Search Results

Search found 23220 results on 929 pages for 'default constraint'.

Page 263/929 | < Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >

• Ubuntu 12.04 + Wifi not working

  - by user171154

  i'm having problems connecting over wireless. At the moment, I'm using wicd. It seems to get stuck on "Verifying AP association...". Without wicd I can get the connection up and ping the Net - but if I take eth0 down (ifconfig eth0 down), my wireless goes away too (same result if I unplug the wire instead). wicd is the only way I can bring eth0 back (which is the main reason I'm using it) - ifconfig eth0 and/or ifup eth0 do not re-enable the connection (I just discovered it leaves out the gateway. Adding the gateway back in re-enables the connection including wifi; I didn't want to delete the info about wicd above in case it gives someone an idea.) Doing it manually, despite the errors (which it would be nice to also resolve) - allows me to ping the outside world: ifup wlan0 ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument ssh stop/waiting ssh start/running, process 17336 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=43 time=48.8 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=43 time=47.9 ms 64 bytes from 8.8.8.8: icmp_req=3 ttl=43 time=48.7 ms 64 bytes from 8.8.8.8: icmp_req=4 ttl=43 time=53.2 ms --- 8.8.8.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 47.975/49.711/53.235/2.063 ms # iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TPLINK" Mode:Managed Frequency:2.427 GHz Access Point: 64:66:xx:xx:xx:22 Bit Rate=108 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=70/70 Signal level=-39 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:3 Missed beacon:0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: f0:7d:68:c1:b4:13 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-67-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:dfbf0000-dfbfffff ip route default via 192.168.0.1 dev eth0 default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 (For the record, I have no idea what the 169.254.0.0 address is doing there.) uname -a 3.2.0-67-generic-pae #101-Ubuntu SMP Tue Jul 15 18:04:54 UTC 2014 i686 i686 i386 GNU/Linux lshw -C network *-network description: Ethernet interface product: NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 01 serial: 00:11:11:59:fc:09 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5751-v3.23a ip=192.168.0.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:dfcf0000-dfcfffff *-network description: Wireless interface product: AR5418 Wireless Network Adapter [AR5008E 802.11(a)bgn] (PCI-Express) vendor: Qualcomm Atheros physical id: 0 /etc/network/interfaces # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback source /etc/network/interfaces.eth0 source /etc/network/interfaces.wlan0 /etc/network/interfaces.eth0 #Main Interface auto eth0 iface eth0 inet static address 192.168.0.102 netmask 255.255.255.0 gateway 192.168.0.1 /etc/network/interfaces.wlan0 auto wlan0 iface wlan0 inet static address 192.168.0.12 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 netmask 255.255.255.0 wpa-driver wext wpa-ssid TPLINK wpa-ap-scan 1 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk dca1badb5fd4e9axxx4xxdaaxxfa91xx610bxx6a7d57ef67af9809dxx6af42e39 /etc/wpa_supplicant.conf ctrl_interface=/var/run/wpa_supplicant network={ ssid="TPLINK" psk="my password" key_mgmt=WPA-PSK proto=RSN pairwise=CCMP group=CCMP } ifdown eth0 ifdown: interface eth0 not configured ifconfig eth0 Link encap:Ethernet HWaddr 00:11:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:213690 errors:0 dropped:0 overruns:0 frame:0 TX packets:155266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:220057808 (220.0 MB) TX bytes:21137696 (21.1 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196412 errors:0 dropped:0 overruns:0 frame:0 TX packets:196412 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270697 (153.2 MB) TX bytes:153270697 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11335 errors:0 dropped:0 overruns:0 frame:0 TX packets:7287 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2563290 (2.5 MB) TX bytes:855746 (855.7 KB) ifconfig eth0 down ifconfig eth0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:192 (192.0 B) TX bytes:94 (94.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196418 errors:0 dropped:0 overruns:0 frame:0 TX packets:196418 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270871 (153.2 MB) TX bytes:153270871 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11359 errors:0 dropped:0 overruns:0 frame:0 TX packets:7293 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2565482 (2.5 MB) TX bytes:856363 (856.3 KB) ip route default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. --- 8.8.8.8 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3024ms ping -I eth0 -c 3 router PING router (192.168.0.1) from 192.168.0.102 eth0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2015ms ping -I wlan0 -c 3 router PING router (192.168.0.1) from 192.168.0.12 wlan0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2014ms Let me know if you need more info. Thank you in advance.

  Read the article

• Is there a way of listing files for a directory if it contains index.html?

  - by fredley

  On my server (over which I have little control), directories are listed by default, so for mysite.com/images I get: Index of /images Parent Directory BirdsAreHere.png CanYouSpot-AdBlank.jpg etc. Is putting an index.html in that directory enough to prevent people listing the files, or is there still a way of getting at that list? Is it the same for my web root directory (mysite.com)?

  Read the article

• Creating Multiple Queries for Running Objects

  - by edurdias

  Running Objects combines the power of LINQ with Metadata definition to let you leverage multiples perspectives of your queries of objects. By default, RO brings all the objects in natural order of insertion and including all the visible properties of your class. In this post, we will understand how the QueryAttribute class is structured and how to make use of it. The QueryAttribute class This class is the responsible to specify all the possible perspectives of a list of objects. In other words, is...(read more)

  Read the article

• Using IIS Logs for Performance Testing with Visual Studio

  - by Tarun Arora

  In this blog post I’ll show you how you can play back the IIS Logs in Visual Studio to automatically generate the web performance tests. You can also download the sample solution I am demo-ing in the blog post. Introduction Performance testing is as important for new websites as it is for evolving websites. If you already have your website running in production you could mine the information available in IIS logs to analyse the dense zones (most used pages) and performance test those pages rather than wasting time testing & tuning the least used pages in your application. What are IIS Logs To help with server use and analysis, IIS is integrated with several types of log files. These log file formats provide information on a range of websites and specific statistics, including Internet Protocol (IP) addresses, user information and site visits as well as dates, times and queries. If you are using IIS 7 and above you will find the log files in the following directory C:\Interpub\Logs\ Walkthrough 1. Download and Install Log Parser from the Microsoft download Centre. You should see the LogParser.dll in the install folder, the default install location is C:\Program Files (x86)\Log Parser 2.2. LogParser.dll gives us a library to query the iis log files programmatically. By the way if you haven’t used Log Parser in the past, it is a is a powerful, versatile tool that provides universal query access to text-based data such as log files, XML files and CSV files, as well as key data sources on the Windows operating system such as the Event Log, the Registry, the file system, and Active Directory. More details… 2. Create a new test project in Visual Studio. Let’s call it IISLogsToWebPerfTestDemo.   3.  Delete the UnitTest1.cs class that gets created by default. Right click the solution and add a project of type class library, name it, IISLogsToWebPerfTestEngine. Delete the default class Program.cs that gets created with the project. 4. Under the IISLogsToWebPerfTestEngine project add a reference to Microsoft.VisualStudio.QualityTools.WebTestFramework – c:\Program Files (x86)\Microsoft Visual Studio 10.0\Common7\IDE\PublicAssemblies\Microsoft.VisualStudio.QualityTools.WebTestFramework.dll LogParser also called MSUtil - c:\users\tarora\documents\visual studio 2010\Projects\IisLogsToWebPerfTest\IisLogsToWebPerfTestEngine\obj\Debug\Interop.MSUtil.dll 5. Right click IISLogsToWebPerfTestEngine project and add a new classes – IISLogReader.cs The IISLogReader class queries the iis logs using the log parser. using System; using System.Collections.Generic; using System.Text; using MSUtil; using LogQuery = MSUtil.LogQueryClassClass; using IISLogInputFormat = MSUtil.COMIISW3CInputContextClassClass; using LogRecordSet = MSUtil.ILogRecordset; using Microsoft.VisualStudio.TestTools.WebTesting; using System.Diagnostics; namespace IisLogsToWebPerfTestEngine { // By making use of log parser it is possible to query the iis log using select queries public class IISLogReader { private string _iisLogPath; public IISLogReader(string iisLogPath) { _iisLogPath = iisLogPath; } public IEnumerable<WebTestRequest> GetRequests() { LogQuery logQuery = new LogQuery(); IISLogInputFormat iisInputFormat = new IISLogInputFormat(); // currently these columns give us suffient information to construct the web test requests string query = @"SELECT s-ip, s-port, cs-method, cs-uri-stem, cs-uri-query FROM " + _iisLogPath; LogRecordSet recordSet = logQuery.Execute(query, iisInputFormat); // Apply a bit of transformation while (!recordSet.atEnd()) { ILogRecord record = recordSet.getRecord(); if (record.getValueEx("cs-method").ToString() == "GET") { string server = record.getValueEx("s-ip").ToString(); string path = record.getValueEx("cs-uri-stem").ToString(); string querystring = record.getValueEx("cs-uri-query").ToString(); StringBuilder urlBuilder = new StringBuilder(); urlBuilder.Append("http://"); urlBuilder.Append(server); urlBuilder.Append(path); if (!String.IsNullOrEmpty(querystring)) { urlBuilder.Append("?"); urlBuilder.Append(querystring); } // You could make substitutions by introducing parameterized web tests. WebTestRequest request = new WebTestRequest(urlBuilder.ToString()); Debug.WriteLine(request.UrlWithQueryString); yield return request; } recordSet.moveNext(); } Console.WriteLine(" That's it! Closing the reader"); recordSet.close(); } } }   6. Connect the dots by adding the project reference ‘IisLogsToWebPerfTestEngine’ to ‘IisLogsToWebPerfTest’. Right click the ‘IisLogsToWebPerfTest’ project and add a new class ‘WebTest1Coded.cs’ The WebTest1Coded.cs inherits from the WebTest class. By overriding the GetRequestMethod we can inject the log files to the IISLogReader class which uses Log parser to query the log file and extract the web requests to generate the web test request which is yielded back for play back when the test is run. namespace IisLogsToWebPerfTest { using System; using System.Collections.Generic; using System.Text; using Microsoft.VisualStudio.TestTools.WebTesting; using Microsoft.VisualStudio.TestTools.WebTesting.Rules; using IisLogsToWebPerfTestEngine; // This class is a coded web performance test implementation, that simply passes // the path of the iis logs to the IisLogReader class which does the heavy // lifting of reading the contents of the log file and converting them to tests. // You could have multiple such classes that inherit from WebTest and implement // GetRequestEnumerator Method and pass differnt log files for different tests. public class WebTest1Coded : WebTest { public WebTest1Coded() { this.PreAuthenticate = true; } public override IEnumerator<WebTestRequest> GetRequestEnumerator() { // substitute the highlighted path with the path of the iis log file IISLogReader reader = new IISLogReader(@"C:\Demo\iisLog1.log"); foreach (WebTestRequest request in reader.GetRequests()) { yield return request; } } } }   7. Its time to fire the test off and see the iis log playback as a web performance test. From the Test menu choose Test View Window you should be able to see the WebTest1Coded test show up. Highlight the test and press Run selection (you can also debug the test in case you face any failures during test execution). 8. Optionally you can create a Load Test by keeping ‘WebTest1Coded’ as the base test. Conclusion You have just helped your testing team, you now have become the coolest developer in your organization! Jokes apart, log parser and web performance test together allow you to save a lot of time by not having to worry about what to test or even worrying about how to record the test. If you haven’t already, download the solution from here. You can take this to the next level by using LogParser to extract the log files as part of an end of day batch to a database. See the usage trends by user this solution over a longer term and have your tests consume the web requests now stored in the database to generate the web performance tests. If you like the post, don’t forget to share … Keep RocKiNg!

  Read the article

• Right click is disabled on Desktop

  - by RameshKatkam

  I installed elementary OS and e17 on my Ubuntu 12.04 from ppas. After logout and login, right click on desktop is not working in gnome and unity but working in file manger.When I login into Pantheon session, I don't find an option to open Home folder and my login display manager theme is also changed.I want to get back to default Ubuntu login theme.Can i change the login theme with simple-lightdm manager. I dont want to mess up my system.Please hemp me how to fix these.

  Read the article

• HTG Explains: Do You Really Need to Safely Remove USB Sticks?

  - by Chris Hoffman

  You’ve probably heard that you always need to use the Safely Remove Hardware icon before unplugging a USB device. However, there’s also a good chance that you’ve unplugged a USB device without using this option and everything worked fine. Windows itself tells you that you don’t need to use the Safely Remove Hardware option if you use certain settings – the default settings – but the advice Windows provides is misleading. How to Use an Xbox 360 Controller On Your Windows PC Download the Official How-To Geek Trivia App for Windows 8 How to Banish Duplicate Photos with VisiPic

  Read the article

• Thinkpad brightness steps error using FN+Home/End

  - by petermolnar

  I've met the following problem: normally my T400 (Lenovo Thinkpad) has 16 steps of brightness, and Windows utilizes it correctly. After a fresh install & minor tweaks Mint 12 (which is based on 11.10 Ubuntu) I only had 6 steps which was way to few. Listing /sys/class/backlight showed 3 entried. I removed the acpi-tools package, one of the disapperared - and I now have 10 steps! Therefore I think if I can reduce the entries to 1 I'm going to have 16 steps, since the stepping will be 1 instead of 2 (or 3). /sys/class/backlight/ intel_backlight -> ../../devices/pci0000:00/0000:00:02.0/drm/card0/card0-LVDS-1/intel_backlight thinkpad_screen -> ../../devices/virtual/backlight/thinkpad_screen The problem is that I'm unable to trace back what are the configs / daemons / kernel options triggers these two. More strangely, I discovered a strange behaviour. I monitored watch -n1 "cat /sys/class/backlight/thinkpad_screen/actual_brightness" and watch -n1 "cat /sys/class/backlight/intel_backlight/actual_brightness" while changing the brightness with FN+home/end combinations from max to min. The outcome is the following: brighness intel thinkpad --------- ----- -------- MAX 2408475 7 | 1955115 5 | 1435640 3 | 1246740 1 | 1086175 0 | 1010615 6 | 859495 4 | 689485 2 v 481695 0 MIN 217235 0 brighness intel thinkpad --------- ----- -------- MIN 217235 0 | 481695 2 | 689485 4 | 859495 6 | 1010615 7 | 1086175 1 | 1246740 3 | 1435640 5 v 1955115 7 MAX 2408475 0 When stepping from MIN to MAX, there's no difference between the last 2 steps. Also, the OSD icon (Cinnamon desktop, default theme) goes from full to min in 4 steps and from full to min once again in 4 steps. So... it seems that the intel entry is working correctly, showing correct values. The thinkpad entry however twists the things and even showing incorrect values. Does anyone have any idea how to get rid of the thinkpad entry? System data: Linux Mint 12 3.0.0-16 kernel Lenovo ThinkPad T400 Cinnamon 1.4 desktop For any additional info, please tell me what do you need. EDIT I'm sorry, I forgot to mention, I added acpi_backlight=vendor to GRUB cmdline as well, this is the result of the semi-better working than the default.

  Read the article

• Empathy not showing in memenu

  - by dadexix86

  I just installed 12.10 and noticed that, even if I added more than one account to Online Accounts and I'm actually using empathy to chat, it is not present in Messaging Menu or in any other point of the tray. This means that if i close it, it remains open but unaccessbile and I have to start it again from dash. How can i integrate it in messaging menu (shouldn't this be the default?) or, at least, make it showing me a tray icon?

  Read the article

• Avoiding connection timeouts on first connection to LocalDB edition of SQL Server Express

  - by Greg Low

  When you first make a connection to the new LocalDB edition of SQL Server Express, the system files, etc. that are required for a new version are spun up. (The system files such as the master database files, etc. end up in C:\Users\<username>\AppData\Local\Microsoft\Microsoft SQL Server Local DB\Instances\LocalDBApp1) That can take a while on a slower machine, so this means that the default connection timeout of 30 seconds (in most client libraries) could be exceeded. To avoid this hit on the...(read more)

  Read the article

• Notifications for Expiring DBSNMP Passwords

  - by Courtney Llamas

  Most user accounts these days have a password profile on them that automatically expires the password after a set number of days.   Depending on your company’s security requirements, this may be as little as 30 days or as long as 365 days, although typically it falls between 60-90 days. For a normal user, this can cause a small interruption in your day as you have to go get your password reset by an admin. When this happens to privileged accounts, such as the DBSNMP account that is responsible for monitoring database availability, it can cause bigger problems. In Oracle Enterprise Manager 12c you may notice the error message “ORA-28002: the password will expire within 5 days” when you connect to a target, or worse you may get “ORA-28001: the password has expired". If you wait too long, your monitoring will fail because the password is locked out. Wouldn’t it be nice if we could get an alert 10 days before our DBSNMP password expired? Thanks to Oracle Enterprise Manager 12c Metric Extensions (ME), you can! See the Oracle Enterprise Manager Cloud Control Administrator’s Guide for more information on Metric Extensions. To create a metric extension, select Enterprise / Monitoring / Metric Extensions, and then click on Create. On the General Properties screen select either Cluster Database or Database Instance, depending on which target you need to monitor.  If you have both RAC and Single instance you may need to create one for each. In this example we will create a Cluster Database metric.  Enter a Name for the ME and a Display Name. Then select SQL for the Adapter.  Adjust the Collection Schedule as desired, for this example we will collect this metric every 1 day. Notice for metric collected every day, we can determine the exact time we want to collect. On the Adapter page, enter the query that you wish to execute.  In this example we will use the query below that specifically checks for the DBSNMP user that is expiring within 10 days. Of course, you can adjust this query to alert for any user that can cause an outage such as an application account or service account such as RMAN. select username, account_status, trunc(expiry_date-sysdate) days_to_expirefrom dba_userswhere username = 'DBSNMP'and expiry_date is not null; The next step is to create the columns to store the data returned from the query.  Click Add and add a column for each of the fields in the same order that data is returned.  The table below will help you complete the column additions. Name Display Name Column Type Value Type Metric Category Unit Username User Name Key String Security AccountStatus Account Status Data String Security DaysToExpire Days Until Expiration Data Number Security Days When creating the DaysToExpire column, you can add a default threshold here for Warning and Critical (say < 10 and 5).  When all columns have been added, click Next. On the Credentials page, you can choose to use the default monitoring credentials or specify new credentials.  We will use the default credentials established for our target (dbsnmp). The next step is to test your Metric Extension.  Click on Add to select a target for testing, then click Select. Now click the button Run Test to execute the test against the selected target(s). We can see in the example below that the Metric Extension has executed and returned a value of 68 days to expire. Click Next to proceed. Review the metric extension in the final screen and click Finish. The metric will be created in Editable status.  Select the metric, click Actions and select Deployable Draft. You can do this once more to move to Published. Finally, we want to apply this metric to a target. When managing many targets, it’s best to add your metric to a template, for details on adding a Metric Extension to a template see the Administrator’s Guide. For this example, we will deploy this to a target directly. Select Actions / Deploy to Targets. Click Add and select the target you wish to deploy to and click Submit.  Once deployment is complete, we can go to the target and view the Metric & Collection Settings to see the new metric and its thresholds.   After some time, you will find the metric has collected and the days to expiration for DBSNMP user can be seen in the All Metrics view.   For metrics collected once per day, you may have to wait up to 24 hours to see the metric and current severity. In the example below, the current severity is Clear (green check) as it is not scheduled to expire within 10 days. To test the notification, we can edit the thresholds for the new metric so they trigger an alert.  Our password expires in 139 days, so we’ll change our Warning to 140 and leave Critical at 5, in our example we also changed the collection time to every 5 minutes.  At the next collection, you’ll find that the current severity changes to a Warning and any related Incident Rules would be triggered to create an Incident or Notification as desired. Now that you get a notification that your DBSNMP passwords is about to expire, you can use OEM Command Line Interface (EM CLI) verb update_db_password to change it at both the database target and the OEM target in one step.  The caveat is you must know the existing password to use the update_db_password command.  To learn more about EM CLI, see the Oracle Enterprise Manager Command Line Interface Guide.  Below is an example of changing the password with the update_db_password verb.  $ ./emcli update_db_password -target_name=emrep -target_type=oracle_database -user_name=dbsnmp -change_at_target=yes -change_all_references=yes Enter value for old_password :Enter value for new_password :Enter value for retype_new_password :Successfully submitted a job to change the password in Enterprise Manager and on the target database: "emrep"Execute "emcli get_jobs -job_id=FA66C1C4D663297FE0437656F20ACC84" to check the status of the job.Search for job name "CHANGE_PWD_JOB_FA66C1C4D662297FE0437656F20ACC84" on the Jobs home page to check job execution details. The subsequent job created will typically run quickly enough that a blackout is not needed, however if you submit a script with many targets to change, your job may run slower so adding a blackout to the script is recommended. $ ./emcli get_jobs -job_id=FA66C1C4D663297FE0437656F20ACC84 Name Type Job ID Execution ID Scheduled Completed TZ Offset Status Status ID Owner Target Type Target Name CHANGE_PWD_JOB_FA66C1C4D662297FE0437656F20ACC84 ChangePassword FA66C1C4D663297FE0437656F20ACC84 FA66C1C4D665297FE0437656F20ACC84 2014-05-28 09:39:12 2014-05-28 09:39:18 GMT-07:00 Succeeded 5 SYSMAN oracle_database emrep After implementing the above Metric Extension and using the EM CLI update_db_password verb, you will be able to stay on top of your DBSNMP password changes without experiencing an unplanned monitoring outage.  

  Read the article

• Banshee for MeeGo

  <b>Aaron Bockover:</b> "After lots of intense work and collaboration, the Netbook profile for MeeGo 1.0 has been released today. As such, I am particularly pleased to announce in conjunction that Banshee is the default and integrated media player for MeeGo."

  Read the article

• How do I publish updates?

  - by Klikini

  A common issue with Unity is the suspend feature, which reboots some computers when resuming. I have figured out how to fix it, tested it, and it works. You change line 11 of /etc/default/grub to: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_sleep=nonvs" I would like to post this as an update for future Ubuntu versions. How do I do this? More info about the changes: Sony Vaio FW350 reboots instead of waking up after sleep/suspend

  Read the article

• Community is Great

  - by GrumpyOldDBA

  I have a great respect for so many who contribute to the community, without them I would often struggle in my role for sure. When "strange events" happen in a busy production environment it can be quite daunting when it seems everyone around is expecting you to have the answer/solution at your finger tips. I'm indebted to Paul White http://sqlblog.com/blogs/paul_white/default.aspx in confirming I'd found a bug and doing all the hard work including raising a connect item https:/...(read more)

  Read the article

• Get rid of the style="border-width:0px" from the Image tag.

  - by webbes

  Sometimes it bothers me that by default the ASP.NET Image control adds a style="border-width:0px" to the rendered image tag even though I never asked for it. You can get rid of it though!...(read more)

  Read the article

• Is there any free host which supports php and mySQL in utf-8? [closed]

  - by Maria Konnou

  Possible Duplicate: How to find web hosting that meets my requirements? Is there any free host which supports php and mySQL queries in utf-8? I've already tried to use x10hosting and 000webhosting, but they don't support utf8 mysql queries (got mojibake). The default encoding of mysql in both sites is latin-1, and you're not able to change that. Is there any other free host that fully supports utf-8?

  Read the article

• Connection Closed and Connect Reset By Peer Errors [on hold]

  - by Alex Pineda

  We're running freebsd + jail, and lighttpd + fastcgi + php_cgi. We changed our domain and all of a sudden we are getting SPORADIC connection closes. We recently changed our subdomain from www to shop but really there have been no other major changes. When I modified lighttpd's server.max-read-idle from default 60 to 5 the connection close message comes much more rapidly however it has not corrected the issue.

  Read the article

• How do I find out which boot loader I have?

  - by binW

  I know Grub is the one installed by default when installing Ubuntu but I am faced with an embedded system running 9.10 Desktop Edition. Following are the contents of lsb-release file ubuntu@ubuntu-desktop:/boot$ cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=9.10 DISTRIB_CODENAME=karmic DISTRIB_DESCRIPTION="Ubuntu 9.10" but this system does not have Grub bootloader and I want to find out which one its using. So any ideas?

  Read the article

• why jamendo is off stores of music player banshee and rhythmbox and how can i add jamendo to the stores?

  - by user49523

  jamendo is open music platform for artists and listers, i know that debian was on jamendo on the stores on rhythmbox by default, and also ubuntu use to have so why is not been there anymore on ubuntu ? is it because of ubuntu one ? and how can i add jamendo to the music players like rhythmbox and banshee ? magnatune store is on rhytmbox plugins bu t not on banshee ? can we expect jamendo to be include on next release , that i am using beta version, of ubuntu 12.04?

  Read the article

• How do I hide my custom Unity panel indicators from another user account on the same machine?

  - by Inkayacu

  I created a second user account on my machine, making it a "standard" user account. When I log into that account, most of the panel indicators I've added in my own administrator user account show up here as well -- but not all of them (e.g., the cpufreq indicator shows up in both accounts, but the multiload indicator does not show up in the second account). I'd like to prevent everything but the default panel indicators from a fresh Ubuntu install showing up in the second user's panel.

  Read the article

• Dual-boot computer won't boot without external hard drive

  - by FrankP

  I have Ubuntu loaded on my external HDD. I tried to unplug the external drive so that this way I could run Windows as the default OS to boot when the computer turns on, but it gives me an error. I need to know how I can make it so that when my computers boots it stops saying Error: no such device: (a whole bunch of numbers and letters) then it says grub rescue>_. If I plug the external HDD in, and I let Ubuntu run the boot process, then it gives me a list of OS's/ HDD's to choose from and Windows 7 is there. The only problem is that I want Windows be my default OS, not the other way around. P.S. I have found that I dislike Ubuntu because I can't even figure out how to install the necessary programs to learn how to start writing Ruby On Rails. So installing it was a waste of my time, in my opinion. Now that I have it on the external hard drive, I will leave it installed though. I just dont want to have to keep that external drive plugged in to my computer all the time. Thank you a ton to whoever can help me! Thank you for the detail'd instructions. I am doing my best to follow you and it makes sense when I read it but, Rescatux is not doing what you said it would. None of the options you said would appear are not there. On my screen there is 4 options when MBR run's none look familiar and when I picked the best possible option based on my educated guesses it said success. I tried to restart my computer and it said Please insert windows recovery disc and hit enter. Problem being I don't have the windows recovery disc. I bought my computer from a local Computer tec and he loads windows on it for you. I have no time to run my compute over to him as sunday is my only day free. I think that I just wrecked my computer in the process of this attempted fix windows refuses to boot now WITH or WITHOUT the HDD. Please help this is getting out of hand

  Read the article

• Compiz with Intel video card not working after upgrade to 11.04

  - by fazi

  After upgrade to ubuntu 11.04 from 10.10 My compiz stop working I have no cube effects and preview files and other compiz stuff. I have intel x4500 (00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) ) glxinfo name of display: :0 display: :0 screen: 0 direct rendering: Yes server glx vendor string: Brian Paul server glx version string: 1.4 Mesa 7.11-devel I have removed compiz, gnome (witch --purge) and install again, nothing works :( Im using default ubuntu desktop (no unity) any idea how can I fix this?:

  Read the article

• LTSP thin client to single user mode

  - by DJC

  Is it possible to boot a LTSP thin client to single user mode? I've updated the default entry under /var/lib/tftpboot/ltsp/i386/pxelinux.cfg to read as follows: - append ro initrd=initrd.img root=/dev/nbd0 init=/sbin/init-ltsp nomodeset quiet splash **single** plymouth:force-splash vt.handoff=7 nbdroot=:ltsp_i386 This kind of works! I see the boot progress to the point where it asks me to either enter the root password or Ctrl+D to bypass. However, the boot process just seems to continue without providing an chance to do either.

  Read the article

• ATI RS690m X1200 proprietary driver installation

  - by fan-dz

  I've installed Ubuntu 11.10 on my emachine e625 AMD64 (TF-20) with an ATI RS690m X1200 graphics card but I didn't have 3D acceleration. The open-source driver works, except for any video effects or acceleration… I've downloaded the driver from ATI and followed the installation instructions and here is the result: Error: ./default_policy.sh does not support version default:v2:x86_64:lib32::none:3.0.0-17-generic; make sure that the version is being correctly set by --iscurrentdistro What did I do wrong?

  Read the article

• My Visual Studio 2010 Setup

  - by Latest Microsoft Blogs

  When I install Visual Studio 2010, I only install the stuff I really need.  It’s easy to just do the “default” install but in my experience I find that not only does it take up additional hard drive space but the installation time is significantly Read More......(read more)

  Read the article

• Stuxnet - how it infects

  - by Kit Ong

  Except from the CNET article.http://news.cnet.com/8301-13772_3-57413329-52/stuxnet-delivered-to-iranian-nuclear-plant-on-thumb-drive/?part=propeller&subj=news&tag=linkvThe Stuxnet worm propagates by exploiting a hole in all versions of Windows in the code that processes shortcut files, ending in ".lnk," according to...[the] Microsoft Malware Protection Center....Merely browsing to the removable media drive using an application that displays shortcut icons, such as Windows Explorer, will run the malware without the user clicking on the icons. The worm infects USB drives or other removable storage devices that are subsequently connected to the infected machine. Those USB drives then infect other machines much like the common cold is spread by infected people sneezing into their hands and then touching door knobs that others are handling.The malware includes a rootkit, which is software designed to hide the fact that a computer has been compromised, and other software that sneaks onto computers by using a digital certificates signed two Taiwanese chip manufacturers that are based in the same industrial complex in Taiwan--RealTek and JMicron, according to Chester Wisniewski, senior security advisor at Sophos.... It is unclear how the digital signatures were acquired by the attacker, but experts believe they were stolen and that the companies were not involved.Once the machine is infected, a Trojan looks to see if the computer it lands on is running Siemens' Simatic WinCC software. The malware then automatically uses a default password that is hard-coded into the software to access the control system's Microsoft SQL database. The Stuxnet worm propagates by exploiting a hole in all versions of Windows in the code that processes shortcut files, ending in ".lnk," according to...[the] Microsoft Malware Protection Center....Merely browsing to the removable media drive using an application that displays shortcut icons, such as Windows Explorer, will run the malware without the user clicking on the icons. The worm infects USB drives or other removable storage devices that are subsequently connected to the infected machine. Those USB drives then infect other machines much like the common cold is spread by infected people sneezing into their hands and then touching door knobs that others are handling.The malware includes a rootkit, which is software designed to hide the fact that a computer has been compromised, and other software that sneaks onto computers by using a digital certificates signed two Taiwanese chip manufacturers that are based in the same industrial complex in Taiwan--RealTek and JMicron, according to Chester Wisniewski, senior security advisor at Sophos.... It is unclear how the digital signatures were acquired by the attacker, but experts believe they were stolen and that the companies were not involved.Once the machine is infected, a Trojan looks to see if the computer it lands on is running Siemens' Simatic WinCC software. The malware then automatically uses a default password that is hard-coded into the software to access the control system's Microsoft SQL database.

  Read the article

< Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >