Search Results

Search found 6815 results on 273 pages for 'micro sd card'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 266/273 | < Previous Page | 262 263 264 265 266 267 268 269 270 271 272 273  | Next Page >

  • Bypass BIOS password set by faulty Toshiba firmware on Satellite A55 laptop?

    - by Brian
    How can the CMOS be cleared on the Toshiba Satellite A55-S1065? I have this 7 year old laptop that has been crippled by a glitch in its BIOS: 'A "Password =" prompt may be displayed when the computer is turned on, even though no power-on password has been set. If this happens, there is no password that will satisfy the password request. The computer will be unusable until this problem is resolved. [..] The occurrence of this problem on any particular computer is unpredictable -- it may never happen, but it could happen any time that the computer is turned on. [..] Toshiba will cover the cost of this repair under warranty until Dec 31, 2010.' -Toshiba As they stated, this machine is "unusable." The escape key does not bypass the prompt (nor does any other key), thus no operating system can be booted and no firmware updates can be installed. After doing some research, I found solutions that have been suggested for various Toshiba Satellite models afflicted by this glitch: "Make arrangements with a Toshiba Authorized Service Provider to have this problem resolved." -Toshiba (same link). Even prior to the expiration of Toshiba's support ("repair under warranty until Dec 31, 2010"), there have been reports that this solution is prohibitively expensive, labor charges accruing even when the laptop is still under warranty, and other reports that are generally discouraging: "They were unable to fix it and the guy who worked on it said he couldn’t find the jumpers on the motherboard to clear the BIOS. I paid $39 for my troubles and still have the password problem." - Steve. Since the costs of the repairs can now exceed the value of the hardware, it would seem this is a DIY solution, or a non-solution (i.e. the hardware is trash). Build a Toshiba parallel loopback by stripping and soldering the wires on a DB25 plug to connect connect these pins: 1-5-10, 2-11, 3-17, 4-12, 6-16, 7-13, 8-14, 9-15, 18-25. -CGSecurity. According to a list of supported models on pwcrack, this will likely not work for my Satellite A55-1065 (as well as many other models of similar age). -pwcrack Disconnect the laptop battery for an extended period of time. Doesn't work, laptop sat in a closet for several years without the battery connected and I forgot about the whole thing for awhile. The poor thing. Clear CMOS by setting the proper jumper setting or by removing the CMOS (RTC) battery, or by short circuiting a (hidden?) jumper that looks like a pair of solder marks -various sources for various Satellite models: Satellite A105: "you will see C88 clearly labeled right next the jack that the wireless card plugs into. There are two little solder squares (approx 1/16") at this location" -kerneltrap Satellite 1800: "Underneath the RAM there is black sticker, peel off the black sticker and you will reveal two little solder marks which are actually 'jumpers'. Very carefully hold a flat-head screwdriver touching both points and power on the unit briefly, effectively 'shorting' this circuit." -shadowfax2020 Satellite L300: "Short the B500 solder pads on the system board." -Lester Escobar Satellite A215: "Short the B500 solder pads on the system board." -fixya Clearing the CMOS could resolve the issue, but I cannot locate a jumper or a battery on this board. Nothing that looks remotely like a battery can be removed (everything is soldered). I have looked closely at the area around the memory and do not see any obvious solder pads that could be a secret jumper. Here are pictures (click for full resolution) : Where is the jumper (or solder pads) to short circuit and wipe the CMOS on this board? Possibly related questions: Remove Toshiba laptop BIOS password? Password Problem Toshiba Satellite..

    Read the article

  • Splitting a raidctl mirror safely

    - by milkfilk
    I have a Sun T5220 server with the onboard LSI card and two disks that were in a RAID 1 mirror. The data is not important right now but we had a failed disk and are trying to understand how to do this for real if we had to recover from a failure. The initial situation looked like this: # raidctl -l c1t0d0 Volume Size Stripe Status Cache RAID Sub Size Level Disk ---------------------------------------------------------------- c1t0d0 136.6G N/A DEGRADED OFF RAID1 0.1.0 136.6G GOOD N/A 136.6G FAILED Green light on the 0.0.0 disk. Find / lights up the 0.1.0 disk. So I know I have a bad drive and which one it is. Server still boots obviously. First, we tried putting a new disk in. This disk came from an unknown source. Format would not see it, cfgadm -al would not see it so raidctl -l would not see it. I figure it's bad. We tried another disk from another spare server: # raidctl -c c1t1d0 c1t0d0 (where t1 is my good disk - 0.1.0) Disk has occupied space. Also the different syntax options don't change anything: # raidctl -C "0.1.0 0.0.0" -r 1 1 Disk has occupied space. # raidctl -C "0.1.0 0.0.0" 1 Disk has occupied space. Ok. Maybe this is because the disk from the spare server had a RAID 1 on it already. Aha, I can see another volume in raidctl: # raidctl -l Controller: 1 Volume:c1t1d0 (this is my server's root mirror) Volume:c1t132d0 (this is the foreign root mirror) Disk: 0.0.0 Disk: 0.1.0 ... No problem. I don't care about the data, I'll just delete the foreign mirror. # raidctl -d c1t132d0 (warning about data deletion but it works) At this point, /usr/bin/ binaries freak out. By that I mean, ls -l /usr/bin/which shows 1.4k but cat /usr/bin/which gives me a newline. Great, I just blew away the binaries (ie: binaries in mem still work)? I bounce the box. It all comes back fine. WTF. Anyway, back to recreating my mirror. # raidctl -l Controller: 1 Volume:c1t1d0 (this is my server's root mirror) Disk: 0.0.0 Disk: 0.1.0 ... Man says that you can delete a mirror and it will split it. Ok, I'll delete the root mirror. # raidctl -d c1t0d0 Array in use. (this might not be the exact error) I googled this and found of course you can't do this (even with -f) while booted off the mirror. Ok. I boot cdrom -s and deleted the volume. Now I have one disk that has a type of "LSI-Logical-Volume" on c1t1d0 (where my data is) and a brand new "Hitachi 146GB" on c1t0d0 (what I'm trying to mirror to): (booted off the CD) # raidctl -c c1t1d0 c1t0d0 (man says it's source destination for mirroring) Illegal Array Layout. # raidctl -C "0.1.0 0.0.0" -r 1 1 (alt syntax per man) Illegal Array Layout. # raidctl -C "0.1.0 0.0.0" 1 (assumes raid1, no help) Illegal Array Layout. Same size disks, same manufacturer but I did delete the volume instead of throwing in a blank disk and waiting for it to resync. Maybe this was a critical error. I tried selecting the type in format for my good disk to be a plain 146gb disk but it resets the partition table which I'm pretty sure would wipe the data (bad if this was production). Am I boned? Anyone have experience with breaking and resyncing a mirror? There's nothing on Google about "Illegal Array Layout" so here's my contrib to the search gods.

    Read the article

  • Wireless AAA for a small, bandwidth-limited hotel.

    - by Anthony Hiscox
    We (the tech I work with and myself) live in a remote northern town where Internet access is somewhat of a luxury, and bandwidth is quite limited. Here, overage charges ranging from few hundreds, to few thousands of dollars a month, is not uncommon. I myself incur regular monthly charges just through my regular Internet usage at home (I am allowed 10G for $60CAD!) As part of my work, I have found myself involved with several hotels that are feeling this. I know that I can come up with something to solve this problem, but I am relatively new to system administration and I don't want my dreams to overcome reality. So, I pass these ideas on to you, those with much more experience than I, in hopes you will share some of your thoughts and concerns. This system must be cost effective, yes the charges are high here, but the trust in technology is the lowest I've ever seen. Must be capable of helping client reduce their usage (squid) Allow a limited (throughput and total usage) amount of free Internet, as this is often franchise policy. Allow a user to track their bandwidth usage Allow (optional) higher speed and/or usage for an additional charge. This fee can be obtained at the front desk on checkout and should not require the use of PayPal or Credit Card. Unfortunately some franchises have ridiculous policies that require the use of a third party remote service to authenticate guests to your network. This means WPA is out, and it also means that I do not auth before Internet usage, that will be their job. However, I do require the ABILITY to perform authentication for Internet access if a hotel does not have this policy. I will still have to track bandwidth (under a guest account by default) and provide the same limiting, however the guest often will require a complete 'unlimited' access, in terms of existence, not throughput. Provide firewalling capabilities for hotels that have nothing, Office, and Guest network segregation (some of these guys are running their office on the guest network, with no encryption, and a simple TOS to get on!) Prevent guests from connecting to other guests, however provide a means to allow this to happen. IE. Each guest connects to a page and allows the other guest, this writes a iptables rule (with python-netfilter) and allows two rooms to play a game, for instance. My thoughts on how to implement this. One decent box (we'll call it a router now) with a lot of ram, and 3 NIC's: Internet Office Guests (AP's + In Room Ethernet) Router Firewall Rules Guest can talk to router only, through which they are routed to where they need to go, including Internet services. Office can be used to bridge Office to Internet if an existing solution is not in place, otherwise, it simply works for a network accessible web (webmin+python-webmin?) interface. Router Software: OpenVZ provides virtualization for a few services I don't really trust. Squid, FreeRADIUS and Apache. The only service directly accessible to guests is Apache. Apache has mod_wsgi and django, because I can write quickly using django and my needs are low. It also potentially has the FreeRADIUS mod, but there seems to be some caveats with this. Firewall rules are handled on the router with iptables. Webmin (or a custom django app maybe) provides abstracted control over any features that the staff may need to access. Python, if you haven't guessed it's the language I feel most comfortable in, and I use it for almost everything. And finally, has this been done, is it a overly massive project not worth taking on for one guy, and/or is there some tools I'm missing that could be making my life easier? For the record, I am fairly good with Python, but not very familiar with many other languages (I can struggle through PHP, it's a cosmetic issue there). I am also an avid linux user, and comfortable with config files and command line. Thank you for your time, I look forward to reading your responses. Edit: My apologies if this is not a Q&A in the sense that some were expecting, I'm just looking for ideas and to make sure I'm not trying to do something that's been done. I'm looking at pfSense now as a possible start for what I need.

    Read the article

  • Cannot ping host stale ARP cache?

    - by gkchicago
    I am having a strange issue with a Debian (Lenny/Linux 2.6.26-2-amd64) that has been driving me nuts. On some machines within my network I can ping the host in question just fine, other times I have to manually hard-code the ARP ethernet address for the IP in order to establish connectivity. I've finally worked it down to somehow involving ARP. I just found how to fix it in a way that made it work but I'm looking for help explaining this issue and also I don't trust my fix to be permanent.. My thought process has been the following but I just can't make any sense out of it: Could it be the card? (Intel 82555 rev 4) Could it be because there are two network cards? (Default route is eth0) Could it be because of the network aliases? Lenny? AMD x86_64? Argh.. Thank you for any insight you might have // Ping doesn't go thru [gordon@ubuntu ~]$ ping 192.168.135.101 PING 192.168.135.101 (192.168.135.101) 56(84) bytes of data. --- 192.168.135.101 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3014ms // Here's the ARP Table, sometimes the .151 address is good, sometimes it // also matches the Gateways MAC like .101 is doing right here. [gordon@ubuntu ~]$ cat /proc/net/arp IP address HW type Flags HW address Mask Device 192.168.135.15 0x1 0x2 00:0B:DB:2B:24:89 * eth0 192.168.135.151 0x1 0x2 00:0B:6A:3A:30:A6 * eth0 192.168.135.1 0x1 0x2 00:1A:A2:2D:2A:04 * eth0 192.168.135.101 0x1 0x2 00:1A:A2:2D:2A:04 * eth0 // Drop the bad arp table listing and set it manually based on /sbin/ifconfig [gordon@ubuntu ~]$ sudo arp -d 192.168.135.101 [gordon@ubuntu ~]$ sudo arp -s 192.168.135.101 00:0B:6A:3A:30:A6 // Ping starts going thru..?!? [gordon@ubuntu ~]$ ping 192.168.135.101 PING 192.168.135.101 (192.168.135.101) 56(84) bytes of data. 64 bytes from 192.168.135.101: icmp_seq=1 ttl=64 time=15.8 ms 64 bytes from 192.168.135.101: icmp_seq=2 ttl=64 time=15.9 ms 64 bytes from 192.168.135.101: icmp_seq=3 ttl=64 time=16.0 ms 64 bytes from 192.168.135.101: icmp_seq=4 ttl=64 time=15.9 ms --- 192.168.135.101 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3012ms rtt min/avg/max/mdev = 15.836/15.943/16.064/0.121 ms The following is my network config on this. gordon@db01:~$ /sbin/ifconfig eth0 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.151 Bcast:192.168.135.255 Mask:255.255.255.0 inet6 addr: fe80::20b:6aff:fe3a:30a6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15476725 errors:0 dropped:0 overruns:0 frame:0 TX packets:10030036 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18565307359 (17.2 GiB) TX bytes:3412098075 (3.1 GiB) eth0:0 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.150 Bcast:192.168.135.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:1 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.101 Bcast:192.168.135.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth1 Link encap:Ethernet HWaddr 00:e0:81:2a:6e:d0 inet addr:10.10.62.1 Bcast:10.10.62.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:81ff:fe2a:6ed0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10233315 errors:0 dropped:0 overruns:0 frame:0 TX packets:19400286 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1112500658 (1.0 GiB) TX bytes:27952809020 (26.0 GiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:387 errors:0 dropped:0 overruns:0 frame:0 TX packets:387 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:41314 (40.3 KiB) TX bytes:41314 (40.3 KiB) gordon@db01:~$ sudo mii-tool -v eth0 eth0: negotiated 100baseTx-FD, link ok product info: Intel 82555 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD gordon@db01:~$ sudo route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface localnet * 255.255.255.0 U 0 0 0 eth0 10.10.62.0 * 255.255.255.0 U 0 0 0 eth1 default 192.168.135.1 0.0.0.0 UG 0 0 0 eth0

    Read the article

  • Python in command line runs the wrong version?

    - by Deflect
    I have several versions of Python installed on a Windows 7 computer. I want to run Python 2.7 by default, but for whatever reason, typing python in the command line runs Python version 2.4.5. I've tried adding C:\Python27 to my system path variable as per this question, and manually combed my path variable it to make sure Python 2.4.5 wasn't tossed in there by mistake, but that didn't fix the issue. I have to type in C:\Python27\python.exe every time I want to access the correct version of python I want. What other places can I check? How can I make the command line use the correct version of python? I also found this but it's not for windows. [EDIT] My path (separated by semicolons): C:\Program Files\Common Files\Microsoft Shared\Windows Live; C:\Program Files (x86)\Common Files\Microsoft Shared\Windows Live; C:\Windows\system32; C:\Windows; C:\Windows\System32\Wbem; C:\Windows\System32\WindowsPowerShell\v1.0\; C:\Program Files\Dell\DW WLAN Card\Driver; C:\Program Files (x86)\Common Files\Roxio Shared\DLLShared\; C:\Program Files (x86)\Windows Live\Shared; c:\Program Files (x86)\Microsoft SQL Server\100\Tools\Binn\; c:\Program Files\Microsoft SQL Server\100\Tools\Binn\; c:\Program Files\Microsoft SQL Server\100\DTS\Binn\; C:\Program Files\TortoiseGit\bin; C:\Program Files\Java\jdk1.6.0_26\bin; C:\Program Files\Java\jdk1.6.0_21 ; C:\Program Files\IVI Foundation\VISA\Win64\Bin\; C:\Program Files (x86)\IVI Foundation\VISA\WinNT\Bin\; C:\Program Files (x86)\IVI Foundation\VISA\WinNT\Bin; C:\Program Files\WPIJavaCV\OpenCV_2.2.0\bin; C:\Program Files (x86)\LilyPond\usr\bin; C:\Program Files\TortoiseSVN\bin; C:\Program Files (x86)\doxygen\bin; C:\Program Files (x86)\Graphviz 2.28\bin; C:\Users\Michael\bin\Misc\cppcheck\; C:\Program Files (x86)\Git\cmd; C:\Python27\python.exe; C:\Ruby192\bin; C:\Users\Michael\AppData\Roaming\cabal\bin; C:\Python27\; [EDIT 2] Running python spews this out: 'import site' failed; used -v for traceback Python 2.4.5 (#1, Jul 22 2011, 02:01:04) [GCC 4.1.1] on mingw32 Type "help", "copyright", "credits" or "license" for more information. >>> ...and running python --version (as suggested below) seems to be an unrecognized option. (I also tried running python -v, and it appears that Python 2.4 is trying to import libraries from C:\Python27\Lib, and failed due to a syntax error when it encountered a with statement, which was added in later version, I think) Also, I'm not sure if it's significant or not, but the above python version says something about GCC and mingw32, while running C:\python27\python.exe shows this: Python 2.7.2 (default, Jun 12 2011, 15:08:59) [MSC v.1500 32 bit (Intel)] on win32 Type "help", "copyright", "credits" or "license" for more information. >>>>

    Read the article

  • Unicenter Software Delivery 4 not able to connect to MS SQL 2000 Database after W2003 SP2 upgrade

    - by grub
    Hello Everyone Yesterday I installed the Windows Server 2003 Service Pack 2 on a Windows Server 2003 which has Unicenter Software Delivery 4 installed. Prior to the installation I disabled every CA service on the server (Brightstor, SDO , RCO, TNG) and the MS SQL 2000 service. After the installation of the SP2 I enabled the services again but the Unicenter Service is not able to connect to the MS SQL 2000 Database anymore. The database itself is up and running and I can connect to it with the Enterprise Manager. A dbcc checkdb doesnt return any errors on the Unicenter database. The Unicenter service throws the following error messages during startup: IM[1] 27/05 10:38:31,272 Installation Manager in init phase IM[1] 27/05 10:38:31,694 Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:31,694 sqls error details: IM[1] 27/05 10:38:31,694 (null) IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError C@:TaskmgrL\ASMTML.CXX:596. IM[1] 27/05 10:38:32,069 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:32,069 sqls error details: IM[1] 27/05 10:38:32,069 (null) IM[1] 27/05 10:38:32,069 returned 0. IM[1] 27/05 10:38:32,084 Persistent Storage could not be opened. Error cause is found in the ASM Event Log. Restart Task Manager. IM[1] 27/05 10:38:32,084 Failed to open database. IM[1] 27/05 10:38:32,084 Installation Manager ends> If I check the Unicenter configutation with *chkmib_l* the tool throws an exception and creates a small dump file. An Exception Occurred: Time: 27/05 09:49:38,928 Reason: ChkMIB_l.exe caused an UNKNOWN_EXCEPTION in module kernel32.dll at 7C82001B:77E4BEE7 Registers: EAX=0012F908 EBX=00000000 ECX=00000000 EDX=02410004 ESI=0012F998 EDI=0012F998 EBP=0012F958 ESP=0012F904 EIP=77E4BEE7 FLG=00000206 CS =7C82001B DS =B90023 SS =120023 ES =120023 FS =7C82003B GS =3F0000 Call Stack: 7C82001B:77E4BEE7 (0xE06D7363 0x00000001 0x00000003 0x0012F98C) kernel32.dll 7C82001B:77BB3259 (0x0012F9B8 0x2B017C50 0x2B024404 0x00B68C98) MSVCRT.dll 7C82001B:2B010C42 (0x00020003 0x010C00FE 0x003F0190 0x00B69050) PS.dll << SOFTWARE DELIVERY INSTANCE INFO >> TRIGGER 0(1) instances: JCE 0(1) instances: TM 0(1) instances: IM 0(1) instances: DM 0(1) instances: DPU 0(71) instances: NATF 0(1) instances: MIBCONV 0(0) instances: API 0(4) instances: DTSFT 0(0) instances: TNGPOP 0(0) instances: DGATE 0(0) instances: << FLUSHING MEMORY TRACES >> << STOP FLUSHING MEMORY TRACES >> I compared the configuration of the SDO service and the system configuration with another server on which the Windows Server 2003 SP2 is installed and SDO is working. The configuration is the same and the same driver and software versions are used. Do you have any idea what causes the connection issue? Should I deinstall the unicenter service and make a fresh installation on the server or should I remove the Windows Server 2003 SP2? I don't want to remove the SP2 because it's a requirement for WSUS3 SP2 and I really don't want to know how many possible exploits are possible in such an old system ;-) Thank you very much and have a nice day. Below you can find more detailed information about the system and the SDO service. psinfo output (system information) System information for \\CZZAAS1003: Uptime: 0 days 14 hours 38 minutes 50 seconds Kernel version: Microsoft Windows Server 2003, Multiprocessor Free Product type: Standard Edition Product version: 5.2 Service pack: 2 Kernel build number: 3790 Install date: 23.9.2004, 11:16:11s IE version: 6.0000 System root: C:\WINDOWS Processors: 2 Processor speed: 2.3 GHz Processor type: Intel(R) Xeon(TM) CPU Physical memory: 1024 MB Video driver: RAGE XL PCI Family (Microsoft Corporation) sdver output (Unicenter Software delivery version) Unicenter Software Delivery 4.0 SP1 I2 ENU [2901] Copyright 2004 Computer Associates International, Incorporated ms sql 2000 version and odbc driver version MS SQL 2000 Server Standard Edition Product Version: 8.00.760 (SP3) ODBC Driver: SQL Server - Version 2000.86.3959.00 complete Unicenter Software delivery service log file TRIGGER[1] 27/05 10:38:28,366 SD Trigger Agent has started NATF[1] 27/05 10:38:28,928 Initiation phase finished IM[1] 27/05 10:38:31,272 Installation Manager in init phase IM[1] 27/05 10:38:31,694 Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:31,694 sqls error details: IM[1] 27/05 10:38:31,694 (null) IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError C@:TaskmgrL\ASMTML.CXX:596. IM[1] 27/05 10:38:32,069 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:32,069 sqls error details: IM[1] 27/05 10:38:32,069 (null) IM[1] 27/05 10:38:32,069 returned 0. IM[1] 27/05 10:38:32,084 Persistent Storage could not be opened. Error cause is found in the ASM Event Log. Restart Task Manager. IM[1] 27/05 10:38:32,084 Failed to open database. IM[1] 27/05 10:38:32,084 Installation Manager ends TM[1] 27/05 10:38:32,116 Task Manager in init phase TM[1] 27/05 10:38:32,334 Process TM(L) - [006132] failed to open database SDDATA. dbopen() call failed. TM[1] 27/05 10:38:32,334 sqls error details: TM[1] 27/05 10:38:32,334 (null) TM[1] 27/05 10:38:32,381 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. TM[1] 27/05 10:38:32,381 ##EXCEPTION## TableError C@:TaskmgrL\ASMTML.CXX:596. TM[1] 27/05 10:38:32,381 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process TM(L) - [006132] failed to open database SDDATA. dbopen() call failed. TM[1] 27/05 10:38:32,381 sqls error details: TM[1] 27/05 10:38:32,381 (null) TM[1] 27/05 10:38:32,381 returned 0. TM[1] 27/05 10:38:32,381 Persistent Storage could not be opened. Error cause is found in the ASM Event Log. Restart Task Manager. TM[1] 27/05 10:38:32,381 Failed to open database. TM[1] 27/05 10:38:32,381 Task Manager ends DM[1] 27/05 10:38:33,272 Dialogue Manager is now active API[1] 27/05 10:38:34,397 API Server Process in init phase API[1] 27/05 10:38:34,397 API - SDNLS_Init API[1] 27/05 10:38:34,397 API - connectEM API[1] 27/05 10:38:34,412 API - apiServ.init DM[1] 27/05 10:38:34,678 **AND** 1 Agents triggered API[1] 27/05 10:38:34,709 Process API(L) - [005680] failed to open database SDDATA. dbopen() call failed. API[1] 27/05 10:38:34,709 sqls error details: API[1] 27/05 10:38:34,709 (null) API[1] 27/05 10:38:34,756 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. API[1] 27/05 10:38:34,756 ##EXCEPTION## TableError C@:MainAPIL\APISERVL.CXX:246. API[1] 27/05 10:38:34,756 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process API(L) - [005680] failed to open database SDDATA. dbopen() call failed. API[1] 27/05 10:38:34,756 sqls error details: API[1] 27/05 10:38:34,756 (null) API[1] 27/05 10:38:34,756 returned 0. API[1] 27/05 10:38:34,756 Open of the database failed. API[1] 27/05 10:38:34,756 API - apiServ.init complete API[1] 27/05 10:38:34,756 API - start_APIServer DM[1] 27/05 10:38:34,803 CZZAAR1037 DPU[1:CZZAAR1037] 27/05 10:38:35,772 DPU in init phase DPU[1:CZZAAR1037] 27/05 10:38:36,100 >> GetManagerData DPU[1:CZZAAR1037] 27/05 10:38:36,287 >> SetCompInfo DPU[1:CZZAAR1037] 27/05 10:38:36,334 >> GetContainerList DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6ad DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6ad DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6b7 DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6b7 DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6c1 DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6c1 DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6cb DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6cb DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6f9 DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6f9 DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b71a DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b71a DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b724 DPU[1:CZZAAR1037] 27/05 10:38:36,381 getJobState 3 from 5b724 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b72e DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b72e DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b738 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b738 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b742 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b742 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b74c DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b74c DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b756 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b756 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b78a DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b78a DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b7af DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b7af DPU[1:CZZAAR1037] 27/05 10:38:36,522 >> SetCompAttr DPU[1:CZZAAR1037] 27/05 10:38:36,569 >> SetDetected DPU[1:CZZAAR1037] 27/05 10:38:36,584 disconnect DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6ad DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6b7 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6c1 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6cb DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6f9 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b71a DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b724 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b72e DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b738 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b742 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b74c DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b756 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b78a DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b7af DPU[1:CZZAAR1037] 27/05 10:38:36,584 DPU ends DM[1] 27/05 10:38:38,006 **AND** 0 Agents triggered JCE[1] 27/05 10:38:38,053 JCE starts DM[1] 27/05 10:38:38,287 CZZAAS1003 DPU[2:CZZAAS1003] 27/05 10:38:38,412 DPU in init phase DPU[2:CZZAAS1003] 27/05 10:38:38,647 >> GetManagerData DPU[2:CZZAAS1003] 27/05 10:38:38,756 >> SetCompInfo DPU[2:CZZAAS1003] 27/05 10:38:38,787 >> GetContainerList DM[1] 27/05 10:38:38,850 **AND** 1 Agents triggered DM[1] 27/05 10:38:38,928 CZZAAR1124 DPU[3:CZZAAR1124] 27/05 10:38:39,053 DPU in init phase DPU[3:CZZAAR1124] 27/05 10:38:39,272 >> GetManagerData DM[1] 27/05 10:38:39,334 **AND** 1 Agents triggered DPU[3:CZZAAR1124] 27/05 10:38:39,381 >> SetCompInfo DPU[3:CZZAAR1124] 27/05 10:38:39,412 >> GetContainerList DM[1] 27/05 10:38:39,412 CZZAAR1125 DPU[3:CZZAAR1124] 27/05 10:38:39,428 getJobState 3 from 5b88e DPU[3:CZZAAR1124] 27/05 10:38:39,428 getJobState 3 from 5b88e DPU[2:CZZAAS1003] 27/05 10:38:39,491 >> SetCompAttr DPU[3:CZZAAR1124] 27/05 10:38:39,522 >> SetCompAttr DPU[4:CZZAAR1125] 27/05 10:38:39,522 DPU in init phase DPU[3:CZZAAR1124] 27/05 10:38:39,584 >> SetDetected DPU[2:CZZAAS1003] 27/05 10:38:39,584 >> SetDetected DPU[3:CZZAAR1124] 27/05 10:38:39,584 disconnect DPU[3:CZZAAR1124] 27/05 10:38:39,600 getJobState 3 from 5b88e DPU[3:CZZAAR1124] 27/05 10:38:39,600 DPU ends DPU[2:CZZAAS1003] 27/05 10:38:39,631 disconnect DPU[2:CZZAAS1003] 27/05 10:38:39,631 DPU ends DPU[4:CZZAAR1125] 27/05 10:38:39,756 >> GetManagerData DPU[4:CZZAAR1125] 27/05 10:38:39,850 >> SetCompInfo DPU[4:CZZAAR1125] 27/05 10:38:39,881 >> GetContainerList DPU[4:CZZAAR1125] 27/05 10:38:39,897 getJobState 3 from 5b8a9 DPU[4:CZZAAR1125] 27/05 10:38:39,897 getJobState 3 from 5b8a9 DPU[4:CZZAAR1125] 27/05 10:38:39,991 >> SetCompAttr DPU[4:CZZAAR1125] 27/05 10:38:40,100 >> SetDetected DPU[4:CZZAAR1125] 27/05 10:38:40,116 disconnect DPU[4:CZZAAR1125] 27/05 10:38:40,116 getJobState 3 from 5b8a9 DPU[4:CZZAAR1125] 27/05 10:38:40,116 DPU ends DM[1] 27/05 10:38:40,741 **AND** 0 Agents triggered JCE[1] 27/05 10:38:42,756 JCE ends DM[1] 27/05 10:38:47,475 **AND** 0 Agents triggered DM[1] 27/05 10:38:54,241 **AND** 0 Agents triggered

    Read the article

  • Is it possible to repair a Cisco 3500 XL (3548) switch with POST Error messages?

    - by Alex
    I've got an old Cisco 3500 XL, and it seems to have hardware issues. I've loaded the latest IOS and cleared all config. Does anyone have any experience fixing the switch core? I'm a reasonably competent SMD solderer, can I replace/reflow some chips? I've checked the power supply voltages and it's all within tolerance, and no visible signs of any component damage. Some chips are hot to the touch. I understand that these were EOL as of 2007, but should have a lifetime warranty for the electronics. I don't have a Cisco support contract, so I can't file a ticket. What should I do? Console output: switch: dir flash: Directory of flash:/ 2 -rwx 1811584 <date> c3500xl-c3h2s-mz.120-5.WC17.bin 1799680 bytes available (1812992 bytes used) switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC17.bin"...################################################################################################################################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC17.bin" uncompressed and installed, entry point: 0x3000 executing... Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC17, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2007 by cisco Systems, Inc. Compiled Tue 13-Feb-07 15:04 by antonino Image text-base: 0x00003000, data-base: 0x00352924 Initializing C3500XL flash... flashfs[1]: 1 files, 1 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 3612672 flashfs[1]: Bytes used: 1812992 flashfs[1]: Bytes available: 1799680 flashfs[1]: flashfs fsck took 3 seconds. flashfs[1]: Initialization complete. ...done Initializing C3500XL flash. C3500XL POST: System Board Test: Passed C3500XL POST: Daughter Card Test: Passed C3500XL POST: CPU Buffer Test: Passed C3500XL POST: CPU Notify RAM Test: Passed C3500XL POST: CPU Interface Test: Passed C3500XL POST: Testing Switch Core: Passed Error with Switch Core BIST test Phase 0. Returns: Test Complete Low : 0x0FFFFFFF, Test Complete High : 0xFFFFFFFE Test Phase Low : 0x00000040, Test Phase High : 0x00000000 Test Phase Third : 0x00000000, Test Complete Third : 0x000001F8 C3500XL POST FAILURE: Testing Switch Core: Failed C3500XL POST FAILURE: Testing Buffer Table: Failed C3500XL POST FAILURE: Data Buffer Test: Failed C3500XL POST FAILURE: Configuring Switch Parameters: Failed C3500XL POST FAILURE: Switch Core BIST failed. C3500XL POST FAILURE: Cannot test Modules due to failure of Switch Core POST Del Mar Failure (0th Del Mar): req system failed to init C3500XL POST FAILURE: C3500XL POST FAILURE: ATM: required system failed to init C3500XL POST: Ethernet Controller Test: Passed C3500XL POST FAILURE: MII Test: Failed C3500XL POST FAILURE: Error waiting for Ethernet Controller and SW_PARAMS C3500XL POST FAILURE: Initialization/POST failed C3500XL POST FAILURE: AT: Failing because system POST failed Exception (8192)! Debug Exception (Could be NULL pointer dereference) CPU Register Context: Vector = 0x00002000 PC = 0x000F36F4 MSR = 0x00029200 CR = 0x22000024 LR = 0x000F6964 CTR = 0x001DE46C XER = 0x00000000 R0 = 0x00000000 R1 = 0x004E2580 R2 = 0x00000000 R3 = 0x00000000 R4 = 0x00000001 R5 = 0x00000000 R6 = 0x004E2718 R7 = 0x004E2718 R8 = 0x00000008 R9 = 0x00000000 R10 = 0x0000FFFF R11 = 0x00480000 R12 = 0x42000024 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000 R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19 = 0x00000000 R20 = 0x00000000 R21 = 0x00000000 R22 = 0x00000000 R23 = 0x00000000 R24 = 0x00000000 R25 = 0x00000020 R26 = 0x004E2718 R27 = 0x004E2718 R28 = 0x00000020 R29 = 0x00002513 R30 = 0x00000001 R31 = 0x00000000 Stack trace: PC = 0x000F36F4, SP = 0x004E2580 Frame 00: SP = 0x004E25A0 PC = 0x40000016 Frame 01: SP = 0x004E2618 PC = 0x000F6964 Frame 02: SP = 0x004E26A8 PC = 0x000F76DC Frame 03: SP = 0x004E26C8 PC = 0x000E8114 Frame 04: SP = 0x004E26F0 PC = 0x001F5BF8 Frame 05: SP = 0x004E2710 PC = 0x001F5CF4 Frame 06: SP = 0x004E2748 PC = 0x0023F4DC Frame 07: SP = 0x004E2750 PC = 0x0023E650 Frame 08: SP = 0x004E27C8 PC = 0x0023E89C Frame 09: SP = 0x004E27E0 PC = 0x0028AF34 Frame 10: SP = 0x004E27E8 PC = 0x001E38F8 Frame 11: SP = 0x004E2808 PC = 0x001E39A8 Frame 12: SP = 0x004E2820 PC = 0x0014E220 Frame 13: SP = 0x004E28C8 PC = 0x0014E39C Frame 14: SP = 0x00000000 PC = 0x001EB510

    Read the article

  • Tuning performance of Ubuntu 10.04 on Compaq Evo W4000.

    - by Fantomas
    Hi, I got this computer free and installed Ubuntu 10.04 on it + updates, plus followed the following tutorial all the way: http://www.unixmen.com/linux-tutorials/937-things-to-do-after-installing-ubuntu-1004-lts-lucid-lynx I love the Docky which comes with it, but the computer has been running rather slowly. The System: kernel 2.6.32-22-generic Gnome 2.30.0 (I like Gnome!) Memory: 1GB Processor: Intel (R) Pentium (R) 4 CPU 1700 MHz (needless to say, it is 32 bit). I think I dedicated 128 Mb to video memory while installing, but cannot find this setting now. I did also install an NVidia driver for the 3D card, so I probably want to reclaim that memory back. I want to trim the fat but I also want to keep some of the sex appeal of Ubuntu 10.04. I will gift this computer to a friend, who will use it for Internet, music, videos, word processing, Skype and instant messaging - he is non-technical, so this hardware and Linux should work for him; I just need to speed it up while keeping the good software and having a nice UI. I sort of know my way around Linux, but not that well. Feel free to ask me to run particular commands if you want more info. For starters, here are the services below. Which ones can I kill and how? What else can go? There is no need to run ssh or ftp or http or ntp servers. As I said before, this computer is for non-technical person. There is also absolutely no bluetooth or wireless networking needed - it will feed off a regular ethernet cable. What I do not want to do is reinstall some other distro or recompile a kernel. I want to make it 80% perfect spending 20% of the energy :) Thanks! $ service --status-all [ ? ] acpi-support [ ? ] acpid [ ? ] alsa-mixer-save [ ? ] anacron [ - ] apparmor [ ? ] apport [ ? ] atd [ ? ] avahi-daemon [ ? ] binfmt-support [ - ] bluetooth [ - ] bootlogd [ - ] brltty [ ? ] console-setup [ ? ] cron [ + ] cups [ ? ] dbus [ ? ] dmesg [ ? ] dns-clean [ ? ] failsafe-x [ - ] fancontrol [ ? ] gdm [ - ] grub-common [ ? ] hostname [ ? ] hwclock [ ? ] hwclock-save [ ? ] irqbalance [ - ] kerneloops [ ? ] killprocs [ - ] lm-sensors [ ? ] module-init-tools [ ? ] network-interface [ ? ] network-interface-security [ ? ] network-manager [ ? ] networking [ ? ] ondemand [ ? ] pcmciautils [ ? ] plymouth [ ? ] plymouth-log [ ? ] plymouth-splash [ ? ] plymouth-stop [ ? ] pppd-dns [ ? ] procps [ + ] pulseaudio [ ? ] rc.local [ - ] rsync [ ? ] rsyslog [ - ] saned [ ? ] screen-cleanup [ ? ] sendsigs [ ? ] speech-dispatcher [ ? ] stop-bootlogd [ ? ] stop-bootlogd-single [ ? ] udev [ ? ] udev-finish [ ? ] udevmonitor [ ? ] udevtrigger [ ? ] ufw [ ? ] umountfs [ ? ] umountnfs.sh [ ? ] umountroot [ ? ] unattended-upgrades [ - ] urandom [ + ] winbind [ ? ] wpa-ifupdown [ - ] x11-common

    Read the article

  • unable to sniff traffic despite network interface being in monitor or promiscuous mode

    - by user65126
    I'm trying to sniff out my network's wireless traffic but am having issues. I'm able to put the card in monitor mode, but am unable to see any traffic except broadcasts, multicasts and probe/beacon frames. I have two network interfaces on this laptop. One is connected normally to 'linksys' and the other is in monitor mode. The interface in monitor mode is on the right channel. I'm not associated with the access point because, as I understand, I don't need to if using monitor mode (vs promiscuous). When I try to ping the router ip, I'm not seeing that traffic show up in wireshark. Here's my ifconfig settings: daniel@seasonBlack:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:29:9e:b2:89 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8518 (8.5 KB) TX bytes:8518 (8.5 KB) wlan0 Link encap:Ethernet HWaddr 00:21:00:34:f7:f4 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:ff:fe34:f7f4/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:9758 errors:0 dropped:0 overruns:0 frame:0 TX packets:4869 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3291516 (3.2 MB) TX bytes:677386 (677.3 KB) wlan1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-33-34-00-00-00-00-00-00-00-00 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:1500 Metric:1 RX packets:112754 errors:0 dropped:0 overruns:0 frame:0 TX packets:101 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18569124 (18.5 MB) TX bytes:12874 (12.8 KB) wmaster0 Link encap:UNSPEC HWaddr 00-21-00-34-F7-F4-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Here's my iwconfig settings: daniel@seasonBlack:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:F8:D6:17:34 Bit Rate=54 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=68/70 Signal level=-42 dBm Noise level=-69 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wmaster1 no wireless extensions. wlan1 IEEE 802.11bg Mode:Monitor Frequency:2.437 GHz Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Here's how I know I'm on the right channel: daniel@seasonBlack:~$ iwlist channel lo no frequency information. eth0 no frequency information. wmaster0 no frequency information. wlan0 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6) wmaster1 no frequency information. wlan1 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6)

    Read the article

  • Fix overscan in Linux with Intel graphics Vizio HDTV

    - by Padenton
    I am connecting my server to my HDTV so that I can conveniently display it there. My VIZIO HDTV cuts off all 4 edges. I already realize it is not optimal to be running a GUI on a server; this server will not have much external traffic so I prefer it for convenience. I have already spent countless hours searching for a fix, but all I could find required an ATI or NVIDIA graphics card, or didn’t work. In Windows, the Intel driver has a setting for underscan, though it seems only to be available by a glitch. Here’s my specs: Ubuntu Linux (Quantal 12.10) (Likely to switch to Arch) This is a home server computer, with KDE for managing(for now, at least) Graphics: Intel HD Graphics 4000 from Ivy Bridge Motherboard: ASRock Z77 Extreme4 CPU: Intel Core i5-3450 My monitors: Dell LCD monitor Vizio VX37L_HDTV10A 37" on HDMI input I have tried all of the following from both HDMI?HDMI and DVI?HDMI cables connected to the ports on my motherboard: Setting properties in xrandr Making sure drivers are all up to date Trying several different modes The TV was “cheap”; max resolution 1080i. I am able to get a 1920x1080 modeline, in both GNU/Linux and Windows, without difficulty. There is no setting in the menu to fix the overscan (I have tried all of them, I realize it’s not always called overscan). I have been in the service menu for the TV, which still does not contain an option to fix it. No aspect ratio settings, etc. The TV has a VGA connector but I am unsure if it would fix it, as I don’t have a VGA cable long enough, and am not sure it would get me the 1920x1080 resolution which I want. Using another resolution does not fix the problem. I tried custom modelines with the dimensions of my screen’s viewable area, but it wouldn’t let me use them. Ubuntu apparently doesn’t automatically generate an xorg.conf file for use. I read somewhere that modifying it may help solve it. I tried X -configure several times(with reboots, etc.) but it consistently gave the following error messages: In log file: … (WW) Falling back to old probe method for vesa Number of created screens does not match number of detected devices. Configuration failed. In output: … (++) Using config file: "/root/xorg.conf.new" (==) Using system config directory "/usr/share/X11/xorg.conf.d" Number of created screens does not match number of detected devices. Configuration failed. Server terminated with error (2). Closing log file. Tried using 'overscan' prop in xrandr: root@xxx:/home/xxx# xrandr --output HDMI1 --set overscan off X Error of failed request: BadName (named color or font does not exist) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 11 (RRQueryOutputProperty) Serial number of failed request: 42 Current serial number in output stream: 42 'overscan on', 'underscan off', 'underscan on' were all also tried. Originally tried with Ubuntu 12.04, but failed and so updated to 12.10 when it was released. All software is up to date. I am not opposed to reinstalling my OS, likely will anyways (my preference being Arch).

    Read the article

  • compile lastest bnx2 driver on debian squeeze

    - by markus
    I want to upgrade the bnx2 network card driver in a Dell Power Edge R410. I downloaded the latest driver version from the broadcom website. If I want to compile the driver it fails with the following errors: make make -C bnx2/src KVER=2.6.32-5-amd64 PREFIX= make[1]: Entering directory `/tmp/netxtreme2-6.2.23/bnx2-2.0.23b/src' make -C /lib/modules/2.6.32-5-amd64/build SUBDIRS=/tmp/netxtreme2-6.2.23/bnx2-2.0.23b/src modules make[2]: Entering directory `/usr/src/linux-headers-2.6.32-5-amd64' Building modules, stage 2. MODPOST 2 modules make[2]: Leaving directory `/usr/src/linux-headers-2.6.32-5-amd64' make[1]: Leaving directory `/tmp/netxtreme2-6.2.23/bnx2-2.0.23b/src' make -C bnx2x/src KVER=2.6.32-5-amd64 PREFIX= make[1]: Entering directory `/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src' make -C /lib/modules/2.6.32-5-amd64/build M=`pwd` modules make[2]: Entering directory `/usr/src/linux-headers-2.6.32-5-amd64' CC [M] /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.o In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1009:1: error: "PCI_VPD_LRDT_ID_STRING" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1327:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1011:1: error: "PCI_VPD_LRDT_RO_DATA" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1328:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1013:1: error: "PCI_VPD_LRDT_RW_DATA" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1329:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1019:1: error: "PCI_VPD_SRDT_END" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1334:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1032: error: conflicting types for ‘pci_vpd_lrdt_size’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1355: error: previous definition of ‘pci_vpd_lrdt_size’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1037: error: conflicting types for ‘pci_vpd_srdt_size’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1366: error: previous definition of ‘pci_vpd_srdt_size’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1042: error: conflicting types for ‘pci_vpd_find_tag’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1391: error: previous declaration of ‘pci_vpd_find_tag’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1077: error: conflicting types for ‘pci_vpd_info_field_size’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1377: error: previous definition of ‘pci_vpd_info_field_size’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1082: error: conflicting types for ‘pci_vpd_find_info_keyword’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1403: error: previous declaration of ‘pci_vpd_find_info_keyword’ was here make[5]: *** [/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.o] Fehler 1 make[4]: *** [_module_/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src] Fehler 2 make[3]: *** [sub-make] Fehler 2 make[2]: *** [all] Fehler 2 make[2]: Leaving directory `/usr/src/linux-headers-2.6.32-5-amd64' make[1]: *** [bnx2x.o] Fehler 2 make[1]: Leaving directory `/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src' make: *** [l2build] Fehler 2

    Read the article

  • Bridged virtual interface is not available or visible to ifconfig.

    - by Omniwombat
    Hello all. I'm running Ubuntu 9.04, kernel 2.6.28-18, and vmware-server 2.0.1. I'm attempting to setup a virtual linux machine to use a bridged interface rather than NAT or host-only. Both NAT and host-only work just fine. When running vmware-config.pl, I set /dev/vmnet0 to bridge eth0, /dev/vmnet1 to host-only, and /dev/vmnet8 to NAT. When I run ifconfig -a I see the physical interface (eth0), vmnet1 and vmnet8 both of which are up and have IP addresses assigned to them. I also see other various interfaces that are not relevant here. In the web console, when I ask that the guest machine's network card be bridged, it states that a bridged setup is "Not available" and shows the disabled device icon. Inside the guest machine, I do have an eth0 interface which I can set to anything I like, however it can't see my external network, or the host. I do see errors in my vmware/hostd.log which state: "The network bridge on device vmnet0 is not running. The virtual machine will not be able to communicate with the host or with other machines on your network" which confirms the problem. vmnet-bridge is running, and I see the following in my process table: /usr/bin/vmnet-bridge -d /var/run/vmnet-bridge-0.pid -n 0 -i eth0 I confirm that the /var/run/vmnet-bridge-0.pid file is there and that it points to the correct process. I saw this question relating to Ubuntu 9.04 and bridged interfaces, in which the poster determined that the vsock library was not getting built due to a flaw in the vmware-config.pl script. I applied the patch, reran the script, and confirm that vsock.ko and vsock.o are in my /lib directory structure. vsock does show up in an lsmod. My /etc/vmware directory has /vmnet1 and /vmnet8 subdirectories. They contain configuration utilities for running DHCP and nat type services as expected. There is no vmnet0 subdirectory. My /etc/vmware/netmap.conf file DOES show entries for vmnet0; both the name and the device as I configured it from the script. My /dev directory contains devices vmnet0 through vmnet9. They have major device number 119, and minor device numbers 0 through 9. /proc/net/dev shows statistics for vmnet1 and vmnet8, but not vmnet0. I have a /proc/vmnet directory, but it's empty. When I start or stop the vmware service with /etc/init.d/vmware start, I see the following: Starting VMware services: Virtual machine monitor done Virtual machine communication interface done VM communication interface socket family: done Virtual ethernet done Bridged networking on /dev/vmnet0 done Host-only networking on /dev/vmnet1 (background) done DHCP server on /dev/vmnet1 done Host-only networking on /dev/vmnet8 (background) done DHCP server on /dev/vmnet8 done NAT service on /dev/vmnet8 done VMware Server Authentication Daemon (background) done Shared Memory Available done Starting VMware management services: VMware Server Host Agent (background) done VMware Virtual Infrastructure Web Access Starting VMware autostart virtual machines: Virtual machines done Nothing appears to be wrong there. What n00b thing am I doing such that vmnet0 and only vmnet0 does not show up in the interface list?

    Read the article

  • Linux Kernel not passing through multicast UDP packets

    - by buecking
    Recently I've set up a new Ubuntu Server 10.04 and noticed my UDP server is no longer able to see any multicast data sent to the interface, even after joining the multicast group. I've got the exact same set up on two other Ubuntu 8.04.4 LTS machines and there is no problem receiving data after joining the same multicast group. The ethernet card is a Broadcom netXtreme II BCM5709 and the driver used is: b $ ethtool -i eth1 driver: bnx2 version: 2.0.2 firmware-version: 5.0.11 NCSI 2.0.5 bus-info: 0000:01:00.1 I'm using smcroute to manage my multicast registrations. b$ smcroute -d b$ smcroute -j eth1 233.37.54.71 After joining the group ip maddr shows the newly added registration. b$ ip maddr 1: lo inet 224.0.0.1 inet6 ff02::1 2: eth0 link 33:33:ff:40:c6:ad link 01:00:5e:00:00:01 link 33:33:00:00:00:01 inet 224.0.0.1 inet6 ff02::1:ff40:c6ad inet6 ff02::1 3: eth1 link 01:00:5e:25:36:47 link 01:00:5e:25:36:3e link 01:00:5e:25:36:3d link 33:33:ff:40:c6:af link 01:00:5e:00:00:01 link 33:33:00:00:00:01 inet 233.37.54.71 <------- McastGroup. inet 224.0.0.1 inet6 ff02::1:ff40:c6af inet6 ff02::1 So far so good, I can see that I'm receiving data for this multicast group. b$ sudo tcpdump -i eth1 -s 65534 host 233.37.54.71 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth1, link-type EN10MB (Ethernet), capture size 65534 bytes 09:30:09.924337 IP 192.164.1.120.58848 > 233.37.54.71.15572: UDP, length 212 09:30:09.947547 IP 192.164.1.120.58848 > 233.37.54.71.15572: UDP, length 212 09:30:10.108378 IP 192.164.1.120.58866 > 233.37.54.71.15574: UDP, length 268 09:30:10.196841 IP 192.164.1.120.58848 > 233.37.54.71.15572: UDP, length 212 ... I can also confirm that the interface is receiving mcast packets. b $ ethtool -S eth1 | grep mcast_pack rx_mcast_packets: 103998 tx_mcast_packets: 33 Now here's the problem. When I try to capture the traffic using a simple ruby UDP server I receive zero data! Here's a simple server that reads data send on port 15572 and prints the first two characters. This works on the two 8.04.4 Ubuntu Servers, but not the 10.04 server. require 'socket' s = UDPSocket.new s.bind("", 15572) 5.times do text, sender = s.recvfrom(2) puts text end If I send a UDP packet crafted in ruby to localhost, the server receives it and prints out the first two characters. So I know that the server above is working correctly. irb(main):001:0> require 'socket' => true irb(main):002:0> s = UDPSocket.new => #<UDPSocket:0x7f3ccd6615f0> irb(main):003:0> s.send("I2 XXX", 0, 'localhost', 15572) When I check the protocol statistics I see that InMcastPkts is not increasing. While on the other 8.04 servers, on the same network, received a few thousands packets in 10 seconds. b $ netstat -sgu ; sleep 10 ; netstat -sgu IcmpMsg: InType3: 11 OutType3: 11 Udp: 446 packets received 4 packets to unknown port received. 0 packet receive errors 461 packets sent UdpLite: IpExt: InMcastPkts: 4654 <--------- Same as below OutMcastPkts: 3426 InBcastPkts: 9854 InOctets: -1691733021 OutOctets: 51187936 InMcastOctets: 145207 OutMcastOctets: 109680 InBcastOctets: 1246341 IcmpMsg: InType3: 11 OutType3: 11 Udp: 446 packets received 4 packets to unknown port received. 0 packet receive errors 461 packets sent UdpLite: IpExt: InMcastPkts: 4656 <-------------- Same as above OutMcastPkts: 3427 InBcastPkts: 9854 InOctets: -1690886265 OutOctets: 51188788 InMcastOctets: 145267 OutMcastOctets: 109712 InBcastOctets: 1246341 If I try forcing the interface into promisc mode nothing changes. At this point I'm stuck. I've confirmed the kernel config has multicast enabled. Perhaps there are other config options I should be checking? b $ grep CONFIG_IP_MULTICAST /boot/config-2.6.32-23-server CONFIG_IP_MULTICAST=y Any thoughts on where to go from here?

    Read the article

  • Application Does Not Start in Windows 7

    - by Jim Fell
    I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fresh from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried running sfc /scannow from the command line (with administrator privileges), shutting down the Spybot Resident, and disabling the firewall and virus scanner. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Faulting application name: SSDFresh.exe, version: 1.0.0.0, time stamp: 0x4f2a45d8 Faulting module name: unknown, version: 0.0.0.0, time stamp: 0x00000000 Exception code: 0xc0000005 Fault offset: 0x000007ff0016dbba Faulting process id: 0x994 Faulting application start time: 0x01cd11fd9fe978df Faulting application path: C:\Program Files (x86)\SSD Fresh\SSDFresh.exe Faulting module path: unknown Report Id: dfeed551-7df0-11e1-a2c7-002522c47ec0 Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Application: SSDFresh.exe Framework Version: v4.0.30319 Description: The process was terminated due to an unhandled exception. Exception Info: System.NullReferenceException Stack: at AbBugReporter.BugForm.InitLanguage() at AbBugReporter.BugForm..ctor(AbFlexTrans.LanguageInfo, AbBugReporter.BugReportManager, Boolean) at AbBugReporter.BugReportManager.Show(System.Exception) at SSDFresh.App.App_DispatcherUnhandledException(System.Object, System.Windows.Threading.DispatcherUnhandledExceptionEventArgs) at System.Windows.Threading.Dispatcher.CatchException(System.Exception) at MS.Internal.Threading.ExceptionFilterHelper.TryCatchWhen(System.Object, System.Delegate, System.Object, Int32, System.Delegate) at System.Windows.Threading.Dispatcher.WrappedInvoke(System.Delegate, System.Object, Int32, System.Delegate) at System.Windows.Threading.Dispatcher.InvokeImpl(System.Windows.Threading.DispatcherPriority, System.TimeSpan, System.Delegate, System.Object, Int32) at MS.Win32.HwndSubclass.SubclassWndProc(IntPtr, Int32, IntPtr, IntPtr) at MS.Win32.UnsafeNativeMethods.DispatchMessage(System.Windows.Interop.MSG ByRef) at System.Windows.Threading.Dispatcher.PushFrameImpl(System.Windows.Threading.DispatcherFrame) at System.Windows.Application.RunInternal(System.Windows.Window) at System.Windows.Application.Run() at SSDFresh.App.Main() Error 4/2/2012 11:35:39 PM SideBySide 59 None Activation context generation failed for "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\csc.exe".Error in manifest or policy file "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\csc.exe.Config" on line 0. Invalid Xml syntax. Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

    Read the article

  • SSH Public Key Authentication only works if active session exists before

    - by Webx10
    I have a rather strange problem with my SSH configuration. I set up my server with the help of a Remote Access Card and configured everything with a KVM viewer. So while being logged into the server via the KVM Viewer I configured SSH with only pubkey and tried to login from my local laptop. It worked fine. If I quit the KVM Session (or logout with the user in the KVM session) I cannot login via ssh anymore (pubkey denied). SSH login only works as long as the user is somewhere still logged in. Any hints what the problem might be? Console output for a failed login (all personal data exchanged): OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /Users/mylocaluser/.ssh/config debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 103: Applying options for * debug1: Connecting to 100.100.100.100 [100.100.100.100] port 12345. debug1: Connection established. debug1: identity file /Users/mylocaluser/.ssh/id_rsa type 1 debug1: identity file /Users/mylocaluser/.ssh/id_rsa-cert type -1 debug1: identity file /Users/mylocaluser/.ssh/id_dsa type -1 debug1: identity file /Users/mylocaluser/.ssh/id_dsa-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.2 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.6.1p1 Ubuntu-2ubuntu2 debug1: match: OpenSSH_6.6.1p1 Ubuntu-2ubuntu2 pat OpenSSH* debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr [email protected] none debug1: kex: client->server aes128-ctr [email protected] none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA ab:12:23:34:45:56:67:78:89:90:12:23:34:45:56:67 debug1: Host '[100.100.100.100]:12345' is known and matches the RSA host key. debug1: Found key in /Users/mylocaluser/.ssh/known_hosts:36 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/mylocaluser/.ssh/id_rsa debug1: Authentications that can continue: publickey debug1: Offering RSA public key: /Users/mylocaluser/.ssh/id_rsa2 debug1: Authentications that can continue: publickey debug1: Trying private key: /Users/mylocaluser/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey). Console output for a successfull login (only possible while "active session" exists): OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /Users/mylocaluser/.ssh/config debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 103: Applying options for * debug1: Connecting to 100.100.100.100 [100.100.100.100] port 12345. debug1: Connection established. debug1: identity file /Users/mylocaluser/.ssh/id_rsa type 1 debug1: identity file /Users/mylocaluser/.ssh/id_rsa-cert type -1 debug1: identity file /Users/mylocaluser/.ssh/id_dsa type -1 debug1: identity file /Users/mylocaluser/.ssh/id_dsa-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.2 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.6.1p1 Ubuntu-2ubuntu2 debug1: match: OpenSSH_6.6.1p1 Ubuntu-2ubuntu2 pat OpenSSH* debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr [email protected] none debug1: kex: client->server aes128-ctr [email protected] none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA ab:12:23:34:45:56:67:78:89:90:12:23:34:45:56:67 debug1: Host '[100.100.100.100]:12345' is known and matches the RSA host key. debug1: Found key in /Users/mylocaluser/.ssh/known_hosts:36 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/mylocaluser/.ssh/id_rsa debug1: Server accepts key: pkalg ssh-rsa blen 279 debug1: Authentication succeeded (publickey). Authenticated to 100.100.100.100 ([100.100.100.100]:12345). debug1: channel 0: new [client-session] debug1: Requesting [email protected] debug1: Entering interactive session. debug1: Sending environment. debug1: Sending env LANG = de_DE.UTF-8 Welcome to Ubuntu 14.04.1 LTS

    Read the article

  • hostapd running on Ubuntu Server 13.04 only allows single station to connect when using wpa

    - by user450688
    Problem Only a single station can connect to hostapd at a time. Any single station can connect (W8, OSX, iOS, Nexus) but when two or more hosts are connected at the same time the first client loses its connectivity. However there are no connectivity issues when WPA is not used. Setup Linux (Ubuntu server 13.04) wireless router (with separate networks for wired WAN, wired LAN, and Wireless LAN. iptables-save output: *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.0.0/24 -o p4p1 -j MASQUERADE -A POSTROUTING -s 10.0.1.0/24 -o p4p1 -j MASQUERADE COMMIT *mangle :PREROUTING ACCEPT [13:916] :INPUT ACCEPT [9:708] :FORWARD ACCEPT [4:208] :OUTPUT ACCEPT [9:3492] :POSTROUTING ACCEPT [13:3700] COMMIT *filter :INPUT DROP [0:0] :FORWARD DROP [0:0] :OUTPUT ACCEPT [9:3492] -A INPUT -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -i p4p1 -p tcp -m tcp --dport 22 -m state --state NEW -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i wlan0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A FORWARD -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -i eth0 -j ACCEPT -A FORWARD -i wlan0 -j ACCEPT -A FORWARD -i lo -j ACCEPT COMMIT /etc/hostapd/hostapd.conf #Wireless Interface interface=wlan0 driver=nl80211 ssid=<removed> hw_mode=g channel=6 max_num_sta=15 auth_algs=3 ieee80211n=1 wmm_enabled=1 wme_enabled=1 #Configure Hardware Capabilities of Interface ht_capab=[HT40+][SMPS-STATIC][GF][SHORT-GI-20][SHORT-GI-40][RX-STBC12] #Accept all MAC address macaddr_acl=0 #Shared Key Authentication wpa=1 wpa_passphrase=<removed> wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ###IPad Connectivevity Repair ieee8021x=0 eap_server=0 Wireless Card #lshw output product: RT2790 Wireless 802.11n 1T/2R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 00 serial: <removed> width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=rt2800pci driverversion=3.8.0-25-generic firmware=0.34 ip=10.0.1.254 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn #iw list output Band 1: Capabilities: 0x272 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI RX STBC 2-streams Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 2 usec (0x04) HT RX MCS rate indexes supported: 0-15, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (27.0 dBm) * 2417 MHz [2] (27.0 dBm) * 2422 MHz [3] (27.0 dBm) * 2427 MHz [4] (27.0 dBm) * 2432 MHz [5] (27.0 dBm) * 2437 MHz [6] (27.0 dBm) * 2442 MHz [7] (27.0 dBm) * 2447 MHz [8] (27.0 dBm) * 2452 MHz [9] (27.0 dBm) * 2457 MHz [10] (27.0 dBm) * 2462 MHz [11] (27.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ AP } <= 8, total <= 8, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * set_tx_bitrate_mask * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (84) * Unknown command (87) * Unknown command (85) * Unknown command (89) * Unknown command (92) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * Unknown mode (10): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0x40 0xb0 0xc0 0xd0 * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * Unknown mode (10): 0x40 0xd0 Device supports RSN-IBSS. HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS.

    Read the article

  • How to get ISA 2006 Web Proxy to work with the Single Network Adapter template

    - by tronda
    I need to test an issue with running our application behind a proxy server with different type of configurations, so I installed ISA 2006 Enterprise on a desktop computer. Since this computer only has a single network card and I want to start out easy, I chose the "Single Network Adapter" template. We have a internal NAT'ed network which is in the 10 range. I have defined the internal network on the ISA server to be 10.XXX.YY.1 - 10.XXX.YY.255 I also have the Default rule which denies all traffic, but I've added the following Rule: Policy - Protocols - From - To Accept HTTP Internal External HTTPS Local Host Internal HTTS Server Localhost Then I configured Internet Explorer on a virutal machine running XP within virtualbox with Brigded network (gets same network address range as regular computers on our network) similar to this Instead of the server name I used the IP address. When I try to access a web page, this doesn't go through and I get the following log messages on the proxy server: Original Client IP Client Agent Authenticated Client Service Referring Server Destination Host Name Transport HTTP Method MIME Type Object Source Source Proxy Destination Proxy Bidirectional Client Host Name Filter Information Network Interface Raw IP Header Raw Payload GMT Log Time Source Port Processing Time Bytes Sent Bytes Received Cache Information Error Information Authentication Server Log Time Client IP Destination IP Destination Port Protocol Action Rule Result Code HTTP Status Code Client Username Source Network Destination Network URL Server Name Log Record Type 10.XXX.YY.174 - TCP - - - 24.08.2010 13:25:24 1080 0 0 0 0x0 0x0 - 24.08.2010 06:25:24 10.XXX.YY.174 10.XXX.YY.175 80 HTTP Initiated Connection MyHTTPAccess 0x0 ERROR_SUCCESS Internal Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:24 2275 0 0 0 0x0 0x0 - 24.08.2010 06:25:24 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:25 2275 0 0 0 0x0 0x0 - 24.08.2010 06:25:25 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:25 2276 0 0 0 0x0 0x0 - 24.08.2010 06:25:25 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:26 2276 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:26 2277 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.159 - UDP - - - 24.08.2010 13:25:26 68 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.159 255.255.255.255 67 DHCP (request) Denied Connection [Enterprise] Default rule 0xc004000d FWX_E_POLICY_RULES_DENIED Internal Local Host - PROXYTEST Firewall 10.XXX.YY.166 - UDP - - - 24.08.2010 13:25:26 68 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.166 255.255.255.255 67 DHCP (request) Denied Connection [Enterprise] Default rule 0xc004000d FWX_E_POLICY_RULES_DENIED Internal Local Host - PROXYTEST Firewall 0.0.0.0 Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Yes Proxy 10.XXX.YY.175 TCP GET Internet - - - Req ID: 096c76ae; Compression: client=No, server=No, compress rate=0% decompress rate=0% - - - 24.08.2010 13:25:27 0 2945 2581 446 0x0 0x40 24.08.2010 06:25:27 10.XXX.YY.174 10.XXX.YY.175 80 http Failed Connection Attempt MyHTTPAccess 10061 anonymous Internal Local Host http://www.vg.no/ PROXYTEST Web Proxy Filter 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:27 2277 0 0 0 0x0 0x0 - 24.08.2010 06:25:27 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall

    Read the article

  • Asus P8P67 Rev. 3.1 Motherboard issues powering on and saving settings

    - by Scott
    Edit: New Information Have some updated information from the old question below: So basically my issue right now is somewhat similar, but I've been able to rule out a couple of things. I don't think this has anything to do with light on the motherboard. No matter what lights are on/off on the motherboard when the computer is off, they don't affect this issue. The main power LED on the Mobo is always lit when the power supply is turned on, and that's what matters anyway. Even when the main power LED is on, the PC will NOT boot up the first time I hit the power switch. I have to go reset the power supply (make all lights turn off on the Mobo and back on), and THEN hit the power switch. Then everything boots up. Also, the BIOS settings are reset every time this happens. Asus Tech Support told me to try jumping the power with something metal to try and rule out that it's a problem with the connectors getting power, or if it's a problem with the case power switch pins - haven't done that yet though. Any ideas? This is a lot simpler than it was before when I thought it had to do with certain LED indicators for RAM, EPU, etc. Original Question So I built my new desktop just about 3 weeks ago. I've been having a few issues which I think are all related to my motherboard, an Asus P8P67 Revision 3.1, but I'm not 100% sure as this is really the first from-scratch build I've ever done. I've posted these questions on the Asus forums, Asus Tech Support, and the Corsair forums as well as I thought it might have something to do with my power supply at one point. None of these avenues have solved my issue until now completely, so I thought I'd come here to see what you guys think. Here's what's happening: My computer is off, and I go to power it on. I press the power switch on the case (Antec Nine Hundred), and nothing seems to happen. Upon further inspection, I see that what this actually does is simply turn on the EPU LED on my motherboard, but doesn't actually boot anything up. I then have to go and flip the main power switch on the power supply off and back on. What this does is turn off all lights on the Motherboard after a few seconds, and turn them all back on (including the EPU LED that was off before I hit the power switch the first time). Now, hitting the power switch works. The machine boots up fine, and starts going through the boot up process. As a side note: My Motherboard is set to "Force BIOS", and every single time I change this to do the opposite, the next time my computer boots up that change reverts itself. I think this may be due to the fact that I am doing the hard reset on the power supply each time, but I'm not sure. I had thought that the Motherboard would keep its BIOS settings unless you did something to the Mobo itself - so this may be a related issue, or something else completely. That's basically it. Once it's on, it's on. It works fine, recognizes all of my hardware, and runs great. All fans/lights in the case work great, and I'm getting standard readings. The next time I go to shut the computer down however, I can expect the same exact process getting it up and running, including being forced to go into BIOS and exit again before I can load Windows. Another side note: If I power on my computer using the power switch DIRECTLY after shutting it down, it powers right back on (I think this is because the EPU LED light doesn't have time to turn off). It looks as if as long as the EPU LED is lit up on the motherboard before I hit the power switch on the case, the thing will boot up fine (although this doesn't explain the "Force BIOS" issue, at least it's something). Any ideas? Thanks guys. P.S. - System Specs Asus P8P67 Rev. 3.1 Motherboard Intel Core i7 2600K Processor 16GB (4x4GB) G-Skill 1600 RAM NVIDIA EVGA GTX 570 Video Card Crucial 128GB SSD HD Corsair 850W Power Supply Seagate 2TB HDD

    Read the article

  • Dell Latitude E6430 Docking Station + Dual Monitor + Laptop Screen Tri-Monitor setup

    - by Larry
    I have a company issued laptop and docking station as well as two monitors The specifications of the hardware are as follows; Laptop: Latitude E6430 BIOS: A02.00 Processor: i7-3720QM CPU @ 2.60 (8 CPUs) Memory: 4096MB RAM Page file: 1825MB used, 4793MB available DirectX 11 Display Driver/Chip: MVIDIA NVS 5200M DAC: Integrated RAMDAC Aprox Total Memory: 2376 (Above 3 details same for both displays) Current Display Mode (Display 1): 1600x900 Current Display Mode (Display 2): 1440x900 the docking station is a Dell Latitude E6420 Docking Station PR03X Port Replicator and I don't think the monitor model is particularly relevant to resolving this issue but they are both Acer V193Ws The story goes like this; the laptop works fine if I VGA one monitor into the laptop through the vga port on the back of the lefthand side of the laptop I can achieve dual monitor display fine (laptop screen + monitor) if I plug the laptop into the docking station and use the vga port in the back of the docking station I can dual monitor fine (laptop screen + monitor) if I plug the laptop into the docking station, the laptop's lefthand side VGA port no longer seems to function at all I've spoken to internal IT about this issue and they're going to get me some kind of VGA splitter or a DVI-VGA adapter to use with the docking station for the second Acer Monitor, but that isn't going to happen for a few days. So I guess what I'm wondering is; is there any way to continue to use the side VGA port on my laptop while using the docking station VGA port? and as a secondary 'followup' pending resolution of the initial issue with getting both monitors up and running (at the moment I have both monitors on my desk but am just using my laptop screen as one of my dual monitor display with one of the monitors [the one connected to dock]), is there any way to CONTINUE to use my laptop monitor to in effect have a triple monitor display (2 monitors + docked laptop)? I am wondering this because internal IT told me that they were aware of some issues with the particular display drivers in my box and triple monitor displays but weren't really going to look TOO much in-depth into that (which is perfectly understandable) since getting the adapter for the dual monitors up and running was the greater priority within their purview. So this is a two parter; Can I dual monitor using two vga cables with 1 docking station vga port and one laptop vga port? is there a setting that can be tweaked somewhere? because plugging the box into the station seems to make the side port stop working and... Is there any reasonably simple and cost-effective work around (e.g. I am find with shelling out maybe a few dollars out of my own pocket for some hardware or software to make my company box tri-display capable) but if this requires some extensive rebuild or new OSs or doing stuff to the BIOS I'd rather have a straight answer about this being untenable as a slight modification to a (once again) company laptop and stop wasting time looking into it Thanks! and please let me know if you guys need any more details (tech specs or something) to answer this question [EDIT] 2/10/2014 Just an update; turned out it really was just a hardware limitation issue. The old laptop just couldn't hack it. Got a new laptop with a better video card and different monitors from my company and am successfully using a triple display currently (2 monitors + laptop screen)

    Read the article

  • Setup access to SAS RAID drives with NTFS partitions on CentOS Machine

    - by Quanano
    We have a Dell Poweredge 2900 system with Adaptec 39320A SCSI CONTROLLER CARD and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on the other raid array with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log

    Read the article

  • Postfix not sending/allowing receiving of messages after server (hardware) changed

    - by 537mfb
    We had na old notebook runing Ubuntu 12.04 working as a web/ftp/mail server and it worked but since the notebook was a notebook and pretty old and unreliable, a desktop was bought to replace it before it stopped working all together. Due to issues with the new desktop's vídeo card, we couldn't use Ubuntu 12.04 so we installed Ubuntu 13.10 and wen't about configuring it. Since we removed the notebook from the network, we kept the same Computer Name and local IP address to make things as close to the old server as possible configuration-wise. However, something has gone wrong since Postfix is throwing error 451 4.3.0 lookup faillure on every attempt to send a mail, and no email can be received either. Our main.cf file is a copy of the one we were using (and working) on the old server (notice we use EHCP) # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name powered by Easy Hosting Control Panel (ehcp) on Ubuntu, www.ehcp.net biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no myhostname = m21-traducoes.com.pt relayhost = mydestination = localhost, 89.152.248.139 mynetworks = 127.0.0.0/8, 192.168.0.0/16, 172.16.0.0/16, 10.0.0.0/8, 89.152.248.0/24 virtual_alias_domains = virtual_alias_maps = proxy:mysql:/etc/postfix/mysql-virtual_forwardings.cf, proxy:mysql:/etc/postfix/mysql-virtual_email2email.cf transport_maps = proxy:mysql:/etc/postfix/mysql-virtual_transports.cf virtual_mailbox_domains = proxy:mysql:/etc/postfix/mysql-virtual_domains.cf virtual_mailbox_maps = proxy:mysql:/etc/postfix/mysql-virtual_mailboxes.cf virtual_mailbox_base = /home/vmail virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,check_client_access hash:/var/lib/pop-before-smtp/hosts,reject_unauth_destination smtp_use_tls = yes smtpd_use_tls = yes smtpd_tls_auth_only = no smtpd_tls_CAfile = /etc/postfix/cacert.pem smtpd_tls_cert_file = /etc/postfix/smtpd.cert smtpd_tls_key_file = /etc/postfix/smtpd.key smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom virtual_create_maildirsize = yes virtual_mailbox_extended = yes virtual_mailbox_limit_maps = proxy:mysql:/etc/postfix/mysql-virtual_mailbox_limit_maps.cf virtual_mailbox_limit_override = yes virtual_maildir_limit_message = "The user you are trying to reach is over quota." virtual_overquota_bounce = yes debug_peer_list = sender_canonical_maps = debug_peer_level = 1 proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $canonical_maps $sender_canonical_maps $recipient_canonical_maps $relocated_maps $mynetworks $virtual_mailbox_limit_maps $transport_maps alias_maps = hash:/etc/aliases smtpd_relay_restrictions = permit_mynetworks, permit_sasl_authenticated,check_client_access hash:/var/lib/pop-before-smtp/hosts,reject_unauth_destination smtpd_destination_concurrency_limit = 2 smtpd_destination_rate_delay = 1s smtpd_extra_recipient_limit = 10 disable_vrfy_command = yes smtpd_delay_reject = yes smtpd_helo_required = yes smtpd_error_sleep_time = 1s smtpd_soft_error_limit = 10 smtpd_hard_error_limit = 20 This configuration was working before but now everytime i try to send a mail in squirrelmail it reports: Message not sent. Server replied: Requested action aborted: error in processing 451 4.3.0 <[email protected]>: Temporary lookup failure And i can't send mail to it from outsider either. Any ideas? EDIT: Here are some issues MXToolBox reports to my domain, answering hopefully to @Teun Vink: BlackList Mail Server Web Server DNS Error 4 0 2 0 Warnings 0 0 0 3 Passed 0 6 3 12 So the domain is on some blacklist, but that doesn't explain the error at all No mail server issues found (except it's not working) Those two web server errors it's because i don't have HTTPS workin (No SSL Certificate) so the test fails Those 3 DNS warnings we're already there when it was working with the other machine and are related to stuff i can't control: SOA Refresh Value is outside of the recommended range SOA Expire Value out of recommended range SOA NXDOMAIN Value too high I've searched and as far as i can tell only the guys who sold the retail can change those values and they won't. Edit2: I half solved the issue.on the new machine postfix was installed but postfix-mysql waasn't so he couldn't connect to the database (rookie mistake). After fixing that, i can now send mails to the outsider without any issues, however i am still not able to receive mails from utside. The sender doesn't get any message warning about the non-delivery but the message doesn't fall in the inbox and the log shows: Nov 13 15:11:57 m21-traducoes postfix/smtpd[5872]: NOQUEUE: reject: RCPT from re lay4.ptmail.sapo.pt[212.55.154.24]: 451 4.3.5 <relay4.ptmail.sapo.pt[212.55.154. 24]>: Client host rejected: Server configuration error; from=<[email protected]> to=<[email protected]> proto=SMTP helo=<sapo.pt> Nov 13 15:11:57 m21-traducoes postfix/smtpd[5872]: disconnect from relay4.ptmail .sapo.pt[212.55.154.24]

    Read the article

  • can't connect 2 subnets through RRAS 2008 r2

    - by mcdwight6
    I'm working on a project for a networking class. In VMWare Workstation, I have to set up a 2008 r2 server with DHCP reservations for 2 clients on separate subnets and have them ping each other. Here is the output of the route print command: =========================================================================== Interface List 13 ...00 50 56 2a e7 11 ...... Intel(R) PRO/1000 MT Network Connection #3 10 ...00 0c 29 66 88 dd ...... Intel(R) PRO/1000 MT Network Connection 1 ........................... Software Loopback Interface 1 24 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 14 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 16 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 17 ...00 00 00 00 00 00 00 e0 isatap.{5B8FB196-616F-4168-A020-03E63A309CEC} =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.0.2 266 0.0.0.0 0.0.0.0 On-link 223.6.6.2 266 10.0.0.0 255.0.0.0 On-link 10.0.0.2 266 10.0.0.2 255.255.255.255 On-link 10.0.0.2 266 10.255.255.255 255.255.255.255 On-link 10.0.0.2 266 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.6.0.0 255.255.0.0 On-link 10.0.0.2 11 128.6.255.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.0 255.255.255.0 On-link 10.0.0.2 11 223.6.6.0 255.255.255.0 On-link 223.6.6.2 266 223.6.6.2 255.255.255.255 On-link 223.6.6.2 266 223.6.6.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.255 255.255.255.255 On-link 223.6.6.2 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.0.2 266 224.0.0.0 240.0.0.0 On-link 223.6.6.2 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.0.2 266 255.255.255.255 255.255.255.255 On-link 223.6.6.2 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.0.0.2 Default 0.0.0.0 0.0.0.0 128.6.0.2 Default 0.0.0.0 0.0.0.0 223.6.6.2 Default 128.6.0.0 255.255.0.0 10.0.0.2 1 223.6.6.0 255.255.255.0 10.0.0.2 1 =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 1010 2002::/16 On-link 14 266 2002:8006:2::8006:2/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None My problem is that although I have set up both dynamic and persistent static routes in my r2 server, neither of the clients can ping even the NIC outside its own subnet. For example Client A can ping the NIC at 10.0.0.2 and vice-versa, but it gets a general transmit failure when it tries to ping the card at 223.6.6.2, let alone trying to ping the other client. I have completely disabled the firewalls on all machines and anything else I could think of, without success. What am I missing? Edit: Since posting this, I also noticed that the default gateways on my 2 NICs keep getting zeroed out. Does anyone know a fix for this?

    Read the article

  • USB connection is unstable with Nexus S 2.3.4 on AMD 64 running 64-bit Windows 7, but works with 32-bit Windows Vista

    - by Mike
    The USB connection is unstable with Nexus S (Android 2.3.4) on AMD 64 running 64-bit Windows 7, but it works with 32-bit Windows Vista. Problem Description: On the 64-bit Windows 7 machine my Nexus S appears to connect, but then it disconnects moments later. Neither accessing USB storage or loading an Android application package file (APK) using the Android Debug Bridge (ADB) work. On 32-bit Windows Vista using the same USB cable, USB storage works. I haven't tried the ADB on 32-bit Windows Vista. Reproduction steps for USB storage: (I have provided the reproduction steps for USB storage and not ADB, because if one isn't working, then the other isn't working either and the USB storage reproduction steps are shorter to document.) Connect the USB cable to the Nexus S and my Windows 7 machine. Effect: The "USB Mass Storage, USB Connected" dialog appears with the button "Turn on USB storage." Click "Turn on USB Storage" Effect: The "working circle" appears. A dialog briefly appears saying "USB storage in use," then it either returns me to Step 1 (now that I am running 2.3.4) or is replaced with the Nexus S's application homepage (while I was running 2.3.3). I'm not sure if the version matters, but I mention it for completeness. On the 32-bit Windows Vista machine the connection is stable. I am able to navigate through the Nexus S file system create, read, update, and delete files, etc. I haven't tried connecting with the ADB. Troubleshooting summary: Tried and failed: Uninstalling and reinstalling the Android USB drivers including removing the files. Uninstalling my custom software Pulling the Nexus S's battery Restarting the Nexus S Restarting 64-bit Windows 7 Changing USB ports on the 64-bit Windows 7 box Compared the dates and file size on the DLLs in my google-usb_driver\amd64 directory and the windows\System32 directory. They match. The sizes for the google-usb_driver\i386 directory do not match (expected). Turning off Debugging mode on the Nexus S does not resolve the problem. Searching Google. Tried and succeeded: Connecting to another machine (Windows Vista) using the same USB cable and Nexus S phone. Troubleshooting observations: I notice that uninstalling the device drivers and deleting the files, then reinstalling the drivers, then rebooting 64-bit Windows 7 then unplugging the Nexus S, then plugging it back in occasionally helps for a short amount of time (minutes to hours, not days). When it is working, I can both access the Nexus S's drive and load/test applications using the ADB. I have observed some wonky behavior in the Device Manager that I haven't tracked down. Sometimes the black Nexus S image appears in the list of devices. Sometimes the image displays as a computer with a green ISA card. Sometimes it neither appears on the top level of devices nor under “other devices,” but it does appear under "disk drives" as "Android UMS Composite USB Device." System configuration: The Nexus S is running Android OS 2.3.4's "Settings\about phone\System updates" indicates that it is up to date as of May 21st 2011. Both 32-bit Windows Vista and 64-bit Windows 7 are up to date. The Windows Vista system is running on an Intel 32-bit processor. Windows 7 is running on an AMD 64-bit processor. I have done Android development on both systems, but I usually develop on the 64-bit Windows 7 machine.

    Read the article

  • UML assignment question

    - by waitinforatrain
    Hi guys, Sorry, I know this is a very lame question to ask and not of any use to anyone else. I have an assignment in UML due tomorrow and I don't even know the basics (all-nighter ahead!). I'm not looking for a walkthrough, I simply want your opinion on something. The assignment is as follows (you only need to skim over it!): ============= Gourmet Surprise (GS) is a small catering firm with five employees. During a typical weekend, GS caters fifteen events with twenty to fifty people each. The business has grown rapidly over the past year and the owner wants to install a new computer system for managing the ordering and buying process. GS has a set of ten standard menus. When potential customers call, the receptionist describes the menus to them. If the customer decides to book an event (dinner, lunch, picnic, finger food etc.), the receptionist records the customer information (e.g., name, address, phone number, etc.) and the information about the event (e.g., place, date, time, which one of the standard menus, total price) on a contract. The customer is then faxed a copy of the contract and must sign and return it along with a deposit (often a credit card or by check) before the event is officially booked. The remaining money is collected when the catering is delivered. Sometimes, the customer wants something special (e.g., birthday cake). In this case, the receptionist takes the information and gives it to the owner who determines the cost; the receptionist then calls the customer back with the price information. Sometimes the customer accepts the price, other times, the customer requests some changes that have to go back to the owner for a new cost estimate. Each week, the owner looks through the events scheduled for that weekend and orders the supplies (e.g., plates) and food (e.g., bread, chicken) needed to make them. The owner would like to use the system for marketing as well. It should be able to track how customers learned about GS, and identify repeat customers, so that GS can mail special offers to them. The owner also wants to track the events on which GS sent a contract, but the customer never signed the contract and actually booked a GS. Exercise: Create an activity diagram and a use case model (complete with a set of detail use case descriptions) for the above system. Produce an initial domain model (class diagram) based on these descriptions. Elaborate the use cases into sequence diagrams, and include any state diagrams necessary. Finally use the information from these dynamic models to expand the domain model into a full application model. ============= In your opinion, do you think this question is asking me to come up with a package for an online ordering system to replace the system described above, or to create UML diagrams that facilitate the existing telephone-based system?

    Read the article

  • Adding Parsekit To An Xcode Project

    - by Garry
    I am trying to add the Parsekit framework to my OSX Xcode project. I've never added a 3rd party framework before and I can't get it to work right. I dragged the included Xcode project into my 'Groups & Files' pane and chose to Add it to my project. I then dragged Parsekit.framework underneath the Link Binary With Libraries heading. Then I double-clicked my target app and added Parsekit as a Direct Dependency. I also added libicucore.dylib as a Linked Library (as it says to do this on their site). Finally, in the Build settings tab of my target info I set the Header Search Paths to /Users/path/to/include/directory and the Other Linker Flags to -ObjC -all_load. Running this as a debug build work fine with no errors. However, when I build my app to release and then try to run the executable created, the app fails to load with the following error message: MyApp cannot be opened because of a problem. Check with the developer to make sure myApp works with this version of Mac OS X. Here is the dump from the crash reporter: Process: MyApp [11658] Path: /Users/Garry/Programming/Xcode/Mac/MyApp/build/Release/MyApp.app/Contents/MacOS/MyApp Identifier: com.yourcompany.MyApp Version: ??? (???) Code Type: X86-64 (Native) Parent Process: launchd [135] Date/Time: 2010-05-24 17:08:08.475 +0100 OS Version: Mac OS X 10.6.3 (10D573) Report Version: 6Interval Since Last Report: 133300 sec Crashes Since Last Report: 3 Per-App Crashes Since Last Report: 3 Anonymous UUID: DF0265E4-B5A0-45E1-8B71-D52A27CFDDCA Exception Type: EXC_BREAKPOINT (SIGTRAP) Exception Codes: 0x0000000000000002, 0x0000000000000000 Crashed Thread: 0 Dyld Error Message: Library not loaded: @executable_path/../Frameworks/ParseKit.framework/Versions/A/ParseKit Referenced from: /Users/Garry/Programming/Xcode/Mac/MyApp/build/Release/MyApp.app/Contents/MacOS/MyApp Reason: image not found Model: MacBookPro5,5, BootROM MBP55.00AC.B03, 2 processors, Intel Core 2 Duo, 2.53 GHz, 4 GB, SMC 1.47f2 Graphics: NVIDIA GeForce 9400M, NVIDIA GeForce 9400M, PCI, 256 MB Memory Module: global_name AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.10.91.27) Bluetooth: Version 2.3.1f4, 2 service, 2 devices, 1 incoming serial ports Network Service: AirPort, AirPort, en1 Network Service: Ethernet Adaptor (en6), Ethernet, en6 Serial ATA Device: Hitachi HTS545025B9SA02, 232.89 GB Serial ATA Device: HL-DT-ST DVDRW GS23N USB Device: Built-in iSight, 0x05ac (Apple Inc.), 0x8507, 0x24400000 USB Device: Internal Memory Card Reader, 0x05ac (Apple Inc.), 0x8403, 0x26500000 USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0x04500000 USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0237, 0x04600000 USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x06100000 USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8213, 0x06110000 After building the app, in addition to the executable file, Xcode is also creating a file called MyApp.app.dSYM. Any idea what that is?? I am developing with Xcode 3.2.2 on an Intel MBP running 10.6.3. Many thanks for any help offered.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 262 263 264 265 266 267 268 269 270 271 272 273  | Next Page >