Search Results

Search found 29064 results on 1163 pages for 'network management'.

Page 279/1163 | < Previous Page | 275 276 277 278 279 280 281 282 283 284 285 286  | Next Page >

• How do I protect a low budget network from rogue DHCP servers?

  - by Kenned

  I am helping a friend manage a shared internet connection in an apartment buildling with 80 apartments - 8 stairways with 10 apartments in each. The network is laid out with the internet router at one end of the building, connected to a cheap non-managed 16 port switch in the first stairway where the first 10 apartments are also connected. One port is connected to another 16 port cheapo switch in the next stairway, where those 10 apartments are connected, and so forth. Sort of a daisy chain of switches, with 10 apartments as spokes on each "daisy". The building is a U-shape, approximately 50 x 50 meters, 20 meters high - so from the router to the farthest apartment it’s probably around 200 meters including up-and-down stairways. We have a fair bit of problems with people hooking up wifi-routers the wrong way, creating rogue DHCP servers which interrupt large groups of the users and we wish to solve this problem by making the network smarter (instead of doing a physical unplugging binary search). With my limited networking skills, I see two ways - DHCP-snooping or splitting the entire network into separate VLANS for each apartment. Separate VLANS gives each apartment their own private connection to the router, while DHCP snooping will still allow LAN gaming and file sharing. Will DHCP snooping work with this kind of network topology, or does that rely on the network being in a proper hub-and-spoke-configuration? I am not sure if there are different levels of DHCP snooping - say like expensive Cisco switches will do anything, but inexpensive ones like TP-Link, D-Link or Netgear will only do it in certain topologies? And will basic VLAN support be good enough for this topology? I guess even cheap managed switches can tag traffic from each port with it’s own VLAN tag, but when the next switch in the daisy chain receives the packet on it’s “downlink” port, wouldn’t it strip or replace the VLAN tag with it’s own trunk-tag (or whatever the name is for the backbone traffic). Money is tight, and I don’t think we can afford professional grade Cisco (I have been campaigning for this for years), so I’d love some advice on which solution has the best support on low-end network equipment and if there are some specific models that are recommended? For instance low-end HP switches or even budget brands like TP-Link, D-Link etc. If I have overlooked another way to solve this problem it is due to my lack of knowledge. :)

  Read the article

• Certain SFTP user cannot connect

  - by trobrock

  I have my Ubuntu Server set up so users with the group of sftponly can connect with sftp, but have a shell of /bin/false, and they connect to their home directories. This is working fine with three of the user accounts I have. But I added a new user account today the same way that I added the others and it will not successfully connect. sftp -vvv user@hostname debug1: Next authentication method: password user@hostname's password: debug3: packet_send2: adding 48 (len 73 padlen 7 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). debug2: fd 5 setting O_NONBLOCK debug3: fd 6 is O_NONBLOCK debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug1: channel 0: free: client-session, nchannels 1 debug3: channel 0: status: The following connections are open: #0 client-session (t3 r-1 i0/0 o0/0 fd 5/6 cfd -1) debug3: channel 0: close_fds r 5 w 6 e 7 c -1 debug1: fd 0 clearing O_NONBLOCK debug3: fd 1 is not O_NONBLOCK Connection to hostname closed by remote host. Transferred: sent 2176, received 1848 bytes, in 0.0 seconds Bytes per second: sent 127453.3, received 108241.6 debug1: Exit status -1 Connection closed For a successful user: sftp -vvv good_user@hostname debug1: Next authentication method: password good_user@hostname's password: debug3: packet_send2: adding 48 (len 63 padlen 17 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). debug2: fd 5 setting O_NONBLOCK debug3: fd 6 is O_NONBLOCK debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug1: Sending subsystem: sftp debug2: channel 0: request subsystem confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: subsystem request accepted on channel 0 debug2: Remote version: 3 debug2: Server supports extension "[email protected]" revision 1 debug2: Server supports extension "[email protected]" revision 2 debug2: Server supports extension "[email protected]" revision 2 debug3: Sent message fd 3 T:16 I:1 debug3: SSH_FXP_REALPATH . -> / sftp> I cannot figure out why one user will work and the other wont, I have restart the ssh service after adding the user. I have even removed the user and added them again to be sure I am adding it correctly.

  Read the article

• Which Online Notepad to use?

  - by user1413

  What is the best online notepad? I once used Google Notebook but Google no longer supports it and I don't want to put my stuff on an unsupported site. I now use Luminotes but I find editing of the text to be infuriating. What is better?

  Read the article

• Why does a wired network slow down with user increase?

  - by Ed Briscoe

  If you had a wired network, 20 PCs hooked up to a 100 Mbit/sec switch (same onboard ethernet port speed) and you were just sending some test data round. What is the technical explanation as to why 20 machines sending test data around this network to each other is slower than one to one? I mean I know a busy network means it's slower but I'm really trying to understand some more technical details. Thanks for any help

  Read the article

• How to get httrack to work with SSL on mac os x? (libssl.so not found)

  - by cwd

  I'm trying to use httrack website copier but the program is running and reporting "no-ssl" (ie: it does not have the capability to copy secure sites). From looking over this thread, it seems that the problem is either when I make & configure the program, or when I run the program, it is not finding the lib-ssl / open-ssl that I have installed. I think it is looking for /var/root/lib/libssl.so.1.0 The user on that forum states that he created a symlink which allowed httrack to find the ssl library in the non-default location. Perhaps that's what I need to do - but where do I create the link from and to? I'm not seeing that I have any libssl.so files installed on my system. Do I need the development package? If so, how do I install that? I used macports to install the current version of openssl that I have. I'm running OS X 10.6. Reserch I have run this command to try and debug: dtruss httrack 2&1 | grep ssl and that outputs this: stat64("libssl.so.1.0\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.1.0\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.1.0\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.1.0\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.1\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.1\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.1\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.1\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.1.0.0\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.1.0.0\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.1.0.0\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.1.0.0\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.8p\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.8p\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.8p\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.8p\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.8o\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.8o\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.8o\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.8o\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.8n\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.8n\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.8n\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.8n\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.8m\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.8m\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.8m\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.8m\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.8l\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.8l\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.8l\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.8l\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.8k\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.8k\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.8k\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.8k\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.8j\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.8j\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.8j\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.8j\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.8g\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.8g\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.8g\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.8g\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.8b\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.8b\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.8b\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.8b\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.8\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.8\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.8\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.8\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.7\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.7\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.7\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.7\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so.0.9.6\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so.0.9.6\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so.0.9.6\0", 0x7FFF5FBFF210, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so.0.9.6\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("libssl.so\0", 0x7FFF5FBFEE30, 0x7FFF5FBFF470) = -1 Err#2 stat64("/var/root/lib/libssl.so\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/local/lib/libssl.so\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 stat64("/usr/lib/libssl.so\0", 0x7FFF5FBFF220, 0x7FFF5FBFF470) = -1 Err#2 I have already used mac ports to install open-ssl: port installed The following ports are currently installed: beecrypt @4.2.1_2 (active) cpio @2.10_0 (active) expat @2.0.1_1 (active) flex @2.5.35_0 (active) gettext @0.18.1.1_2 (active) gperf @3.0.4_0 (active) icu @4.6_0 (active) libiconv @1.13.1_0 (active) mysql5 @5.1.53_0 (active) ncurses @5.9_0 (active) ncursesw @5.8_0 (active) neon @0.29.5_0 (active) openssl @1.0.0c_0 (active) perl5.8 @5.8.9_3 (active) popt @1.16_0 (active) python24 @2.4.6_7 (active) readline @6.1.002_0 (active) rpm @4.4.9_10 (active) sqlite3 @3.7.3_0 (active) zlib @1.2.5_0 (active) Here are the install locations: locate libssl /opt/local/lib/libssl.1.0.0.dylib /opt/local/lib/libssl.a /opt/local/lib/libssl.dylib /opt/local/lib/pkgconfig/libssl.pc /opt/local/var/macports/software/openssl/1.0.0c_0/opt/local/lib/libssl.1.0.0.dylib /opt/local/var/macports/software/openssl/1.0.0c_0/opt/local/lib/libssl.a /opt/local/var/macports/software/openssl/1.0.0c_0/opt/local/lib/libssl.dylib /opt/local/var/macports/software/openssl/1.0.0c_0/opt/local/lib/pkgconfig/libssl.pc /usr/lib/libssl.0.9.7.dylib /usr/lib/libssl.0.9.8.dylib /usr/lib/libssl.0.9.dylib /usr/lib/libssl.dylib /usr/lib/pkgconfig/libssl.pc What should I do next? More Info I tried the solution below: $ DYLD_INSERT_LIBRARIES="/opt/local/lib/libssl.1.0.0.dylib" httrack Welcome to HTTrack Website Copier (Offline Browser) 3.44-1-nossl Copyright (C) Xavier Roche and other contributors To see the option list, enter a blank line or try httrack --help It is still not able to load the ssl lib: 3.44-1-nossl

  Read the article

• Given a debian source package - How do I install the build-deps?

  - by Rory McCann

  I have a debian (well technically ubuntu) source package, i.e. the .dsc, the .tar.gz, etc., I want to build this. The dpkg-buildpackage fails, since I don't have all the build dependencies. Normally I'd use apt-get build-dep, but this package isn't in apt. Is there a 'clean', 'proper' way to install all the build dependencies, given a source package. I know I could just open the debian/control file, but I'm curious if there's a 'proper' way.

  Read the article

• Windows File System Analysis

  - by bouvierr

  I am looking for a FREE tool to perform analyses on the NTFS file system of my Windows 7 PC. I want to easily see the amount of data distributed throught out the entire file system. The following applications seem very good, but they are not free and probably overkill for my requirements: FolderSizes 5 MailMeter Windows File System Reporting Tool I am aware that some applications (like Folder Size 2.5) can add a column in Windows Explorer to show the size of each folder, but I am looking for something more like a reporting tool. Thank you for your suggestions.

  Read the article

• Debian Simple Gui for adding/removing users for protective directories

  - by ErocM

  We have a hosted site with a directory that is password protected. I need to have a user who knows very little about computers, maintain the users that have access to this directory. The list is going to get big, according to our customer database. My question is 2 fold: Is there a simple gui program that I can have this user utilize to be able to maintain the users without having to teach them how to use ssh and UNIX? Am I going about this the right way? Is there a better way to do this? Thanks for your help!

  Read the article

• Linux: Managing users, groups and applications

  - by RN

  I am fairly new to linux admin so this may sound quite a noob question. I have a VPS account with a root access I need to install Tomcat, Java on it and later other open source applications as well. Installation for all of these is as simple as unzipping the .gz in a folder. My questions are A) Where should I keep all these programs? In Windows, I typically have a folder called programs under c:\ where I unzip all applications. I plan to have something similar here as well. Currently, I have all these under apps folder under/root- which I am guessing is a bad idea B) To what group should Tom belong to ? I would need a user - say Tom who can simply execute these programs. Do I need to create a new group? or just add Tom to some existing group ? C) Finally- Am I doing something really stupid by installing all these application by simply unzipping them? I mean an alternate way would be to use Yup or RPM or something like that to install these applications. Given my familiarity and (tight budget) that seems too much to me. I feel uncomfortable running commands which i don't understand too well

  Read the article

• Can Debian identify rarely used packages?

  - by Norman Ramsey

  I'd like to find a tool that could tell me which Debian packages on my system have been rarely or never used, perhaps by looking at file lists and access times. This is to find candidates for deletion from my nearly full hard drive. I'm not very well informed about the rich ecosystem of desktop GUI tools (I use aptitude); does anyone know if one of those tools, or any other tool, can identify how recently a package has been used?

  Read the article

• How to detect APC UPS battery usage and run a script when on battery

  - by Andy Arismendi

  I have a couple APC UPS - Smart-UPS RT 6000 RM XL Smart-UPS RT 5000 RM XL Unfortunately the power in my office likes to go out (out of my control) and hence the equipment powered by these UPS shuts down. They power a VMware infrastructure environment (VMware Lab Manager) and what I'd like to do is detect when one is on battery (say has been for x amount of time or has x percentage left) and run a script on this event. What software do I need to detect a on-battery event and have it run a script? Thanks!

  Read the article

• Open source alternatives for quickbooks?

  - by fragsworth

  Not much else to ask about this. I'd like something that runs in linux. Any suggestions?

  Read the article

• Esx servers in a DMZ

  - by James

  I have two ESX 3.5 servers in a DMZ. I can access these servers on any port from my lan via a VPN. Servers in the DMZ are unable to initiate connections back to the lan, for obvious reasons. I have a vCenter server on my lan and can initially connect to the esx servers fine. However the esx servers then try to send a hearth beat back to the vCenter server on udp/902 obviously this will not get back to the vCenter server, which then marks the ESX servers as not responding and disconnects. There are two broad solutions I can think of; 1) Try to tell vCenter to ignore not getting heart beats. The best I can do here is delay the disconnect by 3 mins. 2) Try some clever network solution. However again I am at loss. Note: The vCenter server is on a lan, and cannot be given a public IP, so firewall rules back will not work. And also I cannot setup a VPN from the DMZ to the lan. **I am adding the following, explanation that I added to the comments Ok maybe this is the bit that I not explaining well. The DMZ is on a remote site, an entirely independent network (network 1). The vCenter server is on our office lan (network 2). Network 2 can connect to any machine on any port on network 1. But network 1 is not allowed to initiate a connection to network 2. Any traffic destined to network 2 from network 1 gets dropped by the firewall as it is traffic to a non-routable address. The only solution I can think of is setting up a VPN from network 1 to network 2, but this is not acceptable So any clever folk out there any ideas? J

  Read the article

• What are some fast methods for navigating to frequently used folders in Windows 7?

  - by fostandy

  (This is a followup question from my previous question.) In windows XP I used to be able to quickly navigate to frequently used folders by making use of the 'Favorites' menu item and the hotkey behaviour. In certain conditions it could be set up so that getting to a particular folder was as easy as alt-a x (and without a file explorer window open it was as fast as win-e alt-a x). I am struggling to get anywhere near this speed in Windows 7 and would like to solicit advice from others regarding fast folder navigation to see if I am missing any methods. My current way to navigate quickly is basically move hand to mouse move cursor to navigation pane/pain. scroll all the way to the top (because normally I the panel is focused on whatever deep directory structure I am already in). sift through my 50+ favorites to get the one I want, or click a link to a folder that contains further links in some sort of 'pseudo-tree' functionality. select it. This is slower than my previous method by upwards of an order of magnitude. There are a couple of things I've contemplated: add expandable folders, not just direct links, to the favorites menu. add expandable folders, not just direct links, to the start menu. add links of my favorite folders to a submenu of the start menu so that they come up when I search them. They do but this still rather cumbersome started using 7stacks - url here (I cannot link the url directly due to lack of reputation but http://www.alastria.com/index.php?p=software-7s). This is about the closest I've gotten to some sort of compact, customizeable, easy to access, tree based navigation structure. How do you power users quickly navigate to your favorite folders? Are there keyboard shortcuts I am missing? Can someone recommend other apps or addon or extensions that can achieve this sort of functionality? The Current solution (thanks to the answers below) I am going to use is a combination of Autohotkey and 7stacks - autohotkey to launch 7stacks, 7stacks with the 'menu' stack type for fast, key-enabled navigation to folders organised in a tree structure. This solves about 90% of the issue, the only issues are (note that these are really minor, I am really splitting hairs more than anything here) Can't use this for existing folder navigation (ie already have a explorer window open, want to go to another directory) A bit more cumbersome to add/remove entries to compared to xp favorites. A little slower than xp favorites. Whatever. I'm happy. Thanks guys. I think the answer is a split to John T and Kelbizzle - I've elected to give the answer to John T and +1 to Kelbizzle as I had already mentioned 7stacks.

  Read the article

• Converting dynamic to basic disk

  - by Josip Medved

  I converted basic disk to dynamic on my laptop. However, now I cannot install Windows 7 on another partition. I just get message that installing them on dynamic disk is not supported. Is there a way to convert dynamic disk to basic without losing data on already existing partition?

  Read the article

• Where are essential Windows files located?

  - by Dorothy

  I am using a Vista but I would like the answer for XP, Vista and Windows 7. I am writing a program where I want to count the Important or Essential files of the Windows PC. It looks like the Essential files would be located somewhere in C:/Windows and after some research I found that some Essential files are located in C:/Windows/winsxs. What and where are the Essential files for a Windows PC? Is there a folder or set of folders that contain the essential files? Are all the files in C:/Windows/winsxs Essential? Essential Definition: Absolutely necessary; extremely important

  Read the article

• System-install-packages missing in RedHat Enterprise Linux 5

  - by Kumar P

  i am using RedHat Enterprise Linux 5.1. When i use add-remove software in application menu, i think, that i wrongly uninstalled something. so after reboot that menu item missing. Also i can't use system-install-packages in terminal. When i double click rpm package it open as archive. And i specifically open it as software installer by open with other application, it saying error /usr/bin/system-install-packages missing. Help me to solve this problem ...

  Read the article

• Laptop wakes from sleep, once, due to audio controller (Windows 7)

  - by stijn

  The laptop is a recent Dell XPS 15z and the problem is as follows (reproducible about 90% of tries): put laptop to sleep using either Start-Sleep or closing the lid laptop goes to sleep after about 5 seconds, but instantly wakes again showing a black screen (touching the keyboard or moving the mouse shows the login screen one normally gets after wake) login again, put laptop to sleep latop stays in sleep mode output of powercfg -lastwake after the first instant wake shows the audio controller is responsible. Why would that be, why only the first try, and how to fix this? Wake History Count - 1 Wake History [0] Wake Source Count - 1 Wake Source [0] Type: Device Instance Path: PCI\VEN_8086&DEV_1C20&SUBSYS_04461028&REV_05\3&11583659&0&D8 Friendly Name: Description: High Definition Audio Controller Manufacturer: Microsoft

  Read the article

• Can I use a package manager of one distribution on another?

  - by Yktula

  I want to use Gentoo's packages on Fedora. Is this possible?

  Read the article

• SSH keys fail for one user

  - by Eli

  I just set up a new Debian server. I disabled root SSH and password auth, so you've gotta use a key file. For my primary user, everything works exactly as expected. I used ssh-keygen -t dsa and got myself a public and private key. Put one in authorized keys, put the other in a pem file locally. I wanted to create a user that I can deploy things with, so I did basically the same process. I addusered it, made a .ssh folder, ran ssh-keygen -t dsa (I also tried RSA), put the keys in their appropriate locations. No luck. I'm getting a Permission denied (publickey) error. When I use the exact same keys as the account that works, same error. When I enable password authentication, I can log in via SSH with the password. How do I debug this?

  Read the article

• How to manage configuration & automatic rollout of 20 virtual machines

  - by Lucas Meijer

  I have a TeamCity build server, with about 20 "build agents", both Windows and MacOS machines. Often, I need to install a newer version of XCode or VisualStudio or some other tool. Having to do this on all machines manually is boring and error prone. I'm trying to find out what is the best way to achieve the following: make it easy to change a system configuration, without having to do it on all machines manually. make it easy to add a new machine to the group. ensure the machines are as identical as possible The jobs these machines are executing is relatively heavy, fully consuming 8 cores, and be very heavy on IO. It's fine if the solution includes spending money.

  Read the article

• How could I stop ssh offering a wrong key?

  - by Alvaro Maceda

  (This is a problem with ssh, not gitolite) I've configured gitolite on my home server (ubuntu 12.04 server, open-ssh). I want an special identityfile to administer the repositories, so I need to access throught ssh to my own host ussing two different identity keys. This is the content of my .ssh/config file: Host gitadmin.gammu.com User git IdentityFile /home/alvaro/.ssh/id_gitolite_mantra Host git.gammu.com User git IdentityFile /home/alvaro/.ssh/id_alvaro_mantra This is the content of my hosts file: # Git 127.0.0.1 gitadmin.gammu.com 127.0.0.1 git.gammu.com So I should be able to communicate with gitolite this way to access with the "normal" account: $ssh git.gammu.com and this way to access with the administrative account: $ssh gitadmin.gammu.com When I try to access with the normal account, all is ok: alvaro@mantra:~/.ssh$ ssh git.gammu.com PTY allocation request failed on channel 0 hello alvaro, this is gitolite 2.2-1 (Debian) running on git 1.7.9.5 the gitolite config gives you the following access: @R_ @W_ testing Connection to git.gammu.com closed. When I do the same with the administrative account: alvaro@mantra:~$ ssh gitadmin.gammu.com PTY allocation request failed on channel 0 hello alvaro, this is gitolite 2.2-1 (Debian) running on git 1.7.9.5 the gitolite config gives you the following access: @R_ @W_ testing Connection to gitadmin.gammu.com closed. It should show the administrative repository. If I launch ssh with verbose option: ssh -vvv gitadmin.gammu.com ... debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/alvaro/.ssh/id_alvaro_mantra (0x7f7cb6c0fbc0) debug2: key: /home/alvaro/.ssh/id_gitolite_mantra (0x7f7cb6c044d0) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/alvaro/.ssh/id_alvaro_mantra debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-rsa blen 279 ... It's offering the key id_alvaro_mantra, and it should'nt!! The same happens when I specify the key with the -i option: ssh -i /home/alvaro/.ssh/id_gitolite_mantra -vvv gitadmin.gammu.com ... debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/alvaro/.ssh/id_alvaro_mantra (0x7fa365237f90) debug2: key: /home/alvaro/.ssh/id_gitolite_mantra (0x7fa365230550) debug2: key: /home/alvaro/.ssh/id_gitolite_mantra (0x7fa365231050) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/alvaro/.ssh/id_alvaro_mantra debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-rsa blen 279 debug2: input_userauth_pk_ok: fp 36:b1:43:36:af:4f:00:e5:e1:39:50:7e:07:80:14:26 debug3: sign_and_send_pubkey: RSA 36:b1:43:36:af:4f:00:e5:e1:39:50:7e:07:80:14:26 debug1: Authentication succeeded (publickey). ... What the hell is happening??? I'm missing something, but I can't find what. These are the contents of my home dir: -rw-rw-r-- 1 alvaro alvaro 395 nov 14 18:00 authorized_keys -rw-rw-r-- 1 alvaro alvaro 326 nov 21 10:21 config -rw------- 1 alvaro alvaro 137 nov 20 20:26 environment -rw------- 1 alvaro alvaro 1766 nov 20 21:41 id_alvaromaceda.es -rw-r--r-- 1 alvaro alvaro 404 nov 20 21:41 id_alvaromaceda.es.pub -rw------- 1 alvaro alvaro 1766 nov 14 17:59 id_alvaro_mantra -rw-r--r-- 1 alvaro alvaro 395 nov 14 17:59 id_alvaro_mantra.pub -rw------- 1 alvaro alvaro 771 nov 14 18:03 id_developer_mantra -rw------- 1 alvaro alvaro 1679 nov 20 12:37 id_dos_pruebasgit -rw-r--r-- 1 alvaro alvaro 395 nov 20 12:37 id_dos_pruebasgit.pub -rw------- 1 alvaro alvaro 1679 nov 20 12:46 id_gitolite_mantra -rw-r--r-- 1 alvaro alvaro 397 nov 20 12:46 id_gitolite_mantra.pub -rw------- 1 alvaro alvaro 1675 nov 20 21:44 id_gitpruebas.es -rw-r--r-- 1 alvaro alvaro 408 nov 20 21:44 id_gitpruebas.es.pub -rw------- 1 alvaro alvaro 1679 nov 20 12:34 id_uno_pruebasgit -rw-r--r-- 1 alvaro alvaro 395 nov 20 12:34 id_uno_pruebasgit.pub -rw-r--r-- 1 alvaro alvaro 2434 nov 21 10:11 known_hosts There are a bunch of other keys which aren't offered... why id_alvaro_mantra is offered and not the other keys? I can't understand. I need some help, don't know where to look....

  Read the article

• How to install two packages that write the same file

  - by Joel E Salas

  Sirs, a conundrum. I have two packages that each create /usr/bin/ffprobe. One of them is ffmpeg from the Deb Multimedia repository, while the other is ffmbc 0.7-rc5 built from source. The hand-rolled one is business-critical, and we used to just install it from source wherever it was necessary. I can only assume it would clobber the ffmpeg file, and there were never any ill effects. In theory, it should be acceptable for our ffmbc package to overwrite the file from the ffmpeg package. Is there any easy way to reconcile this?

  Read the article

• Managing a test iSCSI target server

  - by dyasny

  Hi all, I am using a RHEL server with a few hard drives, and tgtd as the iscsi target software. I a looking for a way to allocate and deallocate space and targets with that space, without restarting my system, or harming other LUNs. Currently, all my HDDs are PVs in a single VG, and I lvcreate/lvremove as required, and then export the allocated LVs using a tgt script: usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=1 --targetname iqn.2001-04.com.lab.gss:300gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 1 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_300Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 1 -I ALL /usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=2 --targetname iqn.2001-04.com.lab.gss:200gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 2 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_200Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 2 -I ALL /usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=3 --targetname iqn.2001-04.com.lab.gss:100gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 3 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_100Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 3 -I ALL tgtadm --mode target --op show So in order to remove a LUN, I stop the tgtd service, lvremove the lv, and remove the entry from the iscsi target script When I add a lun, I run lvcreate, and then add an entry to the script and run it. This is not quite optimal, since restarting the service is a bad idea while other LUNs are busy, so I am looking for a more scalable and safer way. Thanks

  Read the article

• samba share not on network after upgrading to Ubuntu 12.04LTS. [migrated]

  - by Sylvain Huard

  I just upgraded an old Ubuntu box to 12.04LTS (machine named A-Ubuntu). This is an upgrade not a format re-install. All the accounts and config were preserved. The basic setup is a local network with 2 Ubuntu machines (let say A-Ubuntu, B-Ubuntu) and a MAC (C-MAC). Before the upgrade, all of them could see each other by their names not only the IP address. The local network has a D-Link Router where everybody is connected with RJ-45 wired etherenet (not wi-fi). Since the A-Ubuntu upgrade, we can't see this machine name on the Network and its name is not on machine list in the D-Link router anymore. We can see it's IP address only. I can't access A-Ubuntu from the other two by its name but I can ping it with its address (192.168.0.109). From A-Ubuntu, I can connect and see the shared samba folders on B-Ubuntu and C-MAC. But from B-Ubuntu and C-MAc, I can't connect to A-Ubuntu. Correct me if I'm wrong but this tells me that Samba should be fine and the real problem is that A-Ubuntu does not advertise its name on the Network so the D-Link does not have it in its table so nobody else finds it. After a lot of googling, I see that it is the job of avahi and mdns to do so. Those packages are running, I checked multiple config files for samba, avahi, mdns to see as if it is like the examples on the WEB and also similar to what I find on the working B-Ubuntu machine. This is the same. I did multiple service restart with samba, avahi, remove the firewall to make sure it does not block the hostname broadcast. I rebooted multiple time to make sure the update I was making were effective. Still, Can't see the A-Ubuntu name on the network. Any idea what it can be?, Where to look next?

  Read the article

< Previous Page | 275 276 277 278 279 280 281 282 283 284 285 286  | Next Page >