Search Results

Search found 19446 results on 778 pages for 'network printer'.

Page 275/778 | < Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >

• Wireless broken after latest 12.04 update

  - by inderpaldeol

  I updated 12.04 yesterday and it broke my wireless connection. iwconfig lo no wireless extensions. eth0 no wireless extensions. l@ubuntu:~$ lspci|grep Network 03:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe In the hardware drivers, I see - rt3090sta is activated but currently not in use. WICD does not show wireless networks. Can someone help me please? Thanks id

  Read the article

• Problem connecting to certain wifi networks

  - by Romas

  I'm using lenovo u300s (it has Intel Centrino Wireless-N 1030 card), and I can connect to wireless network at home with no problem, but I can not connect to any networks at my university. I'm not sure if it's the case but most of university networks are open and you need to sign up your username as you enter browser. There is also an eudoroam network, but I can not connect to it either. Any suggestions? Yes I have the latest ubuntu version.

  Read the article

• What would you do if there was no Internet? [closed]

  - by Jinjavajin

  If the International Network no longer functioned how would programmers cope? Would software development become an intractable problem? So much development has been achieved because of our interconnectivity that we might not be able to go forward as a community, without it. Is this the case, or might we become more productive due to the removal of a major distraction? How would we cope if the the network went down?

  Read the article

• Unix ? Linux ????????? Oracle Database 11g Release 2 ? SAP ????????

  - by ?? ?

  US?Blog Oracle Database 11g Release 2 is SAP certified for Unix and Linux platforms. ?????????SAP??????Oracle Database 11g R2????????? ????UNIX???Linux???????????????? Linux x86???x86-64 AIX HP-UX IA64 Solaris SPARC???x64 ??? ?????????????????????????! Advanced Compression Option (table, RMAN backup, expdp, DG Network) Real Application Testing Oracle Database 11g Release 2 Database Vault Oracle Database 11g Release 2 RAC Advanced Encryption for tablespaces, RMAN backups, expdp, DG Network Direct NFS Deferred Segments Online Patching ????SAP???1398634 ??????????????????

  Read the article

• Mac OS X behind OpenLDAP and Samba

  - by Sam Hammamy

  I have been battling for a week now to get my Mac (Mountain Lion) to authenticate on my home network's OpenLDAP and Samba. From several sources, like the Ubuntu community docs, and other blogs, and after a hell of a lot of trial and error and piecing things together, I have created a samba.ldif that will pass the smbldap-populate when combined with apple.ldif and I have a fully functional OpenLDAP server and a Samba PDC that uses LDAP to authenticate the OS X Machine. The problem is that when I login, the home directory is not created or pulled from the server. I get the following in system.log Sep 21 06:09:15 Sams-MacBook-Pro.local SecurityAgent[265]: User info context values set for sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got ruser: (null) Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got service: authorization Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): no authauth availale for user. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): failed: 7 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Failed to determine Kerberos principal name. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Done cleanup3 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Kerberos 5 refuses you Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): pam_sm_authenticate: ntlm Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_acct_mgmt(): OpenDirectory - Membership cache TTL set to 1800. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_record_check_pwpolicy(): retval: 0 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Establishing credentials Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Context initialised Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): pam_sm_setcred: ntlm user sam doesn't have auth authority All that's great and good and I authenticate. Then I get CFPreferences: user home directory for user kCFPreferencesCurrentUser at /Network/Servers/172.17.148.186/home/sam is unavailable. User domains will be volatile. Failed looking up user domain root; url='file://localhost/Network/Servers/172.17.148.186/home/sam/' path=/Network/Servers/172.17.148.186/home/sam/ err=-43 uid=9000 euid=9000 If you're wondering where /Network/Servers/IP/home/sam comes from, it's from a couple of blogs that said the OpenLDAP attribute apple-user-homeDirectory should have that value and the NFSHomeDirectory on the mac should point to apple-user-homeDirectory I also set the attr apple-user-homeurl to <home_dir><url>smb://172.17.148.186/sam/</url><path></path></home_dir> which I found on this forum. Any help is appreciated, because I'm banging my head against the wall at this point. By the way, I intend to create a blog on my vps just for this, and create an install script in python that people can download so no one has to go through what I've had to go through this week :) After some sleep I am going to try to login from a windows machine and report back here. Thanks Sam

  Read the article

• Mac OS X behind OpenLDAP and Samba

  - by Sam Hammamy

  I have been battling for a week now to get my Mac (Mountain Lion) to authenticate on my home network's OpenLDAP and Samba. From several sources, like the Ubuntu community docs, and other blogs, and after a hell of a lot of trial and error and piecing things together, I have created a samba.ldif that will pass the smbldap-populate when combined with apple.ldif and I have a fully functional OpenLDAP server and a Samba PDC that uses LDAP to authenticate the OS X Machine. The problem is that when I login, the home directory is not created or pulled from the server. I get the following in system.log Sep 21 06:09:15 Sams-MacBook-Pro.local SecurityAgent[265]: User info context values set for sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got ruser: (null) Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got service: authorization Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): no authauth availale for user. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): failed: 7 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Failed to determine Kerberos principal name. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Done cleanup3 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Kerberos 5 refuses you Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): pam_sm_authenticate: ntlm Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_acct_mgmt(): OpenDirectory - Membership cache TTL set to 1800. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_record_check_pwpolicy(): retval: 0 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Establishing credentials Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Context initialised Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): pam_sm_setcred: ntlm user sam doesn't have auth authority All that's great and good and I authenticate. Then I get CFPreferences: user home directory for user kCFPreferencesCurrentUser at /Network/Servers/172.17.148.186/home/sam is unavailable. User domains will be volatile. Failed looking up user domain root; url='file://localhost/Network/Servers/172.17.148.186/home/sam/' path=/Network/Servers/172.17.148.186/home/sam/ err=-43 uid=9000 euid=9000 If you're wondering where /Network/Servers/IP/home/sam comes from, it's from a couple of blogs that said the OpenLDAP attribute apple-user-homeDirectory should have that value and the NFSHomeDirectory on the mac should point to apple-user-homeDirectory I also set the attr apple-user-homeurl to <home_dir><url>smb://172.17.148.186/sam/</url><path></path></home_dir> which I found on this forum. Any help is appreciated, because I'm banging my head against the wall at this point. By the way, I intend to create a blog on my vps just for this, and create an install script in python that people can download so no one has to go through what I've had to go through this week :) After some sleep I am going to try to login from a windows machine and report back here. Thanks Sam

  Read the article

• Why do I see a large performance hit with DRBD?

  - by BHS

  I see a much larger performance hit with DRBD than their user manual says I should get. I'm using DRBD 8.3.7 (Fedora 13 RPMs). I've setup a DRBD test and measured throughput of disk and network without DRBD: dd if=/dev/zero of=/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 4.62985 s, 116 MB/s / is a logical volume on the disk I'm testing with, mounted without DRBD iperf: [ 4] 0.0-10.0 sec 1.10 GBytes 941 Mbits/sec According to Throughput overhead expectations, the bottleneck would be whichever is slower, the network or the disk and DRBD should have an overhead of 3%. In my case network and I/O seem to be pretty evenly matched. It sounds like I should be able to get around 100 MB/s. So, with the raw drbd device, I get dd if=/dev/zero of=/dev/drbd2 bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 6.61362 s, 81.2 MB/s which is slower than I would expect. Then, once I format the device with ext4, I get dd if=/dev/zero of=/mnt/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 9.60918 s, 55.9 MB/s This doesn't seem right. There must be some other factor playing into this that I'm not aware of. global_common.conf global { usage-count yes; } common { protocol C; } syncer { al-extents 1801; rate 33M; } data_mirror.res resource data_mirror { device /dev/drbd1; disk /dev/sdb1; meta-disk internal; on cluster1 { address 192.168.33.10:7789; } on cluster2 { address 192.168.33.12:7789; } } For the hardware I have two identical machines: 6 GB RAM Quad core AMD Phenom 3.2Ghz Motherboard SATA controller 7200 RPM 64MB cache 1TB WD drive The network is 1Gb connected via a switch. I know that a direct connection is recommended, but could it make this much of a difference? Edited I just tried monitoring the bandwidth used to try to see what's happening. I used ibmonitor and measured average bandwidth while I ran the dd test 10 times. I got: avg ~450Mbits writing to ext4 avg ~800Mbits writing to raw device It looks like with ext4, drbd is using about half the bandwidth it uses with the raw device so there's a bottleneck that is not the network.

  Read the article

• Archlinux/atheros WLAN configuration troubles

  - by GrinReaper

  I'm trying to config archlinux to use my wireless network adapter. It's quite troublesome. From what I've gathered, it's an atheros network adapter, using the ath5k driver/module... I can't get it to work; any ideas? Here's some of the output from my tinkering: # lspci | grep -i net 00:0a.0 Ethernet controller: nVidia corporation MCP67 Ethernet (reva2) 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) # lsusb ... Bus 004 Device 003: ID 03f0:17d Hewlett Packard Wireless (Bluetooth + WLAN Interface [Integrated Module] # ping -c 3 www.google.com ping: unknown host www.google.com #ping -c 3 8.8.8.8 ping: network is unreachable # lspci -v 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) ... Kernel driver in use: ath5k Kernel modules: ath5k # dmesg |grep ath5k registered as phy0 registered led device ath5k: atheros chip found PCI INT A disabled registered led device registered as phy1 # ip addr | sed '/^[0-9]/!d;s/: <.*$//' 1: lo 2: eth1 3: eth0 # ip link set <interface> up/down RNETLINK answers: Operation not possible due to RF-kill Also, is there a way to dump text from command-line to a text file so i can just copy pasta? Sorry, first time using a linux distro... EDIT: So I just tried this: I actually just did this twice. (I can't tell which setting is on/off for my wireless adapter. The lights are blue all the time now.) #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :yes 1: hp-bluetooth: bluetooth softblocked: no hardblocked :yes 3: phy1: wireless lan softblocked: no hardblocked :yes #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :no 1: hp-bluetooth: bluetooth softblocked: no hardblocked no 3: phy1: wireless lan softblocked: no hardblocked :yes 7: hci0: bluetooh 0: hp-wifi: wireless lan softblocked: no hardblocked :no I've dug around some other articles and it seems like ath5k is supposed to be preferable to madwifi, so should i be using madwifi? I'm 99% sure I disabled the hardblock (by turning it ON) but, as shown above, phy1 wireless lan is STILL hardblocked. What gives? Maybe I've made some more fundamental error in a basic config file? EDIT: I've fixed the hardblock. I've tried pinging www.google.com, but to no avail. I get: ping: unknown host www.google.com In the arch wiki: Edit /etc/hosts and add the same HOSTNAME you entered in /etc/rc.conf: 127.0.0.1 archlinux.domain.org localhost.localdomain localhost archlinux To my understanding, hostname is just a user-specified and based on preference(?) My /etc/rc.conf: HOSTNAME="gestalt" My /etc/hosts: 127.0.0.1 localhost.localdomain localhost gestalt but should it be the following? 120.0.0.1 localhost.domain.org localhost.localdomain localhost gestalt

  Read the article

• Troubleshooting an unstable internet connection

  - by Konrad Rudolph

  My MacBook Pro running OS X (10.9, but I had the same problem before) is connected to a Belkin router via WiFi and, using Virgin Media as the ISP, to the internet. The connection is extremely unstable – on some days, I get a ping timeout every few seconds. In addition, some domains seem to suffer general connectivity issues. For instance, I often find that while the youtube.com website loads, none of the videos (which are hosted on a separate domain) do. At other times, videos load but always fail to buffer, even though the actual connection speed is ok, even though I’ve disabled dash playback. Since I’m living in a rented room and the ISP contract isn’t actually mine I’ve got only limited possibilities of addressing the problem. In particular, I have no access to the router configuration and my non tech savvy landlady, while sympathetic, is not in a great hurry to hand the problem over to the ISP’s customer support. What’s more, I seem to be the only person in the house experiencing these problems – but I can imagine that this is simply because I’m the only one who’s using the internet continuously. I’m searching for specific tests that might be able to pinpoint – and ideally solve – the problem. So far all I’ve managed to do is establish that Virgin is routing my traffic in mysterious ways. Here’s an excerpt from traceroute google.co.uk. It’s worth mentioning that the host name doesn’t seem to matter a lot, the trace route is always the same. traceroute: Warning: google.co.uk has multiple addresses; using 62.254.36.148 traceroute to google.co.uk (62.254.36.148), 64 hops max, 52 byte packets 1 (192.168.2.1) 1.112 ms 1.300 ms 2.359 ms 2 10.100.32.1 (10.100.32.1) 11.926 ms 10.217 ms 24.987 ms 3 cmbg-core-1a-ae3-610.network.virginmedia.net (80.1.202.93) 28.809 ms * 66.653 ms 4 popl-bb-1b-ae16-0.network.virginmedia.net (212.43.163.141) 13.759 ms 126.504 ms 20.472 ms 5 nrth-bb-1b-et-010-0.network.virginmedia.net (62.253.175.57) 28.357 ms 16.398 ms 42.387 ms 6 nrth-bb-1c-ae1-0.network.virginmedia.net (62.253.174.110) 27.441 ms 15.622 ms 12.044 ms 7 lutn-icdn-1-ae0-0.network.virginmedia.net (62.253.175.82) 16.678 ms 28.463 ms 28.253 ms 8 * * * 9 * * * 10 * * * ^C If I let it, this goes on until the end of time. It never seems to reach a destination. Is this normal? A friend living in the same town who is also with Virgin Media has a more conventional traceroute output: 7 hops to google.co.uk, all of which send the ICMP TIME_EXCEEDED response. The obvious fix – rebooting the router – doesn’t seem to help. As far as I can tell, the WiFi connection is stable (I can always ping the router) so the problem is further downstream. I’ve tried using an alternative DNS before (OpenDNS) but if anything, this made things worse. In fact, it made all Google services nigh unreachable.

  Read the article

• DHCP server with multiple interfaces on ubuntu, destroys default gateway

  - by Henrik Kjus Alstad

  I use Ubuntu, and I have many interfaces. eth0, which is my internet connection, and it gets its info from a DHCP-server totally outisde of my control. I then have eth1,eth2,eth3 and eth4 which I have created a DHCP-server for.(ISC DHCP-Server) It seems to work, and I even get an IP-address from the foreign DHCP-server on the internet facing interface. However, for some reason it seems my gateway for eth0 became screwed after I installed my local DHCP-server for eth1-eth4. (I think so because I got an IP for eth0, and I can ping other stuff on the local network, but I cannot get access to the internet). My eth0-specific info in /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 10.0.1.1 netmask 255.255.255.0 network 10.0.1.0 broadcast 10.0.1.255 gateway 10.0.1.1 mtu 8192 auto eth2 iface eth2 inet static address 10.0.2.1 netmask 255.255.255.0 network 10.0.2.0 broadcast 10.0.2.255 gateway 10.0.2.1 mtu 8192 My /etc/default/isc-dhcp-server: INTERFACES="eth1 eth2 eth3 eth4" So why does my local DHCP-server fuck up the gateway for eth0, when I tell it not to listen to eth0? Anyone see the problem or what I can do to fix it? The problem seems indeed to be the gateways. "netstat -nr" gives: 0.0.0.0 --- 10.X.X.X ---- 0.0.0.0 --- UG 0 0 0 eth3 It should have been 0.0.0.0 129.2XX.X.X 0.0.0.0 UG 0 0 0 eth0 So for some reason, my local DHCP-server overrides the gateway I get from the network DHCP. Edit: dhcp.conf looks like this(I included info only for eth1 subnet): ddns-update-style none; not authoritative; subnet 10.0.1.0 netmask 255.255.255.0 { interface eth1; option domain-name "example.org"; option domain-name-servers ns1.example.org, ns2.example.org; default-lease-time 600; max-lease-time 7200; range 10.0.1.10 10.0.1.100; host camera1_1 { hardware ethernet 00:30:53:11:24:6E; fixed-address 10.0.1.10; } host camera2_1 { hardware ethernet 00:30:53:10:16:70; fixed-address 10.0.1.11; } } Also, it seems that the gateway is correctly set if I run "/etc/init.d/networking restart" in a terminal, but that's not helpful for me, I need the correct gateway to be set during startup, and i'd rather find the source of the problem

  Read the article

• Can't ping devices by IP address for devices allocated IPs by DHCP

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The Domain Controller/DNS server is a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. The network has been set up for a couple of years and usually works fine. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. The router UI shows that the laptop has a reserved IP allocated via DHCP. All machines either have a static or DHCP allocated IP on the 192.168.0.* subnet. Router - 192.168.0.1 - Static - Wired Windows Domain Controller - 192.168.0.8 - Static - Virtual Windows 7 Workstation - 192.168.0.200 - DHCP Auto - Wired VMWare ESXi Host - 192.168.0.201 - Static? - Wired iPhone 1 - 192.168.0.202 - DHCP Auto - WiFi iPhone 2 - 192.168.0.203 - DHCP Auto - WiFi Windows Vista Laptop - 192.168.0.204 - DHCP Reserved - WiFi Using the Windows 7 machine (200), I try to ping each machine and the only DHCP machine that responds is itself. The other DHCP machines fail with Reply from 192.168.0.200: Destination host unreachable.. Using nslookup fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the Windows 2000 Domain Controller (8), I try to ping each machine and the only DHCP machine that responds is the Windows 7 machine (200). Pinging the other DHCP machines fails with Request timed out.. Using nslookup also fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the iPhone 2 (203), I try to ping (Network Ping Lite) the machines with static IP addresses and that works fine. When I try to ping the Windows 7 machine (200) it is unable to get a response. How do I configure the DNS server/Windows Domain/Router properly so that the Windows Domain machines can see the IPs allocated via DHCP?

  Read the article

• Windows 7 laptop constantly dropping internet connection

  - by Corbin Holbert

  I have scoured the web for an answer and failed to find one. I am using a Toshiba Satellite laptop running Windows 7 64-Bit. I have the computer connected via Wifi. Now, I am no beginner with the Internet, or anything related to computers, as I have grown up teaching everyone around me how to use computers, and went to college for IT. Everything on my network works flawlessly at all times, except for this evil laptop. The worst part is that I fixed this once before a few years back and recently had to replace the hard drive and re-install the OS, but cannot for the life of me remember what I did to make this problem go away. I am in my browser, connected to the Internet. I click a link. Suddenly no internet access. All I do is click down on the WiFi connection in the task bar, disconnect and reconnect immediately. Internet is back the moment I hit "connect." I have read many people had the same issues as I am having, but they all had triggers or other network issues. I have no trigger (this happens literally five to six times per minute no matter what I am doing) and I have no problems with my router, modem, or any other devices or computers on said network. As I am a web designer, and like to test my work live at every turn- this is going to result in this laptop being in pieces if I can't get it fixed soon. If more info is needed, let me know and I will provide. Thanks for any help offered! EDIT: Network Card: Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC Network state reads as "No Internet Access" when the problem first occurs, then magically I have Internet access for about ten seconds once I disconnect and reconnect. I have turned off IPV6, I have turned off power saving options for the network adapter, no viruses. Any new ideas? Also, I had to disconnect and reconnect four times just to get to this edit screen- and will likely have to do the same just to post it- it's that bad.

  Read the article

• VPN Connection causes DNS to use wrong DNS server

  - by Bryan

  I have a Windows 7 PC on our company network (which is a member of our Active Directory). Everything works fine until I open a VPN connection to a customer's site. When I do connect, I lose network access to shares on the network, including directories such as 'Application Data' that we have a folder redirection policy for. As you can imagine, this makes working on the PC very difficult, as desktop shortcuts stop working, software stops working properly due to having 'Application Data' pulled from under it. Our network is routed (10.58.5.0/24), with other local subnets existing within the scope of 10.58.0.0/16. The remote network is on 192.168.0.0/24. I've tracked the issue down to being DNS related. As soon as I open the VPN tunnel, all my DNS traffic goes via the remote network, which explains the loss of local resources, but my question is, how can I force local DNS queries to go to our local DNS servers rather than our customers? The output of ipconfig /all when not connected to the VPN is below: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled This is the output of the same command with the VPN tunnel connected: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local PPP adapter Customer Domain: Connection-specific DNS Suffix . : customerdomain.com Description . . . . . . . . . . . : CustomerDomain Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.85(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.0.16 192.168.0.17 Primary WINS Server . . . . . . . : 192.168.0.17 NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled Routing table Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.58.5.1 10.58.5.89 20 10.58.5.0 255.255.255.0 On-link 10.58.5.89 276 10.58.5.89 255.255.255.255 On-link 10.58.5.89 276 10.58.5.255 255.255.255.255 On-link 10.58.5.89 276 91.194.153.42 255.255.255.255 10.58.5.1 10.58.5.89 21 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 192.168.0.95 192.168.0.85 21 192.168.0.85 255.255.255.255 On-link 192.168.0.85 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.58.5.89 276 224.0.0.0 240.0.0.0 On-link 192.168.0.85 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.58.5.89 276 255.255.255.255 255.255.255.255 On-link 192.168.0.85 276 The binding order for the interfaces is as follows: I've not configured the VPN tunnel to use the default gateway at the remote end, and network comms to nodes on both networks are fine. (i.e. I can ping any node on our network or the remote network). I've modified the PPTP connection properties to use the DNS servers 10.58.3.32 followed by 192.168.0.16, yet the query still goes to 192.168.0.16. Edit: The local resources that disappear are hosted on domain DFS roots, which might (or might not) be relevant.

  Read the article

• Download - Upload is too slow on Centos

  - by Mehdi

  My download/upload in server and out of server is too slow (around 50 KB/s !) ! Did I miss some configuration ? Some information: CentOS release 6.3 uptime load average: 0.17, 0.32, 0.37 Memory free -m total used free shared buffers cached Mem: 24009 21988 2021 0 806 18098 -/+ buffers/cache: 3083 20926 Swap: 4095 28 4067 lshw -C network *-network description: Ethernet interface product: 82574L Gigabit Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 00 serial: 00:25:90:70:17:4a size: 100MB/s capacity: 1GB/s width: 32 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=off broadcast=yes driver=e1000e driverversion=1.9.5-k duplex=full firmware=2.1-2 ip=108.175.8.123 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:16 memory:fb900000-fb91ffff ioport:e000(size=32) memory:fb920000-fb923fff ethtool ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off MDI-X: off Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000001 (1) Link detected: yes dmesg |grep e1000e dmesg |grep e1000e e1000e: Intel(R) PRO/1000 Network Driver - 1.9.5-k e1000e: Copyright(c) 1999 - 2012 Intel Corporation. e1000e 0000:02:00.0: Disabling ASPM L0s e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 e1000e 0000:02:00.0: setting latency timer to 64 e1000e 0000:02:00.0: irq 33 for MSI/MSI-X e1000e 0000:02:00.0: irq 34 for MSI/MSI-X e1000e 0000:02:00.0: irq 35 for MSI/MSI-X e1000e 0000:02:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:70:17:4a e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: Unsupported Speed/Duplex configuration e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: Disabling ASPM L1 e1000e 0000:02:00.0: eth0: changing MTU from 1500 to 9000 e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO

  Read the article

• Apache + Tomcat error 120006 Using mod_proxy_ajp for Load Balance

  - by Wakaru44

  I have an apache 2 frontend with two nodes, and a backend with two instances of tomcat 6 balance with mod_proxy_ajp. The bbdd is in a separate machine. All machines use RHEL, 6.2 on the frontend, 5.5 on the backend. The infraestructure is virtualized using VMware. # This is the apache config in one of the virtualHost. ProxyPreserveHost On ProxyPass / balancer://liferay/ <Proxy balancer://liferay> BalancerMember ajp://lrab:8009 route=liferaya BalancerMember ajp://lrbb:8009 route=liferayb status=+H ProxySet lbmethod=byrequests nofailover=on </Proxy> The conector in tomcat is now configured like this: <!-- Define an AJP 1.3 Connector on port 8009 --> <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" URIEncoding="UTF-8" enableLookups="false" allowTrace="true" /> Do you think it could be useful to set a maxThreads parameter, like in this post?? in that case, How can i determine a proper number of threads? From time to time, we get errors like this [Tue Sep 18 17:57:02 2012] [error] ajp_read_header: ajp_ilink_receive failed [Tue Sep 18 17:57:02 2012] [error] (120006)APR does not understand this error code: proxy: read response failed from 192.168.1.104:8009 (lrab) And apache switches to the pasive node (if its active) or fails with 503. Some things i have tried so far: I think that i have some performance issues with one of the applications, Here you can see a threadDump But i'm not quite sure about it. I also started to monitor the network connection. I have noticed that there are some pings lost when i have a "ping -f " so maybe it could be a network issue, but the success rate is 100% (so the lost packets are only a few among the flood, but maybe, i don't know, enough to break the link betwen apache and tomcat). I wrote a python script to check connectivity with timestamps on the pings, so i can know when the network fails. After sniffing the network , i can also see some RST packets, but i don't know if that is a normal behaviour (some applications do that to end a network communication). I have also noticed that the applications have problems communicating with the database, but im not even sure if this could be related or not. If you think so, i can post more info about it. I changed the connector on the tomcats to use the native one, but still the same. I need not even a solution to this, but maybe some guidance on how can i troubleshoot this better ¿Analyze threads, monitor mysql performance, sniff the traffic between apaches and tomcats? Ultimately, all i need is to balance the tomcat instances in Active/pasive mode, so if there is another way to do it, i could give it a try.

  Read the article

• Checking the configuration of two systems to determine changes

  - by None

  We are standing up a replicant data center at work and need to ensure that the new data center is configured (nearly) identically to the original. The new data center will be differently addressed and named than the original and will have differing user accounts, but all the COTS, patches, and configurations should be the same. We would normally ghost the original servers and install those images onto the new machines, however, we have a few problematic pieces of COTS that require we install them outside of an image due to how they capture the setup of the network during their installation and maintain it within their configuration information (in some cases storing it in various databases). We have tried multiple times and this piece of COTS cannot be captured within a ghost image unless the destination machine will have an identical network setup (all the same IPs, hostnames, user accounts, etc across the entire network) as the original. In truth, it is the setup of these special COTS that I want to audit the most because they are difficult to install and configure in the first place. In light of the fact that we can’t simply ghost, I’m trying to find a reasonable manner to audit the new data center and check to see if it is setup like the original (some sort of system wide configuration audit or integrity check). I’m considering using something like Tripwire for Servers to capture the configuration on the source machines and then run an audit on the destination machines. I understand that it will still show some differences due to the minor config changes, but I’m hoping that it will eliminate the majority of the work. Here are some of the constraints I’m working under: Data center is comprised of multiple Windows and Linux machines of differing versions (about 20 total) I absolutely cannot ghost or snap any other type of image of these machines … at least not in their final configuration I want to audit the final configuration to ensure all of the COTS, patches, configurations, etc are installed and setup properly (as compared to the original data center) I would rather not install any additional tools on these machines … I’d much rather run it from a standalone machine or off a DVD Price of tools is important but not an impossible burden, however, getting a solution soon is important (I can’t take the time to roll my own tools to do this) For the COTS that stores the network information, I don’t know all of the places it stores the network information … so it would be unlikely I could find a way in the near future to adjust its setup after the installation has occurred Anyone have any thoughts or alternate approaches? Can anyone recommend tools that would be usable for system wide configuration audits?

  Read the article

• Secure openVPN using IPTABLES

  - by bob franklin smith harriet

  Hey, I setup an openVPN server and it works ok. The next step is to secure it, I opted to use IPTABLES to only allow certain connections through but so far it is not working. I want to enable access to the network behind my openVPN server, and allow other services (web access), when iptables is disabaled or set to allow all this works fine, when using my following rules it does not. also note, I already configured openVPN itself to do what i want and it works fine, its only failing when iptables is started. Any help to tell me why this isnt working will appreciated here. These are the lines that I added in accordance with openVPN's recommendations, unfortunately testing these commands shows that they are requiered, they seem incredibly insecure though, any way to get around using them? # Allow TUN interface connections to OpenVPN server -A INPUT -i tun+ -j ACCEPT #allow TUN interface connections to be forwarded through other interfaces -A FORWARD -i tun+ -j ACCEPT # Allow TAP interface connections to OpenVPN server -A INPUT -i tap+ -j ACCEPT # Allow TAP interface connections to be forwarded through other interfaces -A FORWARD -i tap+ -j ACCEPT These are the new chains and commands i added to restrict access as much as possible unfortunately with these enabled, all that happens is the openVPN connection establishes fine, and then there is no access to the rest of the network behind the openVPN server note I am configuring the main iptables file and I am paranoid so all ports and ip addresses are altered, and -N etc appears before this so ignore that they dont appear. and i added some explanations of what i 'intended' these rules to do, so you dont waste time figuring out where i went wrong : 4 #accepts the vpn over port 1192 -A INPUT -p udp -m udp --dport 1192 -j ACCEPT -A INPUT -j INPUT-FIREWALL -A OUTPUT -j ACCEPT #packets that are to be forwarded from 10.10.1.0 network (all open vpn clients) to the internal network (192.168.5.0) jump to [sic]foward-firewall chain -A FORWARD -s 10.10.1.0/24 -d 192.168.5.0/24 -j FOWARD-FIREWALL #same as above, except for a different internal network -A FORWARD -s 10.10.1.0/24 -d 10.100.5.0/24 -j FOWARD-FIREWALL # reject any not from either of those two ranges -A FORWARD -j REJECT -A INPUT-FIREWALL -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT-FIREWALL -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT-FIREWALL -j REJECT -A FOWARD-FIREWALL -m state --state RELATED,ESTABLISHED -j ACCEPT #80 443 and 53 are accepted -A FOWARD-FIREWALL -m tcp -p tcp --dport 80 -j ACCEPT -A FOWARD-FIREWALL -m tcp -p tcp --dport 443 -j ACCEPT #192.168.5.150 = openVPN sever -A FOWARD-FIREWALL -m tcp -p tcp -d 192.168.5.150 --dport 53 -j ACCEPT -A FOWARD-FIREWALL -m udp -p udp -d 192.168.5.150 --dport 53 -j ACCEPT -A FOWARD-FIREWALL -j REJECT COMMIT now I wait :D

  Read the article

• No Telnet login prompt when used over SSH tunnel

  - by SCO

  Hi there ! I have a device, let's call it d1, runnning a lightweight Linux. This device is NATed by my internet box/router, hence not reachable from the Internet. That device runs a telnet daemon on it, and only has root as user (no pwd). Its ip address is 192.168.0.126 on the private network. From the private network (let's say 192.168.0.x), I can do: telnet 192.168.0.126 Where 192.168.0.126 is the IP address in the private network. This works correctly. However, to allow administration, I'd need to access that device from outside of that private network. Hence, I created an SSH tunnel like this on d1 : ssh -R 4455:localhost:23 ussh@s1 s1 is a server somewhere in the private network (but this is for testing purposes only, it will endup somewhere in the Internet), running a standard Linux distro and on which I created a user called 'ussh'. s1 IP address is 192.168.0.48. When I 'telnet' with the following, let's say from c1, 192.168.0.19 : telnet -l root s1 4455 I get : Trying 192.168.0.48... Connected to 192.168.0.48. Escape character is '^]'. Connection closed by foreign host . The connection is closed after roughly 30 seconds, and I didn't log. I tried without the -l switch, without any success. I tried to 'telnet' with IP addresses instead of names to avoid reverse DNS issues (although I added to d1 /etc/hosts a line refering to s1 IP/name, just in case), no success. I tried on another port than 4455, no success. I gathered Wireshark logs from s1. I can see : s1 sends SSH data to c1, c1 ACK s1 performs an AAAA DNS request for c1, gets only the Authoritave nameservers. s1 performs an A DNS request, then gets c1's IP address s1 sends a SYN packet to c1, c1 replies with a RST/ACK s1 sends a SYN to c1, C1 RST/ACK (?) After 0.8 seconds, c1 sends a SYN to s1, s1 SYN/ACK and then c1 ACK s1 sends SSH content to d1, d1 sends an ACK back to s1 s1 retries AAAA and A DNS requests After 5 seconds, s1 retries a SYN to c1, once again it is RST/ACKed by c1. This is repeated 3 more times. The last five packets : d1 sends SSH content to s1, s1 sends ACK and FIN/ACK to c1, c1 replies with FIN/ACK, s1 sends ACK to c1. The connection seems to be closed by the telnet daemon after 22 seconds. AFAIK, there is no way to decode the SSH stream, so I'm really stuck here ... Any ideas ? Thank you !

  Read the article

• unable to join domain using virtualbox

  - by FreshPrinceOfSO

  I'm in the process of setting up a VM environment for a MS certification exam (70-462). Following the training kit's instructions, I've set up a domain controller (DC) and two members (SQL-A, SQL-B) thus far. I can't figure out why I can't join the domain. DC IPv4 Address . . . : 10.10.10.10(Preferred) Subnet Mask. . . . : 255.0.0.0 DNS Servers. . . . : ::1 127.0.0.1 SQL-A IPv4 Address . . . : 10.10.10.20(Preferred) Subnet Mask. . . . : 255.0.0.0 DNS Servers. . . . : 10.10.10.10 SQL-B IPv4 Address . . . : 10.10.10.30(Preferred) Subnet Mask. . . . : 255.0.0.0 DNS Servers. . . . : 10.10.10.10 I've read how to do networking between virtual machines in virtualbox and the documentation. After trying various network adapter configurations, I can't get them to communicate in order to have the two members join the domain. When I ping from .30 to .10, I get: ping 10.10.10.10 Pinging 10.10.10.10 with 32 bytes of data: Reply from 10.10.10.20: Destination host unreachable. Reply from 10.10.10.20: Destination host unreachable. Reply from 10.10.10.20: Destination host unreachable. Reply from 10.10.10.20: Destination host unreachable. Trying to join the domain: netdom join SQL-A /domain:contso.com The specified domain either does not exist or could not be contacted. The command failed to complete successfully. Within VirtualBox, I've tried the following combinations for network adapter: Attached to - Promiscuous Mode ------------------------------- NAT Bridged Adapter - Deny Bridged Adapter - Allow VMs Bridged Adapter - Allow All Internal Network - Deny Internal Network - Allow VMs Internal Network - Allow All Host-only Adapter - Deny Host-only Adapter - Allow VMs Host-only Adapter - Allow All Edit ipconfig /all of DC ipconfig /all of SQL-A

  Read the article

• Looking for a NTP Server Software for Windows

  - by Simon

  I'm looking for a, preferably free, NTP Server for Windows Server 2003/2008. We have already tried the built in Windows Time Server, but our tests did show that it is not very accurate, we see time differences up to 500ms. The max time difference we can allow for our application is ~100ms. Now we have already used the Meinberg NTPd for Windows. It works great except we have one big issue with it: If there is a network connection problem between the client and server, the ntp server is in a panic state It won't give the client a new time until we restart the ntp service. This is a big issue which has caused us some trouble. It was working fine for months until there was a network problem we didn't notice, we only noticed it after a week when the time difference was already 30 sec. on the clients. So please suggest some alternative NTP Server for windows. I did Google but I get a lot of unrelated search results. Edit: So far the ntpd windows version was very accurate and I'd like to stick with it. The only problem is the "panic state" after a network disconnect. Maybe some knows here what the cause of this is and how to fix it. Also, I forgot to mention that we have a server/client setup like this: Server1 -- Server2 -- Server3 -- Client1 -- Client2 -- Client3 So Server2 gets its time from Server1, Server3 gets its time from Server2, and the Clients get their time from Server3. Also, there are clients connected directly to Server2. It is important that all Servers and Clients have the exact same time (within ~100ms) Now there was a network problem with Server3 and its clients. The servers run the ntpd port for Windows, which acts as NTP server and client. The clients have Dimension4 as NTP client. After the network problem, the error message in D4 was something like this (out the top of my head, don't have the exact error message): Server response: The server is in a panic state (could not sync clock) I read through the ntpd docs, and the only mention of "panic" is when the time difference is 10000 seconds which will cause to exit the ntpd server but this was not the case. Also there is a "-g" command line switch to disable the panic exit, but it is already set by default. Any ideas what could cause the panic state and how to get rid of it next time?

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• Mysql Servers for Attendance System

  - by foo

  I'm building an attendance system. There are about 20 places where people will check in and check out using Mifare 1K Card. It will use MySQL as the database. The system will display something like "#ID IN: 800AM" when the first time the user checks in and "#ID OUT: 400PM" when the user checks out. For this to work, all the databases need to be synchronized with each other all the times. For an example, if user A went to location #1 to check in but by the time he wants to return home, the server at location #1 went down, he needs to go to location #2 or the nearest server to check out. The server at location #2 should display '#ID OUT: 400PM" and not "#ID IN: 400PM" since he's already checked in. So, what should I use to ensure this idea will work? My main concern is with the network (other department manages it) which is very unpredictable. It just love to go down anytime it wants to. Update LOL, didn't realize my question is not clear, just noticed it when you guys pointed it out, sorry about that. My real question is, how can I configure my MySQL to be synchronized with each other (20 servers)? MySQL cluster ? (tried reading about it, but I'm not sure if it's the right thing to do) My current setup (first phase): Local database for each server OS: Slackware A main server that keeps track which staff is at which server A web based front end for the user to see their history (which connects to the server based on their records) Main Pros No worries about network problems since it is a local database Main Cons A user can only check in and out at the same server. Databases/Servers are not connected with each others. Have to add the user to each server if the users want to check in at different locations. Which means, if he wants to go to location A, he must be checked out from location A first and then check in at location B. The server at location B didn't know that the user has checked in before at A. By the way, I've already centralized my NTP to a local server. About the network, let's just say, I don't have the authority to make changes so that the network will be better. The network won't effect all 20 servers at once, usually, just a few of them for several times a week. If there are anything else you would like me to answer, please just ask.

  Read the article

• Port forwarding not working properly

  - by sudo work

  I'm trying to host a small web server from my home network; however, I have not been able to successfully port forward ports to the local server. My current network topology looks like this: Cable Modem/Router - Secondary Wireless Router - Many computers (including server) The modem/router I'm using is a Cisco (Scientific Atlantic) DPC2100, provided by my ISP. The wireless router that I'm using as the central hub to my home network is a Linksys E3000. The computer being used as a server is running Ubuntu 10.04 Server Edition. The main issue is that I can't access the server remotely, using my WAN IP address. I have port forwarded my wireless router; however, I believe that I need to somehow set my modem to bridge mode. As far as I can tell though, this isn't possible. Here are the various IP address settings: DPC2100 WAN: 69.xxx.xxx.xxx Internal IP: 192.168.100.1 Internal Network: 192.168.7.0 E3000 IP Address: 192.168.7.2 Gateway: 192.168.7.1 Internal IP: 192.168.1.1 Internal Network: 192.168.1.0 Server IP Address: 192.168.1.123 Gateway: 192.168.1.1 Now I can do an nmap at various nodes, and here are the results (from the server): nmap localhost: 22,25,53,80,110,139,143,445,631,993,995,3306,5432,8080 open nmap 192.168.7.2: 22,25,80 (filtered),110,139,445 open (ports I have forwarded in the E3000)* nmap 69.xxx.xxx.xxx: 1720 open *For some reason, I can SSH into the server at 192.168.7.2, but not view the website. Here are also some other settings: /etc/hosts/ 127.0.0.1 localhost 127.0.1.1 servername ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/apache2/sites-available/default snippet <VirtualHost *:80> DocumentRoot /srv/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> ... </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> ... </Directory> ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> ... </Directory> </VirtualHost> Let me know if you need any other information; some stuff probably slipped my mind.

  Read the article

• 40k Event Log Errors an hour Unknown Username or bad password

  - by ErocM

  I am getting about 200k of these an hour: An account failed to log on. Subject: Security ID: SYSTEM Account Name: TGSERVER$ Account Domain: WORKGROUP Logon ID: 0x3e7 Logon Type: 4 Account For Which Logon Failed: Security ID: NULL SID Account Name: administrator Account Domain: TGSERVER Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x334 Caller Process Name: C:\Windows\System32\svchost.exe Network Information: Workstation Name: TGSERVER Source Network Address: - Source Port: - Detailed Authentication Information: Logon Process: Advapi Authentication Package: Negotiate Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols. - Key length indicates the length of the generated session key. This will be 0 if no session key was requested. On my server... I changed my adminstrative username to something else and since then I've been inidated with these messages. I found on http://technet.microsoft.com/en-us/library/cc787567(v=WS.10).aspx that the 4 means "Batch logon type is used by batch servers, where processes may be executing on behalf of a user without their direct intervention." which really doesn't shed any light on it for me. I checked the services and they are all logging in as local system or network service. Nothing for administrator. Anyone have any idea how I tell where these are coming from? I would assume this is a program that is crapping out... Thanks in advance!

  Read the article

< Previous Page | 271 272 273 274 275 276 277 278 279 280 281 282  | Next Page >