Search Results

Search found 7823 results on 313 pages for 'leaf dev'.

Page 26/313 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

  • No HDMI Audio with GeForce 9600GT and nForce board

    - by Bobby
    I've been trying to get HDMI with sound working for the last few days, and I'm a little bit out of ideas. (I've verified that the hardware/Setup works via Windows.) aplay does not list my HDMI device: $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: NVidia [HDA NVidia], device 0: ALC662 rev1 Analog [ALC662 rev1 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: NVidia [HDA NVidia], device 1: ALC662 rev1 Digital [ALC662 rev1 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 I've already compiled the alsa drivers (1.0.24) from a snapshot (with --with-oss=no) and added the line options snd-hda-intel model=auto # Tried 3stack-dig and 6stack-dig too to /etc/modprobe.d/alsa-base.conf. Still, the device does not show up. If it is important, the HDMI TV is at the moment not configured to be part of the X session (I've tried that to, at least with X restart, and it didn't change anything). What did I miss? $ lspci 00:00.0 Host bridge: nVidia Corporation Device 07c3 (rev a2) 00:00.1 RAM memory: nVidia Corporation nForce 630i memory controller (rev a2) 00:01.0 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1) 00:01.1 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1) 00:01.2 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1) 00:01.3 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1) 00:01.4 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1) 00:01.5 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1) 00:01.6 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1) 00:02.0 RAM memory: nVidia Corporation nForce 630i memory controller (rev a1) 00:03.0 ISA bridge: nVidia Corporation MCP73 LPC Bridge (rev a2) 00:03.1 SMBus: nVidia Corporation MCP73 SMBus (rev a1) 00:03.2 RAM memory: nVidia Corporation MCP73 Memory Controller (rev a1) 00:03.4 RAM memory: nVidia Corporation MCP73 Memory Controller (rev a1) 00:04.0 USB Controller: nVidia Corporation GeForce 7100/nForce 630i USB (rev a1) 00:04.1 USB Controller: nVidia Corporation MCP73 [nForce 630i] USB 2.0 Controller (EHCI) (rev a1) 00:08.0 IDE interface: nVidia Corporation MCP73 IDE (rev a1) 00:09.0 Audio device: nVidia Corporation MCP73 High Definition Audio (rev a1) 00:0a.0 PCI bridge: nVidia Corporation MCP73 PCI Express bridge (rev a1) 00:0b.0 PCI bridge: nVidia Corporation MCP73 PCI Express bridge (rev a1) 00:0c.0 PCI bridge: nVidia Corporation MCP73 PCI Express bridge (rev a1) 00:0d.0 PCI bridge: nVidia Corporation MCP73 PCI Express bridge (rev a1) 00:0e.0 IDE interface: nVidia Corporation MCP73 IDE (rev a2) 00:0f.0 Ethernet controller: nVidia Corporation MCP73 Ethernet (rev a2) 02:00.0 VGA compatible controller: nVidia Corporation G94 [GeForce 9600 GT] (rev a1)   $ aplay -L default pulse Playback/recording through the PulseAudio sound server front:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Analog Front speakers surround40:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Digital IEC958 (S/PDIF) Digital Audio Output dmix:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Analog Direct sample mixing device dmix:CARD=NVidia,DEV=1 HDA NVidia, ALC662 rev1 Digital Direct sample mixing device dsnoop:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Analog Direct sample snooping device dsnoop:CARD=NVidia,DEV=1 HDA NVidia, ALC662 rev1 Digital Direct sample snooping device hw:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Analog Direct hardware device without any conversions hw:CARD=NVidia,DEV=1 HDA NVidia, ALC662 rev1 Digital Direct hardware device without any conversions plughw:CARD=NVidia,DEV=0 HDA NVidia, ALC662 rev1 Analog Hardware device with all software conversions plughw:CARD=NVidia,DEV=1 HDA NVidia, ALC662 rev1 Digital Hardware device with all software conversions

    Read the article

  • How to check if a cdrom is in the tray remotely (via ssh)?

    - by adempewolff
    I have a server running Ubuntu 10.04 (it's on the other side of the world and I haven't built up the wherewithal to upgrade it remotely yet) and I have been told that there is a CD in one of it's two CD drives. I want to rip an image of the cd and then download it to my local computer (I don't need help with either of these steps). However, I cannot seem to confirm whether or not there actually is a CD in the drive as I was told. It did not automatically mount anywhere (which I'm thinking might just be a result of it being a headless server not running X, nautilus, or any of the other nice user friendly things). There are two CD drives connected via SCSI: austin@austinvpn:/proc/scsi$ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: ATA Model: WDC WD400EB-75CP Rev: 06.0 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: Lite-On Model: LTN486S 48x Max Rev: YDS6 Type: CD-ROM ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: SAMSUNG Model: CD-R/RW SW-248F Rev: R602 Type: CD-ROM ANSI SCSI revision: 05 However when I try mounting either of these devices (and every other device that could possibly be the cd-drive), it says no medium found: austin@austinvpn:/proc/scsi$ sudo mount -t iso9660 /dev/scd1 /cdrom mount: no medium found on /dev/sr1 austin@austinvpn:/proc/scsi$ sudo mount -t iso9660 /dev/scd0 /cdrom mount: no medium found on /dev/sr0 austin@austinvpn:/proc/scsi$ sudo mount -t iso9660 /dev/cdrom /cdrom mount: no medium found on /dev/sr1 austin@austinvpn:/proc/scsi$ sudo mount -t iso9660 /dev/cdrom1 /cdrom mount: no medium found on /dev/sr0 austin@austinvpn:/proc/scsi$ sudo mount -t iso9660 /dev/cdrw /cdrom mount: no medium found on /dev/sr1 Here are the contents of my /dev folder: austin@austinvpn:/proc/scsi$ ls /dev agpgart loop6 ram6 tty10 tty38 tty8 austinvpn loop7 ram7 tty11 tty39 tty9 block lp0 ram8 tty12 tty4 ttyS0 bsg mapper ram9 tty13 tty40 ttyS1 btrfs-control mcelog random tty14 tty41 ttyS2 bus mem rfkill tty15 tty42 ttyS3 cdrom net root tty16 tty43 urandom cdrom1 network_latency rtc tty17 tty44 usbmon0 cdrw network_throughput rtc0 tty18 tty45 usbmon1 char null scd0 tty19 tty46 usbmon2 console oldmem scd1 tty2 tty47 usbmon3 core parport0 sda tty20 tty48 usbmon4 cpu_dma_latency pktcdvd sda1 tty21 tty49 vcs disk port sda2 tty22 tty5 vcs1 dri ppp sda5 tty23 tty50 vcs2 ecryptfs psaux sg0 tty24 tty51 vcs3 fb0 ptmx sg1 tty25 tty52 vcs4 fd pts sg2 tty26 tty53 vcs5 full ram0 shm tty27 tty54 vcs6 fuse ram1 snapshot tty28 tty55 vcs7 hpet ram10 snd tty29 tty56 vcsa input ram11 sndstat tty3 tty57 vcsa1 kmsg ram12 sr0 tty30 tty58 vcsa2 log ram13 sr1 tty31 tty59 vcsa3 loop0 ram14 stderr tty32 tty6 vcsa4 loop1 ram15 stdin tty33 tty60 vcsa5 loop2 ram2 stdout tty34 tty61 vcsa6 loop3 ram3 tty tty35 tty62 vcsa7 loop4 ram4 tty0 tty36 tty63 vga_arbiter loop5 ram5 tty1 tty37 tty7 zero And here is my fstab file: austin@austinvpn:/proc/scsi$ cat /etc/fstab # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 /dev/mapper/austinvpn-root / ext4 errors=remount-ro 0 1 # /boot was on /dev/sda1 during installation UUID=ed5520ae-c690-4ce6-881e-3598f299be06 /boot ext2 defaults 0 2 /dev/mapper/austinvpn-swap_1 none swap sw 0 0 Am I missing something/doing something wrong, or is there just no CD in the drive or is the drive possibly broken? Is there any nice command to list devices with mountable media? Thanks in advance for any help!

    Read the article

  • Ubuntu Server 12 not spawning a serial ttyS0 when running on Xen

    - by segfaultreloaded
    I have this problem on more than one host, so the specific hardware is not an issue. Bare metal Ubuntu 12 is not creating a login process on the only serial port, in the default configuration. The serial port works correctly with the firmware. It works correctly with Grub2. I have even connected the serial line to 2 different external client boxes, so the problem is neither the hardware nor the remote client. When finally booted, the system fails to create the login process. root@xenpro3:~# ps ax | grep tty 1229 tty4 Ss+ 0:00 /sbin/getty -8 38400 tty4 1233 tty5 Ss+ 0:00 /sbin/getty -8 38400 tty5 1239 tty2 Ss+ 0:00 /sbin/getty -8 38400 tty2 1241 tty3 Ss+ 0:00 /sbin/getty -8 38400 tty3 1245 tty6 Ss+ 0:00 /sbin/getty -8 38400 tty6 1403 tty1 Ss+ 0:00 /sbin/getty -8 38400 tty1 1996 pts/0 S+ 0:00 grep --color=auto tty root@xenpro3:~# dmesg | grep tty [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-3.2.0-30-generic root=/dev/mapper/xenpro3-root ro console=ttyS0,115200n8 [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.2.0-30-generic root=/dev/mapper/xenpro3-root ro console=ttyS0,115200n8 [ 0.000000] console [ttyS0] enabled [ 2.160986] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.203396] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.263296] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.323102] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A root@xenpro3:~# uname -a Linux xenpro3 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux root@xenpro3:~# I have tried putting a ttyS0.conf file in /etc/initab, which solves the problem bare metal but I still cannot get the serial port to work when booting Ubuntu on top of Xen, as domain 0. My serial line output looks like this, when booting Xen /dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A * Exporting directories for NFS kernel daemon... [ OK ] * Starting NFS kernel daemon [ OK ] SSL tunnels disabled, see /etc/default/stunnel4 [ 18.654627] XENBUS: Unable to read cpu state [ 18.659631] XENBUS: Unable to read cpu state [ 18.664398] XENBUS: Unable to read cpu state [ 18.669248] XENBUS: Unable to read cpu state * Starting Xen daemons [ OK ] mountall: Disconnected from Plymouth At this point, the serial line is no longer connected to a process. Xen itself is running just fine. Dmesg gives me a long list of [ 120.236841] init: ttyS0 main process ended, respawning [ 120.239717] ttyS0: LSR safety check engaged! [ 130.240265] init: ttyS0 main process (1631) terminated with status 1 [ 130.240294] init: ttyS0 main process ended, respawning [ 130.242970] ttyS0: LSR safety check engaged! which is no surprise because I see root@xenpro3:~# ls -l /dev/ttyS? crw-rw---- 1 root tty 4, 64 Nov 7 14:04 /dev/ttyS0 crw-rw---- 1 root dialout 4, 65 Nov 7 14:04 /dev/ttyS1 crw-rw---- 1 root dialout 4, 66 Nov 7 14:04 /dev/ttyS2 crw-rw---- 1 root dialout 4, 67 Nov 7 14:04 /dev/ttyS3 crw-rw---- 1 root dialout 4, 68 Nov 7 14:04 /dev/ttyS4 crw-rw---- 1 root dialout 4, 69 Nov 7 14:04 /dev/ttyS5 crw-rw---- 1 root dialout 4, 70 Nov 7 14:04 /dev/ttyS6 crw-rw---- 1 root dialout 4, 71 Nov 7 14:04 /dev/ttyS7 crw-rw---- 1 root dialout 4, 72 Nov 7 14:04 /dev/ttyS8 crw-rw---- 1 root dialout 4, 73 Nov 7 14:04 /dev/ttyS9 If I manually change the group of /dev/ttyS0 to dialout, it gets changed back. I have made no changes to the default udev rules, so I cannot see where this problem is coming from. Sincerely, John

    Read the article

  • Fresh Ubuntu Install - Grub not loading

    - by Ryan Sharp
    System Ubuntu 12.04 64-bit Windows 7 SP1 Samsung 64GB SSD - OS' Samsung 1TB HDD - Games, /Home, Swap WD 300'ishGB HDD - Backup Okay, so I'm very frustrated, so please excuse me if I miss anything out as my head is clouded by anger and impatience, etc. I'll try me best, though. First of all, I'll explain how I got to my predicament. I finally got my new SSD. I firstly installed Windows, which completed without a hitch. Afterwards, I tried to install Ubuntu, which failed several times due to problems irrelevant to this question, but I mention this to explain my frustrations, sorry. Anyway, I finally installed Ubuntu. However, I chose the 'bootloader' to be installed on the same partition as where I was installing the Ubuntu Root partition, as that was what I believed to be the best choice. It was of my thinking that it was supposed to go on the same partition and on the SSD, which is my OS drive, though with my problem, it apparently was wrong. So I tried to fix it by checking guides and following their directions, but seemed to have messed it up even more. Here is what I receive after I use the fdisk -l command: (I also added explanations for which I used each partition for) Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x324971d1 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 208896 48957439 24374272 7 HPFS/NTFS/exFAT /dev/sda3 48959486 125044735 38042625 5 Extended /dev/sda5 48959488 125044735 38042624 83 Linux sda1 --/ Windows Recovery sda2 --/ Windows 7 sda3/5 --/ Ubuntu root [ / ] Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc0ee6a69 Device Boot Start End Blocks Id System /dev/sdb1 1024208894 1953523711 464657409 5 Extended /dev/sdb3 * 2048 1024206847 512102400 7 HPFS/NTFS/exFAT /dev/sdb5 1024208896 1939851263 457821184 83 Linux /dev/sdb6 1939853312 1953523711 6835200 82 Linux swap / Solaris sdb3 --/ Partition for Steam games, etc. sdb5 --/ Ubuntu Home [ /home ] sdb6 --/ Ubuntu Swap Partition table entries are not in disk order Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x292eee23 Device Boot Start End Blocks Id System /dev/sdc1 2048 625141759 312569856 7 HPFS/NTFS/exFAT sdc1 --/ Generic backup I also used a Boot Script that other users suggested, so that I can give more details on my partitions and also where Grub is located... ============================= Boot Info Summary: =============================== => Grub2 (v1.99) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Grub2 (v1.99) is installed in the MBR of /dev/sdb and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Windows is installed in the MBR of /dev/sdc. Now that is weird... Why would Grub2 be installed on both my SSD and HDD? Even weirder is why is Windows on the MBR of my backup hard drive? Nothing I did should have done that... Anyway, here is the entire Output from that script... PASTEBIN So, to summarize what I need: How can I fix my setup so grub loads on startup? How can I clean my partitions to remove unnecessary grubs? What did I do wrong so that I don't do something so daft again? Thank you so much for reading, and I hope you can help me. I've been trying to have a successful setup since Friday, and I'm almost at the point that I'm really tempted to throw my computer out the window due to my frustration.

    Read the article

  • How to fix: Ubuntu 12.04 reboots after loading with elilo

    - by Casey
    I have an HP p6-2120 with CPU: AMD A6-3620 APU with Radeon Graphics RAM: 6GB BIOS: HO2_710.ROM v7.10 [AMI v7.10 4/19/2012] Disk: SATA1 (/dev/sda) - 1 TB (windows) Disk: SATA2 (/dev/sdb) - 1 TB partitioned using "parted -a optimal /dev/sdb" as follows: .. 1049KB 201MB FAT32 boot flag set .. 201MB 60GB ext2 (/) .. 68GB 78GB linux-swap(v1) (swap) .. 78GB 790GB ext4 (/home) .. - rest is "free" space reserved for other purposes (eventually) ubuntu: 12.04.1 LTS [specifically: Release 12.04 (precise) 64-bit] kernel: linux 3.2.0-29-generic I created a bootable EFI USB from the ISO (64-bit) which I downloaded. I can run and install from the USB without any problems. The BIOS is an EFI bios that appears to be capable of booting in either EFI or Legacy mode. Initially, I did the "standard" install with NOTHING on disk2, and let the installer configure everything. The net result of this was that when I started the computer and forced it into "boot" menu mode, it DOES NOT recognize SATA2 as an EFI drive, and when I attempt to "legacy" boot from it, I get the message "ERROR: No Boot Disk has been detected." The "standard" install created one large partition that consumed the entire disk. At that point, I manually partitioned the disk (using sudo parted -a optimal /dev/sdb) as described above. I selected the "other" install, and changed the /dev/sdb1 to "bios_grub", /dev/sdb2 as "/" (ext4), /dev/sdb3 as swap, and /dev/sdb4 as "/home". [Note: fearing that possibly elilo did not recognize ext4, I switched /dev/sdb2 to ext2 and re-insalled] The net result was that the install appeared to trash the /dev/sdb1 partition so that it was NOT readable by anything. I re-formated /dev/sdb1 as FAT32 and set the boot flag. I repeated the install ignoring the messages about no bios_grub partition. After several attempts to get GRUB2 to work, I switched to elilo. I downloaded the most recent version and copied it (elilo-3.14-ia64.efi) to /dev/sdb1/efi/boot/bootx64.efi. (The BIOS boot loader did not recognize it either as elilo-3.14.ia64.efi or as elilo.efi. Based on the advice in one of the web-pages I found, I renamed it to bootx64.efi. This worked.) In that same directory (/efi/boot), I copied the file pointed to the link in /dev/sdb2/vmlinuz to /efi/boot/vmlinuz, and the file pointed to the link in /dev/sdb2/initrd.img to /efi/boot/initrd.img. I created an elilo.conf file as follows: timeout=5000 prompt default=linux-boot image=vmlinuz label=linux-boot read-only initrd=initrd.img root=/dev/sdb2 The /efi/boot directory contains 4 files: bootx64.efi elilo.conf vmlinuz initrd.img When I power-cycle the computer and force the boot menu, drive2 shows up as an EFI bootable drive. When I select it, I get the elilo prompt. Pressing , it appears to load the kernal (I have tried it with verbose=5, and there is a long string of messages with the final one a command line to load the kernel and a series of several dots that fly by) then the screen goes blank, and it reboots the computer. [Note: I have also tried substituting the UUID as found in the /etc/fstab of the installed system for the root directory. This had no effect.] This is a brief synopsis of several nights of fiddling with this. I would deeply appreciate any help you can give.

