Search Results

Search found 2516 results on 101 pages for 'gigabit ethernet'.

Page 28/101 | < Previous Page | 24 25 26 27 28 29 30 31 32 33 34 35  | Next Page >

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• Sharing internet connection from Windows XP using wi-fi router

  - by Darius

  Hi, I have an network configuration like: Ethernet cable from ISP connected to Windows XP machine, configured with static IP 192.168.0.3 Another ethernet connection from 2nd Windows XP machine's network adapter to a Wi-Fi router (D-Link Airport G+) XP set to "Share internet connection", the 2nd adapter configured as static to 192.169.0.1 D-Link Airport Wi-Fi router also configured as "static connection", it's IP set to 192.169.0.2, default gateway set to 192.169.0.1. Network mask everywhere is 24. Laptop computer connected with the router with static IP 192.169.0.3 The problems are: XP machine sees the router (it's able to ping it and access it via the web admin tool) The router somehow cannot PING the XP machine (using the tool provided by the web-based admin tool) The laptop computer cannot ping anything and cannot be pinged The router is only accessible when the ethernet cable is connected with a router's 1-4 LAN port, when I connect it via "WAN" port (which I believe is the proper one) it's not visible from the XP machine If you have similar experience with configuring a network like this I would really appreciate your help. I cannot use the Wi-Fi router with the ISP cable itself.

  Read the article

• Laptop connects to other network but not to my home wireless

  - by Nilesh

  My home network's wireless SSID is say "XYZ" I also have an ethernet wire from the same router. I have two laptops A and B Earlier both A and B were able to connect to my home internet through the ethernet and wireless. Suddenly, the laptop B can no longer connect to XYZ or through ethernet. When I do plug the wire, i get the connection icon all green but when I try to access any web page it errors out (page not found) But strangely laptop B connects to my neighbours wireless SSID "ABC". I have also tested laptop B with other networks and it connects fine. Laptop A and many other devices still connect fine with my home wireless "XYZ" Strange thing is when my laptop B connects wireless through XYz, it gets the IP address but then none of the browsers (chrome,firefox, IE) can show any web pages. What settings should I be checking on laptop B that is preventing it to connect to my home internet. Thank you

  Read the article

• ipconfig /release not working, why?

  - by barlop

  ipconfig /release is not working, why is that? here is a sequence where I put my cable in get an IP, try ipconfig /release and it tells me it can't release wireless, but there is no wireless connection. i'm just trying to release the wired one. C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Fine so I plug my cable in C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 0.0.0.0 Subnet Mask . . . . . . . . . . . : 0.0.0.0 Default Gateway . . . . . . . . . : C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.1.8 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.254 Fine so from above, it clearly has an iP C:\>ipconfig /release Windows IP Configuration No operation can be performed on Wireless Network Connection while it has its me dia disconnected. C:\>

  Read the article

• Configuring Wireless Network

  - by Vinod K

  I have vyataa router on VMware with 2 interfaces eth0 and eth1 eth0 is facing the internet eth0 is in Nat mode with dhcp on eth1 is in bridged mode with my ethernet with ip 10.0.2.34/24 The ethernet card is at ip 10.0.2.95/24 i have defined the nat rule. Hence internet is available at eth1 too. Now i am connecting a wireless router at "eth1" iball router, I have connected the router using a cable to the ethernet interface of my laptop. I have configured the WAN connection type as "Static IP" and given "10.0.2.34/24" All the clients that connect using wireless router cannot connect to the internet though. Could anyone provide me a solution for this.. Thank You!!

  Read the article

• Computer never connects to the internet automatically on startup?

  - by RawR Crew

  I have my Windows Vista laptop connected directly to the router via an ethernet cable, and every time I switch the computer on, the computer cannot connect to the internet. It comes up as limited or no connectivity, I am assuming because it has not been assigned an IP address by the router - not too sure if this is right. The problem is usually fixed either by performing a repair through the networking control panel or removing and re-inserting the ethernet cable. It will also connect without doing any of these if the computer is left idle for about 20 minutes. It will connect fine wirelessly without the need for any of this, however I would prefer to connect via the cable. Any ideas how I can fix this? I have replaced the ethernet cable and router already (identical model) but these haven't helped. Thanks for any help on this.

  Read the article

• Laptop connects to other network but not to my home wireless

  - by Nilesh

  My home network's wireless SSID is say "XYZ" I also have an ethernet wire from the same router. I have two laptops A and B Earlier both A and B were able to connect to my home internet through the ethernet and wireless. Suddenly, the laptop B can no longer connect to XYZ or through ethernet. When I do plug the wire, i get the connection icon all green but when I try to access any web page it errors out (page not found) But strangely laptop B connects to my neighbours wireless SSID "ABC". I have also tested laptop B with other networks and it connects fine. Laptop A and many other devices still connect fine with my home wireless "XYZ" Strange thing is when my laptop B connects wireless through XYz, it gets the IP address but then none of the browsers (chrome,firefox, IE) can show any web pages. What settings should I be checking on laptop B that is preventing it to connect to my home internet. Thank you

  Read the article

• Wi-fi signal with keeping the internet cable

  - by daGrevis

  So the situation is that I have Ethernet cable which provides internet to my computer. Thing I want is to have wi-fi connection in my house and Ethernet cable (like I have before) to use for my PC. I will use wi-fi for my laptop and mobile phone. I think I need router for that and I'm looking at Asus RT-N16 (suggested in Coding Horror) for it, but I am not sure. Is it the right thing for me and I will be able to get wi-fi signal and keep the Ethernet cable? I guess the system will be that current cable goes into router, router provides wi-fi signal and gives back new cable... or something like that. Thanks in any advice! And sorry if topic isn't in right site.

  Read the article

• Establish direct cable connection between Windows 8 PCs in home network

  - by Marie. P.

  I'm running two PCs, a desktop and a laptop with Windows 8 Release Preview ("Build 8400"). They are connected to the same router in infrastructure mode, thereby having wireless internet. Due to often file synchronization between the machines I want to establish a cable connection that allows direct file transfer, without needing to use the wireless. When I plug in the cable (normal, not cross-over), I see in "Control Panel\Network and Internet\Network Connections": "Ethernet - unidentified Network" on both PCs. Transferring a file between both still only uses the WiFi via the Router. I noticed that when turning off the wifi on one PC, I can set up a shared internet connection that will work via Ethernet-cable, but since sometimes only one PC runs, sometimes the other one, I do not want to have the internet of one machine to be dependent on the other one being switched on. I do not have a crossover-cable, but since I did connect the PCs already successfully (just without both being on the internet), I'm sure that this should also work with a normal ethernet cable.

  Read the article

• Change ip route metric

  - by notphunny

  I'm constantly switching between eth0 and wlan0 interface on my archlinux because I often change OpenWrt fw images on my second router (which isn't connected anywhere). So I have problem with my routes when I'm connected to my wlan and want to connect with Ethernet to my router. Both routers are on 192.168.1.1/24 and after connecting to my Ethernet profile eth0 route becomes default one (which is ok for the time), because of smaller metric I guess. So I'm interested, how can I change routes metric so my applications can be connected to the internet (through out wlan)? Maybe there is solution not to use Default Gateway on Ethernet profile, however I still want to know how to change metric. Or default route if there are more then one.

  Read the article

• Wireless doesn't work on a Lenovo V570

  - by Stephen

  I've had Ubuntu installed on my HD for about 3 months but ever since I ran into this wireless issue I kinda lost my lust of Ubuntu. I have zero experience getting around with/ using the console command. I have a Lenovo V570. I got the driver update for the broadcom networking card via the Additional Drivers application but that did nothing. I love the look and feel of using Ubuntu but I have no technological experience for the matter. Any help would be awesome. When I scan for wireless connections while in Ubuntu, my computer picks up nothing, while on Win7 it will pick up the handful of wireless networks around my area. My wired connection is fine, but the use of not having wireless on a laptop is rather contradictory to it as a feature. Cheers! Also, I just installed 11.10, if that helps any. Yes, I used the search before I posted this, but again I have ZERO understanding of the command stuff and need a meat and potatoes answer(s). stephen@ubuntu:~$ sudo lshw -class network [sudo] password for stephen: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f1900000-f1903fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: 06 serial: f0:de:f1:63:98:14 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.1.78 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff stephen@ubuntu:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• Wireless will not connect

  - by azz0r

  Hello, I have installed Ubuntu 10.10 on the same machine as my windows setup. However, it will not connect to my wireless network. It can see its there, it can attempt to connect, yet it will never connect. It will keep bringing up the password prompt everyso often. I have tried turning my security to WEP, I ended up turning it back to WPA2. It is set to AES (noted a few threads on google about that). Can you assist? I would love to dive into Ubuntu, but without the internet its pointless. --- lshw -C network --- *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 00:1d:92:ea:cc:62 capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.020.00-NAPI duplex=half latency=0 link=no multicast=yes port=twisted pair resources: irq:29 ioport:e800(size=256) memory:feaff000-feafffff memory:f8ff0000-f8ffffff(prefetchable) memory:feac0000-feadffff(prefetchable) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:15:af:72:a4:38 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bgn --- iwconfig ---- lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Wuggawoo" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Tx-Power=9 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on --- cat /etc/network/interfaces ---- auto lo iface lo inet loopback logs deamon.log --- Jan 19 04:17:09 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:11 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): association took too long. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 5 -> 6 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): asking for new secrets Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 6 -> 4 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 4 -> 5 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): connection 'Wuggawoo' has security, and secrets exist. No new secrets needed. Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'ssid' value 'Wuggawoo' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'scan_ssid' value '1' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'key_mgmt' value 'WPA-PSK' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'psk' value '<omitted>' Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_engine_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_module_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: set interface ap_scan to 1 Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:13 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:23 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:24 ubuntu AptDaemon: INFO: Initializing daemon Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:25 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:27 ubuntu NetworkManager: <info> wlan0: link timed out. --- kern.log --- Jan 19 04:18:11 ubuntu kernel: [ 142.420024] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:13 ubuntu kernel: [ 144.333847] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:13 ubuntu kernel: [ 144.539996] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:13 ubuntu kernel: [ 144.750027] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:14 ubuntu kernel: [ 144.940022] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:25 ubuntu kernel: [ 155.832995] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:25 ubuntu kernel: [ 156.030046] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:25 ubuntu kernel: [ 156.230039] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:25 ubuntu kernel: [ 156.430039] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out --- syslog --- Jan 19 04:18:46 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:18:48 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:18:48 ubuntu kernel: [ 178.833905] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:48 ubuntu kernel: [ 179.030035] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:48 ubuntu kernel: [ 179.230020] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:48 ubuntu kernel: [ 179.433634] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out lspci and lsusb lspci -- 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:00.0 VGA compatible controller: nVidia Corporation G80 [GeForce 8800 GTS] (rev a2) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 03:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller -- lsusb -- Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 004 Device 002: ID 045e:0730 Microsoft Corp. Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 13d3:3247 IMC Networks 802.11 n/g/b Wireless LAN Adapter Bus 002 Device 002: ID 0718:0628 Imation Corp. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 046d:08c2 Logitech, Inc. QuickCam PTZ Bus 001 Device 002: ID 0424:2228 Standard Microsystems Corp. 9-in-2 Card Reader Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub With no security on my router I still can't connect, I get: Jan 19 15:58:01 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: WPS-AP-AVAILABLE Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Association request to the driver failed Jan 19 15:58:02 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 15:58:05 ubuntu NetworkManager: <info> wlan0: link timed out. Jan 19 15:58:07 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connec

  Read the article

• Internet suddenly stopped working

  - by user95629

  I was using NoMachine to access Ubuntu 11.10 when suddenly the internet on Ubuntu stopped working. Now Ubuntu doesn't recognize the internet at all (including locally). Symptoms: Doesn't recognize the fact that there is an ethernet cable attached. (I've tried switching cables, didn't work.) GUI says "No network devices available" Can't ping external IP addresses. Tried changing /etc/network/interfaces to eth1 instead of eth0 but it didn't work. ifconfig provides no output relating to eth0. When I type "/etc/init.d/networking restart" it tells me "Cannot find device 'eth0'/Failed to bring up eth0." The network settings had used a static IP address prior to the crash. I don't know why it won't recognize the ethernet (I think this is the fundamental problem, but I might be wrong) and why it stopped working so suddenly--I haven't installed any updates lately. Any ideas? Any more information I should provide? EDIT: lspci recognizes the Ethernet controller; netstat does not. lspci calls it "Intel Corporation Device 0000"

  Read the article

• WPA2 authentication fails on Ubuntu 12.04 using Rosewill RNX-N1

  - by user94156

  Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. RNX-X1 works on other systems (including TV); also have 2 of 'em and tried each. Worth noting that I recently switched from Comcast to CenturyLink and so switched routers. The system connected successfully to previous router (Linksys EA4500) using WPA2. Would think it is the router (Actiontec C1000A) but all other devices (TV, iPad, Windows, Blackberry, and Squeezebox) connect ok. Would appreciate some diagnostic guidance and insight (phrased for a newbie!) Tests to date: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 00:e0:4d:30:40:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:ac00(size=256) memory:fdcff000-fdcfffff memory:fdb00000-fdb1ffff *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan1 serial: 00:02:6f:bd:30:a0 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.2.0-31-generic firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn sudo lspci -v 00:00.0 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: NVIDIA Corporation MCP67 ISA Bridge (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 00:01.1 SMBus: NVIDIA Corporation MCP67 SMBus (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: 66MHz, fast devsel, IRQ 11 I/O ports at fc00 [size=64] I/O ports at 1c00 [size=64] I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:01.2 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Flags: 66MHz, fast devsel 00:02.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:04.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:06.0 IDE interface: NVIDIA Corporation MCP67 IDE Controller (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Kernel driver in use: pata_amd Kernel modules: pata_amd 00:07.0 Audio device: NVIDIA Corporation MCP67 High Definition Audio (rev a1) Subsystem: Biostar Microtech Int'l Corp Device 820c Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:08.0 PCI bridge: NVIDIA Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: fd000000-fd0fffff Capabilities: [b8] Subsystem: NVIDIA Corporation Device cb84 Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- 00:09.0 IDE interface: NVIDIA Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Biostar Microtech Int'l Corp Device 5407 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 09f0 [size=8] I/O ports at 0bf0 [size=4] I/O ports at 0970 [size=8] I/O ports at 0b70 [size=4] I/O ports at dc00 [size=16] Memory at fe02a000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Capabilities: [8c] SATA HBA v1.0 Capabilities: [b0] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: ahci 00:0b.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0c.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0d.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0e.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00008000-00008fff Memory behind bridge: fd800000-fd8fffff Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0f.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00007000-00007fff Memory behind bridge: fd600000-fd6fffff Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:10.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: fd400000-fd4fffff Prefetchable memory behind bridge: 00000000fd300000-00000000fd3fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:11.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fd200000-fd2fffff Prefetchable memory behind bridge: 00000000fd100000-00000000fd1fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 VGA compatible controller: NVIDIA Corporation C68 [GeForce 7050 PV / nForce 630a] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Biostar Microtech Int'l Corp Device 1406 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fb000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (64-bit, prefetchable) [size=256M] Memory at fc000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Kernel driver in use: nvidia Kernel modules: nvidia_current, nouveau, nvidiafb 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Subsystem: Biostar Microtech Int'l Corp Device 2305 Flags: bus master, fast devsel, latency 0, IRQ 47 I/O ports at ac00 [size=256] Memory at fdcff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Capabilities: [48] Vital Product Data Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] Express Endpoint, MSI 00 Capabilities: [84] Vendor Specific Information: Len=4c <?> Capabilities: [100] Advanced Error Reporting Capabilities: [12c] Virtual Channel Capabilities: [148] Device Serial Number 32-00-00-00-10-ec-81-68 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 sudo rfkill list all 2: phy2: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Delete eth0 avahi from the ifconfig list

  - by sai

  Hello this is the response I get from ifconfig. Now I have two eth0 things being showed up. I need to delete the second one which says eth0:avahi. I posted my ifconfig's response on a site as I has problem using wired internet, and they suggested to remove the eth0 avahi, to get internet. But I am a newbie to linux networking and have no idea how to delete this. response for ifconfig eth0 Link encap:Ethernet HWaddr 18:a9:05:22:cd:f9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:28 Base address:0x4000 eth0:avahi Link encap:Ethernet HWaddr 18:a9:05:22:cd:f9 inet addr:169.254.10.43 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:28 Base address:0x4000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:796 errors:0 dropped:0 overruns:0 frame:0 TX packets:796 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:64016 (64.0 KB) TX bytes:64016 (64.0 KB) wlan0 Link encap:Ethernet HWaddr 00:26:82:3c:ac:27 inet6 addr: fe80::226:82ff:fe3c:ac27/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:52142 errors:0 dropped:0 overruns:0 frame:0 TX packets:30404 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:60816983 (60.8 MB) TX bytes:4160159 (4.1 MB)

  Read the article

• WPA2 authentication fails using USB network devices (Linksys and Rosewill)

  - by Greg Youtz

  Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. Tried the same with a Linksys USB network adapter. Both failed to authenticate. Worth noting that I recently switched from Comcast to CenturyLink and so switched routers. The system connected successfully to previous router (Linksys EA4500) using WPA2. Would think it is the router (Actiontec C1000A) but all other devices (TV, iPad, Windows, Blackberry, and Squeezebox) connect ok. Would appreciate some diagnostic guidance and insight (phrased for a newbie!) Tests to date: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 00:e0:4d:30:40:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:ac00(size=256) memory:fdcff000-fdcfffff memory:fdb00000-fdb1ffff *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan1 serial: 00:02:6f:bd:30:a0 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.2.0-31-generic firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn sudo lspci -v 00:00.0 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: NVIDIA Corporation MCP67 ISA Bridge (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 00:01.1 SMBus: NVIDIA Corporation MCP67 SMBus (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: 66MHz, fast devsel, IRQ 11 I/O ports at fc00 [size=64] I/O ports at 1c00 [size=64] I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:01.2 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Flags: 66MHz, fast devsel 00:02.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:04.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:06.0 IDE interface: NVIDIA Corporation MCP67 IDE Controller (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Kernel driver in use: pata_amd Kernel modules: pata_amd 00:07.0 Audio device: NVIDIA Corporation MCP67 High Definition Audio (rev a1) Subsystem: Biostar Microtech Int'l Corp Device 820c Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:08.0 PCI bridge: NVIDIA Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: fd000000-fd0fffff Capabilities: [b8] Subsystem: NVIDIA Corporation Device cb84 Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- 00:09.0 IDE interface: NVIDIA Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Biostar Microtech Int'l Corp Device 5407 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 09f0 [size=8] I/O ports at 0bf0 [size=4] I/O ports at 0970 [size=8] I/O ports at 0b70 [size=4] I/O ports at dc00 [size=16] Memory at fe02a000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Capabilities: [8c] SATA HBA v1.0 Capabilities: [b0] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: ahci 00:0b.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0c.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0d.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0e.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00008000-00008fff Memory behind bridge: fd800000-fd8fffff Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0f.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00007000-00007fff Memory behind bridge: fd600000-fd6fffff Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:10.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: fd400000-fd4fffff Prefetchable memory behind bridge: 00000000fd300000-00000000fd3fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:11.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fd200000-fd2fffff Prefetchable memory behind bridge: 00000000fd100000-00000000fd1fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 VGA compatible controller: NVIDIA Corporation C68 [GeForce 7050 PV / nForce 630a] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Biostar Microtech Int'l Corp Device 1406 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fb000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (64-bit, prefetchable) [size=256M] Memory at fc000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Kernel driver in use: nvidia Kernel modules: nvidia_current, nouveau, nvidiafb 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Subsystem: Biostar Microtech Int'l Corp Device 2305 Flags: bus master, fast devsel, latency 0, IRQ 47 I/O ports at ac00 [size=256] Memory at fdcff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Capabilities: [48] Vital Product Data Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] Express Endpoint, MSI 00 Capabilities: [84] Vendor Specific Information: Len=4c <?> Capabilities: [100] Advanced Error Reporting Capabilities: [12c] Virtual Channel Capabilities: [148] Device Serial Number 32-00-00-00-10-ec-81-68 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 sudo rfkill list all 2: phy2: Wireless LAN Soft blocked: no Hard blocked: no Would appreciate insight on how to chase this down.

  Read the article

• Gnome-Network-Manager Config File Migration

  - by Jorge

  I think I have an issue with gnome-network-manager, I used to have a lot of connections configured, Wireless, Wired and VPN. After upgrading to 12.04 (from 11.10) I lost every configuration. I realized that the configs that used to be saved in $HOME/.gconf/system/networking/connections now are being saved in /etc/NetworkManager/system-connections/. I don't know how to migrate my settings to the new config file format Can anybody help me? jorge@thinky:~$ sudo lshw -C network *-network description: Ethernet interface product: 82566MM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:1f:e2:14:5a:9b capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k firmware=0.3-0 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:fe000000-fe01ffff memory:fe025000-fe025fff ioport:1840(size=32) *-network description: Wireless interface product: PRO/Wireless 4965 AG or AGN [Kedron] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 61 serial: 00:21:5c:32:c2:e5 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwl4965 driverversion=3.2.0-23-generic-pae firmware=228.61.2.24 ip=192.168.2.103 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:df3fe000-df3fffff jorge@thinky:~$ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04 LTS Release: 12.04 Codename: precise jorge@thinky:~$ uname -a Linux thinky 3.2.0-23-generic-pae #36-Ubuntu SMP Tue Apr 10 22:19:09 UTC 2012 i686 i686 i386 GNU/Linux jorge@thinky:~$ dpkg -l | grep -i firm ii linux-firmware 1.79 Firmware for Linux kernel drivers

  Read the article

• How do I get a rt2800usb wireless device working?

  - by Jii

  My brand new desktop running 13.04 has endless problems with wireless. Dozens of others are flooding forums with reports of the same problems. It worked fine for a few days, then there were a few days where it started having problems sometimes and working sometimes. Now it never works at all. I have 5+ devices all able to connect without any trouble at all, including iPhone, Android phone, 3DS, multiple game consoles, a laptop running windows 7, and even a second desktop machine running Ubuntu 12.04 sitting right behind the 13.04 machine. All other devices have full wireless bars displayed (strong signals). At any moment, one of the following is happening, and it changes randomly: Trying to connect forever, but never establishing a connection. Wireless icon constantly animating. Finds no wireless networks at all. (There are 12+ in range according to other devices.) Will not try to connect to the network. If I use the icon to connect, it will display "Disconnected" within a few seconds. Will continuously ask for the network password. Typing it in correctly does not help. Wireless is working fine. This happens sometimes. It can work for days at a time, or only 10 mins at a time. Various things that usually do nothing but sometimes fix the problem: Reboot. This has the best chance of helping, but it usually takes 5+ times. Disable/re-enable Wi-Fi using the wireless icon. Disable/re-enable Networking using the wireless icon. Use the icon to try and connect to a network (if found). Use the icon to open Edit Connections and delete my connection info, causing it to be recreated (once it's actually found again). Various things that seem to make no difference: Changing between using Linux headers in grub at bootup, between 3.10.0, 3.9.0, or 3.8.0. Move the wireless router very close to the desktop. Running sudo rfkill unblock all (I dunno what this is supposed to do.) I've used Ubuntu for 6 years and I've never had a problem with networking. Now I'm spending all my time reading through endless problem reports and trying all the answers. None of them have helped. I am doing this instead of getting work done, which is defeating the whole purpose of using Ubuntu. It's heartbreaking to be honest. In the current state of "no networks are showing up", here are outputs from the random things that other people are usually asked to run: lspic 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Lynx Point PCI Express Root Port #1 (rev d4) 00:1c.2 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 610] (rev a1) 01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1) 03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03) lsmod Module Size Used by e100 41119 0 nls_iso8859_1 12713 1 parport_pc 28284 0 ppdev 17106 0 bnep 18258 2 rfcomm 47863 12 binfmt_misc 17540 1 arc4 12573 2 rt2800usb 27201 0 rt2x00usb 20857 1 rt2800usb rt2800lib 68029 1 rt2800usb rt2x00lib 55764 3 rt2x00usb,rt2800lib,rt2800usb coretemp 13596 0 mac80211 656164 3 rt2x00lib,rt2x00usb,rt2800lib kvm_intel 138733 0 kvm 452835 1 kvm_intel cfg80211 547224 2 mac80211,rt2x00lib crc_ccitt 12707 1 rt2800lib ghash_clmulni_intel 13259 0 aesni_intel 55449 0 usb_storage 61749 1 aes_x86_64 17131 1 aesni_intel joydev 17613 0 xts 12922 1 aesni_intel nouveau 1001310 3 snd_hda_codec_hdmi 37407 1 lrw 13294 1 aesni_intel gf128mul 14951 2 lrw,xts mxm_wmi 13021 1 nouveau snd_hda_codec_realtek 46511 1 ablk_helper 13597 1 aesni_intel wmi 19256 2 mxm_wmi,nouveau snd_hda_intel 44397 5 ttm 88251 1 nouveau drm_kms_helper 49082 1 nouveau drm 295908 5 ttm,drm_kms_helper,nouveau snd_hda_codec 190010 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel cryptd 20501 3 ghash_clmulni_intel,aesni_intel,ablk_helper snd_hwdep 13613 1 snd_hda_codec snd_pcm 102477 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel btusb 18291 0 snd_page_alloc 18798 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 i2c_algo_bit 13564 1 nouveau snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30417 1 snd_seq_midi snd_seq 61930 2 snd_seq_midi_event,snd_seq_midi bluetooth 251354 22 bnep,btusb,rfcomm snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi lpc_ich 17060 0 snd_timer 29989 2 snd_pcm,snd_seq mei 46588 0 snd 69533 20 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device psmouse 97838 0 microcode 22923 0 soundcore 12680 1 snd video 19467 1 nouveau mac_hid 13253 0 serio_raw 13215 0 lp 17799 0 parport 46562 3 lp,ppdev,parport_pc hid_generic 12548 0 usbhid 47346 0 hid 101248 2 hid_generic,usbhid ahci 30063 3 libahci 32088 1 ahci e1000e 207005 0 ptp 18668 1 e1000e pps_core 14080 1 ptp sudo lshw -c network 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Lynx Point PCI Express Root Port #1 (rev d4) 00:1c.2 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-port SATA Controller 1 [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 610] (rev a1) 01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1) 03:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03) sudo iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on sudo iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results NOTE: This dmesg was done after a reboot where the network manager was continuously displaying the "disconnected" message over and over. So it must have been trying to connect at this time. My network was displayed in the list of options, as the only option despite other devices picking up 12+ access points. The router channel is set to auto. dmesg | tail -30 [ 187.418446] wlan0: associated [ 190.405601] wlan0: disassociated from 00:14:d1:a8:c3:44 (Reason: 15) [ 190.443312] cfg80211: Calling CRDA to update world regulatory domain [ 190.443431] wlan0: deauthenticating from 00:14:d1:a8:c3:44 by local choice (reason=3) [ 190.451635] cfg80211: World regulatory domain updated: [ 190.451643] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 190.451648] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 190.451652] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 190.451656] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 190.451659] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 190.451662] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 191.824451] wlan0: authenticate with 00:14:d1:a8:c3:44 [ 191.850608] wlan0: send auth to 00:14:d1:a8:c3:44 (try 1/3) [ 191.884604] wlan0: send auth to 00:14:d1:a8:c3:44 (try 2/3) [ 191.886309] wlan0: authenticated [ 191.886579] rt2800usb 3-5.3:1.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 191.886588] rt2800usb 3-5.3:1.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 191.889556] wlan0: associate with 00:14:d1:a8:c3:44 (try 1/3) [ 192.001493] wlan0: associate with 00:14:d1:a8:c3:44 (try 2/3) [ 192.040274] wlan0: RX AssocResp from 00:14:d1:a8:c3:44 (capab=0x431 status=0 aid=3) [ 192.044235] wlan0: associated [ 193.948188] wlan0: deauthenticating from 00:14:d1:a8:c3:44 by local choice (reason=3) [ 193.981501] cfg80211: Calling CRDA to update world regulatory domain [ 193.984080] cfg80211: World regulatory domain updated: [ 193.984082] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 193.984084] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 193.984085] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 193.984085] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 193.984086] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 193.984087] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) The router uses MAC filtering, and security is WPA PSK with cipher as auto. So, any ideas? Or is the solution just to not use 13.04 unless you have a wired connection? (I don't have this option.) If so, please just tell me straight. I survived 9.04 Jaunty, and I can survive 13.04 Raring. Update #1 Results from trying Wild Man's first answer: jii@conan:~$ echo "options rt2800usb nohwcrypt=y" | sudo tee /etc/modprobe.d/rt2800usb.conf options rt2800usb nohwcrypt=y jii@conan:~$ sudo modprobe -rfv rt2800usb rmmod rt2800usb rmmod rt2800lib rmmod crc_ccitt rmmod rt2x00usb rmmod rt2x00lib rmmod mac80211 rmmod cfg80211 jii@conan:~$ sudo modprobe -v rt2800usb insmod /lib/modules/3.10.0-031000-generic/kernel/lib/crc-ccitt.ko insmod /lib/modules/3.10.0-031000-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.10.0-031000-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2x00lib.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2800lib.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2x00usb.ko insmod /lib/modules/3.10.0-031000-generic/kernel/drivers/net/wireless/rt2x00/rt2800usb.ko nohwcrypt=y I tried: gksudo gedit /etc/pm/power.d/wireless but I didn't have the package. It said to install gksu. I tried that, but of course, not having Internet, I didn't get the package. So instead I did: sudo gedit /etc/pm/power.d/wireless Which created the file. Here is the body: #!/bin/sh /sbin/iwconfig wlan0 power off I then rebooted. No change. I tried adding exit 0 to the bottom of the wireless file, and rebooted. No change. Please note that this is a desktop machine. I'm assuming power management is primarily for laptops, but the iwconfig does state that power management is on, so who knows. The recommended router changes I did not do, since the current router settings are (I think) required for some of the older devices I have, and because the current settings work on all my modern devices including Ubuntu 12.04 and Windows 7. I do appreciate the advice though, and I'll look into it when I have time. Anything else to try? Update #2 I booted into Ubuntu 12.04.3 from a dvd, and the same problems exist. I have a separate old desktop machine with 12.04 installed that has no wireless problems at all. So obviously the problem is wireless hardware compatibility in both 12.04.03 LTS and 13.04. Update #3 The same problems exist even when using a wired connection. I plugged an ethernet cable directly to the router and the network manager added an "Auto Ethernet" entry, but it cannot establish a connection to it. So the problem is not specific to wireless. Meanwhile, I purchased a Trendnet N300 wireless USB adapter, TEW-664UB. I plugged it in, but I have no idea how to get Ubuntu to try and use it. Can anyone tell me how? Can I download a package on another computer and copy the .deb over to do an install, etc? I'm installing windows 7 to double check that the internet connection works there and it's not just some magically faulty hardware. Thanks for your help.

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• network manager says "device not managed"

  - by Daniella Glover

  I used to be able to share my network connection by editing the Auto Eth0 to share with other computers in the Ipv4 section and now I upgraded my laptop to 11.10 . Now are there no wired connections in the network manager. When I click my connections applet at the top of the tray it also says wired device not managed! when I type ifconfig -a daniella@daniella-1001HA:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 90:e6:ba:83:d6:fc UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 eth0:avahi Link encap:Ethernet HWaddr 90:e6:ba:83:d6:fc inet addr:169.254.13.40 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:45 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 00:25:d3:90:43:41 inet addr:192.168.0.6 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::225:d3ff:fe90:4341/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12881 errors:0 dropped:0 overruns:0 frame:0 TX packets:12867 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8851081 (8.8 MB) TX bytes:2343199 (2.3 MB)

  Read the article

• How do I install the EW-7318Ug wireless drivers?

  - by user69731

  I'm on Ubuntu 12.04 and I need to install & configure Internet connection. I want to use montor mode in Wireshark. After Ubuntu installation my wireless card was recognized but it doesn't connect to the Internet. Internal wireless card works well. What should I do? I'm new to Linux. PC:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 64:31:50:0f:d4:70 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x8000 eth1 Link encap:Ethernet HWaddr e0:2a:82:aa:2d:3e inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::e22a:82ff:feaa:2d3e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20978 errors:0 dropped:0 overruns:0 frame:364651 TX packets:20949 errors:171 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19299119 (19.2 MB) TX bytes:3024858 (3.0 MB) Interrupt:19 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4788 errors:0 dropped:0 overruns:0 frame:0 TX packets:4788 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:387017 (387.0 KB) TX bytes:387017 (387.0 KB) wlan1 Link encap:Ethernet HWaddr 00:1f:1f:44:c1:a4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10508 errors:0 dropped:0 overruns:0 frame:0 TX packets:6143 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14831319 (14.8 MB) TX bytes:644606 (644.6 KB) PC:~$ iwconfig lo no wireless extensions. wlan1 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:225 Noise level:162 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions.

  Read the article

• Wifi - wireless network not working after installing Ubuntu 12.04

  - by Nilesh

  I had installed ubuntu 12.04 in my Dell Vostro 3460. Initially wired as well wireless both are not working. After installing compat-wireless-2012-07-03-pc.tar.bz2 wired network fine but wireless is not working. Previously both were working fine with ubuntu 11.10. Also presently both network are working fine in Win7. lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.4 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 5 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 10) iwconfig: lo no wireless extensions. eth0 no wireless extensions. ifconfig: eth0 Link encap:Ethernet HWaddr 84:8f:69:d4:35:9b inet addr:10.24.22.72 Bcast:10.24.31.255 Mask:255.255.224.0 inet6 addr: fe80::868f:69ff:fed4:359b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15332 errors:0 dropped:0 overruns:0 frame:0 TX packets:10425 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:9262594 (9.2 MB) TX bytes:1572030 (1.5 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1432 errors:0 dropped:0 overruns:0 frame:0 TX packets:1432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145656 (145.6 KB) TX bytes:145656 (145.6 KB)

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• Trendnet tew-424ub wireless not working after update 12.10

  - by dwa

  I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

  Read the article

• Lost WiFi after 12.10 upgrade

  - by Steven Guillory

  I received my new Dell Vostro 2420 last week, and just got around to upgrading from 11.10 to 12.10. Unfortunately, like many others (after researching the issue), I no longer have WiFi. I have tried every sudo command given that worked for others, and still can't get my wireless to function. I am new to Linux, so any and all help is appreciated. Thanks in advance! Edit: I can connect via ethernet, just not via wifi. As a matter of fact, when I use Fn + F2 to turn on wifi, only my bluetooth comes on. lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 07:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) This is what I am getting... dpkg: error: --install needs at least one package archive file argument Type dpkg --help for help about installing and deinstalling packages [*]; Use dselect or aptitude for user-friendly package management; Type dpkg -Dhelp for a list of dpkg debug flag values; Type dpkg --force-help for a list of forcing options; Type dpkg-deb --help for help about manipulating *.deb files; Options marked [*] produce a lot of output - pipe it through less or more !

  Read the article

< Previous Page | 24 25 26 27 28 29 30 31 32 33 34 35  | Next Page >