Search Results

Search found 1054 results on 43 pages for 'reserved'.

Page 27/43 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

• Is wiper.sh working?

  - by Aleksander Blomskøld

  I'm setting up a server running Ubuntu Precise, and I'm trying to verify if SSD TRIM is working. fstrim is failing: ~ sudo fstrim -v / fstrim: /: FITRIM ioctl failed: Operation not supported So I tried wiper.sh in hdparm: wiper-3.5 sudo ./wiper.sh --verbose --commit /dev/sda1 wiper.sh: Linux SATA SSD TRIM utility, version 3.5, by Mark Lord. rootdev=/dev/sda1 fsmode2: fsmode=read-write /: fstype=ext4 freesize = 169502088 KB, reserved = 1695020 KB Preparing for online TRIM of free space on /dev/sda1 (ext4 mounted read-write at /). This operation could silently destroy your data. Are you sure (y/N)? y Creating temporary file (167807068 KB).. Syncing disks.. Beginning TRIM operations.. get_trimlist=/sbin/hdparm --fibmap WIPER_TMPFILE.11503 /dev/sda: trimming 3211263 sectors from 64 ranges succeeded trimming 3571713 sectors from 64 ranges succeeded trimming 3915776 sectors from 64 ranges succeeded (...) trimming 3657913 sectors from 60 ranges succeeded Removing temporary file.. Syncing disks.. Done. It seems to be working, but I'm wondering if it really is. Are there any cases where wiper.sh should work when fstrim isn't? Is there any way I can check if the TRIMing actually has succeeded (other than trusting the wiper.sh-log)?

  Read the article

• Configure IIS Web Site for alternate Port and receive Access Permission error

  - by Andrew J. Brehm

  When I configure IIS to run a Web site on Port 1414, I get the following error: --------------------------- Internet Information Services (IIS) Manager --------------------------- The process cannot access the file because it is being used by another process. (Exception from HRESULT: 0x80070020) However, as according to netstat the port is not in use. Completely aside from IIS, I wrote a test program (just to open the port and test it): TcpListener tcpListener; tcpListener = new TcpListener(IPAddress.Any, port); try { tcpListener.Start(); Console.WriteLine("Press \"q\" key to quit."); ConsoleKeyInfo key; do { key = Console.ReadKey(); } while (key.KeyChar != 'q'); } catch (Exception ex) { Console.WriteLine(ex.Message); } tcpListener.Stop(); The result was an exception and the following ex.Message: An attempt was made to access a socket in a way forbidden by its access permissions The port was available but its "access permissions" are not allowing me access. This remains after several restarts. The port is not reserved or in use as far as I know and while IIS says it is in use, netstat and my test program say it is not and my test program receives the error that I am not allowed to access the port. The test program ran elevated. The IIS Site is running MQSeries, but the MQ listener also cannot start on port 1414 because of this issue. A quick search of my registry found nothing interesting for port 1414. What are socket access permissions and how can I correct mine to allow access?

  Read the article

• Hugepages not utilized by MySQL 5.0, CentOS 5

  - by TechZilla

  I've set up Hugepages, but i'm not seeing any of them reserved. Have I missed a step, or for some particular reason, is MySQL is unable to utilize the Hugepages? I have not created a mount of hugetlbfs, although from what I read, MySQL would not call pages in such a manner. If I'm wrong, please let me know, as that would be a trivial solution. Almost all my MySQL tables are using InnoDB. NOTE: I created a hugetlbfs, no change as expected. Is it possible that rebooting would rectify this situation? I would not want to go through the procedure, as this is high availability, but would do so if necessary. This is the configurations, which I believe are relevant. /etc/sysctl.conf ... ## Huge Pages vm.nr_hugepages = 4096 vm.hugetlb_shm_group = 27 ## SHM kernel.shmmax = 34359738368 kernel.shmall = 8589934592 ... /etc/security/limits.conf ... mysql soft nofile 12888 mysql hard nofile 51552 @mysql soft memlock unlimited @mysql hard memlock unlimited /etc/my.cnf [mysqld] large-pages ... grep Huge /proc/meminfo HugePages_Total: 4096 HugePages_Free: 4096 HugePages_Rsvd: 0 Hugepagesize: 2048 kB id mysql uid=27(mysql) gid=27(mysql) groups=27(mysql) context=root:system_r:unconfined_t:SystemLow-SystemHigh tail -6 /var/log/mysqld.log InnoDB: HugeTLB: Warning: Failed to allocate 1342193664 bytes. errno 12 InnoDB HugeTLB: Warning: Using conventional memory pool 120808 15:49:25 InnoDB: Started; log sequence number 0 1729804158 120808 15:49:25 [Note] /usr/libexec/mysqld: ready for connections. Version: '5.0.95' socket: '/var/lib/mysql/mysql.sock' port: 3306 Source distribution I would really appreciate any help, I'm completely out of ideas. If I missed any more relevant configs, or diagnostics, please comment and I'll add it to the question.

  Read the article

• Sparing level on HP EVA 4000

  - by Samuel

  One of the disks of our EVA4000 died today. This diskgroup (all volumes vraid5 with sparing level 1 and almost no space left for more volumes, 1TiB drives) is being rebuilt with "spare space" right now, and it will take at least 15 hours to do the leveling/rebuilding. We can't get a new disk until Friday. So, the question is, what would happen if another disk dies before the leveling completes? Would we lose data? And after that, how many aditional disks could die before losing data? 1 or 2? In "usual" RAID, we would be vulnerable to data loss while the rebuild takes place, but in this case the space reserved for sparing is two times the size of the bigger disk, so at the very least the effect should be the same of having two spares. Thanks in advance. Update: I have found some interesting threads about this question but still can't answer to this question, so I'm starting a bounty. http://blog.thestoragearchitect.com/2008/10/27/understanding-eva/ http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&url=http%3A%2F%2Fwww.experts-exchange.com%2FStorage%2FStorage_Technology%2FQ_25548177.html (Expert Exchange question from google).

