Search Results

Search found 10759 results on 431 pages for 'auto detect'.

Page 27/431 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

• 2-Bay External HDD Enclosure in JBOD mode fails to detect both drives (Linux & Windows)

  - by mgc8888

  I recently purchased a couple of USB 3.0 External HDD Enclosures to use for storage and backup; the idea was to have one act as backup to the other, with 4 x 3TB drives in total. However, the second drive in each is not accessible in either Linux nor Windows, and I could not determine the reason. 1. Situation The two enclosures are slightly different (couldn't find them in stock at the same time) yet from many little details appear to be the same Chinese base design with a tweaked outer shell. The models are: Sharkoon 2-Bay RAID Box Fantec MR-35DU3 The drives are Seagate 3TB Barracuda ST33000651AS, firmware CC44, all identical. From reading manuals and online sources, I determined that JBOD would be the optimal setup for my needs -- addressing the two drives separately in each enclosure would be important, making it easy to swap drives and mix&match them if needed; all the other modes implied the controller doing a combination of the drives. The software used was Debian GNU/Linux - testing/wheezy - kernel 2.6.39-2 and Windows 7 Ultimate. 2. Description of the problem Now, here comes the problem: every time I connect either of the enclosures to a PC using the supplied cable (tried a different one as well), only the HDD in the top bay is readable, the one below is detected yet errors out in various ways. According to the manuals, it should not happen: in JBOD, the system should be able to "see" two separate drives upon connection. This happens with both enclosures and any combination of HDDs (i.e. if I swap them, the same thing happens), so the HDDs are good and I think so are the enclosures (two different companies making similar products that failed in an identical fashion would be very unlikely). The top HDD can be used fine every time, I actually tried a speed test from Linux and got about 150MiB/s reads, so all is working as it should; the one below refuses to work every time. So the failure is consistent. To make sure this was not some obscure Linux bug, I tried the same under Windows 7, and the system also only created one drive letter for a drive of 3TB size (so it was only seeing one instead of both). Placing an older, known good, 2TB drive in the top bay made that the one recognised, so we have the same issue under Windows as well. Log entries under Linux (tested here with a 3TB and a 2TB drive so I could differentiate them; either one works in the top enclosure, in the test setup the 3TB one is on top). You can see them being detected, the top one is ok, but for the bottom one only errors: Jul 19 23:28:15 media kernel: [260150.582436] usb 6-1: New USB device found, idVendor=1ca1, idProduct=18ae Jul 19 23:28:15 media kernel: [260150.582440] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jul 19 23:28:15 media kernel: [260150.582442] usb 6-1: Product: Usb Sata Bridge Jul 19 23:28:15 media kernel: [260150.582444] usb 6-1: Manufacturer: SYMWAVE Jul 19 23:28:15 media kernel: [260150.582446] usb 6-1: SerialNumber: 39584B304C4E3441 Jul 19 23:28:15 media kernel: [260150.870412] scsi11 : usb-storage 6-1:1.0 Jul 19 23:28:16 media kernel: [260151.882087] scsi 11:0:0:0: Direct-Access SYMWAVE ST33000651AS CC44 PQ: 0 ANSI: 4 Jul 19 23:28:16 media kernel: [260151.882242] scsi 11:0:0:1: Direct-Access SYMWAVE ST32000641AS CC12 PQ: 0 ANSI: 4 Jul 19 23:28:16 media kernel: [260151.882677] sd 11:0:0:0: Attached scsi generic sg2 type 0 Jul 19 23:28:16 media kernel: [260151.882774] sd 11:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16). Jul 19 23:28:16 media kernel: [260151.882857] sd 11:0:0:1: Attached scsi generic sg3 type 0 Jul 19 23:28:16 media kernel: [260151.882893] sd 11:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Jul 19 23:28:16 media kernel: [260151.883085] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.883582] sd 11:0:0:0: [sdb] Write Protect is off Jul 19 23:28:16 media kernel: [260151.883961] sd 11:0:0:1: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) Jul 19 23:28:16 media kernel: [260151.884145] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.884570] sd 11:0:0:1: [sdc] Write Protect is off Jul 19 23:28:16 media kernel: [260151.884855] sd 11:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16). Jul 19 23:28:16 media kernel: [260151.885286] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.885807] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.909595] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.910159] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.910163] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.910167] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.910169] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.910172] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 Jul 19 23:28:16 media kernel: [260151.910182] quiet_error: 2 callbacks suppressed Jul 19 23:28:16 media kernel: [260151.910570] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.911153] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.911156] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.911159] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.911161] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.911164] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 Jul 19 23:28:16 media kernel: [260151.911385] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.911902] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.911905] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.911908] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.911910] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.911913] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 Jul 19 23:28:16 media kernel: [260151.912128] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.912650] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.912653] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.912656] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.912657] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.912660] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 Jul 19 23:28:16 media kernel: [260151.912876] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.913439] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.913442] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.913445] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.913446] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.913449] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 Jul 19 23:28:16 media kernel: [260151.945227] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.945863] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.945866] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.945870] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.945871] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.945875] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 (...) and so on for like 10 seconds until it gives up (...) 3. Question So, my question would be: what is causing this? Am I missing something, should I configure things differently, is this a known limitation? Searching online for more information did not yield any useful results... Thank you in advance for any help!

  Read the article

• Driver Scanner detect driver needed

  - by Pennf0lio

  Hi, I'm currently fixing the laptop of my friend. Her Laptop is kinda old and is not a well know brand (Redfox Navigator), So that means there are lack of support online. Are there Software that you install and will scan the system and will look for the driver that it needs? Note: The Laptop can't connect through the internet. thanks!

  Read the article

• How to configure Farsun USB barcode scanner to not auto-trigger

  - by David Grayson

  At my company we have several USB barcode scanners. I'm not sure exactly what model they are, but I think they are the FG9800 from Farsun because that's what they look like on the exterior. They came with a programming manual that is very similar to this document from the Farsun website. When I scan the "Output Firmware Version" barcode, my scanner types the following into the computer: Farsun V2.00 2011-01-01 Is it possible to configure these scanners so they only read barcodes in response to the trigger button being pressed? I don't want them to automatically read barcodes. Additionally, I want this setting to be remembered while the scanner is turned off. Since this scanner only has a USB port, the only way to configure it that I know of is to scan bar codes from the manual (or make your own). I have tried scanning the configuration bar codes for Single Scan (013300), Single Scan No Trigger (013301), and Laser/CCD Timeout - 5 Seconds (0134005) from this document. Sometimes (but not often) this puts the scanner in to the right mode, where it only scans when the button is pressed. Unfortunately, the scanner seems to always leave this mode when it is power cycled. I have also scanned the "Reset Configuration To Defaults" barcode (0B) many times. We have three different scanners like this and I have not been able to successfully configure any of them. If the things I want are not possible with these Farsun-based scanners, is there some other scanner we can use?

  Read the article

• Solaris: detect hotswap SATA disk insert

  - by growse

  What's the method used on Solaris to get the system to rescan for new disks that have been hot-plugged on a SATA controller? I've got an HP X1600 NAS which had 9 drives configred in a ZFS pool. I've added 3 disks, but the format command still only shows the original 9. When I plugged them in, I saw this: cpqary3: [ID 823470 kern.notice] NOTICE: Smart Array P212 Controller cpqary3: [ID 823470 kern.notice] Hot-plug drive inserted, Port=1I Box=1 Bay=12 cpqary3: [ID 479030 kern.notice] Configured Drive ? ....... NO cpqary3: [ID 100000 kern.notice] cpqary3: [ID 823470 kern.notice] NOTICE: Smart Array P212 Controller cpqary3: [ID 823470 kern.notice] Hot-plug drive inserted, Port=1I Box=1 Bay=11 cpqary3: [ID 479030 kern.notice] Configured Drive ? ....... NO cpqary3: [ID 100000 kern.notice] cpqary3: [ID 823470 kern.notice] NOTICE: Smart Array P212 Controller cpqary3: [ID 823470 kern.notice] Hot-plug drive inserted, Port=1I Box=1 Bay=10 cpqary3: [ID 479030 kern.notice] Configured Drive ? ....... NO But can't figure out how to get the format command to see them so I know they've been detected by the system.

  Read the article

• Auto Start of Proftpd on OpenSuse Linux

  - by a_ak

  I´m trying to activate the Ftpservice on my Root Server, i have OpenSuse installed, and I´m using the xinetd method .. i added this to my xineted.conf: service ftp { flags = REUSE socket_type = stream protocol = tcp wait = no user = root server = /usr/sbin/in.proftpd disable = no } I´m not sure about this "server = /usr/sbin/in.proftpd" .. i added the code directly in the xinetd.config and not in a seperate file.. and to my proftpd.conf as the documentation of profdtp ( was already setted) : ServerType inetd Then I restarted the xineted service .. and no errors to see, but the proftpd ist still not statrting/launching .. I searched alot on google, but everywhere they say to do what i did abouve, nothing more.. did i miss something ?

  Read the article

• Microsoft Security Essentials howto auto download definition updates

  - by chris.nullptr

  I use Microsoft Security Essentials as my antivirus on my Win7 box. New virus definitions to Security Essentials are installed using Windows Update. However, the updates are marked as optional by default, as opposed to important which means that they don't get installed automatically. I have to select the updates from the list of optional updates and install them manually. Is there a way to change this behavior so that new definitions are marked as important and installed automatically?

  Read the article

• Prevent auto mounting Android sdcard under Linux Mint

  - by BullShark

  I recently obtained an older Android phone, so that I could test Android Apps on it. I've needed it because I have a Nexus 7 but not older Android versions, hardware, etc. to test on. I'm having a problem with it under Linux Mint with Cinnamon. When I plug the phone in, or remove and plug the sdcard from the phone back to it while the phone is plugged in, Linux automatically mounts the sdcard. This is a problem because once it is mounted under Linux, it dismounts from the phone running Android 2.3.5, and I can no longer test Android Apps I write that require the sdcard to be present, writable. I went to Menu System Tools System Settings System Details Removable Media, and it brings up this window. I have changed the settings to always "Ask what to do" on "Select how media should be handled". However, the sdcard still gets mounted and then I am asked how I want to open these files (media players, photo importers, file browser, etc.). If I click the checkbox for "Never prompt or start programs on media insertion", then the sdcard is mounted, and I am not asked how to open these files. Eject is just a noob word for Ubuntu users that means umount (unmount) like "Adminstrator" is another ubuntu noob word for the root user. And if I unmount the sdcard, the phone doesn't recognize it again until I take the sdcard out and plug it back in. The phone sees it for a brief moment until Linux Mint takes it over. There are 2 possible solutions and maybe more: 1) Prevent Linux from automounting sdcards some how 2) Tell Android not to allow the computer it is plugged into to take over the sdcard, HOW? Edit: I found out how to prevent the sdcard from being automatically mounted: Now it gets recognized by Linux: bullshark@beastlinux ~ $ dmesg | tail -n 25 [597212.218323] sd 21:0:0:0: [sde] Attached SCSI removable disk [597212.218639] sr 21:0:0:1: Attached scsi CD-ROM sr2 [597212.218910] sr 21:0:0:1: Attached scsi generic sg7 type 5 [597217.139373] sd 21:0:0:0: [sde] 3862528 512-byte logical blocks: (1.97 GB/1.84 GiB) [597217.140726] sd 21:0:0:0: [sde] No Caching mode page present [597217.140735] sd 21:0:0:0: [sde] Assuming drive cache: write through [597217.143595] sd 21:0:0:0: [sde] No Caching mode page present [597217.143602] sd 21:0:0:0: [sde] Assuming drive cache: write through [597217.152240] sde: sde1 [597389.751008] 4:2:1: cannot get freq at ep 0x84 [597390.238742] 4:2:1: cannot get freq at ep 0x84 [597624.903132] sde: detected capacity change from 1977614336 to 0 [597637.677763] sd 21:0:0:0: [sde] 3862528 512-byte logical blocks: (1.97 GB/1.84 GiB) [597637.679616] sd 21:0:0:0: [sde] No Caching mode page present [597637.679626] sd 21:0:0:0: [sde] Assuming drive cache: write through [597637.682508] sd 21:0:0:0: [sde] No Caching mode page present [597637.682515] sd 21:0:0:0: [sde] Assuming drive cache: write through [597637.692758] sde: sde1 [597661.857979] sde: detected capacity change from 1977614336 to 0 [597688.775455] sd 21:0:0:0: [sde] 3862528 512-byte logical blocks: (1.97 GB/1.84 GiB) [597688.776814] sd 21:0:0:0: [sde] No Caching mode page present [597688.776823] sd 21:0:0:0: [sde] Assuming drive cache: write through [597688.780055] sd 21:0:0:0: [sde] No Caching mode page present [597688.780062] sd 21:0:0:0: [sde] Assuming drive cache: write through [597688.788639] sde: sde1 bullshark@beastlinux ~ $ However, the phone still unmounts the sdcard upon being detected by Linux. Linux detects but does not mount, and a few seconds later: Edit #2 (Solution): I solved this one by changing the usb connection type (was usb mass storage) :

  Read the article

• Mail.app doesn't detect sender in Address Book

  - by CoreSandello

  Hi there. I don't understand, how does 'smart addresses' in Mail.app work. Recently I mentioned, that for some emails I don't see person's full name in 'From' column. I started to dig into this behavior and found out, that I have few contacts in my Address Book, that are not recognized by Mail.app. Here how it looks: I have a person in Address Book with filled email entry and filled first/last name (localized). I have an incoming email from that person (from email specified in Address Book), but first/last name in the email itself doesn't match with ones specified in Address Book (e. g. 'From' field in email looks like 'John [work] <[email protected]>' while Address Book entry is 'John Smith' (localized, in Russian)). And Mail.app doesn't recognize that this mail is originating from that person in Address Book: if I click on 'From' field, it suggests to me to add sender to Address Book, while for others' emails I have 'Show in Address Book' menu entry (especially for ones with full localized name in 'From' field). I'm wondering, is that behavior correct or I'm missing something? I'm using Snow Leopard & Mail 4.0; my system language set to English, if that matters. I'd like to have some clarifications on that Mail.app behavior: whenever it fixable or not (and if it's fixable, I'd like to see a fix). By the way, is it possible to match sender's address against Address Book entry in filter rules or not? That would be great, if I can create rules like 'move all mail from that person to that folder' without specifying exact source address. Thanks, Ivan.

  Read the article

• Windows 8 auto-hibernate from sleep not working on Retina MacBook Pro

  - by frenchglen

  I have a similar question to this one. Only my context is the 15" Retina MacBook Pro - and Windows 8. I have just the original Mac OS X Mountain Lion on there, then Windows 8 via Bootcamp. no rEFIt installed. (I just press ALT every time I restart windows, actually as a security measure to stop tech-unsavvy thugs, who, if the laptop is stolen, think it's only a mac and don't discover my Windows as quickly as they would've, and by that time I remotely activate various anti-theft mac apps and nab them that way). SO: like the related question asks, why isn't it behaving like it should? The Windows 7 FAQ states: Will sleep eventually drain my laptop battery? If your laptop battery charge gets critically low while the computer is asleep, Windows automatically puts the laptop into hibernation mode. But this is just not happening - on my rMBP Windows 8. It seems EVERY time I set the laptop to sleep (when it reaches 10%), then arriving home and plugging it in and hoping to simply resume my work, it does NOT save the session to disk and I lose ALL my work. Who's fault is it? Win 8's (a bug, grr)? Or Apple's EFI system (maybe fixable via editing EFI options/do I have to install refit to make it work perhaps?) Or maybe changing windows power options can somehow fix the problem? Thanks for your help.

  Read the article

• Preventing auto-restart of nautilus on gnome 2.28

  - by Ivan Vucica

  Cheers! I dislike disobedience from my system. When I want to explicitly kill Nautilus with kill or killall, I am no longer able to do so. Previously I could disable this erroneous behavior (which even Windows do not exhibit!) through gnome-session-properties, however, it is no longer possible to set the "restart style" there (or whatever it was called). What is nowadays the correct way to disable nautilus autorestart under gnome? Reasons: I'm writing a piece of software that's painting directly into X11 root window. Nautilus is interfering. Compiz has a wallpapers plugin which Nautilus is painting over.

  Read the article

• Auto Bcc using amavis

  - by hitesh-4259

  Hi, I have installed amavisd-new ,spamassissin , postfix server. I want to implement the autobcc feature using amavisd. so please help me. Thanks in advance...

  Read the article

• Configuring zsh in OSX to auto start processes

  - by calumbrodie

  I've recently converted to using zsh instead of bash in OSX and was wondering if it is possible to do the following: When I launch my terminal I would like to start various tabs and have each tab run a different process e.g tailing logs, running ruby scripts etc. Currently I need to cmd+n multiple tabs and then manually start each process. While this doesn't take long I would like to be able to just launch my terminal and have these various tabs start and run those commands automatically. Is this possible?

  Read the article

• ssh auto-forward?

  - by Jakobud

  I'm not sure if there is a specific name for this type of activity or not, but anyways: When a user ssh's into machine1, is there someway to force them to automatically ssh to machine2? For example, if user Bob ssh's into server1, can you set something up on server1 so that when Bob successfully logs in, he automatically ssh's to server2, so that he only has access to server2 and isn't really able to do anything on server1? Also, when he exits, it would disconnect him from server2 but also server1. Does that make sense? Is that possible?

  Read the article

• My EliteBook is not auto picking 1080p for external monitor, poor display on forcing

  - by Griever

  I'm connecting my Samsung LED S22A300B to my HP EliteBook 6930p through VGA out. Laptop has Intel 4500MHD video card. I have latest drivers installed for both card and monitor. Only 800x600 and 1024x768 are shown. A lot of other people get this problem when they use it with docking station as discussed here. But I am not using any docking station. The monitor works great with my desktop though. As advised on the aforementioned page, one of the things I tried was to force the resolution using Intel's "custom resolution" feature. I installed PowerStrip on my desktop and copied advanced timing values(front/back porch,sync width, etc.) from there and then used the same values while defining a custom resolution in my laptop's Intel graphics utility. As a result, I got the 1080p resolution but the display is poor. Text has some weird colored shadow and sometimes on images too. What should I do?

  Read the article

• Make Virtualhost detect Wildcard with and without preceding www

  - by jasondavis

  In my Apache (Xampp) httpd-vhosts.conf file I have added this Virtualhost It allows me to use Wildcard names like testserver1.dev and testserver2.dev I just have to make sure to add the name to my Windows Hosts file. <VirtualHost *:80> VirtualDocumentRoot E:/Server/htdocs/projects/%1/www ServerAlias *.dev </VirtualHost> What I would like to do though is add to this funtionality and make it work if the name begins with a www so testserver1.dev would also work as www.testserver1.dev The way it currently is set up, if I tried to access that URL, it would look in a folder called www.testserver1 instead of the folder testserver1

  Read the article

• mdadm auto grow raid

  - by johannes

  I have a raid0/1 on lvm logical volumes. I resized the logical volumes. Now I want to resize the raid to use the complete logical volumes. This can be done with mdadm /dev/md? --grow -z newsize But somehow I can't figure out how to calculate the newsize argument. Is there a way to tell mdadm to grow to the biggest possible size? If not, how do I calculate the biggest possible size of the raid to use for the newsize argument?

  Read the article

• auto copy newest folders and images in MyPictures folder to USB drive

  - by TVersmet

  I drop lots of photos in a day into the My Documents/My Pictures folder. I archive at the end of each day to USB drives, to be stored offsite. What I would like is someway to automate the process. By example, a small app or script I can simply double-click and it will scan the My Pictures folder for the newest folders and images and copy them to the USB drive until the drive is full. It doesn't matter if I get redundancy from the previous days saved images, so long as the newest images and folders are always the first to get copied. Well, that's my request. Thanks for reading.

  Read the article

• ipod touch/iphone app to auto-login to wifi

  - by anonymous

  I am getting increasingly annoyed at wifi networks that require the user to fill in a login/pass by opening a browser. Are there any apps for iphone/ipod touch that are able to automate this step?

  Read the article

• Custom Filter in cPanel to Auto-Delete Emails with Russian Characters

  - by John Conde

  I get a lot of spam to my email account from Russia. The emails themselves (name, subject, body) are in Russian and I was hoping to create a custom filter in cPanel (not in SpamAssassin but in cPanel itself) to catch these emails and delete them before they hit my inbox. I've tried setting up rules to flag emails with these characters but they still are getting through. This leads me to believe that there is an encoding issue at play here. Unfortunately I do not know how to overcome this. Ideas?

  Read the article

• How do I detect if uTorrent is downloading?

  - by Richard

  I need to write a script that determines whether or not uTorrent is currently downloading something. I'd rather it just be downloading, but if I cannot differentiate between downloading and uploading then it would be better than nothing. One possible way would be check the whether any files ending in .!ut are locked - but I'm hoping for something a little more elegant. My weapon of choice is VBScript but I'm happy to use the command line if needs be.

  Read the article

• Script to Auto delete files older than a few minutes in ubuntu

  - by dassouki

  is there a shell script out there that deletes all files in a folder that are older than x minutes?

  Read the article

• Free Download Manager Auto-Upload

  - by concerned_parent

  Does Free Download Manager automatically upload my torrents when I download them? If so, is there a way to prevent it?

  Read the article

• How can I get Transaction Logs to auto-truncate after Backup

  - by Yaakov Ellis

  Setup: Sql Server 2008 R2, databases set up with Full recovery mode. I have set up a maintenance plan that backs up the transaction logs for a number of databases on the server. It is set to create backup files in sub-directories for each database, verify backup integrity is turned on, and backup compression is used. The job is set to run once every 2 hours during business hours (8am-6pm). I have tested the job and it runs fine, creates the log backup files as it should. However, from what I have read, once the transaction log is backed up, it should be ok to truncate the transaction log. I do not see any option for doing this in the Sql Server Maintenance Plan designer. How can I set this up?

  Read the article

• How to detect hard disk failure?

  - by Devator

  So, one of my servers has a hard disk failure. It's running software RAID, the system locked up and according to /proc/mdstat (and /var/log/messages), it's really down: Personalities : [raid1] md2 : active raid1 sdb2[1] 104320 blocks [2/1] [_U] md5 : active raid1 sdb5[1] 2104448 blocks [2/1] [_U] md6 : active raid1 sdb6[1] 830134656 blocks [2/1] [_U] md1 : active raid1 sdb1[1] 143363968 blocks [2/1] [_U] and Nov 5 22:04:37 m38501 smartd[4467]: Device: /dev/sda, not capable of SMART self-check However when I do smartctl -H /dev/sda, it passes the test. It also passes the test with smartctl --test=short /dev/sda. So, is smartctl a broken testing tool, or am I doing something completely off?

  Read the article

• mod_jk fails to detect error state because JBoss gives 404, not 500

  - by Ilya Sher

  Configuration: Apache + mod_jk, several workers on other machines (load balancing). When JBoss fails to deploy an application for example because of failed connection to the database, requests to /myapp/somepage generate 404. How do I configure JBoss to return 500 for everything under /myapp when the application failed to deploy? Additional info: Since 404 is not an "error state" code, mod_jk does not mark the worker as failed and continues to route the traffic there. Since there might be valid requests to this application also generating 404, I can not configure mod_jk to treat 404 as an "error state"

  Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >