Search Results

Search found 9015 results on 361 pages for 'wireless range'.

Page 27/361 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

  • wireless blocked after installing ubuntu 12.04

    - by Cornelia Frank
    I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

    Read the article

  • Ubuntu 12.04 no network connection

    - by user115711
    I own a HP probook 4530s. I installed ubuntu 12.04 along side my windows 7 professional OS. While in window 7 everything works properly in terms of wire and wireless connection. On Ubuntu 12.04 my wired connection doesn't work at all and wireless connection works only when I check off enable wireless then recheck enable wireless. When I recheck enable wireless, the wireless connection only works for about 30 seconds then it goes offline again.

    Read the article

  • Showing range on hexagonal grid

    - by user23673
    Here is the situation. I have hexagonal board,and a unit on it,with speed or move value 4.Diffrent terrain has a diffrent cost.When i click on the unit,game should show me a move range. My solution was to check each hex in range of 4,with A* pathfinding,and if path cost was less than 4 then this hex was in range.Finally game nicely show me range of that unit. My question is: Is there other solution to search for range on hex grids or square grid,because even if i am really proud of what i did in my solution,i think,it is a little to exaggerated?:)) What make me ask this question?I noticed that when unit speed is 4 or 6 or even 8,time to computing range for my computer was really good,but when speed was 10 and more i noticed that i needed to wait few second to compute.Well in real games i rather dont see something like this and my A* pathfinding is rather well optimized,so im thinking that my solution is wrong. Thanks for any replies.

    Read the article

  • networking with ssh thru wireless

    - by nkvnkv
    I am using Ubuntu 12.04 64bit on my desktop and my laptop. Have install openssh client and server on both of them. My desktop is connected to ADSL2+ Router TD-8840 with wired connection and has 192.168.1.1 IP address. My laptop is connected to 150Mbps Wireless N Router TL-WR741ND with wireless connection and has 192.168.0.1 IP address. ADSL2+ Router TD-8840 and 150Mbps Wireless N Router TL-WR741ND are connected with a wired cable by useing blue port for on wlan on TL-WR741ND. ifconfig from desktop desktop:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1d:92:37:1f:3d inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21d:92ff:fe37:1f3d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:57508 errors:0 dropped:0 overruns:0 frame:0 TX packets:44508 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:51547633 (51.5 MB) TX bytes:6371374 (6.3 MB) Interrupt:43 Base address:0x6000 eth1 Link encap:Ethernet HWaddr 00:23:cd:b1:ff:e4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:22 Base address:0x8400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:109 errors:0 dropped:0 overruns:0 frame:0 TX packets:109 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:12044 (12.0 KB) TX bytes:12044 (12.0 KB) ifconfig from laptop laptop:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:a0:d1:65:2a:42 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31244 (31.2 KB) TX bytes:31244 (31.2 KB) wlan0 Link encap:Ethernet HWaddr 00:19:d2:1b:19:81 inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::219:d2ff:fe1b:1981/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1590 errors:0 dropped:0 overruns:0 frame:0 TX packets:1276 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:874763 (874.7 KB) TX bytes:315401 (315.4 KB) I can connect to desktop from laptop via ssh with no problem, internet connection on laptop and desktop is working fine, but when I want to connect to laptop from desktop via ssh in terminal I type ssh [email protected] and get ssh: connect to host 192.168.0.101 port 22: Connection timed out If anyone is able to point out whats wrong?

    Read the article

  • Problems with wireless file copy - hangs during copy

    - by Eran Kampf
    I have this problem on my home network where when I try to copy files via wireless connection, at some point the copy fails and the machine doing the copy loses connection to the network. I'm pretty much lost as to figuring out the source for the problem... Some more details that might help: It's not OS related. I have Windows 7 machines and Leopard machines and this occurs on both I'm using a 3com OfficeConnect router Wired transfer works fine Other programs that require heavy wireless traffic work just fine:streaming large HD movies, Xbox Live! ... I'm lost as to how to even begin trying to diagnose the problem so any tips are welcome...

    Read the article

  • Wireless network not working Linux Mint

    - by zharvey
    I have a home LAN that I am confident is working properly (I have a Windows 7 and an Ubuntu Desktop machine that both see the router and a working Internet connection). I just installed Linux Mint (Maya) on a new machine and although I can connect to the Internet via a wired (ethernet) connection, it does not see my wireless network. In fact, as you can see in the screenshot below, it doesn't even look like it has the drivers to be able to detect a wireless network... I have ran update manager and made sure that I am up-to-date with everything and have restarted. Any ideas here?!?

    Read the article

  • USB ports causing Wireless and Mobile Phone tethering drop out

    - by chrolli
    I have a problem with my USB ports and I can't seem to pinpoint the problem. I'm hoping that I can get some idea as to how to troubleshoot my problem. Problem description: I recently bought a USB Wireless Adapter in order to connect my Desktop PC to the WLAN. The dongle keeps dropping off connection regularly on average once a minute. And the connection is slow. What I've tried: I installed a network scanner to determine signal strength. The PC/adapter combo is getting about 70% signal strength. I have a laptop that has an internal Wireless adapter. I moved the laptop near the location of the PC. The signal strength was above 90%. I installed the USB adapter on the laptop. I placed the laptop near the location of the PC. The signal strength was above 80%. And there is no drop out issue. I've isolated the problem to be on the PC. I used internet tethering on my mobile phone in order to test the USB ports. I get the same problem, themobile phone keeps dropping in and out. I plugged the adapter and phone on all USB ports, and it is still dropping out on all ports. I've isolated the problem to be the Motherboard, USB hub. I updated the BIOS, and USB driver. Still dropping out. I noticed that when I used the mobile phone tethering method, the phone (iphone 5) is guarenteed to drop out and does not appear to charge if I jiggle the the 8-pin connector on the base of the phone. If I push the pin tightly on the phone, the phone starts charging, as soon as I let go, it stops and drops out from the PC. This is strange because this doesn't happen when it is plugged to the powerboard. Which means that the 8 pin connector is fine. I'm not sure what the problem is. I assume that it is to do with the USB ports not supplying enough power which in turn causes the devices to intermittently drop out. The reason I say this is because the USB cable works fine when plugged into a powerboard with enough power supplied to the phone. Only when it is plugged into the USB port on the PC, does it drop out. My motherboard is Asus P8z68-v le. My Wireless adapter is the D-link DWA131. I can't seem to find any settings in the BIOS to increase the south bridge voltage so as to supply more power to the USB ports. Although this problem only occurs when I'm trying to hook up to a device supplying internet connection. My USB HDD, Flash drives, and Mouse and Key are working fine! Any suggestions please?

    Read the article

  • Aruba Wireless Controller 200 and AP70 manual

    - by techie
    I have an Aruba wireless system that is currently in use but there is no documentation from the previous person in charge. I have no manuals or login information for the wireless controllers and APs. I checked the Aruba website and you need to register to access the support information but registration isn't instant and takes several days. I've waited for quite a while now and have tried googling and checking the Aruba forums but have found no indication of a manual. What I really need is the ability to reset the controller and APs so I can access the device with the default username and password. There is no reset button on this device so I have no idea how you go about resetting the controller and APs. Hm it seems I can't create a new tag as a new user. If possible can someone add an "Aruba" tag?

    Read the article

  • Using a Netgear WGR614v9 to extend wireless signal from Netgear DG934GT

    - by moorcroft
    I'm wondering if someone could please provide me the steps for extending/repeating my wirless signal so that I can have greater wireless range throughout my house. I have 2 wirless Netgear routers, a DG934GT ADSL router (base unit) and WGR614v9 cable router (repeater). I've flashed both routers with the latest firmware and have turned on the wireless repeating function in the WGR614v9 but I can't get internet access when connected to the repeater, I can only get it when connected to the base unit. Can this be achieved by running an ethernet cable between the two routers as thus far I've only tried to get them to contact each other wirelessly. Any help would be appreciated

    Read the article

  • What's the point of Netgear's WNHDB3004 "3DHD WIRELESS HOME THEATER NETWORKING KIT"

    - by badp
    Here's a crude representation of what I've got at home: floor 2 INTERNETS ---- MODEM/ROUTER ---- MY COMPUTER | floor 1 WIFI REPEATER ---- stuff | floor 0 more stuff TELEVISION Now, as part of our sat tv subscription we can get an additional service if we connect our decoder (located by TELEVISION obviously) to the internet. What they suggest is buying a Netgear 3DHD WIRELESS HOME THEATER NETWORKING KIT holy shit isn't my bullshit-o-meter flying high right now from the general buzzwordyness of this thing. What does this thing actually do that our existing wireless-enabled routers don't do? What's the point of having a third wifi router in the same house, this time only for one television? If I do decide to plunge €99 for this, should I connect it to the wifi repeater (which does not provide AAA quality internet, at least for all gaming purposes) or to my modem/router (risking issues with low signal?).

    Read the article

  • Wireless card not found on Ubuntu

    - by Idealflip
    Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

    Read the article

  • Internet wireless connected with limited access, windows vista

    - by r0ca
    I had some malware in my computer so I did a bit of manual work to remove it including resetting TCP/IP. Now the malware is gone. I can see my home wireless network and I can get connected to it but when connected I get the Internet wireless connected with limited access message. When I go to the IE I cannot browse. When I tried to ping 192.168.1.1 I got an Error Code 1231 Unconnected Network Problem. I have deactivated my Windows firewall as I thought it could be hyperactive security. Still no luck. I have Norton but it is not active, I have also Avast and AVG installed but they are not active. Any ideas?

    Read the article

  • Aruba Wireless Controller 200 and AP70 manual

    - by techie
    I have an Aruba wireless system that is currently in use but there is no documentation from the previous person in charge. I have no manuals or login information for the wireless controllers and APs. I checked the Aruba website and you need to register to access the support information but registration isn't instant and takes several days. I've waited for quite a while now and have tried googling and checking the Aruba forums but have found no indication of a manual. What I really need is the ability to reset the controller and APs so I can access the device with the default username and password. There is no reset button on this device so I have no idea how you go about resetting the controller and APs. Hm it seems I can't create a new tag as a new user. If possible can someone add an "Aruba" tag?

    Read the article

  • unable to sniff traffic despite network interface being in monitor or promiscuous mode

    - by user65126
    I'm trying to sniff out my network's wireless traffic but am having issues. I'm able to put the card in monitor mode, but am unable to see any traffic except broadcasts, multicasts and probe/beacon frames. I have two network interfaces on this laptop. One is connected normally to 'linksys' and the other is in monitor mode. The interface in monitor mode is on the right channel. I'm not associated with the access point because, as I understand, I don't need to if using monitor mode (vs promiscuous). When I try to ping the router ip, I'm not seeing that traffic show up in wireshark. Here's my ifconfig settings: daniel@seasonBlack:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:29:9e:b2:89 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8518 (8.5 KB) TX bytes:8518 (8.5 KB) wlan0 Link encap:Ethernet HWaddr 00:21:00:34:f7:f4 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:ff:fe34:f7f4/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:9758 errors:0 dropped:0 overruns:0 frame:0 TX packets:4869 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3291516 (3.2 MB) TX bytes:677386 (677.3 KB) wlan1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-33-34-00-00-00-00-00-00-00-00 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:1500 Metric:1 RX packets:112754 errors:0 dropped:0 overruns:0 frame:0 TX packets:101 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18569124 (18.5 MB) TX bytes:12874 (12.8 KB) wmaster0 Link encap:UNSPEC HWaddr 00-21-00-34-F7-F4-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Here's my iwconfig settings: daniel@seasonBlack:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:F8:D6:17:34 Bit Rate=54 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=68/70 Signal level=-42 dBm Noise level=-69 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wmaster1 no wireless extensions. wlan1 IEEE 802.11bg Mode:Monitor Frequency:2.437 GHz Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Here's how I know I'm on the right channel: daniel@seasonBlack:~$ iwlist channel lo no frequency information. eth0 no frequency information. wmaster0 no frequency information. wlan0 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6) wmaster1 no frequency information. wlan1 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6)

    Read the article

  • Cannot remove wireless network profile even though admin account is used

    - by David Karlsson
    On my windows computer which is connected to a company domain. I have problems with the wireless networking. First of all the computer fails to connect. Second of all I cannot remove the network from the list of wireless profiles. The properties window simply claims that "This network is administered by the Administartor Account". I am currently logged in as the local administrator. I have also tried creating a new admin account and still get the same problem when trying to remove the network. My computer has only the microsoft security essentials antivirus and some VMWare+virtual box connections that I can figure might interfere, but disabling realtime protection has not helped me on this. I also cannot delete the virtual network adapters from the control panel / network adapters...

    Read the article

  • Wireless Keyboard Intermittent Failure to Type and Added Characters

    - by Kashif
    My keyboard has been acting up from time to time. It's wireless so this may be a wireless issue. What happens is I will be typing and then all of a sudden it seems to stop responding. If I type out this sentence it may show up like so If I ttennnnnnnnn it may ssssssp so While typing that sentence I may have to mash on a key repeatedly to get it to type. The resulting strings of letters seem to be coming as if the keyboard buffer cannot keep up. It's so weird. If I take the USB tranceiver and yank it out then plug it back in, Voila! Problem solved. I did the battery check so that's not a problem. Any suggestions? My keyboard is the Logitech MX3200

    Read the article

  • Can't connect to wireless-n in dual mode.

    - by Tyllyn
    I recently purchased a Acer Aspire Revo AR3610-U9022. This little nettop uses a Atheros AR5B91 Wireless Network Adapter. I also have a Netgear RangeMax NEXT Wireless Route (model WNDR3300). I have been using this router in dual mode (11G and 11N) on my normal desktop without a problem (Mode: Up to 270Mbps at 5GHz & 54Mbps at 2.4 GHz), but doing this, my Revo won't detect the 11N network as being around... my desktop still does, but the Revo, nope... just the 11G. However, when I switch my router over to just "Up to 270Mbps at 2.4GHz", it kills the 11G entirely, but the Revo recognizes the 11N network. I'm a programmer by trade, and this hardware-y stuff confuses me more than it should. Is there any way that I could set this stuff up so my Revo can connect to the 11N part of my router, but keep the 11G around? :) Thanks!

    Read the article

  • Cheapest Embedded System with Wireless Connectivity?

    - by geeko
    Problem: I'm trying to capture some information coming from keyboard, mouse and barcode reader connected to some PC via PS/2, USB and/or RS-232, before information get to PC and send it over the Internet to some central server. I'm thinking to do so by using some kind of hardware interface (middleware, if you like) between PC and input devices. I thought this interface can be embedded PC, PDA or simply some mobile phone with wireless connectivity. PS/2 and RS-232 could be converted to USB using some USB convector/hub that connects to one of these interface systems. Then some special API programming take place to communicate between PC, input devices and wireless server, in the form of application running on the interface system. What's the cheapest solution that can achieve this? Or possibly any other solution?

    Read the article

  • Migrate wireless settings from xp to windows 7

    - by Tgr
    I'm trying to migrate the settings of my old machine (Win XP Professional) to the new one (Win 7 Professional) and I would like to keep my saved passwords for various wireless networks. How can I export them from XP and import in Win7? A few things that are mentioned a lot in chat groups but don't work: netsh can export/import wlan profiles on Vista/Win7, but not on XP; the Wireless Network Setup Wizard can only export settings for networks created by me; the best method I found was via http://www.nirsoft.net/utils/wireless_wep_key_faq.html which can list hex keys, but cannot load them nor save them in a useful format; I would rather not copy them one-by-one by hand.

    Read the article

  • Installing a Wl-138g wireless NIC on ubuntu server

    - by Narcolapser
    So I have this little server that I've been working on as a hobby. But due to changes in living arrangements I have move and it won't have access to a wired lan. So I need to install a wireless adapter i had sitting around. But most tutorials I have run across are either out dated, or about ubuntu desktop and talk about things using a GUI. So my question is firstly is there a utility for identifying and downloading drivers for new hardware. that would save my having this problem in the future. If not, how do i go about installing said wireless NIC? ~N

    Read the article

  • Use dns suffixes only on certain wireless networks?

    - by eidylon
    Hello all, quick question. I'm a software guy and networking is all black magic to me! I have a laptop which I use at home and at the office. In order to be able to more easily reference our servers at work, I have our domain name in the DNS suffixes on my TCP/IP settings on my wireless connection. This all works beautifully and I can reference our servers simply by name only. Now the problem... When I go home, it still has those suffixes in there, and I cannot access other servers because it appends the DNS suffixes to the server names. Is there a way I can set up DNS suffixes so that they are only applied when connected to a certain wireless network (I'm thinking by SSID).

    Read the article

  • Suggest Wireless AP

    - by sunny
    I'm doing a data and voice install for a client in the hotel industry. I'm done with voice and am looking for my options to provide a Wireless AP. The building's dimensions are 100ft X 50ft. There are a ton of options out there which have left me confused now. Please help me decide. I am not clear as to how I should ensure that the Wireless Network is visible throughout the premises. Personally I would love to setup a WDS on 3-4 linksys wrt54gl routers using OpenWRT. Is this advisable? If not please recommend some other AP's. If a more expensive appliance is absolutely necessary, then please suggest something that can be powered using IEEE 802.3af PoE. Thanks

    Read the article

  • Wireless card not found on Ubuntu

    - by idealflip
    Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

    Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >