Search Results

Search found 20822 results on 833 pages for 'remote desktop gateway'.

Page 271/833 | < Previous Page | 267 268 269 270 271 272 273 274 275 276 277 278  | Next Page >

  • Re-streaming RTMP stream

    - by Yvan JANSSENS
    I have a set of local RTMP stream servers in my network, but I want them to be reachable outside. The bandwidth is too narrow to serve multiple clients on the streamservers of my network, so the idea is to pull the local RTMP streams on a computer serving as a gateway, which pushes them on his turn to a hosted streaming provider. It is not possible to let the sources of the stream push their stream directly to the server outside due to network policy restrictions. Scheme of what I'm trying to accomplish: Internal network | External network ------------ ------------ ----------------------- | internal | <---- | Gateway | ------> | streamserver outside| | streams | ------------ ----------------------- ------------ | ^ | | | ----------- | | clients | | ----------- My question now is: which application which can pull a live stream from an RTMP source (Flash Media Server) and push it to another one (Flash Media Server at hosting provider).

    Read the article

  • Multiple External IP Ranges on a Juniper SSG5

    - by Sam
    I have a Juniper SSG 5 firewall in a datacenter. The first interface (eth0/0) has been assigned a static IP address and has three other addresses configured for VIP Nat. I have a static route configured at the lowest priority for 0.0.0.0/0 to my hosting company's gateway. Now I need to configure a second IP block. I have the IPs assigned to the second interface (eth0/1) which is in the same security zone and virtual router as the first. However, with this interface enabled I (a) can't initiate outbound sessions (browse the internet, ping, DNS lookup, etc) even though I can access servers behind the firewall just fine from the outside and (b) can't ping the management IP of the firewall/gateway. I've tried anything I can think of but I guess this is a little above my head. Could anyone point me in the right direction? Interfaces: ethernet0/0 xxx.xxx.242.4/29 Untrust Layer3 ethernet0/1 xxx.xxx.152.0/28 Untrust Layer3 Routes: http://i.stack.imgur.com/60s41.png

    Read the article

  • Need assistance setting up Linux Router with 2 public lans

    - by user195407
    I was assigned a.b.c.10/30 (Public IP) for my router and given a.b.c.9 as the gateway. I was also assigned x.y.z.128/25 (Public IP block) for my use. I want to setup a Linux router to handle this situation. My Linux box has 3 NICs, eth0 is a.b.c.10, eth1 I have assigned x.y.z.254, eth2 is unused at present. I have eth1 connected to a network switch, and several devices connected. Let's say box A is x.y.z.129 with a gateway of x.y.z.254. I have not connected to the network yet, as it is not live. What settings do I need to make, beyond adding the 2 network definitions to the cards and having "route add default gw a.b.c.9 eth0"? I may add a private 192.168.100.0/24 lan to eth2 later.

    Read the article

  • How to keep variable preserve while running script through ssh

    - by Ali Raza
    I am trying to run while loop with read through ssh: #!/bin/bash ssh [email protected] "cat /var/log/syncer/rm_filesystem.log | while read path; do stat -c \"%Y %n\" "$path" >> /tmp/fs_10.10.10.10.log done" But the issue is my variable $path is resolving on my localhost where as I want to resolve it on remote host so that it can read file on remote host and take stat of all folder/files listed in "rm_filesystem.log"

    Read the article

  • Share Keyboard/Mouse between PC (windows?) and Android

    - by kashiko
    Has anyone come across software that can do this successfully/reliably? I would like to set up my Nexus 7 tablet on a stand under my monitor and use it with the mouse/KB hooked up to my desktop so I can continue to use it while using my desktop without having to pick it up. I was able to find one application which claims to do this (PC Loves Android), but reviews on the Google Play store do not seem to favor it.

    Read the article

  • "eject" command not working..

    - by shadyabhi
    shadyabhi@shadyabhi-desktop:~$ eject -v eject: using default device `cdrom' eject: device name is `cdrom' eject: expanded name is `/media/cdrom' eject: `/media/cdrom' is a link to `/media/cdrom0' eject: `/media/cdrom0' is not mounted eject: `/media/cdrom0' is not a mount point eject: tried to use `/media/cdrom0' as device name but it is no block device eject: unable to find or open device for: `cdrom' shadyabhi@shadyabhi-desktop:~$ The tray doesnt open.. How do I open tray using command line?

    Read the article

  • How do you manage private queue permissions on a windows server 2008 cluster?

    - by David
    On windows server 2003 there was an option to allow a resource to interact with the desktop, this allowed you to run computer management mmc snap-in on the virtual name of the cluster, allowing you to manage permissions of the private message queues on the cluster. Windows Server 2008 failover clustering has removed that checkbox, so applications can no longer interact with the desktop. My question is then how does one go about managing private queue permissions on the clustered (the virtual name) server?

    Read the article

  • how to run a program using command line with parameters on mac os x

    - by user36089
    Hello everyone I try to use APIKit http://ericasadun.com/2009/12/apikit-goes-beta/ to scan my codes to detect if there is private api. apiscanner should run as apiscanner ~/Desktop/MyPath/myapp.app I used command 'cd' go to the directory where apiscanner is. But if I call apiscanner ~/Desktop/MyPath/MyApp.app Last login: Sun Jun 13 07:22:07 on ttys002 unknown required load command 0x80000022 Trace/BPT trap logout Even I copy file 'apiscanner' and 'doit' to MyPath, the execute same problem I think there is somethin wrong when I run apiscanner under mac osx Welcome any comment Thanks interdev

    Read the article

  • How can I join two simple home networks together using an ethernet cable?

    - by Ilia Jerebtsov
    I want to join two different home networks together like so: PC A1 PC A2 PC B1 PC B2 \ / \ / Gateway A <----- ethr. cable -----> Gateway B | | ADSL modem A ADSL modem B Both networks are of the basic residential type with identical configuration, with all PCs running Vista/7. The point is to temporarily join two apartments in a building for gaming and file sharing, and the holy grail would be: PCs on network A can access PCs on network B and vice-versa (file shares and gaming). Each network uses its own internet connection. Data between networks shouldn't take a trip through the internet (broadband upload speeds are severely capped) A network's internet access should continue working if the joining cable is disconnected with minimal configuration changes. How closely can this be achieved?

    Read the article

  • Strange behavior when changing default shell, and setting explorer.exe as winlogon shell for specific user

    - by Ophir Yoktan
    I use a custom logon shell on a machine (windows 7) for security reasons - which works fine by altering HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon\shell. However, I also want that the administrator will still be able to manage the machine, so I modified the user specific key: HKEY_CURRENT_USER\Software\Microsoft\Windows NT\CurrentVersion\Winlogon\shell back to explorer.exe - but when I log on I get a single windows explorer window, and not the full desktop. does any one know how to configure the normal desktop shell only to a specific user?

    Read the article

  • Using 2 Transparent HAProxy for load balancing

    - by Nyxynyx
    We can configure HAProxy to be a transparent proxy by using the guide here, where one of the steps says ...to put the backend servers in a different subnet to the front end clients and make sure that the default gateway points back at the HAProxy load balancer. However when we need to have 2 transparent HAProxy in front of our balanced servers (for redundancy), it seems like this wont work as we can only set one gateway for our balanced servers. What will be the correct way to setup the system such that we can have 2 transparent HAProxy infront of the balanced servers? The main reason for having transparent proxies is the need to find the client's IP addresses over TCP.

    Read the article

  • Launching an application from Bash

    - by JBoy
    I'm right now busy with moving the first steps into Linux, i'm using a bash shell within a mac osx I see in all tutorials that in order to launch an application from the bash its necessary to cd to its directory and simply type the name of the app. This is exatly what i'm doing and it does not work (i have on my desktop a 'Eclipse' folder with the launcher icon in it): cd Desktop cd Eclipse Eclipse.app Why will this not work? I read everywhere that typing the name of the app its enough

    Read the article

  • Ubuntu box static routing problem

    - by Rafael
    Hello, I'm trying to configure a ubuntu server to be a router. This is my interface configuration (eth2 connects to my WAN, eth0 to my LAN): auto eth2 iface eth2 inet static address 192.168.0.249 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 auto eth0 iface eth0 inet static address 192.168.100.1 netmask 255.255.255.0 This is the router information: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth2 And this is dhcp configuration: subnet 192.168.100.0 netmask 255.255.255.0 { range 192.168.100.101 192.168.100.254; option domain-name-servers 201.70.86.133; option routers 192.168.100.1; authoritative; } I'm then connecting a mac os x by cable on eth0. This is en0 interface configuration: en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:26:bb:5d:82:b0 inet6 fe80::226:bbff:fe5d:82b0%en0 prefixlen 64 scopeid 0x4 inet 192.168.100.101 netmask 0xffffff00 broadcast 192.168.100.255 media: autoselect (100baseTX <full-duplex>) status: active And this is the routing table: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.100.1 UGSc 139 32 en0 10.37.129/24 link#8 UC 2 0 vnic1 10.37.129.2 0:1c:42:0:0:9 UHLWI 0 839 lo0 10.37.129.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic1 10.211.55/24 link#7 UC 2 0 vnic0 10.211.55.2 0:1c:42:0:0:8 UHLWI 0 840 lo0 10.211.55.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic0 127 127.0.0.1 UCS 0 0 lo0 127.0.0.1 127.0.0.1 UH 3 507924 lo0 169.254 link#4 UCS 0 0 en0 172.16.42/24 link#10 UC 2 0 vmnet8 172.16.42.1 0:50:56:c0:0:8 UHLWI 0 839 lo0 172.16.42.255 link#10 UHLWbI 1 24 vmnet8 192.168.100 link#4 UC 2 0 en0 192.168.100.1 0:e0:7c:7e:f:99 UHLWI 139 0 en0 777 192.168.100.101 127.0.0.1 UHS 0 0 lo0 192.168.100.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 en0 192.168.116 link#9 UC 2 0 vmnet1 192.168.116.1 0:50:56:c0:0:1 UHLWI 0 839 lo0 192.168.116.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vmnet1 When I ping 192.168.100.1, it works. When I ping 192.168.0.249, it also works. However, when I try to ping 192.168.0.1 it does not. Does anyone has any way to solve this? Is there a way to debug it? Thanks,

    Read the article

  • Is it possible to use a laptop as an external monitor?

    - by Jephir
    I need to create a multi-monitor setup for my desktop computer but I have no additional monitors with me right now, aside from my laptop. Is it possible to use my laptop screen as an external monitor? Note that I am not trying to connect a monitor to my laptop, rather, I am trying to connect my laptop screen to a desktop video card (if this is possible).

    Read the article

  • Can't ping some IP addresses in the same subnet (LAN) Windows 2011 Server

    - by Ricardo
    Hi I’m running in Windows Small Server 2011 server standard (192.168.1.108), it’s my dhcp and dns server too, but suddenly all other users can’t get internet. My gateway is 192.168.1.1. After a lots of tested I can saw that my server can’t get into the router (192.168.1.1), and also into some others computers, but some other computers answer the ping command. In fact the same computer with the IP 192.168.1.9 didn't answer, but with the IP 192.168.1.63, it response! I have no routers, firewall, vlans or anything that disallow the traffic between computers, in fact when I changed the server IP address (192.168.1.109), I be able to ping the other computers and gateway, but if a back to the 192.168.1.108 the trouble comeback. I hope you can help me with this issue Ricardo

    Read the article

  • How to use AIM to communicate with a Google Talk user?

    - by altendky
    How do I allow someone that uses the AIM desktop client to chat with someone else using the Google Talk desktop client? Both systems are Windows XP. The trick is that I don't want to have them have to change clients. Long ago I used Trillian... then Pidgin and now Meebo. But these are not solutions to the question. Also note that the Google client is not the web gadget.

    Read the article

  • How Do I Properly Run OfflineIMAP in a Crontab

    - by alharaka
    Installed Fedora. # cat /etc/redhat_release | awk ' { print F "> " $0; print ""; }' Fedora release 14 (Laughlin) Installed offlineimap from yum, cuz I'm lazy these days. # yum info offlineimap | awk ' { print F "> " $0; print ""; }' Loaded plugins: langpacks, presto, refresh-packagekit Adding en_US to language list Installed Packages Name : offlineimap Arch : noarch Version : 6.2.0 Release : 2.fc14 Size : 611 k Repo : installed From repo : fedora Summary : Powerful IMAP/Maildir synchronization and reader support URL : http://software.complete.org/offlineimap/ License : GPLv2+ Description : OfflineIMAP is a tool to simplify your e-mail reading. With : OfflineIMAP, you can read the same mailbox from multiple : computers. You get a current copy of your messages on each : computer, and changes you make one place will be visible on all : other systems. For instance, you can delete a message on your home : computer, and it will appear deleted on your work computer as : well. OfflineIMAP is also useful if you want to use a mail reader : that does not have IMAP support, has poor IMAP support, or does : not provide disconnected operation. And, lo and behold, every time I run offlineimap and try to redirect output in a crontab, it does not work. Below is my .offlineimaprc. [general] ui = TTY.TTYUI accounts = Personal, Work maxsyncaccounts = 3 [Account Personal] localrepository = Local.Personal remoterepository = Remote.Personal [Account Work] localrepository = Local.Work remoterepository = Remote.Work [Repository Local.Personal] type = Maildir localfolders = ~/mail/gmail [Repository Local.Work] type = Maildir localfolders = ~/mail/companymail [Repository Remote.Personal] type = IMAP remotehost = imap.gmail.com remoteuser = [email protected] remotepass = password ssl = yes maxconnections = 4 # Otherwise "deleting" a message will just remove any labels and # retain the message in the All Mail folder. realdelete = no [Repository Remote.Work] type = IMAP remotehost = server.company.tld remoteuser = username remotepass = password ssl = yes maxconnections = 4 I have tried TTY.TTYUI, NonInteractive.Quiet and NonInteractive.Basic with different variations. With or without redirection, the crontab entries I try cause problems. $ crontab -l | awk ' { print F "> " $0; print ""; }' */5 * * * * offlineimap >> ~/mail/logs/offlineimap.log 2>&1 */5 * * * * offlineimap I always get the same damn error ERROR: No UIs were found usable!. What am I doing wrong!?

    Read the article

  • Virtual machine on ubuntu

    - by MITHIYA MOIZ
    I have configured virtual machine on ubuntu with the help of below article, https://help.ubuntu.com/9.04/serverguide/C/libvirt.html I managed to finish all the part except the major portion getting virtual host to talk to real network, Which I guess should be done only via bridge interface. Via virtual machine manager I try to choose any interface it gives me interface not bridged When I try to bridge the interceface eth0 as below auto br0 iface br0 inet static address 192.168.0.223 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off I cannot communicate with this interface to network, host server looses all the communication to network. But when I remote bridge interface from /etc/network/interfaces And configure eth0 as below it works fine The primary network interface auto eth0 iface eth0 inet static address 192.168.0.223 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 dns-nameservers 62.215.6.51 gateway 192.168.0.1 how can i setup bridge interface correctly and how would my /etc/netwrok/interfaces file would look a like.

    Read the article

  • Mac OSX Server 10.6 DNS Issues

    - by dallasclark
    The server was upgraded from 10.5 from 10.6, during the upgrade the Reverse Zones were lost so I tried to recreate these but found that it's best to delete all zones, definitions and start again. So I've started again and Reverse Zones are appearing but I'm still having issues. I receive the following errors (if they help) 01-Nov-2010 12:52:01.254 client 192.168.1.52#57051: view com.apple.ServerAdmin.DNS.public: query (cache) 'server.dev.home.gateway/A/IN' denied 01-Nov-2010 12:59:24.487 client 192.168.1.52#52858: view com.apple.ServerAdmin.DNS.public: query (cache) 'earth.server.dev.home.gateway/A/IN' denied At the moment I have the following setup in the DNS 1.168.192.in-addr.arpa. Reverse Zone 192.168.1.100 Reverse Mapping MacPro-Server.local. server.dev. Primary Zone server.dev. Machine 192.168.1.100 earth.server.dev. Alias server.dev.

    Read the article

  • I'm looking for a linux text editor

    - by just_wes
    Preface: I like Vim... a lot Requirements: Remote editing capabilities S/FTP or SSH Text coloring As you can see my requirements are specific but slim. I have been using TextWrangler on MacOSX and I love it. It's that remote editing feature that really does it for me. This post is community-wiki, and if another topic that has an answer that meats my requirements exists, please kindly redirect me. Thank you all very much!

    Read the article

  • What equipment do real ISP's use?

    - by Allanrbo
    In a dormitory of 550 residents, people often mistakenly set up DHCP servers for the whole network by plugging in their private Wi-Fi routers wrongly. Also recently, someone mistakenly configured their PC to a static IP being the same as that of the default gateway. We use cheap 3Com switches at the moment. I know that Cisco switches support DHCP snooping to solve the DHCP problem, but that still does not solve the default gateway IP takeover problem. What sort of switch equipment do real ISP's use so their customers cannot break the network for the other customers?

    Read the article

  • Replies to request coming over a relay goes to relay's internal IP, not to original request's source IP

    - by seaquest
    Dhcpd running on Linux gets a dhcp request over dhcrelay which is running on other remote machine. Oct 6 10:09:46 2012 dhcpd: DHCPDISCOVER from 00:1e:68:06:eb:37 (oguz-U300) via 172.16.17.81 tcpdump: listening on eth1, link-type EN10MB (Ethernet), capture size 96 bytes 10:35:01.112500 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto: UDP (17), length: 328) 192.168.0.81.67 > 192.168.0.1.67: BOOTP/DHCP, Request from 00:1e:68:06:eb:37, length: 300, hops:1, xid:0xe378fc7e, flags: [none] (0x0000) Gateway IP: 172.16.17.81 Client Ethernet Address: 00:1e:68:06:eb:37 [|bootp] It matches to a subnet and send reply. However reply does not go to the requesting dhcrelay external IP(192.168.0.81). Instead, it goes to the internal interface IP of machine running dhcrelay. And I think because of this remote machine running dhcrelay or the dhcrealy itself discarding packet. Oct 6 10:09:46 2012 dhcpd: DHCPOFFER on 172.16.17.11 to 00:1e:68:06:eb:37 (oguz-U300) via 172.16.17.81 10:35:02.050108 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto: UDP (17), length: 328) 192.168.0.1.67 > 172.16.17.81.67: BOOTP/DHCP, Reply, length: 300, hops:1, xid:0xe378fc7e, flags: [none] (0x0000) Your IP: 172.16.17.11 Gateway IP: 172.16.17.81 Client Ethernet Address: 00:1e:68:06:eb:37 [|bootp] Is this a normal behaviour? Machine running dhcrelay: eth1(ext) Link encap:Ethernet HWaddr 00:90:0B:21:43:F4 inet addr:192.168.0.81 Bcast:192.168.0.255 Mask:255.255.255.0 eth2(int) Link encap:Ethernet HWaddr 00:90:0B:21:43:F5 inet addr:172.16.17.81 Bcast:172.16.17.255 Mask:255.255.255.0 3582 ? Ss 0:00 /usr/sbin/dhcrelay -i eth2 192.168.0.1 Machine running dhcpd: eth1 Link encap:Ethernet HWaddr 00:90:0B:23:97:D1 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 option domain-name "test.com"; option subnet-mask 255.255.255.0; authoritative; ignore client-updates; ddns-update-style ad-hoc; default-lease-time 86400; max-lease-time 86400; subnet 192.168.0.0 netmask 255.255.255.0 { range 192.168.0.135 192.168.0.169; option broadcast-address 192.168.0.255; option domain-name-servers 192.168.0.1; option domain-name "test.com"; option routers 192.168.0.1; } subnet 172.16.17.0 netmask 255.255.255.0 { local-address 192.168.0.1; server-identifier 192.168.0.1; range 172.16.17.10 172.16.17.11; option broadcast-address 172.16.17.255; option routers 172.16.17.81; } (I put local-address and server-identifier. But this does not help ) Regards, -- Oguz YILMAZ UPDATE: The first problem is found. I have configured dhcrelay only on listening internel interface. It seems (of course) is should also listen to external interface for replies. It appears it is not important where the packet destined to. dhrelay will forward it to internal net. HOWEVER, I have deleted route on dhcpd server to reach 172.16.17.x subnet. It again tries to send reply to 172.16.17.81. Because it does not know the route it send it from default gateway to the internet. eth0: IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto: UDP (17), length: 328) 192.168.1.2.67 > 172.16.17.81.67: BOOTP/DHCP, Reply, length: 300, hops:1, xid:0x32830125, secs:3, flags: [none] (0x0000) eth0: Your IP: 172.16.17.11 eth0: Gateway IP: 172.16.17.81 eth0: Client Ethernet Address: 00:1e:68:06:eb:37 [|bootp] How can I force dhcpd to force to send replies to requesting IP? Because, it is not much meaningful to add routes to subnet we distribute IP for. Internet - dhcpd - 192.168.0.1 - SOMENET - 192.168.0.81 - dhcrelay - 172.16.17.0/24 192.168.0.1 has no route for 172.16.17.0 and has no interface directly attached to that net.

    Read the article

  • Error running bash script - No matching processes

    - by Bashity
    I am trying to kill Xcode by running killall Xcode.app, which works normally when I run it through terminal. However, if I put it into a bash script that I keep on my Desktop called re_xcode, the script will output the following error. Please can you tell me where I am going wrong? No matching processes belonging to you were found The file /Users/Max/Desktop/Applications/Xcode.app does not exist. #!/bin/bash killall Xcode.app open ./Applications/Xcode.app

    Read the article

< Previous Page | 267 268 269 270 271 272 273 274 275 276 277 278  | Next Page >