Search Results

Search found 1915 results on 77 pages for 'identical'.

Page 27/77 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

  • SAS disk performance drops a while after reboot.

    - by Flamewires
    So we have some workstations with identical hardware. The Fedora14 box has a couple weeks uptime and still get good performance. hdparm -tT /dev/sda /dev/sda: Timing cached reads: 21766 MB in 2.00 seconds = 10902.12 MB/sec Timing buffered disk reads: 586 MB in 3.00 seconds = 195.20 MB/sec The Cent 5.5 boxes however seem to be okay after a reboot, /dev/sda: Timing cached reads: 34636 MB in 2.00 seconds = 17354.64 MB/sec Timing buffered disk reads: 498 MB in 3.01 seconds = 165.62 MB/sec but some time later( unsure exactly, tested at approx 1 day uptime) /dev/sda: Timing cached reads: 2132 MB in 2.00 seconds = 1064.96 MB/sec Timing buffered disk reads: 160 MB in 3.01 seconds = 53.16 MB/sec drop to this. This is with very low load. I believe they all have the same bios settings. Any ideas what could cause this on Cent? Ask for more info. It might also be worth noting, that passing the --direct flag causes the slow boxes to perform similarly to the non-slow ones for buffered disk reads.

    Read the article

  • MPlayer refuses to generate mono wav file

    - by JCCyC
    I want to downsample an existing audio file to 8KHz mono. This command line downsamples it to stereo: mplayer -quiet -vo null -vc dummy -af volume=0,resample=8000:0:1 -ao pcm:waveheader:file="/tmp/blah1.wav" ~/from_my_cellphone.3ga It generates a file that the file utility identifies as stereo: $ file /tmp/blah1.wav /tmp/blah1.wav: RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, stereo 8000 Hz Now, if I read the documentation correctly, I should add pan=1:0.5:0.5 so I get a file that's half the size: mplayer -quiet -vo null -vc dummy -af volume=0,resample=8000:0:1:pan=1:0.5:0.5 -ao pcm:waveheader:file="/tmp/blah2.wav" ~/from_my_cellphone.3ga But it doesn't! blah2.wav is identical to blah1.wav! What am I doing wrong?

    Read the article

  • Realtek "Microphone Effects" no longer working

    - by abc
    I have a mic plugged into my computer, and I was able to use the "microphone effects" tab here to enable/disable noise suppression and acoustic echo cancellation. Noise suppression off and acoustic echo cancellation on were the most recent settings I had on before the problem occurred. I disabled my mic in the windows 7 "recording devices" tab, then re-enabled it. When it came back, these options were grayed out, and remained so even after a reboot. I am not sure why this is or how to fix it, all other options are still the same (Settings are identical to when it was working). Any ideas whats wrong or how to fix it? edit: can't post image due to being new.

    Read the article

  • Missing menu items for Azure SQL tables within SQL Server Management Studio?

    - by Sid
    I have a table (say Table1) that is replicated via SQL Data Sync Agent across a local SQL Server 2012 as well as an Azure SQL Server (part of Microsoft Azure). Everything about Table1 (schema, table values etc ) is identical to the best of my understanding. However, when I list and right click Table1 from Microsoft SQL Server Management Studio 2012 (SSMS), I get some very different menu options, even for seemingly basic stuff. Lets focus only on the 'Design' menu item: It is visible for Table1 on the local SQL server in SSMS It is missing for Table1 on Azure SQL via SSMS It is visible for Table1 (as Open Table Definition) on Azure SQL when reaching it via Visual Studio 2012 (Server Explorer - Data connections) This is seen in the screenshots below: Now I use scripts from some real stuff (esp when I need to check in the SQL scripts etc) but this difference concerns me to some extent. Am I witnessing just a tools artifact in SQL Server Management Studio when connecting to Azure SQL? or is it something more serious about limitations of Azure SQL itself (although, just seeing the Design surface is so basic!)?

    Read the article

  • Server speed: sharing one script.php or using many copies the same script.php

    - by Marco Demaio
    Let's assume: I have thousands of domains on same Apache server. Each domain is in a folder under server public_html document folder, so it can be accessed by calling "www.somedomain.com" or by calling "www.serverdomain.com/somedomain_folder" In each domain there is a website who needs a certain script.php (identical for each domain). From a coding point view, its obvious that it's better to use a unique script.php, so when i update it with new features/bug fixes etc, I need to update on server only one file and it will work for all domains. But from a server point of view? If i use a unique script all domains will access it at the same time, will the server run slower compared to the situation where each domain called its own script?

    Read the article

  • AuthInfoRequired cups overwrites

    - by mooscape
    My problem is basically identical to the following: http://bbs.archlinux.org/viewtopic.php?id=61826 Put simply, I have a machine in ubuntu trying to connect to another ubuntu machine via a network in order to use the printer attached. There is no problem printing until I restart the guest machine. Immediately it overwrites the printers.conf file (under /etc/cups/printers.conf). It always adds the same line: AuthInfoRequired username,password I stop cups and change it to *#*AuthInfoRequired username,password to comment out the command. Start cups. Works great 'til the next shutdown. Then it gets overwritten again. Googling indicates it may be GTK problem and not CUPS, but I have found no permanent solution to date. Any suggestions appreciated ....

    Read the article

  • Best Server Ghost-Like Tool For Windows

    - by John Dibling
    I'm looking for advice on which tool we should use to clone servers. In the short term, we will be cloning identical hardware but in the long run we may want to create one image and replicate that on a different class of machine. For example, as new servers are released from Dell, we will want to continue to use the same image we already made. Right now our servers are Windows (Server 2008 & Server 2008 R2), but moving forward we may need Linux support as well. Ghost Solution Suite 2.5 seems to be the canonical tool. Are there alternatives? Recommendations/reviews?

    Read the article

  • Web Farm Application deployment best practices

    - by rauts
    Hi All, We are having a web farm which hosts multiple ASP.Net applications. We typically have 4 servers on the farm. The dilemma which i am having is in terms of capacity issue of the farm. Lets say i have currently got 200 apps in total. Should I deploy all 200 apps on all 4 servers (i.e. all the servers in the farm are identical) or should i split the applications between 2 sets of server and create 2 smaller farms so that i can then manage the application based on its criticality and usage etc. Any best practices in this area would be highly appreciated. Thanks Rauts

    Read the article

  • How can I join two simple home networks together using an ethernet cable?

    - by Ilia Jerebtsov
    I want to join two different home networks together like so: PC A1 PC A2 PC B1 PC B2 \ / \ / Gateway A <----- ethr. cable -----> Gateway B | | ADSL modem A ADSL modem B Both networks are of the basic residential type with identical configuration, with all PCs running Vista/7. The point is to temporarily join two apartments in a building for gaming and file sharing, and the holy grail would be: PCs on network A can access PCs on network B and vice-versa (file shares and gaming). Each network uses its own internet connection. Data between networks shouldn't take a trip through the internet (broadband upload speeds are severely capped) A network's internet access should continue working if the joining cable is disconnected with minimal configuration changes. How closely can this be achieved?

    Read the article

  • Windows Server Backup 2008 - Language Incompatibilities?

    - by Chris Walters
    I have 2 Windows 2008 Server R2 machines - one is Japanese language based and the other English. When I try to connect from the English language server using Windows Server Backup (snap-in) I get the following message: "An internal error has occurred in the backup engine or the computer that you are connected to remotely is running a version of backup application that is not compatible with the version on your local computer" Both claim to be running Version 1 of Windows Server Backup. Is remote connection to non-identical language server OSs a known problem? Specifically this is seen when attempting the "Connect To Another Server" in the action pane of Windows Server Backup.

    Read the article

  • Can Ping but Cannot Telnet directly to SQL Server 2012 Cluster Nodes

    - by tresstylez
    We have a monitoring tool (Solarwinds Orion) that needs to connect to a 2-node failover SQL Server Cluster. For reasons outside of our control -- we cannot monitor the CLUSTER IP directly at this time, so we have fallen back to monitoring each cluster node IP directly. This is not working. Upon troubleshooting, we tried to test that the cluster node was listening on the proper (fixed) port by using telnet to the cluster node IP/port -- and the telnet failed. However, telnet'ing to the Cluster IP/Port was SUCCESSFUL! Each node has its own IP. Each node is listening on the identical FIXED port. Each node has Dynamic Ports disabled. Each node can be PINGED successfully from the monitoring tool. Windows Firewall is DISABLED. How can I troubleshoot why I cannot telnet to the listening port on the cluster nodes?

    Read the article

  • Burning iso images with wodim loses 2048 bytes at the end

    - by Grumbel
    If I burn an iso image with: wodim -data dev=/dev/scd0 in.iso and then read it back out with: dd if=/dev/scd0 of=out.iso The resulting files are not identical, out.iso is 2048 bytes shorter then in.iso. What is going on here and how can I fix it? Using Ubuntu 10.04 and Wodim 1.1.10 PS: dd always ends with an Input/output error, not just with this CD, but with all of them. I think its just a limitation of dd, but an explanation why it happens and how to avoid it would be welcome as well.

    Read the article

  • Websphere 7: Getting 'Internal Server Error' when accessing JSPs. Servlets ok

    - by paul
    I have just installed WS 7 on our stage server. The test server was done some months ago. I have deployed the same applications to stage as on test. One application is causing me problems. I call the login servlet but the result is an 'Internal Server Error' message. From my logs I can see that the servlet processed the log in successfully and redirects to a JSP. That is the last message. I can find no further info in any of the other standard out/err logs. I have tried creating a simple JSP containing only HTML - same error. If I rename the file to test.html, it displays correctly. The plugin configuration appears to be identical with the one on the test server (where everything works) Ideas anyone?

    Read the article

  • Restoring file properties but not the complete files, from backup

    - by Jon
    While copying data from my old storage on a Linux computer to the new (linux-based) NAS, I accidentially failed with getting the properties (most important: the modify dates) along to the new location. I also continued to use/modify the files at the new location and hence, cannot just copy it all over again. What I would like to do is a diff between files in the old vs. the new storage, and for those being identical, restore the properties from Linux storage to the NAS storage files. Is there a clever way such as a script or a tool to do this? I could either run it on the Linux box or in worst case from a remote Windows computer. Grateful for any suggestions. /Jon

    Read the article

  • Can't deploy an ejb bean on jboss

    - by leo
    I am try to deploy a jar to an jboss server. It works on my environment. But when I deployed the same jar on another server, i kept getting an error saying that the persistence unit is already registered. There is no other bean using the same name and the same persistence unit name. I tried to restart the server and remove the tmp, work, data directory but still get the same error. here is my error: ObjectName: jboss.j2ee:service=EJB3,module=wess_jpa.jar State: FAILED Reason: java.lang.RuntimeException: javax.management.InstanceAlreadyExistsException: persistence.units:unitName=dses_wess already registered. This is almost identical to this issue in jboss forum but there is no solution: http://www.jboss.org/index.html?module=bb&op=viewtopic&p=4211687#4211687

    Read the article

  • How to move an existing Win7 setup to a RAID-1 array?

    - by Matthew Scharley
    Currently I have a the following setup: Drive A/B: Identical HDD's Drive C: 2TB external drive with plenty of space currently. Hardware RAID controller Currently I have Drive A which is my boot drive (Win7), and Drive C which is a data drive, and Drive B which I only recently received and is blank. What is the best way of moving off of Drive A, setting up the hardware RAID and then migrating my data back onto the RAID array? I'm proficient with Linux, but I'm not sure if I can get away with simply using dd here. There is currently enough free space on Drive C to take 5-6 copies of a disk image of Drive A, so space isn't an issue.

    Read the article

  • .bashrc doesn't get sourced after su'ing to root

    - by Ian Dunn
    I've got a CentOS 5.6 VPS and both root and my normal user account have identical copies of a .bashrc file in their home directories. The file contains a few basic aliases, etc. If I login to root, root's copy gets sourced. If I login to myuser, myuser's copy gets sourced If I su to root after logging into myuser, then all the aliases, etc inside myuser's copy get removed, and root's copy doesn't get sourced. If I then manually source root's copy, the command completes without any errors, but none of the aliases's etc get applied. I've searched Google and Server Fault, but haven't found any solutions. Does anyone know how to fix that?

    Read the article

  • what's POST code 18 / can I run an ASRock P55 Pro + Core i3 530?

    - by Michael Borgwardt
    When I switch my newly built PC on, the fans start up, but I get nothing on the monitor, and the POST display on the motherboard runs quickly through various codes and then stops at code 18, which does not appear in the manual (the list there seems identical to this one). This lasts about 10 seconds, after which the machine shuts down. After a pause (also about 10 seconds) it starts up again, and this repeats until I cut the power. Interestingly, when I push the reset button, it stops at POST code 16 (which is also not listed in the manual). Does anyone have information about the meaning of those codes? Motherboard: ASRock P55 Pro CPU: Intel Core i3 530 Graphics Card: Sapphire HHD 5750 Does anyone have experience with that Motherboard/CPU combination? It says on the packaging and in the manual that it's only compatible with Core i5 and i7 (no mention of i3), but on the maker's product page, the i3 is listed as compatible as well.

    Read the article

  • Second Monitor "Input Not Supported"

    - by Drew
    I have two identical monitors (new Acer s211hl) with a native resolution of 1920x1080. When enabling dual monitor support in Windows 7, the primary monitor works as expected, but the second monitor says, "Input not Supported" and fails to display anything. If I change the resolution of the second monitor to 1440x900, it works as expected. Likewise, if I set it to 1920x1080 with a refresh rate of 30hz, the monitor displays video. However, neither of these are solutions, because the output looks very blurry, and the content is stretched. I am using the following hardware: Monitors: Acer s211hl Motherboard: Asus F1A75M-Pro CPU/GPU: AMD A8-3850 with integrated Radeon HD 6550D graphics I suspect that there is probably an issue with the integrated graphics or motherboard not being able to output to two 1920x1080 monitors, but I am hoping for official confirmation.

    Read the article

  • Unable to run Microsoft Office 2010 install file

    - by Len
    This problem began when I noticed that the icons in the Windows 7 task bar for MS Word and Outlook were generic. I rebuilt the icon cache. Still not the right icons, but not the generic "document" icons either, and both are identical (to each other). The two programs seem to be working OK. So then I tried to repair MS Office. I ran the setup file. It extracts the files, I get the splash screen, and then the message, "Setup has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available." with a "Close program" button. Microsoft does not notify me about a solution. What I have tried: 1. running two other copies of the setup program; 2. doing an in-place re-install of Windows 7.

    Read the article

  • Hyper V cluster - one VM won't migrate

    - by Chris W
    We have a Failover Cluster built up on 6 blades, each running Hyper V. Each box is running Server 2008 R2. We've got a number of VMs running that all have the same basic config: VHD stored on a cluster shared volume. 2 virtual NICs (1 for LAN connection and 1 for SAN connection). All of our VMs will happily migrate between any other blade apart from one single VM which is running fine on it's current blade but will not migrate to any other location. What could be the cause of it or where should I look to get a detailed error message as I can't seem to find much information logged in any of the logs. Edit: I know the usual culprit is mis-matching resource names. We've already been there with the NICs named differently on some of the blades. As far as we can tell now everything looks to be identical on each bit of metal.

    Read the article

  • Config deployment on multiple servers.

    - by user66601
    I have multiple servers in WEB cluster (identical configuration for all of them, despite the IP) How do you deploy changes in configs on multile servers? I make the new config, then create config per every server (placing correct IP), and next: upload them on every server, replacing old ones (rsync over ssh) set on every server a job which reloads webserver at the same time (servers use ntp). - this done by issuing commands by script (to save time for logging in) before adding a job for server reload - there's checksum test of the config on the server) - an a notification in case of fail How do you see such method? What should be the "professional way :) ? (I don't say my way doesn't work... it works and saves my time not used for logging on every webserver.) Regards,

    Read the article

  • Is it possible to replace the Logitech G500 wire without rebuying the mouse?

    - by leladax
    It has to be replaced ideally in whole, from the point it starts inside the mouse (with a white 4-5 piece of wires connection) to the end (of the USB connector to the computer) or at least to a considerable length because there is fatigue very near the mouse and the more I fix it there with soldering the closer it gets to being unfixable or reaching towards 'inside' the mouse where fixing it will be hard or impossible. So I wonder if there is a way to get a replacement of the whole thing or at least the inside-the-mouse connector to a certain length. Also I wonder if other mice types are identical in the connector of the inside.

    Read the article

  • Micrsoft fax server not seeing new modem

    - by Tim Meers
    I recently added a new modem (a plain ol consumer grade one) to a fax server thats been up and running for years running on Microsoft Server 2003 fax services. The server currently has two modems, the new one is identical to one of the existing. After installing the new modem it showed up in the Fax Server Manager as a device but was not doing outbound faxes. (The server by default does not handle incoming.) So after a reboot the server no loger sees the modem in the Fax Server Manager but is listed as a device in device manager. I've attempted to restart just the fax service and even the whole box again but to no avail. Any one have any ideas on this one? Or any one with good links to resources for the fax service?

    Read the article

  • Comparing two strings in excel, add value for common variables

    - by overtime
    I'm comparing two large datasets containing strings in excel. Column A contains the numbers 1-1,000,000. Column B contains 1,000,000 strings, neatly organized in the desired order. Column C contains 100,000 randomly organized strings, that have identical values somewhere in column B. Example: A B C D 1 String1 String642 2 String2 String11 3 String3 String8000 4 String4 String78 What I'd like to do is find duplicate values in columns B and C then output the Column A value that corresponds with the string in Column C into Column D. Desired Output: A B C D 1 String1 String642 642 2 String2 String11 11 3 String3 String8000 8000 4 String4 String78 78

    Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >