Search Results

Search found 2355 results on 95 pages for 'dvd rom'.

Page 28/95 | < Previous Page | 24 25 26 27 28 29 30 31 32 33 34 35  | Next Page >

• Windows Server 2008 R2 install reboots unexpectedly during "Completing installation" phase

  - by knda

  I am attempting to install Windows Server 2008 R2 onto a Cisco UCS C201 M2 rack mounted server but am having major difficulties and wondering if anyone has some insight or items they could recommend for me to look at to get this one resolved. Installation is being attempted via the Cisco remote console (using CIMC's Virtual dvd-rom).. following the first phase of Setup where the installation files are copied to the target hard drive, then a reboot occurs to load Setup from the HDD, mid-way in the "Completing Installation" phase the system then reboots unexpectedly. System configuration Cisco UCS C201 M2 (2RU rack mounted server) 16GB RAM, 2x 73GB 15K SAS, 4x 300GB 10k SAS Add-on cards - Intel quad-port GigE card (no fibre channel cards) Storage - LSI MegaRAID SAS 9261-8i. onboard SATA is disabled (no SATA drives connected) KVM - Belkin No physical DVD-ROM.. :( I have... Run memtest86+, no RAM faults Disabled/enabled SATA support (BIOS) Attempted install from USB DVD-ROM, no effect Attempted unattended install scripted via Cisco Configuration Manager DVD provided Removed Belkin KVM in case that was causing drama Discovered that the Cisco website is "awesome" for searching for PDFs/Drivers cough, reverted back to Google Downloaded latest LSI drivers from LSI's site and used during Server 2008 install checked Windows ISO against checksum's from MS site checked Windows ISO by using it for an install in a VM Running out of ways to troubleshoot this as I am not sure how to enable any sort of 'verbose' mode during the setup process. Next step I have planned is to remove the Intel NIC and try the installation again.. Edit: Problem was the "Cisco INTEL QUAD PT GBE" (1000/PT) .. will have to see if this card is faulty or if it's just drivers.. thanks for the help.

  Read the article

• Problems installing Adobe Premiere Elements 8 Content features

  - by Walt Maken

  I recently purchased Adobe Photoshop & Premiere Elements 8. Photoshop Elements 8 installed fine, along with the additional material available via internet download. Premiere Elements 8 installed ok from the DVD. During the Premiere Elements 8 startup process the following message appears: A reduced set of content (Instant Movie Themes, Title and Menu Templates,etc) has been installed. To install the full content set, please insert your Content DVD and run Setup.exe. If you do not have a Content DVD please visit http://www.adobe.com/go/pre_additional_downloads to download the content installer. Since I didn't have the Content DVD, I did the download, which took nearly 12 hours. The extract appeared to complete at 100%, but then immediately gave the error message "A problem occurred while extracting some files. Check available space on your computer and the write privileges on the destination folder." Why would it show this error message if it had completed the extract process 100%? What step(s) do I take now to have Content installed? Do I need to go thru the 12 hour download again or, hopefully, is there something I can do that will make it unnecessary to download again?

  Read the article

• Acer recovering windows vista

  - by Charlie Pigarelli

  My computer history is very long even of my computer has 4 years of life. An year ago I installed Windows 7 on this acer m1610 that had Vista before. My technic left me 2 recovery disc for "acer vista" before updating it to Windows 7. Then the computer had some trouble. The graphic card broke and we decided to use another computer. Yesterday I had the great idea to fuse the two computer to have a better one... So I moved the graphic card of the latter computer to the acer and everything gone well. Then the trouble of speed, it had before, come back. So I decided to reinstall the very first Windows: Vista back again. I booted the computer with those 2 DVD-R my technic left me and at the end of the process it asked me to insert "the backup cd number one or the system disk". I found 2 original Acer "Blank Recovery Disc" DVD-R and tried with those: rejected. Tried with empty DVD-+R: rejected. I tried with CDs: rejected. I don't have any system disc with me. Except for those 2 DVD-R my technic left me. What am I supposed to do now? I even tried with these fantomatic alt+f9/f10 that should start the recovery without any disc... But nothing happened. PS: the installation cannot complete if I do not insert the right disk. (The recovery disc uses Acer eRecovery Management as recovery software.

  Read the article

• x display problems in centos 5.5

  - by John Ruiz

  I have a Dell E510 desktop with a geForce 7200 instead of the ATI x600 it came with. I have attempted to install CentOS 5.4 x86_64 (DVD), CentOS 5.5 (net install), and CentOS 5.5 x86_64 (DVD). Gnome desktop. All of these run into the same issue. When I put the DVD into the machine and reboot, the installer begins and I select "graphical install". I see text that say anaconda is starting, and then my screen goes nuts. It's not black, but rather a screen full of diagonal stripes or multiple colors. So I attempted to do a text install of CentOS 5.5 (DVD) and got it installed. When I booted for the first time, I logged into the virtual console and started X (startx). The desktop came up and it already had the display properties GUI up. I changed it from 800x600 to 1680x1050, saw that there were updates available, installed them, and then rebooted. When I start X from the virtual console this time, I get exactly the same display problem as I described before. Does anyone know what might be causing this and what I can do about it? edit: I should also mention that I'm capable of installing Windows 7 and Ubuntu 10.04 onto this machine with absolutely no issues at all.

  Read the article

• Is TortoiseSVN really this buggy?

  - by John Isaacks

  I have been using tortoise svn for a couple weeks now. I get errors very often. Almost everything I do creates an error. this is with repositories on the internet, locally on my machine or a machine on the network. So I started to keep track. Some examples are below. 12/31/2010 Can't move 'C:\Users\jisaacks\Desktop\my branch test.svn\tmp\entries' to 'C:\Users\jisaacks\Desktop\my branch test.svn\entries': The file or directory is corrupted and unreadable. 01/04/2011 Commit failed (details follow): Server sent unexpected return value (405 Method Not Allowed) in response to MKCOL request for '/svn/kranichs-svn/!svn/wrk/b316f15e-0869-4644-9c53-87aa0103506b/branches' 01/06/2011 Can't move 'C:\Users\jisaacks\Desktop\DVD Catalog\vendors.svn\tmp\entries' to 'C:\Users\jisaacks\Desktop\DVD Catalog\vendors.svn\entries': The file or directory is corrupted and unreadable. 01/06/2011 Can't move 'C:\Users\jisaacks\Desktop\DVD Catalog\cake\tests\test_app\views\layouts.svn\tmp\entries' to 'C:\Users\jisaacks\Desktop\DVD Catalog\cake\tests\test_app\views\layouts.svn\entries': The file or directory is corrupted and unreadable. 01/06/2011 Commit failed (details follow): attempt to write a readonly database attempt to write a readonly database That last one about the read only database happens every time I commit. Say if I am working on the head revision (7) in a working copy. I make a change and commit it. It gives me this error. But if I look at the log it tells me that there is now a revision 8 (the commit I just made) but I am still on revision 7. So I need to run update to be on the current revision that I just commited. I hope I explained that clearly. Anyways with all these errors I wonder.. Is TSVN just this unstable, does everyone have these issues. Or is it just me? If just me, what could I be doing wrong?

  Read the article

• Computer always freezing after random periods of time. No errors listed.

  - by Wesley

  Hi, all. Here are my specs beforehand: AMD Athlon XP 2400+ @ 2.00 GHz, 160GB IDE HDD, 128MB GeForce 6200 AGP, 2 x 512MB PC3200 DDR RAM, CoolMax 350W PSU, 1 x CD-RW Drive, 1 x DVD-ROM Drive, FIC AM37 Mobo, Windows XP Pro SP3 My desktop freezes after random periods of time but there are no errors listed in the Event Viewer after a forced shutdown and restart. A couple months ago, I found that when it froze, the floppy was being accessed at the same time. So, I disconnected the floppy (since I never used it anyways) from the power supply and motherboard. Everything was working fine and the computer never froze. This past Christmas break, I left for a Conference and when I got home, the computer kept freezing again. So, this time, I just disconnected the DVD reader (from mobo and power) and started it up. Still, it froze almost right away. Then I found some older sticks of RAM (2 x 256MB PC2100 DDR) and swapped them in. Everything worked fine again after that. I even swapped the 2 x 512MB PC3200 DDR RAM back in and everything worked okay. Then it started freezing again, and I tried all possible RAM combos, still freezing within 5-10 minutes of startup. One thing I've realized is that the floppy drive is still listed in My Computer and I uninstalled it from my Device Manager already. There were no software errors, and I uninstalled the most recent software, with no effect. Still, I have no idea what is wrong because everything ran fine before that. Any suggestions? EDIT: Still have yet to buy some blank CD media to use Memtest86+. However, would a lack of virtual memory cause the computer to freeze? EDIT2: So after a long time, I ran Memtest86+ and all is well. Turns out though, after removing my original DVD reader and replacing it with a DVD-ROM drive, there is no freezing whatsoever! Thanks for all your suggestions!

  Read the article

• Dialog box tells me there's a missing driver when installing 64-bit version of Windows 7

  - by Eikern

  I'm trying to install Windows 7 64-bit on my computer (ASUS P6T Deluxe V2, one 80GB HDD and two 1 TB HDDs). When I'm supposed to select whether I want to Upgrade or do a Custom install, I get a dialog box telling me: Load Driver A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the Windows installation media is in the CD/DVD drive, you can safely remove it for this step. I've tried to reach this step using a 32-bit installation disc, but that doesn't generate this message at all. Through the command windows (shift-F10) I can reach all of my drives, including my optical drive, without any problems--so what kind of device driver is it the installation wants? I've tried all the obvious drivers on the CD that followed my motherboard, but I can't seem to find the right one. The problem is that I don't know what device I'm supposed to load the drivers for in the first place. Can anyone help me? Edit: It turned out that my downloaded image was corrupted. I borrowed a DVD from a friend of mine, which worked!

  Read the article

• Errors while updating Ubuntu 13.10

  - by santiago

  When I execute the updater it always throws the same error saying: Failed to download repository information. Check your internet connection. And when I run the sudo apt-get update I get these lines at the end: W: Failed to fetch cdrom://Ubuntu 13.10 Saucy Salamander - Release i386 (20131016.1)/dists/saucy/main/binary-i386/Packages Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs W: Failed to fetch cdrom://Ubuntu 13.10 Saucy Salamander - Release i386 (20131016.1)/dists/saucy/restricted/binary-i386/Packages Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs W: Failed to fetch http://ppa.launchpad.net/tiheum/equinox/ubuntu/dists/saucy/main/source/Sources 404 Not Found W: Failed to fetch http://ppa.launchpad.net/tiheum/equinox/ubuntu/dists/saucy/main/binary-i386/Packages 404 Not Found E: Some index files failed to download. They have been ignored, or old ones used instead

  Read the article

• Playing NSF music in FMOD.net

  - by Tesserex

  So, as the title says, I want to be able to play NSF files using FMOD, because my project already uses FMOD and I'd rather not replace it. This will involve figuring out how existing players and emulators work and porting it. I haven't yet found an existing player that uses FMOD. My starting point is the MyNes source from http://sourceforge.net/projects/mynes/. There are two big steps between here and what I'm looking for. MyNes plays from a ROM, not NSF. So, I have to rip out the APU and get it to play NSF files. The MyNes APU uses SlimDX, so I have to convert that to FMOD.NET. I am really stuck about how to go about either of these, because I'm not that familiar with audio formats and it's hard finding resources online. So here are a few questions: From what I can tell from the NSF spec at http://kevtris.org/nes/nsfspec.txt, it's just contains the relevant memory section of the ROM, plus the header. If anyone can verify or correct this that would be great. The emulator APU uses data from the rest of the emulator to play, including things like cycle counts. I'm not sure what replaces this in a standalone player. Can't I just load all the music data at once into a stream and play it? Joining #1 and #2, does the header data from the NSF substitute for some of the ROM data in the emulator code? Using FMOD, will I be following the usercreatedsound example for loading a stream? And does this format count as PCM? Specifically MyNes says PCM8. Any tips on loading / playing the stream in FMOD are appreciated. As an aside, I don't really understand the loading / playing sections of the spec I linked at all. It seems to apply to 6502 systems / emulators only and not to my situation. I know it's a long shot for anyone here to have enough experience in this area to help, but anything you can provide is definitely appreciated. A link to an existing .NET library that does this would be even better, but I don't believe one exists.

  Read the article

• How to boot Ubuntu 12.04-64bit from a USB from Compaq CQ58

  - by user208092

  I try to boot Ubuntu 12.04, 64-bit on my Compaq CQ58 laptop from a USB but it is not working. I've correctly installed the Ubuntu on my pen drive following the instructions on Ubuntu website. (http://www.ubuntu.com/download/desktop/create-a-usb-stick-on-windows) These are my BIOS settings: Post Hotkey Delay (sec) <0 CD-ROM Boot Internal Network Adapter Boot Network Boot Protocol Legacy Support Secure Boot Platform Key Enrolled Pending Action None Clear All Secure Boot UEFI Boot Order: USB Diskette on Key/USB Hard Disk OS Boot Manager Internal CD/DVD ROM Drive ! Network Adapter With these settings when i restart my computer what shows up is: Boot Device Not Found. This is what I get on the Boot Manager: Boot Option Menu OS boot Manager Boot From EFI File (Arrow Up) and (Arrow Down) to change option, ENTER to select an option. Press F10 to BIOS Setup Options, ESC to exit. PLEASE HELP... P.S. My laptop has windows 8

  Read the article

• Playing NSF music in FMOD.net

  - by Tesserex

  So, as the title says, I want to be able to play NSF files using FMOD, because my project already uses FMOD and I'd rather not replace it. This will involve figuring out how existing players and emulators work and porting it. I haven't yet found an existing player that uses FMOD. My starting point is the MyNes source from http://sourceforge.net/projects/mynes/. There are two big steps between here and what I'm looking for. MyNes plays from a ROM, not NSF. So, I have to rip out the APU and get it to play NSF files. The MyNes APU uses SlimDX, so I have to convert that to FMOD.NET. I am really stuck about how to go about either of these, because I'm not that familiar with audio formats and it's hard finding resources online. So here are a few questions: From what I can tell from the NSF spec at http://kevtris.org/nes/nsfspec.txt, it's just contains the relevant memory section of the ROM, plus the header. If anyone can verify or correct this that would be great. The emulator APU uses data from the rest of the emulator to play, including things like cycle counts. I'm not sure what replaces this in a standalone player. Can't I just load all the music data at once into a stream and play it? Joining #1 and #2, does the header data from the NSF substitute for some of the ROM data in the emulator code? Using FMOD, will I be following the usercreatedsound example for loading a stream? And does this format count as PCM? Specifically MyNes says PCM8. Any tips on loading / playing the stream in FMOD are appreciated. As an aside, I don't really understand the loading / playing sections of the spec I linked at all. It seems to apply to 6502 systems / emulators only and not to my situation. I know it's a long shot for anyone here to have enough experience in this area to help, but anything you can provide is definitely appreciated. A link to an existing .NET library that does this would be even better, but I don't believe one exists.

  Read the article

• Get the following error when running Software Updater

  - by Curtis Cox

  W:Failed to fetch cdrom://Ubuntu 12.10 Quantal Quetzal - Beta i386 (20120926)/dists/quantal/main/binary-i386/Packages Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs , W:Failed to fetch cdrom://Ubuntu 12.10 Quantal Quetzal - Beta i386 (20120926)/dists/quantal/restricted/binary-i386/Packages Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs , E:Some index files failed to download. They have been ignored, or old ones used instead.

  Read the article

• How can I determine which GPU card is running at PCI Express 2.0 x16 & which is using x8?

  - by M. Tibbits

  Is there a way to determine the speed of the PCI Express connection to a specific card? I have three cards plugged in: two Nvidia GTX 480's (one at x16 & and one at x8) one Nvidia GTX 460 running at x8 Is there some way, either by a function call in C or an option to lspci that I can determine the bus speed of the graphics cards? When I only use one of the cards for my CUDA program, I'd like to use the one which is running at x16. Thanks! Note: lspci -vvv dumps out For the two GTX 480s. I don't see any differences that pertain to bus speed. 03:00.0 VGA compatible controller: nVidia Corporation Device 06c0 (rev a3) Subsystem: eVga.com. Corp. Device 1480 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=32M] Region 1: Memory at b0000000 (64-bit, prefetchable) [size=128M] Region 3: Memory at bc000000 (64-bit, prefetchable) [size=64M] Region 5: I/O ports at df00 [disabled] [size=128] [virtual] Expansion ROM at b8000000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb, nouveau 03:00.1 Audio device: nVidia Corporation Device 0be5 (rev a1) Subsystem: eVga.com. Corp. Device 1480 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 5 Region 0: [virtual] Memory at d7ffc000 (32-bit, non-prefetchable) [disabled] [size=16K] Capabilities: <access denied> 04:00.0 VGA compatible controller: nVidia Corporation Device 06c0 (rev a3) Subsystem: eVga.com. Corp. Device 1480 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=32M] Region 1: Memory at c0000000 (64-bit, prefetchable) [size=128M] Region 3: Memory at cc000000 (64-bit, prefetchable) [size=64M] Region 5: I/O ports at cf00 [size=128] [virtual] Expansion ROM at c8000000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb, nouveau 04:00.1 Audio device: nVidia Corporation Device 0be5 (rev a1) Subsystem: eVga.com. Corp. Device 1480 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 5 Region 0: Memory at dfffc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> And the only differences I see relate specifically to the memory mapping: myComputer:~> diff card1 card2 3c3 < Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- --- > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- 7,11c7,11 < Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=32M] < Region 1: Memory at b0000000 (64-bit, prefetchable) [size=128M] < Region 3: Memory at bc000000 (64-bit, prefetchable) [size=64M] < Region 5: I/O ports at df00 [disabled] [size=128] < [virtual] Expansion ROM at b8000000 [disabled] [size=512K] --- > Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=32M] > Region 1: Memory at c0000000 (64-bit, prefetchable) [size=128M] > Region 3: Memory at cc000000 (64-bit, prefetchable) [size=64M] > Region 5: I/O ports at cf00 [size=128] > [virtual] Expansion ROM at c8000000 [disabled] [size=512K] 18c18 < Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- --- > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- 19a20 > Latency: 0, Cache Line Size: 64 bytes 21c22 < Region 0: [virtual] Memory at d7ffc000 (32-bit, non-prefetchable) [disabled] [size=16K] --- > Region 0: Memory at dfffc000 (32-bit, non-prefetchable) [size=16K]

  Read the article

• Can't install alternate CD from USB?

  - by mattias

  Hi im trying to install ubuntu 12.04 with full hard disk encryption. After downloading and installing the Ubuntu live CD, I learned that truecrypt doesnt support full disk encryption on linux. I also learned that the best way to get "nearly full disk encryption" on ubuntu is by installing it from the alternate install CD. I tried that, but something is wrong with my CD reader/burner so it doesnt boot up when i insert the cd. My thought here was to take the .iso that I downloaded on my unencrypted Ubuntu system, use Unetbootin to make the usb drive. The usb drive used for this is exactly the same brand as one that I know has worked with a previous ubuntu live system on the same computer. I also used unetbootin for that usb, but I created it from windows that time. The usb stick boots up fine and i get through the first couple of steps in the installation process. However, After a while I get a "box" with the following error message "Load Installer components from CD" There was a problem reading data from the CD-ROM. Please make sure it is in the drive. If retrying does not work, you should check the integrity of your CD-ROM. "Failed to copy file from CD-ROM. Retry? " Then I cant get any further. I googled a lot and found this page which seems to tackle this very problem: http://www.dotkam.com/2010/11/29/ins...mage-from-usb/ I tried to do what it said. After pressing TAB, I wrote : cdrom-detect/try-usb=true without quotes because that's what i think is right. When I press TAB, there already is a text saying : /ubnkern initrd=/ubninit vga=788 -- quiet which can be removed. I have tried to both delete the text before the "--" and just inserting cdrom-detect/try-usb=true before it. Any idea of what can be wrong? I would like to do a full system encryption, or as full as it is possible. I dont want to just encrypt my /home folder. Maybe this isn't the easiest way. I use SanDisk usb sticks. I know there is a problem with U3 launcher on some SanDisks, but I never had to remove U3 before from similar disks, and the alternate install does boot up, so I dont think using U3 removal would help me. Any help or indication to an easier way to do this would be appreciated

  Read the article

• The Internet Key Wave MW833UP is not recognized in Ubuntu

  - by gio900

  I can't use my Onda MW833UP... :( Any advice? Here is something that someone else may understand: ~$: lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric ~$: lsusb Bus 001 Device 005: ID 1ee8:0012 ~$: dmesg [ 22.709475] cdc_acm 1-1:1.0: ttyACM0: USB ACM device [ 22.714856] usbcore: registered new interface driver cdc_acm [ 22.714866] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 23.520490] ieee80211 phy0: wl_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) [ 24.244530] usbcore: registered new interface driver usbserial [ 24.244575] USB Serial support registered for generic [ 24.244673] usbcore: registered new interface driver usbserial_generic [ 24.244681] usbserial: USB Serial Driver core [ 24.265879] USB Serial support registered for GSM modem (1-port) [ 24.285680] usbcore: registered new interface driver option [ 24.285691] option: v0.7.2:USB Driver for GSM modems [ 24.425878] EXT4-fs (sda9): re-mounted. Opts: errors=remount-ro,commit=600 [ 24.736540] EXT4-fs (sda8): re-mounted. Opts: commit=600 [ 35.705796] Easy slow down manager: checking for SABI support. [ 35.706002] Easy slow down manager: SABI is supported (f5189) [ 36.060099] usbcore: deregistering interface driver uvcvideo [ 139.508061] CE: hpet increased min_delta_ns to 20113 nsec [ 6798.378917] usb 1-1: USB disconnect, device number 5 [ 6809.108232] usb 1-1: new high speed USB device number 6 using ehci_hcd [ 6809.242692] scsi5 : usb-storage 1-1:1.0 [ 6810.241257] scsi 5:0:0:0: CD-ROM Onda Datacard CD-ROM 0001 PQ: 0 ANSI: 0 [ 6810.241841] scsi 5:0:0:1: Direct-Access Onda Storage 0001 PQ: 0 ANSI: 0 [ 6810.271410] sr0: scsi3-mmc drive: 0x/0x caddy [ 6810.272099] sr 5:0:0:0: Attached scsi CD-ROM sr0 [ 6810.272852] sr 5:0:0:0: Attached scsi generic sg1 type 5 [ 6810.279954] sd 5:0:0:1: [sdb] Attached SCSI removable disk [ 6810.281210] sd 5:0:0:1: Attached scsi generic sg2 type 0 [ 6810.380591] sr0: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00 [ 6810.380617] sr: Sense Key : Hardware Error [current] [ 6810.380625] sr: Add. Sense: No additional sense information [ 6810.613937] sr0: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00 [ 6810.613972] sr: Sense Key : Hardware Error [current] [ 6810.613984] sr: Add. Sense: No additional sense information [ 6810.673716] usb 1-1: USB disconnect, device number 6 [ 6815.572142] usb 1-1: new high speed USB device number 7 using ehci_hcd [ 6815.706828] cdc_acm 1-1:1.0: ttyACM0: USB ACM device The last 3 lines are where I inserted the Internet key, then reconnected it. usb-device T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1ee8 ProdID=0012 Rev=00.01 S: Manufacturer=Onda S: Product=MW833UP S: SerialNumber=9230B35D870F9CB7AE684EACC5C12BE5EC33B26E C: #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=01 Driver=cdc_acm I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm Then there is /dev/ttyACM0. When the key is connected to the USB port, everything that will meant...

  Read the article

• when i marked all check boxes in settings,update fails.

  - by user67966

  "W:Failed to fetch cdrom://Ubuntu 12.04 LTS Precise Pangolin - Release i386 (20120423)/dists/precise/main/binary-i386/Packages Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs , W:Failed to fetch cdrom://Ubuntu 12.04 LTS Precise Pangolin - Release i386 (20120423)/dists/precise/restricted/binary-i386/Packages Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs , E:Some index files failed to download. They have been ignored, or old ones used instead." the above information is a crash info.It happens when i manually update ubuntu.I have marked all check-boxes in settings which was by default not marked. What is the main reason for this problem?

  Read the article

• 11.10 - Update Manager Not working

  - by Mattlinux1

  W:Failed to fetch cdrom://Ubuntu 11.10 Oneiric Ocelot - Release i386 (20111012)/dists/oneiric/main/binary-i386/Packages Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs , W:Failed to fetch cdrom://Ubuntu 11.10 Oneiric Ocelot - Release i386 (20111012)/dists/oneiric/restricted/binary-i386/Packages Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs , E:Some index files failed to download. They have been ignored, or old ones used instead. This happens when i hit the check button? and the updates were working before.

  Read the article

• Update information outdated, "Failed to fetch cdrom"

  - by user285603

  I have a warning triangle on the top of my screen. When I click on it, it says that my update information is outdated. When I type sudo apt-get update && sudo apt-get upgrade into a terminal, I get this message: W: Failed to fetch cdrom://Ubuntu 14.04 LTS _Trusty Tahr_ - Release i386 (20140417)/dists/trusty/main/binary-i386/Packages Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs W: Failed to fetch cdrom://Ubuntu 14.04 LTS _Trusty Tahr_ - Release i386 (20140417)/dists/trusty/restricted/binary-i386/Packages Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs E: Some index files failed to download. They have been ignored, or old ones used instead. Any ideas?

  Read the article

• disable intel gpu in ubuntu 12.04

  - by small_potato

  I am wondering if there is anything to disable the intel gpu on ubuntu 12.04. I want to be able to setup dual monitor using nvidia-settings. It seems the intel gpu is used for display as suggested by sudo lshw -c display the output is *-display description: VGA compatible controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:16 memory:c0000000-c0ffffff memory:90000000-9fffffff memory:a0000000-a1ffffff ioport:4000(size=128) memory:a2000000-a207ffff *-display description: VGA compatible controller product: Haswell Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 06 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:47 memory:c2000000-c23fffff memory:b0000000-bfffffff ioport:5000(size=64) I have a lenovoY410 with GT750M. It seems there is no way to turn off the intel gpu in bios either. Help please. Thanks.

  Read the article

• What are "Failed to fetch cdrom" errors in Update Manager and how do I fix them? [closed]

  - by gcc

  Possible Duplicate: Failed to download repository information due to missing CDROM Whenever I run update-manager, I am getting the following error: Failed to fetch cdrom://Ubuntu 10.04.2 LTS _Lucid Lynx_ - Release amd64 (20110211.1)/dists/lucid/main/binary-amd64/Packages.gz Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs Failed to fetch cdrom://Ubuntu 10.04.2 LTS _Lucid Lynx_ - Release amd64 (20110211.1)/dists/lucid/restricted/binary-amd64/Packages.gz Please use apt-cdrom to make this CD-ROM recognized by APT. apt-get update cannot be used to add new CD-ROMs Failed to fetch http://ppa.launchpad.net/qwibber-daily/ppa/ubuntu/dists/lucid/main/binary-amd64/Packages.gz 404 Not Found How can I get rid of these errors? What is this error trying to tell me?

  Read the article

• Can't Install Windows 2008 R2 on Lenovo Laptop With SSD

  - by Ben

  I am trying to install Windows Server 2008 R2 on a new Lenovo X201 or T410 laptop. Setup halts with the following pop-up: A required CD/DVD device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the windows installation media is in the CD/DVD drive you can safely remove it for this step. The CD drive is obviously working, as it's booting from CD to get to this point. The only thing I can think is that it is to do with the fact they have SSD disks in - but that's just a guess. (Edit - One extra thing that may or may not be relevant: it's the 64 bit version of Server 2008 R2)

  Read the article

• Windows 7: Can't see ISO file in C:\

  - by cbp

  I used DVD shrink to create an ISO file and saved it into C:\ The ISO file is visible with some programs but not with others. The file is not hidden as far as I am aware. But it cannot be seen by Windows Explorer, DVD Decrypter or a bunch of other programs. If I search for the file using Windows 7's Start Menu search tool, I can see the file and I can right click and select Properties. The Properties window appears OK, but if I try to change tabs on the property window, I receive an error message as though the file is not there. DVD Shrink can still open the file OK. I can also find the file using Agent Ransack (a file searching tool), but then I cannot open it. What gives?

  Read the article

• Can't Install Windows 2008 R2 on Lenovo Laptop With SSD

  - by Ben

  I am trying to install Windows Server 2008 R2 on a new Lenovo X201 or T410 laptop. Setup halts with the following pop-up: A required CD/DVD device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the windows installation media is in the CD/DVD drive you can safely remove it for this step. The CD drive is obviously working, as it's booting from CD to get to this point. The only thing I can think is that it is to do with the fact they have SSD disks in - but that's just a guess.

  Read the article

• HP Recovery Manager failed creating a backup disc

  - by Baehr

  I had to restore my computer (running Windows 7) back to its factory default, so I ran the HP recovery manager disc and chose to reformat my computer. Before doing this I was given an option to backup my current files to a DVD, and I did so; getting the confirmation of a successful DVD burn. Booting up my computer everything looks like it did when I first purchased it (like expected). But when I pop in the backup DVD and run the recovery EXE inside it, the application creates a directory inside C:\System Recovery Files which contains the empty directories: [(^_^)] and Program Data. So essentially what I'm getting out of this is a failure in creating a back-up. Which is not only confusing but incredibly frusterating. Is there any way that I can recover the files lost in the

  Read the article

• I have recovery issues in my Gateway nv series laptop

  - by kshitij

  Helo i wanted to restore os from my recovery drive. but because of some issues i could not do that. so i had my recovery dvds which i made when i bought laptop. these are three dvds. so i inserted one dvd and installation started. and it asked for second dvd and i inserted but it is not taking it. once i did installtion with this three dvds but now it is not taking second dvd. So because of this type of failure i install trial version of windows 7 and take my backup. after it i install Gateway recovery Management. and it is not working. when i am repair my computer it is not showing that Image of recovery partition. Please I need Help.

  Read the article

< Previous Page | 24 25 26 27 28 29 30 31 32 33 34 35  | Next Page >