Search Results

Search found 7976 results on 320 pages for 'sl dev'.

Page 266/320 | < Previous Page | 262 263 264 265 266 267 268 269 270 271 272 273  | Next Page >

  • Force local IP traffic to an external interface

    - by calandoa
    I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to forward all the traffic sent to one of these local addresses through the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 should be not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. May be I could then do NAT forwarding of all traffic directed to fake 192.168.1.2 on eth1, rerouted to 192.168.1.1 internally? I am actually struggling with iptables, but it is too tough for me. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

    Read the article

  • Recovering a damaged microSDHC

    - by djechelon
    I just bought from eBay a Kingston 32GB microSDHC that was advertised as defective. The seller said that there could be formatting problems or with transfer of large files. Unfortunately, when I got it, it was a total mess. My Nikon camera doesn't read it at all (OK, maybe it doesn't support 32GB) My Linux laptop doesn't mount it: can't read superblock The same laptop refuses to mkfs.msdos because it failed whilst writing reserved sector The same laptop, under Windows, doesn't read nor format the card HTC HD2 mounts the MMC, allows me to write via USB, but is unable to open the just written files OK, folks, now you would say I would have to go through Paypal complaint... that's not that easy. I consciously bought a half-price card that was known to show some defects, and Paypal complaints take time. Obviously, I can't accept somebody sold me a completely use-less computer decoration. So I'll keep it as last option. My question is Do you know a way, under either Linux or Windows, to thoroughly scan, test and possibly repair memory cards, even if I have to lose some percentage of space because of bad sectors? If I can keep at least half of the card intact it would certainly be fine. I used to do broken sector marking with hard disks in the past. I almost forgot: MONSTR:/home/djechelon # fsck /dev/mmcblk0p1 fsck from util-linux-ng 2.17.2 dosfsck 3.0.9, 31 Jan 2010, FAT32, LFN Read 512 bytes at 0:Input/output error

    Read the article

  • Linux: How do I remove bootchart from the boot process?

    - by java.is.for.desktop
    Hello, everyone! I have OpenSUSE 11.2. I removed bootchart and forgot to run mkinitrd. Now, right at the start of the boot process, I get boot/93-bootchart.sh: line 17: 462 Terminated stopinitrd 5 I Can't find any 93-bootchart.sh anywhere. Failsafe boot mode doesn't help. Earlier I got an error message about non existing /sbin/bootchartd, but I just copied /bin/cat to /sbin/bootchartd using a GParted boot disk. I tried to use chroot with an OpenSUSE boot disk, but mkinitrd can't find the root device, which is there actually (/dev/sda5). How can I make my system boot again? EDIT Ok, now I managed to re-install the bootchart rpm, using OpenSUSE boot disk and chmod. The system starts again. But that annoying bootchart is still there. I will not try again to remove it. First I will try to figure out, how to disable it during the boot process. Hopefully with your help ;)

    Read the article

  • Squid SSL transparent proxy - SSL_connect:error in SSLv2/v3 read server hello A

    - by larryzhao
    I am trying to setup a SSL proxy for one of my internal servers to visit https://www.googleapis.com using Squid, to make my Rails application on that server to reach googleapis.com via the proxy. I am new to this, so my approach is to setup a SSL transparent proxy with Squid. I build Squid 3.3 on Ubuntu 12.04, generated a pair of ssl key and crt, and configure squid like this: http_port 443 transparent cert=/home/larry/ssl/server.csr key=/home/larry/ssl/server.key And leaves almost all other configurations default. The authorization of the dir that holds key/crt is drwxrwxr-x 2 proxy proxy 4096 Oct 17 15:45 ssl Back on my dev laptop, I put <proxy-server-ip> www.googleapis.com in my /etc/hosts to make the call goes to my proxy server. But when I try it in my rails application, I got: SSL_connect returned=1 errno=0 state=SSLv2/v3 read server hello A: unknown protocol And I also tried with openssl in cli: openssl s_client -state -nbio -connect www.googleapis.com:443 2>&1 | grep "^SSL" SSL_connect:before/connect initialization SSL_connect:SSLv2/v3 write client hello A SSL_connect:error in SSLv2/v3 read server hello A SSL_connect:error in SSLv2/v3 read server hello A Where did I do wrong?

    Read the article

  • Setup git repository on gentoo server using gitosis & ssh

    - by ikso
    I installed git and gitosis as described here in this guide Here are the steps I took: Server: Gentoo Client: MAC OS X 1) git install emerge dev-util/git 2) gitosis install cd ~/src git clone git://eagain.net/gitosis.git cd gitosis python setup.py install 3) added git user adduser --system --shell /bin/sh --comment 'git version control' --no-user-group --home-dir /home/git git In /etc/shadow now: git:!:14665:::::: 4) On local computer (Mac OS X) (local login is ipx, server login is expert) ssh-keygen -t dsa got 2 files: ~/.ssh/id_dsa.pub ~/.ssh/id_dsa 5) Copied id_dsa.pub onto server ~/.ssh/id_dsa.pub Added content from file ~/.ssh/id_dsa.pub into file ~/.ssh/authorized_keys cp ~/.ssh/id_dsa.pub /tmp/id_dsa.pub sudo -H -u git gitosis-init < /tmp/id_rsa.pub sudo chmod 755 /home/git/repositories/gitosis-admin.git/hooks/post-update 6) Added 2 params to /etc/ssh/sshd_config RSAAuthentication yes PubkeyAuthentication yes Full sshd_config: Protocol 2 RSAAuthentication yes PubkeyAuthentication yes PasswordAuthentication no UsePAM yes PrintMotd no PrintLastLog no Subsystem sftp /usr/lib64/misc/sftp-server 7) Local settings in file ~/.ssh/config: Host myserver.com.ua User expert Port 22 IdentityFile ~/.ssh/id_dsa 8) Tested: ssh [email protected] Done! 9) Next step. There I have problem git clone [email protected]:gitosis-admin.git cd gitosis-admin SSH asked password for user git. Why ssh should allow me to login as user git? The git user doesn't have a password. The ssh key I created is for the user expert. How this should work? Do I have to add some params to sshd_config?

    Read the article

  • Linux DHCPD Mac-Address based Groups

    - by GruffTech
    Our Current DHCPD.conf looks like the following. subnet 10.0.32.0 netmask 255.255.255.0 { range 10.0.32.100 10.0.32.254; option subnet-mask 255.255.255.0; option broadcast-address 10.0.32.255; option domain-name-servers 208.67.222.222,208.67.220.220; option routers 10.0.32.5; host Dev-ABaird-W { hardware ethernet 00:1D:09:3E:49:13; fixed-address 10.0.32.94; } ... more static hosts .... } About as basic as it gets. The old router is 10.0.32.1, our company wanted to implement a squid proxy to better monitor web traffic while at work, and if necessary block large time-wasters, IE Facebook.com. However, we've quickly realized that this change has played a mean prank on our Polycom SIP Phones. Occasionally our phones will not ring, the end recipient hears ringing (this is artificially created by our PBX) however the handset never rings. The ONLY thing that has changed in our network is the option routers line. So, Since all Polycom MAC addresses begin with 00:04:F2 would it be possible in DHCP to say any 00:04:F2:::* MAC addresses get option routers 10.0.32.1, and anything else must talk with our Gateway?

    Read the article

  • Add IPv6 support to DirectAdmin server

    - by George Boot
    I just set up an new DirectAdmin, and I want to prepare it for IPv6 use. My ISP have gave me an range of IPv6 addresses that I can use. Lets say that address is 2a01:7c8:**:1f::. My neworkadapter user DHCP to resolves its IP-addresses. When i type ifoncig eth0 I get the following result: eth0 Link encap:Ethernet HWaddr 52:**:**:**:ce:f3 inet addr:37.**.**.44 Bcast:37.**.**.255 Mask:255.255.255.0 inet6 addr: 2a01:7c8:****:1f::/64 Scope:Global inet6 addr: fe80::5054:ff:fe87:cef3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38941 errors:0 dropped:0 overruns:0 frame:0 TX packets:29439 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3779534 (3.6 MiB) TX bytes:5089379 (4.8 MiB) As you can see, I have an IPv6 address set, but I can't ping6 an IPv6 host. I get the error: connect: Network is unreachable. I decided that I needed an gateway, so I tryed to add one: ip -6 route add default via 2a01:7c8:****::1 dev eth0 (2a01:7c8:**::1 is the gateway of my ISP). But it trows an error: RTNETLINK answers: No route to host. Does somebody know what to do, and how to solve this issue? Thanks a lot!

    Read the article

  • MacBook Pro (OSX Lion) - shutdown automatically before reaching login screen

    - by mkk
    When I try to lunch my MacBook Pro I can see a progress bar on loading screen. It goes to 1/15 or something like this and then it shut downs - I cannot reach even login screen. It happened to me 2 months ago, I have 'fixed' this by formatting my hard drive and installing OSX (Lion) again. This time I think that situation is a little bit different - I am able to enter single-user mode by pressing cmd + s. I then type /sbin/fsck -yf, I get the error: ** Checking Journaled HFS Plus volume. The volume name is Macintosh HD ** Checking extents overflow file. ** Checking catalog file. Invalid node structure (4, 24704) ** The volume Macintosh HD could not be verified completely. /dev/rdisk0s2 (hfs) EXITED WITH SIGNAL 8 but when I type exit, I can the login screen and I can log in. I tried a lot of things, booting from recovery partition and choosing disk utility to repair the disc, but I get error that it cannot be repaired. I have googled for hours and the only real solution I have found was to buy Disc warrior that might fix the issue. Any other suggestions? Secondary question is what causes this issue? I thought the reason are bad sectors, but Smart Utility haven't found any. I found suggestion that RAM could cause this kind of issue as well, so I downloaded rember and made memory test - all tests passed. Right now I have used my solution of entering single-mode user and then typing exit, however I am not sure how long it will 'work'. Of course I have back-uped what I considered important. Thanks for the help in advance! UPDATE: I guess Smart Utility was not very useful, I mnaged to get input/output error, which I believe is equivalent to bad sector.

    Read the article

  • Small Business HP Virtualisation and iSCSI SAN Options

    - by Robin Day
    We are a small business that hosts our core product on a number of HP servers. Our core production setup is 1x HP DL380, high powered for a SQL Server Database 1x HP DL360, mid powered for our core application server 6x HP DL320, low powered for our front ends We run our training / testing / support systems on a similar setup, the servers are just older and less powerful. Unfortunately this is now causing us issues as the system has grown beyond the capabilities of these older servers. Upgrading these servers would be expensive and we believe that virtualisation is probably the way to go for the future. Locally we run a number of test / dev environments on ESXi using Direct Storoage on a couple of high powered DL360's and these are performing fairly well. We're thinking that instead of replacing all of our test servers that we can implement an iSCSI SAN and one or two high powered hosts. Hopefully looking that when it comes to replace our live servers as well that we can just expand the virual environment to cope. So my question is... Can anyone offer any advice on some suitable options? We have generally always been extremely happy with HP servers, all of our kit is currently HP, therefore our preference would be to stick with HP, however, I'm always happy to hear about other options. I'm hoping that initially a budget of around 15-25k (GBP) would be suitable, this could potentially be increased if I had confidence that the system would pave the way for a cost effective upgrade of our live systems in the future as well. I am new to SAN's and my only real experience is playing with OpenFiler on some old desktops. I think iSCSI should be suitable, but I've not done any research into how SQL server may perform. I've had a browser through HP's sites and see plenty of information about EVA, MSA, LeftHand, etc. However, from looking at all that, I don't see which options would be best and more importantly I don't know exactly what I would need to buy. Any help, links, opinions would be much appreciated. Thanks

    Read the article

  • Debootstrap Ubuntu over NFS leads to mknod I/O error

    - by Aaron B. Russell
    Hi everyone, I'm trying to prepare an Ubuntu environment for a diskless machine that will PXE boot and mount an NFS share as it's root. I've currently got another Ubuntu machine mounting the NFS share and I'm trying to debootstrap into it, but it has trouble creating devices over NFS: root@kimiko:~# mount | grep Seiuchi 192.168.0.203:/mnt/user/Seiuchi on /mnt type nfs (rw,addr=192.168.0.203) root@kimiko:~# debootstrap --arch i386 maverick /mnt http://gb.archive.ubuntu.com/ubuntu/ mknod: `/mnt/test-dev-null': Input/output error E: Cannot install into target '/mnt' mounted with noexec or nodev My NFS rule on the unRAID server is 192.168.0.201/32(rw,no_root_squash,sync). I don't have the noexec or nodev options set. I've not got much experience with NFS, so I'm probably missing something basic in the way I'm sharing this, but my attempts at Googling for an answer isn't really turning anything useful up. Does anyone have suggestions on what I might have missed or maybe relevant docs? Edit: Creating normal files (and directories) works just fine, I just can't create devices... root@kimiko:/mnt# mkdir foo root@kimiko:/mnt# cd foo root@kimiko:/mnt/foo# touch bar root@kimiko:/mnt/foo# mknod quux c 4 64 mknod: `quux': Input/output error root@kimiko:/mnt/foo# ls bar

    Read the article

  • Scanning website for vulnerablities

    - by Kristen
    I have found that the local school's website installed a Perl Calendar - this was years ago, it has not been used for ages, but Google has it indexed (which is how I found it) and it full of Viagra links and the like ... program was by Matt Kruse, here is details of the exploit: http://www.securiteam.com/exploits/5IP040A1QI.html I've got the school to remove that, but I think they also have MySQL installed and I'm aware that out-of-the-box there have been some exploits of Admin Tools / Login in old versions. For all I know they also have PHPBB and the like installed ... The school is just using some cheap, shared hosting; the HTTP response header I get is: Apache/1.3.29 (Unix) (Red-Hat/Linux) Chili!Soft-ASP/3.6.2 mod_ssl/2.8.14 OpenSSL/0.9.6b PHP/4.4.9 FrontPage/5.0.2.2510 I'm looking for some means of checking if they have other junk installed (quite possibly from way back, and now unused) that might put the site at risk. I'm more interested in something that can scan for things like the MySQL Admin exploit rather than open ports etc. My guess is that they have little control over the hosting space that they have - but I'm a Windows DEV, so this *nix stuff is all Greek to me. I found http://www.beyondsecurity.com/ which looks like it might do what I want (within their evaluation :) ) but I have a worry about how to find out if they are well known / honest - otherwise I will be tipping them a wink with a Domain Name that may be at risk! Many thanks.

    Read the article

  • Xen 4.1.2 unable to boot

    - by Devator
    I have installed Xen 3.1.2 perfectly, and it's running fine. However since that version is way outdated I just updated it to 4.1.2 by adding the gitco repository and then yum update. It installed fine, modified my grub.conf to reflect the changes but then on a reboot, it simply doesn't come back online (I can't see what's going on, as it's a rented dedicated server). What are my options? Booting into rescue mode and using the older kernel works fine, it will come back up. But once I use the xen.gz-4.1.2kernel, it won't come back up anymore and I need to use the rescue image.. My /boot/grub/grub.confis as follows: title CentOS (2.6.18-308.1.1.el5xen) root (hd0,1) #kernel /xen.gz-2.6.18-308.1.1.el5 dom0_mem=1024M kernel /xen.gz-4.1.2 module /vmlinuz-2.6.18-308.1.1.el5xen ro root=/dev/md1 module /initrd-2.6.18-308.1.1.el5xen.img When I uncomment the 3.1.2 kernel, it works fine, but booting with the 4.1.2 kernel fails and I have no idea what's going on. Hence my question: what are my options?

    Read the article

  • Forcing a particular SSL protocol for an nginx proxying server

    - by vitch
    I am developing an application against a remote https web service. While developing I need to proxy requests from my local development server (running nginx on ubuntu) to the remote https web server. Here is the relevant nginx config: server { server_name project.dev; listen 443; ssl on; ssl_certificate /etc/nginx/ssl/server.crt; ssl_certificate_key /etc/nginx/ssl/server.key; location / { proxy_pass https://remote.server.com; proxy_set_header Host remote.server.com; proxy_redirect off; } } The problem is that the remote HTTPS server can only accept connections over SSLv3 as can be seen from the following openssl calls. Not working: $ openssl s_client -connect remote.server.com:443 CONNECTED(00000003) 139849073899168:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:s23_lib.c:177: --- no peer certificate available --- No client certificate CA names sent --- SSL handshake has read 0 bytes and written 226 bytes --- New, (NONE), Cipher is (NONE) Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE --- Working: $ openssl s_client -connect remote.server.com:443 -ssl3 CONNECTED(00000003) <snip> --- SSL handshake has read 1562 bytes and written 359 bytes --- New, TLSv1/SSLv3, Cipher is RC4-SHA Server public key is 1024 bit Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE SSL-Session: Protocol : SSLv3 Cipher : RC4-SHA <snip> With the current setup my nginx proxy gives a 502 Bad Gateway when I connect to it in a browser. Enabling debug in the error log I can see the message: [info] 1451#0: *16 peer closed connection in SSL handshake while SSL handshaking to upstream. I tried adding ssl_protocols SSLv3; to the nginx configuration but that didn't help. Does anyone know how I can set this up to work correctly?

    Read the article

  • Suspected brute force attack

    - by HarveySaayman
    Recently I acquired a dedicated server from a local ISP to play around with. As the tags suggest, its a windows server 2008 R2 machine. I've only had it for a few days, and no real traffic is going to it yet. I haven't even deployed a "real" website to it yet. Just a silly page so that I could check IIS, my host headers, DNS records, etc are all configured correctly. While playing around, I noticed a ton of Audit Failure entries in the event viewers security logs. It seems something is trying to access the administrator account, and failing. It smells like a brute force attack to me. My ISP gave me the account details of the administrator account and I used those to RDP into the box, which I've heard is not the securest of situations. I created myself another account and added myself to the administrator group, so im using that account to gain acceess to the machine now. In response to all of this i used http://strongpasswordgenerator.com/ to generate me some 20 character length strong passwords and changed all of my account passwords, even the SQL sa user. I also enabled the auto ban feature of FileZillaServer (my FTP server) My questions: 1) how can i detect this kind of thing better? 2) how can i protect my server from unauthorized access better? PS: I'm a software dev, not a sysadmin so please mind my server security idiot-ness-ness

    Read the article

  • High disk I/O - jbd2/sda2-8 process

    - by Evan Hamlet
    I have run a file server on a CentOS 5.8 final server. My only concern at the moment is what appears to be intermittent but continuous high disk I/O activity causing a general slowdown because of jbd2/sda2-8 process. jbd2/sda2-8 is making use of /dev/sda2, which is the 2nd partition of the first harddrive (IE: root partition). More info: using "iotop" the culprit appears to be "jbd2/sda1-8" making writes every second, which appears to be a kernel process associated with journaling on the ext4 filesystem, if my googling around is correct. I see "jbd2/sda2-8" appearing here every now and then, but certainly not every 3 seconds.. when idle, it appears about 1 or 2 times per minute. When I'm using the system, it appears more frequently. ATOP results: http://grabilla.com/02b14-8022db2e-4eb9-4f10-8e10-d65c49ad7530.png IOTOP results: http://grabilla.com/02b14-cf74b25d-4063-4447-9210-7d1b9b70e25b.png HTOP results: grabilla. com/02b14-ad8cad0e-89b0-46d3-849d-4fd515c1e690.png jbd2/sda2-8 is the processes I see with iotop making writes on disk even though it's not in use at all. Does someone has any idea how could I solve the high disk usage caused jbd2/sda2-8 process?

    Read the article

  • Compiled git from source, cannot access subversion repositories using git-svn

    - by haydenmuhl
    I'm setting up a CentOS dev box, and need git. At first I tried to install git using yum, but I could not connect to a yum repository that had git. Next I downloaded the git source (version 1.7.1) and compiled it. When I run the following command git svn clone svn+ssh://... I get the following error. Initialized empty Git repository in /root/main_ec/.git/ Can't locate SVN/Core.pm in @INC (@INC contains: /usr/local/lib/perl5/site_perl/5.8.8/i386-linux-thread-multi /usr/local/lib/perl5/site_perl/5.8.8 /usr/lib/perl5/site_perl/5.8.8/i386-linux-thread-multi /usr/lib/perl5/site_perl/5.8.8 /usr/lib/perl5/site_perl /usr/lib/perl5/vendor_perl/5.8.8/i386-linux-thread-multi /usr/lib/perl5/vendor_perl/5.8.8 /usr/lib/perl5/vendor_perl /usr/lib/perl5/5.8.8/i386-linux-thread-multi /usr/lib/perl5/5.8.8 .) at /usr/local/libexec/git-core/git-svn line 41. It looks like git-svn uses perl in some manner, but I don't know packages I'm missing. Can anyone help?

    Read the article

  • Problems installing MySQL-python via yum / missing dependency / incompatibility problem?

    - by bs0
    I have come up against problems installing MySQL-python via yum. Our server is running Centos 5.5 and MySQL Version 5.1.45, Python-dev is installed. Yum complains about the missing dependency libmysqlclient_r.so.15: Missing Dependency: libmysqlclient_r.so.15()(64bit) is needed by package MySQL-python-1.2.1-1.x86_64 (base) The server is up to date and the packages mysql mysql-devel python-devel are installed. The missing dependency is nowhere on the system: locate libmysqlclient /usr/lib64/libmysqlclient.so /usr/lib64/libmysqlclient.so.15 /usr/lib64/libmysqlclient.so.16 /usr/lib64/libmysqlclient.so.16.0.0 /usr/lib64/libmysqlclient_r.so /usr/lib64/libmysqlclient_r.so.16 /usr/lib64/libmysqlclient_r.so.16.0.0 /usr/lib64/mysql/libmysqlclient.a /usr/lib64/mysql/libmysqlclient.la /usr/lib64/mysql/libmysqlclient.so /usr/lib64/mysql/libmysqlclient_r.a /usr/lib64/mysql/libmysqlclient_r.la /usr/lib64/mysql/libmysqlclient_r.so /usr/local/cpanel/lib64/libmysqlclient.so.14 rpm -qa | grep -i mysql MySQL-devel-5.1.45-0.glibc23 MySQL-bench-5.0.89-0.glibc23 MySQL-shared-5.1.45-0.glibc23 MySQL-server-5.1.45-0.glibc23 MySQL-test-5.1.45-0.glibc23 MySQL-client-5.1.45-0.glibc23 The Python version is python-2.4.3-27.el5.x86_64: Python 2.4.3 (#1, Sep 3 2009, 15:37:37) [GCC 4.1.2 20080704 (Red Hat 4.1.2-46)] on linux2 Any suggestions would be greatly appreciated.

    Read the article

  • Is StoreJet Transcend (0x2329) an Advanced Format drive?

    - by Graham Perrin
    I use a 640 GB StoreJet Transcend (0x2329) with ZEVO Community Edition 1.1.1 on OS X 10.8.2. Question Is this drive Advanced Format? Background I submitted a request for technical support to Transcend but the first response was gibberish so I don't expect a reasonable follow-up. Models at http://www.transcend-info.com/Products/CatList.asp?LangNo=0&ModNo=293 are similar but different sizes (not 640 GB). Mine is probably 25M2 (TS640GSJ25M2): Unless I'm missing something, nothing currently in the Transcend support area tells me whether the drive is Advanced Format. From System Information in OS X 10.8.2: StoreJet Transcend: Capacity: 640.14 GB (640,135,028,736 bytes) Removable Media: Yes Detachable Drive: Yes BSD Name: disk3 Product ID: 0x2329 Vendor ID: 0x152d (JMicron Technology Corp.) Version: 0.00 Serial Number: 322549FBA004 Speed: Up to 480 Mb/sec Manufacturer: JMicron History for the ZFS pool shows creation in March 2012 –  macbookpro08-centrim:~ gjp22$ zpool history zhandy | grep create 2012-03-14.17:29:37 zpool create -f -O compression=off -O copies=1 -O casesensitivity=insensitive -O snapdir=visible zhandy /dev/dsk/GPTE_1928482A-7FE4-482D-B692-3EC6B03159BA 2012-06-22.15:51:16 zfs create zhandy/Pocket Time Machine At that time I almost certainly used ZEVO Setup Assistant to create the pool. macbookpro08-centrim:~ gjp22$ zpool get ashift zhandy NAME PROPERTY VALUE SOURCE zhandy ashift 0 default If I discover that the drive is Advanced Format, a different ashift value will be appropriate.

    Read the article

  • PHP enable sqlite phpinfo states --without-sqlite

    - by Jahmic
    I've seen similar questions but none that address my situation adequately. I'm running Apache and PHP 5.3.6 on a amazon cloud server. phpinfo keeps stating that sqlite is disabled. At least that what it seems from the configure line: './configure' ... '--without-sqlite' In other parts of phpinfo() output: PDO PDO drivers mysql, sqlite PDO Driver for SQLite 3.x enabled SQLite Library 3.6.20 sqlite3 SQLite3 support enabled SQLite3 module version 0.7-dev SQLite Library 3.6.20 Directive Local Value Master Value sqlite3.extension_dir no value no value and at least one the following PHP commands fail: if (!extension_loaded('SQLite') OR !function_exists('sqlite_open')) Yum install states that both sqlite and pdo-lite are already installed. I've tried to enable sqlite by editing my local php.ini by adding: ; Enable sqlite3 extension module extension=sqlite3.so I've checked the main php.ini (/etc/php.ini) and there is nothing specific about disabling it. In fact, there is a sub-conig file loaded in php.d that also specifies this extension as well as another for the pdo-sqlite I'm running of things to look for or try. Any suggestions. How do I find where the PHP configure is stated? Thanks

    Read the article

  • Test server on a local network with XAMPP

    - by hopscotch1978
    Hi, I'm not very proficient with networks and could use some help. I've got a Win 7 desktop with XAMPP which acts as my local dev machine. I've configured a virtual host on the desktop which I'm able to access fine. If I'm understanding things correctly, the virtual host uses port 80 (<VirtualHost 127.0.0.1:80>). I've just tried to configure a separate Win XP laptop on the local wireless network to connect to the main desktop for testing purposes. I've added the IP address and virtual host name to my Hosts file on the laptop. My virtual host is imaginatively named "virtualhost1". When I type this into my laptop browser, it connects correctly to the main desktop and I get the XAMPP welcome screen. But I can't seem to get to the actual site, just the XAMPP welcome screen. It kind of jumps the browser to http://virtualhost1/xampp/. I think it's a port issue of some sort but I have no idea how to resolve it. I would get the same XAMPP welcome screen on my desktop if I omitted ":80" from the virtual host declaration. On my main desktop, typing "virtualhost1" to the browser address bar gives me the site correctly, not the XAMPP welcome screen. Help would be appreciated. Thank you.

    Read the article

  • How do I boot [embedded] linux from sd card?

    - by Brandon Yates
    I am hacking together a quick embedded linux system on a DM816x evm board. Previously I have been using TFTP and NFS to load my kernel and root filesystem to the board. I am now trying to switch over to loading everything from an SD card. I have my card partitioned such that uBoot and my kernel image are in one partition, and my rootFS in another partition. At power-on, Uboot starts correctly and successfully launches the kernel. However, the kernel is unable to mount the root file system. It appears that it doesn't recognize any SD (mmc) cards. It gives this error message. VFS: Cannot open root device "mmcblk0p2" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 256 mtdblock0 (driver?) 1f01 8 mtdblock1 (driver?) 1f02 2560 mtdblock2 (driver?) 1f03 1272 mtdblock3 (driver?) 1f04 2432 mtdblock4 (driver?) 1f05 128 mtdblock5 (driver?) 1f06 4352 mtdblock6 (driver?) 1f07 204928 mtdblock7 (driver?) 1f08 50304 mtdblock8 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) I feel like I'm missing something fundamental here. Why does it not recognize the root device I am trying to load from? Here is my uBoot boot script that is running: setenv bootargs console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw mem=124M earlyprink vram=50M ti816xfb.vram=0:16M,1:16M,2:6M ip=off noinitrd;mmc init;fatload mmc 1 0x80009000 uImage;bootm 0x80009000

    Read the article

  • Enabling CURL on Ubuntu 11.10

    - by Afsheen Khosravian
    I have installed curl: sudo apt-get install curl libcurl3 libcurl3-dev php5-curl and I have updated my php.ini file to include(I also tried .so): extension=php_curl.dll To test if curl is working I created a file called testCurl.php which contains the following: <?php echo ‘<pre>’; var_dump(curl_version()); echo ‘</pre>’; ?> When I navigate to localhost/testCurl.php I get an error: HTTP Error 500 Heres a snippet from the error log: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626+lfs/php_curl.dll' - /usr/lib/php5/20090626+lfs/php_curl.dll: cannot op$ PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626+lfs/sqlite.so' - /usr/lib/php5/20090626+lfs/sqlite.so: cannot open sha$ [Sun Dec 25 12:10:17 2011] [notice] Apache/2.2.20 (Ubuntu) PHP/5.3.6-13ubuntu3.3 with Suhosin-Patch configured -- resuming normal operations [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/ [Sun Dec 25 12:13:46 2011] [error] [client 127.0.0.1] File does not exist: /var/www/css, referer: http://localhost/` Can anyone help me to get curl working? The problem was with the original test code. I used a new test file containing this and curl is now working: <?php ## Test if cURL is working ## ## SCRIPT BY WWW.WEBUNE.COM (please do not remove)## echo '<pre>'; var_dump(curl_version()); echo '</pre>'; ?>

    Read the article

  • How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

    - by Todd V. Rovito
    I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

    Read the article

  • sharing a folder between linux and windows over the internet

    - by valya
    Hello Currently my job is to make websites with Django. I use many things like virtualenv, PIL, etc. The problem is, I can't stand Linux on my desktop. I like it on servers, It's greate to use it over the SSH. But for desktop? No way. But for the development Linux is quite essential. Of course almost everything is ported to Windows, but it's not as simple to use as in Linux. For example, Windows shell is awful in comparison with Linux. So I've tried Cygwin, but it's too damn slow. Every time django dev server reloads, it tooks almost 20-30 seconds. In comparison, then using "native" python on Windows or Linux, it reloads instantly. Even worse, Cygwin makes all my system very slow. I've been thinking about it and have thought up a way to go. I can share a folder with my application with some Linux box. The devserver and everything will run on that box, while I'll be happy editing files and running the browser on my Windows 7. SSH shell is much quickier and handy than Cygwin. Currently there are no Linux boxes in my home network (except for my android phone :) but I have several VDS boxes with Debian. So, how do I share a Windows folder with VDS box? I can't rely on my desktop IP but I can rely on the VDS's one. I need sharing to be as quick as possible (well, 2-3 seconds ping is OK) and "native" for both systems, so I could use a folder like a normal folder in both Windows and Linux.

    Read the article

  • JSP Content Issue in Tomcat

    - by gautam vegeta
    There is one application where I work where there are still manual builds used i.e manually moving the servlet classes and jsp files from Dev to QA and finally to Prod. This is the method used in this application which cant be changed for some wierd reasons.BTW this is not the problem. We did a manual build where we transferred jsp files from QA to PROD recently. And we noticed that the jsp file content does not correspond to the updated jsp's but have the same content to the jsp file which was present in the server prior to the deployment. We did not re-start tomcat since jsp files upon updation automatically changes its contents. This problem persisted even after 6 hours of deployment If we consider the time standards which are different which may cause some delay. So to fix this we had to individually go into every jsp file and just type something save it and delete this change and save it.Then it worked perfectly. But finally the jsp file content before and after was never changed we just did this to change the modification date. If we think in terms of timestamp problem how can this be possible coz the old jsp files which were present in the server prior to deployment was atlest one month old and the ones getting deployed were defenitely newer than that. Why did this happen? This did not happen when we did same type of deployments earlier. How can we prevent this from happening in the future.

    Read the article

< Previous Page | 262 263 264 265 266 267 268 269 270 271 272 273  | Next Page >