Search Results

Search found 59257 results on 2371 pages for 'windows identity'.

Page 270/2371 | < Previous Page | 266 267 268 269 270 271 272 273 274 275 276 277  | Next Page >

• Windows 7 - Explorer fails to load with UAC enabled

  - by mfranklin

  While running an InstallShield based installer, my Windows 7 machine became unresponsive. After forcing a reboot, I can log in to the system, but explorer does not run. I can log in as a different user without issue and when I change modify UAC to its lowest setting, I can log in as the user that was performing the install. However, if I re-enable UAC, I am unable to get explorer to run again on login. I have checked the HKCU\Software\Microsoft\Windows\CurrentVersion\Run and RunOnce, but don't see anything that isn't configured to run in the user that I can successfully log in as. I completed the installation of the software as the "good" user without issue.

  Read the article

• What's normal Taskbar behavior (windows)

  - by Erik

  I'm a fairly new user to windows, and Vista is my first version. I'm a bit confused about the taskbar -- either its behaving oddly or I'm just confused, or I've broken something. When I've got a lot of windows on screen, I thought that clicking on a window's taskbar icon would bring that window to the front. I thought it had been doing that in the past, but I'm not entirely sure. When I click it, it just flashes, a second click minimized, and a third click reopens and brings it to the front. Is this normal?

  Read the article

• Cloning Windows 2003 Server to new hard drive results in failure

  - by Level1Coder

  Scenario: Old hdd is a Seagate 320gb SATA drive New hdd is a WD 320gb SATA drive Created an exact clone and replaced old hdd with new hdd. Boot up with new hdd, it gets into Windows 2003 server environment but things look weird. Lots of system event failures in the event viewer log. System is barely unusable, critical services are all down. Boot up with old hdd, everything is fine. QUESTION: Is it possible to do a simple clone of a Windows 2003 server system? All I'm changing is the hard drive, everything else stays the same (old CPU/old mobo/etc..)

  Read the article

• Setting up a LAN connection in Windows

  - by user30780

  I'm looking to set up a LAN connection under Windows XP. What are the steps or instructions I should follow to make this work?

  Read the article

• Can't install newer NVIDIA display driver on Windows 7

  - by Mr.X

  I'm using Windows 7, and the latest version of NVIDIA display driver I can install on my computer is 275.33 (or 266.58, I can't decide now, see below). When installing newer version of the driver (e.g. 275.50 and 280.26), the installer always fails at "Installing NVIDIA Control Panel", then Windows 7 reverts to 275.33 (the newest stock version?). I tried to find installation logs but couldn't find it. I tried to completely delete (in fact I renamed) c:\progra~1\nvidia~1 folder but still couldn't install. How to resolve this problem? Any help is appreciated.

  Read the article

• Using Shell32 to extract Mimes on Windows Server 2008

  - by Léon Pelletier

  In a desktop app, I'm using Shell32 to extract Mime infos and ID3 tags. I want to do the same in ASP.Net on server side with http posted files, plus fetch some other infos, but as a Windows Server 2008, there are not several media applications installed, so I wonder if it will still retrieve a lot of informations from the files. Will it be possible to do it from server side? If yes, will it fetch several Mimes without media app installed. If not, is there some Mime pack to get some file informations without the app being installed. [EDIT] I installed VLC player and Windows Media Player on the server, which provide all MP3s / movies infos (Duration, Artist, Album, Width, Height, etc.), but I don't know if this is a good practice.

  Read the article

• Installing a fake microphone on Windows Server.

  - by Adrian

  My application, that is running on Windows Server (which is an instance on Amazon EC2) requires Skype to be able to make phone calls. The server, of course, does not have a microphone installed and I don't need it to have one, because my application changes the input source to a wav file when the call is established. However, Skype has a strict rule that a microphone must be installed for a call to be made. Thus I want to install a fake microphone that will trick Skype's configuration. So far, I was able to start and run the Windows Sound service, which enabled all of the sound settings. Any ideas are very welcome!

  Read the article

• How to make a drive partition and install Windows on it from an HP install disc

  - by Zohaib

  I bought a new HP DV6-S190SE, and I want to make multiple partitions on the hard drive. I went to HP's site and discussed with them using online chat. They said that this is not useful to make more than one partition, as when you recover your windows after some time it will erase/delete all files including new partitions, so this would not be very usefull for you. Now, if there is there any way to get rid of the existing structure and install Windows only on the C drive? First of all, how do I partition the harddrive?

  Read the article

• ssmtp for windows

  - by reox

  I have the following problem with a software that should do mail notification for a biometric entry system: the software does currently only support SMTP over port 25 without TLS/SSL. Which is bad because port 25 is blocked in our network due spam reason and our mailserver only support TLS / SSL logins. so i need a solution to connect to a localhost smtp server which just relays to my ssl host on port 587. i know there is ssmtp for linux, but i need it for windows, because the server app for this biometric stuff only runs on windows... edit: i know there is the IIS SMTP Server, but maybe something different?

  Read the article

• Windows Console .exe won't run if it's downloaded from the internet

  - by Jason Kester

  I have a nightly job on Windows Server 2003 that automatically updates itself by downloading its .exe from Amazon S3. I've noticed that when it performs the download and tries to run the newly downloaded .exe, it is immediately kicked back to the command line without actually running anything. I can verify this by sticking the new version of the code directly on the server and watching it execute successfully, then uploading it to the "update" server, running the bootstrapper then running the .exe and observing it fail to execute. I can only assume that this is due to Windows protecting me from running code from outside its trusted zone. How does a fella go about configuring it to allow code from this particular external location to execute? Thanks!

  Read the article

• Schedule task in Windows 2008

  - by user34759

  Hi i was trying to schedule one application in Windows 2008 server. and i can see that the schedeule is showing running in the task Scheduler, but nothing is happening(i mean the program that i scheduled is not working) and the schedule is not stopping also(i specificaly choose if the schedule runing more than 3 hours stop it automatically) i went through several links and im sure im scheduling it in proper way. is anybody facing this problem on Windows 2008? any resolution. Appreciate your feedback. Regards Joseph

  Read the article

• Windows Server 2008 R2 foundation VM unable to detect network adaptor

  - by user50273

  I created a Windows Server 2008 R2 foundation VM on Windows Server 2008 using Hyper-V. But I am not able to connect to internet from the VM. If I goto device manager, the network adapter branch itself is missing. I searched in google and few sites suggested I need to install the Integration Services although in one site they said Server 2008 R2 comes with integration services installed. Anyways I tried to install IntegrationServices using hyper-v but I get error dialog "error: unable to launch one of the update programs". Any suggestions on what am I supposed to do?

  Read the article

• Windows server detected error with hard disk

  - by user53864

  We have hosting Windows server 2008 R2 and I am working as admin in small company. The server is hanging and restarting as the hard disk seems to be damaged due to power fluctutaion(though having inverter) as it's showing the below error message on server reboot: Problem detected with the hard disk Press any key to continue It's Seagate 1TB SATA hard disk and it's booting after pressing enter. So it's clear that the hard disk is dying. Yes, it's in warranty but it's fact that warranty won't recover the lincesed windows server 2008 and it's data. As it's booting now, I backed up required things and I am thinking to clone the entire hard disk. The first thing it striked me is checking on the Seagate site if any tool available for cloning and I found Seagate DiskWizard but not specified it for windows server 2008. Please anybody could help me giving your best ideas for the below: Urgently, What's the best way(free of cost) for me to clone in my case with the new same sized hard disk? It's a one time lincenced and I cannot use the same key again if I reinstall the server. Will the lincense be carried with new disk if cloned? else there is a way to contact Microsoft explaining the problem occurred, to obtain new key for no charge?. I want to take measure for future. How do I keep two disks in continuous sync? mirrored & raid are the only options converting the disks to dynamic? or is there a best way I could do with no additional charge?. Any help is greatly appreciated. Thank you! EDIT:1 I started cloning the disk with CloneZilla and it was going proper showing in GUI. But after some time there is no GUI but a black screen with some codes(looks like disk location numbers) going page by page(I have attached the screenshots below captured from my phone). Do you people think it's actually cloning?. I started in the morning and it's evening now. I left the office now to let it finish what it's trying to do and I'll go & check it tomorrow. Slowly lost hope, don't know what face it's going to show tomorrow. Any ideas?

  Read the article

• Windows 2008 - Define IP Order by port or service

  - by Josh

  I have a Windows 2008 server that has three IP bound to the NIC. I can select which IP Windows SMTP listens to, but I want to also set the IP address used when mail is sent. Where would I set which outbound IP to use when sending email? Without using real IPs, here is an example what I have setup. Three IPs associated with the server: 10.0.0.1 10.0.0.2 10.0.0.3 I setup the binding on 10.0.0.2 for port 25 in the SMTP server settings, so that it is the only IP that will respond for inbound. When I look at the email header from an email sent from that server, it lists the server with an address of 10.0.0.3. I would like it to use 10.0.0.2 so that when reverse DNS is performed, it maps back correctly.

  Read the article

• Linux and Windows machines sharing a network

  - by Saif Bechan

  I have different Windows and Linux machines that share an internal private network. From within this network I can SSH to every machine etc. This internal network works great. I have my main windows machine from where I control these machines either trough SSH or virtual desktop. Is there a way for me on my main machine to see all the machines that are connected to the network. I want to be able to see all the machines and maybe browse them, share files etc. I am very new to networking of this kind so any recommendations are welcome. Should I set up this network by workgroup? I do not think Linux supports that. Or should I set up the network with domain, I never did that before.

  Read the article

• Emoticons for Windows messenger 5

  - by Ravisha

  We are using windows messenger 5 version in our company.Can some one send link to isntal more smileys/emoticons

  Read the article

• Domain redirection to port on Windows Server 2008

  - by Rauffle

  I have a Windows server running IIS. I wish to run a piece of software that hosts a web interface on a non-standard HTTP port (let's say, port 9999). I have static DNS entries on my router for two FQDNs, both of which direct to the Windows server. I wish to have requests to 'website1' to continue to go to the IIS website on port 80, but requests for 'website2' to instead go to port 9999 to be handled by the other application. How can I accomplish this? Right now I can get to the application by going to 'website1:9999' or 'website2:9999'.

  Read the article

• Installing VirtIO drivers in Windows Server 2008

  - by Stefan K.

  We are running a Windows Server 2008 system as a "guest" on a Linux-KVM virtual server (SLES11, with VirtIO support). We have trouble with the system performance and this is possibly due to not using the VirtIO drivers. I don't have much experience with neither KVM not VirtIO. Just heard it this could be the reason for our problem. Questions: The install examples I just found are describing how to install the drivers during Windows setup. Is it possible to install the VirtIO drivers later? We have running software on that system and would like to avoid reinstalling/setup of all these. I already found a page describing how to sign the drivers, which seems to be needed. A good tutorial page (step by step instructions) would be nice. Is there anything like that out there?

  Read the article

• custom windows 7 themes

  - by Ieyasu Sawada

  I found one at deviantart.com: http://browse.deviantart.com/?qh=&section=&q=adagio+theme#/d2zwu22 I like the adagio theme, except that you cannot see the content of the address bar unless you click your mouse on it. Is there any site that you know wherein I could download custom themes for windows 7. Themes that would actually modify the looks of it. Not just the colors,icons and wallpaper. Can you recommend a theme for me. A theme that would modify the navigation, close, min, max buttons in the windows explorer

  Read the article

• Issue with Windows Server backup

  - by mamu

  I have windows server 2008 r2 installed, Only service running on it is hyper-v. I am trying to take backup using windows server backup feature and it fails with following error in eventlog The backup operation that started at '?2009?-?08?-?22T18:42:14.123000000Z' has failed because the Volume Shadow Copy Service operation to create a shadow copy of the volumes being backed up failed with following error code '2155348129'. Please review the event details for a solution, and then rerun the backup operation once the issue is resolved. Above error itself is point to other event logs for more detail but i can't find anything in event logs Then i ran following command vssadmin list writers It had following out of ordinary in list Writer name: 'Microsoft Hyper-V VSS Writer' Writer Id: {66841cd4-6ded-4f4b-8f17-fd23f8ddc3de} Writer Instance Id: {d15c5f78-121c-464f-b23b-f285e919b05c} State: [8] Failed Last error: Inconsistent shadow copy How could i resolve this?

  Read the article

• Windows Services don't automatically start after reboot?

  - by James Crowley

  We've got some Windows services written in .NET. They start fine manually within the services mmc, but despite being set to Automatic, they never start when powering on (or rebooting) the machine. Update In the event log, instead of seeing "xyz started", alongside all the other services starting, I just see "The xyz service entered the stopped state." and a seperate error that says "A timeout (30000 milliseconds) was reached while waiting for a transaction response from the slsvc service.". If I manually start them, then I get a normal in the event log as expected, and all is fine - until the next Windows Update patch which forces a reboot and all the services are off again. Any ideas? I've tried setting them to Delayed Start with no apparent difference.

  Read the article

• Recover Bios HP DV9700T windows 7 64

  - by petebob796

  I downloaded the latest DV9700t bios (.59) and ran the update tool in windows 7 64. This seemed to go ok and did the usual system will shutdown in 10 seconds dialog. Updon the reboot nothing happens I get no BIOS screen or anything so I think the bios update went wrong. Which I am annoyed about I have never known a bios update to fail before and lots of people on the internet seem to have had the same problem with the same model. There is a way to recover apparently using crisdisk utility and creating a bootable usb key then holding win+b at power on, unfortunately the utility to make the disk doesn't seem to work in 64 bit versions of windows, the only type I have easy access to. Anyone know a way to create the boot disk in 64?

  Read the article

• Commands not working in Windows 7 32-bit command prompt

  - by Precious Tijesunimi

  I have an HP laptop with a Windows 7 32-bit Home Premium operating system. My command prompt doesn't run lots of commands like help, shutdown, ipconfig, ping, etc. I get a message like: 'help' is not recognized as an internal or external command, operable program or batch file. Only simple commands like cd and dir are working. I noticed that whenever I navigate to c:/windows/system32, the command works. But I need to run some important commands like java on a file that is on the desktop and not in the system32 folder. How can I fix this?

  Read the article

• Windows 2008 startup script will not run?

  - by larsks

  I am trying to get a very simple batch script to run when my Windows 2008 Server (R2) system starts up. I have added the script to the "Startup Scripts" in the local group policy by running gpedit.msc, and I see the script listed under Windows Settings/Scripts (Startup/Shutdown)/Startup when I run rsop.msc, but the script is not being executed. The "Last Executed" column in rsop is empty even after a reboot, and a file that should be created by the script is never created. At the moment, the entire contents of the script are: rem Check if this script is running. date /t > c:\temp\flag The target directory (c:\temp) exists. The script is called c:\scripts\startup.bat, and works fine if I run it by hand.

  Read the article

• Cannot install wireless lan service on windows 2012 RTM offline

  - by user1763118

  I'm having trouble installing the wireless lan service offline with a fresh installed windows 2012 server RTM. I tried "install-windowsfeature wireless-networking" in the non-gui mode and using the server manager in the gui mode to enable the wireless lan service, but both of them show a "failure configuring windows updates" message after the installation restarted the system. I checked the event log and I think messages about "The WLAN Autoconfig service depends on the following service: nativewifip. This service might not be installed" are the source of the issue. Google shows it is a service called "native wifi filter", but I cannot find anywhere to install that service. I don't have a Ethernet adapter for that computer, so have to install everything offline before the wifi's working.

  Read the article

< Previous Page | 266 267 268 269 270 271 272 273 274 275 276 277  | Next Page >