with the standard gateway in the main routing table eth1 is another interface with a different gateway. Suppose I launch an application as a user "user_eth1". I used the following set of rules for iptables / ip rules. IPTABLES: iptables -t mangle -A OUTPUT -m user --uid-owner user_eth1 -j MARK --set-mark 100 iptables -t nat -A POSTROUTING -m user -uid-owner -o eth1 user_eth1 -j SNAT --to-source <eth_ipaddress> IPRULE: ip rule add fwmark 100 lookup table100 and i build "table100" as follows (no doubts on that) ip route show table main | grep -Ev ^default | while read ROUTE; do ip route add table table100 $ROUTE; done ip route add default via <default_gateway> table table100 It doesn't work at all. What's wrong with this? Thank you in advance!

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >