Search Results

Search found 34699 results on 1388 pages for 'big show 2011'.

Page 261/1388 | < Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >

• Remotely Schedule and Stream Recorded TV in Windows 7 Media Center

  - by DigitalGeekery

  Have you ever been away from home and suddenly realized you forgot to record your favorite program? Now Windows 7 Media Center, users can schedule recordings remotely from their phones or mobile devices with Remote Potato. How it Works Remote Potato installs server software on the host computer running Windows 7 Media Center. Once the software is installed, we’ll need to do some port forwarding on the router and setup an optional dynamic DNS address. When setup is completed, we will access the application through a web based interface. Silverlight is required for Streaming recorded TV, but scheduling recordings can be done through an HTML interface. Installing Remote Potato Download and install Remote Potato on the Media Center PC. (See download link below) If you plan to stream any Recorded TV, you’ll also want to install the streaming pack located on the same page. It isn’t required to stream all shows, only shows that require the AC3 audio codec. Click Yes to allow Remote Potato to add rules to the Windows Firewall for remote access. You’ll likely need to accept a few UAC prompts. When notified that the rules were added, click OK. Remote Potato will then prompt you to allow administrator privileges to reserve a URL for it’s web server. Click Yes. Remote Potato server will start. Click on the configuration button at the right to to reveal the settings tabs.   One the General tab, you’ll have the option to run Remote Potato on startup and minimized in the System Tray. If you’re running Media Center on a dedicated HTPC, you’ll probably want to enable both startup options. Forwarding Ports on Your Router You’ll need to forward a couple ports on your router. By default, these will be ports 9080 and 9081. In this example we’re using a Linksys WRT54GL router, however, the steps for port forwarding will vary from router to router. On the Linksys configuration page, click on the Applications & Gaming Tab, and then the Port Range Forward tab. Under Application, type in a name of your choosing. In both the Start and End boxes, type the port number 9080. Enter the local IP address of your Media Center computer in the IP address column. Click the check box under Enable. Repeat the process on the next line, but this time use port 9081. When finished, click the Save Settings button. Note: It’s highly recommended that you configure the home computer running Media Center & Remote Potato with a static IP address.   Find your IP Address You’ll need to find the IP address assigned to your router from your ISP. There are many ways to do this but a quick and easy way is to visit a site like checkip.dyndns.org (link available below) The current external IP address of your router will be displayed in the browser.   Dynamic DNS This is an optional step, but  it’s highly recommended. Many routers, such as the Linksys WRT54GL we are using, support Dynamic DNS (DDNS). What Dynamic DNS allows you to do is affiliate your home router’s external IP address to a domain name. Every time your home router is assigned a a new IP address by your ISP, the domain name is updated to point to your new IP address. Remote Potato’s user interface is accessed over the Internet is by connecting to your router’s IP address followed by a colon and the port number. (Ex: XXX.XXX.XXX.XXX:9080) Instead of constantly having to look up and remember an IP address, you can use DDNS along with a 3rd party provider like DynDNS.com, to sign up for a free domain name and configure it to be updated each time your router is assigned a new IP address. Go to the DynDNS.com website (See link at the end of the article) and sign up for a free Domain name. You’ll need to register and confirm by email.   Once you’ve signed in and selected your domain name click Activate Services. You’ll get a confirmation message that your domain name has been activated.    On the Linksys WRT54GL click on the Setup tab an then DDNS. Select DynDNS.org, or TZO.com if you prefer to use their service, from the drop down list.   With DynDNS, you’ll need to fill in your username and password you signed up with at the DynDNS website and the hostname you chose. Note: You can connect over your local network with the IP Address of the computer running Remote Potato followed by a colon and the port number. Ex: 192.168.1.2:9080 Logging in Remote Potato and Recording a Show Once you connect, you’ll see the start page. To view the TV listings, click on TV Guide. You’ll then see your guide listings. There are a few ways to navigate the listings. At the top left, you can click on any of the preset time buttons to jump to  the listings at that time of the day.  Click on the arrows to the right and left of the day and date at the top center to proceed to the previous or next day. Or, jump to a specific day with the date and date buttons at the top right.   To setup a recording, click on a program.   You can choose to record the individual show or the entire series by clicking on Record Show or Record Series.   Remote Potato on Mobile Devices Perhaps the coolest feature of Remote Potato is the ability to schedule recording from your phone or mobile device. Note: For any devices or computers without Silverlight, you will be prompted to view the HTML page. Select Browse Listings. Select your program to record. In the Program Details, select Record Show to record the single episode or Record Series to record all instances of the series. You will then see a red dot on the program listing to indicate that the show is scheduled for recording.   Streaming Recorded TV Click on Recorded TV from the home screen to access your previously recorded TV programs. Click on the selection you wish to stream. Click on Play. If you receive this error message, you’ll need to install the streaming pack for Remote Potato. This is found on the same download page as installation files. (See link below) The Begin from slider allows you to start playback from the start (by default) or a different time of the program by moving the slider. The Quality (bitrate) setting  allows you to choose the quality of the playback. We found the video quality on the Normal setting to be pretty lousy, and Low was just pointless. High was the best overall viewing experience as it provided smooth quality video playback. We experienced significant stuttering during playback using the Ultra High setting.   Click Start when you are ready to begin. When playback begins you’ll see a slider at the top right.   Move the slider left or right to increase or decrease the size of the video. There’s also a button to switch to full screen.   Media Center users who travel frequently or are always on the go will likely find Remote Potato to be a blessing. Since being released earlier this year, updates for Remote Potato have come fast and furious. The latest beta release includes support for streaming music and photos. If you like those nice network TV logos, check out our article on adding TV channel logos to Windows Media Center. Downloads and Links Download Remote Potato and Streaming Pack Find your IP address Sign Up for a Domain Name at DynDNS.com Similar Articles Productive Geek Tips Schedule Updates for Windows Media CenterUsing Netflix Watchnow in Windows Vista Media Center (Gmedia)Add a Sleep Timer to Windows 7 Media CenterStartup Customizations for Media Center in Windows 7Enable Media Streaming in Windows Home Server to Windows Media Player TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 FoxClocks adds World Times in your Statusbar (Firefox) Have Fun Editing Photo Editing with Citrify Outlook Connector Upgrade Error Gadfly is a cool Twitter/Silverlight app Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos

  Read the article

• SQL SERVER – World Shapefile Download and Upload to Database – Spatial Database

  - by pinaldave

  During my recent, training I was asked by a student if I know a place where he can download spatial files for all the countries around the world, as well as if there is a way to upload shape files to a database. Here is a quick tutorial for it. VDS Technologies has all the spatial files for every location for free. You can download the spatial file from here. If you cannot find the spatial file you are looking for, please leave a comment here, and I will send you the necessary details. Unzip the file to a folder and it will have the following content. Then, download Shape2SQL tool from SharpGIS. This is one of the best tools available to convert shapefiles to SQL tables. Afterwards, run the .exe file. When the file is run for the first time, it will ask for the database properties. Provide your database details. Select the appropriate shape files and the tool will fill up the essential details automatically. If you do not want to create the index on the column, uncheck the box beside it. The screenshot below is simply explains the procedure. You also have to be careful regarding your data, whether that is GEOMETRY or GEOGRAPHY. In this example,  it is GEOMETRY data. Click “Upload to Database”. It will show you the uploading process. Once the shape file is uploaded, close the application and open SQL Server Management Studio (SSMS). Run the following code in SSMS Query Editor. USE Spatial GO SELECT * FROM dbo.world GO This will show the complete map of world after you click on Spatial Results in Spatial Tab. In Spatial Results Set, the Zoom feature is available. From the Select label column, choose the country name in order to show the country name overlaying the country borders. Let me know if this tutorial is helpful enough. I am planning to write a few more posts about this later. Note: Please note that the images displayed here do not reflect the original political boundaries. These data are pretty old and can probably draw incorrect maps as well. I have personally spotted several parts of the map where some countries are located a little bit inaccurately. Reference : Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, SQL, SQL Add-On, SQL Authority, SQL Query, SQL Scripts, SQL Server, SQL Spatial, SQL Tips and Tricks, SQL Utility, T SQL, Technology

  Read the article

• VS 2010 SP1 and SQL CE

  - by ScottGu

  Last month we released the Beta of VS 2010 Service Pack 1 (SP1).  You can learn more about the VS 2010 SP1 Beta from Jason Zander’s two blog posts about it, and from Scott Hanselman’s blog post that covers some of the new capabilities enabled with it.   You can download and install the VS 2010 SP1 Beta here. Last week I blogged about the new Visual Studio support for IIS Express that we are adding with VS 2010 SP1. In today’s post I’m going to talk about the new VS 2010 SP1 tooling support for SQL CE, and walkthrough some of the cool scenarios it enables.  SQL CE – What is it and why should you care? SQL CE is a free, embedded, database engine that enables easy database storage. No Database Installation Required SQL CE does not require you to run a setup or install a database server in order to use it.  You can simply copy the SQL CE binaries into the \bin directory of your ASP.NET application, and then your web application can use it as a database engine.  No setup or extra security permissions are required for it to run. You do not need to have an administrator account on the machine. Just copy your web application onto any server and it will work. This is true even of medium-trust applications running in a web hosting environment. SQL CE runs in-memory within your ASP.NET application and will start-up when you first access a SQL CE database, and will automatically shutdown when your application is unloaded.  SQL CE databases are stored as files that live within the \App_Data folder of your ASP.NET Applications. Works with Existing Data APIs SQL CE 4 works with existing .NET-based data APIs, and supports a SQL Server compatible query syntax.  This means you can use existing data APIs like ADO.NET, as well as use higher-level ORMs like Entity Framework and NHibernate with SQL CE.  This enables you to use the same data programming skills and data APIs you know today. Supports Development, Testing and Production Scenarios SQL CE can be used for development scenarios, testing scenarios, and light production usage scenarios.  With the SQL CE 4 release we’ve done the engineering work to ensure that SQL CE won’t crash or deadlock when used in a multi-threaded server scenario (like ASP.NET).  This is a big change from previous releases of SQL CE – which were designed for client-only scenarios and which explicitly blocked running in web-server environments.  Starting with SQL CE 4 you can use it in a web-server as well. There are no license restrictions with SQL CE.  It is also totally free. Easy Migration to SQL Server SQL CE is an embedded database – which makes it ideal for development, testing, and light-usage scenarios.  For high-volume sites and applications you’ll probably want to migrate your database to use SQL Server Express (which is free), SQL Server or SQL Azure.  These servers enable much better scalability, more development features (including features like Stored Procedures – which aren’t supported with SQL CE), as well as more advanced data management capabilities. We’ll ship migration tools that enable you to optionally take SQL CE databases and easily upgrade them to use SQL Server Express, SQL Server, or SQL Azure.  You will not need to change your code when upgrading a SQL CE database to SQL Server or SQL Azure.  Our goal is to enable you to be able to simply change the database connection string in your web.config file and have your application just work. New Tooling Support for SQL CE in VS 2010 SP1 VS 2010 SP1 includes much improved tooling support for SQL CE, and adds support for using SQL CE within ASP.NET projects for the first time.  With VS 2010 SP1 you can now: Create new SQL CE Databases Edit and Modify SQL CE Database Schema and Indexes Populate SQL CE Databases within Data Use the Entity Framework (EF) designer to create model layers against SQL CE databases Use EF Code First to define model layers in code, then create a SQL CE database from them, and optionally edit the DB with VS Deploy SQL CE databases to remote servers using Web Deploy and optionally convert them to full SQL Server databases You can take advantage of all of the above features from within both ASP.NET Web Forms and ASP.NET MVC based projects. Download You can enable SQL CE tooling support within VS 2010 by first installing VS 2010 SP1 (beta). Once SP1 is installed, you’ll also then need to install the SQL CE Tools for Visual Studio download.  This is a separate download that enables the SQL CE tooling support for VS 2010 SP1. Walkthrough of Two Scenarios In this blog post I’m going to walkthrough how you can take advantage of SQL CE and VS 2010 SP1 using both an ASP.NET Web Forms and an ASP.NET MVC based application. Specifically, we’ll walkthrough: How to create a SQL CE database using VS 2010 SP1, then use the EF4 visual designers in Visual Studio to construct a model layer from it, and then display and edit the data using an ASP.NET GridView control. How to use an EF Code First approach to define a model layer using POCO classes and then have EF Code-First “auto-create” a SQL CE database for us based on our model classes.  We’ll then look at how we can use the new VS 2010 SP1 support for SQL CE to inspect the database that was created, populate it with data, and later make schema changes to it.  We’ll do all this within the context of an ASP.NET MVC based application. You can follow the two walkthroughs below on your own machine by installing VS 2010 SP1 (beta) and then installing the SQL CE Tools for Visual Studio download (which is a separate download that enables SQL CE tooling support for VS 2010 SP1). Walkthrough 1: Create a SQL CE Database, Create EF Model Classes, Edit the Data with a GridView This first walkthrough will demonstrate how to create and define a SQL CE database within an ASP.NET Web Form application.  We’ll then build an EF model layer for it and use that model layer to enable data editing scenarios with an <asp:GridView> control. Step 1: Create a new ASP.NET Web Forms Project We’ll begin by using the File->New Project menu command within Visual Studio to create a new ASP.NET Web Forms project.  We’ll use the “ASP.NET Web Application” project template option so that it has a default UI skin implemented: Step 2: Create a SQL CE Database Right click on the “App_Data” folder within the created project and choose the “Add->New Item” menu command: This will bring up the “Add Item” dialog box.  Select the “SQL Server Compact 4.0 Local Database” item (new in VS 2010 SP1) and name the database file to create “Store.sdf”: Note that SQL CE database files have a .sdf filename extension. Place them within the /App_Data folder of your ASP.NET application to enable easy deployment. When we clicked the “Add” button above a Store.sdf file was added to our project: Step 3: Adding a “Products” Table Double-clicking the “Store.sdf” database file will open it up within the Server Explorer tab.  Since it is a new database there are no tables within it: Right click on the “Tables” icon and choose the “Create Table” menu command to create a new database table.  We’ll name the new table “Products” and add 4 columns to it.  We’ll mark the first column as a primary key (and make it an identify column so that its value will automatically increment with each new row): When we click “ok” our new Products table will be created in the SQL CE database. Step 4: Populate with Data Once our Products table is created it will show up within the Server Explorer.  We can right-click it and choose the “Show Table Data” menu command to edit its data: Let’s add a few sample rows of data to it: Step 5: Create an EF Model Layer We have a SQL CE database with some data in it – let’s now create an EF Model Layer that will provide a way for us to easily query and update data within it. Let’s right-click on our project and choose the “Add->New Item” menu command.  This will bring up the “Add New Item” dialog – select the “ADO.NET Entity Data Model” item within it and name it “Store.edmx” This will add a new Store.edmx item to our solution explorer and launch a wizard that allows us to quickly create an EF model: Select the “Generate From Database” option above and click next.  Choose to use the Store.sdf SQL CE database we just created and then click next again.  The wizard will then ask you what database objects you want to import into your model.  Let’s choose to import the “Products” table we created earlier: When we click the “Finish” button Visual Studio will open up the EF designer.  It will have a Product entity already on it that maps to the “Products” table within our SQL CE database: The VS 2010 SP1 EF designer works exactly the same with SQL CE as it does already with SQL Server and SQL Express.  The Product entity above will be persisted as a class (called “Product”) that we can programmatically work against within our ASP.NET application. Step 6: Compile the Project Before using your model layer you’ll need to build your project.  Do a Ctrl+Shift+B to compile the project, or use the Build->Build Solution menu command. Step 7: Create a Page that Uses our EF Model Layer Let’s now create a simple ASP.NET Web Form that contains a GridView control that we can use to display and edit the our Products data (via the EF Model Layer we just created). Right-click on the project and choose the Add->New Item command.  Select the “Web Form from Master Page” item template, and name the page you create “Products.aspx”.  Base the master page on the “Site.Master” template that is in the root of the project. Add an <h2>Products</h2> heading the new Page, and add an <asp:gridview> control within it: Then click the “Design” tab to switch into design-view. Select the GridView control, and then click the top-right corner to display the GridView’s “Smart Tasks” UI: Choose the “New data source…” drop down option above.  This will bring up the below dialog which allows you to pick your Data Source type: Select the “Entity” data source option – which will allow us to easily connect our GridView to the EF model layer we created earlier.  This will bring up another dialog that allows us to pick our model layer: Select the “StoreEntities” option in the dropdown – which is the EF model layer we created earlier.  Then click next – which will allow us to pick which entity within it we want to bind to: Select the “Products” entity in the above dialog – which indicates that we want to bind against the “Product” entity class we defined earlier.  Then click the “Enable automatic updates” checkbox to ensure that we can both query and update Products.  When you click “Finish” VS will wire-up an <asp:EntityDataSource> to your <asp:GridView> control: The last two steps we’ll do will be to click the “Enable Editing” checkbox on the Grid (which will cause the Grid to display an “Edit” link on each row) and (optionally) use the Auto Format dialog to pick a UI template for the Grid. Step 8: Run the Application Let’s now run our application and browse to the /Products.aspx page that contains our GridView.  When we do so we’ll see a Grid UI of the Products within our SQL CE database. Clicking the “Edit” link for any of the rows will allow us to edit their values: When we click “Update” the GridView will post back the values, persist them through our EF Model Layer, and ultimately save them within our SQL CE database. Learn More about using EF with ASP.NET Web Forms Read this tutorial series on the http://asp.net site to learn more about how to use EF with ASP.NET Web Forms.  The tutorial series uses SQL Express as the database – but the nice thing is that all of the same steps/concepts can also now also be done with SQL CE.   Walkthrough 2: Using EF Code-First with SQL CE and ASP.NET MVC 3 We used a database-first approach with the sample above – where we first created the database, and then used the EF designer to create model classes from the database.  In addition to supporting a designer-based development workflow, EF also enables a more code-centric option which we call “code first development”.  Code-First Development enables a pretty sweet development workflow.  It enables you to: Define your model objects by simply writing “plain old classes” with no base classes or visual designer required Use a “convention over configuration” approach that enables database persistence without explicitly configuring anything Optionally override the convention-based persistence and use a fluent code API to fully customize the persistence mapping Optionally auto-create a database based on the model classes you define – allowing you to start from code first I’ve done several blog posts about EF Code First in the past – I really think it is great.  The good news is that it also works very well with SQL CE. The combination of SQL CE, EF Code First, and the new VS tooling support for SQL CE, enables a pretty nice workflow.  Below is a simple example of how you can use them to build a simple ASP.NET MVC 3 application. Step 1: Create a new ASP.NET MVC 3 Project We’ll begin by using the File->New Project menu command within Visual Studio to create a new ASP.NET MVC 3 project.  We’ll use the “Internet Project” template so that it has a default UI skin implemented: Step 2: Use NuGet to Install EFCodeFirst Next we’ll use the NuGet package manager (automatically installed by ASP.NET MVC 3) to add the EFCodeFirst library to our project.  We’ll use the Package Manager command shell to do this.  Bring up the package manager console within Visual Studio by selecting the View->Other Windows->Package Manager Console menu command.  Then type: install-package EFCodeFirst within the package manager console to download the EFCodeFirst library and have it be added to our project: When we enter the above command, the EFCodeFirst library will be downloaded and added to our application: Step 3: Build Some Model Classes Using a “code first” based development workflow, we will create our model classes first (even before we have a database).  We create these model classes by writing code. For this sample, we will right click on the “Models” folder of our project and add the below three classes to our project: The “Dinner” and “RSVP” model classes above are “plain old CLR objects” (aka POCO).  They do not need to derive from any base classes or implement any interfaces, and the properties they expose are standard .NET data-types.  No data persistence attributes or data code has been added to them.   The “NerdDinners” class derives from the DbContext class (which is supplied by EFCodeFirst) and handles the retrieval/persistence of our Dinner and RSVP instances from a database. Step 4: Listing Dinners We’ve written all of the code necessary to implement our model layer for this simple project.  Let’s now expose and implement the URL: /Dinners/Upcoming within our project.  We’ll use it to list upcoming dinners that happen in the future. We’ll do this by right-clicking on our “Controllers” folder and select the “Add->Controller” menu command.  We’ll name the Controller we want to create “DinnersController”.  We’ll then implement an “Upcoming” action method within it that lists upcoming dinners using our model layer above.  We will use a LINQ query to retrieve the data and pass it to a View to render with the code below: We’ll then right-click within our Upcoming method and choose the “Add-View” menu command to create an “Upcoming” view template that displays our dinners.  We’ll use the “empty” template option within the “Add View” dialog and write the below view template using Razor: Step 4: Configure our Project to use a SQL CE Database We have finished writing all of our code – our last step will be to configure a database connection-string to use. We will point our NerdDinners model class to a SQL CE database by adding the below <connectionString> to the web.config file at the top of our project: EF Code First uses a default convention where context classes will look for a connection-string that matches the DbContext class name.  Because we created a “NerdDinners” class earlier, we’ve also named our connectionstring “NerdDinners”.  Above we are configuring our connection-string to use SQL CE as the database, and telling it that our SQL CE database file will live within the \App_Data directory of our ASP.NET project. Step 5: Running our Application Now that we’ve built our application, let’s run it! We’ll browse to the /Dinners/Upcoming URL – doing so will display an empty list of upcoming dinners: You might ask – but where did it query to get the dinners from? We didn’t explicitly create a database?!? One of the cool features that EF Code-First supports is the ability to automatically create a database (based on the schema of our model classes) when the database we point it at doesn’t exist.  Above we configured  EF Code-First to point at a SQL CE database in the \App_Data\ directory of our project.  When we ran our application, EF Code-First saw that the SQL CE database didn’t exist and automatically created it for us. Step 6: Using VS 2010 SP1 to Explore our newly created SQL CE Database Click the “Show all Files” icon within the Solution Explorer and you’ll see the “NerdDinners.sdf” SQL CE database file that was automatically created for us by EF code-first within the \App_Data\ folder: We can optionally right-click on the file and “Include in Project" to add it to our solution: We can also double-click the file (regardless of whether it is added to the project) and VS 2010 SP1 will open it as a database we can edit within the “Server Explorer” tab of the IDE. Below is the view we get when we double-click our NerdDinners.sdf SQL CE file.  We can drill in to see the schema of the Dinners and RSVPs tables in the tree explorer.  Notice how two tables - Dinners and RSVPs – were automatically created for us within our SQL CE database.  This was done by EF Code First when we accessed the NerdDinners class by running our application above: We can right-click on a Table and use the “Show Table Data” command to enter some upcoming dinners in our database: We’ll use the built-in editor that VS 2010 SP1 supports to populate our table data below: And now when we hit “refresh” on the /Dinners/Upcoming URL within our browser we’ll see some upcoming dinners show up: Step 7: Changing our Model and Database Schema Let’s now modify the schema of our model layer and database, and walkthrough one way that the new VS 2010 SP1 Tooling support for SQL CE can make this easier.  With EF Code-First you typically start making database changes by modifying the model classes.  For example, let’s add an additional string property called “UrlLink” to our “Dinner” class.  We’ll use this to point to a link for more information about the event: Now when we re-run our project, and visit the /Dinners/Upcoming URL we’ll see an error thrown: We are seeing this error because EF Code-First automatically created our database, and by default when it does this it adds a table that helps tracks whether the schema of our database is in sync with our model classes.  EF Code-First helpfully throws an error when they become out of sync – making it easier to track down issues at development time that you might otherwise only find (via obscure errors) at runtime.  Note that if you do not want this feature you can turn it off by changing the default conventions of your DbContext class (in this case our NerdDinners class) to not track the schema version. Our model classes and database schema are out of sync in the above example – so how do we fix this?  There are two approaches you can use today: Delete the database and have EF Code First automatically re-create the database based on the new model class schema (losing the data within the existing DB) Modify the schema of the existing database to make it in sync with the model classes (keeping/migrating the data within the existing DB) There are a couple of ways you can do the second approach above.  Below I’m going to show how you can take advantage of the new VS 2010 SP1 Tooling support for SQL CE to use a database schema tool to modify our database structure.  We are also going to be supporting a “migrations” feature with EF in the future that will allow you to automate/script database schema migrations programmatically. Step 8: Modify our SQL CE Database Schema using VS 2010 SP1 The new SQL CE Tooling support within VS 2010 SP1 makes it easy to modify the schema of our existing SQL CE database.  To do this we’ll right-click on our “Dinners” table and choose the “Edit Table Schema” command: This will bring up the below “Edit Table” dialog.  We can rename, change or delete any of the existing columns in our table, or click at the bottom of the column listing and type to add a new column.  Below I’ve added a new “UrlLink” column of type “nvarchar” (since our property is a string): When we click ok our database will be updated to have the new column and our schema will now match our model classes. Because we are manually modifying our database schema, there is one additional step we need to take to let EF Code-First know that the database schema is in sync with our model classes.  As i mentioned earlier, when a database is automatically created by EF Code-First it adds a “EdmMetadata” table to the database to track schema versions (and hash our model classes against them to detect mismatches between our model classes and the database schema): Since we are manually updating and maintaining our database schema, we don’t need this table – and can just delete it: This will leave us with just the two tables that correspond to our model classes: And now when we re-run our /Dinners/Upcoming URL it will display the dinners correctly: One last touch we could do would be to update our view to check for the new UrlLink property and render a <a> link to it if an event has one: And now when we refresh our /Dinners/Upcoming we will see hyperlinks for the events that have a UrlLink stored in the database: Summary SQL CE provides a free, embedded, database engine that you can use to easily enable database storage.  With SQL CE 4 you can now take advantage of it within ASP.NET projects and applications (both Web Forms and MVC). VS 2010 SP1 provides tooling support that enables you to easily create, edit and modify SQL CE databases – as well as use the standard EF designer against them.  This allows you to re-use your existing skills and data knowledge while taking advantage of an embedded database option.  This is useful both for small applications (where you don’t need the scalability of a full SQL Server), as well as for development and testing scenarios – where you want to be able to rapidly develop/test your application without having a full database instance.  SQL CE makes it easy to later migrate your data to a full SQL Server or SQL Azure instance if you want to – without having to change any code in your application.  All we would need to change in the above two scenarios is the <connectionString> value within the web.config file in order to have our code run against a full SQL Server.  This provides the flexibility to scale up your application starting from a small embedded database solution as needed. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

  Read the article

• How to use jQuery Date Range Picker plugin in asp.net

  - by alaa9jo

  I stepped by this page: http://www.filamentgroup.com/lab/date_range_picker_using_jquery_ui_16_and_jquery_ui_css_framework/ and let me tell you,this is one of the best and coolest daterangepicker in the web in my opinion,they did a great job with extending the original jQuery UI DatePicker.Of course I made enhancements to the original plugin (fixed few bugs) and added a new option (Clear) to clear the textbox. In this article I well use that updated plugin and show you how to use it in asp.net..you will definitely like it. So,What do I need? 1- jQuery library : you can use 1.3.2 or 1.4.2 which is the latest version so far,in my article I will use the latest version. 2- jQuery UI library (1.8): As I mentioned earlier,daterangepicker plugin is based on the original jQuery UI DatePicker so that library should be included into your page. 3- jQuery DateRangePicker plugin : you can go to the author page or use the modified one (it's included in the attachment),in this article I will use the modified one. 4- Visual Studio 2005 or later : very funny :D,in my article I will use VS 2008. Note: in the attachment,I included all CSS and JS files so don't worry. How to use it? First thing,you will have to include all of the CSS and JS files into your page like this: <script src="Scripts/jquery-1.4.2.min.js" type="text/javascript"></script> <script src="Scripts/jquery-ui-1.8.custom.min.js" type="text/javascript"></script> <script src="Scripts/daterangepicker.jQuery.js" type="text/javascript"></script> <link href="CSS/redmond/jquery-ui-1.8.custom.css" rel="stylesheet" type="text/css" /> <link href="CSS/ui.daterangepicker.css" rel="stylesheet" type="text/css" /> <style type="text/css"> .ui-daterangepicker { font-size: 10px; } </style> Then add this html: <asp:TextBox ID="TextBox1" runat="server" Font-Size="10px"></asp:TextBox><asp:Button ID="SubmitButton" runat="server" Text="Submit" OnClick="SubmitButton_Click" /> <span>First Date:</span><asp:Label ID="FirstDate" runat="server"></asp:Label> <span>Second Date:</span><asp:Label ID="SecondDate" runat="server"></asp:Label> As you can see,it includes TextBox1 which we are going to attach the daterangepicker to it,2 labels to show you later on by code on how to read the date from the textbox and set it to the labels Now we have to attach the daterangepicker to the textbox by using jQuery (Note:visit the author's website for more info on daterangerpicker's options and how to use them): <script type="text/javascript"> $(function() { $("#<%= TextBox1.ClientID %>").attr("readonly", "readonly"); $("#<%= TextBox1.ClientID %>").attr("unselectable", "on"); $("#<%= TextBox1.ClientID %>").daterangepicker({ presetRanges: [], arrows: true, dateFormat: 'd M, yy', clearValue: '', datepickerOptions: { changeMonth: true, changeYear: true} }); }); </script> Finally,add this C# code: protected void SubmitButton_Click(object sender, EventArgs e) { if (TextBox1.Text.Trim().Length == 0) { return; } string selectedDate = TextBox1.Text; if (selectedDate.Contains("-")) { DateTime startDate; DateTime endDate; string[] splittedDates = selectedDate.Split("-".ToCharArray(), StringSplitOptions.RemoveEmptyEntries); if (splittedDates.Count() == 2 && DateTime.TryParse(splittedDates[0], out startDate) && DateTime.TryParse(splittedDates[1], out endDate)) { FirstDate.Text = startDate.ToShortDateString(); SecondDate.Text = endDate.ToShortDateString(); } else { //maybe the client has modified/altered the input i.e. hacking tools } } else { DateTime selectedDateObj; if (DateTime.TryParse(selectedDate, out selectedDateObj)) { FirstDate.Text = selectedDateObj.ToShortDateString(); SecondDate.Text = string.Empty; } else { //maybe the client has modified/altered the input i.e. hacking tools } } } This is the way on how to read from the textbox,That's it!. FAQ: 1-Why did you add this code?: <style type="text/css"> .ui-daterangepicker { font-size: 10px; } </style> A:For two reasons: 1)To show the Daterangepicker in a smaller size because it's original size is huge 2)To show you how to control the size of it. 2- Can I change the theme? A: yes you can,you will notice that I'm using Redmond theme which you will find it in jQuery UI website,visit their website and download a different theme,you may also have to make modifications to the css of daterangepicker,it's all yours. 3- Why did you add a font size to the textbox? A: To make the design look better,try to remove it and see by your self. 4- Can I register the script at codebehind? A: yes you can 5- I see you have added these two lines,what they do? $("#<%= TextBox1.ClientID %>").attr("readonly", "readonly"); $("#<%= TextBox1.ClientID %>").attr("unselectable", "on"); A:The first line will make the textbox not editable by the user,the second will block the blinking typing cursor from appearing if the user clicked on the textbox,you will notice that both lines are necessary to be used together,you can't just use one of them...for logical reasons of course. Finally,I hope everyone liked the article and as always,your feedbacks are always welcomed and if anyone have any suggestions or made any modifications that might be useful for anyone else then please post it at at the author's website and post a reference to your post here.

  Read the article

• Adding Client Validation To DataAnnotations DataType Attribute

  - by srkirkland

  The System.ComponentModel.DataAnnotations namespace contains a validation attribute called DataTypeAttribute, which takes an enum specifying what data type the given property conforms to.  Here are a few quick examples: public class DataTypeEntity { [DataType(DataType.Date)] public DateTime DateTime { get; set; }   [DataType(DataType.EmailAddress)] public string EmailAddress { get; set; } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } This attribute comes in handy when using ASP.NET MVC, because the type you specify will determine what “template” MVC uses.  Thus, for the DateTime property if you create a partial in Views/[loc]/EditorTemplates/Date.ascx (or cshtml for razor), that view will be used to render the property when using any of the Html.EditorFor() methods. One thing that the DataType() validation attribute does not do is any actual validation.  To see this, let’s take a look at the EmailAddress property above.  It turns out that regardless of the value you provide, the entity will be considered valid: //valid new DataTypeEntity {EmailAddress = "Foo"}; .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Hmmm.  Since DataType() doesn’t validate, that leaves us with two options: (1) Create our own attributes for each datatype to validate, like [Date], or (2) add validation into the DataType attribute directly.  In this post, I will show you how to hookup client-side validation to the existing DataType() attribute for a desired type.  From there adding server-side validation would be a breeze and even writing a custom validation attribute would be simple (more on that in future posts). Validation All The Way Down Our goal will be to leave our DataTypeEntity class (from above) untouched, requiring no reference to System.Web.Mvc.  Then we will make an ASP.NET MVC project that allows us to create a new DataTypeEntity and hookup automatic client-side date validation using the suggested “out-of-the-box” jquery.validate bits that are included with ASP.NET MVC 3.  For simplicity I’m going to focus on the only DateTime field, but the concept is generally the same for any other DataType. Building a DataTypeAttribute Adapter To start we will need to build a new validation adapter that we can register using ASP.NET MVC’s DataAnnotationsModelValidatorProvider.RegisterAdapter() method.  This method takes two Type parameters; The first is the attribute we are looking to validate with and the second is an adapter that should subclass System.Web.Mvc.ModelValidator. Since we are extending DataAnnotations we can use the subclass of ModelValidator called DataAnnotationsModelValidator<>.  This takes a generic argument of type DataAnnotations.ValidationAttribute, which lucky for us means the DataTypeAttribute will fit in nicely. So starting from there and implementing the required constructor, we get: public class DataTypeAttributeAdapter : DataAnnotationsModelValidator<DataTypeAttribute> { public DataTypeAttributeAdapter(ModelMetadata metadata, ControllerContext context, DataTypeAttribute attribute) : base(metadata, context, attribute) { } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Now you have a full-fledged validation adapter, although it doesn’t do anything yet.  There are two methods you can override to add functionality, IEnumerable<ModelValidationResult> Validate(object container) and IEnumerable<ModelClientValidationRule> GetClientValidationRules().  Adding logic to the server-side Validate() method is pretty straightforward, and for this post I’m going to focus on GetClientValidationRules(). Adding a Client Validation Rule Adding client validation is now incredibly easy because jquery.validate is very powerful and already comes with a ton of validators (including date and regular expressions for our email example).  Teamed with the new unobtrusive validation javascript support we can make short work of our ModelClientValidationDateRule: public class ModelClientValidationDateRule : ModelClientValidationRule { public ModelClientValidationDateRule(string errorMessage) { ErrorMessage = errorMessage; ValidationType = "date"; } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } If your validation has additional parameters you can the ValidationParameters IDictionary<string,object> to include them.  There is a little bit of conventions magic going on here, but the distilled version is that we are defining a “date” validation type, which will be included as html5 data-* attributes (specifically data-val-date).  Then jquery.validate.unobtrusive takes this attribute and basically passes it along to jquery.validate, which knows how to handle date validation. Finishing our DataTypeAttribute Adapter Now that we have a model client validation rule, we can return it in the GetClientValidationRules() method of our DataTypeAttributeAdapter created above.  Basically I want to say if DataType.Date was provided, then return the date rule with a given error message (using ValidationAttribute.FormatErrorMessage()).  The entire adapter is below: public class DataTypeAttributeAdapter : DataAnnotationsModelValidator<DataTypeAttribute> { public DataTypeAttributeAdapter(ModelMetadata metadata, ControllerContext context, DataTypeAttribute attribute) : base(metadata, context, attribute) { }   public override System.Collections.Generic.IEnumerable<ModelClientValidationRule> GetClientValidationRules() { if (Attribute.DataType == DataType.Date) { return new[] { new ModelClientValidationDateRule(Attribute.FormatErrorMessage(Metadata.GetDisplayName())) }; }   return base.GetClientValidationRules(); } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Putting it all together Now that we have an adapter for the DataTypeAttribute, we just need to tell ASP.NET MVC to use it.  The easiest way to do this is to use the built in DataAnnotationsModelValidatorProvider by calling RegisterAdapter() in your global.asax startup method. DataAnnotationsModelValidatorProvider.RegisterAdapter(typeof(DataTypeAttribute), typeof(DataTypeAttributeAdapter)); .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Show and Tell Let’s see this in action using a clean ASP.NET MVC 3 project.  First make sure to reference the jquery, jquery.vaidate and jquery.validate.unobtrusive scripts that you will need for client validation. Next, let’s make a model class (note we are using the same built-in DataType() attribute that comes with System.ComponentModel.DataAnnotations). public class DataTypeEntity { [DataType(DataType.Date, ErrorMessage = "Please enter a valid date (ex: 2/14/2011)")] public DateTime DateTime { get; set; } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Then we make a create page with a strongly-typed DataTypeEntity model, the form section is shown below (notice we are just using EditorForModel): @using (Html.BeginForm()) { @Html.ValidationSummary(true) <fieldset> <legend>Fields</legend>   @Html.EditorForModel()   <p> <input type="submit" value="Create" /> </p> </fieldset> } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } The final step is to register the adapter in our global.asax file: DataAnnotationsModelValidatorProvider.RegisterAdapter(typeof(DataTypeAttribute), typeof(DataTypeAttributeAdapter)); Now we are ready to run the page: Looking at the datetime field’s html, we see that our adapter added some data-* validation attributes: <input type="text" value="1/1/0001" name="DateTime" id="DateTime" data-val-required="The DateTime field is required." data-val-date="Please enter a valid date (ex: 2/14/2011)" data-val="true" class="text-box single-line valid"> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Here data-val-required was added automatically because DateTime is non-nullable, and data-val-date was added by our validation adapter.  Now if we try to add an invalid date: Our custom error message is displayed via client-side validation as soon as we tab out of the box.  If we didn’t include a custom validation message, the default DataTypeAttribute “The field {0} is invalid” would have been shown (of course we can change the default as well).  Note we did not specify server-side validation, but in this case we don’t have to because an invalid date will cause a server-side error during model binding. Conclusion I really like how easy it is to register new data annotations model validators, whether they are your own or, as in this post, supplements to existing validation attributes.  I’m still debating about whether adding the validation directly in the DataType attribute is the correct place to put it versus creating a dedicated “Date” validation attribute, but it’s nice to know either option is available and, as we’ve seen, simple to implement. I’m also working through the nascent stages of an open source project that will create validation attribute extensions to the existing data annotations providers using similar techniques as seen above (examples: Email, Url, EqualTo, Min, Max, CreditCard, etc).  Keep an eye on this blog and subscribe to my twitter feed (@srkirkland) if you are interested for announcements.

  Read the article

• CodePlex Daily Summary for Thursday, November 18, 2010

  CodePlex Daily Summary for Thursday, November 18, 2010Popular ReleasesSitefinity Migration Tool: Sitefinity Migration Tool 0.2 Alpha: - Improvements for the Sitefinity RC releaseMiniTwitter: 1.57: MiniTwitter 1.57 ???? ?? ?????????????????? ?? User Streams ????????????????????? ???????????????·??????·???????VFPX: VFP2C32 2.0.0.7: fixed a bug in AAverage - NULL values in the array corrupted the result removed limitation in ASum, AMin, AMax, AAverage - the functions were limited to 65000 elements, now they're limited to 65000 rows ASplitStr now returns a 1 element array with an empty string when an empty string is passed (behaves more like ALINES) internal code cleanup and optimization: optimized FoxArray class - results in a speedup of 10-20% in many functions which return the result in an array - like AProcesses...Microsoft SQL Server Product Samples: Database: AdventureWorks 2008R2 SR1: Sample Databases for Microsoft SQL Server 2008R2 (SR1)This release is dedicated to the sample databases that ship for Microsoft SQL Server 2008R2. See Database Prerequisites for SQL Server 2008R2 for feature configurations required for installing the sample databases. See Installing SQL Server 2008R2 Databases for step by step installation instructions. The SR1 release contains minor bug fixes to the installer used to create the sample databases. There are no changes to the databases them...VidCoder: 0.7.2: Fixed duplicated subtitles when running multiple encodes off of the same title.Razor Templating Engine: Razor Template Engine v1.1: Release 1.1 Changes: ADDED: Signed assemblies with strong name to allow assemblies to be referenced by other strongly-named assemblies. FIX: Filter out dynamic assemblies which causes failures in template compilation. FIX: Changed ASCII to UTF8 encoding to support UTF-8 encoded string templates. FIX: Corrected implementation of TemplateBase adding ITemplate interface.Prism Training Kit: Prism Training Kit - 1.1: This is an updated version of the Prism training Kit that targets Prism 4.0 and fixes the bugs reported in the version 1.0. This release consists of a Training Kit with Labs on the following topics Modularity Dependency Injection Bootstrapper UI Composition Communication Note: Take into account that this is a Beta version. If you find any bugs please report them in the Issue Tracker PrerequisitesVisual Studio 2010 Microsoft Word 2007/2010 Microsoft Silverlight 4 Microsoft S...Craig's Utility Library: Craig's Utility Library Code 2.0: This update contains a number of changes, added functionality, and bug fixes: Added transaction support to SQLHelper. Added linked/embedded resource ability to EmailSender. Updated List to take into account new functions. Added better support for MAC address in WMI classes. Fixed Parsing in Reflection class when dealing with sub classes. Fixed bug in SQLHelper when replacing the Command that is a select after doing a select. Fixed issue in SQL Server helper with regard to generati...MFCMAPI: November 2010 Release: Build: 6.0.0.1023 Full release notes at SGriffin's blog. If you just want to run the tool, get the executable. If you want to debug it, get the symbol file and the source. The 64 bit build will only work on a machine with Outlook 2010 64 bit installed. All other machines should use the 32 bit build, regardless of the operating system. Facebook BadgeDotNetNuke® Community Edition: 05.06.00: Major HighlightsAdded automatic portal alias creation for single portal installs Updated the file manager upload page to allow user to upload multiple files without returning to the file manager page. Fixed issue with Event Log Email Notifications. Fixed issue where Telerik HTML Editor was unable to upload files to secure or database folder. Fixed issue where registration page is not set correctly during an upgrade. Fixed issue where Sendmail stripped HTML and Links from emails...mVu Mobile Viewer: mVu Mobile Viewer 0.7.10.0: Tube8 fix.EPPlus-Create advanced Excel 2007 spreadsheets on the server: EPPlus 2.8.0.1: EPPlus-Create advanced Excel 2007 spreadsheets on the serverNew Features Improved chart support Different chart-types series on the same chart Support for secondary axis and a lot of new properties Better styling Encryption and Workbook protection Table support Import csv files Array formulas ...and a lot of bugfixesAutoLoL: AutoLoL v1.4.2: Added support for more clients (French and Russian) Settings are now stored sepperatly for each user on a computer Auto Login is much faster now Auto Login detects and handles caps lock state properly nowTailspinSpyworks - WebForms Sample Application: TailspinSpyworks-v0.9: Contains a number of bug fixes and additional tutorial steps as well as complete database implementation details.ASP.NET MVC Project Awesome (rich jQuery AJAX helpers): 1.3 and demos: a library with mvc helpers and a demo project that demonstrates an awesome way of doing asp.net mvc. tested on mozilla, safari, chrome, opera, ie 9b/8/7/6 new stuff in 1.3 Autocomplete helper Autocomplete and AjaxDropdown can have parentId and be filled with data depending on the value of the parent PopupForm besides Content("ok") on success can also return Json(data) and use 'data' in a client side function Awesome demo improved (cruder, builder, added service layer)Nearforums - ASP.NET MVC forum engine: Nearforums v4.1: Version 4.1 of the ASP.NET MVC forum engine, with great improvements: TinyMCE added as visual editor for messages (removed CKEditor). Integrated AntiSamy for cleaner html user post and add more prevention to potential injections. Admin status page: a page for the site admin to check the current status of the configuration / db / etc. View Roadmap for more details.UltimateJB: UltimateJB 2.01 PL3 KakaRoto + PSNYes by EvilSperm: Voici une version attendu avec impatience pour beaucoup : - La Version PSNYes pour pouvoir jouer sur le PSN avec une PS3 Jailbreaker. - Pour l'instant le PSNYes n'est disponible qu'avec les PS3 en firmwares 3.41 !!! - La version PL3 KAKAROTO intégre ses dernières modification et prépare a l'intégration du Firmware 3.30 !!! Conclusion : - UltimateJB PSNYes => Valide l'utilisation du PSN : Uniquement compatible avec les 3.41 - ultimateJB DEFAULT => Pas de PSN mais disponible pour les PS3 sui...Fluent Ribbon Control Suite: Fluent Ribbon Control Suite 2.0: Fluent Ribbon Control Suite 2.0(supports .NET 4.0 RTM and .NET 3.5) Includes: Fluent.dll (with .pdb and .xml) Showcase Application Samples (only for .NET 4.0) Foundation (Tabs, Groups, Contextual Tabs, Quick Access Toolbar, Backstage) Resizing (ribbon reducing & enlarging principles) Galleries (Gallery in ContextMenu, InRibbonGallery) MVVM (shows how to use this library with Model-View-ViewModel pattern) KeyTips ScreenTips Toolbars ColorGallery NEW! *Walkthrough (documenta...patterns & practices: Prism: Prism 4 Documentation: This release contains the Prism 4 documentation in Help 1.0 (CHM) format and PDF format. The documentation is also included with the full download of the guidance. Note: If you cannot view the content of the CHM, using Windows Explorer, select the properties for the file and then click Unblock on the General tab. Note: The PDF version of the guidance is provided for printing and reading in book format. The online version of the Prism 4 documentation can be read here.Farseer Physics Engine: Farseer Physics Engine 3.1: DonationsIf you like this release and would like to keep Farseer Physics Engine running, please consider a small donation. What's new?We bring a lot of new features in Farseer Physics Engine 3.1. Just to name a few: New Box2D core Rope joint added More stable CCD algorithm YuPeng clipper Explosives logic New Constrained Delaunay Triangulation algorithm from the Poly2Tri project. New Flipcode triangulation algorithm. Silverlight 4 samples Silverlight 4 debug view XNA 4.0 relea...New Projectsbizicosoft crm: crmBlog Migrator: The Blog Migrator tool is an all purpose utility designed to help transition a blog from one platform to another. It leverages XML-RPC, BlogML, and WordPress WXR formats. It also provides the ability to "rewrite" your posts on your old blog to point to the new location.bzr-tfs integration tests: Used to test bzr-tfs integrationC++ Open Source Advanced Operating System: C++ Open Source Advanced Operating System is a project which allows starter developers create their own OS. For now it is at a really initial stage.Chavah - internet radio for Yeshua's disciples: Chavah (pronounced "ha-vah") is internet radio for Yeshua's disciples. Inspired by Pandora, Chavah is a Silverlight application that brings community-driven Messianic Jewish tunes for the Lord over the web to your eager ears.CodePoster: An add-in for Visual Studio which allows you to post code directly from Visual Studio to your blog. CRM 2011 Plugin Testing Tools: This solution is meant to make unit testing of plugins in CRM 2011 a simpler and more efficient process. This solution serializes the objects that the CRM server passes to a plugin on execution and then offers a library that allows you to deserialize them in a unit test.Edinamarry Free Tarot Software for Windows: A freeware yet an advanced Tarot reading divinity Software for Psychics and for all those who practice Divinity and Spirituality. This software includes Tarot Spread Designer, Tarot Deck Designer, Tarot Cards Gallery, Client & Customer Profile, Word Editor, Tarot Reader, etc.EPiSocial: Social addons for EPiServer.first team foundation project: this is my first project for the student to teach them about the ms visual studio 201o and team foundation serverFKTdev: Proyecto donde subiremos las pruebas, códigos de ejemplo y demás recursos en nuestro aprendizaje en XNA, hasta que comencemos un desarrollo estable.Gardens Point Component Pascal: Gardens Point Component Pascal is an implementation for .NET of the Component Pascal Language (CP). CP is an object oriented version of Pascal, and shares many design features with Oberon-2. Geoinformatics: geoinformaticsGREENHOUSEMANAGER: GREENHOUSE es un proyecto universitario para manejar los distintos aspectos de un invernadero. El sistema esta desarrollado en c# con interfaz grafica en WPFHousing: This project is only for the asp.net learning. HR-XML.NET: A .NET HR-XML Serialization Library. Also supports the Dutch SETU standard and some proprietary extensions used in the Netherlands. The project is currently targeting HR-XML version 2.5 and Setu standard 2008-01.InternetShop2: ShopLesson4: Lesson4 for M.Logical Synchronous Circuit Simulator: As part of a student project, we are trying to make a logic synchronous circuit simulator, with the ultimate goal of simulating a processor and a digital clock running on it.MediaOwl: MediaOwl is a music (albums, artists, tracks, tags) and movie (movies, series, actors, directors, genres) search engine, but above all, it is a Microsoft Silverlight 4 application (C#), that shows how to use Caliburn Micro.N2F Yverdon Solar Flare Reflector: The solar flare reflector provides minimal base-range protection for your N2F Yverdon installation against solar flare interference.Netduino Plus Home Automation Toolkit: The Netduino Plus Home Automation project is designed to proivde a communication platform from various consumer based home automation products that offer a common web service endpoint. This will hopefully create a low cost DIY alternative to the expensive ethernet interfaces.NRapid: NRapidOfficeHelper: Wrapper around the open xml office package. You can easily create xlsx documents based on a template xlsx document and reuse parts from that document, if you mark them as named ranges (i.e. "names").OffProjects: This is a private project which for my dev investigationParis Velib Stations for Windows Mobile: Allow to find the closest Velib bike station in Paris on a Windows Mobile Phone (6.5)/ Permet de trouver la station de Vélib la plus proche dans Paris ainsi que ses informations sur un smartphone Windows MobilePolarConverter: Adjust the measured distance of HRM files created by Polar Heart Rate monitorsSexy Select: a jQuery plugin that allows for easy manipulation of select options. Allows for adding, removing, sorting, validation and custom skinningSilverlight Progress Feedback: Demonstrates how to get progress feedback from slow running WPF processes in Silverlight.Silverlight Tabbed Panel: Tabbed Panel based on Silverlight targeted for both developers and designers audience. Tabbed Control is used in this project. This is a basic application. More features will be added in further releases. XAML has been used to design this panel. slabhid: SLABHIDDevice.dll is used for the SLAB MCU example code on PC, the original source code is written by C++. This wrapper class brings SLABHIDDevice.dll to the .Net world, so it will be possible to make some quick solution for firmware testing purpose.SuperWebSocket: A .NET server side implementation of WebSocket protocol.test1-jjoiner: just a test projectTotem Alpha Developer Framework For .Net: ????tadf??VS.NET???????????，????jtadf???????????????。 ?????????tadf??????????????J2EE???????VS.NET?????????，??tadf?????.NET??，???????????，????????????，??????C#??????????Java???????，??????。 tadf?????????????，????HTML???????????，???????，?????????，?????。tadf???????????，????????RICH UI?????WEB??。??????，??。 tadf?????????????????????，????WEB??????????。???????，???????????，?Ajax???????，????????????????，????????，????????????????。???????????，???????????????????????????????，?xml??????，?????????????xml...Ukázkové projekty: Obsahuje ukázkové projekty uživatele TenCoKaciStromy.WPFDemo: This Peoject is only for the WPF learning.Xinx TimeIt!: TinyAlarm is a small utility that allows you to configure an Alarm so that you can opt for 1. Shutdown computer 2. Play a sound 3. Show a note with sound 4. Disconnect a dial-up connection 5. Connect via dial-up connection

  Read the article

• Talks Submitted for Ann Arbor Day of .NET 2010

  - by PSteele

  Just submitted my session abstracts for Ann Arbor's Day of .NET 2010.   Getting up to speed with .NET 3.5 -- Just in time for 4.0! Yes, C# 4.0 is just around the corner.  But if you haven't had the chance to use C# 3.5 extensively, this session will start from the ground up with the new features of 3.5.  We'll assume everyone is coming from C# 2.0.  This session will show you the details of extension methods, partial methods and more.  We'll also show you how LINQ -- Language Integrated Query -- can help decrease your development time and increase your code's readability.  If time permits, we'll look at some .NET 4.0 features, but the goal is to get you up to speed on .NET 3.5.   Go Ahead and Mock Me! When testing specific parts of your application, there can be a lot of external dependencies required to make your tests work.  Writing fake or mock objects that act as stand-ins for the real dependencies can waste a lot of time.  This is where mocking frameworks come in.  In this session, Patrick Steele will introduce you to Rhino Mocks, a popular mocking framework for .NET.  You'll see how a mocking framework can make writing unit tests easier and leads to less brittle unit tests.   Inversion of Control: Who's got control and why is it being inverted? No doubt you've heard of "Inversion of Control".  If not, maybe you've heard the term "Dependency Injection"?  The two usually go hand-in-hand.  Inversion of Control (IoC) along with Dependency Injection (DI) helps simplify the connections and lifetime of all of the dependent objects in the software you write.  In this session, Patrick Steele will introduce you to the concepts of IoC and DI and will show you how to use a popular IoC container (Castle Windsor) to help simplify the way you build software and how your objects interact with each other. If you're interested in speaking, hurry up and get your submissions in!  The deadline is Monday, April 5th! Technorati Tags: .NET,Ann Arbor,Day of .NET

  Read the article

• Video Recording Not Working in ICS

  - by Nirav Ranpara

  I have implement code Record video in Android Phone . This code is working in 2.2 , 2.3 . not in ICS But when I checked in ICS code is not working ? here I posted code and xml file. videorecord.java import java.io.File; import java.io.IOException; import android.app.Activity; import android.app.AlertDialog; import android.content.Context; import android.content.DialogInterface; import android.content.Intent; import android.content.SharedPreferences; import android.hardware.Camera; import android.media.CamcorderProfile; import android.media.MediaRecorder; import android.os.Bundle; import android.os.CountDownTimer; import android.os.Environment; import android.util.Log; import android.view.Display; import android.view.KeyEvent; import android.view.SurfaceHolder; import android.view.SurfaceView; import android.view.View; import android.widget.EditText; import android.widget.FrameLayout; import android.widget.ImageView; import android.widget.LinearLayout; import android.widget.TextView; import android.widget.Toast; public class videorecord extends Activity{ SharedPreferences.Editor pre; String filename; CountDownTimer t; private Camera myCamera; private MyCameraSurfaceView myCameraSurfaceView; private MediaRecorder mediaRecorder; Integer cnt=0; LinearLayout myButton; TextView myButton1; SurfaceHolder surfaceHolder; boolean recording; private TextView txtcount; private ImageView btnplay; @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); recording = false; setContentView(R.layout.videorecord); init(); myCamera = getCameraInstance(); if(myCamera == null){ } myCameraSurfaceView = new MyCameraSurfaceView(this, myCamera); FrameLayout myCameraPreview = (FrameLayout)findViewById(R.id.videoview); Display display = getWindowManager().getDefaultDisplay(); int width = display.getWidth(); int height = display.getHeight(); myCameraSurfaceView.setLayoutParams(new LinearLayout.LayoutParams(width, height-60)); myCameraPreview.addView(myCameraSurfaceView); myButton = (LinearLayout)findViewById(R.id.mybutton); btnplay.setOnClickListener(myButtonOnClickListener); } private void init() { txtcount = (TextView) findViewById(R.id.txtcounter); //myButton1 = (TextView) findViewById(R.id.mybutton1); btnplay = (ImageView)findViewById(R.id.btnplay); t = new CountDownTimer( Long.MAX_VALUE , 1000) { @Override public void onTick(long millisUntilFinished) { cnt++; String time = new Integer(cnt).toString(); long millis = cnt; int seconds = (int) (millis / 60); int minutes = seconds / 60; seconds = seconds % 60; txtcount.setText(String.format("%d:%02d:%02d", minutes, seconds,millis)); } @Override public void onFinish() { } }; } @Override public boolean onKeyDown(int keyCode, KeyEvent event) { if ((keyCode == KeyEvent.KEYCODE_BACK)) { if(recording) { new AlertDialog.Builder(videorecord.this).setTitle("Do you want to save Video ?") .setPositiveButton("OK", new DialogInterface.OnClickListener() { public void onClick(DialogInterface dialog, int which) { filename(); //finish(); } }).setNegativeButton("Cancle", new DialogInterface.OnClickListener() { public void onClick(DialogInterface dialog, int which) { // TODO Auto-generated method stub } }).show(); } else { if ((keyCode == KeyEvent.KEYCODE_BACK)) { //Intent homeIntent= new Intent(Intent.ACTION_MAIN); //homeIntent.addCategory(Intent.CATEGORY_HOME); //homeIntent.setFlags(Intent.FLAG_ACTIVITY_CLEAR_TOP); //startActivity(homeIntent); //this.finishActivity(1); finish(); } //moveTaskToBack(true); // finish(); return super.onKeyDown(keyCode, event); } } else { // Toast.makeText(getApplicationContext(), "asd", Toast.LENGTH_LONG).show(); android.os.Process.killProcess(android.os.Process.myPid()) ; } return super.onKeyDown(keyCode, event); } ImageView.OnClickListener myButtonOnClickListener = new ImageView.OnClickListener(){ public void onClick(View v) { if(recording){ Log.e("Record error", "error in recording ."); mediaRecorder.stop(); t.cancel(); filename(); releaseMediaRecorder(); }else{ releaseCamera(); Log.e("Record Stop error", "error in recording ."); // if(!prepareMediaRecorder()){ prepareMediaRecorder(); finish(); } mediaRecorder.start(); recording = true; // myButton1.setText("STOP Recording"); // btnplay.setImageResource(android.R.drawable.ic_media_pause); btnplay.setImageResource(R.drawable.stoprec); t.start(); } }}; private Camera getCameraInstance(){ Camera c = null; try { c = Camera.open(); } catch (Exception e){ } return c; } private void filename() { AlertDialog.Builder alert = new AlertDialog.Builder(this); alert.setTitle("Save Video"); alert.setMessage("Enter File Name"); final EditText input = new EditText(this); alert.setView(input); alert.setPositiveButton("Ok", new DialogInterface.OnClickListener() { public void onClick(DialogInterface dialog, int whichButton) { if(input.getText().length()>=1) { filename = input.getText().toString(); File sdcard = new File(Environment.getExternalStorageDirectory() + "/VideoRecord"); File from = new File(sdcard,"null.mp4"); File to = new File(sdcard,filename+".mp4"); from.renameTo(to); SharedPreferences sp = videorecord.this.getSharedPreferences("data", MODE_WORLD_WRITEABLE); pre = sp.edit(); pre.clear(); pre.commit(); pre.putString("lastvideo", filename+".mp4"); pre.commit(); //btnplay.setImageResource(android.R.drawable.ic_media_play); btnplay.setImageResource(R.drawable.startrec); // Intent intent = new Intent(videorecord.this,StopVidoWatch_Activity.class); // startActivity(intent); Intent myIntent = new Intent(getApplicationContext(), StopVidoWatch_Activity.class).setFlags(Intent.FLAG_ACTIVITY_CLEAR_TOP); startActivity(myIntent); } else { filename(); } } }); alert.setNegativeButton("Cancel", new DialogInterface.OnClickListener() { public void onClick(DialogInterface dialog, int whichButton) { // Intent intent = new Intent(videorecord.this,StopVidoWatch_Activity.class); // startActivity(intent); File file = new File(Environment.getExternalStorageDirectory() + "/VideoRecord/null.mp4"); //boolean deleted = file.delete(); file.delete(); finish(); } }); alert.show(); } private boolean prepareMediaRecorder(){ myCamera = getCameraInstance(); mediaRecorder = new MediaRecorder(); myCamera.unlock(); mediaRecorder.setCamera(myCamera); mediaRecorder.setAudioSource(MediaRecorder.AudioSource.CAMCORDER); mediaRecorder.setVideoSource(MediaRecorder.VideoSource.CAMERA); mediaRecorder.setProfile(CamcorderProfile.get(CamcorderProfile.QUALITY_HIGH)); File folder = new File(Environment.getExternalStorageDirectory() + "/VideoRecord"); boolean success = false; if (!folder.exists()) { success = folder.mkdir(); } if (!success) { } else { } mediaRecorder.setOutputFile("/sdcard/VideoRecord/"+filename+".mp4"); mediaRecorder.setMaxDuration(60000); mediaRecorder.setMaxFileSize(5000000); Display display = getWindowManager().getDefaultDisplay(); int width = display.getHeight(); int height = display.getWidth(); String s = new String(); s= s.valueOf(width); String s1 = new String(); s1= s1.valueOf(height); // Toast.makeText(videorecord.this, "Width : " + s , Toast.LENGTH_LONG).show(); // Toast.makeText(videorecord.this, "Height : " + s1 , Toast.LENGTH_LONG).show(); mediaRecorder.setVideoSize(height, width); mediaRecorder.setPreviewDisplay(myCameraSurfaceView.getHolder().getSurface()); try { mediaRecorder.prepare(); } catch (IllegalStateException e) { releaseMediaRecorder(); return false; } catch (IOException e) { releaseMediaRecorder(); return false; } return true; } @Override protected void onPause() { super.onPause(); releaseMediaRecorder(); releaseCamera(); } private void releaseMediaRecorder() { if (mediaRecorder != null) { mediaRecorder.reset(); mediaRecorder.release(); mediaRecorder = null; myCamera.lock(); } } private void releaseCamera(){ if (myCamera != null){ myCamera.release(); myCamera = null; } } public class MyCameraSurfaceView extends SurfaceView implements SurfaceHolder.Callback{ private SurfaceHolder mHolder; private Camera mCamera; public MyCameraSurfaceView(Context context, Camera camera) { super(context); mCamera = camera; mHolder = getHolder(); mHolder.addCallback(this); mHolder.setType(SurfaceHolder.SURFACE_TYPE_PUSH_BUFFERS); } public void surfaceChanged(SurfaceHolder holder, int format, int weight, int height) { if (mHolder.getSurface() == null){ return; } try { mCamera.stopPreview(); } catch (Exception e){ } try { mCamera.setPreviewDisplay(mHolder); mCamera.startPreview(); } catch (Exception e){ } } public void surfaceCreated(SurfaceHolder holder) { try { mCamera.setPreviewDisplay(holder); mCamera.startPreview(); } catch (IOException e) { } } public void surfaceDestroyed(SurfaceHolder holder) { } } } videorecord.xml <?xml version="1.0" encoding="utf-8"?> <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android" android:orientation="vertical" android:layout_width="fill_parent" android:layout_height="fill_parent" > <FrameLayout android:layout_width="fill_parent" android:layout_height="fill_parent" > <FrameLayout android:id="@+id/videoview" android:layout_width="fill_parent" android:layout_height="fill_parent"></FrameLayout> <LinearLayout android:id="@+id/mybutton" android:layout_width="fill_parent" android:layout_marginBottom="0dip" android:layout_height="wrap_content" android:orientation="horizontal" android:layout_weight="0" > <!-- <TextView android:text="START Recording" android:id="@+id/mybutton1" android:layout_height="wrap_content" android:layout_width="wrap_content" style="@style/savestyle" android:layout_weight="1" android:gravity="left" > </TextView> --> <ImageView android:layout_height="wrap_content" android:id="@+id/btnplay" android:padding="5dip" android:background="#A0000000" android:textColor="#ffffffff" android:layout_width="wrap_content" android:src="@drawable/startrec" /> </LinearLayout> <TextView android:text="00:00:00" android:id="@+id/txtcounter" android:layout_width="wrap_content" android:layout_height="wrap_content" android:layout_gravity="right|bottom" android:padding="5dip" android:background="#A0000000" android:textColor="#ffffffff" /> </FrameLayout> <RelativeLayout android:layout_width="fill_parent" android:layout_height="fill_parent" android:background="@color/bgcolor" > <LinearLayout android:layout_above="@+id/mybutton" android:orientation="horizontal" android:layout_width="fill_parent" android:layout_height="fill_parent" > </LinearLayout> </RelativeLayout> </LinearLayout>

  Read the article

• Ops Center 12c - Provisioning Solaris Using a Card-Based NIC

  - by scottdickson

  It's been a long time since last I added something here, but having some conversations this last week, I got inspired to update things. I've been spending a lot of time with Ops Center for managing and installing systems these days.  So, I suspect a number of my upcoming posts will be in that area. Today, I want to look at how to provision Solaris using Ops Center when your network is not connected to one of the built-in NICs.  We'll talk about how this can work for both Solaris 10 and Solaris 11, since they are pretty similar.  In both cases, WANboot is a key piece of the story. Here's what I want to do:  I have a Sun Fire T2000 server with a Quad-GbE nxge card installed.  The only network is connected to port 2 on that card rather than the built-in network interfaces.  I want to install Solaris on it across the network, either Solaris 10 or Solaris 11.  I have met with a lot of customers lately who have a similar architecture.  Usually, they have T4-4 servers with the network connected via 10GbE connections. Add to this mix the fact that I use Ops Center to manage the systems in my lab, so I really would like to add this to Ops Center.  If possible, I would like this to be completely hands free.  I can't quite do that yet. Close, but not quite. WANBoot or Old-Style NetBoot? When a system is installed from the network, it needs some help getting the process rolling.  It has to figure out what its network configuration (IP address, gateway, etc.) ought to be.  It needs to figure out what server is going to help it boot and install, and it needs the instructions for the installation.  There are two different ways to bootstrap an installation of Solaris on SPARC across the network.   The old way uses a broadcast of RARP or more recently DHCP to obtain the IP configuration and the rest of the information needed.  The second is to explicitly configure this information in the OBP and use WANBoot for installation WANBoot has a number of benefits over broadcast-based installation: it is not restricted to a single subnet; it does not require special DHCP configuration or DHCP helpers; it uses standard HTTP and HTTPS protocols which traverse firewalls much more easily than NFS-based package installation.  But, WANBoot is not available on really old hardware and WANBoot requires the use o Flash Archives in Solaris 10.  Still, for many people, this is a great approach. As it turns out, WANBoot is necessary if you plan to install using a NIC on a card rather than a built-in NIC. Identifying Which Network Interface to Use One of the trickiest aspects to this process, and the one that actually requires manual intervention to set up, is identifying how the OBP and Solaris refer to the NIC that we want to use to boot.  The OBP already has device aliases configured for the built-in NICs called net, net0, net1, net2, net3.  The device alias net typically points to net0 so that when you issue the command  "boot net -v install", it uses net0 for the boot.  Our task is to figure out the network instance for the NIC we want to use.  We will need to get to the OBP console of the system we want to install in order to figure out what the network should be called.  I will presume you know how to get to the ok prompt.  Once there, we have to see what networks the OBP sees and identify which one is associated with our NIC using the OBP command show-nets. SunOS Release 5.11 Version 11.0 64-bit Copyright (c) 1983, 2011, Oracle and/or its affiliates. All rights reserved. {4} ok banner Sun Fire T200, No Keyboard Copyright (c) 1998, 2010, Oracle and/or its affiliates. All rights reserved. OpenBoot 4.30.4.b, 32640 MB memory available, Serial #69057548. Ethernet address 0:14:4f:1d:bc:c, Host ID: 841dbc0c. {4} ok show-nets a) /pci@7c0/pci@0/pci@2/network@0,1 b) /pci@7c0/pci@0/pci@2/network@0 c) /pci@780/pci@0/pci@8/network@0,3 d) /pci@780/pci@0/pci@8/network@0,2 e) /pci@780/pci@0/pci@8/network@0,1 f) /pci@780/pci@0/pci@8/network@0 g) /pci@780/pci@0/pci@1/network@0,1 h) /pci@780/pci@0/pci@1/network@0 q) NO SELECTION Enter Selection, q to quit: d /pci@780/pci@0/pci@8/network@0,2 has been selected. Type ^Y ( Control-Y ) to insert it in the command line. e.g. ok nvalias mydev ^Y for creating devalias mydev for /pci@780/pci@0/pci@8/network@0,2 {4} ok devalias ... net3 /pci@7c0/pci@0/pci@2/network@0,1 net2 /pci@7c0/pci@0/pci@2/network@0 net1 /pci@780/pci@0/pci@1/network@0,1 net0 /pci@780/pci@0/pci@1/network@0 net /pci@780/pci@0/pci@1/network@0 ... name aliases By looking at the devalias and the show-nets output, we can see that our Quad-GbE card must be the device nodes starting with  /pci@780/pci@0/pci@8/network@0.  The cable for our network is plugged into the 3rd slot, so the device address for our network must be /pci@780/pci@0/pci@8/network@0,2. With that, we can create a device alias for our network interface.  Naming the device alias may take a little bit of trial and error, especially in Solaris 11 where the device alias seems to matter more with the new virtualized network stack. So far in my testing, since this is the "next" network interface to be used, I have found success in naming it net4, even though it's a NIC in the middle of a card that might, by rights, be called net6 (assuming the 0th interface on the card is the next interface identified by Solaris and this is the 3rd interface on the card).  So, we will call it net4.  We need to assign a device alias to it: {4} ok nvalias net4 /pci@780/pci@0/pci@8/network@0,2 {4} ok devalias net4 /pci@780/pci@0/pci@8/network@0,2 ... We also may need to have the MAC for this particular interface, so let's get it, too.  To do this, we go to the device and interrogate its properties. {4} ok cd /pci@780/pci@0/pci@8/network@0,2 {4} ok .properties assigned-addresses 82060210 00000000 03000000 00000000 01000000 82060218 00000000 00320000 00000000 00008000 82060220 00000000 00328000 00000000 00008000 82060230 00000000 00600000 00000000 00100000 local-mac-address 00 21 28 20 42 92 phy-type mif ... From this, we can see that the MAC for this interface is  00:21:28:20:42:92.  We will need this later. This is all we need to do at the OBP.  Now, we can configure Ops Center to use this interface. Network Boot in Solaris 10 Solaris 10 turns out to be a little simpler than Solaris 11 for this sort of a network boot.  Since WANBoot in Solaris 10 fetches a specified In order to install the system using Ops Center, it is necessary to create a OS Provisioning profile and its corresponding plan.  I am going to presume that you already know how to do this within Ops Center 12c and I will just cover the differences between a regular profile and a profile that can use an alternate interface. Create a OS Provisioning profile for Solaris 10 as usual.  However, when you specify the network resources for the primary network, click on the name of the NIC, probably GB_0, and rename it to GB_N/netN, where N is the instance number you used previously in creating the device alias.  This is where the trial and error may come into play.  You may need to try a few instance numbers before you, the OBP, and Solaris all agree on the instance number.  Mark this as the boot network. For Solaris 10, you ought to be able to then apply the OS Provisioning profile to the server and it should install using that interface.  And if you put your cards in the same slots and plug the networks into the same NICs, this profile is reusable across multiple servers. Why This Works If you watch the console as Solaris boots during the OSP process, Ops Center is going to look for the device alias netN.  Since WANBoot requires a device alias called just net, Ops Center uses the value of your netN device alias and assigns that device to the net alias.  That means that boot net will automatically use this device.  Very cool!  Here's a trace from the console as Ops Center provisions a server: Sun Sun Fire T200, No KeyboardCopyright (c) 1998, 2010, Oracle and/or its affiliates. All rights reserved.OpenBoot 4.30.4.b, 32640 MB memory available, Serial #69057548.Ethernet address 0:14:4f:1d:bc:c, Host ID: 841dbc0c.auto-boot? =            false{0} ok  {0} ok printenv network-boot-argumentsnetwork-boot-arguments =  host-ip=10.140.204.234,router-ip=10.140.204.1,subnet-mask=255.255.254.0,hostname=atl-sewr-52,client-id=0100144F1DBC0C,file=http://10.140.204.22:5555/cgi-bin/wanboot-cgi{0} ok {0} ok devalias net net                      /pci@780/pci@0/pci@1/network@0{0} ok devalias net4 net4                     /pci@780/pci@0/pci@8/network@0,2{0} ok devalias net /pci@780/pci@0/pci@8/network@0,2{0} ok setenv network-boot-arguments host-ip=10.140.204.234,router-ip=10.140.204.1,subnet-mask=255.255.254.0,hostname=atl-sewr-52,client-id=0100144F1DBC0C,file=http://10.140.204.22:8004/cgi-bin/wanboot-cginetwork-boot-arguments =  host-ip=10.140.204.234,router-ip=10.140.204.1,subnet-mask=255.255.254.0,hostname=atl-sewr-52,client-id=0100144F1DBC0C,file=http://10.140.204.22:8004/cgi-bin/wanboot-cgi{0} ok {0} ok boot net - installBoot device: /pci@780/pci@0/pci@8/network@0,2  File and args: - install/pci@780/pci@0/pci@8/network@0,2: 1000 Mbps link up<time unavailable> wanboot info: WAN boot messages->console<time unavailable> wanboot info: configuring /pci@780/pci@0/pci@8/network@0,2 See what happened?  Ops Center looked for the network device alias called net4 that we specified in the profile, took the value from it, and made it the net device alias for the boot.  Pretty cool! WANBoot and Solaris 11 Solaris 11 requires an additional step since the Automated Installer in Solaris 11 uses the MAC address of the network to figure out which manifest to use for system installation.  In order to make sure this is available, we have to take an extra step to associate the MAC of the NIC on the card with the host.  So, in addition to creating the device alias like we did above, we also have to declare to Ops Center that the host has this new MAC. Declaring the NIC Start out by discovering the hardware as usual.  Once you have discovered it, take a look under the Connectivity tab to see what networks it has discovered.  In the case of this system, it shows the 4 built-in networks, but not the networks on the additional cards.  These are not directly visible to the system controller.  In order to add the additional network interface to the hardware asset, it is necessary to Declare it.  We will declare that we have a server with this additional NIC, but we will also  specify the existing GB_0 network so that Ops Center can associate the right resources together.  The GB_0 acts as sort of a key to tie our new declaration to the old system already discovered.  Go to the Assets tab, select All Assets, and then in the Actions tab, select Add Asset.  Rather than going through a discovery this time, we will manually declare a new asset. When we declare it, we will give the hostname, IP address, system model that match those that have already been discovered.  Then, we will declare both GB_0 with its existing MAC and the new GB_4 with its MAC.  Remember that we collected the MAC for GB_4 when we created its device alias. After you declare the asset, you will see the new NIC in the connectivity tab for the asset.  You will notice that only the NICs you listed when you declared it are seen now.  If you want Ops Center to see all of the existing NICs as well as the additional one, declare them as well.  Add the other GB_1, GB_2, GB_3 links and their MACs just as you did GB_0 and GB_4.  Installing the OS  Once you have declared the asset, you can create an OS Provisioning profile for Solaris 11 in the same way that you did for Solaris 10.  The only difference from any other provisioning profile you might have created already is the network to use for installation.  Again, use GB_N/netN where N is the interface number you used for your device alias and in your declaration.  And away you go.  When the system boots from the network, the automated installer (AI) is able to see which system manifest to use, based on the new MAC that was associated, and the system gets installed. {0} ok {0} ok printenv network-boot-argumentsnetwork-boot-arguments =  host-ip=10.140.204.234,router-ip=10.140.204.1,subnet-mask=255.255.254.0,hostname=atl-sewr-52,client-id=01002128204292,file=http://10.140.204.22:5555/cgi-bin/wanboot-cgi{0} ok {0} ok devalias net net                      /pci@780/pci@0/pci@1/network@0{0} ok devalias net4 net4                     /pci@780/pci@0/pci@8/network@0,2{0} ok devalias net /pci@780/pci@0/pci@8/network@0,2{0} ok setenv network-boot-arguments host-ip=10.140.204.234,router-ip=10.140.204.1,subnet-mask=255.255.254.0,hostname=atl-sewr-52,client-id=01002128204292,file=http://10.140.204.22:5555/cgi-bin/wanboot-cginetwork-boot-arguments =  host-ip=10.140.204.234,router-ip=10.140.204.1,subnet-mask=255.255.254.0,hostname=atl-sewr-52,client-id=01002128204292,file=http://10.140.204.22:5555/cgi-bin/wanboot-cgi{0} ok {0} ok boot net - installBoot device: /pci@780/pci@0/pci@8/network@0,2  File and args: - install/pci@780/pci@0/pci@8/network@0,2: 1000 Mbps link up<time unavailable> wanboot info: WAN boot messages->console<time unavailable> wanboot info: configuring /pci@780/pci@0/pci@8/network@0,2...SunOS Release 5.11 Version 11.0 64-bitCopyright (c) 1983, 2011, Oracle and/or its affiliates. All rights reserved.Remounting root read/writeProbing for device nodes ...Preparing network image for useDownloading solaris.zlib--2012-02-17 15:10:17--  http://10.140.204.22:5555/var/js/AI/sparc//solaris.zlibConnecting to 10.140.204.22:5555... connected.HTTP request sent, awaiting response... 200 OKLength: 126752256 (121M) [text/plain]Saving to: `/tmp/solaris.zlib'100%[======================================>] 126,752,256 28.6M/s   in 4.4s    2012-02-17 15:10:21 (27.3 MB/s) - `/tmp/solaris.zlib' saved [126752256/126752256] Conclusion So, why go to all of this trouble?  More and more, I find that customers are wiring their data center to only use higher speed networks - 10GbE only to the hosts.  Some customers are moving aggressively toward consolidated networks combining storage and network on CNA NICs.  All of this means that network-based provisioning cannot rely exclusively on the built-in network interfaces.  So, it's important to be able to provision a system using other than the built-in networks.  Turns out, that this is pretty straight-forward for both Solaris 10 and Solaris 11 and fits into the Ops Center deployment process quite nicely. Hopefully, you will be able to use this as you build out your own private cloud solutions with Ops Center.

  Read the article

• More CPU cores may not always lead to better performance – MAXDOP and query memory distribution in spotlight

  - by sqlworkshops

  More hardware normally delivers better performance, but there are exceptions where it can hinder performance. Understanding these exceptions and working around it is a major part of SQL Server performance tuning.   When a memory allocating query executes in parallel, SQL Server distributes memory to each task that is executing part of the query in parallel. In our example the sort operator that executes in parallel divides the memory across all tasks assuming even distribution of rows. Common memory allocating queries are that perform Sort and do Hash Match operations like Hash Join or Hash Aggregation or Hash Union.   In reality, how often are column values evenly distributed, think about an example; are employees working for your company distributed evenly across all the Zip codes or mainly concentrated in the headquarters? What happens when you sort result set based on Zip codes? Do all products in the catalog sell equally or are few products hot selling items?   One of my customers tested the below example on a 24 core server with various MAXDOP settings and here are the results:MAXDOP 1: CPU time = 1185 ms, elapsed time = 1188 msMAXDOP 4: CPU time = 1981 ms, elapsed time = 1568 msMAXDOP 8: CPU time = 1918 ms, elapsed time = 1619 msMAXDOP 12: CPU time = 2367 ms, elapsed time = 2258 msMAXDOP 16: CPU time = 2540 ms, elapsed time = 2579 msMAXDOP 20: CPU time = 2470 ms, elapsed time = 2534 msMAXDOP 0: CPU time = 2809 ms, elapsed time = 2721 ms - all 24 cores.In the above test, when the data was evenly distributed, the elapsed time of parallel query was always lower than serial query.   Why does the query get slower and slower with more CPU cores / higher MAXDOP? Maybe you can answer this question after reading the article; let me know: [email protected].   Well you get the point, let’s see an example.   The best way to learn is to practice. To create the below tables and reproduce the behavior, join the mailing list by using this link: www.sqlworkshops.com/ml and I will send you the table creation script.   Let’s update the Employees table with 49 out of 50 employees located in Zip code 2001. update Employees set Zip = EmployeeID / 400 + 1 where EmployeeID % 50 = 1 update Employees set Zip = 2001 where EmployeeID % 50 != 1 go update statistics Employees with fullscan go   Let’s create the temporary table #FireDrill with all possible Zip codes. drop table #FireDrill go create table #FireDrill (Zip int primary key) insert into #FireDrill select distinct Zip from Employees update statistics #FireDrill with fullscan go  Let’s execute the query serially with MAXDOP 1. --Example provided by www.sqlworkshops.com --Execute query with uneven Zip code distribution --First serially with MAXDOP 1 set statistics time on go declare @EmployeeID int, @EmployeeName varchar(48),@zip int select @EmployeeName = e.EmployeeName, @zip = e.Zip from Employees e       inner join #FireDrill fd on (e.Zip = fd.Zip)       order by e.Zip option (maxdop 1) goThe query took 1011 ms to complete.   The execution plan shows the 77816 KB of memory was granted while the estimated rows were 799624.  No Sort Warnings in SQL Server Profiler.  Now let’s execute the query in parallel with MAXDOP 0. --Example provided by www.sqlworkshops.com --Execute query with uneven Zip code distribution --In parallel with MAXDOP 0 set statistics time on go declare @EmployeeID int, @EmployeeName varchar(48),@zip int select @EmployeeName = e.EmployeeName, @zip = e.Zip from Employees e       inner join #FireDrill fd on (e.Zip = fd.Zip)       order by e.Zip option (maxdop 0) go The query took 1912 ms to complete.  The execution plan shows the 79360 KB of memory was granted while the estimated rows were 799624.  The estimated number of rows between serial and parallel plan are the same. The parallel plan has slightly more memory granted due to additional overhead. Sort properties shows the rows are unevenly distributed over the 4 threads.   Sort Warnings in SQL Server Profiler.   Intermediate Summary: The reason for the higher duration with parallel plan was sort spill. This is due to uneven distribution of employees over Zip codes, especially concentration of 49 out of 50 employees in Zip code 2001. Now let’s update the Employees table and distribute employees evenly across all Zip codes.   update Employees set Zip = EmployeeID / 400 + 1 go update statistics Employees with fullscan go  Let’s execute the query serially with MAXDOP 1. --Example provided by www.sqlworkshops.com --Execute query with uneven Zip code distribution --Serially with MAXDOP 1 set statistics time on go declare @EmployeeID int, @EmployeeName varchar(48),@zip int select @EmployeeName = e.EmployeeName, @zip = e.Zip from Employees e       inner join #FireDrill fd on (e.Zip = fd.Zip)       order by e.Zip option (maxdop 1) go   The query took 751 ms to complete.  The execution plan shows the 77816 KB of memory was granted while the estimated rows were 784707.  No Sort Warnings in SQL Server Profiler.   Now let’s execute the query in parallel with MAXDOP 0. --Example provided by www.sqlworkshops.com --Execute query with uneven Zip code distribution --In parallel with MAXDOP 0 set statistics time on go declare @EmployeeID int, @EmployeeName varchar(48),@zip int select @EmployeeName = e.EmployeeName, @zip = e.Zip from Employees e       inner join #FireDrill fd on (e.Zip = fd.Zip)       order by e.Zip option (maxdop 0) go The query took 661 ms to complete.  The execution plan shows the 79360 KB of memory was granted while the estimated rows were 784707.  Sort properties shows the rows are evenly distributed over the 4 threads. No Sort Warnings in SQL Server Profiler.    Intermediate Summary: When employees were distributed unevenly, concentrated on 1 Zip code, parallel sort spilled while serial sort performed well without spilling to tempdb. When the employees were distributed evenly across all Zip codes, parallel sort and serial sort did not spill to tempdb. This shows uneven data distribution may affect the performance of some parallel queries negatively. For detailed discussion of memory allocation, refer to webcasts available at www.sqlworkshops.com/webcasts.     Some of you might conclude from the above execution times that parallel query is not faster even when there is no spill. Below you can see when we are joining limited amount of Zip codes, parallel query will be fasted since it can use Bitmap Filtering.   Let’s update the Employees table with 49 out of 50 employees located in Zip code 2001. update Employees set Zip = EmployeeID / 400 + 1 where EmployeeID % 50 = 1 update Employees set Zip = 2001 where EmployeeID % 50 != 1 go update statistics Employees with fullscan go  Let’s create the temporary table #FireDrill with limited Zip codes. drop table #FireDrill go create table #FireDrill (Zip int primary key) insert into #FireDrill select distinct Zip       from Employees where Zip between 1800 and 2001 update statistics #FireDrill with fullscan go  Let’s execute the query serially with MAXDOP 1. --Example provided by www.sqlworkshops.com --Execute query with uneven Zip code distribution --Serially with MAXDOP 1 set statistics time on go declare @EmployeeID int, @EmployeeName varchar(48),@zip int select @EmployeeName = e.EmployeeName, @zip = e.Zip from Employees e       inner join #FireDrill fd on (e.Zip = fd.Zip)       order by e.Zip option (maxdop 1) go The query took 989 ms to complete.  The execution plan shows the 77816 KB of memory was granted while the estimated rows were 785594. No Sort Warnings in SQL Server Profiler.  Now let’s execute the query in parallel with MAXDOP 0. --Example provided by www.sqlworkshops.com --Execute query with uneven Zip code distribution --In parallel with MAXDOP 0 set statistics time on go declare @EmployeeID int, @EmployeeName varchar(48),@zip int select @EmployeeName = e.EmployeeName, @zip = e.Zip from Employees e       inner join #FireDrill fd on (e.Zip = fd.Zip)       order by e.Zip option (maxdop 0) go The query took 1799 ms to complete.  The execution plan shows the 79360 KB of memory was granted while the estimated rows were 785594.  Sort Warnings in SQL Server Profiler.    The estimated number of rows between serial and parallel plan are the same. The parallel plan has slightly more memory granted due to additional overhead.  Intermediate Summary: The reason for the higher duration with parallel plan even with limited amount of Zip codes was sort spill. This is due to uneven distribution of employees over Zip codes, especially concentration of 49 out of 50 employees in Zip code 2001.   Now let’s update the Employees table and distribute employees evenly across all Zip codes. update Employees set Zip = EmployeeID / 400 + 1 go update statistics Employees with fullscan go Let’s execute the query serially with MAXDOP 1. --Example provided by www.sqlworkshops.com --Execute query with uneven Zip code distribution --Serially with MAXDOP 1 set statistics time on go declare @EmployeeID int, @EmployeeName varchar(48),@zip int select @EmployeeName = e.EmployeeName, @zip = e.Zip from Employees e       inner join #FireDrill fd on (e.Zip = fd.Zip)       order by e.Zip option (maxdop 1) go The query took 250  ms to complete.  The execution plan shows the 9016 KB of memory was granted while the estimated rows were 79973.8.  No Sort Warnings in SQL Server Profiler.  Now let’s execute the query in parallel with MAXDOP 0.  --Example provided by www.sqlworkshops.com --Execute query with uneven Zip code distribution --In parallel with MAXDOP 0 set statistics time on go declare @EmployeeID int, @EmployeeName varchar(48),@zip int select @EmployeeName = e.EmployeeName, @zip = e.Zip from Employees e       inner join #FireDrill fd on (e.Zip = fd.Zip)       order by e.Zip option (maxdop 0) go The query took 85 ms to complete.  The execution plan shows the 13152 KB of memory was granted while the estimated rows were 784707.  No Sort Warnings in SQL Server Profiler.    Here you see, parallel query is much faster than serial query since SQL Server is using Bitmap Filtering to eliminate rows before the hash join.   Parallel queries are very good for performance, but in some cases it can hinder performance. If one identifies the reason for these hindrances, then it is possible to get the best out of parallelism. I covered many aspects of monitoring and tuning parallel queries in webcasts (www.sqlworkshops.com/webcasts) and articles (www.sqlworkshops.com/articles). I suggest you to watch the webcasts and read the articles to better understand how to identify and tune parallel query performance issues.   Summary: One has to avoid sort spill over tempdb and the chances of spills are higher when a query executes in parallel with uneven data distribution. Parallel query brings its own advantage, reduced elapsed time and reduced work with Bitmap Filtering. So it is important to understand how to avoid spills over tempdb and when to execute a query in parallel.   I explain these concepts with detailed examples in my webcasts (www.sqlworkshops.com/webcasts), I recommend you to watch them. The best way to learn is to practice. To create the above tables and reproduce the behavior, join the mailing list at www.sqlworkshops.com/ml and I will send you the relevant SQL Scripts.   Register for the upcoming 3 Day Level 400 Microsoft SQL Server 2008 and SQL Server 2005 Performance Monitoring & Tuning Hands-on Workshop in London, United Kingdom during March 15-17, 2011, click here to register / Microsoft UK TechNet.These are hands-on workshops with a maximum of 12 participants and not lectures. For consulting engagements click here.   Disclaimer and copyright information:This article refers to organizations and products that may be the trademarks or registered trademarks of their various owners. Copyright of this article belongs to R Meyyappan / www.sqlworkshops.com. You may freely use the ideas and concepts discussed in this article with acknowledgement (www.sqlworkshops.com), but you may not claim any of it as your own work. This article is for informational purposes only; you use any of the suggestions given here entirely at your own risk.   Register for the upcoming 3 Day Level 400 Microsoft SQL Server 2008 and SQL Server 2005 Performance Monitoring & Tuning Hands-on Workshop in London, United Kingdom during March 15-17, 2011, click here to register / Microsoft UK TechNet.These are hands-on workshops with a maximum of 12 participants and not lectures. For consulting engagements click here.   R Meyyappan [email protected] LinkedIn: http://at.linkedin.com/in/rmeyyappan  

  Read the article

• The Beginner’s Guide to Linux Disk Utilities

  - by Zainul Franciscus

  Knowing how to check the condition of your hard disk is useful to determine when to replace your hard disk. In today’s article, we will show you some Linux disk utilities to diagnose the health of your hard disk. Image by Scoobay Latest Features How-To Geek ETC The Complete List of iPad Tips, Tricks, and Tutorials The 50 Best Registry Hacks that Make Windows Better The How-To Geek Holiday Gift Guide (Geeky Stuff We Like) LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology The How-To Geek Guide to Learning Photoshop, Part 8: Filters Improve Digital Photography by Calibrating Your Monitor The Brothers Mario – Epic Gangland Style Mario Brothers Movie Trailer [Video] Score Awesome Games on the Cheap with the Humble Indie Bundle Add a Colorful Christmas Theme to Your Windows 7 Desktop This Windows Hack Changes the Blue Screen of Death to Red Edit Images Quickly in Firefox with Pixlr Grabber Zoho Writer, Sheet, and Show Now Available in Chrome Web Store

  Read the article

• Tracking My Internet Provider Speeds

  - by Scott Weinstein

  Of late, our broadband internet has been feeling sluggish. A call to the company took way more hold-time than I wanted to spend, and it only fixed the problem for a short while. Thus a perfect opportunity to play with some new tech to solve a problem, in this case, documenting a systemic issue from a service provider. The goal – a log a internet speeds, taken say every 15 min. Recording ping time, upload speed, download speed, and local LAN usage.   The solution A WCF service to measure speeds Internet speed was measured via speedtest.net LAN usage was measured by querying my router for packets received and sent A SQL express instance to persist the data A PowerShell script to invoke the WCF service – launched by Windows’ Task Scheduler An OData WCF Data Service to allow me to read the data MS PowerPivot to show a nice viz (scratch that, the beta expired) LinqPad to get the data, export it to excel Tableau Public to show the viz     Powered by Tableau

  Read the article

• .co.uk targeted for google.co.uk .com targeted for google.com

  - by Higgs Boson

  We've had a website running on a .co.uk domain for some years, this domain is listed in the SERPS for our brand on both google.co.uk and google.com. We get little traffic from anywhere other than the UK because the website is targeted at the UK market with specific UK keywords. This is great, however we recently purchased the .com domain with the intention of producing a second version of the website targeted to the United States with US specific keywords i.e. targeting and moving in to the US marketplace. We have used Google webmaster tools to set the geographic target for the .com domain to be the US. I think I was expecting ONLY the .com site to show up when searching google.com and only the .co.uk site to show up when searching google.co.uk. However when we search google.com for our 'brand' the .co.uk site is listed in the SERPS. We would prefer the .com to appear in the SERPS on google.com. Is there anything we can do?

  Read the article

• How to find and fix performance problems in ORM powered applications

  - by FransBouma

  Once in a while we get requests about how to fix performance problems with our framework. As it comes down to following the same steps and looking into the same things every single time, I decided to write a blogpost about it instead, so more people can learn from this and solve performance problems in their O/R mapper powered applications. In some parts it's focused on LLBLGen Pro but it's also usable for other O/R mapping frameworks, as the vast majority of performance problems in O/R mapper powered applications are not specific for a certain O/R mapper framework. Too often, the developer looks at the wrong part of the application, trying to fix what isn't a problem in that part, and getting frustrated that 'things are so slow with <insert your favorite framework X here>'. I'm in the O/R mapper business for a long time now (almost 10 years, full time) and as it's a small world, we O/R mapper developers know almost all tricks to pull off by now: we all know what to do to make task ABC faster and what compromises (because there are almost always compromises) to deal with if we decide to make ABC faster that way. Some O/R mapper frameworks are faster in X, others in Y, but you can be sure the difference is mainly a result of a compromise some developers are willing to deal with and others aren't. That's why the O/R mapper frameworks on the market today are different in many ways, even though they all fetch and save entities from and to a database. I'm not suggesting there's no room for improvement in today's O/R mapper frameworks, there always is, but it's not a matter of 'the slowness of the application is caused by the O/R mapper' anymore. Perhaps query generation can be optimized a bit here, row materialization can be optimized a bit there, but it's mainly coming down to milliseconds. Still worth it if you're a framework developer, but it's not much compared to the time spend inside databases and in user code: if a complete fetch takes 40ms or 50ms (from call to entity object collection), it won't make a difference for your application as that 10ms difference won't be noticed. That's why it's very important to find the real locations of the problems so developers can fix them properly and don't get frustrated because their quest to get a fast, performing application failed. Performance tuning basics and rules Finding and fixing performance problems in any application is a strict procedure with four prescribed steps: isolate, analyze, interpret and fix, in that order. It's key that you don't skip a step nor make assumptions: these steps help you find the reason of a problem which seems to be there, and how to fix it or leave it as-is. Skipping a step, or when you assume things will be bad/slow without doing analysis will lead to the path of premature optimization and won't actually solve your problems, only create new ones. The most important rule of finding and fixing performance problems in software is that you have to understand what 'performance problem' actually means. Most developers will say "when a piece of software / code is slow, you have a performance problem". But is that actually the case? If I write a Linq query which will aggregate, group and sort 5 million rows from several tables to produce a resultset of 10 rows, it might take more than a couple of milliseconds before that resultset is ready to be consumed by other logic. If I solely look at the Linq query, the code consuming the resultset of the 10 rows and then look at the time it takes to complete the whole procedure, it will appear to me to be slow: all that time taken to produce and consume 10 rows? But if you look closer, if you analyze and interpret the situation, you'll see it does a tremendous amount of work, and in that light it might even be extremely fast. With every performance problem you encounter, always do realize that what you're trying to solve is perhaps not a technical problem at all, but a perception problem. The second most important rule you have to understand is based on the old saying "Penny wise, Pound Foolish": the part which takes e.g. 5% of the total time T for a given task isn't worth optimizing if you have another part which takes a much larger part of the total time T for that same given task. Optimizing parts which are relatively insignificant for the total time taken is not going to bring you better results overall, even if you totally optimize that part away. This is the core reason why analysis of the complete set of application parts which participate in a given task is key to being successful in solving performance problems: No analysis -> no problem -> no solution. One warning up front: hunting for performance will always include making compromises. Fast software can be made maintainable, but if you want to squeeze as much performance out of your software, you will inevitably be faced with the dilemma of compromising one or more from the group {readability, maintainability, features} for the extra performance you think you'll gain. It's then up to you to decide whether it's worth it. In almost all cases it's not. The reason for this is simple: the vast majority of performance problems can be solved by implementing the proper algorithms, the ones with proven Big O-characteristics so you know the performance you'll get plus you know the algorithm will work. The time taken by the algorithm implementing code is inevitable: you already implemented the best algorithm. You might find some optimizations on the technical level but in general these are minor. Let's look at the four steps to see how they guide us through the quest to find and fix performance problems. Isolate The first thing you need to do is to isolate the areas in your application which are assumed to be slow. For example, if your application is a web application and a given page is taking several seconds or even minutes to load, it's a good candidate to check out. It's important to start with the isolate step because it allows you to focus on a single code path per area with a clear begin and end and ignore the rest. The rest of the steps are taken per identified problematic area. Keep in mind that isolation focuses on tasks in an application, not code snippets. A task is something that's started in your application by either another task or the user, or another program, and has a beginning and an end. You can see a task as a piece of functionality offered by your application.  Analyze Once you've determined the problem areas, you have to perform analysis on the code paths of each area, to see where the performance problems occur and which areas are not the problem. This is a multi-layered effort: an application which uses an O/R mapper typically consists of multiple parts: there's likely some kind of interface (web, webservice, windows etc.), a part which controls the interface and business logic, the O/R mapper part and the RDBMS, all connected with either a network or inter-process connections provided by the OS or other means. Each of these parts, including the connectivity plumbing, eat up a part of the total time it takes to complete a task, e.g. load a webpage with all orders of a given customer X. To understand which parts participate in the task / area we're investigating and how much they contribute to the total time taken to complete the task, analysis of each participating task is essential. Start with the code you wrote which starts the task, analyze the code and track the path it follows through your application. What does the code do along the way, verify whether it's correct or not. Analyze whether you have implemented the right algorithms in your code for this particular area. Remember we're looking at one area at a time, which means we're ignoring all other code paths, just the code path of the current problematic area, from begin to end and back. Don't dig in and start optimizing at the code level just yet. We're just analyzing. If your analysis reveals big architectural stupidity, it's perhaps a good idea to rethink the architecture at this point. For the rest, we're analyzing which means we collect data about what could be wrong, for each participating part of the complete application. Reviewing the code you wrote is a good tool to get deeper understanding of what is going on for a given task but ultimately it lacks precision and overview what really happens: humans aren't good code interpreters, computers are. We therefore need to utilize tools to get deeper understanding about which parts contribute how much time to the total task, triggered by which other parts and for example how many times are they called. There are two different kind of tools which are necessary: .NET profilers and O/R mapper / RDBMS profilers. .NET profiling .NET profilers (e.g. dotTrace by JetBrains or Ants by Red Gate software) show exactly which pieces of code are called, how many times they're called, and the time it took to run that piece of code, at the method level and sometimes even at the line level. The .NET profilers are essential tools for understanding whether the time taken to complete a given task / area in your application is consumed by .NET code, where exactly in your code, the path to that code, how many times that code was called by other code and thus reveals where hotspots are located: the areas where a solution can be found. Importantly, they also reveal which areas can be left alone: remember our penny wise pound foolish saying: if a profiler reveals that a group of methods are fast, or don't contribute much to the total time taken for a given task, ignore them. Even if the code in them is perhaps complex and looks like a candidate for optimization: you can work all day on that, it won't matter.  As we're focusing on a single area of the application, it's best to start profiling right before you actually activate the task/area. Most .NET profilers support this by starting the application without starting the profiling procedure just yet. You navigate to the particular part which is slow, start profiling in the profiler, in your application you perform the actions which are considered slow, and afterwards you get a snapshot in the profiler. The snapshot contains the data collected by the profiler during the slow action, so most data is produced by code in the area to investigate. This is important, because it allows you to stay focused on a single area. O/R mapper and RDBMS profiling .NET profilers give you a good insight in the .NET side of things, but not in the RDBMS side of the application. As this article is about O/R mapper powered applications, we're also looking at databases, and the software making it possible to consume the database in your application: the O/R mapper. To understand which parts of the O/R mapper and database participate how much to the total time taken for task T, we need different tools. There are two kind of tools focusing on O/R mappers and database performance profiling: O/R mapper profilers and RDBMS profilers. For O/R mapper profilers, you can look at LLBLGen Prof by hibernating rhinos or the Linq to Sql/LLBLGen Pro profiler by Huagati. Hibernating rhinos also have profilers for other O/R mappers like NHibernate (NHProf) and Entity Framework (EFProf) and work the same as LLBLGen Prof. For RDBMS profilers, you have to look whether the RDBMS vendor has a profiler. For example for SQL Server, the profiler is shipped with SQL Server, for Oracle it's build into the RDBMS, however there are also 3rd party tools. Which tool you're using isn't really important, what's important is that you get insight in which queries are executed during the task / area we're currently focused on and how long they took. Here, the O/R mapper profilers have an advantage as they collect the time it took to execute the query from the application's perspective so they also collect the time it took to transport data across the network. This is important because a query which returns a massive resultset or a resultset with large blob/clob/ntext/image fields takes more time to get transported across the network than a small resultset and a database profiler doesn't take this into account most of the time. Another tool to use in this case, which is more low level and not all O/R mappers support it (though LLBLGen Pro and NHibernate as well do) is tracing: most O/R mappers offer some form of tracing or logging system which you can use to collect the SQL generated and executed and often also other activity behind the scenes. While tracing can produce a tremendous amount of data in some cases, it also gives insight in what's going on. Interpret After we've completed the analysis step it's time to look at the data we've collected. We've done code reviews to see whether we've done anything stupid and which parts actually take place and if the proper algorithms have been implemented. We've done .NET profiling to see which parts are choke points and how much time they contribute to the total time taken to complete the task we're investigating. We've performed O/R mapper profiling and RDBMS profiling to see which queries were executed during the task, how many queries were generated and executed and how long they took to complete, including network transportation. All this data reveals two things: which parts are big contributors to the total time taken and which parts are irrelevant. Both aspects are very important. The parts which are irrelevant (i.e. don't contribute significantly to the total time taken) can be ignored from now on, we won't look at them. The parts which contribute a lot to the total time taken are important to look at. We now have to first look at the .NET profiler results, to see whether the time taken is consumed in our own code, in .NET framework code, in the O/R mapper itself or somewhere else. For example if most of the time is consumed by DbCommand.ExecuteReader, the time it took to complete the task is depending on the time the data is fetched from the database. If there was just 1 query executed, according to tracing or O/R mapper profilers / RDBMS profilers, check whether that query is optimal, uses indexes or has to deal with a lot of data. Interpret means that you follow the path from begin to end through the data collected and determine where, along the path, the most time is contributed. It also means that you have to check whether this was expected or is totally unexpected. My previous example of the 10 row resultset of a query which groups millions of rows will likely reveal that a long time is spend inside the database and almost no time is spend in the .NET code, meaning the RDBMS part contributes the most to the total time taken, the rest is compared to that time, irrelevant. Considering the vastness of the source data set, it's expected this will take some time. However, does it need tweaking? Perhaps all possible tweaks are already in place. In the interpret step you then have to decide that further action in this area is necessary or not, based on what the analysis results show: if the analysis results were unexpected and in the area where the most time is contributed to the total time taken is room for improvement, action should be taken. If not, you can only accept the situation and move on. In all cases, document your decision together with the analysis you've done. If you decide that the perceived performance problem is actually expected due to the nature of the task performed, it's essential that in the future when someone else looks at the application and starts asking questions you can answer them properly and new analysis is only necessary if situations changed. Fix After interpreting the analysis results you've concluded that some areas need adjustment. This is the fix step: you're actively correcting the performance problem with proper action targeted at the real cause. In many cases related to O/R mapper powered applications it means you'll use different features of the O/R mapper to achieve the same goal, or apply optimizations at the RDBMS level. It could also mean you apply caching inside your application (compromise memory consumption over performance) to avoid unnecessary re-querying data and re-consuming the results. After applying a change, it's key you re-do the analysis and interpretation steps: compare the results and expectations with what you had before, to see whether your actions had any effect or whether it moved the problem to a different part of the application. Don't fall into the trap to do partly analysis: do the full analysis again: .NET profiling and O/R mapper / RDBMS profiling. It might very well be that the changes you've made make one part faster but another part significantly slower, in such a way that the overall problem hasn't changed at all. Performance tuning is dealing with compromises and making choices: to use one feature over the other, to accept a higher memory footprint, to go away from the strict-OO path and execute queries directly onto the RDBMS, these are choices and compromises which will cross your path if you want to fix performance problems with respect to O/R mappers or data-access and databases in general. In most cases it's not a big issue: alternatives are often good choices too and the compromises aren't that hard to deal with. What is important is that you document why you made a choice, a compromise: which analysis data, which interpretation led you to the choice made. This is key for good maintainability in the years to come. Most common performance problems with O/R mappers Below is an incomplete list of common performance problems related to data-access / O/R mappers / RDBMS code. It will help you with fixing the hotspots you found in the interpretation step. SELECT N+1: (Lazy-loading specific). Lazy loading triggered performance bottlenecks. Consider a list of Orders bound to a grid. You have a Field mapped onto a related field in Order, Customer.CompanyName. Showing this column in the grid will make the grid fetch (indirectly) for each row the Customer row. This means you'll get for the single list not 1 query (for the orders) but 1+(the number of orders shown) queries. To solve this: use eager loading using a prefetch path to fetch the customers with the orders. SELECT N+1 is easy to spot with an O/R mapper profiler or RDBMS profiler: if you see a lot of identical queries executed at once, you have this problem. Prefetch paths using many path nodes or sorting, or limiting. Eager loading problem. Prefetch paths can help with performance, but as 1 query is fetched per node, it can be the number of data fetched in a child node is bigger than you think. Also consider that data in every node is merged on the client within the parent. This is fast, but it also can take some time if you fetch massive amounts of entities. If you keep fetches small, you can use tuning parameters like the ParameterizedPrefetchPathThreshold setting to get more optimal queries. Deep inheritance hierarchies of type Target Per Entity/Type. If you use inheritance of type Target per Entity / Type (each type in the inheritance hierarchy is mapped onto its own table/view), fetches will join subtype- and supertype tables in many cases, which can lead to a lot of performance problems if the hierarchy has many types. With this problem, keep inheritance to a minimum if possible, or switch to a hierarchy of type Target Per Hierarchy, which means all entities in the inheritance hierarchy are mapped onto the same table/view. Of course this has its own set of drawbacks, but it's a compromise you might want to take. Fetching massive amounts of data by fetching large lists of entities. LLBLGen Pro supports paging (and limiting the # of rows returned), which is often key to process through large sets of data. Use paging on the RDBMS if possible (so a query is executed which returns only the rows in the page requested). When using paging in a web application, be sure that you switch server-side paging on on the datasourcecontrol used. In this case, paging on the grid alone is not enough: this can lead to fetching a lot of data which is then loaded into the grid and paged there. Keep note that analyzing queries for paging could lead to the false assumption that paging doesn't occur, e.g. when the query contains a field of type ntext/image/clob/blob and DISTINCT can't be applied while it should have (e.g. due to a join): the datareader will do DISTINCT filtering on the client. this is a little slower but it does perform paging functionality on the data-reader so it won't fetch all rows even if the query suggests it does. Fetch massive amounts of data because blob/clob/ntext/image fields aren't excluded. LLBLGen Pro supports field exclusion for queries. You can exclude fields (also in prefetch paths) per query to avoid fetching all fields of an entity, e.g. when you don't need them for the logic consuming the resultset. Excluding fields can greatly reduce the amount of time spend on data-transport across the network. Use this optimization if you see that there's a big difference between query execution time on the RDBMS and the time reported by the .NET profiler for the ExecuteReader method call. Doing client-side aggregates/scalar calculations by consuming a lot of data. If possible, try to formulate a scalar query or group by query using the projection system or GetScalar functionality of LLBLGen Pro to do data consumption on the RDBMS server. It's far more efficient to process data on the RDBMS server than to first load it all in memory, then traverse the data in-memory to calculate a value. Using .ToList() constructs inside linq queries. It might be you use .ToList() somewhere in a Linq query which makes the query be run partially in-memory. Example: var q = from c in metaData.Customers.ToList() where c.Country=="Norway" select c; This will actually fetch all customers in-memory and do an in-memory filtering, as the linq query is defined on an IEnumerable<T>, and not on the IQueryable<T>. Linq is nice, but it can often be a bit unclear where some parts of a Linq query might run. Fetching all entities to delete into memory first. To delete a set of entities it's rather inefficient to first fetch them all into memory and then delete them one by one. It's more efficient to execute a DELETE FROM ... WHERE query on the database directly to delete the entities in one go. LLBLGen Pro supports this feature, and so do some other O/R mappers. It's not always possible to do this operation in the context of an O/R mapper however: if an O/R mapper relies on a cache, these kind of operations are likely not supported because they make it impossible to track whether an entity is actually removed from the DB and thus can be removed from the cache. Fetching all entities to update with an expression into memory first. Similar to the previous point: it is more efficient to update a set of entities directly with a single UPDATE query using an expression instead of fetching the entities into memory first and then updating the entities in a loop, and afterwards saving them. It might however be a compromise you don't want to take as it is working around the idea of having an object graph in memory which is manipulated and instead makes the code fully aware there's a RDBMS somewhere. Conclusion Performance tuning is almost always about compromises and making choices. It's also about knowing where to look and how the systems in play behave and should behave. The four steps I provided should help you stay focused on the real problem and lead you towards the solution. Knowing how to optimally use the systems participating in your own code (.NET framework, O/R mapper, RDBMS, network/services) is key for success as well as knowing what's going on inside the application you built. I hope you'll find this guide useful in tracking down performance problems and dealing with them in a useful way.  

  Read the article

• Custom Binding Part 2: creating a Basic REST service using CUSTOM Binding

  In this article, I am going to show you how we could create a basic WCF REST service using custom binding.

  Read the article

• Software Architecture and Software Architecture Evaluation

  How many of us have worked at places where the concept of software architecture was ridiculed for wasting time and money? Even more ridiculous to them was the concept of evaluating software architecture. I think the next time that I am in this situation again, and I hope that I never am I will have to push for this methodology in the software development life cycle. I have spent way too many hours/days/months/years working poorly architected systems or systems that were just built ADHOC. This in software development must stop. I can understand why systems get like this due to overzealous sales staff, demanding management that wants everything yesterday, and project managers asking if things are done yet before the project has even started. But seriously, some time must be spent designing the applications that we write along with evaluating the architecture so that it will integrate will within the existing systems of an origination. If placed in this situation again, I will strive to gain buying from key players within the business, for example: Senior Software Engineers\Developers, Software Architects, Project Managers, Software Quality Assurance, Technical Services, Operations, and Finance in order for this idea to succeed with upper management. In order to convince these key players I will have to show them the benefits of architecture and even more benefits of evaluating software architecture on a system wide level. Benefits of Software Architecture Evaluation Places Stakeholders in the Same Room to Communicate Ensures Delivery of Detailed Quality Goals Prioritizes Conflicting Goals Requires Clear Explication Improves the Quality of Documentation Discovers Opportunities for Cross-Project Reuse Improves Architecture Practices Once I had key player buy in then and only then would I approach upper management about my plan regarding implementing the concept of software architecture and using evaluation to ensure that the software being designed is the proper architecture for the project. In addition to the benefits listed above I would also show upper management how much time is being wasted by not doing these evaluations. For example, if project X cost us Y amount, then why do we have several implementations in various forms of X and how much money and time could we have saved if we just reused the existing code base to give each system the same functionality that was already created? After this, I would mention what would happen if we had 50 instances of this situation? Then I would show them how the software architecture evaluation process would have prevented this and that the optimization could have leveraged its existing code base to increase the speed and quality of its development. References:Carnegie Mellon Software Engineering Institute (2011). Architecture Tradeoff Analysis Method from http://www.sei.cmu.edu/architecture/tools/evaluate/atam.cfm

  Read the article

• How to configure a zone cluster on Solaris Cluster 4.0

  - by JuergenS

  This is a short overview on how to configure a zone cluster on Solaris Cluster 4.0. This is a little bit different as in Solaris Cluster 3.2/3.3 because Solaris Cluster 4.0 is only running on Solaris 11. The name of the zone cluster must be unique throughout the global Solaris Cluster and must be configured on a global Solaris Cluster. Please read all the requirements for zone cluster in Solaris Cluster Software Installation Guide for SC4.0. For Solaris Cluster 3.2/3.3 please refer to my previous blog Configuration steps to create a zone cluster in Solaris Cluster 3.2/3.3. A. Configure the zone cluster into the already running global clusterCheck if zone cluster can be created # cluster show-netprops to change number of zone clusters use # cluster set-netprops -p num_zoneclusters=12 Note: 12 zone clusters is the default, values can be customized! Create config file (zc1config) for zone cluster setup e.g: Configure zone cluster # clzc configure -f zc1config zc1 Note: If not using the config file the configuration can also be done manually # clzc configure zc1 Check zone configuration # clzc export zc1 Verify zone cluster # clzc verify zc1 Note: The following message is a notice and comes up on several clzc commands Waiting for zone verify commands to complete on all the nodes of the zone cluster "zc1"... Install the zone cluster # clzc install zc1 Note: Monitor the consoles of the global zone to see how the install proceed! (The output is different on the nodes) It's very important that all global cluster nodes have installed the same set of ha-cluster packages! Boot the zone cluster # clzc boot zc1 Login into non-global-zones of zone cluster zc1 on all nodes and finish Solaris installation. # zlogin -C zc1 Check status of zone cluster # clzc status zc1 Login into non-global-zones of zone cluster zc1 and configure the shell environment for root (for PATH: /usr/cluster/bin, for MANPATH: /usr/cluster/man) # zlogin -C zc1 If using additional name service configure /etc/nsswitch.conf of zone cluster non-global zones. hosts: cluster files netmasks: cluster files Configure /etc/inet/hosts of the zone cluster zones Enter all the logical hosts of non-global zones B. Add resource groups and resources to zone cluster Create a resource group in zone cluster # clrg create -n <zone-hostname-node1>,<zone-hostname-node2> app-rg Note1: Use command # cluster status for zone cluster resource group overview. Note2: You can also run all commands for zone cluster in global cluster by adding the option -Z to the command. e.g: # clrg create -Z zc1 -n <zone-hostname-node1>,<zone-hostname-node2> app-rg Set up the logical host resource for zone cluster In the global zone do: # clzc configure zc1 clzc:zc1 add net clzc:zc1:net set address=<zone-logicalhost-ip> clzc:zc1:net end clzc:zc1 commit clzc:zc1 exit Note: Check that logical host is in /etc/hosts file In zone cluster do: # clrslh create -g app-rg -h <zone-logicalhost> <zone-logicalhost>-rs Set up storage resource for zone cluster Register HAStoragePlus # clrt register SUNW.HAStoragePlus Example1) ZFS storage pool In the global zone do: Configure zpool eg: # zpool create <zdata> mirror cXtXdX cXtXdX and # clzc configure zc1 clzc:zc1 add dataset clzc:zc1:dataset set name=zdata clzc:zc1:dataset end clzc:zc1 verify clzc:zc1 commit clzc:zc1 exit Check setup with # clzc show -v zc1 In the zone cluster do: # clrs create -g app-rg -t SUNW.HAStoragePlus -p zpools=zdata app-hasp-rs Example2) HA filesystem In the global zone do: Configure SVM diskset and SVM devices. and # clzc configure zc1 clzc:zc1 add fs clzc:zc1:fs set dir=/data clzc:zc1:fs set special=/dev/md/datads/dsk/d0 clzc:zc1:fs set raw=/dev/md/datads/rdsk/d0 clzc:zc1:fs set type=ufs clzc:zc1:fs add options [logging] clzc:zc1:fs end clzc:zc1 verify clzc:zc1 commit clzc:zc1 exit Check setup with # clzc show -v zc1 In the zone cluster do: # clrs create -g app-rg -t SUNW.HAStoragePlus -p FilesystemMountPoints=/data app-hasp-rs Example3) Global filesystem as loopback file system In the global zone configure global filesystem and it to /etc/vfstab on all global nodes e.g.: /dev/md/datads/dsk/d0 /dev/md/datads/dsk/d0 /global/fs ufs 2 yes global,logging and # clzc configure zc1 clzc:zc1 add fs clzc:zc1:fs set dir=/zone/fs (zc-lofs-mountpoint) clzc:zc1:fs set special=/global/fs (globalcluster-mountpoint) clzc:zc1:fs set type=lofs clzc:zc1:fs end clzc:zc1 verify clzc:zc1 commit clzc:zc1 exit Check setup with # clzc show -v zc1 In the zone cluster do: (Create scalable rg if not already done) # clrg create -p desired_primaries=2 -p maximum_primaries=2 app-scal-rg # clrs create -g app-scal-rg -t SUNW.HAStoragePlus -p FilesystemMountPoints=/zone/fs hasp-rs More details of adding storage available in the Installation Guide for zone cluster Switch resource group and resources online in the zone cluster # clrg online -eM app-rg # clrg online -eM app-scal-rg Test: Switch of the resource group in the zone cluster # clrg switch -n zonehost2 app-rg # clrg switch -n zonehost2 app-scal-rg Add supported dataservice to zone cluster Documentation for SC4.0 is available here Example output: Appendix: To delete a zone cluster do: # clrg delete -Z zc1 -F + Note: Zone cluster uninstall can only be done if all resource groups are removed in the zone cluster. The command 'clrg delete -F +' can be used in zone cluster to delete the resource groups recursively. # clzc halt zc1 # clzc uninstall zc1 Note: If clzc command is not successful to uninstall the zone, then run 'zoneadm -z zc1 uninstall -F' on the nodes where zc1 is configured # clzc delete zc1

  Read the article

• Troubleshooting High-CPU Utilization for SQL Server

  - by Susantha Bathige

  The objective of this FAQ is to outline the basic steps in troubleshooting high CPU utilization on  a server hosting a SQL Server instance. The first and the most common step if you suspect high CPU utilization (or are alerted for it) is to login to the physical server and check the Windows Task Manager. The Performance tab will show the high utilization as shown below: Next, we need to determine which process is responsible for the high CPU consumption. The Processes tab of the Task Manager will show this information: Note that to see all processes you should select Show processes from all user. In this case, SQL Server (sqlserver.exe) is consuming 99% of the CPU (a normal benchmark for max CPU utilization is about 50-60%). Next we examine the scheduler data. Scheduler is a component of SQLOS which evenly distributes load amongst CPUs. The query below returns the important columns for CPU troubleshooting. Note – if your server is under severe stress and you are unable to login to SSMS, you can use another machine’s SSMS to login to the server through DAC – Dedicated Administrator Connection (see http://msdn.microsoft.com/en-us/library/ms189595.aspx for details on using DAC) SELECT scheduler_id ,cpu_id ,status ,runnable_tasks_count ,active_workers_count ,load_factor ,yield_count FROM sys.dm_os_schedulers WHERE scheduler_id See below for the BOL definitions for the above columns. scheduler_id – ID of the scheduler. All schedulers that are used to run regular queries have ID numbers less than 1048576. Those schedulers that have IDs greater than or equal to 1048576 are used internally by SQL Server, such as the dedicated administrator connection scheduler. cpu_id – ID of the CPU with which this scheduler is associated. status – Indicates the status of the scheduler. runnable_tasks_count – Number of workers, with tasks assigned to them that are waiting to be scheduled on the runnable queue. active_workers_count – Number of workers that are active. An active worker is never preemptive, must have an associated task, and is either running, runnable, or suspended. current_tasks_count - Number of current tasks that are associated with this scheduler. load_factor – Internal value that indicates the perceived load on this scheduler. yield_count – Internal value that is used to indicate progress on this scheduler.                                                                 Now to interpret the above data. There are four schedulers and each assigned to a different CPU. All the CPUs are ready to accept user queries as they all are ONLINE. There are 294 active tasks in the output as per the current_tasks_count column. This count indicates how many activities currently associated with the schedulers. When a  task is complete, this number is decremented. The 294 is quite a high figure and indicates all four schedulers are extremely busy. When a task is enqueued, the load_factor  value is incremented. This value is used to determine whether a new task should be put on this scheduler or another scheduler. The new task will be allocated to less loaded scheduler by SQLOS. The very high value of this column indicates all the schedulers have a high load. There are 268 runnable tasks which mean all these tasks are assigned a worker and waiting to be scheduled on the runnable queue.   The next step is  to identify which queries are demanding a lot of CPU time. The below query is useful for this purpose (note, in its current form,  it only shows the top 10 records). SELECT TOP 10 st.text  ,st.dbid  ,st.objectid  ,qs.total_worker_time  ,qs.last_worker_time  ,qp.query_plan FROM sys.dm_exec_query_stats qs CROSS APPLY sys.dm_exec_sql_text(qs.sql_handle) st CROSS APPLY sys.dm_exec_query_plan(qs.plan_handle) qp ORDER BY qs.total_worker_time DESC This query as total_worker_time as the measure of CPU load and is in descending order of the  total_worker_time to show the most expensive queries and their plans at the top:      Note the BOL definitions for the important columns: total_worker_time - Total amount of CPU time, in microseconds, that was consumed by executions of this plan since it was compiled. last_worker_time - CPU time, in microseconds, that was consumed the last time the plan was executed.   I re-ran the same query again after few seconds and was returned the below output. After few seconds the SP dbo.TestProc1 is shown in fourth place and once again the last_worker_time is the highest. This means the procedure TestProc1 consumes a CPU time continuously each time it executes.      In this case, the primary cause for high CPU utilization was a stored procedure. You can view the execution plan by clicking on query_plan column to investigate why this is causing a high CPU load. I have used SQL Server 2008 (SP1) to test all the queries used in this article.

  Read the article

• CodePlex Daily Summary for Thursday, October 24, 2013

  CodePlex Daily Summary for Thursday, October 24, 2013Popular ReleasesX-tee.NET: X-tee.NET 1.0.4: Few code generation bug fixes.VsTortoise - a TortoiseSVN add-in for Microsoft Visual Studio: VsTortoise Build 32 Beta: Note: This release does not work with custom VsTortoise toolbars. These get removed every time when you shutdown Visual Studio. (#7940) This release has been tested with Visual Studio 2008, 2010, 2012 and 2013, using TortoiseSVN 1.6, 1.7 and 1.8. It should also still work with Visual Studio 2005, but I couldn't find anyone to test it in VS2005. Build 32 (beta) changelogNew: Added Visual Studio 2013 support New: Added Visual Studio 2012 support New: Added SVN 1.8 support New: Added 'Ch...ABCat: ABCat v.2.0.1a: ?????????? ???????? ? ?????????? ?????? ???? ??? Win7. ????????? ?????? ????????? ?? ???????. ????? ?????, ???? ????? ???????? ????????? ?????????? ????????? "?? ??????? ????? ???????????? ?????????? ??????...", ?? ?????????? ??????? ? ?????????? ?????? Microsoft SQL Ce ?? ????????? ??????: http://www.microsoft.com/en-us/download/details.aspx?id=17876. ???????? ?????? x64 ??? x86 ? ??????????? ?? ?????? ???????????? ???????. ??? ??????? ????????? ?? ?????????? ?????? Entity Framework, ? ???? ...NB_Store - Free DotNetNuke Ecommerce Catalog Module: NB_Store v2.3.8 Rel3: vv2.3.8 Rel3 updates the version number in the ManagerMenuDefault.xml. Simply update the version setting in the Back Office to 02.03.08 if you have already installed Rel2. v2.3.8 Is now DNN6 and DNN7 compatible NOTE: NB_Store v2.3.8 is NOT compatible with DNN5. SOURCE CODE : https://github.com/leedavi/NB_Store (Source code has been moved to GitHub, due to issues with codeplex SVN and the inability to move easily to GIT on codeplex)patterns & practices: Data Access Guidance: Data Access Guidance 2013: This is the 2013 release of Data Access Guidance. The documentation for this RI is also available on MSDN: Data Access for Highly-Scalable Solutions: Using SQL, NoSQL, and Polyglot Persistence: http://msdn.microsoft.com/en-us/library/dn271399.aspxMedia Companion: Media Companion MC3.584b: IMDB changes fixed. Fixed* mc_com.exe - Fixed to using new profile entries. * Movie - fixed rename movie and folder if use foldername selected. * Movie - Alt Edit Movie, trailer url check if changed and confirm valid. * Movie - Fixed IMDB poster scraping * Movie - Fixed outline and Plot scraping, including removal of Hyperlink's. * Movie Poster refactoring, attempts to catch gdi+ errors Revision HistoryTerrariViewer: TerrariViewer v7.2 [Terraria Inventory Editor]: Added "Check for Update" button Hopefully fixed Windows XP issue You can now backspace in Item stack fieldsDirectXTex texture processing library: October 2013: October 21, 2013 Updated for Visual Studio 2013 and Windows 8.1 SDK RTM PremultiplyAlpha updated with new 'flags' parameter and to use sRGB correct blending Fixed colorspace conversion issue with DirectCompute compressor when compressing for BC7 SRGBSimple Injector: Simple Injector v2.3.6: This patch releases fixes one bug concerning resolving open generic types that contain nested generic type arguments. Nested generic types were handled incorrectly in certain cases. This affects RegisterOpenGeneric and RegisterDecorator. (work item 20332)Virtual Wifi Hotspot for Windows 7 & 8: Virtual Router Plus 2.6.0: Virtual Router Plus 2.6.0Fast YouTube Downloader: Fast YouTube Downloader 2.3.0: Fast YouTube DownloaderMagick.NET: Magick.NET 6.8.7.101: Magick.NET linked with ImageMagick 6.8.7.1. Breaking changes: - Renamed Matrix classes: MatrixColor = ColorMatrix and MatrixConvolve = ConvolveMatrix. - Renamed Depth method with Channels parameter to BitDepth and changed the other method into a property.VidCoder: 1.5.9 Beta: Added Rip DVD and Rip Blu-ray AutoPlay actions for Windows: now you can have VidCoder start up and scan a disc when you insert it. Go to Start -> AutoPlay to set it up. Added error message for Windows XP users rather than letting it crash. Removed "quality" preset from list for QSV as it currently doesn't offer much improvement. Changed installer to ignore version number when copying files over. Should reduce the chances of a bug from me forgetting to increment a version number. Fixed ...MSBuild Extension Pack: October 2013: Release Blog Post The MSBuild Extension Pack October 2013 release provides a collection of over 480 MSBuild tasks. A high level summary of what the tasks currently cover includes the following: System Items: Active Directory, Certificates, COM+, Console, Date and Time, Drives, Environment Variables, Event Logs, Files and Folders, FTP, GAC, Network, Performance Counters, Registry, Services, Sound Code: Assemblies, AsyncExec, CAB Files, Code Signing, DynamicExecute, File Detokenisation, GUI...VG-Ripper & PG-Ripper: VG-Ripper 2.9.49: changes NEW: Added Support for "ImageTeam.org links NEW: Added Support for "ImgNext.com" links NEW: Added Support for "HostUrImage.com" links NEW: Added Support for "3XVintage.com" linksmyCollections: Version 2.8.7.0: New in this version : Added Public Rating Added Collection Number Added Order by Collection Number Improved XBMC integrations Play on music item will now launch default player. Settings are now saved in database. Tooltip now display sort information. Fix Issue with Stars on card view. Fix Bug with PDF Export. Fix Bug with technical information's. Fix HotMovies Provider. Improved Performance on Save. Bug FixingMoreTerra (Terraria World Viewer): MoreTerra 1.11.3.1: Release 1.11.3.1 ================ = New Features = ================ Added markers for Copper Cache, Silver Cache and the Enchanted Sword. ============= = Bug Fixes = ============= Use Official Colors now no longer tries to change the Draw Wires option instead. World reading was breaking for people with a stock 1.2 Terraria version. Changed world name reading so it does not crash the program if you load MoreTerra while Terraria is saving the world. =================== = Feature Removal = =...patterns & practices - Windows Azure Guidance: Cloud Design Patterns: 1st drop of Cloud Design Patterns project. It contains 14 patterns with 6 related guidance.Player Framework by Microsoft: Player Framework for Windows and WP (v1.3): Includes all changes in v1.3 beta 1 and v1.3 beta 2 Support for Windows 8.1 RTM and VS2013 RTM Xaml: New property: AutoLoadPluginTypes to help control which stock plugins are loaded by default (requires AutoLoadPlugins = true). Support for SystemMediaTransportControls on Windows 8.1 JS: Support for visual markers in the timeline. JS: Support for markers collection and markerreached event. JS: New ChaptersPlugin to automatically populate timeline with chapter tracks. JS: Audio an...Json.NET: Json.NET 5.0 Release 8: Fix - Fixed not writing string quotes when QuoteName is falseNew ProjectsActive shape models for .net: Library to find Facial critical points (contour, nose, eyes, mouth) based on active shape models(wrapper for code.google.com/p/asmlibrary). Not support 64bit.Benson's Project: The Task1 project in ASP.NET calculates the sum of two numbers entered in two textboxes and give the output by label when the button "calculate sum" is clicked.cassan: asp.net mvc 4.5 build boostrap3 websiteCoreRG: This project is a Free GNU, its to fast development.Fractals Explorer: A Windows Phone 7 application for exploring a simple collection of fractals.GingerFight: Some test gameGirapong: Girapong is a game for Windows Phone that consist of an original approach to handle the classical sort of games like Pong, using the accelerometer of the phone.Headlight: -KeyWielder: Simple token generatorMDIContainer: MDIContainer extends WPF to support MDI. It displays your user control as window in a container.MocuGame Library: The MocuGame Library is a set of JavaScript classes made for handling every part of making an HTML5-based game, from audio, to graphics, to input.multi: Make creating multi machine environments simple. MvvmCrystalTool: Library for easy work with MVVM pattern in WP8PeerBlock For Android: PeerBlock For Android lets you control who your phone 'talks to' on the Internet. By selecting appropriate lists of 'known bad' computers, you can block...Pescar2013-Shop-Kristo-Giselle-Grecia: Tp para presentarlo el 10/10 PHP to Dynamics CRM 2011 Online: Connect you PHP webSite to Dynamics CRM 2011 Online throw WebServices. You can: - Create Entities - Update Entities - Delete Entities - Use Fetch QueriesProductive Production: Core functionality for a system to manage the entry of production in a manufacturing environment. The intent will be to provide some base functionality and intProject Of DreamTeam: Space Invaders windows phone / windowsTVShows-EF5: Proyecto básico de integración con diferentes tecnologías.Validation Engine: Validation Engine for WinForms. Engine provides powerful, flexible and easy to use rule based validation for your application. DevExpress and Net.Spring ready.WCF Events: Vis Stud 2010 C# WCF events Demo Solution??? ?, ??? ?.: ??? ?, ??? ?.

  Read the article

• CodePlex Daily Summary for Friday, December 31, 2010

  CodePlex Daily Summary for Friday, December 31, 2010Popular ReleasesFree Silverlight & WPF Chart Control - Visifire: Visifire SL and WPF Charts v3.6.6 Released: Hi, Today we are releasing final version of Visifire, v3.6.6 with the following new feature: * TextDecorations property is implemented in Title for Chart. * TitleTextDecorations property is implemented in Axis. * MinPointHeight property is now applicable for Column and Bar Charts. Also this release includes few bug fixes: * ToolTipText property of DataSeries was not getting applied from Style. * Chart threw exception if IndicatorEnabled property was set to true and Too...Windows Weibo all in one for Sina Sohu and QQ: WeiBee V0.1: WeiBee is an all in one Twitter tool, which can update Wei Bo at the same time for websites. It intends to support t.sohu.com, t.sina.com.cn and t.qq.com.cn. If you have WeiBo at SOHU, SINA and QQ, you can try this tool to help you save time to open all the webpages to update your status. For any business opportunity, such as put advertise on China Twitter market, and to build a custom WeiBo tool, please reach my email box qq1800@gmail.com My official WeiBo is http://mediaroom.t.sohu.comStyleCop Compliant Visual Studio Code Snippets: Visual Studio Code Snippets - January 2011: StyleCop Compliant Visual Studio Code Snippets Visual Studio 2010 provides C# developers with 38 code snippets, enhancing developer productivty and increasing the consistency of the code. Within this project the original code snippets have been refactored to provide StyleCop compliant versions of the original code snippets while also adding many new code snippets. Within the January 2011 release you'll find 82 code snippets to make you more productive and the code you write more consistent!...WPF Application Framework (WAF): WPF Application Framework (WAF) 2.0.0.2: Version: 2.0.0.2 (Milestone 2): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requirements .NET Framework 4.0 (The package contains a solution file for Visual Studio 2010) The unit test projects require Visual Studio 2010 Professional Remark The sample applications are using Microsoft’s IoC container MEF. However, the WPF Application Framework (WAF) doesn’t force you to use the same IoC container in your application. You can use ...eCompany: eCompany v0.2.0 Build 63: Version 0.2.0 Build 63: Added Splash screen & about box Added downloading of currencies when eCompany launched for the first time (must close any bug caused by no currency rate existing) Added corp creation when eCompany launched for the first time (for now, you didn't need to edit the company.xml file manually) You just need to decompress file "eCompany v0.2.0.63.zip" into your current eCompany install directory.SQL Monitor - tracking sql server activities: SQL Monitor 3.0 alpha 8: 1. added truncate table/defrag index/check db functions 2. improved alert 3. fixed problem with alert causing config file corrupted(hopefully)Analysis Services Stored Procedure Project: 1.3.5 Release: This release includes the following fixes and new functionality: Updates to GetCubeLastProcessedDate to work with perspectives Fixes to reports that call Discover functions improving drillthrough functions against perspectives improving ExecuteDrillthroughAndFixColumns logic fixing situation where MDX query calling certain ASSP sprocs which opened external connections caused deadlock to SSAS processing small fix to Partition code when DbColumnName property doesn't exist changes...DocX: DocX v1.0.0.11: Building Examples projectTo build the Examples project, download DocX.dll and add it as a reference to the project. OverviewThis version of DocX contains many bug fixes, it is a serious step towards a stable release. Added1) Unit testing project, 2) Examples project, 3) To many bug fixes to list here, see the source code change list history.Cosmos (C# Open Source Managed Operating System): 71406: This is the second release supporting the full line of Visual Studio 2010 editions. Changes since release 71246 include: Debug info is now stored in a single .cpdb file (which is a Firebird database) Keyboard input works now (using Console.ReadLine) Console colors work (using Console.ForegroundColor and .BackgroundColor)AutoLoL: AutoLoL v1.5.0: Added the all new Masteries Browser which replaces the Quick Open combobox AutoLoL will now attemt to create file associations for mastery (*.lolm) files Each Mastery Build can now contain keywords that the Masteries Browser will use for filtering Changed the way AutoLoL detects if another instance is already running Changed the format of the mastery files to allow more information stored in* Dialogs will now focus the Ok or Cancel button which allows the user to press Return to clo...Paint.NET PSD Plugin: 1.6.0: Handling of layer masks has been greatly improved. Improved reliability. Many PSD files that previously loaded in as garbage will now load in correctly. Parallelized loading. PSD files containing layer masks will load in a bit quicker thanks to the removal of the sequential bottleneck. Hidden layers are no longer made visible on save. Many thanks to the users who helped expose the layer masks problem: Rob Horowitz, M_Lyons10. Please keep sending in those bug reports and PSD repro files!Facebook C# SDK: 4.1.1: From 4.1.1 Release: Authentication bug fix caused by facebook change (error with redirects in Safari) Authenticator fix, always returning true From 4.1.0 Release Lots of bug fixes Removed Dynamic Runtime Language dependencies from non-dynamic platforms. Samples included in release for ASP.NET, MVC, Silverlight, Windows Phone 7, WPF, WinForms, and one Visual Basic Sample Changed internal serialization to use Json.net BREAKING CHANGE: Canvas Session is no longer supported. Use Signed...Catel - WPF and Silverlight MVVM library: 1.0.0: And there it is, the final release of Catel, and it is no longer a beta version!EnhSim: EnhSim 2.2.7 ALPHA: 2.2.7 ALPHAThis release supports WoW patch 4.03a at level 85 To use this release, you must have the Microsoft Visual C++ 2010 Redistributable Package installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=A7B7A05E-6DE6-4D3A-A423-37BF0912DB84 To use the GUI you must have the .NET 4.0 Framework installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992 - Mongoose has bee...Euro for Windows XP: ChangeRegionalSettings 1..0: *Rocket Framework (.Net 4.0): Rocket Framework for Windows V 1.0.0: Architecture is reviewed and adjusted in a way so that I can introduce the Web version and WPF version of this framework next. - Rocket.Core is introduced - Controller button functions revisited and updated - DB is renewed to suite the implemented features - Create New button functionality is changed - Add Question Handling featuresFlickr Wallpaper Rotator (for Windows desktop): Wallpaper Flickr 1.1: Some minor bugfixes (mostly covering when network connection is flakey, so I discovered them all while at my parents' house for Christmas).NoSimplerAccounting: NoSimplerAccounting 6.0: -Fixed a bug in expense category report.NHibernate Mapping Generator: NHibernate Mapping Generator 2.0: Added support for Postgres (Thanks to Angelo)NewLife XCode: XCode v6.5.2010.1223 ????（????v3.5??）: XCode v6.5.2010.1223 ????，??： NewLife.Core ??? NewLife.Net ??? XControl ??? XTemplate ????，??C#?????? XAgent ???? NewLife.CommonEnitty ??????（???，XCode??????） XCode?? ?????????，??????????????????，?????95% XCode v3.5.2009.0714 ??，?v3.5?v6.0???????????????，?????????。v3.5???????????，??????????????。 XCoder ??XTemplate?????????，????????XCode??? XCoder_Src ???????（????XTemplate????），??????????????????New Projects1i2m3i4s5e6r7p: 1i2m3i4s5e6r7pA3 Fashion Web: A complete e-commerce siteAfonsoft Blog - Blog de teste: Blog para teste de desenvolvimento em MySQL ou SQLServer com ASP.NET 3.5AnyGrid for ASP.NET MVC: Which grid component should you use for your ASP.NET MVC project? How about all of them? AnyGrid makes it easy to switch between grid implementations, allowing a single action to, e.g., use two different grids for desktop and mobile views. It also supports DataAnnnotations.BizTalk Map Test Framework: The Map Test Framework makes it easier for BizTalk developers to test their maps. You'll no longer have to maintain a whole bunch of XML files for your tests. The use of template files and xpath queries to perform tests will increase your productivity tremendously.BlogResult.NET: A simple Blogging starter kit using S#harp Architecture. This project was originally course material sample code for an MVC class, but we decided to open source it and make it available to the community.Caro: Code demo caro game.Ecozany Skin for DotNetNuke: This Ecozany package contains three sample skins and a collection of containers for use in your DotNetNuke web sites.Enhanced lookup field: Enhanced lookup field makes it easier for end users to create filters. You'll no longer have to use a custom field or javascript to have a parent child lookup for example. It's developed in C#. - Parent/multiple child lookups - Advanced filters options - Easy to usejobglance: This is job siteMaxLeafWeb_K3: MaxLeafWeb_K3Miage Kart: Projet java M1msystem: MVC. Net web systemNetController: Controle sem teclas de direção, usando acelerômentro e .NET micro Framework.Pencils - A Blog Site framework: Another Blog site frameworkPICTShell: PICT is an efficient way to design test cases and test configurations for software systems. PICT Shell is the GUI for PICT.Portal de Solicitação de Serviços: O Portal de Solicitação de Serviços é uma solução que atende diversas empresas prestadores de serviços. Inicialmente desenvolvido para atender empresa de informática, mas o objetivo é que com a publicação do fonte, ele seja extendido à diversos tipos de prestadoras.Runery: Runery RSPSsCut4s: sCut4sSumacê Jogava Caxangá?: sumace makes it easier for gamers to play. You'll no longer have to play. It's developed in XNA.Supply_Chain_FInance: Supply Chain Finance thrives these years all over the world. In exploring the inner working mechanism ,we can sought to have a way to embed an information system in it. We develop the system to suit the domesticated supply chain finace .TestAmir: ??? ????? ??? ???The Cosmos: School project on a SOA based system (Loan system)Time zone: A c# library for manage time changes for any time zone in the world. Based on olson database.Validate: Validate is a collection of extension methods that let you add validations to any object and display validations in a user/developer friendly format. Its an extremely light weight validation framework with a zero learning curve.Windows Phone 7 Silverlight ListBox with CheckBox Control: A Windows Phone 7 ListBox control, providing CheckBoxes for item selection when in "Choose State" and no CheckBoxes in "Normal State", like the built-in Email app, with nice transition. To switch between states, set the "IsInChooseState" property. The control inherits ListBox.XQSOFT.WF.Designer: this is workflow designerzhanghai: my test project

  Read the article

• The .NET Rocks! Visual Studio 2010 Road Trip

  - by Laila

  Carl Franklin and Richard Campbell, the two .NET Rocks radio show hosts, have decided to set off to 15 cities in the US, between April 19th and May 7th, in their DotNetMobile (a 30 foot RV). What for you'll ask me? Well, to drive around the US, meet up with .NET developers, and show off the latest and greatest in Visual Studio 2010 and .NET 4.0! Each evening, they stop in a city and host a three hour event in front of a 100 to 300 crowd of developers, where Carl is showing off media features in Silverlight 4 and their road trip tracking application, whilst Richard is demo-ing the web performance testing features of VS2010 using his portable server rig. But before they take to the stage, they have a special guest brought in - a rock star from the Visual Studio world - whom they interview for an hour as a .NET Rock episode. So far, they've had - amongst others - Phil Haack, a Program Manager with the ASP.NET team working on ASP.NET MVC, Dan Fernandez, an Evangelism Manager in the Developer and Platform Evangelism team at Microsoft, and Beth Massi, Senior Program Manager on the Visual Studio Community Team at Microsoft. I love the fact that the audience gets a chance to participate, ask questions and have a great laugh, as you can hear in the first episode! Along the way, the .NET Rocks guys are giving away great prizes (including .NET Reflector Pro, ANTS Memory Profiler licenses, and "40" LCD TVs!). Even more out of the ordinary, at each stop on the road trip, one lucky attendee (who entered in the Ride Along competition) gets to jump in the RV with Carl and Richard and ride along with them to the next stop on the roadtrip. How cool is that! Richard told us: "Our first winner in Mountain View was Eric Ziko. I was looking for him to announce that he had won, when he found us and gave us a bottle of scotch he had brought just to say 'thanks for the great show'. We all had a toast from the bottle the next night when he headed back home." Cheeky! There's still space to a few of these events, so if you want to attend, register now, because it's first come first serve. We're grateful to Richard and Carl for giving us the opportunity to sponsor this major .NET event! A unique .NET adventure worth following for sure. Cheers, Laila

  Read the article

• The .NET Rocks! Visual Studio 2010 Road Trip

  Carl Franklin and Richard Campbell, hosts of the .NET Rocks radio show, have decided to set off in their DotNetMobile (a 30 foot RV) to 15 US cities between April 19th and May 7th. What for, you ask? Why, to meet up with .NET developers and show off the latest and greatest in Visual Studio 2010 and .NET 4.0...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Regular Expressions. Remember it, write it, test it.

  - by outcoldman

  I should say that I’m fan of regular expressions. Whenever I see the problem, which I can solve with Regex, I felt a burning desire to do it and going to write new test for new regex. Previously I had installed SharpDevelop Studio just for good regular expression tool in it (Why VS doesn’t have one?). But now I’m a little wiser, and for each Regex I write a separate test. I find it difficult to remember the syntax of regular expressions (I don’t write them very often); I always forget which character is responsible for the beginning of the line, etc. So I use external small and easy articles like this “Regular expressions - An introduction”. Now I want to show you little samples of regular expressions and want to show you how to test these samples. Read more... (redirect to http://outcoldman.ru)

  Read the article

• SQL SERVER – Repair a SQL Server Database Using a Transaction Log Explorer

  - by Pinal Dave

  In this blog, I’ll show how to use ApexSQL Log, a SQL Server transaction log viewer. You can download it for free, install, and play along. But first, let’s describe some disaster recovery scenarios where it’s useful. About SQL Server disaster recovery Along with database development and administration, you must work on a good recovery plan. Disasters do happen and no one’s immune. What you can do is take all actions needed to be ready for a disaster and go through it with minimal data loss and downtime. Besides creating a recovery plan, it’s necessary to have a list of steps that will be executed when a disaster occurs and to test them before a disaster. This way, you’ll know that the plan is good and viable. Testing can also be used as training for all team members, so they can all understand and execute it when the time comes. It will show how much time is needed to have your servers fully functional again and how much data you can lose in a real-life situation. If these don’t meet recovery-time and recovery-point objectives, the plan needs to be improved. Keep in mind that all major changes in environment configuration, business strategy, and recovery objectives require a new recovery plan testing, as these changes most probably induce a recovery plan changing and tweaking. What is a good SQL Server disaster recovery plan? A good SQL Server disaster recovery strategy starts with planning SQL Server database backups. An efficient strategy is to create a full database backup periodically. Between two successive full database backups, you can create differential database backups. It is essential is to create transaction log backups regularly between full database backups. Keep in mind that transaction log backups can be created only on databases in the full recovery model. In other words, a simple, but efficient backup strategy would be a full database backup every night, a transaction log backup every hour, or every 15 minutes. The frequency depends on how much data you can afford to lose and how busy the database is. Another option, instead of creating a full database backup every night, is to create a full database backup once a week (e.g. on Friday at midnight) and differential database backup every night until next Friday when you will create a full database backup again. Once you create your SQL Server database backup strategy, schedule the backups. You can do that easily using SQL Server maintenance plans. Why are transaction logs important? Transaction log backups contain transactions executed on a SQL Server database. They provide enough information to undo and redo the transactions and roll back or forward the database to a point in time. In SQL Server disaster recovery situations, transaction logs enable to repair a SQL Server database and bring it to the state before the disaster. Be aware that even with regular backups, there will be some data missing. These are the transactions made between the last transaction log backup and the time of the disaster. In some situations, to repair your SQL Server database it’s not necessary to re-create the database from its last backup. The database might still be online and all you need to do is roll back several transactions, such as wrong update, insert, or delete. The restore to a point in time feature is available in SQL Server, but for large databases, it is very time-consuming, as SQL Server first restores a full database backup, and then restores transaction log backups, one after another, up to the recovery point. During that time, the database is unavailable. This is where a SQL Server transaction log viewer can help. For optimal recovery, besides having a database in the full recovery model, it’s important that you haven’t manually truncated the online transaction log. This ensures that all transactions made after the last transaction log backup are still in the online transaction log. All you have to do is read and replay them. How to read a SQL Server transaction log? SQL Server doesn’t provide an option to read transaction logs. There are several SQL Server commands and functions that read the content of a transaction log file (fn_dblog, fn_dump_dblog, and DBCC PAGE), but they are undocumented. They require T-SQL knowledge, return a large number of not easy to read and understand columns, sometimes in binary or hexadecimal format. Another challenge is reading UPDATE statements, as it’s necessary to match it to a value in the MDF file. When you finally read the transactions executed, you have to create a script for it. How to easily repair a SQL database? The easiest solution is to use a transaction log reader that will not only read the transactions in the transaction log files, but also automatically create scripts for the read transactions. In the following example, I will show how to use ApexSQL Log to repair a SQL database after a crash. If a database has crashed and both MDF and LDF files are lost, you have to rely on the full database backup and all subsequent transaction log backups. In another scenario, the MDF file is lost, but the LDF file is available. First, restore the last full database backup on SQL Server using SQL Server Management Studio. I’ll name it Restored_AW2014. Then, start ApexSQL Log It will automatically detect all local servers. If not, click the icon right to the Server drop-down list, or just type in the SQL Server instance name. Select the Windows or SQL Server authentication type and select the Restored_AW2014 database from the database drop-down list. When all options are set, click Next. ApexSQL Log will show the online transaction log file. Now, click Add and add all transaction log backups created after the full database backup I used to restore the database. In case you don’t have transaction log backups, but the LDF file hasn’t been lost during the SQL Server disaster, add it using Add.   To repair a SQL database to a point in time, ApexSQL Log needs to read and replay all the transactions in the transaction log backups (or the LDF file saved after the disaster). That’s why I selected the Whole transaction log option in the Filter setup. ApexSQL Log offers a range of various filters, which are useful when you need to read just specific transactions. You can filter transactions by the time of the transactions, operation type (e.g. to read only data inserts), table name, SQL Server login that made the transaction, etc. In this scenario, to repair a SQL database, I’ll check all filters and make sure that all transactions are included. In the Operations tab, select all schema operations (DDL). If you omit these, only the data changes will be read so if there were any schema changes, such as a new function created, or an existing table modified, they will be ignored and database will not be properly repaired. The data repair for modified tables will fail. In the Tables tab, I’ll make sure all tables are selected. I will uncheck the Show operations on dropped tables option, to reduce the number of transactions. Click Next. ApexSQL Log offers three options. Select Open results in grid, to get a user-friendly presentation of the transactions. As you can see, details are shown for every transaction, including the old and new values for updated columns, which are clearly highlighted. Now, select them all and then create a redo script by clicking the Create redo script icon in the menu.   For a large number of transactions and in a critical situation, when acting fast is a must, I recommend using the Export results to file option. It will save some time, as the transactions will be directly scripted into a redo file, without showing them in the grid first. Select Generate reconstruction (REDO) script , change the output path if you want, and click Finish. After the redo T-SQL script is created, ApexSQL Log shows the redo script summary: The third option will create a command line statement for a batch file that you can use to schedule execution, which is not really applicable when you repair a SQL database, but quite useful in daily auditing scenarios. To repair your SQL database, all you have to do is execute the generated redo script using an integrated developer environment tool such as SQL Server Management Studio or any other, against the restored database. You can find more information about how to read SQL Server transaction logs and repair a SQL database on ApexSQL Solution center. There are solutions for various situations when data needs to be recovered, restored, or transactions rolled back. Reference: Pinal Dave (http://blog.sqlauthority.com)Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL

  Read the article

• Jamie Oliver&rsquo;s Food Revolution from a parent&rsquo;s perspective

  This is the first generation of kids expected to live a shorter life than you. Or...you guys can start kicking some ass. Jamie Oliver. Theres been a show running on ABC recentlyabout 6 episodes. Its called Jamie Olivers Food Revolution. It appears to have been taped during the fall of 2009 in Huntington, West Virginia (which evidently was selected because of high child obesity data). The show absolutely has a bit of Hollywood, a ton of editing, but I dont think anyone can doubt Jamies (and the...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

< Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >