Search Results

Search found 9366 results on 375 pages for 'common lisp'.

Page 264/375 | < Previous Page | 260 261 262 263 264 265 266 267 268 269 270 271  | Next Page >

• Symantec Endpoint Protection Virus Definitions

  - by Gus Denton

  I have done some Googling but I cannot get a definitive answer certainly not from the Symantec KB. I have a Virtualised Win 2003R2 server 32bit. It has been provisioned to me with Symantec Endpoint Protection 11.0.62xxx CLIENT (not a definitions server) the directory C:\Program Files\Common Files\Symantec Shared\VirusDefs is 750MB IT doesn't contain .tmp directories so it is NOT a corrupt definitions server. IT does contain directories named with a date pattern YYYYMMDD.xxx Some of these folders are 12 months old and I would like to recover the space. The sysmantect forums are full of this stuff but a lot of the postings contain links back to documents that are not specific to End Point Protection Client. It appears that I should be able to delete the older folders and all will be OK. with a service restart however there is a warning about having Live Update Administrator Installed Firstly I have no idea if I have this installed how to I check and secondly can I just ditch these old files and restart ? Regards Gus Denton Learning and Teaching Uni of New South Wales Sydney Australia For those trying to assist me I thankyou. I have followed some instructions found on the Symantec site and assumed that the response from Nixphoe would resolve my issue. It appears that as I am on a provisioned VM from a central IT unit I cannot run the Symantec commands from the Run prompt as my admin creds to get me in. (smc -stop) Basically I need to claw back some Diskspace from the c: drive which is being filed up with WSUS patches and Symantec files. I have managed to delete one symantec cache through the live update control panel and recovered 470Mb I suppose my last question for those more experienced than myself is, can I simply remove say the two oldest virus definition folders without completely foobaring the End Point protection and the server ? Regards Gus

  Read the article

• How do I switch java versions to an earlier version in Fedora 17?

  - by JHutson456

  I just installed Fedora 17. I'm setting up the Android Build Environment and need Java. I downloaded and installed jdk-6u32-linux-amd64.rpm I ran java -version and it spit out the correct version. Well a day or two later i tried my first compile in Fedora 17 and it complained about java and failed. I ran java -version again and low and behold it spits out $ java -version java version "1.7.0_03-icedtea" OpenJDK Runtime Environment (fedora-2.1.fc17.7-x86_64) OpenJDK 64-Bit Server VM (build 22.0-b10, mixed mode) I'm stumped. I mean, i've run the update/upgrade commands since i installed but i didn't think that updated full version revisions... So, I ran alternatives --config java and that only gave me the java 1.7 version. While digging around more I discovered that the recommended version of Java for the build environment is jdk-6u27-linux-x64-rpm.bin so I downloaded that from here: Oracle Download When I ran: sudo sh jdk-6u27-linux-x64-rpm.bin it returned: Unpacking... Checksumming... Extracting... UnZipSFX 5.50 of 17 February 2002, by Info-ZIP ([email protected]). inflating: jdk-6u27-linux-amd64.rpm inflating: sun-javadb-common-10.6.2-1.1.i386.rpm inflating: sun-javadb-core-10.6.2-1.1.i386.rpm inflating: sun-javadb-client-10.6.2-1.1.i386.rpm inflating: sun-javadb-demo-10.6.2-1.1.i386.rpm inflating: sun-javadb-docs-10.6.2-1.1.i386.rpm inflating: sun-javadb-javadoc-10.6.2-1.1.i386.rpm Preparing... ########################################### [100%] package jdk-2000:1.6.0_32-fcs.x86_64 (which is newer than jdk-2000:1.6.0_27-fcs.x86_64) is already installed Done. so now I'm confused. I ran: alternatives --config java again but it's still only returning 1.7 so I don't know what to do.I want to end up with 6u27 as the installed and functional version of the JDK. Thank you.

  Read the article

• TFS 2012 and MS SQL 2008r2

  - by Vadim911

  When I try to call TFS 2012 warehouse control web service (WarehouseControlService.asmx) I got following error: Exception Message: Could not load file or assembly 'Microsoft.AnalysisServices, Version=10.0.0.0, Culture=neutral, PublicKeyToken=89845dcd8080cc91' or one of its dependencies. The system cannot find the file specified. (type FileNotFoundException) Exception Stack Trace:    at Microsoft.TeamFoundation.Warehouse.WarehouseConfigurationService.RebuildOLAPDatabase(TeamFoundationRequestContext requestContext, String olapServerInstanceName, String databaseName, String warehouseServerInstanceName, String warehouseDatabaseName, Int32 translationLCID, Boolean checkAndUpdateJobs)    at Microsoft.TeamFoundation.Warehouse.WarehouseConfigurationService.RebuildOLAPDatabase(TeamFoundationRequestContext requestContext, String olapServerInstanceName, String databaseName, String warehouseServerInstanceName, String warehouseDatabaseName, Int32 translationLCID)    at Microsoft.TeamFoundation.Management.SnapIn.ApplicationTierNode.RebuildReporting(IntPtr hwnd, IRefreshable panel) Inner Exception Details: Exception Message: Could not load file or assembly 'Microsoft.AnalysisServices, Version=11.0.0.0, Culture=neutral, PublicKeyToken=89845dcd8080cc91' or one of its dependencies. The system cannot find the file specified. (type FileNotFoundException) Exception Stack Trace:    at System.Reflection.RuntimeAssembly._nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, RuntimeAssembly locationHint, StackCrawlMark& stackMark, IntPtr pPrivHostBinder, Boolean throwOnFileNotFound, Boolean forIntrospection, Boolean suppressSecurityChecks)    at System.Reflection.RuntimeAssembly.InternalLoadAssemblyName(AssemblyName assemblyRef, Evidence assemblySecurity, RuntimeAssembly reqAssembly, StackCrawlMark& stackMark, IntPtr pPrivHostBinder, Boolean throwOnFileNotFound, Boolean forIntrospection, Boolean suppressSecurityChecks)    at System.Reflection.Assembly.Load(AssemblyName assemblyRef)    at Microsoft.TeamFoundation.Common.Internal.TfsAssemblyResolver.OnAssemblyResolve(Object sender, ResolveEventArgs args)    at System.AppDomain.OnAssemblyResolveEvent(RuntimeAssembly assembly, String assemblyFullName) It is strange because I have installed ms sql connectivity. Is it issue connected with the fact that I try to use tfs 2012 with ms sql 2012? Please advise how to resolve issue networked above.

  Read the article

• If I can take a screen capture of a graphical anomaly, can it still be a hardware issue?

  - by Jay Carr

  I have a strange graphical anomaly going on my iMac right now (green and magenta boxes are appearing sporadically), I'm slowly trying to work through different possibilities but I thought I'd start with the basics: Can a graphical anomaly that I can screen capture still be a hardware issue? I know, it seems really obvious. If it's hardware, it should show up well after the operating system has had it's say. And since the operating system is (I assume) doing the screen capture, it seems like it shouldn't see the anomaly unless the problem is software in nature. But, as I've researched this problem I see a lot of people taking their computers in to service people for hardware issues and Apple then resolving said issue. To further complicate things, I also have Windows 8 installed via bootcamp, and the issues seems to be showing up there as well. Anyway, it feels like it must be a driver issue, since I assume that's what the two OSes have in common, but...I thought I'd come here for some disambiguation. In my case, yes, I can screen capture the anomaly (at least in OSX I can), so I assume it's somehow a software (or driver) issue. But I wanted to double check because the internet is being ambiguous...

  Read the article

• How do you verify a restore?

  - by Nic

  What tool(s) would you use to verify that a restored file structure is whole and complete? My environment is a Windows Server 2008 file server. (We use tape for backup, but that is inconsequential.) I am specifically looking for a tool that will: Record the names of all files and folders below a specified directory Optionally calculate checksums of each file encountered Save this index in a human-readable format Compare the index against restored data and show differences Some background: I recently had to replace the disks in our file server. The upgrade was scheduled to start 36 hours after the most recent full backup, so I created a differential backup. However, it turns out that one of our applications was clearing the archive bit on files saved to the server, so these were not included in the differential backup. I was unaware of this until my users reported some files as missing. Aside from this, are there any other common methods for validating the integrity of a restore? I am frequently told that testing backups by restoring them is the only way to know that backups are working, but how do you deal with the case where it works 99% correctly and the other 1% silently fails?

  Read the article

• Apache is sending php files to my browser instead of parsing

  - by justen doherty

  I have to set up PHP on an existing web host. I have made a virtual host entry, but for some reason Apache is sending the PHP to the browser instead of parsing.. from googling around it looks like it's a problem with the mimetypes, but I'm not an Apache expert by any means, so if anyone could help it would be appreciated... I have the following in my httpd.conf: AddHandler php5-script php DirectoryIndex index.html index.phtml index.php index.phps AddType application/x-httpd-php .phtml AddType application/x-httpd-php .php AddType application/x-httpd-php-source .phps The PHP module is loaded into Apache: /usr/sbin/apachectl -M Loaded Modules: core_module (static) mpm_prefork_module (static) http_module (static) so_module (static) auth_basic_module (shared) auth_digest_module (shared) authn_file_module (shared) authn_alias_module (shared) authn_anon_module (shared) authn_dbm_module (shared) authn_default_module (shared) authz_host_module (shared) authz_user_module (shared) authz_owner_module (shared) authz_groupfile_module (shared) authz_dbm_module (shared) authz_default_module (shared) ldap_module (shared) authnz_ldap_module (shared) include_module (shared) log_config_module (shared) logio_module (shared) env_module (shared) ext_filter_module (shared) mime_magic_module (shared) expires_module (shared) deflate_module (shared) headers_module (shared) usertrack_module (shared) setenvif_module (shared) mime_module (shared) dav_module (shared) status_module (shared) autoindex_module (shared) info_module (shared) dav_fs_module (shared) vhost_alias_module (shared) negotiation_module (shared) dir_module (shared) actions_module (shared) speling_module (shared) userdir_module (shared) alias_module (shared) rewrite_module (shared) proxy_module (shared) proxy_balancer_module (shared) proxy_ftp_module (shared) proxy_http_module (shared) proxy_connect_module (shared) cache_module (shared) suexec_module (shared) disk_cache_module (shared) file_cache_module (shared) mem_cache_module (shared) cgi_module (shared) version_module (shared) fcgid_module (shared) perl_module (shared) php5_module (shared) proxy_ajp_module (shared) ssl_module (shared) And this is my virtual host entry: <VirtualHost 10.16.140.113:80> ServerName viridor-cms.co.uk ServerAlias www.viridor-cms.co.uk UseCanonicalName Off DocumentRoot /var/www/vhosts/viridor-cms.co.uk/httpdocs CustomLog /var/www/vhosts/viridor-cms.co.uk/cms-access_log common ErrorLog /var/www/vhosts/viridor-cms.co.uk/cms-error_log DirectoryIndex index.php index.html <IfModule sapi_apache2.c> php_admin_flag engine on php_admin_flag safe_mode on </IfModule> <IfModule mod_php5.c> php_admin_flag engine on php_admin_flag safe_mode on </IfModule> AddType application/x-httpd-php .php AddType application/x-httpd-php-source .phps </VirtualHost> Please help, my head is so sore from banging it against the table and the wall!

  Read the article

• Installing Linux on an Asus p8z68-m PRO Motherboard

  - by Holland

  Here is a challenge: how is this done? I've tried disabling the ASM1061 controller in the Onboard Devices section, using Wubi, booting from USB (as I don't have a DVD drive, yet), and even booting from RAID/IDE (with AHCI as the default) to do this. Still, no dice. Google shows up virtually nothing related about Linux and this mobo, apart from a people just saying "disable ASMedia" (which, I assume is the ASM1061 controller, as that's all I see - apart from the USB 3.0, which I disabled already) and it hasn't really helped much. Thus, what is wrong here? Edit My problem is that I cannot boot Linux via USB or a simple Windows installer such as Wubi (for Ubuntu). I wind up getting error messages along the lines of write cache failed, along with many other cryptic error messages similar to the following: [ 1400.351374] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled [ 1400.353433] sd 4:0:0:0: [sdb] Asking for cache data failed [ 1400.356601] sd 4:0:0:0: [sdb] Assuming drive cache: write through This seems to be common for Asus P8Z68-M Pro motherboards, with the only notable solution being to "disable ASMedia", which, as I said before, I'm guessing is the ASM1061 controller on the motherboard. Despite already disabling this, I have tried this with both Fedora and Ubuntu without any success. I need to know what I can do about this; has anyone ran into something similar or heard about this issue before? I know these motherboards are relatively new...

  Read the article

• multiple streaming servers behind a Bastion Host

  - by Bond

  I am using open source streaming server Red5 on multiple servers. Which are running behind a bastion host. the world knows these sites as http://site1.mydomain.com http://site2.mydomain.com http://site3.mydomain.com http://site4.mydomain.com To reach the front end server is using Apache Reverse Proxy. I am also having video streaming on each of these websites using rtmp. To be able to reach the streaming server I embed a javascript in HTML pages as follows Code: <embed ..... var="rtmp://site1.my_domain.com" > the problem is the website are many site1.mydomain.com site2.mydomain.com site3.mydomain.com site4.mydomain.com each on a separate physical server. Each of these four have their own Red5 installations the front end to each of these four is a common Bastion Host. If I run rtmp on each of the subdomains at a different port how will I make sure a request such as rtmp://site1.mydomain.com rtmp://site2.mydomain.com goes to their respective servers. from the front end server. What do I need to handle in this case ? IPTABLES came to mind instantly but from the client browser on internet when some one requests rtmp://site1.mydomain.com how will I make sure this rtmp request is mapped to a port different than 1935 as there are three other streaming servers which are also to respond to their respective requests ?

  Read the article

• Sharing disk volumes across OpenVZ guests to reduce Package Management Overhead

  - by andyortlieb

  Is it feasible to create a single "master" OpenVZ guest who would only be used for package management, and use something like mount --bind on several other OpenVZ guests sort of trick them into using the environment installed by the master guest? The point of this would be so that users can maintain their own containers, and yet stay in sync with the master development environment, so they'll always have the latest & greatest requirements without worrying too much about system administration. If they need to install their own packages, could put them in /opt, or /usr/local (or set a path to their home directory)? To rephrase, I would like several (developer's, for example) OpenVZ guests whose /bin, /usr (and so on...) actually refer to the same disk location as that of a master OpenVZ guest who can be started up to install and update common packages for the environment to be shared by all of this group of OpenVZ guests. For what it's worth, we're running Debian 6. Edit: I have tried mounting (bind, and readonly) /bin, /lib, /sbin, /usr in this fashion and it refuses to start the containers stating that files are already mounted or otherwise in use: Starting container ... vzquota : (error) Quota on syscall for id 1102: Device or resource busy vzquota : (error) Possible reasons: vzquota : (error) - Container's root is already mounted vzquota : (error) - there are opened files inside Container's private area vzquota : (error) - your current working directory is inside Container's vzquota : (error) private area vzquota : (error) Currently used file(s): /var/lib/vz/private/1102/sbin /var/lib/vz/private/1102/usr /var/lib/vz/private/1102/lib /var/lib/vz/private/1102/bin vzquota on failed [3] If I unmount these four volumes, and start the guest, and then mount them after the guest has started, the guest never sees them mounted.

  Read the article

• Is it possible to detect nearby Wi-Fi enabled devices, not necessarily on the same network? [closed]

  - by Sky

  first question on StackExchange ever. I hope I got the right board. I'm trying to create a device (either from a standard AP or some other unconventional means) that will be able to detect nearby Wi-Fi enabled devices. For example, if a cellular phone (iPhone for instance) would be carried into the secured area, its MAC address will be logged. A cellular phone is a good example because it's the most common threat that should be detected. Some important points: The detection can be either active or passive, doesn't matter. The detected device might be connected to a different network, or might not be connected to anything at all. I assume most cellular phones are actively probing when not connected, but I'm not sure. It is important to not only identify the breach, but also to identify the device (MAC address). Conventional hardware is only optional. Distance of detection is at least 6 meters (20 feet). Handling one device at a time is good. Speed of detection is important, under 5 seconds is ideal. So my question is, is this even possible? If so, what can I use in order to make this a reality? Thank you for reading!

  Read the article

• needing storage integrity (write/read) test - for BASH

  - by Mr. Bash

  In need of shell scripts / bash commands to verify data integrity of local harddrives, usb-drives, etc, ... Like the famous www.heise.de/download/h2testw; or something that is at least common within repositories. (h2testw writes a specific datastring over and over onto the medium, then reads it again to verify if it was written correctly and displays write/read time/speed.) please no dd if=/dev/random of=/dev/sdx bs=1k && dd if=/dev/sdx of=/dev/null bs=1k since it won't verify if everything was written correctly. It is only a test if read/write is successful to the device. So far, I'm not too happy with badblocks -w -v /dev/sdx1 either, since it seems rather slow and I don't know what it exactly writes, and if it considers wear-leveling on flash media. There is also a program named F3 http://oss.digirati.com.br/f3/ that needs to be compiled. Designed after h2testw, the concept sounds interesting, i'd just rather have it as a ready to go bash script.

  Read the article

• Apache, suexec, PHP, suPHP

  - by Chris_K

  While I'm quite comfortable as a Linux user, my Linux Admin-fu is a bit weak. Thus, I'm here looking for guidance with a CentOS server I'm about to build. I need to setup an Apache2 web server for a few of our clients. I want each client's web content to be under their home directory (USERDIR in apache.conf, right?) for the static HTML sites. I want Apache to run as the client (suexec?). Some of their stuff will be PHP apps and I'm under the impression I'll want to look at suphp as well then. So basically I want to look like a small version of a shared web hosting company. Considering how common those are I thought I'd easily find a nice current How-To guide on setting this all up but so far I've had very little luck. I suspect my search words are off. So the questions (feel free to answer any or all): Anyone have some solid links to current/modern guides that would help me set this all up? No, the apache documentation site is not a guide ;-) Since I have a mix of static sites and PHP apps do I want/need both suexec and suphp installed? If so, does that introduce any challenges I should be aware of? Should I be looking at other options instead of suexec and suphp? I plan to give the end users SSH, SFTP or SCP access to their stuff (if that affects anything). Thanks in advance for your help.

  Read the article

• Is "DSLAM congestion" a legitimate reason for slow DSL?

  - by Jay Bazuzi

  My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

  Read the article

• duplicity fail: not promping for password: "Running 'sftp user@host' failed"

  - by Thr4wn

  I have two linode VPS accounts and I want to back up one onto the other (the reasons are mainly for fun and to practice server administration.) the short version Duplicity isn't even asking for my password, but immediately says "invalid SSH password" (but I can ssh into the other server). why? the long version When I run duplicity /home/me scp://[email protected]//root/backup I get Invalid SSH password Running 'sftp [email protected]' failed (attempt #1) Invalid SSH password Running 'sftp [email protected]' failed (attempt #2) Invalid SSH password Running 'sftp [email protected]' failed (attempt #3) And it says Invalid SSH password immediately with no opportunity for me to actually type the password. When I type duplicity full -v9 --num-retries 4 /home/me scp://[email protected]//root/backup I get Main action: full Running 'sftp [email protected]' (attempt #1) State = sftp, Before = 'Connecting to 97.107.129.67... [email protected]'s' State = sftp, Before = '' Invalid SSH password Running 'sftp [email protected]' failed (attempt #1) I can ssh into [email protected] fine, and in fact have the ip in known_hosts before I tried any of this. serer 1 (from which I'm running the duplicity command) is Linode's default Ubuntu 8 setup with only a handful of programs installed via apt-get. server 2 (represented by x.x.x.x) is literally only Linode's default Ubuntu 8 setup I previously tried using SystemImager -- would that have changed settings in a destructive way? (I have removed and rebooted since then) Isn't Duplicity supposed to prompt for password? Am I using it wrong? are there common mistakes/dependencies I need to know about? Is there any way that x.x.x.x could be setup that could make this not work (I used Linode's default Ubuntu 8 setup and barely )?

  Read the article

• PHP - Centos OpenSSL error

  - by mabbs

  i'm currently having a problem with OpenSSL on my Centos 6.5 Server. it ran perfectly fine until sunday. and i checked the error_log and i saw this error in the log PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/openssl.so' - /usr/lib64/php/modules/openssl.so: cannot open shared object file: No such file or directory in Unknown on line 0 i tried phpinfo(); and i found that openssl is enabled i tried php -m it returned [PHP Modules] bz2 calendar Core ctype curl date dom ereg exif fileinfo filter ftp gd gettext gmp hash iconv interbase json libxml mbstring mcrypt memcache mysql mysqli openssl pcntl pcre PDO PDO_Firebird pdo_mysql pdo_sqlite Phar pspell readline Reflection session shmop SimpleXML snmp sockets SPL sqlite3 standard tokenizer wddx xml xmlreader xmlrpc xmlwriter xsl zip zlib UPDATE this is what i got from rpm -qa | grep php just like what Mike Suggested php-php-gettext-1.0.11-3.el6.noarch php-mcrypt-5.3.3-3.el6.x86_64 php-interbase-5.3.3-3.el6.x86_64 php-pdo-5.3.3-27.el6_5.1.x86_64 php-5.3.3-27.el6_5.1.x86_64 php-mysql-5.3.3-27.el6_5.1.x86_64 php-snmp-5.3.3-27.el6_5.1.x86_64 php-gd-5.3.3-27.el6_5.1.x86_64 php-xml-5.3.3-27.el6_5.1.x86_64 php-pear-1.9.4-4.el6.noarch php-pecl-memcache-3.0.5-4.el6.x86_64 phpMyAdmin-3.5.8.2-1.el6.noarch php-common-5.3.3-27.el6_5.1.x86_64 php-cli-5.3.3-27.el6_5.1.x86_64 php-devel-5.3.3-27.el6_5.1.x86_64 php-mbstring-5.3.3-27.el6_5.1.x86_64 php-xmlrpc-5.3.3-27.el6_5.1.x86_64 php-pspell-5.3.3-27.el6_5.1.x86_64

  Read the article

• How small (spec wise) can a virtual machine be and still boot up and run some sort of OS?

  - by IllvilJa

  One of the advantages with virtual machines is that you can be very flexible with their sizes. If the host system permits it, you can have a very large virtual machine with a lot of virtual RAM and disk. Also, you can decide to go the other way around, to give the virtual machine a very modest amount of RAM and disk and then choose and configure the OS appropriately. The question is, how small virtual machines have people managed to setup (and get to both boot up and to run)? Virtual machines doing something usuful is preferable, even if I know "useful" in this context is awfully subjective, but laboratory-cases with a configuration stripped beyond common sense could be intresting as well, just to see what people manage to boot and run. Quite open ended question and quite academic, but think of it: an extremely small VM (which still does something useful) takes very little memory and disk and can be quite quickly saved to and restored from disk. If it's also gentle on CPU resources, one might consider having a huge number of such VMs up and running on a host. (Imagine a VM running just an old Commodore 64 or Commodore Amiga in it. Ok, way wrong CPU architecture for modern Virtualization software running on a x86-based PC but still an interesting thought. You could have quite a few such small VMs running on a modern PC.)

  Read the article

• Adding 2008 Server to 2008 Domain

  - by Phillip

  Hello, I'm trying to create a lab for testing before I deploy solutions, I'm no experienced IT Administrator, and therefore I come here for help. I'm running 2 Virtual Servers on the same machine on a local connection between those two. They'are able to ping each other. Their names is TSDATA1 and TSDATA2 where TSDATA1 is the Domain Controller. I am able to ping between those two, on both "ping TSDATA1" and "ping 10.0.0.1" which is the IP address of TSDATA1. The IP address of TSDATA2 is 10.0.0.2. I'm trying to join the domain with TSDATA2 both I'm getting this error when trying: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt. The following error occurred when DNS was queried for the service location (SRV) resource record used to locate an Active Directory Domain Controller for domain tsdata.local: The error was: "DNS name does not exist." (error code 0x0000232B RCODE_NAME_ERROR) The query was for the SRV record for _ldap._tcp.dc._msdcs.tsdata.local Common causes of this error include the following: The DNS SRV records required to locate a AD DC for the domain are not registered in DNS. These records are registered with a DNS server automatically when a AD DC is added to a domain. They are updated by the AD DC at set intervals. This computer is configured to use DNS servers with the following IP addresses: 10.0.0.1 One or more of the following zones do not include delegation to its child zone: tsdata.local local . (the root zone) For information about correcting this problem, click Help. I've figured out it has something to do with DNS lookup, but I have no clue what to do. Can anyone help?

  Read the article

• Joining an Ubuntu 14.04 machine to active directory with realm and sssd

  - by tubaguy50035

  I've tried following this guide to set up realmd and sssd with active directory: http://funwithlinux.net/2014/04/join-ubuntu-14-04-to-active-directory-domain-using-realmd/ When I run the command realm –verbose join domain.company.com –user-principal=c-u14-dev1/[email protected] –unattended everything seems to connect. My sssd.conf looks like the following: [nss] filter_groups = root filter_users = root reconnection_retries = 3 [pam] reconnection_retries = 3 [sssd] domains = DOMAIN.COMPANY.COM config_file_version = 2 services = nss, pam [domain/DOMAIN.COMPANY.COM] ad_domain = DOMAIN.COMPANY.COM krb5_realm = DOMAIN.COMPANY.COM realmd_tags = manages-system joined-with-adcli cache_credentials = True id_provider = ad krb5_store_password_if_offline = True default_shell = /bin/bash ldap_id_mapping = True use_fully_qualified_names = True fallback_homedir = /home/%d/%u access_provider = ad My /etc/pam.d/common-auth looks like this: auth [success=3 default=ignore] pam_krb5.so minimum_uid=1000 auth [success=2 default=ignore] pam_unix.so nullok_secure try_first_pass auth [success=1 default=ignore] pam_sss.so use_first_pass # here's the fallback if no module succeeds auth requisite pam_deny.so # prime the stack with a positive return value if there isn't one already; # this avoids us returning an error just because nothing sets a success code # since the modules above will each just jump around auth required pam_permit.so # and here are more per-package modules (the "Additional" block) auth optional pam_cap.so However, when I try to SSH into the machine with my active directory user, I see the following in auth.log: Aug 21 10:35:59 c-u14-dev1 sshd[11285]: Invalid user nwalke from myip Aug 21 10:35:59 c-u14-dev1 sshd[11285]: input_userauth_request: invalid user nwalke [preauth] Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_krb5(sshd:auth): authentication failure; logname=nwalke uid=0 euid=0 tty=ssh ruser= rhost=myiphostname Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_unix(sshd:auth): check pass; user unknown Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=myiphostname Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_sss(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=myiphostname user=nwalke Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_sss(sshd:auth): received for user nwalke: 10 (User not known to the underlying authentication module) Aug 21 10:36:12 c-u14-dev1 sshd[11285]: Failed password for invalid user nwalke from myip port 34455 ssh2 What do I need to do to allow active directory users the ability to log in?

  Read the article

• ssh key questions

  - by Tim

  I have some questions regarding generating keys for ssh access: (1) Supposed there are two computers running ssh server service and I have generated a pair of key files on computer A and copy the public file to computer B. Is it true that this is only a one-way key: We only gave computer A permission to access computer B, not gave computer B permission to access computer A? If I now want to ssh from computer B to computer A, must I generat another pair of key files on computer B and copy the public file to computer A? (2) If I would like to connect a single local computer to several remote servers, is it to generate a common pair of key files only once on the local and copy the same public file to the remote servers, or to generate different pair of key files on the local for different remote servers? (3) If I would like to connect several local computers to a single remote server, when copying the public files from different local computers to the remote server, is it to combine them together into a single authorized_keys file or store them in different authorized_keys files? (4) If there are several servers shared the same file system by, for example, NFS, how to generate keys and arrange the key files for accessing from one server to the other? Also how to still generate keys and arrange the key files for a local computer to access anyone of the servers? All the machines above are Linux.Please provide examples and commands in your reply so that I can better understand how to solve the problems. Thanks and regards!

  Read the article

• Working with barcode fonts in Word

  - by Bob Rivers

  I need to create labels in Microsoft Word 2010 with numbers encoded as barcodes. The barcode's format (ean, code39, upc, etc) does not matter. I have downloaded a barcode conversion font that I found at this site. When I type the number that I want and then I format it with my new font, it produces a barcode. I then print it on an OKI laser printer (1200 dpi). The result seems to be fine, at least for common people. But, when I try to scan it, nothing happens. I tried both with a barcode scanner and a data collector, but neither of them read the barcode. My barcode scanner is working fine, because I can read commercial barcodes printed on products. Does anybody have any advice? How do I do this kind of stuff? I want to do it using Word because I will generate labels using Mail Merge. Therefore using external programs aren't option for me.

  Read the article

• emacs, writing custom commands which use term-mode

  - by valya

  Hello, I'm using Emacs and M-x term for a terminal. Since my typical workflow looks like this: edit some code C-x C-o to the terminal buffer (or C-x b term[Enter] or something) press Up key to use the last command press Enter to run it C-x C-o to go back I want to bind all of these (except the first step... maybe) to one command, I believe Emacs is awesome enough to do that :-) So, a command must: go to the buffer with terminal (maybe it shouldn't change any windows at all, maybe it should split the window vertially (if it weren't split already) and use the right sid) run a last command what've been run there go back to the last buffer/part of the screen Thank you! I'm not really used to the Emacs scripting system, and I hope someone will help me and someone else will be able to use the answer to improve his workflow, since I believe this is a pretty common one Examples of commands: python manage.py test python manage.py test stats python solve.py # for project-euler puzzles :-) the first and the second runs over a ssh (in a terminal) sometimes (I like developing with vagrant) I understand that it's easy to bind the first and the third ones, but the second changes too often - I'd just like to "run last command"

  Read the article

• Cisco VPN endpoints disconnecting from a VLAN

  - by dunxd

  I have a number of Cisco ASA 5505 and PIX 506e around the world acting as VPN endpoints. They connect to a Cisco VPN Concentrator 3000 at HQ. I am using EZVPN to set up the VPN (i.e. most of the config is central on the VPN Concentrator) The majority of endpoints work absolutely fine. However, there are three that do not. 2 ASAs and 1 PIX get disconnected from one of the VLANs on our network. This is the VLAN that my monitoring server runs on - so those endpoints look as if they have gone down. However, I can still ping the endpoints from our user VLAN. If I then SSH onto the endpoint, and do a ping to my monitoring server, the connection comes back. Then after about 10 minutes it stops working again. I've looked at the configuration of my endpoints, and I can't see any significant differences. One common feature is that the affected endpoints are connecting to the internet via retail quality routers. However, I don't see how this could affect traffic within a VPN tunnel. Any ideas or suggestions? I've also got a thread on Cisco's forums at https://supportforums.cisco.com/thread/344638. One other person has reported the same problem.

  Read the article

• VMware vSphere 4.1 and BackupExec 2010

  - by Josh

  I'm sure a common problem with most shops is backups, their size, and the window in which you have to back up the data. What we are working with: VMware vSphere 4.1 Cluster PS4000XV Equallogic Storage Array (1.6TB Volume dedicated for Backup to Disk) Physical Backup Server with a single LTO4 drive. BackupExec 2010 R3 with the following agents, Exchange, SQL, Active Directory, VMware. Dual Gigabit MPIO Connections between all devices (Storage Array, Backup Server, VM Hosts) What we would like to accomplish: I would like to implement an efficient Backup to Disk to Tape solution where all of our VMs are backed up to the Storage Array first, and then once completely backed up to the array are replicated to tape. In the event we needed to recover, we would be able to do so directly from tape. Where we are at currently. Of the several ways I have setup the jobs in Backup Exec 2010 R3 the backup jobs all queue up at the same time, as soon as a job is finished backing up to disk it then starts that same job to tape, but pulling from the original source instead of the designated B2D location. I understand that I could create a job that backs up the "Backup to Disk" folder to tape, but in the event of restoration, I would first need to stage the data in the B2D folder before I could restore the VM. I would really like to hear from individuals in similar situations. Any and all comments and critiques are appreciated.

  Read the article

• What are some alternatives to word processing with Markdown?

  - by Hassan

  I've used MS Word-style editors for a long time, but I never got used to how unintuitive and cumbersome they are. I'm not talking specifically about MS Word, but also other editors that seem to mimic Word, like OpenOffice, NeoOffice, etc. I've found myself preferring to write in Markdown (much like on this site). I've found a few good Markdown editors, and I like using them a lot more than using Word-style editors. Here is what they generally look like: As you can see, it works much differently than a Word-style editor. This is a generally cleaner way of writing, since formatting is done right in the text, and is extremely simple to use (no highlighting some text, then clicking a button in some menu you have to find). Although editing text this way is great, I've realized that the syntax can only be used for very specific needs (bullets, numbered lists, headings and sub-headings, bold, italic, and some other common ones). However, many features are missing. Here are some features that would be nice in a word processor: Tables. Indenting paragraphs. Good image support (you can link to images, but not add them, since Markdown is just text). More simple to use than Word and its cronies. Cross-platform. Some of these can be fixed with in-line HTML, but nobody wants to do that. It seems Markdown was designed for editing text on the internet. Is there a similar setup that works better for desktop word processors?

  Read the article

• What is the collaborative screen shot/diagramming application recently featured on Hacker News and p

  - by wonsungi

  A few days ago, I saw this video for a screen capture application. I'm pretty sure I followed a link from Hacker News, possibly to a Life Hacker article. The video was very short, but demonstrated how the application could be used: The application was basically a movable/resize-able view port with a button. When the button is pressed, the contents of the view port are saved to an image (basically a screen capture.) The interesting thing is what you could do after that point. One of the specific examples from the video browsed to Google maps street view, grabbed a photo of an intersection, then scribbled notes about where to meet and where the restaurant was in colored "marker." Another example shown was grabbing a house layout from from CAD tool, then scribbling notes on it. The last part of the video showed several possible uses being scrolled through the application's view port. Now, it seemed it was very easy to share these images with other people because there was some type of integration, either with their own site and/or common social websites/chat services. The application was shown running on both Windows and Mac. edit: I think there was an iPhone app, as well. Anyone know what this application is? I tried searching Google, Hacker News, and Life Hacker already. It is not Jing.

  Read the article

< Previous Page | 260 261 262 263 264 265 266 267 268 269 270 271  | Next Page >