    Read the article

  • Getting Audio from a Zone

    - by bleonard
    Now that I have Firefox and Java Web Start running from a zone, the last piece of the puzzle was audio (essential because most Flash content is accompanied by sound).  In the global zone there's a nice little utility called audiotest for testing your sound: bleonard@solaris:~$ audiotest Sound subsystem and version: SunOS Audio 4.0 (0x00040003) Platform: SunOS 5.11 snv_151a i86pc *** Scanning sound adapter #1 *** /dev/sound/audio810:0dsp (audio engine 0): audio810#0 - Performing audio playback test... <left> ................OK <right> ...............OK <stereo> ..............OK <measured sample rate 47727.00 Hz (-0.57%)> *** All tests completed OK *** Of course, before you can try audiotest in a zone, it must be installed: root@myzone:~# pkg install audio-utilities Packages to install: 1 Create boot environment: No DOWNLOAD PKGS FILES XFER (MB) Completed 1/1 6/6 0.4/0.4 PHASE ACTIONS Install Phase 20/20 PHASE ITEMS Package State Update Phase 1/1 Image State Update Phase 2/2 However, we'll need to do more than just install audiotest: root@myzone:~# audiotest /dev/mixer: No such file or directory The device file is missing from /dev. The audio devices also need to be added to the zone. For this we modify the zone configuration as follows: bleonard@solaris:~$ sudo zonecfg -z myzone Password: zonecfg:myzone> add device zonecfg:myzone:device> set match=/dev/audio* zonecfg:myzone:device> end zonecfg:myzone> add device zonecfg:myzone:device> set match=/dev/sound/* zonecfg:myzone:device> end zonecfg:myzone> add device zonecfg:myzone:device> set match=/dev/mixer* zonecfg:myzone:device> end zonecfg:myzone> add device zonecfg:myzone:device> set match=/dev/sndstat zonecfg:myzone:device> end zonecfg:myzone> verify zonecfg:myzone> exit Then reboot the zone: bleonard@solaris:~$ sudo zoneadm -z myzone reboot After which, audiotest should work: root@myzone:~# audiotest Sound subsystem and version: SunOS Audio 4.0 (0x00040003) Platform: SunOS 5.11 snv_151a i86pc *** Scanning sound adapter #1 *** /dev/sound/audio810:0dsp (audio engine 0): audio810#0 - Performing audio playback test... <left> ................OK <right> ...............OK <stereo> ..............OK <measured sample rate 48208.00 Hz (0.43%)> *** All tests completed OK *** You can also examine /dev/sndstat for additional information: root@myzone:~# cat /dev/sndstat SunOS Audio Framework Audio Devices: 0: audio810#0 Intel AC'97, ICH (DUPLEX) Mixers: 0: audio810#0 Intel AC'97, ICH AC'97 codec: SigmaTel STAC9700 However, when testing the sound from Firefox (from a user account other than root), such as this recent Flash presentation on Solaris availability, you may still be disappointed. This is simply a permissions problem, as the devices only have read and write permissions for root: root@myzone:~# ls -l /dev/audio* crw------- 1 root root 99, 3 Jul 1 10:21 /dev/audio crw------- 1 root root 99, 4 Jul 1 10:21 /dev/audioctl To address this: root@myzone:~# chmod 777 /dev/audio* root@myzone:~# chmod 777 /dev/sound/* And you should be all set.

    Read the article

  • How to use Hardware RAID in Ubuntu Server

    - by user2071938
    I have an Adaptec RAID-Controller and created an RAID-1(Mirroring) succesfully. Now I have installed Ubuntu Server 12.04.3. When I type fdisk -l I get this output: bf@fileserver:~$ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/sda doesn't contain a valid partition table Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/sdb doesn't contain a valid partition table Disk /dev/sdc: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004c454 Device Boot Start End Blocks Id System /dev/sdc1 * 2048 499711 248832 83 Linux /dev/sdc2 501758 156301311 77899777 5 Extended /dev/sdc5 501760 156301311 77899776 8e Linux LVM Disk /dev/mapper/fileserver--vg-root: 75.6 GB, 75606523904 bytes 255 heads, 63 sectors/track, 9191 cylinders, total 147668992 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/fileserver--vg-root doesn't contain a valid partition table Disk /dev/mapper/ddf1_Data: 1000.1 GB, 1000065728512 bytes 255 heads, 63 sectors/track, 121584 cylinders, total 1953253376 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/mapper/ddf1_Data doesn't contain a valid partition table Disk /dev/mapper/fileserver--vg-swap_1: 4160 MB, 4160749568 bytes 255 heads, 63 sectors/track, 505 cylinders, total 8126464 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/fileserver--vg-swap_1 doesn't contain a valid partition table The 80 GB HDD is for the System The 1000.2 GB HDD should be for my data. But I'm a bit confused becauser there are listed two 1000.2 GB HDDs, due the Hardware RAID shoudln't there be only one HDD vissible to the OS? (I have two 1000.2 GB HDDs in an Raid-1 Array) dmraid gives me bf@fileserver:~$ sudo dmraid -r /dev/sdb: ddf1, ".ddf1_disks", GROUP, ok, 1953253376 sectors, data@ 0 /dev/sda: ddf1, ".ddf1_disks", GROUP, ok, 1953253376 sectors, data@ 0 so It seems to be ok? But how do I partitionate this disks and which one should I mount(sdb or sda?) Hope you can help me thx Florian

    Read the article

  • Kubuntu: apt-get install of php5-dev: libtool version mismatch?

    - by pinkgothic
    (Warning, clueless-newbism ahead.) Background info: I'm actually trying to install/upgrade xdebug. sudo pecl install xdebug yields: downloading xdebug-2.0.5.tgz ... Starting to download xdebug-2.0.5.tgz (289,234 bytes) ............................................................done: 289,234 bytes 67 source files, building running: phpize sh: phpize: not found ERROR: `phpize' failed A quick google tells me that phpize is a part of a package called php5-dev, so off I ran to install that. My problem is that using sudo apt-get install php5-dev fails with this output: sudo apt-get install php5-dev Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: php5-dev: Conflicts: libtool (>= 2.2) but 2.2.6a-4 is to be installed E: Broken packages 2.2.6a-4 is greater than 2.2, so I'm not sure why it's hanging itself up at that point. I'm guessing the fact that it's not entirely numeric is throwing apt-get off? I can probably install xdebug manually (though I've never done this before, so picture me with a deer clueless-newb in headlights look here, violently shaking my head and begging for a simpler solution) rather than via pecl / aptitude, but is there a way I can make aptitude install php5-dev despite the bogus 'broken package' claim? Is it even bogus, or am I misreading the error message? Alternatively: Could I install phpize in some other way (e.g. via pear or pecl)?

    Read the article

  • Kubuntu: apt-get install of php5-dev: libtool version mismatch?

    - by pinkgothic
    (Warning, clueless-newbism ahead.) Background info: I'm actually trying to install/upgrade xdebug. sudo pecl install xdebug yields: downloading xdebug-2.0.5.tgz ... Starting to download xdebug-2.0.5.tgz (289,234 bytes) ............................................................done: 289,234 bytes 67 source files, building running: phpize sh: phpize: not found ERROR: `phpize' failed A quick google tells me that phpize is a part of a package called php5-dev, so off I ran to install that. My problem is that using sudo apt-get install php5-dev fails with this output: sudo apt-get install php5-dev Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: php5-dev: Conflicts: libtool (>= 2.2) but 2.2.6a-4 is to be installed E: Broken packages 2.2.6a-4 is greater than 2.2, so I'm not sure why it's hanging itself up at that point. I'm guessing the fact that it's not entirely numeric is throwing apt-get off? I can probably install xdebug manually (though I've never done this before, so picture me with a deer clueless-newb in headlights look here, violently shaking my head and begging for a simpler solution) rather than via pecl / aptitude, but is there a way I can make aptitude install php5-dev despite the bogus 'broken package' claim? Is it even bogus, or am I misreading the error message? Alternatively: Could I install phpize in some other way (e.g. via pear or pecl)?

    Read the article

  • Linux not picking up new partition correctly on emc pseudo device

    - by James
    Hi We have a database server running oracle rac. We were recently running out of space on the main LUN that it is attached to. I created a new 100GB LUN and concatenated this onto the existing LUN creating a new MetaLUN. After some messing I managed to get linux to recognise the new space. I then created a new partition in on the pseudo device, to use the new space. Previously when I have done this on other system the next step is to create an ASM disk on the new partition and add this disk to the oracle disk group. This however fails. I am aware of various issues with ASM and powerpath, but I don't think this is the issue here. As on while investigating the issue I discovered that one of the underlying logical device is not reflecting the size change. See below; Powermt displays all of the underlying logical units [root@XXXXX~]# powermt display dev=emcpowerd Pseudo name=emcpowerd CLARiiON ID=CKM00091500009 [VFRAC2] Logical device ID=6006016030312200787502866C65DE11 [LUN 30] state=alive; policy=CLAROpt; priority=0; queued-IOs=0 Owner: default=SP A, current=SP A Array failover mode: 1 ============================================================================== ---------------- Host --------------- - Stor - -- I/O Path - -- Stats --- ### HW Path I/O Paths Interf. Mode State Q-IOs Errors ============================================================================== 3 qla2xxx sde SP A0 active alive 0 0 3 qla2xxx sdj SP B0 active alive 0 0 4 qla2xxx sdo SP A1 active alive 0 0 4 qla2xxx sdt SP B1 active alive 0 0 Fdisk on the pseudo device shows correct space. [root@XXXXX ~]# fdisk -l /dev/emcpowerd Disk /dev/emcpowerd: 429.4 GB, 429496729600 bytes 255 heads, 63 sectors/track, 52216 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/emcpowerd1 1 39162 314568733+ 83 Linux /dev/emcpowerd2 39163 52216 104856255 83 Linux fdisk on one of the logical units is wrong [root@XXXXX~]# fdisk -l /dev/sde Disk /dev/sde: 322.1 GB, 322122547200 bytes 255 heads, 63 sectors/track, 39162 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sde1 1 39162 314568733+ 83 Linux /dev/sde2 39163 52216 104856255 83 Linux fdisk on the rest of the units is fine [root@XXXXX ~]# fdisk -l /dev/sdj Disk /dev/sdj: 429.4 GB, 429496729600 bytes 255 heads, 63 sectors/track, 52216 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdj1 1 39162 314568733+ 83 Linux /dev/sdj2 39163 52216 104856255 83 Linux Also when I created the the partition linux did not create the any entries in the /dev directory for the second partition so I created these manually [root@XXXXX dev]# mknod sde2 b 8 66 [root@XXXXX dev]# ls -al sd[ejot]? brw-r----- 1 root disk 8, 65 Dec 29 14:20 sde1 brw-r--r-- 1 root disk 8, 66 Apr 8 20:31 sde2 brw-r----- 1 root disk 8, 145 Dec 29 14:19 sdj1 brw-r--r-- 1 root disk 8, 146 Apr 8 20:33 sdj2 brw-r----- 1 root disk 8, 225 Apr 6 23:12 sdo1 brw-r--r-- 1 root disk 8, 226 Apr 8 20:33 sdo2 brw-r----- 1 root disk 65, 49 Dec 29 14:19 sdt1 brw-r--r-- 1 root disk 65, 50 Apr 8 20:33 sdt2 This is a production server that we cannot easily reboot. Any ideas would be much appreciated. J

    Read the article

  • nc or socat: How to read data from remote:/dev/ttyACM0 ?

    - by AndreasT
    I have a device running at a remote computer on /dev/ttyACM0 Now I want to read that data on my computer. I can connect to it over ssh. Unfortunately I am a nc/socat rookie and no howto covered this. Semantically like this: cat remote:/dev/ttyACM0 The remote system has a limited linux on it, and I can't install packages. (socat is not available there, nc is) Super cool would be to have some forwarded device: local:/dev/ttySOCK0 pointing to remote:/dev/ttyACM0 Thanks for any help.

    Read the article

  • xen-create-image does not create inird or initramfs image and domU does not starts with system image

    - by user219372
    I have Fedora 19 as Dom0. To create image I run # xen-create-image --hostname=debian-wheezy --memory=512Mb --dhcp --size=20Gb --swap=512Mb --dir=/xen --arch=amd64 --dist=wheezy After generation finished I start vm and see: # xl create /etc/xen/debian-wheezy.cfg Parsing config from /etc/xen/debian-wheezy.cfg libxl: error: libxl_dom.c:409:libxl__build_pv: xc_dom_ramdisk_file failed: No such file or directory libxl: error: libxl_create.c:919:domcreate_rebuild_done: cannot (re-)build domain: -3 In the /etc/xen/debian-wheezy.cfg i have # # Kernel + memory size # kernel = '/boot/vmlinuz-3.11.2-201.fc19.x86_64' ramdisk = '/boot/initrd.img-3.11.2-201.fc19.x86_64' and ls -1 /boot/*201* shows /boot/config-3.11.2-201.fc19.x86_64 /boot/initramfs-3.11.2-201.fc19.x86_64.img /boot/System.map-3.11.2-201.fc19.x86_64 /boot/vmlinuz-3.11.2-201.fc19.x86_64 Then if I fix ramdisk directive in .cfg file to /boot/initramfs-3.11.2-201.fc19.x86_64.img vm will start but os inside will not boot. In a tail of xl console I get [ OK ] Reached target Basic System. dracut-initqueue[130]: Warning: Could not boot. dracut-initqueue[130]: Warning: /dev/disk/by-uuid/085883ad-73ca-45cc-8bc5-e6249f869b26 does not exist dracut-initqueue[130]: Warning: /dev/fedora/root does not exist dracut-initqueue[130]: Warning: /dev/fedora/swap does not exist dracut-initqueue[130]: Warning: /dev/mapper/fedora-root does not exist dracut-initqueue[130]: Warning: /dev/mapper/fedora-swap does not exist dracut-initqueue[130]: Warning: /dev/xvda2 does not exist Starting Dracut Emergency Shell... Warning: /dev/disk/by-uuid/085883ad-73ca-45cc-8bc5-e6249f869b26 does not exist Warning: /dev/fedora/root does not exist Warning: /dev/fedora/swap does not exist Warning: /dev/mapper/fedora-root does not exist Warning: /dev/mapper/fedora-swap does not exist Warning: /dev/xvda2 does not exist Generating "/run/initramfs/sosreport.txt" Entering emergency mode. Exit the shell to continue. Type "journalctl" to view system logs. You might want to save "/run/initramfs/sosreport.txt" to a USB stick or /boot after mounting them and attach it to a bug report. dracut:/# .img files in /xen/domains/debian-wheezy exists and listed in disk section of debian-wheezy.cfg So what should i do? Update: I've found that xl does not mount images. In debian-wheezy.cfg I have that: root = '/dev/xvda2 ro' disk = [ 'file:/xen/domains/debian-wheezy/disk.img,xvda2,w', 'file:/xen/domains/debian-wheeze/swap.img,xvda1,w', ] And there is no /dev/xvda* or /dev/sda* or /dev/hda* files in VM.

    Read the article

  • How do I tell which kernel module is servicing a /dev device?

    - by regulatre
    How do I find out which kernel module (as seen by typing lsmod) is servicing a particular device in /dev ? In other words, say I have a device, /dev/mouse0 and I want to find out which kernel module is installed to service that device. How do I do that? Another way to look at this is, some loaded kernel modules associate themselves with a device in /dev. How does one find out which device(s) a module is "attached" to?

    Read the article

  • SDcard /dev/sdb2 is apparently in use by the system; will not make a filesystem here

    - by user171223
    I divided my sdcard into 2 partitions, but It got an error and couldn't create a new partition. Error: /dev/sdb2 is apparently in use by the system; will not make a filesystem here! My /dev/sdb was not mounted, and the output of command lsblk was: cxphong@cxphong:~/Desktop$ lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sr0 11:0 1 1024M 0 rom sda 8:0 0 465.8G 0 disk +-sda1 8:1 0 118.8G 0 part +-sda2 8:2 0 147.7G 0 part /media/DATA +-sda3 8:3 0 137.1G 0 part +-sda4 8:4 0 1K 0 part +-sda5 8:5 0 1023M 0 part [SWAP] +-sda6 8:6 0 61.2G 0 part / sdb 8:16 1 3.7G 0 disk +-sdb1 8:17 1 70.6M 0 part +-sdb2 8:18 1 3.6G 0 part +-sdb1 (dm-0) 252:0 0 70.6M 0 part +-sdb2 (dm-1) 252:1 0 3.6G 0 part I couldn't delete /dev/sdb1 (dm-0) & /dev/sdb2 (dm-1). What are they?

    Read the article

  • System.Json namespace missing from Windows Phone 7

    - by Freyday
    During a Mix10 presentation, the presenter (Charlie Kindel) said that when writing Silverlight based apps for WP7 you get all of Silverlight 3.0 with some of Silverlight 4.0 mixed in. Why then is System.Json missing? It was included in Silverlight 3.0, and is included in Silverlight 4.0. Windows Phone 7 Class Library Reference

    Read the article

  • How to add custom fields in WordPress "Add a New Post" page?

    - by KPL
    Hello awesome people, I want to add a custom field on Add A New Post page. Like - if I am to make a plugin which will post links to Twitter after a new post is made, I would like to give ability to user to select if he wants to tweet that particular post's link to Twitter. I want to display a check box somewhere in the page which says - "Post this on Twitter" and then check for it and make a tweet. I have seen some plugins which do this. But can't remember which they were. Can someone please help me out?

    Read the article

  • Accessing original WordPress blog's DB from sub-blogs in network mode

    - by aendrew
    I'm helping with a university radio station website that runs WordPress and was recently switched over to Network (Multi-site/multi-user) mode by myself. The setup is as such: The parent site (www.stationID.com) runs a bunch of custom-built plugins to construct things like the show schedule calendar, the "Now Playing" widget, podcast list, et cetera. The new network websites ("wiki.stationID.com", "buddypress.stationID.com" for instance) run the same template as the parent site, but it stops after rendering the first section because the widgets from point 1 grab data from the main site's database that is not available to sub-blogs. My question is: how do I get data from the main site's tables on the sub-domain sub-blogs? A related question is: how do I set the $wpdb->prefix to be the same as the parent site on the child websites without it negatively effecting how the child website pulls data from its own database? Any help would be awesome, thanks!

    Read the article

  • EXC_BAD_ACCESS NSUrlConnection

    - by Lars
    Hi all, i got an EXC_BAD_ACCESS when i perform the last line of the function (webData). -(void)requestSoap{ NSString *requestUrl = @"http://www.website.com/webservice.php"; NSString *soapMessage = @"the soap message"; //website and soapmessage are valid in original code. NSError **error; NSURLResponse *response; //Convert parameter string to url NSURL *url = [NSURL URLWithString:requestUrl]; NSMutableURLRequest *theRequest = [NSMutableURLRequest requestWithURL:url cachePolicy:NSURLRequestReloadIgnoringCacheData timeoutInterval:10]; NSString *msgLength = [NSString stringWithFormat:@"%d", [soapMessage length]]; //Create an XML message for webservice [theRequest addValue: @"text/xml; charset=utf-8" forHTTPHeaderField:@"Content-Type"]; [theRequest addValue: msgLength forHTTPHeaderField:@"Content-Length"]; [theRequest setHTTPMethod:@"POST"]; [theRequest setHTTPBody: [soapMessage dataUsingEncoding:NSUTF8StringEncoding]]; NSData *webData = [NSURLConnection sendSynchronousRequest:theRequest returningResponse:&response error:error]; } I tried not to release a thing, because what i read on the net is it's almost always a memory thing. When i debug the code (NSZombieEnabled = YES) this is what i get: [Session started at 2010-05-31 15:56:13 +0200.] GNU gdb 6.3.50-20050815 (Apple version gdb-1461.2) (Fri Mar 5 04:43:10 UTC 2010) Copyright 2004 Free Software Foundation, Inc. GDB is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. Type "show copying" to see the conditions. There is absolutely no warranty for GDB. Type "show warranty" for details. This GDB was configured as "x86_64-apple-darwin".sharedlibrary apply-load-rules all Attaching to process 19856. test(19856) malloc: recording malloc stacks to disk using standard recorder test(19856) malloc: enabling scribbling to detect mods to free blocks test(19856) malloc: process 19832 no longer exists, stack logs deleted from /tmp/stack-logs.19832.test.w9Ek4L.index test(19856) malloc: stack logs being written into /tmp/stack-logs.19856.test.URRpQF.index Program received signal: “EXC_BAD_ACCESS”. Does anybody have a clue?? Thanks a lot! Lars

    Read the article

  • Wordpress form handling

    - by Ron
    I need to add a basic form page in the website, that runs on WordPress framework. I have the following raw materials ready: Client side: html form layout,css and jquery validation code. Server side: form handler php function that processes the $_POST[] data. My problem is to integrate this code in the Wordpress framework. I have looked at some plugins but they are doing much more than I would like and also they have their own validation which is cumbersome to change. Could anyone suggest a good form plugin that allows just the framework hooks ? Or is it worthwhile that I should write the plugin myself. Thanks.

    Read the article

  • using WP_Query with custom SQL in wordpress

    - by Matt Facer
    Hi. I am writing a plugin for wordpress and I want to create my own search. I have tried to alter the wordpress search, but what I am doing is very specific with the SQL query. I am comparing lat and long coordinates and getting posts based on that. I can display posts by using the standard wpdb query, but then I don't get the other features like paging. I'd like to be able to use my SQL statement with the WP_Query function. If I'm right in thinking, I should then be able to use the paging and other features which come from the $posts global variable. Is this right?? I've googled for hours but can't find anything for plugins outside of using args to select categories etc. I simply need to send a complete SQL command - nothing else. Many thanks....

    Read the article

  • Casting problems with Google Maps API

    - by Thiago
    Hi there, I'm trying to run the following line: Directions.loadFromWaypoints((Waypoint[])waypoints.toArray(), opts); But I'm getting: 23:41:44.595 [ERROR] [carathome] Uncaught exception escaped java.lang.ClassCastException: [Ljava.lang.Object; cannot be cast to [Lcom.google.gwt.maps.client.geocode.Waypoint; at com.presasystems.gwt.carathome.client.widgets.MostrarLinhasPanel$1$1.onSuccess(MostrarLinhasPanel.java:72) at com.presasystems.gwt.carathome.client.widgets.MostrarLinhasPanel$1$1.onSuccess(MostrarLinhasPanel.java:1) at com.google.gwt.user.client.rpc.impl.RequestCallbackAdapter.onResponseReceived(RequestCallbackAdapter.java:216) at com.google.gwt.http.client.Request.fireOnResponseReceived(Request.java:287) at com.google.gwt.http.client.RequestBuilder$1.onReadyStateChange(RequestBuilder.java:393) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source) at java.lang.reflect.Method.invoke(Unknown Source) at com.google.gwt.dev.shell.MethodAdaptor.invoke(MethodAdaptor.java:103) at com.google.gwt.dev.shell.MethodDispatch.invoke(MethodDispatch.java:71) at com.google.gwt.dev.shell.OophmSessionHandler.invoke(OophmSessionHandler.java:157) at com.google.gwt.dev.shell.BrowserChannel.reactToMessagesWhileWaitingForReturn(BrowserChannel.java:1713) at com.google.gwt.dev.shell.BrowserChannelServer.invokeJavascript(BrowserChannelServer.java:165) at com.google.gwt.dev.shell.ModuleSpaceOOPHM.doInvoke(ModuleSpaceOOPHM.java:120) at com.google.gwt.dev.shell.ModuleSpace.invokeNative(ModuleSpace.java:507) at com.google.gwt.dev.shell.ModuleSpace.invokeNativeObject(ModuleSpace.java:264) at com.google.gwt.dev.shell.JavaScriptHost.invokeNativeObject(JavaScriptHost.java:91) at com.google.gwt.core.client.impl.Impl.apply(Impl.java) at com.google.gwt.core.client.impl.Impl.entry0(Impl.java:188) at sun.reflect.GeneratedMethodAccessor9.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source) at java.lang.reflect.Method.invoke(Unknown Source) at com.google.gwt.dev.shell.MethodAdaptor.invoke(MethodAdaptor.java:103) at com.google.gwt.dev.shell.MethodDispatch.invoke(MethodDispatch.java:71) at com.google.gwt.dev.shell.OophmSessionHandler.invoke(OophmSessionHandler.java:157) at com.google.gwt.dev.shell.BrowserChannel.reactToMessages(BrowserChannel.java:1668) at com.google.gwt.dev.shell.BrowserChannelServer.processConnection(BrowserChannelServer.java:401) at com.google.gwt.dev.shell.BrowserChannelServer.run(BrowserChannelServer.java:222) at java.lang.Thread.run(Unknown Source) Why? Shouldn't this cast work? How can I do this in an elegant fashion? Thanks in advance

    Read the article

  • I need to block my feed completly

    - by justjoe
    i'm in need a solution via coding. on how to completely hide my blog feed. I know how to optimize related hook and filter such as 'the_excerpt_rss' and 'the_post_rss'. And also understand how to limit access or make my blog private. so, the question is more about howto blocking feed access without make my blog private ? i hope the solution will be not some apache .htacceess. Cause i need to code it directly into my theme.. sorry if this's too much to asked.

    Read the article

  • When is it safe to remote import entires from feature.xml?

    - by Robert Munteanu
    I've recently learned that the import section from feature.xml is legacy, and the actual dependency work is delegated to the p2 engine, which uses the information from the plugin manifest. I am not sure though if p2 is available for all recent versions of Eclipse, or in all Eclipse-based products, so I'm not sure if it is safe to remove the import section from feature.xml. Under what circumstances is it safe to remove the import section from feature.xml? Assume that we are taking into consideration Eclipse 3.4 or newer.

    Read the article

  • WP plugin based on useragent

    - by jake
    I am writing a plugin which does some js stuff, but does not work for other browsers than FF . I've thought why not execute the plugin for the browsers which support it. I've added the code, but for some reason when I activate the plugin and check the site with a FF all I get is blank page. If I visit with a IE the site is shown correctly. Basically my code is like this $agent= strtolower($_SERVER['HTTP_USER_AGENT']); if (preg_match('/firefox/',$agent)){ include(plugins_url('script.js',FILE)); some more code } So when I visit with FF I get blank page, when I visit with IE the blog loads normally

    Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >