Search Results

Search found 729 results on 30 pages for 'obi wan'.

Page 26/30 | < Previous Page | 22 23 24 25 26 27 28 29 30  | Next Page >

  • Routing public IPs (each a /32) through a VPN to another server

    - by Lee S
    Hopefully the title makes sense; I have a server currently in a colo facility, with many IP addresses routed to it. They are individual IPs and not in a contiguous block. Due to vastly improved connectivity (fibre) at home I am slowly bringing my infrastructure in-house for managability and eventually, cost savings. What I would like to do though is use the IP addresses allocated to my existing server, at home. I have an IP block allocated to me on my new ISP connection, but for a couple of reasons I'd like to make use of the colo ones for now: Ease of transition - lots of domains, dns, hard-coded IPs in programs, etc. Connectivity fallback. If my primary line goes down and switches to fallback 1 (dsl) or fallback 2 (4G), I lose access to the ISP-allocated IP block of IPs that are only presented on the primary WAN interface. What I'd like to achieve is my home virtualisation server (Proxmox/Debian-based) "dials in" to the colo server in the colo facility (also Proxmox/Debian) via VPN or similar, and gets to make use of the IP addresses that currently terminate on the colo box. If the primary connection to my ISP goes down and one of the fallback routes kicks in, the VPN tunnel will just time out and then be re-established on the backup connection instead. I'm sure this is doable, but I have no idea how. I'm not afraid to get my hands dirty, I just don't really know where to start?

    Read the article

  • Remote network traffic not passing through VPN

    - by John Virgolino
    We have the following topology: LAN A LAN B LAN C 10.14.0.0/16 <-VPN-> 10.18.0.0/16 --- SONICWALL <-VPN-> M0N0WALL --- 10.32.0.0/16 Traffic between LAN A and LAN B works perfectly. Traffic between LAN C and LAN B works perfectly. Traffic between LAN A and LAN C, not so much. LAN A's gateway has a route to LAN C that points to the Sonicwall. The Sonicwall has a route to LAN A pointing to the VPN gateway connecting LAN B to LAN A. Tracing packets on the Sonicwall shows the LAN C destined traffic to arrive on the Sonicwall, but it does not forward the traffic, it dies there. Traffic from LAN B gets forwarded. Tracing packets on the Sonicwall while sending traffic from LAN C destined for LAN A shows nothing. This tells me that the M0N0WALL is not forwarding traffic for the 10.14.0.0 network and the Sonicwall is not forwarding from 10.14.0.0. The SA on the Sonicwall terminates on the WAN ZONE and is defined to use an address group that incorporates both the 10.14.0.0 and 10.18.0.0 networks. The M0N0WALL is configured for the 10.18.0.0 network and I have tried with both a static route to 10.14.0.0 and without on the M0N0WALL. I tried manually adding the 10.14.0.0 network to the SA on the M0N0WALL, but that really aggravated it and the SA never came up, so I reverted. I have checked all the firewall rules to make sure nothing is blocked. All of the Sonicwall auto-added rules look right. Specs: Sonicwall TZ200, Enhanced OS M0N0WALL v1.32 I'm at a loss at this point. Any help would be appreciated.

    Read the article

  • iptables : how to allow incoming ftp traffic?

    - by logansama
    Hi, Still fighting my way through the jungle that is called iptables. I have managed to allow FTP access outside of our LAN: both these would work. NOTE: eth0 is the LAN interface and eth1 is the WAN interface. iptables -t filter -A FORWARD -i eth0 -p tcp --dport 20:21 -j ACCEPT or iptables -A FORWARD -i eth0 -o eth1 -p tcp --sport 20:21 --dport 1024:65535 -j ACCEPT But when i connect to a external FTP server i manage to log in and all is fine until it wishes to List the directory content. Then nothing happens as the data is blocked, due to the fact that i do not have a rule set up to allow it! (my last rule on the FORWARD chain is to block all traffic) I have tried a gazillion rules (many of which i did not understand) to try and allow the FTP traffic back through my server. One such rule for example was: iptables -A FORWARD -i eth1 -o eth0 -p tcp --sport 20:21 --dport 1024:65535 -j ACCEPT But i cannot get the List to work. It just times out after a while. Would anyone perhaps know how to build a rule which would allow FTP to List / allow such traffic back? Or have a link to sources i could work through? Thank you,

    Read the article

  • hosting company blocking google bots and crawlers [closed]

    - by Jayapal Chandran
    Hi, I am having a site for the past three years and it is very active for the past two years. Until not the site is working well and also now but not after the hosting company blocked google bots. Many pages appeared in the first page of the google search. After they started blocking i couldn't see my links in the first page instead they appeared after 5 pages or they did not appear at all. Will hosting companies be so stupid that they block and dont mention it to their users. They want to protect themselves by making the websites at stake. I display google ads and not this month i got only half for this 10 days. I have made requests to other hosting companies like blue host and monster host that i wan to transfer my domain by making a condition that the will not block google bots which stops the business indirectly. so any kind of help will be helpful. how can i claim what i lost from the hosting company. what other hosting companies consider the users (by informing the events like changing the IP or blocking google bot.) It was really working hard to bring up my site but these people just crashed down my site in a few days. :-(

    Read the article

  • ssh initial prompt hangs for 10 minutes but console login and initial prompt is very responsive - why?

    - by rfreytag
    I have been running an ESXi 4.0 server for months with a couple of WinServer2003 and several Ubuntu Server 10.4 VMs. The performance has been impressive on 6GB i7 Asus P6T hardware. Suddenly, a week ago, ssh logins to the Ubuntu VMs take 10 minutes when connecting over the LAN (over a WAN the connection (pipe) is broken long before that). When logging in to these VMs the password prompt arrives immediately, and failed passwords are responded to immediately. But the moment I log in then the shell prompt appears and I hang for many minutes. Sometimes the connection hangs before the shell prompt appears and sometimes I can type in a command but the moment I hit return the machine hangs. 10 full minute later control returns and the VM is responsive. NOTE: there are several Ubuntu VMs on the same host machine that are identical in all ways that I can tell. However, only one of the VMs displays this behavior. That is why I mention the ESXi host in passing - I don't think it has anything to do with the problem. This behavior is never seen when I connect with the troubled-VM's console (through vSphere Client). From the console the Ubuntu VMs all respond beautifully. I have seen: http://kb.vmware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&externalId=1003496&sliceId=1&docTypeID=DT_KB_1_1&dialogID=229586372&stateId=1%200%20229588522 ...and since that relates to delays in seeing the password prompt that does not appear to be the solution here. Any other suggestions very welcome - thank you.

    Read the article

  • Sending eMails in a external subnet in vmware ESXi

    - by user80658
    This might be a bit hard for me to explain - and it is a pretty individual situation. I got a native server at Hetzner (www.hetzner.de). The public IP is 88.[...].12. I got ESXi running on this server. I can access the esxi console by the public ip, but none of the virtual machines. That's why I bought a public subnet with 8 (6 usable) IPs (46.[...]) and an additional public ip (88.[...].26). This additional public ip belongs to the first virtual maschine - a firewall appliance - which is connected to the WAN. This need to be done this way - since it is the official way by hetzner. My 46. subnet is behind the firewall. I got a virtualmin server with dovecot imap/pop3 server. When sending a email, most provider (gmail) will accept those mails, but a lot will put it into spam (aol). My theory is: The MX line of my domain says of course the ip of the virtual machine (46.[...]), but in the raw email it says that email is sent by the ip of the firewall (88.[...].26), which doesnt sound trustworthy. A solution would be if the firewall could handle mail, but it simply cant. How can I prevent this problem? Thanks.

    Read the article

  • Cisco configuration for public library internet

    - by AlternateZ
    I'm a C/C++ computer programmer turned IT support guy working for a public library. My day is usually spent helping random grandparents learn how to use email, so my networking knowledge is limited to what I can glean from google. Here's the situation. We have a public library with 20 PCs on a LAN and also public wifi access. Previously we were running all of this on 1 ADSL connection and people complained about low speeds. We hired a networking company to set up a Cisco dual-WAN router for us, and purchased an additional ADSL connection. The intention was to give the LAN PCs a guaranteed amount of bandwidth each, and then let the wifi users split the rest. The results were far worse than what we expected, and all we got from the company was excuses and they've since washed their hands of us. During busy periods, net performance on the LAN PCs are so poor that attaching files to gmail etc often times out and fails - far from the "guaranteed amount of bandwidth each" that we hope for! Sometimes it feels like performance is worse than before when we had 1 ADSL link and an unconfigured router? Anyways, surely this is a problem encountered a million times over across the world? (Sharing internet across many users effectively.) What are standard solutions for something like this? I admit to not even knowing the right jargon to google for (load balancing?) I'd appreciate any links to resources/guides that might help me get a better understanding of the problem/solutions, and perhaps some stories of your own experience in solving similar problems. This will help us evaluate and negotiate with network consultants in the future. If its relevant, our router config contains a section "policy-map" with "bandwidth percent" for each class of user (LAN, wifi), and "fair queue".

    Read the article

  • Steps to debugging web site latency and timeout issues

    - by Paperjam
    I have a client who has multiple offices around the country, all of which share the same Internet connection via their WAN. One specific office for this client is experiencing severe latency and timeout issues with my web site. Most, but not all, of the latency occurs on a specific ASPX page where multiple postbacks are made while populating cascading dropdown lists (rapid form submits). The latency is sporadic and can be anywhere from a few seconds to a full timeout. There is no indication that the timeouts are occurring on the server's end. The IT guy for this client is having trouble narrowing down the problem. Since it is affecting only one location for one client, I am led to believe it is not something with my site but something specific to that location. He's measured ping times while using the site and has noticed no real variance in ping times even when the page has timed out. I believe this may be being caused by some sort of Internet filter that doesn't like rapid form submits, but beyond a hunch I haven't a clue. My question is what things should I tell the IT guy to look for? While I'm not trying to provide active tech support for this issue, I would at least like to glean an understanding of what is going on and try to offer some sort of advice. Thank you.

    Read the article

  • Pulling application updates from closest server?

    - by Mike Morris
    Setup: 6 Major Sites with Server 2003/2008 DCs doing DHCP/AD Integrated DNS, each on their own subnet. All connect back to datacenter through a 3 mbps WAN ERP server running in the datacenter, accessed by clients at all sites Currently, when we update the software, I manually push a copy of the updated client/config files down to each DC. I have a script that we run on each PC to update the clients. It determines what subnet the PC is on, and pulls the software from that DC. It's messy, but it works. The client has an autoupdate feature, but it'll only pull from the application server (which is housed in the datacenter, over the 3 meg link). It takes forever, since the updates are not "patches" but a full version of the client, even for minor upgrades (bad design). After the most recent patch, you can configure the clients to pull from a different server. Unfortunately, it is the same for all clients. Is there some kind of DNS magic I can use to pull from the local server? For instance, if I tell the clients their update server is ERPUPDATE, can I have their local DNS server return a different IP for ERPUPDATE than the other sites? Example: Client 1 is at site A, client 2 is at site b. They each run the software and a version change is detected. As per the config files, the clients look to ERPUPDATE for their updated client. Client 1 queries DNS for the IP of ERPUPDATE at its current location (site A) DNS at site A returns 192.1.1.5 Client 1 pulls update from 192.1.1.5 Client 2 queries DNS for the IP of ERPUPDATE at its current location (site B) DNS at site B returns 192.1.2.5 Client 2 pulls update from 192.1.2.5 Excuse the poor explanation, I worked 61 hours over the weekend and haven't completely rebounded. I'll be happy to clarify if needed!

    Read the article

  • Why is this iptables rule that does port forwarding not working?

    - by videoguy
    I have a server bound to localhost:7060. It is using ipv6 socket instead of ipv4. Below is netstat outout. # netstat -an Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 10.200.32.98:1720 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4122 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4123 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:4123 127.0.0.1:43051 ESTABLISHED tcp 0 0 10.200.32.98:5555 10.200.32.44:53162 ESTABLISHED tcp6 0 0 :::5060 :::* LISTEN tcp6 0 0 ::ffff:127.0.0.1:7060 :::* LISTEN tcp6 0 0 :::23 :::* LISTEN tcp6 0 0 ::ffff:10.200.32.98:23 ::ffff:10.200.32.142:43505 ESTABLISHED tcp6 0 0 ::ffff:127.0.0.1:43051 ::ffff:127.0.0.1:4123 ESTABLISHED tcp6 0 0 ::ffff:10.200.32.98:23 ::ffff:10.200.32.44:53195 ESTABLISHED udp6 0 0 :::5060 :::* CLOSE # I want to setup a port forwarding rule that accepts connections on port 24 (on all interfaces loopback as well as eth0) and forward the data to localhost:7060. This is how I am setting up the iptables rule: iptables -t nat -A PREROUTING -p tcp --dport 24 -j DNAT --to 127.0.0.1:7060** It is not working. When I telnet from different box, I see the following $telnet 10.200.32.98 24 Trying 10.200.32.98... If I change the server to bind to *:7060 and set the following rule, it seems to work fine. iptables -t nat -A PREROUTING -p tcp --dport 24 -j REDIRECT --to-port 7060 But that will make my server available on WAN interface which I don't like. I feel it had something to do with ipv6 socket (tcp6 line in netstat output). This whole thing is done on an Android device with custom built Android platform image. How do I get this working?

    Read the article

  • How do I setup a proper VPN for my friends to play LAN games AND give them internet access?

    - by Gizmo
    I'm trying to setup a VPN on my local network, but everyone who connects to me DOES have access to my laptop but not to the internet or other devices on the network. How can I properly configure my VPN on windows to work correctly (giving internet + access to all devices on my network to the remote pc)? Or is there software on windows which makes creating a VPN server easier? or maybe a VMWare image linux vpn server? I can't find any of those! My requirement is that my friends don't have to install additional software, they have to be able to connect with default windows stuff. My OS is Windows 8 Standart edition (not pro or enterprise) OEM. Most of my friends have also windows 8, some windows 7. Extra info: My device is DMZ'ed (Demilitarized Zone, [disabled NAT on my device so it's accessible on the WAN]) I can access files, websites and services on other devices on my network, and all devices can access file shares, website and all other services on my device When enabling VPN everything works except the client is unable to get internet access or access to any device on my network, client has only access to my device.

    Read the article

  • Many clients on a wireless AP for UDP broadcast packets

    - by distorteddisco
    I asked this question on StackOverflow and was directed over here, so I'd appreciate any advice. I'm deploying a smartphone application as part of a live music performance that depends on receiving UDP broadcast packets from a wireless access point. I'm guessing that between 20 and 50 clients will be connected at any one time. I'm aware that a maximum of 20 clients per access point is advised, but as the UDP broadcast packets are ground through the LAN, how would I be able to link multiple APs together? I'm looking for recommendations on a suitable AP for this. The actual data transmission rates are very low - only a few kB/s - as I'm just sending small messages to the smartphone apps, and there will be no WAN internet connection. I tried it with a few connected peers on an adhoc wireless connection without any problems, but ran into dropped packet issues on an old WRT54G running ddwrt, though it's in pretty rough shape. What's the best way to do this? I suppose I could limit concurrent wireless connections to 20 clients... but more would be nice. EDIT: I should also say that it's purely one-way communication; the smartphone application is only receiving broadcast packets, not sending anything.

    Read the article

  • Secure NAT setup with iptables

    - by TheBigB
    I have Debian running device that needs to act as an internet-gateway. On top of that I want to provide a firewall that not only blocks inbound traffic, but also outbound traffic. And I figured iptables should be able to do the job. The problem: I've configured NAT properly (I think?), but once I set the default policy to DROP and add rules to for instance allow HTTP traffic from inside the LAN, HTTP is not going through. So basically my rules don't seem to work. Below is the initialization script that I use for iptables. The device has two NICs, respectively eth0 (the WAN interface) and eth1 (the LAN interface). echo 1 > /proc/sys/net/ipv4/ip_forward # Flush tables iptables -F iptables -t nat -F # Set policies iptables -P INPUT DROP iptables -P OUTPUT DROP # NAT iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT # Allow outbound HTTP from LAN? iptables -A FORWARD -i eth1 -o eth0 -p tcp --dport 80 -j ACCEPT iptables -A OUTPUT -p tcp --dport 80 -j ACCEPT Can anyone shed some light on this?

    Read the article

  • Why does my router log crazy amounts of blocked traffic on port 1701?

    - by Vlad Seghete
    I have a 2701HGV-B 2Wire modem and router (AT&T). The log is basically full with entries similar to the following with a time between a fifth and a third of a second between entries: src=86.156.7.170 dst=xxx.xxx.xxx.38 ipprot=17 sport=6882 dport=1701 Unknown inbound session stopped src=58.176.22.252 dst=xxx.xxx.xxx.38 ipprot=17 sport=21573 dport=1701 Unknown inbound session stopped src=91.221.6.250 dst=xxx.xxx.xxx.38 ipprot=17 sport=25902 dport=1701 Unknown inbound session stopped ... where the source IP will be different for every entry. The entries accumulate constantly, every single second that the router is on several of them appear in the log. The destination is the WAN address for my router. I understand that this is somehow related to VNCs, but I don't know enough to figure out why my router is getting bombarded with requests for a VNC session. Is there anything fishy going on or is this normal? If it is normal, how do I keep these entries from spamming my log files? Since there's about two or three of them every second, everything else gets drowned out.

    Read the article

  • Can't Ping - Wireless network of home

    - by Naunidh
    Hello, This may seem like other ping problem, but I have tried a lot before posting it here. I have a linksys WRT54G - firmware v8.00.8. I have two laptops one windows vista (192.168.1.99) and Windows Xp (192.168.1.13) connected on WiFi . The Router's IP address is 192.168.1.4, and default gateway is the ADSL modem (192.168.1.1) connected through wire. The problem is that laptops can not ping each other, they can ping the gateway and the linksys router, and both can access internet. Following has been tried (I am pinging from XP machine to Vista): I saw that arp entires for Vista machines were not being populated, so I added static ARP entries. 192.168.1.99 00-19-7e-70-d0-4e static I checked on ethereal that an ICMP packet for MAC address of Vista machine does go out from XP machine towards the Vista machine, but never reaches the Vista machine. So its get eaten by the Router? I added Vista machine to DMZ in my linksys router, so that all the ports are open (In case it was an issue). Firewalls , antivirus etc were turned off, echo was enabled explicitly on vista, file sharing, network discovery were turned on. Network type was set to private. Unchecked everything in Router;s firewall, even though they are only meant for WAN requests. Is there anything else that I should try. Thanks.

    Read the article

  • setting up vpn server

    - by Lock
    I need help in visualising how to setup our VPN box when we move to our new network with Telstra. We have a safe@office 500P, which has a public IP and a private IP of 192.168.19.2. It is physically connected to our router, which has 4 different interfaces, one being 192.168.19.1. On the VPN box, we have a static route to forward everything to 192.168.19.1 which is the router, and from there it works out where to go. Now, we are moving to a Telstra WAN and things are setup a little differently. Our head office router has only 3 interfaces- 1 is for the link to the switch that has the fibre connection (so our route to the internet and other branches), 1 is for our 10.10.20.x network and one is for the local branch network. I really have no idea how to set this up as with the new setup, we will not have a port for it to plug into on the router. Could I just plug it into the 10.10.20.x network? Would I have to give it a public IP or can we just forward through the ports that it would use? Another suggestion was to VLAN our switch into two networks- one for the 10.10.20.x network and one for the network the VPN currently sits on (192.168.19.x), and setup the router to trunk between the port and the switch. Not sure how to do this. Sorry VPN's are definitely not my strong suit. Any advice appreciated!

    Read the article

  • Route all traffic of home network through VPN [migrated]

    - by user436118
    I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

    Read the article

  • Iptables state tracking

    - by complexgeek
    Hi there. I've just taken over administration of a fairly complex firewall ruleset for a firewall box running Fedora Core 12, and there's one thing about it that is puzzling me. When I run nmap on the gateway from outside the network, I see all the expected services, but also sunrpc on port 111. The INPUT chain has DEFAULT DROP set, and there is no rule allowing port 111. As best I can tell (watching the packet counters before/during/after the scan) it's being allowed by the rule: "-m state --state RELATED,ESTABLISHED -j ACCEPT" but I don't understand why a brand new TCP connection would be considered RELATED or ESTABLISHED. Any suggestions would be greatly appreciated. EDIT: Conntrack modules: nf_conntrack_netlink 14925 0 nfnetlink 3479 1 nf_conntrack_netlink nf_conntrack_irc 5206 1 nf_nat_irc nf_conntrack_proto_udplite 3138 0 nf_conntrack_h323 62110 1 nf_nat_h323 nf_conntrack_proto_dccp 6878 0 nf_conntrack_sip 16921 1 nf_nat_sip nf_conntrack_proto_sctp 11131 0 nf_conntrack_pptp 10673 1 nf_nat_pptp nf_conntrack_sane 5458 0 nf_conntrack_proto_gre 6574 1 nf_conntrack_pptp nf_conntrack_amanda 2796 1 nf_nat_amanda nf_conntrack_ftp 11741 1 nf_nat_ftp nf_conntrack_tftp 4665 1 nf_nat_tftp nf_conntrack_netbios_ns 1534 0 nf_conntrack_ipv6 18504 2 ipv6 279399 40 ip6t_REJECT,nf_conntrack_ipv6 INPUT chain on the filter table: -A INPUT -s 192.168.200.10/32 -p tcp -m tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT -A INPUT -s 127.0.0.0/8 -i lo -j ACCEPT -A INPUT -p udp -m udp --sport 67:68 --dport 67:68 -j ACCEPT -A INPUT -d 192.168.200.5/32 -i eth0 -j ACCEPT -A INPUT -d 192.168.1.2/32 -i eth0 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p tcp -m multiport --dports 22,80,443 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p tcp -m multiport --sports 22,25,80,443 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p udp -m udp --dport 1194 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p udp -m udp --sport 1194 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p udp -m multiport --sports 53,123 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p icmp -m icmp --icmp-type 8 -j ACCEPT -A INPUT -i eth0 -m state --state NEW -j ACCEPT -A INPUT -d {public_ip}/32 -m state --state NEW -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT eth0 is connected to the internal network, eth3 is connected to an ADSL modem in bridge mode, ppp0 is the WAN connection tunneled over eth3.

    Read the article

  • What is SharePoint Out of the Box?

    - by Bil Simser
    It’s always fun in the blog-o-sphere and SharePoint bloggers always keep the pot boiling. Bjorn Furuknap recently posted a blog entry titled Why Out-of-the-Box Makes No Sense in SharePoint, quickly followed up by a rebuttal by Marc Anderson on his blog. Okay, now that we have all the players and the stage what’s the big deal? Bjorn started his post saying that you don’t use “out-of-the-box” (OOTB) SharePoint because it makes no sense. I have to disagree with his premise because what he calls OOTB is basically installing SharePoint and admiring it, but not using it. In his post he lays claim that modifying say the OOTB contacts list by removing (or I suppose adding) a column, now puts you in a situation where you’re no longer using the OOTB functionality. Really? Side note. Dear Internet, please stop comparing building software to building houses. Or comparing software architecture to building architecture. Or comparing web sites to making dinner. Are you trying to dumb down something so the general masses understand it? Comparing a technical skill to a construction operation isn’t the way to do this. Last time I checked, most people don’t know how to build houses and last time I checked people reading technical SharePoint blogs are generally technical people that understand the terms you use. Putting metaphors around software development to make it easy to understand is detrimental to the goal. </rant> Okay, where were we? Right, adding columns to lists means you are no longer using the OOTB functionality. Yeah, I still don’t get it. Another statement Bjorn makes is that using the OOTB functionality kills the flexibility SharePoint has in creating exactly what you want. IMHO this really flies in the absolute face of *where* SharePoint *really* shines. For the past year or so I’ve been leaning more and more towards OOTB solutions over custom development for the simple reason that its expensive to maintain systems and code and assets. SharePoint has enabled me to do this simply by providing the tools where I can give users what they need without cracking open up Visual Studio. This might be the fact that my day job is with a regulated company and there’s more scrutiny with spending money on anything new, but frankly that should be the position of any responsible developer, architect, manager, or PM. Do you really want to throw money away because some developer tells you that you need a custom web part when perhaps with some creative thinking or expectation setting with customers you can meet the need with what you already have. The way I read Bjorn’s terminology of “out-of-the-box” is install the software and tell people to go to a website and admire the OOTB system, but don’t change it! For those that know things like WordPress, DotNetNuke, SubText, Drupal or any of those content management/blogging systems, its akin to installing the software and setting up the “Hello World” blog post or page, then staring at it like it’s useful. “Yes, we are using WordPress!”. Then not adding a new post, creating a new category, or adding an About page. Perhaps I’m wrong in my interpretation. This leads us to what is OOTB SharePoint? To many people I’ve talked to the last few hours on twitter, email, etc. it is *not* just installing software but actually using it as it was fit for purpose. What’s the purpose of SharePoint then? It has many purposes, but using the OOTB templates Microsoft has given you the ability to collaborate on projects, author/share/publish documents, create pages, track items/contacts/tasks/etc. in a multi-user web based interface, and so on. Microsoft has pretty clear definitions of these different levels of SharePoint we’re talking about and I think it’s important for everyone to know what they are and what they mean. Personalization and Administration To me, this is the OOTB experience. You install the product and then are able to do things like create new lists, sites, edit and personalize pages, create new views, etc. Basically use the platform services available to you with Windows SharePoint Services (or SharePoint Foundation in 2010) to your full advantage. No code, no special tools needed, and very little user training required. Could you take someone who has never done anything in a website or piece of software and unleash them onto a site? Probably not. However I would argue that anyone who’s configured the Outlook reading layout or applied styles to a Word document probably won’t have too much difficulty in using SharePoint OUT OF THE BOX. Customization Here’s where things might get a bit murky but to me this is where you start looking at HTML/ASPX page code through SharePoint Designer, using jQuery scripts and plugging them into Web Part Pages via a Content Editor Web Part, and generally enhancing the site. The JavaScript debate might kick in here claiming it’s no different than C#, and frankly you can totally screw a site up with jQuery on a CEWP just as easily as you can with a C# delegate control deployed to the server file system. However (again, my blog, my opinion) the customization label comes in when I need to access the server (for example creating a custom theme) or have some kind of net-new element I add to the system that wasn’t there OOTB. It’s not content (like a new list or site), it’s code and does something functional. Development Here’s were the propeller hats come on and we’re talking algorithms and unit tests and compilers oh my. Software is deployed to the server, people are writing solutions after some kind of training (perhaps), there might be some specialized tools they use to craft and deploy the solutions, there’s the possibility of exceptions being thrown, etc. There are a lot of definitions here and just like customization it might get murky (do you let non-developers build solutions using development, i.e. jQuery/C#?). In my experience, it’s much more cost effective keeping solutions under the first two umbrellas than leaping into the third one. Arguably you could say that you can’t build useful solutions without *some* kind of code (even just some simple jQuery). I think you can get a *lot* of value just from using the OOTB experience and I don’t think you’re constraining your users that much. I’m not saying Marc or Bjorn are wrong. Like Obi-Wan stated, they’re both correct “from a certain point of view”. To me, SharePoint Out of the Box makes total sense and should not be dismissed. I just don’t agree with the premise that Bjorn is basing his statements on but that’s just my opinion and his is different and never the twain shall meet.

    Read the article

  • krb5-multidev, libk5crypto3, libk5crypto3:i386 package dependency

    - by TDalton
    Using Ubuntu 12.04 Asus U43F I can no longer update, install or remove packages via software center because of package dependency errors. sudo apt-get install -f reads the following: Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages were automatically installed and are no longer required: libunity6 libqapt-runtime libboost-program-options1.46.1 akonadi-backend-mysql libqapt1 shared-desktop-ontologies libntrack0 ntrack-module-libnl-0 libntrack-qt4-1 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: krb5-multidev libk5crypto3:i386 libkrb5-dev Suggested packages: krb5-doc krb5-doc:i386 krb5-user:i386 The following packages will be upgraded: krb5-multidev libk5crypto3:i386 libkrb5-dev 3 upgraded, 0 newly installed, 0 to remove and 325 not upgraded. 11 not fully installed or removed. Need to get 0 B/213 kB of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y dpkg: error processing libk5crypto3 (--configure): libk5crypto3:amd64 1.10+dfsg~beta1-2ubuntu0.3 cannot be configured because libk5crypto3:i386 is in a different version (1.10+dfsg~beta1-2ubuntu0.1) dpkg: error processing libk5crypto3:i386 (--configure): libk5crypto3:i386 1.10+dfsg~beta1-2ubuntu0.1 cannot be configured because libk5crypto3:amd64 is in a different version (1.10+dfsg~beta1-2ubuntu0.3) dpkg: dependency problems prevent configuration of libkrb5-3: libkrb5-3 depends on libk5crypto3 (>= 1.9+dfsg~beta1); however:No apport report written because MaxReports is reached already Package libk5crypto3 is not configured yet. dpkg: error processing libkrb5-3 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libgssapi-krb5-2: libgssapi-krb5-2 depends on libk5crypto3 (>= 1.8+dfsg); however: Package libk5crypto3 is not configured yet. libgssapi-krb5-2 depends on libkrb5-3 (= 1.10+dfsg~beta1-2ubuntu0.3); however: Package libkrb5-3 is not configured yet. dpkg: error processing libgssapi-krb5-2 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libgssrpc4: libgssrpc4 depends on libgssapi-krb5-2 (>= 1.10+dfsg~); however: Package libgssapi-krb5-2 is not configured yet. dpkg: error processing libgssrpc4 (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of libkadm5srv-mit8: libkadm5srv-mit8 depends on libgssapi-krb5-2 (>= 1.6.dfsg.2); however: Package libgssapi-krb5-2 is not configured yet. libkadm5srv-mit8 depends on libgssrpc4 (>= 1.6.dfsg.2); however: Package libgssrpc4 is not configured yet. libkadm5srv-mit8 depends on libk5crypto3 (>= 1.6.dfsg.2); however: Package libk5crypto3 is not configured yet. libkadm5srv-mit8 depends on libkrb5-3 (>= 1.9+dfsg~beta1); however: Package libkrb5-3 is not configured yet. dpkg: error processing libkadm5srv-mit8 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libkadm5clnt-mit8: libkadm5clnt-mit8 depends on libgssapi-krb5-2 (>= 1.10+dfsg~); however: Package libgssapi-krb5-2 is not configured yet. libkadm5clnt-mit8 depends on libgssrpc4 (>= 1.6.dfsg.2); however: Package libgssrpc4 is not configured yet.No apport report written because MaxReports is reached already libkadm5clnt-mit8 depends on libk5crypto3 (>= 1.6.dfsg.2); however: Package libk5crypto3 is not configured yet. libkadm5clnt-mit8 depends on libkrb5-3 (>= 1.8+dfsg); however: Package libkrb5-3 is not configured yet. dpkg: error processing libkadm5clnt-mit8 (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of krb5-multidev: krb5-multidev depends on libkrb5-3 (= 1.10+dfsg~beta1-2ubuntu0.2); however: Version of libkrb5-3 on system is 1.10+dfsg~beta1-2ubuntu0.3. krb5-multidev depends on libk5crypto3 (= 1.10+dfsg~beta1-2ubuntu0.2); however: Version of libk5crypto3 on system is 1.10+dfsg~beta1-2ubuntu0.3. krb5-multidev depends on libgssapi-krb5-2 (= 1.10+dfsg~beta1-2ubuntu0.2); however: Version of libgssapi-krb5-2 on system is 1.10+dfsg~beta1-2ubuntu0.3. krb5-multidev depends on libgssrpc4 (= 1.10+dfsg~beta1-2ubuntu0.2); however: Version of libgssrpc4 on system is 1.10+dfsg~beta1-2ubuntu0.3. krb5-multidev depends on libkadm5srv-mit8 (= 1.10+dfsg~beta1-2ubuntu0.2); however: Version of libkadm5srv-mit8 on system is 1.10+dfsg~beta1-2ubuntu0.3. krb5-multidev depends on libkadm5clnt-mit8 (= 1.10+dfsg~beta1-2ubuntu0.2); however: Version of libkadm5clnt-mit8 on system is 1.10+dfsg~beta1-2ubuntu0.3. dpkg: error processing krb5-multidev (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of libkrb5-dev: libkrb5-dev depends on krb5-multidev (= 1.10+dfsg~beta1-2ubuntu0.2); however: Package krb5-multidev is not configured yet. dpkg: error processing libkrb5-dev (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of libkrb5-3:i386: libkrb5-3:i386 depends on libk5crypto3 (>= 1.9+dfsg~beta1); however: Package libk5crypto3:i386 is not configured yet. dpkg: error processing libkrb5-3:i386 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libgssapi-krb5-2:i386: libgssapi-krb5-2:i386 depends on libk5crypto3 (>= 1.8+dfsg); however: Package libk5crypto3:i386 is not configured yet. libgssapi-krb5-2:i386 depends on libkrb5-3 (= 1.10+dfsg~beta1-2ubuntu0.3); however: Package libkrb5-3:i386 is not configured yet. dpkg: error processing libgssapi-krb5-2:i386 (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: libk5crypto3 libk5crypto3:i386 libkrb5-3 libgssapi-krb5-2 libgssrpc4 libkadm5srv-mit8 libkadm5clnt-mit8 krb5-multidev libkrb5-dev libkrb5-3:i386 libgssapi-krb5-2:i386 E: Sub-process /usr/bin/dpkg returned an error code (1) I have tried to fix the broken dependencies via synaptic package manager, but it returns with an error: E: libk5crypto3: libk5crypto3:amd64 1.10+dfsg~beta1-2ubuntu0.3 cannot be configured because libk5crypto3 E: libkrb5-3: dependency problems - leaving unconfigured E: libgssapi-krb5-2: dependency problems - leaving unconfigured E: libgssrpc4: dependency problems - leaving unconfigured E: libkadm5srv-mit8: dependency problems - leaving unconfigured E: libkadm5clnt-mit8: dependency problems - leaving unconfigured E: krb5-multidev: dependency problems - leaving unconfigured E: libkrb5-dev: dependency problems - leaving unconfigured I haven't gotten help from ubuntuforums.org on this issue. Please help, obi-wan

    Read the article

  • Optimal Serialization of Primitive Types

    - by Greg Dean
    We are beginning to roll out more and more WAN deployments of our product (.Net fat client w/ IIS hosted Remoting backend). Because of this we are trying to reduce the size of the data on the wire. We have overridden the default serialization by implementing ISerializable (similar to this), we are seeing anywhere from 12% to 50% gains. Most of our efforts focus on optimizing arrays of primitive types. I would like to know if anyone knows of any fancy way of serializing primitive types, beyond the obvious? For example today we serialize an array of ints as follows: [4-bytes (array length)][4-bytes][4-bytes] Can anyone do significantly better? The most obvious example of a significant improvement, for boolean arrays, is putting 8 bools in each byte, which we already do. Note: Saving 7 bits per bool may seem like a waste of time, but when you are dealing with large magnitudes of data (which we are), it adds up very fast. Note: We want to avoid general compression algorithms because of the latency associated with it. Remoting only supports buffered requests/responses(no chunked encoding). I realize there is a fine line between compression and optimal serialization, but our tests indicate we can afford very specific serialization optimizations at very little cost in latency. Whereas reprocessing the entire buffered response into new compressed buffer is too expensive.

    Read the article

  • create graph using adjacency list

    - by sum1needhelp
    #include<iostream> using namespace std; class TCSGraph{ public: void addVertex(int vertex); void display(); TCSGraph(){ head = NULL; } ~TCSGraph(); private: struct ListNode { string name; struct ListNode *next; }; ListNode *head; } void TCSGraph::addVertex(int vertex){ ListNode *newNode; ListNode *nodePtr; string vName; for(int i = 0; i < vertex ; i++ ){ cout << "what is the name of the vertex"<< endl; cin >> vName; newNode = new ListNode; newNode->name = vName; if (!head) head = newNode; else nodePtr = head; while(nodePtr->next) nodePtr = nodePtr->next; nodePtr->next = newNode; } } void TCSGraph::display(){ ListNode *nodePtr; nodePtr = head; while(nodePtr){ cout << nodePtr->name<< endl; nodePtr = nodePtr->next; } } int main(){ int vertex; cout << " how many vertex u wan to add" << endl; cin >> vertex; TCSGraph g; g.addVertex(vertex); g.display(); return 0; }

    Read the article

  • iPhone sdk Cocoa Touch - Pass touches down from parent UIView to child UIScrollview

    - by Joe
    I have a UIView inside my xib in IB and inside that is a UIScrollview that is a small 80x80 square and dynamically loaded with 8 or so 80 x 80 thumbnail images. The UIScrollview is not clipping the images so that they extend out either side so you can swipe left and right to scroll a chosen image into the the centre, paging is on so they snap ti each image. I have researched and found this is the best and possibly only way to do this. The UIScrollview sits in a 'container' UIView for one reason, it is there to receive the touches/swipes and pass them down to it's child the UIScrollview as otherwise all touches would have to start in the small 80x80 UIScrollview area and I wan them to be anywhere along the row of images. I have seen some sample code somewhere for doing this but just can not implement it. Treat me as a noob, starting from beginning to end, how should the UIView and UIScrollview be set up in IB to allow any touches to be passed, and what code should I put into where? The UIView is set up as scroll_container and the child UIScrollview is char_scroll At the moment I have got it all working except for the touches being passed from the parent to the child, and at the moment the touches have to always start inside the UIScrollview (tiny 80x80 box in centre) when I want to be able to swipe left or right in the long 480X80 horizontal parent UIView and have this still scroll the child UIScrollview. Hope you can help and understand what I mean!

    Read the article

  • Telerik Silverlight RadComboBox Selected Item

    - by Chirag
    i am customize telerik Datapager control in that control create one resource file and add one combobox for change page size of grid <UserControl.Resources> ....... <telerik:RadComboBox x:Name="CmbPageSize" MinWidth="40" telerik:StyleManager.Theme="{StaticResource Theme}" ItemsSource="{Binding Path=BindPageSize, Mode=TwoWay}" SelectedItem="{Binding Path=DataPagerPageSize_string, Mode=TwoWay}"></telerik:RadComboBox> ....... Bind a combo with public string DataPagerPageSize_string { get { if (_DataPagerPageSize_string == null || _DataPagerPageSize_string == string.Empty) { //DatapagerIndex = 1; return DefaultPageSize.ToString(); } return _DataPagerPageSize_string; } set { _DataPagerPageSize_string = value; OnPropertyChanged("_DataPagerPageSize_string"); } } public List<string> BindPageSize { get { List<string> Pagerdata = new List<string>(); Pagerdata.Add("10"); Pagerdata.Add("20"); Pagerdata.Add("50"); Pagerdata.Add("100"); Pagerdata.Add("250"); Pagerdata.Add("500"); Pagerdata.Add("750"); Pagerdata.Add("1000"); Pagerdata.Add("1500"); Pagerdata.Add("2000"); Pagerdata.Add("Automatic"); Pagerdata.Add("All"); return Pagerdata; } } this is working fine in case of if i select a value from combobox but i wan to change it from code behind Like EVP.DataPagerPageSize_string = "All"; this thigs works fine but Combobox display me a old value; if i will check a property then it show me a newly set value but combobox not select newly value

    Read the article

  • XML Comparison?

    - by CrazyNick
    I got a books.xml file from http://msdn.microsoft.com/en-us/library/ms762271(VS.85).aspx and just saved it with two different names, removed few lines from the second file and tried to compare the files using the below powershell code: clear-host $xml = New-Object XML $xml = [xml](Get-Content D:\SharePoint\Powershell\Comparator\Comparator_Config.xml) $xml.config.compare | ForEach-Object { $strFile1 = get-Content $.source; $strFile2 = get-Content $.destination; $diff  = Compare-Object $strFile1 $strFile2; $result1 = $diff | where {$.SideIndicator -eq "<=" } | select InputObject; $result2 = $diff | where {$.SideIndicator -eq "=" } | select InputObject; Write-host "nEntries are differ in First web.config filen"; $result1 | ForEach-Object {write-host $.InputObject}; Write-host "nEntries are differ in Second web.config filen" ;$result2 | ForEach-Object {write-host $.InputObject}; $.parameters | ForEach-Object { write-host $.parameter } } and it is working perfectly and giving me the below results: Entries are differ in First web.config file < price36.95< /price < descriptionMicrosoft Visual Studio 7 is explored in depth, looking at how Visual Basic, Visual C++, C#, and ASP+ are integrated into a comprehensive development environment.< /description Entries are differ in Second web.config file < price< /price < description< /description however I wan to know the root node of the above mentioned nodes, is that possible to find? if so, how?

    Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30  | Next Page >