  Read the article

• Creating an ec2 image on amazon fails at mkfs.ext3

  - by Dave Orr

  I'm trying to create an image of my ec2 instance in Amazon's cloud. It's been a bit of an adventure so far. I did manage to install Amazon's ec2-api-tools, which was harder than it seemed like it should have been. Then I ran: ec2-bundle-vol -d /mnt -k pk-{key}.pem -c cert-{cert}.pem -u {uid} -s 1536 Which returned: Copying / into the image file /mnt/image... Excluding: /sys/kernel/debug /sys/kernel/security /sys /proc /dev/pts /dev /dev /media /mnt /proc /sys /etc/udev/rules.d/70-persistent-net.rules /etc/udev/rules.d/z25_persistent-net.rules /mnt/image /mnt/img-mnt 1+0 records in 1+0 records out 1048576 bytes (1.0 MB) copied, 0.00677357 s, 155 MB/s mkfs.ext3: option requires an argument -- 'L' Usage: mkfs.ext3 [-c|-l filename] [-b block-size] [-f fragment-size] [-i bytes-per-inode] [-I inode-size] [-J journal-options] [-G meta group size] [-N number-of-inodes] [-m reserved-blocks-percentage] [-o creator-os] [-g blocks-per-group] [-L volume-label] [-M last-mounted-directory] [-O feature[,...]] [-r fs-revision] [-E extended-option[,...]] [-T fs-type] [-U UUID] [-jnqvFKSV] device [blocks-count] ERROR: execution failed: "mkfs.ext3 -F /mnt/image -U 1c001580-9118-4a50-9a25-dcf02be6d25f -L " So mkfs.ext3 wants -L, which is a volume name. But ec2-bundle-vol doesn't seem to take in a volume name as an argument, and the docs (http://docs.amazonwebservices.com/AmazonEC2/gsg/2006-06-26/creating-an-image.html) don't seem to think one should be needed. Certainly their sample command: # ec2-bundle-vol -d /mnt -k ~root/pk-HKZYKTAIG2ECMXYIBH3HXV4ZBZQ55CLO.pem -u 495219933132 -s 1536 doesn't specify anything. So... any help? What am I missing?

  Read the article

• How do you recreate the System Recovery environment in Windows 7?

  - by Howiecamp

  I'm running Windows 7 Home Premium RTM (64-bit) and I want to take advantage of the system recovery tools (eg the Command Prompt) without using the Windows 7 DVD. My understanding is that this environment (WinRE) should be installed to your HDD by default as part of the Windows 7 installation. However, when I hit F8 on boot and select "Repair", I get: Windows failed to start. A recent hardware or software change might be the cause. To fix the problem... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. The "Info" line seems like the smoking gun. My next step was to boot from the Windows 7 DVD, and choose "Repair". It indicated my Recovery Environment wasn't on the Windows 7 boot menu (perfect) and offered to fix it. I said yes and rebooted, however same issue as above. In addition, when I booted in to Windows 7 and I looked at the boot menu options, the recovery/repair option was not there. Only my Windows installation. Finally, I ran the Disk Management tool (diskmgmt.msc) and took a look at the contents of my "System Reserved" partition (which was set to "Active" as normal). It's unclear to me what the contents should look like, however it is my understanding that the WinRE environment gets installed to this partition. (As part of the above troubleshooting I followed http://superuser.com/questions/25728/how-to-fix-windows-7-boot-process which lead to http://www.sevenforums.com/tutorials/668-system-recovery-options.html).

  Read the article

• Win2008: Boot from mirrored dynamic disk fails!

  - by Daniel Marschall

  Hello. I am using Windows Server 2008 R2 Datacenter and I got two 1.5TB S-ATA2 hard disks installed and I want to make a soft raid. (I do know the disadvantages of softraid vs. hardraid) I have following partitions on Disk 0: (1) Microsoft Reserved 100 MB (dynamic), created during setup (2) System Partition 100 GB (dynamic) (3) Data partition, 1.2TB (dynamic) I already mirrored these contents to Disk 1. Its contents are: (1) System partition mirror, 100 GB (dynamic) (2) Data partition, 1.2 TB mirror (dynamic) (3) Unusued 100 MB (dynamic) -- is from "MSR" of Disk 0, created during setup. Since data and system partition are mirrored, I expect that my system works if disk 0 would fail. But it doesn't. If I force booting on disk 0: Works (I get the 2 bootloader screen) If I force booting on disk 1 (F8 for BBS), nothing happens. I got a blank black screen with the blinking caret. I already made disk1/partition1 active with diskpart, but it still does not boot from this drive. Please help. Both partitions are in "MBR" partition style. They look equal, except the missing "MSR" partition at the partition beginning (which seems to be not relevant to booting). Regards Daniel Marschall

  Read the article

• WMI Sensors monitoring

  - by DmitrySemenov

  Monitoring tool Paessler stopped to monitor WMI Windows Sensors Paessler is Updated to version 12.4.5.3165. (10/30/2012 1:44:11 PM) Paessler windows sensors (against windows server 2008 R2 web edition) stopped to work (no changes have been made on server that we monitor) with the message Connection could not be established (80070005: Access is denied - Host: 192.168.2.10, User: Administrator, Password: **, Domain: ntlmdomain:) (code: PE015) However if I go to Virtual machine used to run Paessler and the following cscript runs successfully: strComputer = "192.168.2.10" Set objSWbemLocator = CreateObject("WbemScripting.SWbemLocator") Set objSWbemServices = objSWbemLocator.ConnectServer _ (strComputer, "root\cimv2", _ "Administrator", "pass") Set colProcessList = objSWbemServices.ExecQuery( _ "Select * From Win32_Processor") For Each objProcess in colProcessList Wscript.Echo "Process Name: " & objProcess.Name Next I'm getting output C:\>cscript test.vbs Microsoft (R) Windows Script Host Version 5.8 Copyright (C) Microsoft Corporation. All rights reserved. Process Name: Intel(R) Xeon(R) CPU X5680 @ 3.33GHz Process Name: Intel(R) Xeon(R) CPU X5680 @ 3.33GHz So WMI works a. I gave Administrator credentials for Device to monitor in Paessler setting, the same I used in the script above b. I restarted windows server (broken sensors) - but this didn't help c. I restarted Paessler probe service - no effect any ideas?

  Read the article

• Windows 7 Explorer keeps crashing

  - by Daniel Liang

  I currently have an issue with Windows Explorer. It keeps crashing when I browse through a network drive. This is happening on several computers. I have already obtained a crash dump file but it doesn't state much: Microsoft (R) Windows Debugger Version 6.12.0002.633 X86 Copyright (c) Microsoft Corporation. All rights reserved. Loading Dump File [C:\LocalDumps\explorer.exe.3964.dmp] User Mini Dump File with Full Memory: Only application data is available Symbol search path is: SRV*c:\websymbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Version 7601 (Service Pack 1) MP (2 procs) Free x86 compatible Product: WinNt, suite: SingleUserTS Machine Name: Debug session time: Mon Oct 21 11:21:30.000 2013 (UTC - 4:00) System Uptime: 0 days 0:06:20.449 Process Uptime: 0 days 0:05:54.000 ................................................................ ................................................................ .... Loading unloaded module list ............. This dump file has an exception of interest stored in it. The stored exception information can be accessed via .ecxr. (f7c.fe4): Access violation - code c0000005 (first/second chance not available) eax=00000000 ebx=07a3f080 ecx=00000400 edx=00000000 esi=00000002 edi=00000000 eip=76e170f4 esp=07a3f030 ebp=07a3f0cc iopl=0 nv up ei pl zr na pe nc cs=001b ss=0023 ds=0023 es=0023 fs=003b gs=0000 efl=00000246 ntdll!KiFastSystemCallRet: 76e170f4 c3 ret I've already tried removing certain context menu items. I disabled all unnecessary start-up items. Ran memtest86 and it looks fine on that end. It also happens when I browse through my local disk. Can anyone take a look into this? Thanks!

  Read the article

• Dell OMCI: Wacky values for Temperature and etc? (Win7x64)

  - by Yablargo

  Hey All. I am running a Dell Precision R5400 Workstation with dell OMCI installed. I am using it to test polling various data over WMI for our monitoring across the enterprise. I'm getting some weird results. perhaps someone can help point me in the direction of some clarification? Posted is the results of my DCIM\SYSMAN\DCIM_NumericSensor probe for sensor type 2(temp sensor) Microsoft (R) Windows Script Host Version 5.8 Copyright (C) Microsoft Corporation. All rights reserved. ----------------------------------- DCIM_NumericSensor instance ----------------------------------- Accuracy: AccuracyUnits: AdditionalAvailability: Availability: AvailableRequestedStates: BaseUnits: 2 Caption: CommunicationStatus: CreationClassName: DCIM_NumericSensor CurrentReading: -214748365 CurrentState: Unknown Description: DetailedStatus: DeviceID: Root/MainSystemChassis/TemperatureObj ElementName: Temperature Sensor:CPU0 EnabledDefault: 2 EnabledState: 2 EnabledThresholds: ErrorCleared: ErrorDescription: HealthState: 5 Hysteresis: IdentifyingDescriptions: InstallDate: IsLinear: LastErrorCode: LocationIndicator: LowerThresholdCritical: LowerThresholdFatal: LowerThresholdNonCritical: MaxQuiesceTime: MaxReadable: MinReadable: Name: NominalReading: NormalMax: NormalMin: OperatingStatus: OperationalStatus: 2 OtherEnabledState: OtherIdentifyingInfo: OtherSensorTypeDescription: PollingInterval: PossibleStates: Unknown,Normal,Fatal,Lower Non-Critical,Upper Non-Critical,Lower Critical,Upper Critical PowerManagementCapabilities: PowerManagementSupported: PowerOnHours: PrimaryStatus: ProgrammaticAccuracy: RateUnits: 0 RequestedState: 12 Resolution: SensorType: 2 SettableThresholds: Status: StatusDescriptions: StatusInfo: SupportedThresholds: SystemCreationClassName: DCIM_ComputerSystem SystemName: dt:5Q7BKK1 TimeOfLastStateChange: Tolerance: TotalPowerOnHours: TransitioningToState: 12 UnitModifier: 0 UpperThresholdCritical: UpperThresholdFatal: UpperThresholdNonCritical: ValueFormulation: 2 I'm not really sure whats going on, but note the CurrentReading: -214748365. I have reinstalled OMCI a few times, installed the OMCI 7x compatability and same thing I consistently get that error. It almost looks like its a issue between 32/64 bit value or something? Do I have to convert it to a float ? :)

  Read the article

• Connect to WEP Wireless Network by command line on Ubuntu

  - by Tim

  Hi, I am a newbie to both network and Linux. I am now trying to connect to a WEP wireless network by command line on my Ubuntu 8.10, because the Network Manager does not support 64 bit WEP. (1) I firstly bring down the Network Manager and then try to connect to a wireless network, whose essid is candy and password is 5673212741. But it fails as shown in the following. I wonder why and how to do it correctly? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwconfig wlan0 essid candy opendo iwconfig wlan0 key 18018ce78e open $ sudo iwconfig wlan0 key 5673212741 open $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 9971 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 20 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9 No DHCPOFFERS received. No working leases in persistent database - sleeping. $ ping www.bbc.co.uk ping: unknown host www.bbc.co.uk (2) A less important question: why the scan for wireless networ does not work after I bring down the Network Manager? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning : Network is down Thanks and regards!

  Read the article

• conflicting info about the running kernel version in FreeBSD

  - by John

  I asked a related question about uname before, now want to ask from another angle because the following simple yet obvious conflicting outputs may mean there is something many people did not think of (me included). I'm running FreeBSD 9 RELEASE, please see the following commands: # sysctl kern.bootfile kern.bootfile: /boot/kernel/kernel # strings /boot/kernel/kernel |grep RELEASE|grep 9 @(#)FreeBSD 9.2-RELEASE-p7 #0: Tue Jun 3 11:05:13 UTC 2014 FreeBSD 9.2-RELEASE-p7 #0: Tue Jun 3 11:05:13 UTC 2014 9.2-RELEASE-p7 The above kernel file suggests the running kernel is 9.2-RELEASE-p7. But... # dmesg Copyright (c) 1992-2012 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.1-RELEASE #0 r243825: Tue Dec 4 09:23:10 UTC 2012 ... # uname -a FreeBSD localhost.localdomain 9.1-RELEASE FreeBSD 9.1-RELEASE #0 r243825: Tue Dec 4 09:23:10 UTC 2012 [email protected]:/usr/obj/usr/src/sys/GENERIC amd64 So dmesg and uname says it's 9.1-RELEASE. I also did an extensive find / -type f -exec grep -l "9.1-RELEASE" {} \; but found no possible kernel file that contains 9.1-RELEASE. What could lead to the above conflict, and what kernel I am actually running? Please note I run RELEASE and ran freebsd-update to do binary update, so no compiled kernel is involved. And I have rebooted multiple times after freebsd-update. And the system is not in jail etc, just the only system on that computer.

  Read the article

• Connect to Nonencrypted Wireless Network Using Ubuntu Commands

  - by Tim

  I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

  Read the article

• ExpressCache not working after Windows 8 reinstall on Samsung Series 7 Gamer

  - by Morven

  I have a Samsung Series 7 Gamer laptop which came with Windows 8. After doing a reinstall of Windows, the ExpressCache software is no longer caching. Running "eccmd -info" shows me that the software is present and it has the MSATA drive partition configured. However, it's not actually caching anything. These are the results after having the system booted for days: C:\windows\system32eccmd -info ExpressCache Command Version 1.0.94.0 Copyright¬ 2010-2012 Condusiv Technologies. Date Time: 11/3/2013 12:26:20:263 (JAMETHIEL #36) EC Cache Info ================================================== Mounted : Yes Partition Size : 7.46 GB Reserved Size : 3.00 MB Volume Size : 7.46 GB Total Used Size : 86.50 MB Total Free Space : 7.38 GB Used Data Size : 16.63 MB Used Data Size on Disk : 84.38 MB Tiered Cache Stats ================================================== Memory in use : 32.00 MB Blocks in use : 136 Read Percent : 0.02% Cache Stats ================================================== Cache Volume Drive Number : 1 Total Read Count : 97242 Total Read Size : 4.13 GB Total Cache Read Count : 0 Total Cache Read Size : 595.50 KB Total Write Count : 161546 Total Write Size : 5.89 GB Total Cache Write Count : 0 Total Cache Write Size : 0 Bytes Cache Read Percent : 0.01% Cache Write Percent : 0.00% As you can see on the last two lines, cache read and write percent is nigh on zero. Anyone know where to look next? The only guides I can find deal with ExpressCache not being present or not having a configured drive.

  Read the article

• After upgrading to 2008 R2 Enterprise and installing more RAM, Windows can only see 4.00 GB

  - by Tom Crane

  (I have also posted this on technet but I'm running out of ideas) I've upgraded from Windows Server 2008 R2 Standard to Enterprise in order to make use of more RAM. The server previously had 32GB of RAM. The upgrade from Standard to Enterprise, using DISM, seemed to go OK, so I powered down and installed the RAM. This a Dell Poweredge T710, I was taking it from 32GB to 72GB. The BIOS recognised the RAM, although I needed to change from "Advanced ECC" to "Optimizer" mode for it to use all of it. After rebooting, windows can see the RAM but in the system panel will display: Installed memory (RAM): 72.0 GB (4.00 GB usable) In the resource monitor, the remainder of the RAM is showing as reserved for hardware. I've tried various RAM configurations, including reverting it to the same chips and same configuration as before the upgrade, but always just 4.00 GB is showing up as usable. Following some threads on these forums I've gone into msconfig and set the maximum memory "by hand" but that doesn't fix the problem. BIOS doesn't seem to have anything that looks like memory remapping which is another suggestion that has come up. How do I make this RAM available to Windows? It was available before the upgrade, because I could use the full 32GB RAM the server had to start with. A screenshot (this is after reverting to the original RAM configuration) http://screencast.com/t/5FuzevdNb I don't know if it's related, but my remote desktop configuration has also disappeared: screencast.com/t/mYedomeQWS (the bottom half of this dialog should allow me to configure Remote Desktop, it was working before the upgrade but now it isn't).

  Read the article

• diskmgmt.msc: Cannot delete volume from USB

  - by Notinlist

  I have an USB drive with about 8GB of size. It has a single partition of size 169MB. Don't know why, I got it that way. I wanted to delete this small (FAT32) partition and create a single NTFS volume on it. First, I noticed that the "Delete volumme" option is disabled (grayed out). I then tried "Change drive letter and paths..." and removed "F:", that way I made sure that there are no open files on it. The "Delete volume" was still disabled. Then I got suspicious, and right clicked on the "Unallocated" area and I noticed that I did not have any useful option. All "New * volume" items are disabled. I exited from diskmgmt.msc, ran a cmd.exe with administrator privileges, ran the diskmgmt.msc from it, same experiences. Why can't i do anything with this disk? I've read some advices about downloading some alternative free software, but I rather not do it if possible. I still hope that Windows 7 Enterprise 64bit alone can reinitialize an USB drive without external help. I also cannot do anything with my other 8GB pendrive. It's all an NTFS volume, I tried to delete it, but the option is disabled here too. Maybe I have some settings somewhere that prevents my from partitioning USB disks. (I have the freedom to remove my D: partition which is the second - not counding the "System reserved" - on my SSD disk.)

  Read the article

• Flash drive suddenly died. Why? Can I recover it?

  - by mg

  Hi, I have a flash drive that I used not too much but, after few month of inactivity, it died. I know that flash drives have a limited write cycles but I am sure that this is not the problem. I tried to create a new partition table and format the drive nothing worked. This is the output of mkfs.ext2. marco@pinguina:~$ sudo LANG=en.UTF-8 mkfs.ext2 -v -c /dev/sdc1 [sudo] password for marco: mke2fs 1.41.11 (14-Mar-2010) fs_types for mke2fs.conf resolution: 'ext2', 'default' Calling BLKDISCARD from 0 to 4001431552 failed. Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 244320 inodes, 976912 blocks 48845 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=1002438656 30 block groups 32768 blocks per group, 32768 fragments per group 8144 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Running command: badblocks -b 4096 -X -s /dev/sdc1 976911 badblocks: Input/output error during ext2fs_sync_device Checking for bad blocks (read-only test): done Block 0 in primary superblock/group descriptor area bad. Blocks 0 through 2 must be good in order to build a filesystem. Aborting.... Is there something I can do to recover it?

  Read the article

• Performance tweaks and upgrades for VMWare Server 2

  - by sjohnston

  Our software department has a server running VMWare Server 2. We typically have 8-10 VMs running as test environments (Win XP and Server 08) for various versions of our software, and one VM that is used as a build server (Win XP). The host is running Server 2003 R2. It has 32GB RAM, 8 core Xeon 3.16GHz CPU, one disk for host OS and two raid disks for VMs. The majority of the time, this setup behaves very well and there are no complaints. Other times, the VMs can be very laggy. This is sometimes, but not always, correlated to heavy load on the build server. I'm a software developer, not an IT pro, but it seems to me that this machine should be beefy enough to handle this many VMs. Is this occasional performance hit likely just because we're hitting the limits of the hardware, or should I be looking for another culprit? From what I've read, I'm guessing if there's a bottleneck, it's probably disk I/O with all these VMs running off two disks (especially the build server). Would spreading the VMs over more disks, and/or switching to SSDs give us a significant performance boost? Other things I've read may increase performance: single virtual processor per VM removing/disabling unused virtual hardware preallocated disk space not using snapshots setting a reserved memory limit on the host and disabling VM memory swapping Can anyone confirm or deny if any of these improve performance? What other good tweaks have I missed?

  Read the article

• Cannot open root device xvda1 or unknown-block(0,0)

  - by svoop

  I'm putting together a Dom0 and three DomU (all Gentoo) with kernel 3.5.7 and Xen 4.1.1. Each Dom has it's own md (md0 for Dom0, md1 for Dom1 etc). Dom0 works fine so far, however, I'm stuck trying to create DomUs. It appears the xvda1 device on DomU is not created or accessible: Parsing config file dom1 domainbuilder: detail: xc_dom_allocate: cmdline="root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3", features="(null)" domainbuilder: detail: xc_dom_kernel_mem: called domainbuilder: detail: xc_dom_boot_xen_init: ver 4.1, caps xen-3.0-x86_64 xen-3.0-x86_32p hvm-3.0-x86_32 hvm-3.0-x86_32p hvm-3.0-x86_64 domainbuilder: detail: xc_dom_parse_image: called domainbuilder: detail: xc_dom_find_loader: trying multiboot-binary loader ... domainbuilder: detail: loader probe failed domainbuilder: detail: xc_dom_find_loader: trying Linux bzImage loader ... domainbuilder: detail: xc_dom_malloc : 10530 kB domainbuilder: detail: xc_dom_do_gunzip: unzip ok, 0x2f7a4f -> 0xa48888 domainbuilder: detail: loader probe OK xc: detail: elf_parse_binary: phdr: paddr=0x1000000 memsz=0x558000 xc: detail: elf_parse_binary: phdr: paddr=0x1558000 memsz=0x690e8 xc: detail: elf_parse_binary: phdr: paddr=0x15c2000 memsz=0x127c0 xc: detail: elf_parse_binary: phdr: paddr=0x15d5000 memsz=0x533000 xc: detail: elf_parse_binary: memory: 0x1000000 -> 0x1b08000 xc: detail: elf_xen_parse_note: GUEST_OS = "linux" xc: detail: elf_xen_parse_note: GUEST_VERSION = "2.6" xc: detail: elf_xen_parse_note: XEN_VERSION = "xen-3.0" xc: detail: elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 xc: detail: elf_xen_parse_note: ENTRY = 0xffffffff815d5210 xc: detail: elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81001000 xc: detail: elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb" xc: detail: elf_xen_parse_note: PAE_MODE = "yes" xc: detail: elf_xen_parse_note: LOADER = "generic" xc: detail: elf_xen_parse_note: unknown xen elf note (0xd) xc: detail: elf_xen_parse_note: SUSPEND_CANCEL = 0x1 xc: detail: elf_xen_parse_note: HV_START_LOW = 0xffff800000000000 xc: detail: elf_xen_parse_note: PADDR_OFFSET = 0x0 xc: detail: elf_xen_addr_calc_check: addresses: xc: detail: virt_base = 0xffffffff80000000 xc: detail: elf_paddr_offset = 0x0 xc: detail: virt_offset = 0xffffffff80000000 xc: detail: virt_kstart = 0xffffffff81000000 xc: detail: virt_kend = 0xffffffff81b08000 xc: detail: virt_entry = 0xffffffff815d5210 xc: detail: p2m_base = 0xffffffffffffffff domainbuilder: detail: xc_dom_parse_elf_kernel: xen-3.0-x86_64: 0xffffffff81000000 -> 0xffffffff81b08000 domainbuilder: detail: xc_dom_mem_init: mem 5000 MB, pages 0x138800 pages, 4k each domainbuilder: detail: xc_dom_mem_init: 0x138800 pages domainbuilder: detail: xc_dom_boot_mem_init: called domainbuilder: detail: x86_compat: guest xen-3.0-x86_64, address size 64 domainbuilder: detail: xc_dom_malloc : 10000 kB domainbuilder: detail: xc_dom_build_image: called domainbuilder: detail: xc_dom_alloc_segment: kernel : 0xffffffff81000000 -> 0xffffffff81b08000 (pfn 0x1000 + 0xb08 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1000+0xb08 at 0x7fdec9b85000 xc: detail: elf_load_binary: phdr 0 at 0x0x7fdec9b85000 -> 0x0x7fdeca0dd000 xc: detail: elf_load_binary: phdr 1 at 0x0x7fdeca0dd000 -> 0x0x7fdeca1460e8 xc: detail: elf_load_binary: phdr 2 at 0x0x7fdeca147000 -> 0x0x7fdeca1597c0 xc: detail: elf_load_binary: phdr 3 at 0x0x7fdeca15a000 -> 0x0x7fdeca1cd000 domainbuilder: detail: xc_dom_alloc_segment: phys2mach : 0xffffffff81b08000 -> 0xffffffff824cc000 (pfn 0x1b08 + 0x9c4 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1b08+0x9c4 at 0x7fdec91c1000 domainbuilder: detail: xc_dom_alloc_page : start info : 0xffffffff824cc000 (pfn 0x24cc) domainbuilder: detail: xc_dom_alloc_page : xenstore : 0xffffffff824cd000 (pfn 0x24cd) domainbuilder: detail: xc_dom_alloc_page : console : 0xffffffff824ce000 (pfn 0x24ce) domainbuilder: detail: nr_page_tables: 0x0000ffffffffffff/48: 0xffff000000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x0000007fffffffff/39: 0xffffff8000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x000000003fffffff/30: 0xffffffff80000000 -> 0xffffffffbfffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x00000000001fffff/21: 0xffffffff80000000 -> 0xffffffff827fffff, 20 table(s) domainbuilder: detail: xc_dom_alloc_segment: page tables : 0xffffffff824cf000 -> 0xffffffff824e6000 (pfn 0x24cf + 0x17 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cf+0x17 at 0x7fdece676000 domainbuilder: detail: xc_dom_alloc_page : boot stack : 0xffffffff824e6000 (pfn 0x24e6) domainbuilder: detail: xc_dom_build_image : virt_alloc_end : 0xffffffff824e7000 domainbuilder: detail: xc_dom_build_image : virt_pgtab_end : 0xffffffff82800000 domainbuilder: detail: xc_dom_boot_image: called domainbuilder: detail: arch_setup_bootearly: doing nothing domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_64 <= matches domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32 domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_64 domainbuilder: detail: xc_dom_update_guest_p2m: dst 64bit, pages 0x138800 domainbuilder: detail: clear_page: pfn 0x24ce, mfn 0x37ddee domainbuilder: detail: clear_page: pfn 0x24cd, mfn 0x37ddef domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cc+0x1 at 0x7fdece675000 domainbuilder: detail: start_info_x86_64: called domainbuilder: detail: setup_hypercall_page: vaddr=0xffffffff81001000 pfn=0x1001 domainbuilder: detail: domain builder memory footprint domainbuilder: detail: allocated domainbuilder: detail: malloc : 20658 kB domainbuilder: detail: anon mmap : 0 bytes domainbuilder: detail: mapped domainbuilder: detail: file mmap : 0 bytes domainbuilder: detail: domU mmap : 21392 kB domainbuilder: detail: arch_setup_bootlate: shared_info: pfn 0x0, mfn 0xbaa6f domainbuilder: detail: shared_info_x86_64: called domainbuilder: detail: vcpu_x86_64: called domainbuilder: detail: vcpu_x86_64: cr3: pfn 0x24cf mfn 0x37dded domainbuilder: detail: launch_vm: called, ctxt=0x7fff224e4ea0 domainbuilder: detail: xc_dom_release: called Daemon running with PID 4639 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.5.7-gentoo (root@majordomo) (gcc version 4.5.4 (Gentoo 4.5.4 p1.0, pie-0.4.7) ) #1 SMP Tue Nov 20 10:49:51 CET 2012 [ 0.000000] Command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] ACPI in unprivileged domain disabled [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009ffff] usable [ 0.000000] Xen: [mem 0x00000000000a0000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000138ffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] MPS support code is not built-in. [ 0.000000] Using acpi=off or acpi=noirq or pci=noacpi may have problem [ 0.000000] DMI not present or invalid. [ 0.000000] No AGP bridge found [ 0.000000] e820: last_pfn = 0x139000 max_arch_pfn = 0x400000000 [ 0.000000] e820: last_pfn = 0x100000 max_arch_pfn = 0x400000000 [ 0.000000] init_memory_mapping: [mem 0x00000000-0xffffffff] [ 0.000000] init_memory_mapping: [mem 0x100000000-0x138ffffff] [ 0.000000] NUMA turned off [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000138ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x138ffffff] [ 0.000000] NODE_DATA [mem 0x1387fc000-0x1387fffff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00010000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x138ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00010000-0x0009ffff] [ 0.000000] node 0: [mem 0x00100000-0x138ffffff] [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] No local APIC present [ 0.000000] APIC: disable apic facility [ 0.000000] APIC: switched to apic NOOP [ 0.000000] e820: cannot find a gap in the 32bit address range [ 0.000000] e820: PCI devices with unassigned 32bit BARs may break! [ 0.000000] e820: [mem 0x139100000-0x1394fffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on Xen [ 0.000000] Xen version: 4.1.1 (preserve-AD) [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff880138400000 s75712 r8192 d22592 u2097152 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1259871 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Memory: 4943980k/5128192k available (3937k kernel code, 448k absent, 183764k reserved, 1951k data, 524k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:256 16 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [hvc0] enabled [ 0.000000] installing Xen timer for CPU 0 [ 0.000000] Detected 3411.602 MHz processor. [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 6823.20 BogoMIPS (lpj=3411602) [ 0.000999] pid_max: default: 32768 minimum: 301 [ 0.000999] Security Framework initialized [ 0.001355] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.002974] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003441] Mount-cache hash table entries: 256 [ 0.003595] Initializing cgroup subsys cpuacct [ 0.003599] Initializing cgroup subsys freezer [ 0.003637] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' [ 0.003637] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8) [ 0.003643] CPU: Physical Processor ID: 0 [ 0.003645] CPU: Processor Core ID: 0 [ 0.003702] SMP alternatives: switching to UP code [ 0.011791] Freeing SMP alternatives: 12k freed [ 0.011835] Performance Events: unsupported p6 CPU model 42 no PMU driver, software events only. [ 0.011886] Brought up 1 CPUs [ 0.011998] Grant tables using version 2 layout. [ 0.012009] Grant table initialized [ 0.012034] NET: Registered protocol family 16 [ 0.012328] PCI: setting up Xen PCI frontend stub [ 0.015089] bio: create slab <bio-0> at 0 [ 0.015158] ACPI: Interpreter disabled. [ 0.015180] xen/balloon: Initialising balloon driver. [ 0.015180] xen-balloon: Initialising balloon driver. [ 0.015180] vgaarb: loaded [ 0.016126] SCSI subsystem initialized [ 0.016314] PCI: System does not support PCI [ 0.016320] PCI: System does not support PCI [ 0.016435] NetLabel: Initializing [ 0.016438] NetLabel: domain hash size = 128 [ 0.016440] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.016447] NetLabel: unlabeled traffic allowed by default [ 0.016475] Switching to clocksource xen [ 0.017434] pnp: PnP ACPI: disabled [ 0.017501] NET: Registered protocol family 2 [ 0.017864] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.019322] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.020376] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.020497] TCP: Hash tables configured (established 524288 bind 65536) [ 0.020500] TCP: reno registered [ 0.020525] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020564] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020624] NET: Registered protocol family 1 [ 0.020658] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.020662] software IO TLB [mem 0xfb632000-0xff631fff] (64MB) mapped at [ffff8800fb632000-ffff8800ff631fff] [ 0.020750] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.021378] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.023378] msgmni has been set to 9656 [ 0.023544] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.023549] io scheduler noop registered [ 0.023551] io scheduler deadline registered [ 0.023580] io scheduler cfq registered (default) [ 0.023650] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.023845] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.024082] Non-volatile memory driver v1.3 [ 0.024085] Linux agpgart interface v0.103 [ 0.024207] Event-channel device installed. [ 0.024265] [drm] Initialized drm 1.1.0 20060810 [ 0.024268] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 0.025145] brd: module loaded [ 0.025565] loop: module loaded [ 0.045646] Initialising Xen virtual ethernet driver. [ 0.198264] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.199096] i8042: No controller found [ 0.199139] mousedev: PS/2 mouse device common for all mice [ 0.259303] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 0.259353] rtc_cmos: probe of rtc_cmos failed with error -38 [ 0.259440] md: raid1 personality registered for level 1 [ 0.259542] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 0.259732] ip_tables: (C) 2000-2006 Netfilter Core Team [ 0.259747] TCP: cubic registered [ 0.259886] NET: Registered protocol family 10 [ 0.260031] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 0.260070] sit: IPv6 over IPv4 tunneling driver [ 0.260194] NET: Registered protocol family 17 [ 0.260213] Bridge firewalling registered [ 5.360075] XENBUS: Waiting for devices to initialise: 25s...20s...15s...10s...5s...0s...235s...230s...225s...220s...215s...210s...205s...200s...195s...190s...185s...180s...175s...170s...165s...160s...155s...150s...145s...140s...135s...130s...125s...120s...115s...110s...105s...100s...95s...90s...85s...80s...75s...70s...65s...60s...55s...50s...45s...40s...35s...30s...25s...20s...15s...10s...5s...0s... [ 270.360180] XENBUS: Timeout connecting to device: device/vbd/51713 (local state 3, remote state 1) [ 270.360273] md: Waiting for all devices to be available before autodetect [ 270.360277] md: If you don't use raid, use raid=noautodetect [ 270.360388] md: Autodetecting RAID arrays. [ 270.360392] md: Scanned 0 and added 0 devices. [ 270.360394] md: autorun ... [ 270.360395] md: ... autorun DONE. [ 270.360431] VFS: Cannot open root device "xvda1" or unknown-block(0,0): error -6 [ 270.360435] Please append a correct "root=" boot option; here are the available partitions: [ 270.360440] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 270.360444] Pid: 1, comm: swapper/0 Not tainted 3.5.7-gentoo #1 [ 270.360446] Call Trace: [ 270.360454] [<ffffffff813d2205>] ? panic+0xbe/0x1c5 [ 270.360459] [<ffffffff813d2358>] ? printk+0x4c/0x51 [ 270.360464] [<ffffffff815d5fb7>] ? mount_block_root+0x24f/0x26d [ 270.360469] [<ffffffff815d62b6>] ? prepare_namespace+0x168/0x192 [ 270.360474] [<ffffffff815d5ca7>] ? kernel_init+0x1b0/0x1c2 [ 270.360477] [<ffffffff815d5500>] ? loglevel+0x34/0x34 [ 270.360482] [<ffffffff813d5a64>] ? kernel_thread_helper+0x4/0x10 [ 270.360486] [<ffffffff813d4038>] ? retint_restore_args+0x5/0x6 [ 270.360490] [<ffffffff813d5a60>] ? gs_change+0x13/0x13 The config: name = "dom1" bootloader = "/usr/bin/pygrub" root = "/dev/xvda1 ro" extra = "3" # runlevel memory = 5000 disk = [ 'phy:/dev/md1,xvda1,w' ] # vif = [ 'ip=..., vifname=veth1' ] # none for now Here are some details on the Dom0 kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y # CONFIG_XEN_BLKDEV_FRONTEND is not set CONFIG_XEN_BLKDEV_BACKEND=y # CONFIG_XEN_NETDEV_FRONTEND is not set CONFIG_XEN_NETDEV_BACKEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y CONFIG_XEN_BACKEND=y CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PCIDEV_BACKEND=m CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m And the DomU kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y CONFIG_XEN_BLKDEV_FRONTEND=y CONFIG_XEN_NETDEV_FRONTEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y # CONFIG_XEN_BACKEND is not set CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m Any ideas what I'm doing wrong here? Thanks a lot!

  Read the article

• Failover Cluster Quorum Failing

  - by oruchreis

  Hi, I have two nodes which boots from iscsi to implement windows 2008 cluster. And I'm using disk majority option as quorum over iscsi. But when the quorum's iscsi connection failed(May be san server reset), the failover cluster is failed too. If I reset one of the nodes, it can open, but its system disk goes offline. I cant change its status as online, because it says that its reserved by failover cluster(disk is on iscsi, beacuse iscsi boot). And this disk works as readonly. Anything on it cant be deleted or written. So, I cant rejoin the node to the cluster again. I have to reinstall windows. So, what I'm asking is, how can I implement more quorum backup? I mean, can I use both disk majority and file share majority at same time? AFAIK, every nodes also keep the quorum's copy too. But I don't know sometimes san servers goes offline. And quorum's iscsi connection and nodes' iscsi connections get lost. So, nor the quorum that is kept in the nodes neither the quorum iscsi disk is not enough to start the cluster again. I want to use both disk majority and file share majority at the same time. Can I do this? Have you any other suggestion? Regards.

  Read the article

• Could not find codec parameters in ffmpeg in Windows

  - by Grienders

  While trying to convert wmv to animated gif using ffmpeg in Windows 7, I ran into an issue. Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:\>ffmpeg -i test.wmv test.gif ffmpeg version N-39877-g4fa706a Copyright (c) 2000-2012 the FFmpeg developers built on Apr 16 2012 14:57:12 with gcc 4.6.3 configuration: --enable-gpl --enable-version3 --disable-w32threads --enable-ru ntime-cpudetect --enable-avisynth --enable-bzlib --enable-frei0r --enable-libass --enable-libcelt --enable-libopencore-amrnb --enable-libopencore-amrwb --enable -libfreetype --enable-libgsm --enable-libmp3lame --enable-libnut --enable-libope njpeg --enable-librtmp --enable-libschroedinger --enable-libspeex --enable-libth eora --enable-libutvideo --enable-libvo-aacenc --enable-libvo-amrwbenc --enable- libvorbis --enable-libvpx --enable-libx264 --enable-libxavs --enable-libxvid --e nable-zlib libavutil 51. 46.100 / 51. 46.100 libavcodec 54. 14.101 / 54. 14.101 libavformat 54. 3.100 / 54. 3.100 libavdevice 53. 4.100 / 53. 4.100 libavfilter 2. 70.100 / 2. 70.100 libswscale 2. 1.100 / 2. 1.100 libswresample 0. 11.100 / 0. 11.100 libpostproc 52. 0.100 / 52. 0.100 [asf @ 0000000001f3ead0] Could not find codec parameters (Video: none (MTS2 / 0x 3253544D), 800x400, 30000 kb/s) test.wmv: could not find codec parameters What does this mean and how can I solve it?

  Read the article

• Regarding partitions for dual-booting Ubuntu with pre-existing Windows 7

  - by Shasteriskt

  I have zero actual experience with configuring disk partitions and the stuff I have read for the past few hours have been confusing me a bit, so please bear with me. First of all, I'd like to explain what I'm setting to achieve: Windows 7 with: C:\ Windows 7 (pre-existing installation) D:\ Data (Already exists and has files already) Ubuntu 11 - Does not exist yet, but I already have a LiveCD in hand. \root directory for Ubuntu \home on its own partition I plan \swap on its own partition with around 8GB Here is the current situation: I have a single 500 GB hard-disk with Windows 7 x64 installed, and the current partition schemes is as follows: System Reserved: 100 MB (Primary, Active) C: 100 GB - Where Windows 7 is installed (Primary) D: 365 GB - Where my files are located, LOTS of free space (Primary) Now, I would like to shrink my D: drive and create around 40 GB of unallocated disk space for the Ubuntu installation, but here what's confusing me a bit: I'm thinking I would create an extended partition and subdivide it into 3 logical partitions for the Ubuntu setup I had in mind. (If you think my setup is a bad idea, please let me know & why. I also hope you can suggest a better one...) I am aware that I can only have up to 4 primary partitions, or 3 primary partitions with 1 extended parition max. Now, does the System Recovery portion count as one primary partition? I'm really new to these things and it is totally unclear to me. In shrinking my D: drive using Windows 7's Disk Management tool, I would get an unallocated free space which I don't know how to make an extended partition from. It seems like I can only create a primary partition from it, not an extended one. How do I go about it? (I'd also like to note, if it is of any importance, that I am trying to avoid using the option to install Ubuntu alongside Windows, and much rather prefer using the custom install where I can specify which drives I wish to use and stuff. Somehow I feel its safer that way.)

  Read the article

• How to recover my invisible HD again?

  - by pattulus

  I made this several times now, but this time something bad happened. What I did: I installed Windows 7 at a 32GB partition on my slot 2 HD in my MacPro. Windows 7 made a 105MB partition… I knew this before, but what I didn’t know was that this partition is now on my slot 4 HD. My home folder, my private videos and some other stuff are on this 1TB drive. What I found out so far: I’m currently logged in as another admin since my OS partition as well as the two other HD's aren't harmed. Disk Utility: … only shows the 105MB NTSF partition on this 1TB volume. It isn’t showing my old 1TB partition/ex-HD named "storehouse". Only the partition tab is telling me that there now is a 1TB empty free unpartitioned space. Data Rescue II: … is showing the Volume as it used to be with it's old Name "storehouse". A quick scan and a thorough scan both were done in 1 second which leds me to the conclusion that there's isn’t something deleted at all (» hope!). Data Rescue doesn’t even mention the damn "system reserved" partition. Drive Genius: … also shows the old partition and doesn’t mention the new one. But looking at the info it tells me under "content": FDisk_partition_scheme (instead of Apple_partition_scheme). Well D'oh…. Tech Tools: … doesn’t show the volume, otherwise I'd might have been tempted to press rebuild/repair. What to do next?? I think the best approach is to buy another 1TB HD and let Disk Warrior Clone my old one to it… just to be on the safe side. But what is the best thing to do after this… ???

  Read the article

• ERROR: Not enough space?

  - by dsmoljanovic

  Now this is a very unspecific question. I'm trying to figure out what this message would mean. Here is the story behind it: I'm installing Oracle enterprise manager cloud control (12c r3) on Solaris 10 (5/09). Installer opens up, i enter all needed information and at the last step click Install. It immediately crashes with only "ERROR: Not enough space" written in log and console and nothing else. Now, this could be java error or Solaris error? I'm thinking it's happening either when it starts to copy files or when it tries to launch a process that would do that. What space is it referring to? disk (have ehough), swap (also), memory (yep)... Any ideas are helpful. Edit: i found this exception in the oraInventory logs: oracle.sysman.oii.oiic.OiicInstallAPIException: Not enough space at oracle.sysman.oii.oiic.OiicAPIInstaller.initInstallSession(OiicAPIInstaller.java:2165) at oracle.sysman.oii.oiic.OiicAPIInstaller.initOUIAPISession(OiicAPIInstaller.java:790) at oracle.sysman.install.oneclick.EMGCOUIInstaller.prepareForInstall(EMGCOUIInstaller.java:676) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext$1.run(EMGCSummaryDlgonNext.java:243) at java.lang.Thread.run(Thread.java:662) at oracle.sysman.install.oneclick.EMGCSummaryDlgonNext.actionsOnClickofNext(EMGCSummaryDlgonNext.java:1067) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at oracle.sysman.install.oneclick.EMGCUtil.performonClickOfNextForClass(EMGCUtil.java:399) at oracle.sysman.install.oneclick.EMGCUtil.performPageLevelValidationsForSilentInstall(EMGCUtil.java:367) at oracle.sysman.install.oneclick.EMGCInstaller.prepareForSilentInstall(EMGCInstaller.java:1459) at oracle.sysman.install.oneclick.EMGCInstaller.main(EMGCInstaller.java:1553) disk status: bash-3.00$ df -h /tmp Filesystem size used avail capacity Mounted on swap 8.1G 2.7G 5.4G 33% /tmp bash-3.00$ df -h /u01 Filesystem size used avail capacity Mounted on / 275G 28G 244G 11% / swap: root@gs12emcc # swap -s total: 18306040k bytes allocated + 3837808k reserved = 22143848k used, 5712664k available

  Read the article

• How do you recreate the System Recovery environment in Windows 7?

  - by Howiecamp

  I'm running Windows 7 Home Premium RTM (64-bit) and I want to take advantage of the system recovery tools (eg the Command Prompt) without using the Windows 7 DVD. My understanding is that this environment (WinRE) should be installed to your HDD by default as part of the Windows 7 installation. However, when I hit F8 on boot and select "Repair", I get: Windows failed to start. A recent hardware or software change might be the cause. To fix the problem... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. The "Info" line seems like the smoking gun. My next step was to boot from the Windows 7 DVD, and choose "Repair". It indicated my Recovery Environment wasn't on the Windows 7 boot menu (perfect) and offered to fix it. I said yes and rebooted, however same issue as above. In addition, when I booted in to Windows 7 and I looked at the boot menu options, the recovery/repair option was not there. Only my Windows installation. Finally, I ran the Disk Management tool (diskmgmt.msc) and took a look at the contents of my "System Reserved" partition (which was set to "Active" as normal). It's unclear to me what the contents should look like, however it is my understanding that the WinRE environment gets installed to this partition. (As part of the above troubleshooting I followed http://superuser.com/questions/25728/how-to-fix-windows-7-boot-process which lead to http://www.sevenforums.com/tutorials/668-system-recovery-options.html).

  Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >