Search Results

Search found 24117 results on 965 pages for 'write through'.

Page 27/965 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

• Motherboard jumper setting: BIOS flash write protection.

  - by Wesley

  I have an ECS P4M800PRO-M478 motherboard and I'm just setting up the jumpers right now, of which there are only two sets. One is the CLR_CMOS jumper, which is set to Normal, of course. However, there is another set called BIOS_WP which controls whether BIOS flash writing is protected or unprotected. Which setting should I have it set at and would this affect any BIOS flashes in the future?

  Read the article

• RAID Read/Write Speed Gradually Slows

  - by Nalandial

  This is actually a server at home, but I felt it was sufficiently complicated as to not have it on SuperUser and could easily apply to a professional situation. I have a file server running Debian (Lenny 5.0.4), and it has an XFS LVM on top of a RAID 5 with the OS drive separate from the RAID. It's also running apache, samba, and postgresql. Side note: before anyone asks, I'm using RAID5 because I get more bang for the buck on raw drive space, and still have some fault tolerance. When the box is started (via shutdown or reboot) reading/writing to it's samba share maxes out the gigabit network connection. Over time, this slowly degrades eventually becoming < 10MB/s; however, when rebooted the speed returns to maxing out the connection. Why is this happening, and is there a way to 'clear' out whatever's causing it without taking the server down? Thanks in advance!

  Read the article

• Write permissions LAMP (Debian Lenny)

  - by letseatfood

  I am working on a PHP script that transfers files using FTP functions. It has always worked on my production server (which is a hosting service). The development server I have just setup (I am a novice to servers) is Debian Lenny with Apache2, PHP5, and MySQL5. The file transfer works correctly, but once the file has been written to the server, it has permissions of 600. This makes it impossible for me to view the file (JPEG) in the web browser, as permission is denied. I have scoured the internet and even broken my server installation and reinstalled it trying to figure this out (which has been fun, nonetheless!). I know it is unwise to set 777 permissions on public accessible files, but even that will not solve the problem. The only thing that works is if I chmod 777 thefile.jpg after it has been transferred, which is not a working solution. I tried changing the owner of my site files to www-data per this post, but that also does not work. My user is mike, and it still does not work whether the owner of the files is mike or root. Would somebody point me in the right direction? Thanks! And, of course, let me know if I can clarify anything.

  Read the article

• Testing for disk write

  - by Montecristo

  I'm writing an application for storing lots of images (size <5MB) on an ext3 filesystem, this is what I have for now. After some searching here on serverfault I have decided for a structure of directories like this: 000/000/000000001.jpg ... 236/519/236519107.jpg This structure will allow me to save up to 1'000'000'000 images as I'll store a max of 1'000 images in each leaf. I've created it, from a theoretical point of view seems ok to me (though I've no experience on this), but I want to find out what will happen when there will be directories full of files in there. A question about creating this structure: is it better to create it all in one go (takes approx 50 minutes on my pc) or should I create directories as they are needed? From a developer point of view I think the first option is better (no extra waiting time for the user), but from a sysadmin point of view, is this ok? I've thought I could do as if the filesystem is already under the running application, I'll make a script that will save images as fast as it can, monitoring things as follows: how much time does it take for an image to be saved when there is no or little space used? how does this change when the space starts to be used up? how much time does it take for an image to be read from a random leaf? Does this change a lot when there are lots of files? Does launching this command sync; echo 3 | sudo tee /proc/sys/vm/drop_caches has any sense at all? Is this the only thing I have to do to have a clean start if I want to start over again with my tests? Do you have any suggestions or corrections?

  Read the article

• Why can't they write viruses for Mac computers?

  - by Mehper C. Palavuzlar

  They always say that one of the most important advantages of Macs is that no viruses are written/coded for them. What is the reason behind it? Is it so difficult or impossible to code a virus on Mac?

  Read the article

• What file types can OpenOffice read or write

  - by Nifle

  Could anyone give me a current list of file types OpenOffice supports. Both what it can open and what it can export to?

  Read the article

• Write permissions on uploaded files - PHP & Linux

  - by letseatfood

  I am working on a PHP script that transfers files using FTP functions. It has always worked on my production server (which is a hosting service). The development server I have just setup (I am a novice to servers) is Debian Lenny with Apache2, PHP5, and MySQL5. The file transfer works correctly, but once the file has been written to the server, it has permissions of 600. This makes it impossible for me to view the file (JPEG) in the web browser, as permission is denied. I have scoured the internet and even broken my server installation and reinstalled it trying to figure this out (which has been fun, nonetheless!). I know it is unwise to set 777 permissions on public accessible files, but even that will not solve the problem. The only thing that works is if I chmod 777 thefile.jpg after it has been transferred, which is not a working solution. I tried changing the owner of my site files to www-data per this post, but that also does not work. My user is mike, and it still does not work whether the owner of the files is mike or root. Would somebody point me in the right direction? Thanks! And, of course, let me know if I can clarify anything.

  Read the article

• file corruption on read/write 2.6.32-22-server (happens across many kernels)

  - by Jonathan

  Hi Guys, I'm having an issue where after the server has been up for a period of time (~week/few days) the server will start reading corrupt data. For instance when I run a sha1sum of a file after a fresh boot it remains the same. However after a while I will start to get segfaults and from then on whenever I read this file I get a different sha1sum. I've checked S.M.A.R.T with long tests and I've run an extended memtest86+(12 passes) My lspci is as follows: 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3300 Graphics 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller 02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. Device 3403 I could really use some help on this, do you have any idea what could cause this? It's really frustrating me as it seems to trigger entirely randomly and will not go away until I reboot. I'm also use KVM for virtualization as well as MD for software RAID on this server and the processor is a Phenom II X4 965. I don't believe it's the software raid however as this affects files also hosted on non-raid partitions so I don't know.

  Read the article

• Granting read-write rights to my web application on VPS

  - by davykiash

  Am currently testing a bulk CSV import functionality web application and I came across a error The given destination is not writeable My application is zend based and uses the MVC structure application --uploads library --Zend public --index.php What Ubuntu command do I exectute to safely grant the necessary rights to my uploads folder in my web application?

  Read the article

• Why is group write permission ignored in Ubuntu?

  - by NorthPole

  I want my user to have full access to the local Apache root folder, and I also want the Apache user to have full access to the same folder. What I did was create a new group called DevGroup and I added my user and www-data there. Also I changed the permissions to 770 to allow full group access. But now it won't allow me or the Apache user any kind of access to the folder. Here is what I get with ls: drwxrwx--- 12 root DevGroup 4096 Sep 27 17:34 testFolder Which seems perfect but when I try as a user to access the file I get this: var/www$ ls testFolder/ ls: cannot open directory testFolder/: Permission denied Also when I try to access a page in the folder from a browser: [Thu Sep 27 17:47:16 2012] [error] [client 127.0.0.1] PHP Fatal error: Unknown: Failed opening required '/var/www/testFolder/foo.php' (include_path='.:/usr/share/php:/usr/share/pear') in Unknown on line 0 What's the problem and how can I fix it?

  Read the article

• I am trying to write an htaccess file performs authentication and redirects authenticated users to a

  - by racl101

  This is what I have so far but I can't get the RewriteCond and RewriteRule properly. RewriteEngine On RewriteCond %{LA-U:REMOTE_USER} (\d{3})$ RewriteRule !^%1 http://subdomain.mydomain.com/%1 [R,L]. AuthName "My Domain Protected Area" AuthType Basic AuthUserFile /path/to/my/.htpasswd Require valid-user This is what I mean the ReWriteCond and RewriteRule to say: "If the REMOTE_USER has a username ending in 3 digits then capture the three digits that match and for whatever url they are trying to access if it does not start with the 3 digits captured then redirect them to the sub directory with the name equal to those captured three digits." In other words, if a user named 'johnny202' is authenticated then if he's requesting any directory other than http://subdomain.mydomain.com/202/ then he should be redirected to http://subdomain.mydomain.com/202/ The only thing I can think of that is wrong is the first instance of '%1'.

  Read the article

• Write permissions on uploaded files - Linux, Apache, PHP

  - by letseatfood

  I am working on a PHP script that transfers files using FTP functions. It has always worked on my production server (which is a hosting service). The development server I have just setup (I am a novice to servers) is Debian Lenny with Apache2, PHP5, and MySQL5. The file transfer works correctly, but once the file has been written to the server, it has permissions of 600. This makes it impossible for me to view the file (JPEG) in the web browser, as permission is denied. I have scoured the internet and even broken my server installation and reinstalled it trying to figure this out (which has been fun, nonetheless!). I know it is unwise to set 777 permissions on public accessible files, but even that will not solve the problem. The only thing that works is if I chmod 777 thefile.jpg after it has been transferred, which is not a working solution. I tried changing the owner of my site files to www-data per this post, but that also does not work. My user is mike, and it still does not work whether the owner of the files is mike or root. Would somebody point me in the right direction? Thanks! And, of course, let me know if I can clarify anything.

  Read the article

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• Git push write access for deployment denied

  - by Stepchik

  I have strange issue when try git push. Git clone and commit works fine. W access for my_project DENIED to deploy_my_project_ My gitolite.conf repo my_project R = deploy_my_project_111 RW+ = my_name I wonder why git push takes wrong user (deploy_project_111) with read access. This error is float. Twice i had to change rsa key(rsa keys is unchangeble) and restart computer. May be my computer do something wrong.

  Read the article

• User http does not have write permissions directory?

  - by dwieeb

  I have a bit of an odd set up, I think. I have groups for each domain my server hosts, and I add the user http to each domain group along with the users that should have access to the groups' domains. In my php script running from a directory 'public_html', I try creating a file: <?php $output = ""; print exec('touch test 2>&1', $output); But I get touch: cannot touch `test': Permission denied and the file is not created. But here, clearly stated, the group has all permissions on the directory: drwxrwxr-x 5 dwieeb example.com 1024 Feb 4 05:19 public_html And here are the permissions on the php file in public_html that is trying to use the exec function: -rw-rw-r-- 1 dwieeb example.com 59 Feb 4 05:19 test.php How is this possible if http is part of the example.com group (as seen from a cat on /etc/group) and the directory has full permissions for the group? ... example.com:x:1000:dwieeb,http I'm stumped. EDIT (since apparently I'm not cool enough to answer my own questions yet): Ah, I found the problem. Yes, I restarted Nginx, but the php-fpm daemon must be restarted as well when http is added to the group for my domain. On Arch Linux: rc.d restart php-fpm

  Read the article

• java -version doesn't write to stdout?

  - by Zárate

  Hi there, Either I'm doing something silly or Sun is. How come something like: java -version > version.txt Still prints out to stdout and leaves version.txt empty? I'm checking out the exit code, and it's still 0, so is not that's writing to stderr. I need this because I'm building a test-environment tool and want to check if the version of Java is adequate, I was planning to catch that version output, but now I'm stuck. I'm on OS X Leopard, Java version 1.6.0_20. Any ideas? Cheers, Juan

  Read the article

• Terminal Server/Win2K3: Users can't write to their My Documents or Temp folders

  - by Tim Sullivan

  I have a situation where a bunch of users are running our software on a Terminal Services machine on Windows 2003 Server. I've removed most permissions from the User group, but made sure they all have the appropriate permissions for their own application folders, as well as for their Documents and Settings folder. For some reason, even though everything seems to be set up properly, users can't create or delete files from their My Documents, Temp or other D&S folders. Whatever could be going on? I thought this was going to be straightforward, but clearly it's not! :-) Thanks for any help!

  Read the article

• How to read and write Mac drives on Windows

  - by Svish

  I have some external hard drives that are Mac OS Extended (Journaled) formatted. What software can you recommend for working with those drives when under Windows? Do you have any experience with this? Would be best if the software is free, but it doesn't have to be. Hope someone can help!

  Read the article

• Removing write permission on home and public_html on Centos/Cpanel

  - by user5858

  I'm running sites on two Cpanel accounts on my VPS on WHM. I'm using DSO php handler and Apache server on my Web server. After recent intrusion attacks I've chowned to root with permission 555 on $HOME and public_html folder. I'm on VPS with Cpanel on Centos. I'm running CMS based software like Joomla Drupal etc. Will this cause any problem to my VPS installation or server side processes? Drupal, Joomla, MyBB etc will not be affected by this. Some files will not be created like error_log. At least hackers will not be able to place any malicious code within home folder or the public_html folder.

  Read the article

• Write to stdin of a running process using pipe

  - by aditya

  I am in a similar situation as in this post But I couln't get the solution provided there to work in my situation as the answer seems related to that question only. In particular, I couldnt understand what was the purpose of cat my.fifo | nc remotehost.tld 10000 In my case, I have a process running and waiting for input. how can I send input to that process using named pipes? I've tried echo 'h' > /proc/PID/fd/0 it just displays 'h' on the process' window.

  Read the article

• SAMBA and Linux ACLs -- "Permission denied" on write to share but file written nevertheless

  - by MCH

  I set up a writable share directory "/home/net/share" with acl like this: sudo mkdir -p "/home/net/share" sudo setfacl -m "u:localuser:rwx,u:remoteuser:rwx,g:users:rwx" "/home/net/share" My /etc/samba/smb.conf looks like this: [global] workgroup = w server string = server security = user load printers = no log file = /var/log/samba/%m.log max log size = 50 dns proxy = no printing = bsd printcap name = /dev/null disable spoolss = yes encrypt passwords = true invalid users = nobody root follow symlinks = yes wide links = yes [share] comment = Writable by localuser and remoteuser path = /home/net/share valid users = remoteuser read only = no public = no printable = no Locally, localuser and remoteuser have user accounts and smbpasswds and can both read, create and delete files in /home/net/share. But when I log on from a different machine (like this: sudo mount -t cifs //server/share mountpoint/ -o username=remoteuser ), I get "Permission denied" both when trying to create directories and files, oddly though, it does create files (not directories!) despite these messages! How can I get this working?

  Read the article

• Can't Read/Write the Hard disk used in NAS

  - by mgpyone

  I've lately purchased a Synology DS212j and I intended to use my two 3.5" HDs into it. One of them was in used as an external HD. Thus when I install these two unit in NAS, it asked me to formatted in order to used with its format (I think it's ext3?) . I installed the Disks and omit the formatting option. I just got another 3.5" Hard Disk now. I've installed it in the NAS. everything's fine. However, when I take out the (used) HD from the NAS and install back in the standalone casing, I found out that it can't be read from both OSX an Windows 7. I've tried with ext2sd and I only found 2GB portion of the whole 1.5 TB Hard Disk. Here's another reference from EASEUS Partition Master

  Read the article

• Heavy write to Galera cluster - table locked, cluster practically unusable

  - by Joe

  I set up Galera Cluster on 3 nodes. It works perfectly for reading data. I have done simple application to make some test on the cluster. Unfortunately I have to say that the Cluster fails totally when I try to do some writing. Maybe it can be configured differently or I do sth wrong? I have a simple stored procedure: CREATE PROCEDURE testproc(IN p_idWorker INTEGER) BEGIN DECLARE t_id INT DEFAULT -1; DECLARE t_counter INT ; UPDATE test SET idWorker = p_idWorker WHERE counter = 0 AND idWorker IS NULL limit 1; SELECT id FROM test WHERE idWorker = p_idWorker LIMIT 1 INTO t_id; SELECT ABS(MAX(counter)/MIN(counter)) FROM TEST INTO t_counter; SELECT COUNT(*) FROM test WHERE counter = 0 INTO t_counter; IF t_id >= 0 THEN UPDATE test SET counter = counter + 1 WHERE id = t_id; UPDATE test SET idWorker = NULL WHERE id = t_id; SELECT t_counter AS res; ELSE SELECT 'end' AS res; END IF; END $$ Now my simple C# application creates for example 3 MySQL clients in separate threads and each one executes the procedure every 100ms until there is no record where column 'counter' = 0. Unfortunately - after about 10 seconds sth is going bad. On servers there is process 'query_end' that never ends. After that - you cannot make update on the test table, MySQL returns: ERROR 1205 (HY000): Lock wait timeout exceeded; try restarting transaction . You cant even restart mysql. What you can do is to restart server, sometimes whole cluster. Is Galera Cluster so unreliable when you do massive concucurrent writing/updates? Hard to believe.

  Read the article

• Write stderror to a file using PowerShell

  - by Zian Choy

  How do I capture error messages from a PowerShell-launched command in a text file? I searched the Internet for a while and found that supposedly, I should be able to do something like cmd /c "big blob of text >C:\output.txt 2>c:\errors.txt" to direct the output to output.txt and the errors to errors.txt but when I try to run the command, I get the following error: cmd.exe : The filename, directory name, or volume label syntax is incorrect. At C:\Users\Zian\Desktop\Untitled1.ps1:27 char:4 + cmd <<<< /c $command + CategoryInfo : NotSpecified: (The filename, d...x is incorrect.:String) [], RemoteException + FullyQualifiedErrorId : NativeCommandError Furthermore, if I try to run the command without everything starting at "2", then the command executes correctly and output.txt catches the right output. I looked at Redirect stderr to variable in powershell but it wasn't helpful because the answer to that question suggests capturing the entire output and filtering it in memory. In my case, I am backing up every database on a computer and since the databases won't fit in my laptop's RAM, I cannot use the question's solution. I also found tantalizing suggestions about using $err = @(command goes here) but with no information on what to do other than simply inserting that line of text. I tried to utilize the search function on Serverfault with the string "@()", but it did not return any results. What can I do to get the error messages into errors.txt?

  Read the article

• group write permission ignored in ubuntu

  - by NorthPole

  Its probably my stupidy here but i'm stuck on this and would appreciate the help. I want my user to have full access to the local apache root folder, and i also want the apache to have full access to the same folder. What i did was create a new group called DevGroup and i added my username and www-data there. also i changed the permissions to 770 to allow full group access but now it wont allow me or the apache any kind of access to the folder. here is what i get with ls drwxrwx--- 12 root DevGroup 4096 Sep 27 17:34 testFolder which seems perfect but when i try as a user to access the file i get this var/www$ ls testFolder/ ls: cannot open directory testFolder/: Permission denied also when i try to access the a page in the folder from browser [Thu Sep 27 17:47:16 2012] [error] [client 127.0.0.1] PHP Fatal error: Unknown: Failed opening required '/var/www/testFolder/foo.php' (include_path='.:/usr/share/php:/usr/share/pear') in Unknown on line 0

  Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >