Search Results

Search found 8042 results on 322 pages for 'days'.

Page 278/322 | < Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >

• LUKS with LVM, mount is not persistent after reboot

  - by linxsaga

  I have created a Logical vol and used luks to encrypt it. But while rebooting the server. I get a error message (below), therefore I would have to enter the root pass and disable the /etc/fstab entry. So mount of the LUKS partition is not persistent during reboot using LUKS. I have this setup on RHEL6 and wondering what i could be missing. I want to the LV to get be mount on reboot. Later I would want to replace it with UUID instead of the device name. Error message on reboot: "Give root password for maintenance (or type Control-D to continue):" Here are the steps from the beginning: [root@rhel6 ~]# pvcreate /dev/sdb Physical volume "/dev/sdb" successfully created [root@rhel6 ~]# vgcreate vg01 /dev/sdb Volume group "vg01" successfully created [root@rhel6 ~]# lvcreate --size 500M -n lvol1 vg01 Logical volume "lvol1" created [root@rhel6 ~]# lvdisplay --- Logical volume --- LV Name /dev/vg01/lvol1 VG Name vg01 LV UUID nX9DDe-ctqG-XCgO-2wcx-ddy4-i91Y-rZ5u91 LV Write Access read/write LV Status available # open 0 LV Size 500.00 MiB Current LE 125 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 [root@rhel6 ~]# cryptsetup luksFormat /dev/vg01/lvol1 WARNING! ======== This will overwrite data on /dev/vg01/lvol1 irrevocably. Are you sure? (Type uppercase yes): YES Enter LUKS passphrase: Verify passphrase: [root@rhel6 ~]# mkdir /house [root@rhel6 ~]# cryptsetup luksOpen /dev/vg01/lvol1 house Enter passphrase for /dev/vg01/lvol1: [root@rhel6 ~]# mkfs.ext4 /dev/mapper/house mke2fs 1.41.12 (17-May-2010) Filesystem label= OS type: Linux Block size=1024 (log=0) Fragment size=1024 (log=0) Stride=0 blocks, Stripe width=0 blocks 127512 inodes, 509952 blocks 25497 blocks (5.00%) reserved for the super user First data block=1 Maximum filesystem blocks=67633152 63 block groups 8192 blocks per group, 8192 fragments per group 2024 inodes per group Superblock backups stored on blocks: 8193, 24577, 40961, 57345, 73729, 204801, 221185, 401409 Writing inode tables: done Creating journal (8192 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 21 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override. [root@rhel6 ~]# mount -t ext4 /dev/mapper/house /house PS: HERE I have successfully mounted: [root@rhel6 ~]# ls /house/ lost+found [root@rhel6 ~]# vim /etc/fstab -> as follow /dev/mapper/house /house ext4 defaults 1 2 [root@rhel6 ~]# vim /etc/crypttab -> entry as follows house /dev/vg01/lvol1 password [root@rhel6 ~]# mount -o remount /house [root@rhel6 ~]# ls /house/ lost+found [root@rhel6 ~]# umount /house/ [root@rhel6 ~]# mount -a -> SUCCESSFUL AGAIN [root@rhel6 ~]# ls /house/ lost+found Please let me know if I am missing anything here. Thanks in advance.

  Read the article

• How to install 32-bit libraries using Debian Testing

  - by bgoodr

  Question: What is the way to determine, ahead of time and without doing a full install of 64-bit Debian Testing NETINST, when Debian Testing has 32-bit libraries available and fully working and installable so that the following command works without broken package errors?: apt-get install ia32-libs ia32-libs-gtk The errors that occur when 32-bit libraries are not available, still in some broken state, or whatever is broken are detailed below. I already have concluded that "Just install Stable" is my stop-gap measure for now, but I would like to know the answer to the above question so as to avoid a lengthy installation process only to run into these problems at the very end. Details: I downloaded the 64-bit Debian Testing netinst a couple of days ago. This was "Jessie" built 20131014-06:07 via http://tinyurl.com/lejpa. This is weekly testing build. Yes, I know I should expect problems, and I did. I managed to get it completely installed and was able to invoke into GNOME, but not get past the 32-bit library problem. The problems starts when I attempt to install the 32-bit libraries via: apt-get install ia32-libs ia32-libs-gtk that returns: root@breath:~# apt-get install ia32-libs ia32-libs-gtk Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 but it is not installable ia32-libs-gtk : Depends: ia32-libs-i386 but it is not installable Depends: ia32-libs-gtk-i386 but it is not installable E: Unable to correct problems, you have held broken packages. I then found an old (2012 is old to me) answer at ia32-libs : Depends: ia32-libs-i386 but it is not installable and even tried what they suggested there which was dpkg --add-architecture i386 apt-get update After executing the above, I tried again but got: root@breath:~# apt-get install ia32-libs ia32-libs-gtk Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 ia32-libs-gtk : Depends: ia32-libs-i386 E: Unable to correct problems, you have held broken packages. root@breath:~# And then tried this: root@breath:~# dpkg --get-selections | grep hold And that returned nothing. Not only is there broken packages, the system doesn't even know what packages are broken, so Debian Stable is my only solution I know of right now. Hence my question above.

  Read the article

• Adaptec 5805 after reboot don't starting

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not included. It only works if the computer is shut down and turn off. Late i update firmware "Adaptec RAID 5805 Firmware Build 18948" How to fix the problem? add Log Configuration summary Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priorityHigh Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1 List item

  Read the article

• Server load spikes several times a day, load average for the past month is 5 times the load average all year

  - by AMF

  My Munin notifications set up for our (Debian) LAMP cluster have been notifying me continuously that our load on our production machine has been at dangerous levels. While the average load all year typically runs between 2 and 8, the load in the past month and only the past month -- has been skyrocketing to 10, 18, and occasionally even 50-60. The spikes last only 5-10 minutes at a time and occur about every 2-3 hours. The spikes do not effect performance only because I have a script that sends traffic off our server to a mirror CDN when the load goes above 10. I've looked for cron jobs that correlate with this timeframe but there is nothing I can see that would cause this. Site traffic is also normal (we receive about 200K visits per day). I'm also trying to think of anything I've changed around the time this problem began, and I really cannot think of anything. This is probably not much to go on. Maybe there is a clue in the top print-out (below) that I'm not seeing. How do I proceed to find the cause? -- Typical top when the load is NOT spiking: top - 11:13:09 up 472 days, 25 min, 1 user, load average: 6.08, 4.29, 3.80 Tasks: 105 total, 1 running, 104 sleeping, 0 stopped, 0 zombie Cpu(s): 41.2%us, 5.8%sy, 0.0%ni, 49.5%id, 2.7%wa, 0.1%hi, 0.7%si, 0.0%st Mem: 3369592k total, 2166980k used, 1202612k free, 559504k buffers Swap: 2650684k total, 1892k used, 2648792k free, 1129116k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 32046 apache 15 0 36300 12m 9828 S 20 0.4 0:01.97 apache2 32679 apache 15 0 36568 13m 10m S 19 0.4 0:01.69 apache2 31441 apache 15 0 36616 13m 10m S 19 0.4 0:04.13 apache2 31477 apache 15 0 36596 13m 9.8m S 15 0.4 0:01.99 apache2 31993 apache 15 0 36876 16m 12m S 12 0.5 0:02.01 apache2 31782 apache 15 0 36836 14m 10m S 8 0.4 0:02.17 apache2 32198 apache 15 0 36536 13m 10m S 7 0.4 0:01.59 apache2 880 apache 15 0 36508 9708 6236 S 7 0.3 0:00.42 apache2 31945 apache 17 0 36876 16m 13m S 5 0.5 0:03.17 apache2 32197 apache 16 0 36636 10m 7504 S 5 0.3 0:02.70 apache2 32326 apache 15 0 37024 11m 7632 S 5 0.3 0:02.15 apache2 32565 apache 15 0 37280 13m 9.8m S 5 0.4 0:03.75 apache2 32676 apache 15 0 36896 16m 12m S 4 0.5 0:00.95 apache2 32678 apache 15 0 36536 12m 9692 S 4 0.4 0:02.27 apache2 974 apache 16 0 37064 9888 6016 D 4 0.3 0:00.13 apache2 32150 apache 16 0 36832 13m 10m S 3 0.4 0:01.74 apache2 31780 apache 16 0 36848 11m 7660 S 3 0.3 0:02.87 apache2

  Read the article

• "Error loading operating system": Win7/Vista

  - by LookitsPuck

  Have this computer for about 2 years now. Originally had Vista installed, now have Windows 7 installed. Both on separate hard drives. Also have another drive used strictly for media. About a week ago, the Vista hard drive started going on its way out. Was getting problems on startup. After a few BIOS settings, I was able to get into Windows 7 and everything was fine. However, I started remembering the startup issues, so I deleted the bootup for Vista under msconfig. Didn't restart the computer at that time, though. For a few days, everything was ok. Last night I play a little poker, then hit the hay. I wake up to a good ole "Error loading operating system" on the screen. Just wonderful. Looks like the computer restarted overnight (auto updates, anyone?). So, after a big of finagling and half hearted tries, I can't get past the "Error loading operating system" screen. FWIW, in the BIOS it can see my hard drives fine. So I move on. I get my Windows 7 installation disk to try and do a repair. Go in the BIOS, change boot priority to DVD drive, and we're on our merry way. After loading from the disc, I first try jumping into the "Repair your computer" section. That opens up the System Recovery Options. However, this is where the problem comes into play. I don't see any operating systems here. Nada. What's odd though is if I click on the Load Drivers button, I can see my Windows 7 partition (C:), and can go through the files and folders without issue. What do I do at this point? I can't repair it. It seems like I can traverse the hard drive without issue when in an open dialog in the System Recovery Options, but I'm getting the good ole "Error loading computer" on bootup. Suggestions? Thanks all!!

  Read the article

• KeePass justification

  - by Jeff Walker

  I work at a place that tries to take security seriously, but sadly, they often fail. Currently, one of the major ways they fail is password management. I personally have about 20 accounts (my personal user id on lots of machines). For shared "system" accounts, there are about 45 per environment; development, test, and production. I have access to 2 of those, so my personal total is somewhere around 115 accounts. Passwords have to be at least 15 characters with some extensive but standard complexity constraints, and have to be changed every 60 days or so (system accounts every year). They also should not be the same for different accounts, but that isn't enforced. Think DoD-type standards. There is no way to remember and keep up with this. It just isn't humanly possible, as far as I'm concerned. This might be a good justification of a centralized account management system, a la LDAP or ActiveDirectory, but that is a totally different battle. Currently the solution is an Excel spreadsheet. They use Excel to put a password on it, and then most people make a copy and remove the password. This makes my stomach turn. I use KeePass for this problem and it manages all of my account very well. I like the features like auto-typing, grouping, plugins, password generation, etc. It uses AES-256 encryption via the .Net framework, and while not FIPS compliant, it has a very good reputation. The only problem is that they are also very careful about using randomly downloaded software. So we have to justify every piece of software on our workstations. I have been told that they really don't want me to use this, be cause of the "sensitive nature" of storing passwords. sigh My justification has to be "VERY VERY strong". I have been tasked with writing a justification for KeePass, but as I am lazy, I would like any input that I can get from the community. What do you recommend? Is there something out there that is better or more respected than KeePass? Is there any security experts saying interesting things on this topic? Anything will help at this point. Thanks.

  Read the article

• Cannot access a very specific site from my router

  - by DJDarkViper

  This is a problem for me because this site is important to me. It's MY website. And sadly my email is hosted on my site (which I cant access either) When I try to access my website when connected to my Linksys E3000 router, these days it simply just doesn't go through. When I ping it, its all Request Timed Out, and when I tracert C:\Users\Kyle>tracert blackjaguarstudios.com Tracing route to blackjaguarstudios.com [199.188.204.228] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms CISCO26565 [192.168.1.1] 2 16 ms 15 ms 11 ms 11.4.64.1 3 11 ms 9 ms 11 ms rd1cs-ge1-2-1.ok.shawcable.net [64.59.169.2] 4 20 ms 21 ms 22 ms 66.163.76.98 5 37 ms 36 ms 35 ms rc1nr-tge0-9-2-0.wp.shawcable.net [66.163.77.54] 6 112 ms 84 ms 85 ms rc2ch-pos9-0.il.shawcable.net [66.163.76.174] 7 86 ms 89 ms 90 ms rc4as-ge12-0-0.vx.shawcable.net [66.163.64.46] 8 90 ms 84 ms 85 ms eqix.xe-3-3-0.cr2.iad1.us.nlayer.net [206.223.115.61] 9 97 ms 97 ms 99 ms xe-3-3-0.cr1.atl1.us.nlayer.net [69.22.142.105] 10 128 ms 128 ms 126 ms ae1-40g.ar1.atl1.us.nlayer.net [69.31.135.130] 11 101 ms 97 ms 96 ms as16626.xe-2-0-5-102.ar1.atl1.us.nlayer.net [69.31.135.46] 12 100 ms 97 ms 197 ms 6509-sc1.abstractdns.com [207.210.114.166] 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 * * * Request timed out. 17 * * * Request timed out. 18 * * * Request timed out. 19 * * * Request timed out. 20 * * * Request timed out. 21 * * * Request timed out. 22 * * * Request timed out. 23 * * * Request timed out. 24 * * * Request timed out. 25 * * * Request timed out. 26 * * * Request timed out. 27 * * * Request timed out. 28 * * * Request timed out. 29 * * * Request timed out. 30 * * * Request timed out. Trace complete. C:\Users\Kyle> SHAW Cable being my ISP. Figuring this was all something to do with some setting I made on the router, I reset the thing back to factory defaults. Nope. So I'm at a bit of a loss what to do here, as NO device (Computers, Laptops, Tablets, Phones, PS3/ 360, etc) can access my site or its features, so it's not just my computer either. But every other site is just fine. When I connect to my neighbors router, the site comes up just fine. And shes with SHAW as well. What should I do?!

  Read the article

• Why are emails sent from my applications being marked as spam?

  - by Brian

  Hi. I have 2 web apps running on the same server. The first is www.nimikri.com and the other is www.hourjar.com. Both apps share the same IP address (75.127.100.175). My server is through a shared hosting company. I've been testing my apps, and at first all my emails were being delivered to me just fine. Then a few days ago every email from both apps got dumped into my spam box (in gmail and google apps). So far the apps have just been sending emails to me and nobody else, so I know people aren't manually flagging them as spam. I did a reverse DNS lookup for my IP and the results I got were these: 100.127.75.in-addr.arpa NS DNS2.GNAX.NET. 100.127.75.in-addr.arpa NS DNS1.GNAX.NET. Should the reverse DNS lookup point to nimikri.com and hourjar.com, or are they set up fine the way they are? I noticed in the email header these 2 lines: Received: from nimikri.nimikri.com From: Hour Jar <[email protected]> Would the different domain names be causing gmail to think this is spam? Here is the header from one of the emails. Please let me know if any of this looks like a red flag for spam. Thanks. Delivered-To: [email protected] Received: by 10.231.157.85 with SMTP id a21cs54749ibx; Sun, 25 Apr 2010 10:03:14 -0700 (PDT) Received: by 10.151.130.18 with SMTP id h18mr3056714ybn.186.1272214992196; Sun, 25 Apr 2010 10:03:12 -0700 (PDT) Return-Path: <[email protected]> Received: from nimikri.nimikri.com ([75.127.100.175]) by mx.google.com with ESMTP id 28si4358025gxk.44.2010.04.25.10.03.11; Sun, 25 Apr 2010 10:03:11 -0700 (PDT) Received-SPF: neutral (google.com: 75.127.100.175 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=75.127.100.175; Authentication-Results: mx.google.com; spf=neutral (google.com: 75.127.100.175 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] Received: from nimikri.nimikri.com (localhost.localdomain [127.0.0.1]) by nimikri.nimikri.com (8.14.3/8.14.3) with ESMTP id o3PH3A7a029986 for <[email protected]>; Sun, 25 Apr 2010 12:03:11 -0500 Date: Sun, 25 Apr 2010 12:03:10 -0500 From: Hour Jar <[email protected]> To: [email protected] Message-ID: <[email protected]> Subject: [email protected] has invited you to New Event MIME-Version: 1.0 Content-Type: text/html; charset=us-ascii Content-Transfer-Encoding: 7bit

  Read the article

• Windows 7 Bluescreen: IRQ_NOT_LESS_OR_EQUAL | athrxusb.sys

  - by wretrOvian

  I'd left my system on last night, and found the bluescreen in the morning. This has been happening occasionally, over the past few days. Details: ================================================== Dump File : 022710-18236-01.dmp Crash Time : 2/27/2010 8:46:44 AM Bug Check String : DRIVER_IRQL_NOT_LESS_OR_EQUAL Bug Check Code : 0x000000d1 Parameter 1 : 00000000`00001001 Parameter 2 : 00000000`00000002 Parameter 3 : 00000000`00000000 Parameter 4 : fffff880`06b5c0e1 Caused By Driver : athrxusb.sys Caused By Address : athrxusb.sys+760e1 File Description : Product Name : Company : File Version : Processor : x64 Computer Name : Full Path : C:\Windows\minidump\022710-18236-01.dmp Processors Count : 2 Major Version : 15 Minor Version : 7600 ================================================== HiJackThis ("[...]" indicates removed text; full log [posted to pastebin][1]): Logfile of Trend Micro HijackThis v2.0.2 Scan saved at 8:49:15 AM, on 2/27/2010 Platform: Unknown Windows (WinNT 6.01.3504) MSInternet Explorer: Internet Explorer v8.00 (8.00.7600.16385) Boot mode: Normal Running processes: C:\Windows\DAODx.exe C:\Program Files (x86)\Asus\EPU\EPU.exe C:\Program Files\Asus\TurboV\TurboV.exe C:\Program Files (x86)\PowerISO\PWRISOVM.EXE C:\Program Files (x86)\OpenOffice.org 3\program\soffice.exe C:\Program Files (x86)\OpenOffice.org 3\program\soffice.bin D:\Downloads\HijackThis.exe C:\Program Files (x86)\uTorrent\uTorrent.exe R1 - HKCU\Software\Microsoft\Internet Explorer\[...] [...] O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files (x86)\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [HDAudDeck] C:\Program Files (x86)\VIA\VIAudioi\VDeck\VDeck.exe -r O4 - HKLM\..\Run: [StartCCC] "C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static\CLIStart.exe" MSRun O4 - HKLM\..\Run: [TurboV] "C:\Program Files\Asus\TurboV\TurboV.exe" O4 - HKLM\..\Run: [PWRISOVM.EXE] C:\Program Files (x86)\PowerISO\PWRISOVM.EXE O4 - HKLM\..\Run: [googletalk] C:\Program Files (x86)\Google\Google Talk\googletalk.exe /autostart O4 - HKLM\..\Run: [AdobeCS4ServiceManager] "C:\Program Files (x86)\Common Files\Adobe\CS4ServiceManager\CS4ServiceManager.exe" -launchedbylogin O4 - HKCU\..\Run: [uTorrent] "C:\Program Files (x86)\uTorrent\uTorrent.exe" O4 - HKUS\S-1-5-19\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-19\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-20\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'NETWORK SERVICE') O4 - HKUS\S-1-5-20\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'NETWORK SERVICE') O4 - Startup: OpenOffice.org 3.1.lnk = C:\Program Files (x86)\OpenOffice.org 3\program\quickstart.exe O13 - Gopher Prefix: O23 - Service: @%SystemRoot%\system32\Alg.exe,-112 (ALG) - Unknown owner - C:\Windows\System32\alg.exe (file missing) O23 - Service: AMD External Events Utility - Unknown owner - C:\Windows\system32\atiesrxx.exe (file missing) O23 - Service: Asus System Control Service (AsSysCtrlService) - Unknown owner - C:\Program Files (x86)\Asus\AsSysCtrlService\1.00.02\AsSysCtrlService.exe O23 - Service: DeviceVM Meta Data Export Service (DvmMDES) - DeviceVM - C:\Asus.SYS\config\DVMExportService.exe O23 - Service: @%SystemRoot%\system32\efssvc.dll,-100 (EFS) - Unknown owner - C:\Windows\System32\lsass.exe (file missing) O23 - Service: ESET HTTP Server (EhttpSrv) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\EHttpSrv.exe O23 - Service: ESET Service (ekrn) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\x86\ekrn.exe O23 - Service: @%systemroot%\system32\fxsresm.dll,-118 (Fax) - Unknown owner - C:\Windows\system32\fxssvc.exe (file missing) O23 - Service: FLEXnet Licens

  Read the article

• Messages stuck in SMTP queue - Exchange 2003

  - by Diav

  I need your help people ;-) I have a problem with messages coming into our Exchange Server and ones going out through it. Basically, the messages are stuck in the SMTP queue. A message will come into the server, I can see it listed under "Exchange System Manager", but if you list the properties of the message queue it says something like 00:10 SMTP Message queued for local delivery 00:10 SMTP Message delivered locally to [email protected] 00:10 SMTP Message scheduled to retry local delivery 00:11 SMTP Message delivered locally to [email protected] 00:11 SMTP Message scheduled to retry local delivery etc etc For outgoing message list looks like this: 10:55 SMTP: Message Submitted to Advanced Queuing 10:55 SMTP: Started Message Submission to Advanced Queue 10:55 SMTP: Message Submitted to Categorizer 10:55 SMTP: Message Categorized and Queued for Routing 10:55 SMTP: Message Routed nad Queued for Remote Delivery And the end - since then status didn't change, message is in queue, I am forcing connection from time to time but without an effect. I checked connection with smarthost (used telnet for that) and everything seems to work correctly, so the problem is probably on exchange side. I am using Exchange Server 2003 running on Small Business Server 2003. I don't have any antivirus installed on server. Remaining free space on each partition is over 3Gb, on partition with data bases - it is over 12Gb. All was working good and without problems since 2005, problems started in half of this june - messages started going out and being stuck almost randomly (I don't see a pattern yet, some are going out, some are not, some are going after several hours). I don't know what to do, what to check more, so please, any ideas? Best regards, D. edit Priv1.edb has 14,5GB and priv1.stm 2,6GB - together those files have more than 16GB - can it be the reason? If yes, then what? Indeed, I haven't thought that it can have something in common with my problem, but several users reported recent problems with Outlook Web Access - they can log in, they see the list of their mails, but they can't see the content of their emails. Although when they are connecting with Outlook 2003/2007 - there is no such problem, only with OWA there is. edit2 So,.. It works now, and I have to admit that I am not really sure what the problem was (hope it won't come back). What have I done: Cleaned up some mailboxes to reduce size of them Dismounted Information Store Defragmentated data base files ( I used eseutil: c:\program files\exchsrvr\bin eseutil /d g:\data base\Exchsrvr\MDBDATA\priv1.edb ) Mounted Information Store back ..and before I managed to do anything else - my queue started moving, elements which were kept there already for days - started moving and after few minutes everything was sent, both, outside and locally. But: priv1.edb is still big (13 884 203 008), priv1.stm as well (2 447 384 576), so this is probably not the issue of size of the file. And if not this, so what was that? And if that was issue of size of the file, then soon it will repeat - is there something I can do to avoid it ?

  Read the article

• Share 3G connection over WiFi-LAN network

  - by kush.impetus

  This is how I have established network between my PC and my laptop at home (being novice in networking, it took me few days to achieve the feat). And it is working perfectly. I can easily share files between them. Laptop IP Address: 192.168.1.4 Subnet mask: 255.255.255.0 Default Gateway: 192.168.1.2 Desktop IP Address: 192.168.1.5 Subnet mask: 255.255.255.0 Default Gateway: 192.168.1.2 ASUS RT-N10+ Router IP Address: 192.168.1.4 Default Gateway: 192.168.1.2 I have connected the Desktop PC to the router using a LAN cable, and laptop to router over WiFi. Both, PC and laptop are running on Windows 7 OS, are on same HomeGroup, have same username / password. Also, I have connected the Ethernet cable to LAN port 1 of the router. Click here to view a graphical representation of the network. Can't post image here, because I don't have 10 reputation points. Now, what I want is use connect to Internet using a 3G USB modem on one device and share it over the network on the other. I tried Huawei and Micromax 3G USB modem. Both obtain a new IP address whenever I connect to Internet (means they have dynamic IPs). Rest, both have Subnet Mask as 255.255.255.255 and Default Gateway as 0.0.0.0. In that case, I cannot directly share Internet from the modem. Preferred DNS is blank for now in both, laptop and PC. What I am planning to do is to connect to Internet on laptop using the 3G modem and share the Internet connection over laptop's Wi-Fi (as hotspot) using Connectify, which I have done already. That, I suppose, will broadcast a static IP to connect to. Now what I can't figure out is that what changes should I make to the network settings of the router and the PC so that PC connects to the Internet broadcast by Connectify? Is that possible on the first hand? Please note that I am trying to implement the network without spending anything extra (for purchasing as USB WiFi adapter for PC, of course, which could have made the life lot easier for me). Thanks in advance

  Read the article

• My server freezes within a few hours of logging out. Staying logged in keeps the server running

  - by HappyEngineer

  I have an Ubuntu Godaddy server I use to host mail and webapps. It started having problems a couple months ago. It would lock up and stop responding to anything. I couldn't ssh into it, so I'd have godaddy power cycle the server. I have never seen anything that looked suspicious in the var logs (although I'm no expert at reading them). An fsck turned up no problems. Godaddy replaced the ram, but found no hardware problems. I started logging the output from "top" to a log file and found that even that stops running when the server freezes. Now, here is the crazy part: It got so bad that it would actually go down every few hours, but then it stopped going down. I eventually realized I had left an ssh terminal logged into the machine running top. This seemed unlikely to be a reason, but after the server was up with no problems for a full week (remember, it had been going down after just a few hours), I disconnected from the ssh session. Lo and behold, within a few hours the server froze again! I had them power cycle again and then left another ssh session open with top. It has been going without problems for 8 days now. I told others about this and they hardly believe me. I simply can't imagine what is going on. I don't know what else to try other than to just get a new server and reinstall everything. Does anyone have any ideas about what I can look for to determine what the cause is? Is it possible there's some sort of exploit on the server which only runs if everyone is logged out of the system? EDIT: The power management gone haywire sounds plausible, so I've modified the /boot/grub/menu.lst to boot with acpi=off and apm=off. It appears to have prevented kacpid and kacpid_notify from being in the process list, so I assume I did that right. I've disconnected all my sessions from the server. I'll check later tonight to see if it's still up. If it goes down then I'll try the pinging process idea. EDIT: It went down again. It lasted about a day. I've had them reboot, so now I'll try running "nohup ping -i 5 google.com &" and then disconnect. If it goes down again I'll come back. Hopefully someone will have some more ideas.

  Read the article

• Ubuntu Server 10.04 Heavy Network Traffic causes disconnect

  - by K Vaughan

  I'm currently running a headless Ubuntu 10.04 server. Installed is the LAMP stack, Joomla, Virtualbox, phpvirtualbox, webmin and proFTP.. It resolves the IP address so I can access it remotely (either the apache2 webserver or the FTP) using DDClient. Any packages installed have been installed using apt-get. Webmin, although discouraged in Ubuntu Server, is used mostly to administer the webserver aspect. This issue also appeared when I was using Ubuntu Server 10.10. After periods of heavy network traffic, whether local or remote, the connect drops. I'm talking specifically about the transfer of files via FTP, SCP or Samba (the latter of which I seldom use). There is no response to ping or ssh. I can't FTP to the server nor can I load the website. There are times when the server has been on for a few days and everything runs fine because I haven't accessed it much, if at all (thus not much network traffic). I've gone through a few hardware changes although I don't believe this has cause the issue: this has been happening long before I made any changes. At first I thought it was my ISP-provided router blocking traffic because of some kind of misconfiguration (perhaps assuming it was some kind of DoS attack). I've changed routers and still found no success. I've checked syslog, dmesg and kern.log for warnings but have uncovered none. I've ran memtest via the GRUB2 menu at boot and once it turned up 4 errors. I ran again with individual sticks of RAM in various slots and everything turned up fine. I've looked through the BIOS settings and everything looks fine. I've tried unplugging unnecessary pieces of hardware (other internal hard drives, CD drives, floppy, PCI cards, etc). Any help or tips on how I can even begin to troubleshoot this would be very much appreciated. Please note that i've only started playing with servers as a hobby so my knowledge wouldn't be the most refined. I'm comfortable with command line and have the initiative to know how to look up something I can't do. Unfortunately I can't seem to find any issues like this. Additionally: If a solution can't be found some assistance to write a script that will cause the server to reboot automatically if, after x minutes, it gets no response to pinging somewhere like google. Admittedly that's not the cleanest solution should my internet end up going down but I can't think of what else to do.

  Read the article

• Troubleshooting an unstable internet connection

  - by Konrad Rudolph

  My MacBook Pro running OS X (10.9, but I had the same problem before) is connected to a Belkin router via WiFi and, using Virgin Media as the ISP, to the internet. The connection is extremely unstable – on some days, I get a ping timeout every few seconds. In addition, some domains seem to suffer general connectivity issues. For instance, I often find that while the youtube.com website loads, none of the videos (which are hosted on a separate domain) do. At other times, videos load but always fail to buffer, even though the actual connection speed is ok, even though I’ve disabled dash playback. Since I’m living in a rented room and the ISP contract isn’t actually mine I’ve got only limited possibilities of addressing the problem. In particular, I have no access to the router configuration and my non tech savvy landlady, while sympathetic, is not in a great hurry to hand the problem over to the ISP’s customer support. What’s more, I seem to be the only person in the house experiencing these problems – but I can imagine that this is simply because I’m the only one who’s using the internet continuously. I’m searching for specific tests that might be able to pinpoint – and ideally solve – the problem. So far all I’ve managed to do is establish that Virgin is routing my traffic in mysterious ways. Here’s an excerpt from traceroute google.co.uk. It’s worth mentioning that the host name doesn’t seem to matter a lot, the trace route is always the same. traceroute: Warning: google.co.uk has multiple addresses; using 62.254.36.148 traceroute to google.co.uk (62.254.36.148), 64 hops max, 52 byte packets 1 (192.168.2.1) 1.112 ms 1.300 ms 2.359 ms 2 10.100.32.1 (10.100.32.1) 11.926 ms 10.217 ms 24.987 ms 3 cmbg-core-1a-ae3-610.network.virginmedia.net (80.1.202.93) 28.809 ms * 66.653 ms 4 popl-bb-1b-ae16-0.network.virginmedia.net (212.43.163.141) 13.759 ms 126.504 ms 20.472 ms 5 nrth-bb-1b-et-010-0.network.virginmedia.net (62.253.175.57) 28.357 ms 16.398 ms 42.387 ms 6 nrth-bb-1c-ae1-0.network.virginmedia.net (62.253.174.110) 27.441 ms 15.622 ms 12.044 ms 7 lutn-icdn-1-ae0-0.network.virginmedia.net (62.253.175.82) 16.678 ms 28.463 ms 28.253 ms 8 * * * 9 * * * 10 * * * ^C If I let it, this goes on until the end of time. It never seems to reach a destination. Is this normal? A friend living in the same town who is also with Virgin Media has a more conventional traceroute output: 7 hops to google.co.uk, all of which send the ICMP TIME_EXCEEDED response. The obvious fix – rebooting the router – doesn’t seem to help. As far as I can tell, the WiFi connection is stable (I can always ping the router) so the problem is further downstream. I’ve tried using an alternative DNS before (OpenDNS) but if anything, this made things worse. In fact, it made all Google services nigh unreachable.

  Read the article

• Excessive CPU Utilization for Bind 9.8.1 `named` processes

  - by justinzane

  I just noticed that named is eating vast amounts of CPU time for a very small network with only a few domains. Can someone help me determine what is misconfigured, please? Or how to debug this. top top - 14:13:08 up 25 days, 14:16, 1 user, load average: 1.04, 1.04, 1.05 Tasks: 149 total, 1 running, 148 sleeping, 0 stopped, 0 zombie %Cpu(s): 17.3 us, 4.3 sy, 0.0 ni, 78.2 id, 0.1 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 2042776 total, 1347916 used, 694860 free, 249396 buffers KiB Swap: 3976080 total, 30552 used, 3945528 free, 574164 cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 17445 bind 20 0 244m 42m 3124 S 99.4 2.2 2345:03 named rndc stats +++ Statistics Dump +++ (1352931389) ++ Incoming Requests ++ 65869 QUERY ++ Incoming Queries ++ 31809 A 241 NS 3 CNAME 27455 SOA 276 PTR 123 MX 462 TXT 5400 AAAA 7 A6 1 DS 14 DNSKEY 15 SPF 55 AXFR 8 ANY ++ Outgoing Queries ++ [View: internal] 22206 A 509 NS 10 SOA 25 PTR 12 MX 524 TXT 4851 AAAA 62 DNSKEY 19 SPF 3157 DLV [View: external] 87 A 2 NS 80 AAAA 120 DNSKEY 7 DLV [View: _bind] ++ Name Server Statistics ++ 65869 IPv4 requests received 27670 requests with EDNS(0) received 112 TCP requests received 65652 responses sent 20 truncated responses sent 27670 responses with EDNS(0) sent 62920 queries resulted in successful answer 37117 queries resulted in authoritative answer 28482 queries resulted in non authoritative answer 7 queries resulted in referral answer 591 queries resulted in nxrrset 53 queries resulted in SERVFAIL 2081 queries resulted in NXDOMAIN 14530 queries caused recursion 162 duplicate queries received 55 requested transfers completed ++ Zone Maintenance Statistics ++ 109536 IPv4 notifies sent ++ Resolver Statistics ++ [Common] [View: internal] 29362 IPv4 queries sent 2013 IPv6 queries sent 28531 IPv4 responses received 4209 NXDOMAIN received 6 SERVFAIL received 31 FORMERR received 32 EDNS(0) query failures 3359 query retries 836 query timeouts 5348 IPv4 NS address fetches 3271 IPv6 NS address fetches 83 IPv4 NS address fetch failed 2779 IPv6 NS address fetch failed 17421 DNSSEC validation attempted 12731 DNSSEC validation succeeded 4690 DNSSEC NX validation succeeded 21104 queries with RTT 10-100ms 7418 queries with RTT 100-500ms 3 queries with RTT 500-800ms 1 queries with RTT 800-1600ms [View: external] 192 IPv4 queries sent 104 IPv6 queries sent 192 IPv4 responses received 2 NXDOMAIN received 104 query retries 44 IPv4 NS address fetches 44 IPv6 NS address fetches 1 IPv4 NS address fetch failed 1 IPv6 NS address fetch failed 4 DNSSEC validation attempted 3 DNSSEC validation succeeded 1 DNSSEC NX validation succeeded 152 queries with RTT 10-100ms 40 queries with RTT 100-500ms [View: _bind] ++ Cache DB RRsets ++ [View: internal (Cache: internal)] 2007 A 652 NS 131 CNAME 1 MX 32 TXT 421 AAAA 28 DS 244 RRSIG 110 NSEC 3 DNSKEY 2 !A 2 !TXT 89 !AAAA 2 !SPF 14 !DLV 148 NXDOMAIN [View: external (Cache: external)] 55 A 12 NS 34 AAAA 2 DS 10 RRSIG 1 DNSKEY [View: _bind (Cache: _bind)] ++ Socket I/O Statistics ++ 82958 UDP/IPv4 sockets opened 2118 UDP/IPv6 sockets opened 4 TCP/IPv4 sockets opened 1 TCP/IPv6 sockets opened 82956 UDP/IPv4 sockets closed 2117 UDP/IPv6 sockets closed 58 TCP/IPv4 sockets closed 15 UDP/IPv4 socket bind failures 2117 UDP/IPv6 socket connect failures 29554 UDP/IPv4 connections established 59 TCP/IPv4 connections accepted 2117 UDP/IPv6 send errors 5 UDP/IPv4 recv errors ++ Per Zone Query Statistics ++ --- Statistics Dump --- (1352931389)

  Read the article

• USB mouse disconnecting and reconnecting randomly and often

  - by Marc

  Specs: Q6600, evga 780I sli mobo, 4gig RAM, logitech MX518, windows 7 64bit, evga gtx 260, 650W power supply (single rail) The problem I am having is my mouse will reconnect/disconnect (will even hear the sounds from windows) and the light on the bottom of the mouse will turn off/turn on as it starts working again. It really sucks to be playing a game (and happens on desktop as well) for the mouse to just die out for a few seconds and come back. Sometimes it will not happen for days and other times it will do it 2 or more times within 15 seconds. I have tried two different wired mice, have tried multiple USB ports (on front of computer, back of computer, have also used a USB hub and have also plugged in a card that connects to the USB connectors on the motherboard and adds a few usb ports to the back of the computer, and I also bought a USB 2.0 PCI card and that did not help). Nothing else seems to reconnect like this, my usb keyboard has never once cut out like the mouse does and neither have any of the other devices I have connected (webcam, usb hub, various devices sometimes connected through usb cables, and IR reciever for windows media center remote). I have disconnected all usb devices except for my keyboard and mouse and the problem still occurs. I guess it could be something wrong with my motherboard but since no other devices behave similarly I'm just hoping that it is some kind of driver conflict. Installing logitech's drivers has had no effect. It seemed at first that if I go to device manager and uninstall HID-compliant mouse (that and logitech mx518 are listed) that would fix it but it doesn't seem to work anymore or at least not every time (it keeps reinstalling). I have googled "usb mouse disconnects and reconnects" and it seems to be fairly common but none of those were resolved. To stick some easy steps: It happens with or without the drivers installed It has happened with multiple mice on the same computer Bios is the latest version (P08) Motherboard drivers are the latest version Device manager is listing no problems on any USB devices Happens with every usb port, even addon usb cards Happens when all usb devices aside from mouse and keyboard are unplugged I read that maybe it is an IRQ conflict and I tried to look into that but did not really know what was going on, but didn't see anything obviously wrong. Thanks for any help guys, its driving me crazy!

  Read the article

• NTPD issue - syncs then slowly loses ground

  - by ethrbunny

  RHEL 5 workstation. Has been running smoothly for years. I did a 'pup' recently and followed with a nice, cleansing reboot. Afterwards the system had some startup issues: namely MySQL refused to start. It just went "...." for 5-10 minutes before I did another boot and skipped that step (using 'interactive'). This was the only service that didn't wan't to start normally. So now that the system is booted I've found that it doesn't want to stay in sync with the NTP master and after 48 hours is refusing any SSH other than root. NTPD: this service starts normally and gets a lock on 4 servers. Almost immediately it starts to lose ground and now (after 3 days) is almost 40 hours behind. If I stop/start the service it gets the lock, resets the system clock and starts losing ground again. The 'hwclock' is set properly and maintains its time. Login: when I (re)start the ntp server I am able to login normally. I assume this problem is due to losing sync with LDAP. This appears to be verified by LDAP errors in /var/log/messages. Suggestions on where to look? ADDENDA: Tried deleting the 'drift' file. After a bit it gets recreated with 0.000. from /var/log/messages: Jan 17 06:54:01 aeolus ntpdate[5084]: step time server 129.95.96.10 offset 30.139216 sec Jan 17 06:54:01 aeolus ntpd[5086]: ntpd [email protected] Tue Oct 25 12:54:17 UTC 2011 (1) Jan 17 06:54:01 aeolus ntpd[5087]: precision = 1.000 usec Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, 0.0.0.0#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, ::#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, ::1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, fe80::213:72ff:fe20:4080#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, 127.0.0.1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, 10.127.24.81#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: kernel time sync status 0040 Jan 17 06:54:02 aeolus ntpd[5087]: frequency initialized 0.000 PPM from /var/lib/ntp/drift Jan 17 06:54:02 aeolus ntpd[5087]: system event 'event_restart' (0x01) status 'sync_alarm, sync_unspec, 1 event, event_unspec' (0xc010) You can see the 30 second offset. This was after about one minute of operation.

  Read the article

• Suggestions for sharing and using data between Ubuntu and Windows 7 dual boot

  - by wizjany

  Note: TL;DR, scroll to bottom for summary. I recently set up my computer for a dual boot between Ubuntu 9.10 and Windows 7. My current drive setup is as follows. | A1 | A2 | | B1 | B2 | B3 | A1: 100 mb, windows 7 "System Reserved" boot partition A2: 230 gb, data section, this one needs to be shared between the operating systems B1: 125 gb, windows 7 OS B2: 123 gb, ubuntu OS B3: 2gb, linux swap space Pretty much i want to have my documents, music, pictures, videos, etc accessible from both operating systems. My first attempt involved making the data (a2) partition NTFS, and moving my home folder from ubuntu to the data partition. However, as I read NTFS does not work nice with permission, and it messed up my home folder. My next idea is one of the following: 1) format the data partition to ext2/3/4 and move my home folder from linux there, and get a driver to read ext partitions in windows 7. The problem with that is that most of the ext drivers/software are not compatible with windows 7 or do not integrate with windows explorer (I really don't want to open a separate software window just to access my data, plus it's probably not compatible with other software.) http://www.fs-driver.org/ looks promising, but I'm not sure how it works with ext4 and windows 7 (not officially supported, when trying in vista compatibility mode, it tells me I need to format the ext drive to use it). My next idea, 2) keep the home folder in ubuntu where it is, but create symlinks for the Documents, Music, etc folders to an NTFS formatted Data (A2) partition, and add those locations to the windows 7 libraries. I'm not totally sure how the permissions would work out, but it should be fine since it's only the documents, music, etc and not the important config files in the rest of /home/user/. Correct me if I'm wrong. Currently, symlinks is my best idea, although i'm not sure how it will work. Any suggestions, additions to my ideas, links, pointers, whatever would be greatly appreciated. Even if it means i should reformat both my drives and repartition (2 250gb drives if you want to suggest a setup for that), I won't be too opposed if that's the best suggestion (I've gone through the format/install/format/reinstall process 5 times over the past 3 days, once more won't hurt me). TL;DR, summary: I have two hard drives. One is partitioned for Ubuntu and Windows 7, the second one I want accessible to both operating systems to store documents, music, pictures, videos, etc. Suggestions on how to set up the data drive please =) P.S. bonus if I can get an apache server document root folder working between the two OS's as well (permissions could become very complicated, so don't worry too much about that) P.P.S. Related question, but data viewing is one way: http://superuser.com/questions/84586/partition-scheme-and-size-for-dual-boot-windows-7-and-ubuntu-9-10-with-separate-p

  Read the article

• Can't get Apache 2.2.21 to compile with OpenSSL support

  - by angstwad

  Alright -- having a bad couple days here compiling Apache 2.2.21 on CentOS 5.7 with the following configure commands: ./configure --enable-ssl=shared --with-ssl=/usr/local/openssl I've compiled from source OpenSSL 1.0.0e from source: ./config --prefix=/usr/local --openssldir=/usr/local/openssl shared zlib-dynamic I attempt to start Apache and it returns: httpd: Syntax error on line 54 of /usr/local/apache2/conf/httpd.conf: Cannot load /usr/local/apache2/modules/mod_ssl.so into server: /usr/local/apache2/modules/mod_ssl.so: undefined symbol: SSL_get_servername If I look at how the libraries are linked, this is what I get: [root@web1 modules]# ldd mod_ssl.so libssl.so.6 => /lib64/libssl.so.6 (0x00002aaaaace4000) libcrypto.so.6 => /lib64/libcrypto.so.6 (0x00002aaaaaf30000) libdl.so.2 => /lib64/libdl.so.2 (0x00002aaaab281000) libz.so.1 => /lib64/libz.so.1 (0x00002aaaab486000) libpthread.so.0 => /lib64/libpthread.so.0 (0x00002aaaab69a000) libc.so.6 => /lib64/libc.so.6 (0x00002aaaab8b5000) libgssapi_krb5.so.2 => /usr/lib64/libgssapi_krb5.so.2 (0x00002aaaabc0e000) libkrb5.so.3 => /usr/lib64/libkrb5.so.3 (0x00002aaaabe3c000) libcom_err.so.2 => /lib64/libcom_err.so.2 (0x00002aaaac0d1000) libk5crypto.so.3 => /usr/lib64/libk5crypto.so.3 (0x00002aaaac2d4000) /lib64/ld-linux-x86-64.so.2 (0x0000555555554000) libkrb5support.so.0 => /usr/lib64/libkrb5support.so.0 (0x00002aaaac4f9000) libkeyutils.so.1 => /lib64/libkeyutils.so.1 (0x00002aaaac702000) libresolv.so.2 => /lib64/libresolv.so.2 (0x00002aaaac904000) libselinux.so.1 => /lib64/libselinux.so.1 (0x00002aaaacb19000) libsepol.so.1 => /lib64/libsepol.so.1 (0x00002aaaacd32000) Basically, I've tired compiling from source OpenSSL (both 0.9.8r and 1e), having yum reinstall from the repos, done a make clean and remade both OpenSSL and Apache numerous times -- but I can't get it to compile into the apache base or dynamically as a shared object file. What am I doing wrong here? Update 1: After doing a make clean and make distclean, I've reconfigured with the same parameters as above without any effect. The config.log is at Pastebin. Update 2: Modifying the LD_LIBRARY_PATH had no effect on the lib-deps of mod_ssl.so. UPDATE 3: I've compiled and recompiled many times, and verified with ldconfig that the OpenSSL libs dir is in my path, and included in ld.so.conf. Still cannot get httpd/mod_ssl to load the library at runtime.

  Read the article

• WinXP - Having trouble sharing internet with 3G USB modem via ICS

  - by Carlos Nunez

  all! I've been banging my head against a wall with this issue for a few days now and am hoping someone can help out. I recently signed up for T-Mobile's webConnect 3G/4G service to replace the faltering (and slow) DSL connection in my apartment. The goal was to put the SIM in one of my old phones and use its built-in WLAN tethering feature to share Internet out to rest of my computers. I quickly found out that webConnect-provisioned SIMs do not work with regular smartphones, so I was forced to either buy a 4G-compatible router or tether one of my old laptops to my wireless router and share out that way. I chose the latter, and it's sharpening my inner masochistic self by the day. Here's the setup: GSM USB modem (via hub), ICS host - 10/100 Mbps Ethernet NIC, ICS "guest" - WAN port of my SMC WGBR14N wireless router in bridged mode (i.e. wireless access point). Ideally, this would make my laptop the DHCP server and internet gateway with the WAP giving everyone wireless coverage. I can browse internet on the host laptop fine. However, when clients try to connect, they get a DHCP-assigned IP from the laptop and are able to use the Internet for a few minutes before completely dying. After that happens, they are able to re-associate with the WAP and get IP addresses, but are unable to use Internet or resolve IP addresses until the laptop and router are restarted. If they do get access, it's very, very slow. After running Wireshark on the host machine, it turns out that this is because every TCP connection keeps getting RST. DNS seems to work. I would normally think the firewall is the culprit here, but when it drops packets, it drops them completely. The fact that TCP connections are being ACK'ed by the destination rules that out. Of course, none of the event Log isn't saying anything about what's going on. I also tried disabling power management on the NIC, since that's caused problems in the past; that didn't help either. I finally disabled receive-side scaling as per a Microsoft KB (that applied to Windows Server 2003, SP2) to no avail. I'm thinking of trying it with a different NIC (will be tough; don't have a spare Ethernet NIC around for the laptop), but I'm getting the impression that this simply doesn't work. Can anyone please advise? I apologise for the length of this post; all contributions are much appreciated! -Carlos.

  Read the article

• Safer RAID5 rebuilds using partially failed disks?

  - by arcticmac

  There have been lots of articles posted recently about how RAID5 is dangerous because of long resilver times, and in particular because of increasing chances of encountering a URE during the resilver. Obviously this is a significant concern. However, it seems that in many cases of interest (as long as you're keeping some kind of eye on your disks), when it comes time to rebuild the array, the disk that I'm replacing is still mostly readable. If you try to explain this predicament to the average layperson, they are typically very confused as to why you have two almost completely functional disks but can't produce one working array. It seems to me that there ought to be some way to take advantage of this to make rebuilds safer, as long as I'm willing to have the RAID5 be read-only for a couple of days while it rebuilds. Conceptually, what I have in mind looks something like this: When a disk fails, immediately take the RAID5 offline or mount it read-only Attach a new disk (either in a spare bay, or externally via eSATA) and begin rebuilding it to replace the failed one. If known, perhaps start with the stripes in which the failure occurred, to minimize the chances of losing those if another disk fails. In the event that a second disk experiences a URE or other failure during the rebuild, try to source that data from the disk that is being replaced. Presumably if this happens, more rebuilding would be necessary. When complete, shut down the server, swap the replacement drive into the original bay if desired, and bring the array back up. Obviously such a process would not be appropriate for applications where uptime is critical or data loss cannot be tolerated, but it seems to me that this could help considerably to improve the reliability of RAID5. I assume that there's not a good way to implement a recovery like this at present, given that I haven't seen any indication of tools that are designed to do this, and that it seems like it would be rather obtuse to work out manually. Are there also technical issues with it that I haven't thought of (I'm still fairly new to RAID stuff)? Any thoughts on how hard something like this would be to implement (e.g. in linux md raid)?

  Read the article

• Mikrotik and NAT/Routing issue

  - by arul

  I have basic NAT/Routing problem with Mikrotik RB750 that I've been unable to solve over the past days. From our ISP we have 26 IP addresses: 10.10.10.192/27, with 10.10.10.193 being the gateway and 10.10.10.194 the first available IP. What I need is that everything connected to ether2 gets a public IP from the DHCP server, and everything connected to ether3 gets a local IP from another DHCP (192.168.100.0/24). All clients should have internet access (I'll figure out bandwidth throttling later) and optimally just 'see' each other (all boxes are Win7, I guess this can ultimately be handled with VPN). Here is my setup: ether1 (10.10.10.194) is connected directly to ISP. 20 clients connected to ether2(10.10.10.195), and another 20 to ether3(10.10.10.196) (both through same 24 port switches). This is my setup, which doesn't work, all 20 clients from ether2 can access the internet, though all comm. seems to come from 10.10.10.194 (is this due to the masquerade on ether1?), and ether3 can't access the internet at all. I think that I need to masquerade ether3, and SNAT/DNAT or NETMAP ether2, but that doesn't work either, I guess that I need to somehow 'wire' both ether2+3 to ether1. Address list: # ADDRESS NETWORK INTERFACE 0 ;;; public 10.10.10.194/32 10.10.10.192 ether1-gateway 1 ;;; inner DHCP 192.168.100.0/24 192.168.100.0 ether3-private 2 ;;; public 10.10.10.195/32 10.10.10.192 ether2-pub 3 ;;; public 10.10.10.196/32 10.10.10.192 ether3-private NAT 0 ;;; ether3 nat chain=srcnat action=src-nat to-addresses=10.10.10.196 src-address=192.168.100.0/24 out-interface=ether3-private 1 ;;; ether3 nat chain=dstnat action=dst-nat to-addresses=192.168.100.0/24 in-interface=ether3-private 2 ;;; ether1 masquerade chain=srcnat action=masquerade to-addresses=10.10.10.194 out-interface=ether1-gateway Routes: # DST-ADDRESS PREF-SRC GATEWAY DISTANCE 0 A S 0.0.0.0/0 ether1-gateway 1 2 A S 10.10.10.192/27 10.10.10.195 ether2-pub 1 3 ADC 10.10.10.192/32 10.10.10.195 ether2-pub 0 ether1-gateway ether3-private 4 ADC 192.168.100.0/24 192.168.100.0 ether3-private 0 IP Pools: # NAME RANGES 0 public-pool 10.10.10.201-10.10.10.220 1 private-pool 192.168.100.2-192.168.100.254 DHCP configs: # NAME INTERFACE RELAY ADDRESS-POOL LEASE-TIME ADD-ARP 0 public-dhcp ether2-pub public-pool 3d 1 private-dhcp ether3-private private-pool 3d Thanks!

  Read the article

• Apache and MySQL taking all the memory? Maximum connections?

  - by lpfavreau

  I've a had one of our servers going down (network wise) but keeping its uptime (so looks the server is not losing its power) recently. I've asked my hosting company to investigate and I've been told, after investigation, that Apache and MySQL were at all time using 80% of the memory and peaking at 95% and that I might be needing to add some more RAM to the server. One of their justifications to adding more RAM was that I was using the default max connections setting (125 for MySQL and 150 for Apache) and that for handling those 150 simultaneous connections, I would need at least 3Gb of memory instead of the 1Gb I have at the moment. Now, I understand that tweaking the max connections might be better than me leaving the default setting although I didn't feel it was a concern at the moment, having had servers with the same configuration handle more traffic than the current 1 or 2 visitors before the lunch, telling myself I'd tweak it depending on the visits pattern later. I've also always known Apache was more memory hungry under default settings than its competitor such as nginx and lighttpd. Nonetheless, looking at the stats of my machine, I'm trying to see how my hosting company got those numbers. I'm getting: # free -m total used free shared buffers cached Mem: 1000 944 56 0 148 725 -/+ buffers/cache: 71 929 Swap: 1953 0 1953 Which I guess means that yes, the server is reserving around 95% of its memory at the moment but I also thought it meant that only 71 out of the 1000 total were really used by the applications at the moment looking a the buffers/cache row. Also I don't see any swapping: # vmstat 60 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 57612 151704 742596 0 0 1 1 3 11 0 0 100 0 0 0 0 57604 151704 742596 0 0 0 1 1 24 0 0 100 0 0 0 0 57604 151704 742596 0 0 0 2 1 18 0 0 100 0 0 0 0 57604 151704 742596 0 0 0 0 1 13 0 0 100 0 And finally, while requesting a page: top - 08:33:19 up 3 days, 13:11, 2 users, load average: 0.06, 0.02, 0.00 Tasks: 81 total, 1 running, 80 sleeping, 0 stopped, 0 zombie Cpu(s): 1.3%us, 0.3%sy, 0.0%ni, 98.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1024616k total, 976744k used, 47872k free, 151716k buffers Swap: 2000052k total, 0k used, 2000052k free, 742596k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 24914 www-data 20 0 26296 8640 3724 S 2 0.8 0:00.06 apache2 23785 mysql 20 0 125m 18m 5268 S 1 1.9 0:04.54 mysqld 24491 www-data 20 0 25828 7488 3180 S 1 0.7 0:00.02 apache2 1 root 20 0 2844 1688 544 S 0 0.2 0:01.30 init ... So, I'd like to know, experts of serverfault: Do I really need more RAM at the moment? How do they calculate that for 150 simultaneous connections I'd need 3Gb? Thanks for your help!

  Read the article

• Amusing or Sad? Network Solutions

  - by dbasnett

  When I got sick my email ended up in every drug sellers email list. Some days I get over 200 emails selling everything from Viagra to Xanax. Either they don't know what my condition is or they are telling me you are a goner, might as well chill-ax and have a good time. In order to cut down on the mail being downloaded I thought I would add all of the Junk email senders from Outlook to my Network Solution mail server. Much to my amazement I could not find that import Spammers button, so I submitted a tech support request. Here is the response: Thank you for contacting Network Solutions Customer Service Department. We are committed to creating the best Customer experience possible. One of the first ways we can demonstrate our commitment to this goal is to quickly and efficiently handle your recent request. We apologize for any inconvenience this might have caused you. With regard to your concern, please be advised that we cannot import blocked senders in to you e-mail servers. An alternative option is for you to create a Custom Filter that filters unwanted e-mails. To create a Custom Filter: Open a Web browser (e.g., Netscape, Microsoft Internet Explorer, etc.). Type mail.[domain name].[ext] in the address line. Login to your Network Solutions email account. Click on the Configuration left menu tab. Click on the Custom Filter link. Type the rule name. blah, blah, blah Basically add them one at a time. "We are committed to creating the best Customer experience possible." No you are not. You are trying to squeeze every nickle you can out of me. "With regard to your concern, please be advised that we cannot import blocked senders in to you e-mail servers." Maybe I should apply for a job to write those ten complicated lines of code... Maybe I should question my choice of vendors, because if they truly "cannot" then they are to stupid to have my business. It is both amusing and sad. I'll be posting this in every forum I am a member of.

  Read the article

• Fedora 13 post security update boot problem

  - by Alex

  Hello. About a month ago I installed a security update that had new Kernek 2.6.34.x from 2.6.33.x), this is when the problem occurred for the first time. After the install my computer would not boot at all, black screen without any visible hard drive activity (I gave it good 30 minutes on black screen, before took actions)... I poped in installation DVD and went in rescue mode to change back the boot option to old kernel (was just a guess where the problem was). After restart computer loaded just file, took a long time for it to start because of SELinux targeted policy relabel is required. Relabeling could take very long time depending on file size. I assumed that the update got messed up somehow and continued working with modified boot option. Couple of days ago, there was another kernel update. I installed it and same problem as before. This rules out corrupted update theory... Black screen right after 'BIOS' screen before OS gets loaded. I had to rescue system again... Below is copy of my grub.conf file. I am fairly new to LINUX (couple of years of experience), mostly development and basic config... nothing crazy. # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/vg_obalyuk-lv_root # initrd /initrd-[generic-]version.img #boot=/dev/sda default=2 timeout=0 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title Fedora (2.6.34.6-54.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.34.6-54.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.34.6-54.fc13.i686.PAE.img title Fedora (2.6.34.6-47.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.34.6-47.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.34.6-47.fc13.i686.PAE.img title Fedora (2.6.33.8-149.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.33.8-149.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.33.8-149.fc13.i686.PAE.img I like my system to be up to date... Let me know if I can post any other files that can be of help. Has anyone else had this problem? Does anyone has any ideas how to fix this problem? p.s. Anything helps, you ppl are great! thx for ur time.

  Read the article

< Previous Page | 274 275 276 277 278 279 280 281 282 283 284 285  | Next Page >