Search Results

Search found 8577 results on 344 pages for 'latest'.

Page 265/344 | < Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >

• Win/Bios showing wrong RAM in Gateway Netbook?

  - by Ael

  I've seen similar problems, but this seems slightly unique, maybe... I have a Gateway LT21 netbook, Win7. I've upgraded RAM from 1gb to 2gb. It didn't work. So I updated to the latest Bios 1.25, then it worked. 2gb was recognized in the Bios and in Windows. Every was fine. Now today it seemed slow and, to my surprise, both the Bios and Win show only 1gb. :/ I've run memory diagnostic, no error. I entered bios and hit Exit and Save. Still 1gb. I took out the ram, put it back. Still 1gb. :/ CPU-Z shows 2048mb/2gb of RAM. Further testing: if i put in the old 1gb ram, turn on, then put in the new 2gb ram again, the Bios and Win show 2gb of ram. BUT, once restarted at all (even from Bios) it seems to go back to showing incorrect 1gb ram again. :// (There are very few options in the bios, none appear memory-related.) Any ideas?

  Read the article

• Crond offset five minute schedule

  - by sam

  Is it possible to offset a cron script set to run every 5 minutes? I have two scripts, script 1 collects some data from one database and inserts it into another, script 2 pulls out this data and a lot of other data and creates some pretty reports from it. Both scripts need to run every 5 minutes. I want to offset script 2 by one minute so that it can create a report from the new data. E.G. I want script one to run at :00, :05, :10, :15 [...] and script two to run at :01, :06, :11, :16 [...] every hour. The scripts are not dependent on each other, and script 2 must run regardless of whether script one was successful or not. But it would be useful if the reports could have hte latest data. Is this possible with cron? Post; I have thought about using both commands in a shell script so they run immediately after each other but this wouldn't work, sometimes script 1 can get hung up on waiting for external APIs etc. so might take up to 15 mins to run, but script 2 must run every 5 minutes so doing it this way would stop/delay the execution of script 2. If I could set this in Cron it would mean script 2 would run regardless of what script 1 was doing

  Read the article

• Random server lag, no CPU/mem/pagefile usage

  - by Kev

  We have a fairly new server running Windows 2003 SP2, and the past few days we've noticed random slowdowns. When I'm logged into the server over remote desktop while this is happening, or if I'm physically sitting at the server logged in, suddenly everything becomes extremely laggy. Any UI element I try to interact with takes upwards of ten seconds to react, and then responds very slowly. Then a minute later everything is quite snappy again. During this, I have Task Manager minimized to the tray, and there's no CPU usage. I open it up right after this happens, and there's very little CPU usage on the graph, and no memory or pagefile usage above normal. (Normal being 1.5 GB free in the case of memory.) This is what I see logged into the server, and then users start calling saying things are slow, timing out, and failing--anything to do with our server. No events in the Event Viewer around the times this happens. The context I'm working in (last thing I clicked, etc.) seems different every time--different programs active, different combinations of programs open. Never anything particularly stressful (like adding an event entry to a Cobian Backup configuration, or editing text in TextPad, which has been exceptionally stable in my extensive usage of it.) I would've thought it was just the server, but a family member's home PC (entirely separate) running WinXPSP3 had the same thing happen to it last night a few times. Is this some new behaviour introduced by the latest Windows Updates? Either way, where do I even start to look when nothing seems to be chewing up resources?

  Read the article

• Why can't I get out of display mirror mode?

  - by Roy Smith

  I've been running Ubuntu (10.04.1 LTS, 64-bit) for a while and just replaced my hardware with a faster machine with an ATI Radeon HD 5700 video card. I've got twin 1920 x 1080 displays. I downloaded the latest driver (ati-driver-installer-10-9-x86.x86_64.run) from the ATI web site and installed that. I've gone through a few rounds of playing with /etc/X11/xorg.conf, and can't get things right. At the moment, it's in display mirroring mode, and I can't figure out how to get it out of mirror mode. If I run Monitor Preferences, there's a "Same image in all monitors" checkbox. If I uncheck that, the little preview window switches to show two monitors. When I click Apply, it asks me to log out and log back in again. When I do that, I'm right back to mirrored mode. What's really weird is that I'm currently running a copy of xorg.conf from a coworker's machine. He's got identical hardware, and his display works fine. So, I'm inclined to think there's something else going on other than the conf file. Any ideas what might be wrong?

  Read the article

• Linux: Can't overwrite files on samba store

  - by jonescb

  I'm using CentOS 5.5 with smbclient 3.0.33-3.28-el5 (latest version in repo), and I can't overwrite files in my Samba store. I am not the admin for the Samba server, so there isn't anything I can do server side. But I do have write permission to the server. I know the server runs Windows XP or Server 2003; I don't know. I can delete the file, and then copy the new version over, but I can't overwrite it. Using the cp command I'll get this error: [jonescb@localhost ~]$ cp foo.txt /mnt/si_storage/foo.txt cp: cannot create regular file `/mnt/si_storage/foo.txt': No such file or directory` And if I edit a file on the server using vim, I can save it once, but if I save it again I get this: "/mnt/si_storage/foo.txt" E212: Can't open file for writing This is my /etc/fstab entry for the samba server: //192.168.1.2/SI_STORAGE /mnt/si_storage cifs username=myuser,password=mypass 0 0 Edit: I can overwrite files just fine on my XP machine. The CentOS box is the only one having problems.

  Read the article

• iTunes Home Sharing only works one way between 2 Windows XP PC's on the same LAN

  - by scunliffe

  Both PC's have the latest iTunes installed. PC (A) can "see" that there is a shared library "B library" but attempts to connect to it return this error message: The shared library "{Username}'s Library" is not responding (-3259) Check that any firewall software running on either the shared computer or this computer has been set to allow communication on port 3689. however the reverse works fine. e.g. PC (B) can "see" shared library "A library" and can access all content. Notes: Both PC's have Home Sharing enabled (turned off/on several times to verify). Both PC's have Windows Firewall turned on, but in the exceptions tab, iTunes is allowed, and Port 3689 is also added as a firewall exception (just in case) Both iTunes accounts have been "authorized" on both PC's Both PC's connect via LAN via D-Link DIR-615 router. In the advanced application rules, iTunes has also been added to allow traffic on port 3689 un-hindered. Is there any other magical setting/configuration option that I should be aware of and set in order to get this to work? I could care less about sharing apps etc. I just want the music sharing to work. Update: Solved! It turns out on PC (B) there were multiple accounts set up. 1 of the accounts had the checkbox checked under the Windows firewall "On" option which states "No exceptions" thus even though it was added to the exception list on the main user account, this other account was blocking access.

  Read the article

• Is there any way to tweak / rotate mouse orientation? Any applications? Registry edits?

  - by calbar

  I've got a very frustrating issue with my new Logitech Marathon Mouse M705. It is absolutely perfect for what I need, with the exception that it tracks on an angle for some reason. What I mean is when you slide the cursor to the left, it trends upward - when you slide to the right, it trends down. Moving the cursor along a flat horizontal line is no longer a natural motion - you need to fight what I suspect is a mechanical error of some kind. Unfortunately, I've already exchanged this mouse once and tested both on different Windows 7 and Mac OS X machines - the problem continues to occur. Is there a software solution for me? I'm incredibly surprised there is no simple way to adjust the orientation... how can every mouse manufacturer possibly adjust their hardware to track to everyone's tastes? What about those who need to flip orientation a full 90 or 180 degrees? I only need to adjust mine a few degrees, but I'm sure that need has arisen as well. Anyway, I'm running the latest SetPoint drivers (6.00) on Windows 7 and there are no orientation options available. I've checked out uberOptions and the M705 isn't supported yet (with the last version update over 6 months ago). MAF Mouse instructions are a very strange series of mouse clicks to activate. This app also seems a little overkill and costs $$ (which I'm willing to pay as a last resort). Is there no universal registry value for mouse orientation? How about for SetPoint drivers specifically? I've done a simple search in regedit without any luck. An XML file somewhere? Anything?

  Read the article

• Mac dev folder missing, SSH not working

  - by SamGoody

  A few days ago, SSH stopped working. When I try logging in a get the following message: PTY allocation request failed on channel 0 stdin: is not a tty fatal: unrecognized command '' Connection to 74.52.61.194 closed. Web searches have shown me that there might be something wrong with /dev/std. But my computer lacks a /dev/ drive. There is an Alias to /dev/ [hidden, but I've revealed hidden files to do this search], but when I try to open it I am told that it cannot find the folder it is aliasing. Now, many a web search tells me that without a dev folder, the computer doesn't work, but it does seem to work, except the SSH. Also, are there any tools that can save my SSH preferences so that I don't have to, each time, type out the username@adrees, password, path all of which are long and complex? Not looking for a Filezilla type client, there are many of those. Looking for a command line like putty, that lets me use bash on the remote client. Am on Macbook Pro, latest version of Tiger.

  Read the article

• aufs user permissions

  - by user56395

  Anyone know why this doesn't work? Is this user error, AUFS feature or bug maybe: rac@tecraS1:~/tmp$ mkdir orig tmp au rac@tecraS1:~/tmp$ sudo mount -t tmpfs none tmp rac@tecraS1:~/tmp$ sudo chown -R rac tmp rac@tecraS1:~/tmp$ echo hello > orig/hello rac@tecraS1:~/tmp$ sudo mount -t aufs -o br=tmp:orig none au rac@tecraS1:~/tmp$ ls -al au total 8 drwxrwxrwt 4 rac root 100 2011-01-06 13:53 . drwxr-xr-x 5 rac rac 4096 2011-01-06 13:52 .. -rw-r--r-- 1 rac rac 6 2011-01-06 13:53 hello rac@tecraS1:~/tmp$ rm au/hello rm: cannot remove `au/hello': Operation not permitted rac@tecraS1:~/tmp$ Seems the aufs files were created as root and user has no access to them: rac@tecraS1:~/tmp$ sudo rm au/hello rac@tecraS1:~/tmp$ ls -al tmp total 4 drwxrwxrwt 4 rac root 120 2011-01-06 13:53 . drwxr-xr-x 5 rac rac 4096 2011-01-06 13:52 .. -r--r--r-- 2 root root 0 2011-01-06 13:53 .wh.hello -r--r--r-- 2 root root 0 2011-01-06 13:53 .wh..wh.aufs drwx------ 2 root root 40 2011-01-06 13:53 .wh..wh.orph drwx------ 2 root root 40 2011-01-06 13:53 .wh..wh.plnk rac@tecraS1:~/tmp$ OS is the latest Lucid with 2.6.35-23 stock kernel. No idea about aufs version. Using sudo chown -R rac tmp/.wh* fixes the problem. Thanks for looking.

  Read the article

• How to verify system using right GPU, after system reset [duplicate]

  - by Antoros

  This question already has an answer here: Is my mobile AMD card being used? 2 answers OS: Windows 8 CPU: Intel® Core™ i7 Processor 3635QM GPU 1 : Intel HD Graphics 4000 GPU 2 : AMD Radeon™ HD 8870M other info: System Spects Problem: im unsure that CCC is using AMD card instead of Intel's, i have encountered several issues since updating to 8.1 and i don't know what to do What happened: Installed 8.1 patch first day After 1 minute of use, BBSOD, windows never loaded again System restore wouldnt recognize 8.0 restore points i did a system reset to windows 8 since the laptop was only 3 weeks old System Broke, it did restore to factory BUT kept the registry almost intact, i had to install almost everything again, since the factory drivers where working with the updated one's registry and several problems CCC Broke too <- What i've already done Installing new drivers on top of old ones didnt work, so i used AMD uninstaller first Uninstalled and Re-installed Intel's HD Graphics Driver Tried to install mobile center, but AMD told me that it wasnt compatible (even if thats the only driver that they provide via their page as seen Here) Tried to use Auto-Detect, couldnt install driver because card was disabled because it didnt have the drivers... (see what they did here?) Had to use a workaround with Samsung Update, the driver didnt appear as download so had to use search and downloaded the driver manually. Now the graphic card appears on device manager and catalyst but as 8800 series (not exact model), and cant check the card with neither dxdiag/GPU-z/HWMonitor when right-clicking on CCC only Intel card appears launching a game and using as "high performance" would speed it up a little but i cant be sure How to verify its working properly? HWMonitor wont show AMD card even when set to high performance Latest GPU-Z wont work because a problem with Intel's, and legacy ones wont either what can I do now? I don't even know if I fixed my problem or not, and i also want to to use Adobe Premier with it, and its locked (the option to run it with the amd card not intels) Edit: now it seems to work, but cant change the setting for adobe Premiere and other programs that i Need to

  Read the article

• tc u32 --- how to match L2 protocols in recent kernels?

  - by brownian

  I have a nice shaper, with hashed filtering, built at a linux bridge. In short, br0 connects external and internal physical interfaces, VLAN tagged packets are bridged "transparently" (I mean, no VLAN interfaces are there). Now, different kernels do it differently. I can be wrong with exact kernel verions ranges, please forgive me. Thanks. 2.6.26 So, in debian, 2.6.26 and up (up to 2.6.32, I believe) --- this works: tc filter add dev internal protocol 802.1q parent 1:0 prio 100 \ u32 ht 1:64 match ip dst 192.168.1.100 flowid 1:200 Here, "kernel" matches two bytes in "protocol" field with 0x8100, but counts the beginning of ip packet as a "zero position" (sorry for my English, if I'm a bit unclear). 2.6.32 Again, in debian (I've not built vanilla kernel), 2.6.32-5 --- this works: tc filter add dev internal protocol 802.1q parent 1:0 prio 100 \ u32 ht 1:64 match ip dst 192.168.1.100 at 20 flowid 1:200 Here, "kernel" matches the same for protocol, but counts offset from the beginning of this protocol's header --- I have to add 4 bytes to offset (20, not 16 for dst address). It's ok, seems more logical, as for me. 3.2.11, the latest stable now This works --- as if there is no 802.1q tag at all: tc filter add dev internal protocol ip parent 1:0 prio 100 \ u32 ht 1:64 match ip dst 192.168.1.100 flowid 1:200 The problem is that I couldn't find a way to match 802.1q tag so far. Matching 802.1q tag at past I could do this before as follows: tc filter add dev internal protocol 802.1q parent 1:0 prio 100 \ u32 match u16 0x0ed8 0x0fff at -4 flowid 1:300 Now I'm unable to match 802.1q tag with at 0, at -2, at -4, at -6 or like that. The main issue that I have zero hits count --- this filter is not being checked at all, "wrong protocol", in other words. Please, anyone, help me :-) Thanks!

  Read the article

• windows 7 monitor instantly resumes from power off

  - by user167328

  It seems that some service or program is preventing my monitor from going into power save mode but I cannot find a way to dig down the cause. Does anybody know a way to find out which event may be causing the problem? Background information: If I leave/lock my computer I want to immediately power off the monitor. Stupid windows has no program for this so I use a third party utility. I use Display.exe from Noel Danjou since 2005 and have had no problem with it on XP, my Notebook with w7 x64 pro and at the office with w7 x64 enterprise. With my new home pc with w7 x64 pro the monitor goes off but instantly comes back on after a second. So I tested using a power plan with the shortest timeout of 1 minute but with that the display never goes off at all. (Setting a power plan timeout is no useful option because then I cannot read a document or watch a movie without the monitor going off) I could try trial and error methods but this is cumbersome and not what I regard as a professional solution. So I would prefer a way to analyze the windows events to find out the reason for the display staying active. Add On: In the meantime I tried safe mode and also exited from all tray programs but the problem is still there. I also checked the BIOS for special power settings but still no solution (P.S. Mobo is H87-G41 PC Mate with latest BIOS rev.)

  Read the article

• Windows 7 Blank Screen on Boot / Login

  - by Greg

  I have a new system that's having a few problems... sometimes (seems to be when the PC is cold, i.e. has been switched off for a while, though that could be my imagination) I get a blank blue screen when I boot up. The system boots normally and auto-logs-in. The desktop loads and I'm even able to launch applications, but then everything disappears and the screen goes to the default windows desktop blue colour (not the desktop image, just a plain blue with no mouse cursor). At this point the machine completely locks up - I'm unable to even toggle Num Lock and have to hold in the power button for 5 seconds to kill it. Interestingly if I manage to launch some applications before it goes blank, they will usually crash... sometimes explorer.exe will crash too. When I reboot, the system is fine and stable. I've installed the latest graphics drivers and run memtest86+ for 6 passes (and counting) with no errors. The system specs are: CPU: Intel I7 2.66 @ 3.4GHz RAM: 6GB (3 * 2GB DDR3) HDD: 128GB Crucial M225 SSD Motherboard: Gigabyte EX58-UD3R Gfx: ATI Radeon Sapphire 5870 1GB Note: There are a few similar questions but I haven't found one that matches my symptoms

  Read the article

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• Why does my microwave kill the Wi-Fi?

  - by Ohlin

  Every time I start the microwave in the kitchen, our home Wi-Fi stops working and all devices lose connection with our router! The kitchen and the Wi-Fi router are in opposite ends of the apartment but devices are being used a little here and there. We've been annoyed by the instability of the Wi-Fi for some time and it wasn't until recently we realized it was correlated to microwave usage. After some testing with having the microwave on and off we could narrow down the problem to only occurring when the router is in b/g/n mode and uses a set channel. If I change to b/g mode or set channel to auto then there is no problem any more...but still! The router is a Zyxel P-661HNU ("802.11n Wireless ADSL2+ 4-port Security Gateway" with latest firmware) and the microwave is made by Neff with an effect of 1000W (if this information might be useful to anyone). There is an "internet connection" light on the router and it doesn't go out when the interruption occurs so I think this is only an internal Wi-Fi issue. Now to my questions: What parts of the Wi-Fi can possibly be affected by the microwave usage? Frequency? Disturbances in the electrical system? How can setting Auto on channels make a difference? I thought the different channels were just some kind of separation system within the same frequency spectrum? Could this be a sign that the microwave is malfunctioning and slowly roasting us all at home? Is there any need to be worried? Since we were able to find router settings that cooperate well with our microwave's demand for attention, this question is mainly out of curiosity. But as most people out there...I just can't help the fact that I need to know how it's possible :-)

  Read the article

• On clients use generic driver for printer shared by CUPS

  - by Daniel

  I know this worked really easy with a recent CUPS version some years ago. Unfortunately I fail to do the following with latest CUPS nowadays. How to share a printer without using printer specific drivers on the clients with CUPS? The printer is a Samsung ML-2010. The important fact is that it needs a quite specific library for printing called splix. That is installed on the server and prints well. What makes trouble is using that printer over the network. I found out how to use Avahi under Linux to make use of DNSSD to advertise and discover printers. But as far as I understand the new CUPS offers the internal driver interface on the network. This has 2 major issues: anybody can fiddle with the driver and I don't trust any uncommon printer library to be "network secure" anyone who wants to use my printer including guests needs to install the specific drivers first I remember the old days when I could enable "Share this printer" on the CUPS server and all clients would magically detect the printer and just send their job data to the server and have it do the driver stuff. After everything a read I guess this is related to the changes Apple introduced with CUPS including dropping of the integrated network discovery protocol. If it helps: Server: Ubuntu LTS 12.04 Server with CUPS 1.5.3 Client: Arch Linux with current CUPS 1.6.1 On another box with Ubuntu the printer was setup automatically at least but the mechanism used the Splix library for that.

  Read the article

• Computer crashes if left unattended AND running uTorrent, what could be?

  - by DiegoDD

  I have a weird problem in which, if I leave my computer unattended, AND I leave uTorrent open, downloading/seeding, the computer simply crashes after about 20 / 30 minutes (don't know exactly since if I leave it, and come back later, it has already restarted or has a BSOD.) If I leave the computer alone for undefined time WITHOUT uTorrent, nothing happens, and if I am constantly using the computer while using uTorrent, no problem either (I could be using it all day with uT open and it doesn't crash). So what could it be that the combination of those cases makes the computer crash? I have already checked the power management so the computer never enters stand by mode, sleep, hibernate, etc. (the only thing I do is turn off the display). A first guess is that maybe one of my external hard drives DO sleep or enters in a "low power" mode or something if I don't use the PC. but since uT is running MAYBE tries to use that drive, and makes it crash. Could that be possible? How to know for sure if the external drive does that, and to prevent it from doing so. Any more ideas of what may be causing that? Specs: Windows 7 Pro, 64-bit, 2 GB RAM. Latest version of uTorrent (although it has been happening for a while now). UPDATE: i just found out that uTorrent has Disk cache options ( preferences - advanced - disk cache ). I have no idea if that may be causing problems with my external drive, hence causing the crash.

  Read the article

• Getting Started in SuSE as an Ubuntu User

  - by Subhamoy Sengupta

  I am not a Linux newbie, but haven't touched SuSE in a very very long time (last time I tried it, it was SuSE 7!). Finally now I felt like giving it a try, and many things seem strange or unnecessarily complex. I have a series of questions. How do I ensure that my packages are uptodate? It sounds silly, but I tried the obvious methods already. I have disabled the default repositories that show up when you do zypper lr, and added Tumbleweed and packman repositories (Essentials, Multimedia, Extra). Then I did a sudo zypper ref --force and then sudo zypper dup, and it tells me many dependencies are not met. I have already added solder.allowVendorChange=true to /etc/zypp/zypp.conf, so it should not care which repository the latest versions are in, and just upgrade to it. Even when I chose to skip the packages with unmet dependencies, and seemed like quite a bit happened in the background, I opened Firefox afterwards and the version was 7! I am guessing things did not go as expected. But of course this is not a problem with SuSE, but I am not understanding the system right. How do I do it right? When I start typing arguments of a command, for example sudo zypper install, when I type sudo zypper ins and keep hitting TAB, nothing happens! It always worked in Ubuntu and I feel very uneasy with this. Is this how SuSE is supposed to be? When I try to install something, and I start writing its name, even though the package exists and I am sure of it, hitting TAB does not autocomplete it. This is also quite inconvenient. Why is it not happening? There are many things in SuSE that are really great, and I think I will stay with it and not go back to Ubuntu once I settle these very rudimentary issues. But right now they are giving me a lot of grief! Please help!

  Read the article

• Gigabyte H55N-USB3: No video on HDMI

  - by newt

  I built a new PC with a Gigabyte H55N-USB3 / Intel Core i5 650. With a monitor plugged in the DVI port, everything works fine. I installed Windows 7 32-bit and enabled remote desktop connection. After that, I unplugged the monitor, plugged it into network and installed everything else (drivers, programs, etc) via RDP. However, when I try to use the HDMI port on my TV nothing appears. Neither during the boot, neither after Windows starts. The TV says there's "no signal" (if I remove the cable the message changes to "check cable"). The cable is new, and it is working fine with my home theater on same TV (by the way, it is the cable which came bundled with the home theater). Video driver is the latest from Intel site. Anyway, this shouldn't be the problem since there is no image during the boot. Any ideas or tips would be welcome. I'm googling around but found nothing useful, yet.

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: How do I remove the option to eject SATA drives from the Windows 7 tray icon?

  Read the article

• Why does GIMP start up so slow on my machine?

  - by muntoo

  EDIT 2: One way would be to disable script-fu. Does anyone know how to disable it at startup? Is it possible? Would GIMP still work? What wouldn't work? Could I start it later, after loading? Is there any way to speed up GIMP's startup time on Windows Vista Home Premium 32-Bit 1.6 [Dual] Intel Processors? On XP [different computer], it loads in less than 3 seconds. On Vista, it takes 20 seconds: 2 Seconds (other - fonts, brushes, etc) 18 Seconds (extension-script-fu) It just freezes at extension-script-fu. Looking at Process Explorer, I see that it's not taking any CPU at all. EDIT 1: It does seem to be taking 50% of the CPU. It gets stuck for about 18 seconds, and then starts working again. Then, the actual GIMP program pops up [...finally]. I have the latest stable version running (I think). I tried it with XP SP2 Compatibiliy mode and/or Run As Administrator, but that didn't help.

  Read the article

• WAMP Installation - Multiple PHP Version Issues

  - by Pete171

  I have installed WAMP because I am attempting to modify an an application which uses Zend Optimizer (I cannot use Z.O. with PHP5.3+, which is why I decided to install WAMP). I downloaded the latest version - Wamp Server 2.1 - which comes bundled with PHP5.3.5. I then downloaded a PHP version that would be compatible with Z.O. - 5.2.9. - and a compatible Apache version, 2.0.63. My problem: PHP scripts run fine, but anything with MySQL does not work. Running the testmysql.php script returns the fatal error: Fatal error: Call to undefined function mysql_connect() in C:\wamp\www\testmysql.php on line 2". I have looked in the PHP INI files inside both PHP versions, and I'm fairly sure the relevant information is there. At least, there are parts inside that mention MySQL! Perhaps somebody could clarify exactly what information should be present? Also, when visiting a page that called phpinfo(), I noticed that the 'Loaded Configuration File' was pointing to C:\wamp\bin\php\php5.3.5\php.ini, even though I have enabled the older PHP version. I've stopped and started Apache, too, and that hasn't made a difference. Is anybody able to offer any assistance? Anything at all would be great; I'm not very good at messing around with Apache/

  Read the article

• Why won't Media Monkey add one particular folder of mp3's?

  - by ChrisF

  I'm using the latest and greatest version on Media Monkey (free version) and it won't find the mp3's in one particular folder in my music tree. It can see all the other files in the tree and the folder shows up when I click Add/Rescan files to the library... I have full control over the folder and all the files in the folder. The files play in Windows Media Player. The files play in Media Monkey if I right click and play from the context menu. All the tracks are at least 2 minutes long and over 5MB long and Media Monkey is set to ignore files shorter than 20KB and include all files regardless of length. There was an issue in that the that the genre of the tracks was set to "Classical" and the option that allows you to browse the classical music independently of the other music isn't enabled in the free version. It's a Gold version option only. I hadn't spotted that my other classical music was also missing from the library (I have rather a large library). Once I retagged the music with a different tag and tried to add the files again it reported that it added the tracks, but they still didn't show up in the library.

  Read the article

• Google Drive terminates without error on startup

  - by Iszi

  I've used Google Drive for awhile now, but it won't start up after installing on my latest system re-build. I'm still using the same OS, hardware, and basic software load (antivirus, firewall, etc.) that I have for years during which I had not previously had problems with Drive. OS: Windows 7 Ultimate x64 Google Drive Version: 1.12.5329.1887 Now, whenever I try to run Google Drive, it just spawns two instances of the executable which die shortly after. No error messages are posted to the desktop, and nothing indicating any problem is written to the Event Log. After some research, I've yet to find anyone having the same problem who's found an answer. I did find out how to run Google Drive in diagnostic mode, using the --vv parameter at the command line. After that, I opened up the sync log and got this: 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 OS: Windows/6.1.7601-SP1 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 Google Drive (build 1.12.5329.1887) 2013-10-31 17:11:24,039 DEBUG pid=3664 1892:MainThread logging:1608 DEBUGGING DUMP is ON. 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 ERROR, UNEXPECTED EXCEPTION 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 [Error 5] Access is denied Traceback (most recent call last): File "<string>", line 232, in Main File "<string>", line 118, in RegisterCustomFileTypes File "P:\p\agents\hpal4.eem\recipes\353983091\base\b\drb\googleclient\apps\webdrive_sync\windows\build\pyi.win32\main\outPYZ1.pyz/windows.registry", line 62, in GetValue WindowsError: [Error 5] Access is denied 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Crash reporting disabled. Ignoring report. 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Exiting with error code: 0 I'm running on an account with Administrator-level permissions, and have even tried using "Run As Administrator" on the EXE. I'm not sure why it's looking for a P:\ drive, as no such volume has ever been mounted on this system. What should I do to try to further troubleshoot, and resolve, this issue?

  Read the article

• WSUS performance for unneeded updates

  - by mhouston100

  We have a WSUS server serving around 300 PC's and a couple of dozen servers and a discussion came up at work as to what products to include. We have a single SQL 2005 instance on one of the servers and it has NEVER been updated. My first thought was to just tick the box for SQL 2005 and let WSUS do it's thing to upgrade to the latest service pack at least. One of the other guys here has the opinion that having updates that are relevant to only a small selection of hosts would effect the performance of WSUS as a whole, claiming that each update does a 'check' against all the hosts or something similar. My argument is that manually updating these servers is obviously not working as the admins are not paying attention to what is needed. So my question is: Do updates that only effect a sub-set of the hosts effect the overall performance of the WSUS server in relation to ALL the hosts? (disk space is not an issue at this point) Is there any performance justification for or against manually updating small amounts of products? Basically I'm needing a rebuttal against his argument and I'm unable to find any concrete documentation to prove him wrong.

  Read the article

< Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >