Search Results

Search found 48774 results on 1951 pages for 'linux development'.

Page 26/1951 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• 64-bit 13.10 shows 1GB less RAM than 64-bit 13.04 did

  - by kiloseven

  Multiple 64-bit versions (Kubuntu, Lubuntu and Xubuntu) once installed on my ThinkPad R60 show 3GB of RAM, not the correct 4GB of RAM. Last week with 13.04, I had 4GB of RAM (which matches the BIOS) and this week I have 3GB available. Inquiring minds want to know. Details follow: Linux R60 3.11.0-12-generic #19-Ubuntu SMP Wed Oct 9 16:20:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux r60 free -m reports: _ total used free shared buffers cached Mem: 3001 854 2146 0 22 486 -/+ buffers/cache: 346 2655 Swap: 0 0 0 . . . . . . lshw shows: description: Notebook product: 9459AT8 () vendor: LENOVO version: ThinkPad R60/R60i serial: redacted width: 64 bits capabilities: smbios-2.4 dmi-2.4 vsyscall32 configuration: administrator_password=disabled boot=normal chassis=notebook family=ThinkPad R60/R60i frontpanel_password=unknown keyboard_password=disabled power-on_password=disabled uuid=126E4001-48CA-11CB-9D53-B982AE0D1ABB *-core description: Motherboard product: 9459AT8 vendor: LENOVO physical id: 0 version: Not Available *-firmware description: BIOS vendor: LENOVO physical id: 0 version: 7CETC1WW (2.11 ) date: 01/09/2007 size: 144KiB capacity: 1984KiB capabilities: pci pcmcia pnp upgrade shadowing escd cdboot bootselect socketedrom edd acpi usb biosbootspecification {snip} *-memory description: System Memory physical id: 29 slot: System board or motherboard size: 4GiB *-bank:0 description: SODIMM DDR2 Synchronous physical id: 0 slot: DIMM 1 size: 2GiB width: 64 bits *-bank:1 description: SODIMM DDR2 Synchronous physical id: 1 slot: DIMM 2 size: 2GiB width: 64 bits dpkg -l linux-* returns: Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Description +++-======================================-=======================================-========================================================================== un linux-doc-3.2.0 (no description available) ii linux-firmware 1.79.6 Firmware for Linux kernel drivers ii linux-generic 3.2.0.52.62 Complete Generic Linux kernel un linux-headers (no description available) un linux-headers-3 (no description available) un linux-headers-3.0 (no description available) un linux-headers-3.2.0-23 (no description available) un linux-headers-3.2.0-23-generic (no description available) ii linux-headers-3.2.0-52 3.2.0-52.78 Header files related to Linux kernel version 3.2.0 ii linux-headers-3.2.0-52-generic 3.2.0-52.78 Linux kernel headers for version 3.2.0 on 64 bit x86 SMP ii linux-headers-generic 3.2.0.52.62 Generic Linux kernel headers un linux-image (no description available) un linux-image-3.0 (no description available) ii linux-image-3.2.0-52-generic 3.2.0-52.78 Linux kernel image for version 3.2.0 on 64 bit x86 SMP ii linux-image-generic 3.2.0.52.62 Generic Linux kernel image un linux-initramfs-tool (no description available) un linux-kernel-headers (no description available) un linux-kernel-log-daemon (no description available) ii linux-libc-dev 3.2.0-52.78 Linux Kernel Headers for development un linux-restricted-common (no description available) ii linux-sound-base 1.0.25+dfsg-0ubuntu1.1 base package for ALSA and OSS sound systems un linux-source-3.2.0 (no description available) un linux-tools (no description available)

  Read the article

• How to use more than 3 virtual disks in Linux using CentOS and XenServer

  - by 010110110101

  I've attached 5 virtual disks to a Virtual Machine in Citrix XenServer. The VM has the xs-tools installed. Initially it said that it couldn't add so many disks. After I installed the xs-tools, it let me add all the disks. But /dev doesn't show all the disks. It shows these: /dev/xvda /dev/xvdb /dev/xvdc /dev/cdrom Perhaps it is bound by the limits of an IDE bus? (3 disks + CD-ROM) If so, how does one change the VM to use SCSI? Edit: According to the documentation: 2.6.3. VM Block Devices In the PV Linux case, block devices are passed through as PV devices. XenServer does not attempt to emulate SCSI or IDE, but instead provides a more suitable interface in the virtual environment in the form of xvd* devices. It is also possible to get an sd* device using the same mechanism, where the PV driver inside the VM takes over the SCSI device namespace. This is not desirable so it is best to use xvd* where possible for PV guests (this is the default for Debian and RHEL). For Windows or other fully virtualized guests, XenServer emulates an IDE bus in the form of an hd* device. When using Windows, installing the Citrix Tools for Virtual Machines installs a special PV driver that works in a similar way to Linux, except in the fully virtualized environment. Still, with 5 virtual disks attached, I don't see the other xvd devices. Edit #2: (attached requested info) Host Machine: XenServer 6.1 Linux version 2.6.32.43-0.4.1.xs1.6.10.777.170770xen (geeko@buildhost) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-51)) #1 SMP Wed Apr 17 05:52:03 EDT 2013 Guest Machine: CentOS release 6.4 (Final) Linux version 2.6.32-358.6.2.el6.x86_64 ([email protected]) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Thu May 16 20:59:36 UTC 2013 Output of 'fdisk -l' on Guest Machine: Note, the disk beyond the first 3 attached are not displaying -- there should be 4 100GB disks. (There are a total of 5 disks displayed in XenCenter -- 16GB, 100GB, 100GB, 100GB, 100GB) Disk /dev/xvdb: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xfb6c95b9 Device Boot Start End Blocks Id System /dev/xvdb1 1 13054 104856223+ 83 Linux Disk /dev/xvda: 17.2 GB, 17179869184 bytes 255 heads, 63 sectors/track, 2088 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e5f41 Device Boot Start End Blocks Id System /dev/xvda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/xvda2 64 2089 16264192 8e Linux LVM Disk /dev/xvdc: 107.4 GB, 107374182400 bytes 255 heads, 63 sectors/track, 13054 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xed249ced Device Boot Start End Blocks Id System /dev/xvdc1 1 13054 104856223+ 83 Linux Disk /dev/mapper/vg_blue-lv_root: 14.6 GB, 14571012096 bytes 255 heads, 63 sectors/track, 1771 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_blue-lv_swap: 2080 MB, 2080374784 bytes 255 heads, 63 sectors/track, 252 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 I see that the Linux versions say SMP. The Guest VM doesn't say "xen" in the name. However, I have already run yum install kernel-xen. Could be a clue?

  Read the article

• Non-language-specific interview questions for a senior web developer

  - by Songo

  I came across a job posting for a senior web developer position. The posting said that the development will be done using Ruby on Rails, but no prior knowledge is required. I confirmed with a contact in that company that a PHP web developer can apply for it or even an ASP.Net developer. I also confirmed that the interview won't contain any questions specific to PHP or Ruby on Rails. Can anyone please provide a good list of questions for a senior web developer that isn't specific to a certain language? Note This question isn't a duplicate for similar posts asking for questions relating to PHP, .Net or Ruby. Also, I'm not looking for topics to learn as a web developer, but rather interesting questions for a technical interview given the former conditions.

  Read the article

• Future of Programmers [closed]

  - by Brian Paul

  Possible Duplicate: Will programmers be around in a few years? I have a passion of web development, but have been wondering of late, what is the future of web programming, and just programming in general. I will give an example to illustrate this, companies now most of them buy/ are willing to spend more money to implement enterprise level products, coming from big companies, than hiring a programmer, because when you look at the long term,instead of paying this programmer, and being tied to his ideas and skills, better buy a product, which you are guaranteed high level functions and support. Therefore what will be the future to programmers?

  Read the article

• When Programming will become deprecated [closed]

  - by Vibeeshan

  Possible Duplicate: Will programmers be around in a few years? According to the history of programming, with each new generation of software engineering it seems to become easier and easier. Machine Code - Assembly - Programming Languages - easier - more easier - etc. If this situation continues anyone will be able to program (even complex systems). Even now, most of the kids study programming at school (Pascal , VB, etc.). Will be there any jobs called software engineering in future (if everyone know to program). ....and.... What do you think about the future of software development?

  Read the article

• What to do with database in dev/production phases of a website?

  - by TheLQ

  For a while now I've been keeping a website I'm developing in the standard dev/production phases. Its been pretty simple: Mercurial repo for dev, repo for production. Do work in dev, get approved, push to production. But now I'm trying to apply this process to a new website that has a database and am struggling on how to figure out a development strategy. What I didn't mention above is that I do all my work on my own repo, push it to dev, then later push it to production, so its 3 different servers. So how do I manage my database? The obvious solution of mysqldump every commit isn't going to happen, and a dump at the end of the day isn't all that helpful when you want to undo later one change that happened in the middle of the day. What is the best way to accomplish this?

  Read the article

• SAP vs Other Technologies

  - by Bunny Rabbit

  I am a fresher just out of collge .Till now i have worked on java,Python,javascript,groovy,django,JS, JQuery and web application develop has been my only intrest. I have been working for an IT company for past three months and it involves working with an erp package SAP and i am working on ABAP. Coming from a world of ORM and languages like python ,SAP and database tables doen't excite me much. With all the development being happening around HTML 5 and android etc i feel quite left out and bored in SAP . can you guys suggest me a proper way forward ?

  Read the article

• How to understand Linux kernel source code for a beginner?

  - by Amit Chavan

  Hi, I am a student interested in working on Memory Management, particularly the page replacement component of the linux kernel. What are the different guides that can help me to begin understanding the kernel source? I have tried to read the book Understanding the Linux Virutal Memory Manager by Mel Gorman and Understanding the Linux Kernel by Cesati and Bovet, but they do not explain the flow of control through the code. They only end up explaining various data structures used and the work various functions perform. This makes the code more confusing. My project deals with tweaking the page replacement algorithm in a mainstream kernel and analyse its performance for a set of workloads. Is there a flavor of the linux kernel that would be easier to understand(if not the linux-2.6.xx kernel)?

  Read the article

• Is there much difference between X86 Assembly language on Windows and Linux?

  - by Logan545

  I'm a complete beginner at Assembly, and my aim is to learn as much as I can to do with Assembly to one day I can reach expert level (I know I'm way off right now, but you never know). My only problem is this: I've got two books which both teach assembly, one on a Linux and the other on Windows. They are Jeff Duntemann's Assembly Language Step By Step (the linux one) and Introduction to 80x86 Assembly Language and Computer Architecture (the windows version). If I want to get the best out of assembly, should I do this on linux and windows? Also, is the syntax the same on Windows and Linux or will I have teach my self again when learning on the other OS( which is my main concern, I want to be able to use assembly on windows and linux).

  Read the article

• How to understand Linux kernel source code for a beginner?

  - by user16867

  I am a student interested in working on Memory Management, particularly the page replacement component of the linux kernel. What are the different guides that can help me to begin understanding the kernel source? I have tried to read the book Understanding the Linux Virutal Memory Manager by Mel Gorman and Understanding the Linux Kernel by Cesati and Bovet, but they do not explain the flow of control through the code. They only end up explaining various data structures used and the work various functions perform. This makes the code more confusing. My project deals with tweaking the page replacement algorithm in a mainstream kernel and analyse its performance for a set of workloads. Is there a flavor of the linux kernel that would be easier to understand(if not the linux-2.6.xx kernel)?

  Read the article

• Advice: should I focus on PHP + MySQL, or split my time for more JS and CSS? [closed]

  - by fakaff

  I started learning web development about three months ago (in between working my regular job), and I'm finally starting to get some vague, distant notion of understanding. I find the server-side stuff the most interesting; though I've not gone anywhere near Apache quite yet, which I assume will be necessary at some point. As cool as toying around with visuals and UI is, programming and database stuff inspires me with new ideas and possibilities every minute (I've even bought, on a whim, a wonderfully dry bunch of books on database theory and relational algebra). And whatever CSS or Javascript tutorial I'm doing, it often feels like a distraction from the PHP/MySQL stuff I'd rather be playing with. For someone like me who's just starting out, which is the most advisable course of action? (in terms of being marketable as a programmer): To focus on PHP and SQL stuff exclusively, and only once I master those to diversify my skills. To first learn all three (PHP/MySQL, Javascript, CSS and design) and only once I'm fluent in all three focus on PHP and databases?

  Read the article

• Linux UML - Need gcc on the UML instance. Would like to mount gcc from hostfs

  - by Zach

  I know how to mount the hostfs directories when needed for my UML Linux instance. I need to get gcc and all it's dependencies from my host Linux instance by mounting the files in my UML instance. I think the paths are not working properly because it comes up with an error about cc1 and execvp when I mount all files and try to run gcc. Any ideas? Thanks!

  Read the article

• GRE keepalive with Linux and RouterOS

  - by eri

  I have a Linux host and couple of routerboadrs. I created a GRE tunnel, but Linux does not answer keepalive packages. Then router mark gre connection as unreachable, so I cant send to Linux host from router subnet. If linux sends something into tunnel (ping, etc.) - RouterOS mark connection as reacheble. Second and next packages routed nicely until one minute idle (no traffic). Tunnel in linux a make in this way: remote=x.x.x.x dev=gre21 network=10.21.0.0/16 ip tunnel add ${dev} mode gre remote ${remote} ttl 255 ip addr add 172.16.1.1/24 peer 172.16.1.21 dev ${dev} ip link set ${dev} up ip route add ${network} dev ${dev} And ip l: 14: gre21: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN link/gre 0.0.0.0 peer 109.60.170.15 How to set state "running"? How to keep alive tunnel? Ping in cron?

  Read the article

• How to use suse linux as a small router

  - by Mingo

  I has 2 subnet 192.168.1.0/24 and 192.168.2.0/24 and one suse linux, the linux has 2 interface, eth0 and eth1. I want to configurate the suse linux as a router so that make these 2 subnet can communicate with each other. This is my steps: 1.set the linux eth0 ip as 192.160.1.254,eth1 ip 192.168.2.254 2.add route in linux: route add -net 192.168.1.0 netmask 255.255.255.0 dev eth0 route add -net 192.168.2.0 netmask 255.255.255.0 dev eth1 3.set 192.168.1.0/24 gw as 192.168.1.254,and 192.168.2.0/24 gw as 192.168.2.254 I am not sure this will work or not? or some step i missing?

  Read the article

• Untar after uploading to linux from windows

  - by Miqdad Ali

  I have created tar.gz from my linux server, and I downloaded the same to my linux system and I successfully doen untar with tar -xvf package.tar.gz. And now my issue I downloaded same package.tar.gz to the windows system then uploaded to another linux server, and tried same command tar -xvf package.tar.gz. but it getting tar: This does not look like a tar archive tar: Skipping to next header tar: Exiting with failure status due to previous errors as response. I also tried filezill manual trnasfer with binary mode. How can I do the same ? Update When I directly download to the linux system its working fine. When I downloaded to the windows system and try to extract with 7zip or winrar error is getting When I download to windows and upload to linux same error getting

  Read the article

• Put a Windows computer to sleep remotely (from a Linux box)

  - by snark

  I'd like to have my Linux box (a QNAP TS-210 NAS) send the order to go to sleep (or hibernation) to my main Windows 7 computer. As the NAS is running Linux, I can't use psshutdown from SysInternals' PsTools. Is there any Linux equivalent? Or some "magic packet" that can order the Win7 computer to sleep. I know I could install a SSH daemon and trigger a shutdown command from the Linux box using ssh, but ideally I do not want to install anything on the Win7 computer. I can install Linux software on the NAS, no problem about this. PHP, python and perl are also available on it.

  Read the article

• Publishing and setting permissions to a Linux share to AD

  - by blsub6

  I have a Linux share that I want to publish to users on my Active Directory domain. I'd like to be able to control the permissions to access that share using security groups. So say I have a share named "Share" on my Linux machine named "Linux" with IP address 192.168.1.2. I publish \\192.168.1.2\Share in AD and make it so that only people who are part of the "IT" security group can access it. What's to stop anyone who's not in the "IT" security group from just going to explorer and typing in \\192.168.1.2\Share or \\Linux\Share into their Explorer to access this share? Do I need to set up permissions on the Linux file server?

  Read the article

• How to make schema dumps comparable between Windows and Linux

  - by Jonathan

  I have two systems running, one on linux and the other on windows. From the linux box, I ran pg_dump against both systems and dumped the schema. pg_dump command: pg_dump -h HOST -U USER -s -f /tmp/out.sql DB_NAME After I removed all of the "--" comments, I diffed the files together. Diff output snippet, linux compared to windows: - ADD CONSTRAINT sys_c004775 FOREIGN KEY (ruleid) REFERENCES rule(ruleid); + ADD CONSTRAINT sys_c004775 FOREIGN KEY (ruleid) REFERENCES "rule"(ruleid); The linux dump does not quote any entities and windows does. Is this a function of some encoding or just of a difference between windows and linux? Is there an option in pg_dump to make the output more consistent?

  Read the article

• Minimal Linux distribution with sshd and apt

  - by Sergey Mikhanov

  When I signed up for my Debian Linux VPS hosting and first logged on and invoked ps, there was the only user process running: sshd. As I can see, this was minimal Linux with only two things installed and configured: sshd and apt (plus all dependencies, of course). I want to build (or use existing) similar Linux distro, any advice on how to build (or pick) one? Googling "minimum linux", or "linux with sshd only" usually brings up Debian's netinstall, which is not what I want. Thanks in advance.

  Read the article

• printing in linux

  - by Neilvert Noval

  Hello all. I've been a linux user for quite some time. But haven't do printing until now. I just wanna ask how to do printing in linux? I have researched a bit on it. I found some $> echo "print me" > /dev/lp0, but unfortunately, I have no lp0 in my /dev. I don't know if this is the right thing to do. Nevertheless, please tell me of ways on how I can print from my linux box. Here are some details: OS: debian linux 5.0.4 printer: disclosed until it is necessary connection: usb connection So do i need to add a printer first? From the printer manual that I read, this printer model has no linux driver.

  Read the article

• Setting up a linux switch

  - by Shahmir Javaid

  I have a C++ Program to sniff each and every packet that crosses my linux box. However i need to now get my linux box to listen to every traffic in my network. I could buy a managed switch and set up port spanning, but i aint paying 200+ £'s for a switch and plus gives me a chance to learn. My Network +---------Computer A | Internet-----Router------Switch-------------+---------Linux Box | +---------Computer B Proposed Network +---------Computer A | Internet-----Router------Linux Box--------Switch eth0^ ^eth1 | +---------Computer B How would i setup this in linux. Do i just configure both the ethernet on different IP Address on the same network. Or am i completelly on the wrong track My System Fedora 13. Thanks

  Read the article

• SSD runs faster on Windows as compared to Linux [closed]

  - by wushugene

  Windows 7 seems to install, boot and run much smoother & faster than each the three linux distros I have recently tried (Ubuntu 12.04 unity, Linux mint 13 MATE, and Fedora 17 on gnome 3.4). Why am I facing bad performance in Linux? I have tweaked my Linux installs for the SSD (enabling trim, disabling swap, etc.) I'm using an Acer TravelMate with i5-2410m processor, intel hd 3000 graphics, 8 gigs of ram, and a 256 gb samsung 830 ssd. Edit: Boot times are 10-15 seconds slower, there is noticeable delay from login to fully loaded desktop, and in general does not appear to be as responsive as my old windows 7 install or the Linux guests I had running on it.

  Read the article

• Can't boot Windows after installing Linux

  - by user4035

  I have a partition /dev/sdb1, where my old Windows XP resides. All the files are there intact and I can see them, mounting the disk from Linux. Linux is on /dev/sdb2. But when I choose Windows in LILO prompt, it doesn't load. I have the following lilo.conf: boot = /dev/sdb # Linux bootable partition config begins image = /boot/vmlinuz root = /dev/sdb2 label = Linux read-only # Partitions should be mounted read-only for checking # Linux bootable partition config ends # Windows bootable partition config begins other = /dev/sdb1 label = Windows table = /dev/sdb # Windows bootable partition config ends What can be wrong?

  Read the article

• Can't make AWUS036H work in Ubuntu 12.10

  - by sfrj

  I am using 64 bit Ubuntu 12.10. This is my kernel version: Linux 3.5.0-19-generic #30-Ubuntu SMP Tue Nov 13 17:48:01 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux My wireless card is an AWUSU36H The first thing I do to install the driver is copy the driver from the CD to the Downloads folder. cd /media/me/AWUS036H/Drivers/RTL8187L/Unix (Linux)/Linux driver for kernel 2.6.X$ cp rtl8187_linux_26.1025.0328.2007.tar.gz ~/Downloads/ Then I extract the tar tar xvfz rtl8187_linux_26.1025.0328.2007.tar.gz I navigate into the extracted folder, and I try to follow the instructions in the Readme.txt cd rtl8187_linux_26.1025.0328.2007 This are the contents of the folder: drv.tar.gz makedrv stack.tar.gz wlan0rmv ieee80211 ReadMe.txt wlan0dhcp wlan0up ifcfg-wlan0 rtl8187 wlan0down wpa_supplicant-0.4.9 This is what the Readme.txt says: Release Date: 2006-02-09, ver 1.2^M RTL8187 Linux driver version 1.2^M ^M --This driver supports RealTek RTL8187 Wireless LAN driver for ^M Fedora Core 2/3/4/5, Debian 3.1, Mandrake 10.2/Mandriva 2006, ^M SUSE 9.3/10.1/10.2, Gentoo 3.1, etc.^M - Support Client mode for either infrastructure or adhoc mode^M - Support WEP and WPAPSK connection^M ^M < Component >^M The driver is composed of several parts:^M 1. Module source code^M stack.tar.gz^M drv.tar.gz^M ^M 2. Script ot build the modules^M makedrv^M ^M 3. Script to load/unload modules^M wlan0up^M wlan0down ^M ^M 4. Script and configuration for DHCP^M "ReadMe.txt" [readonly] 140 lines, 4590 characters So what I do know is extract both of the compressed files: sudo tar xvfz drv.tar.gz sudo tar xvfz stack.tar.gz This 2 commands will add some data to the folders ieee80211 and rtl8187 At this point I get lost, and I don't know what to do. If I go in each of this 2 folders and I run the sudo make command then I get errors like this one: sudo makemake -C /lib/modules/3.5.0-19-generic/build M=/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187 modules make[1]: Entering directory `/usr/src/linux-headers-3.5.0-19-generic' CC [M] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.o In file included from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.c:64:0: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187.h:29:26: fatal error: linux/config.h: No such file or directory compilation terminated. make[2]: *** [/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.o] Error 1 make[1]: *** [_module_/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.5.0-19-generic' make: *** [modules] Error 2 If I try to run any of the script ./makedrv that the instructions describe, then I also get an error: ~/Downloads/rtl8187_linux_26.1025.0328.2007$ sudo ./makedrv [sudo] password for me: ieee80211/ ieee80211/license ieee80211/ieee80211_crypt.c ieee80211/ieee80211_tx.c ieee80211/ieee80211_softmac.c ieee80211/ieee80211_softmac_wx.c ieee80211/ieee80211_module.c ieee80211/ieee80211_crypt_ccmp.c ieee80211/ieee80211_rx.c ieee80211/tags ieee80211/ieee80211_crypt_tkip.c ieee80211/Makefile ieee80211/readme ieee80211/.tmp_versions/ ieee80211/.tmp_versions/ieee80211-rtl.mod ieee80211/.tmp_versions/ieee80211_crypt_wep-rtl.mod ieee80211/.tmp_versions/ieee80211_crypt_tkip-rtl.mod ieee80211/.tmp_versions/ieee80211_crypt-rtl.mod ieee80211/.tmp_versions/ieee80211_crypt_ccmp-rtl.mod ieee80211/ieee80211_crypt_wep.c ieee80211/ieee80211.h ieee80211/ieee80211_wx.c ieee80211/ieee80211_crypt.h rtl8187/ rtl8187/license rtl8187/r8180_rtl8225z2.c rtl8187/r8180_rtl8225.h rtl8187/r8187_led.c rtl8187/r8180_93cx6.h rtl8187/r8180_wx.h rtl8187/r8180_hw.h rtl8187/copying rtl8187/r8187_led.h rtl8187/r8180_pm.h rtl8187/tags rtl8187/r8187.h rtl8187/Makefile rtl8187/r8180_rtl8225.c rtl8187/readme rtl8187/install rtl8187/.tmp_versions/ rtl8187/.tmp_versions/r8187.mod rtl8187/changes rtl8187/r8180_wx.c rtl8187/r8180_pm.c rtl8187/r8187_core.c rtl8187/r8180_93cx6.c rtl8187/authors rtl8187/ieee80211.h rtl8187/ieee80211_crypt.h rm -f *.mod.c *.mod *.o .*.cmd *.ko *~ rm -rf /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/tmp make -C /lib/modules/3.5.0-19-generic/build M=/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211 modules make[1]: Entering directory `/usr/src/linux-headers-3.5.0-19-generic' CC [M] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.o In file included from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17:0: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:1019:24: error: field ‘ps_task’ has incomplete type /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_softmac_scan_wq’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:421:2: warning: passing argument 2 of ‘queue_delayed_work’ from incompatible pointer type [enabled by default] In file included from include/linux/srcu.h:32:0, from include/linux/notifier.h:15, from /usr/src/linux-headers-3.5.0-19-generic/arch/x86/include/asm/uprobes.h:26, from include/linux/uprobes.h:35, from include/linux/mm_types.h:15, from include/linux/kmemcheck.h:4, from include/linux/skbuff.h:18, from include/linux/if_ether.h:134, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:26, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17: include/linux/workqueue.h:371:12: note: expected ‘struct delayed_work *’ but argument is of type ‘struct work_struct *’ /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_softmac_stop_scan’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:495:3: warning: passing argument 1 of ‘cancel_delayed_work’ from incompatible pointer type [enabled by default] In file included from include/linux/srcu.h:32:0, from include/linux/notifier.h:15, from /usr/src/linux-headers-3.5.0-19-generic/arch/x86/include/asm/uprobes.h:26, from include/linux/uprobes.h:35, from include/linux/mm_types.h:15, from include/linux/kmemcheck.h:4, from include/linux/skbuff.h:18, from include/linux/if_ether.h:134, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:26, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17: include/linux/workqueue.h:410:20: note: expected ‘struct delayed_work *’ but argument is of type ‘struct work_struct *’ /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_associate_abort’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:915:2: warning: passing argument 2 of ‘queue_delayed_work’ from incompatible pointer type [enabled by default] In file included from include/linux/srcu.h:32:0, from include/linux/notifier.h:15, from /usr/src/linux-headers-3.5.0-19-generic/arch/x86/include/asm/uprobes.h:26, from include/linux/uprobes.h:35, from include/linux/mm_types.h:15, from include/linux/kmemcheck.h:4, from include/linux/skbuff.h:18, from include/linux/if_ether.h:134, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:26, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17: include/linux/workqueue.h:371:12: note: expected ‘struct delayed_work *’ but argument is of type ‘struct work_struct *’ /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_rx_frame_softmac’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:1527:3: error: implicit declaration of function ‘tasklet_schedule’ [-Werror=implicit-function-declaration] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_stop_protocol_rtl’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2120:2: warning: passing argument 1 of ‘cancel_delayed_work’ from incompatible pointer type [enabled by default] In file included from include/linux/srcu.h:32:0, from include/linux/notifier.h:15, from /usr/src/linux-headers-3.5.0-19-generic/arch/x86/include/asm/uprobes.h:26, from include/linux/uprobes.h:35, from include/linux/mm_types.h:15, from include/linux/kmemcheck.h:4, from include/linux/skbuff.h:18, from include/linux/if_ether.h:134, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:26, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17: include/linux/workqueue.h:410:20: note: expected ‘struct delayed_work *’ but argument is of type ‘struct work_struct *’ /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_softmac_init’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2229:78: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2229:2: error: ‘INIT_WORK’ undeclared (first use in this function) /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2229:2: note: each undeclared identifier is reported only once for each function it appears in /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2230:88: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2231:94: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2232:96: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2233:82: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2234:82: error: macro "INIT_WORK" passed 3 arguments, but takes just 2 /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2244:2: error: implicit declaration of function ‘tasklet_init’ [-Werror=implicit-function-declaration] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_softmac_free’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2255:2: warning: passing argument 1 of ‘cancel_delayed_work’ from incompatible pointer type [enabled by default] In file included from include/linux/srcu.h:32:0, from include/linux/notifier.h:15, from /usr/src/linux-headers-3.5.0-19-generic/arch/x86/include/asm/uprobes.h:26, from include/linux/uprobes.h:35, from include/linux/mm_types.h:15, from include/linux/kmemcheck.h:4, from include/linux/skbuff.h:18, from include/linux/if_ether.h:134, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:26, from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17: include/linux/workqueue.h:410:20: note: expected ‘struct delayed_work *’ but argument is of type ‘struct work_struct *’ /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: In function ‘ieee80211_wpa_set_encryption’: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2489:3: error: implicit declaration of function ‘request_module’ [-Werror=implicit-function-declaration] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2518:3: error: implicit declaration of function ‘try_module_get’ [-Werror=implicit-function-declaration] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c: At top level: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2663:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2663:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2663:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2664:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2664:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2664:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2665:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2665:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2665:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2666:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2666:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2666:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2667:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2667:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2667:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2668:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2668:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2668:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2669:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2669:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2669:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2670:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2670:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2670:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2671:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2671:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2671:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2672:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2672:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2672:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2673:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2673:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2673:1: warning: parameter names (without types) in function declaration [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2674:1: warning: data definition has no type or storage class [enabled by default] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2674:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’ [-Wimplicit-int] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:2674:1: warning: parameter names (without types) in function declaration [enabled by default] In file included from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.c:17:0: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211.h:1212:37: warning: ‘netdev_priv’ is static but used in inline function ‘ieee80211_priv’ which is not static [enabled by default] cc1: some warnings being treated as errors make[2]: *** [/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211/ieee80211_softmac.o] Error 1 make[1]: *** [_module_/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/ieee80211] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.5.0-19-generic' make: *** [modules] Error 2 rm -f *.mod.c *.mod *.o .*.cmd *.ko *~ rm -rf /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/tmp make -C /lib/modules/3.5.0-19-generic/build M=/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187 modules make[1]: Entering directory `/usr/src/linux-headers-3.5.0-19-generic' CC [M] /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.o In file included from /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.c:64:0: /home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187.h:29:26: fatal error: linux/config.h: No such file or directory compilation terminated. make[2]: *** [/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187/r8187_core.o] Error 1 make[1]: *** [_module_/home/me/Downloads/rtl8187_linux_26.1025.0328.2007/rtl8187] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.5.0-19-generic' make: *** [modules] Error 2 Can somebody give me a hand finding out what I need to do to make my wifi card work? Update This is the output of the lsusb command lsusb Bus 003 Device 002: ID 147e:1000 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

  Read the article

• Announcing Unbreakable Enterprise Kernel Release 3 for Oracle Linux

  - by Lenz Grimmer

  We are excited to announce the general availability of the Unbreakable Enterprise Kernel Release 3 for Oracle Linux 6. The Unbreakable Enterprise Kernel Release 3 (UEK R3) is Oracle's third major supported release of its heavily tested and optimized Linux kernel for Oracle Linux 6 on the x86_64 architecture. UEK R3 is based on mainline Linux version 3.8.13. Some notable highlights of this release include: Inclusion of DTrace for Linux into the kernel (no longer a separate kernel image). DTrace for Linux now supports probes for user-space statically defined tracing (USDT) in programs that have been modified to include embedded static probe points Production support for Linux containers (LXC) which were previously released as a technology preview Btrfs file system improvements (subvolume-aware quota groups, cross-subvolume reflinks, btrfs send/receive to transfer file system snapshots or incremental differences, file hole punching, hot-replacing of failed disk devices, device statistics) Improved support for Control Groups (cgroups)  The ext4 file system can now store the content of a small file inside the inode (inline_data) TCP fast open (TFO) can speed up the opening of successive TCP connections between two endpoints FUSE file system performance improvements on NUMA systems Support for the Intel Ivy Bridge (IVB) processor family Integration of the OpenFabrics Enterprise Distribution (OFED) 2.0 stack, supporting a wide range of Infinband protocols including updates to Oracle's Reliable Datagram Sockets (RDS) Numerous driver updates in close coordination with our hardware partners UEK R3 uses the same versioning model as the mainline Linux kernel version. Unlike in UEK R2 (which identifies itself as version "2.6.39", even though it is based on mainline Linux 3.0.x), "uname" returns the actual version number (3.8.13). For further details on the new features, changes and any known issues, please consult the Release Notes. The Unbreakable Enterprise Kernel Release 3 and related packages can be installed using the yum package management tool on Oracle Linux 6 Update 4 or newer, both from the Unbreakable Linux Network (ULN) and our public yum server. Please follow the installation instructions in the Release Notes for a detailed description of the steps involved. The kernel source tree will also available via the git source code revision control system from https://oss.oracle.com/git/?p=linux-uek3-3.8.git If you would like to discuss your experiences with Oracle Linux and UEK R3, we look forward to your feedback on our public Oracle Linux Forum.

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >