Search Results

Search found 12992 results on 520 pages for 'password recovery'.

Page 280/520 | < Previous Page | 276 277 278 279 280 281 282 283 284 285 286 287  | Next Page >

• fd partitions gone from 2 discs, md happy with it and resyncs. How to recover ?

  - by d0nd

  Hey gurus, need some help badly with this one. I run a server with a 6Tb md raid5 volume built over 7*1Tb disks. I've had to shut down the server lately and when it went back up, 2 out of the 7 disks used for the raid volume had lost its conf : dmesg : [ 10.184167] sda: sda1 sda2 sda3 // System disk [ 10.202072] sdb: sdb1 [ 10.210073] sdc: sdc1 [ 10.222073] sdd: sdd1 [ 10.229330] sde: sde1 [ 10.239449] sdf: sdf1 [ 11.099896] sdg: unknown partition table [ 11.255641] sdh: unknown partition table All 7 disks have same geometry and were configured alike : dmesg : Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect All 7 disks (sdb1, sdc1, sdd1, sde1, sdf1, sdg1, sdh1) were used in a md raid5 xfs volume. When booting, md, which was (obviously) out of sync kicked in and automatically started rebuilding over the 7 disks, including the two "faulty" ones; xfs tried to do some shenanigans as well: dmesg : [ 19.566941] md: md0 stopped. [ 19.817038] md: bind<sdc1> [ 19.817339] md: bind<sdd1> [ 19.817465] md: bind<sde1> [ 19.817739] md: bind<sdf1> [ 19.817917] md: bind<sdh> [ 19.818079] md: bind<sdg> [ 19.818198] md: bind<sdb1> [ 19.818248] md: md0: raid array is not clean -- starting background reconstruction [ 19.825259] raid5: device sdb1 operational as raid disk 0 [ 19.825261] raid5: device sdg operational as raid disk 6 [ 19.825262] raid5: device sdh operational as raid disk 5 [ 19.825264] raid5: device sdf1 operational as raid disk 4 [ 19.825265] raid5: device sde1 operational as raid disk 3 [ 19.825267] raid5: device sdd1 operational as raid disk 2 [ 19.825268] raid5: device sdc1 operational as raid disk 1 [ 19.825665] raid5: allocated 7334kB for md0 [ 19.825667] raid5: raid level 5 set md0 active with 7 out of 7 devices, algorithm 2 [ 19.825669] RAID5 conf printout: [ 19.825670] --- rd:7 wd:7 [ 19.825671] disk 0, o:1, dev:sdb1 [ 19.825672] disk 1, o:1, dev:sdc1 [ 19.825673] disk 2, o:1, dev:sdd1 [ 19.825675] disk 3, o:1, dev:sde1 [ 19.825676] disk 4, o:1, dev:sdf1 [ 19.825677] disk 5, o:1, dev:sdh [ 19.825679] disk 6, o:1, dev:sdg [ 19.899787] PM: Starting manual resume from disk [ 28.663228] Filesystem "md0": Disabling barriers, not supported by the underlying device [ 28.663228] XFS mounting filesystem md0 [ 28.884433] md: resync of RAID array md0 [ 28.884433] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [ 28.884433] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. [ 28.884433] md: using 128k window, over a total of 976759936 blocks. [ 29.025980] Starting XFS recovery on filesystem: md0 (logdev: internal) [ 32.680486] XFS: xlog_recover_process_data: bad clientid [ 32.680495] XFS: log mount/recovery failed: error 5 [ 32.682773] XFS: log mount failed I ran fdisk and flagged sdg1 and sdh1 as fd. I tried to reassemble the array but it didnt work: no matter what was in mdadm.conf, it still uses sdg and sdh instead of sdg1 and sdh1. I checked in /dev and I see no sdg1 and and sdh1, shich explains why it wont use it. I just don't know why those partitions are gone from /dev and how to readd those... blkid : /dev/sda1: LABEL="boot" UUID="519790ae-32fe-4c15-a7f6-f1bea8139409" TYPE="ext2" /dev/sda2: TYPE="swap" /dev/sda3: LABEL="root" UUID="91390d23-ed31-4af0-917e-e599457f6155" TYPE="ext3" /dev/sdb1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdc1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdd1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sde1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdf1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdg: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdh: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" fdisk -l : Disk /dev/sda: 40.0 GB, 40020664320 bytes 255 heads, 63 sectors/track, 4865 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8c878c87 Device Boot Start End Blocks Id System /dev/sda1 * 1 12 96358+ 83 Linux /dev/sda2 13 134 979965 82 Linux swap / Solaris /dev/sda3 135 4865 38001757+ 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc9bdc1e9 Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xcc356c30 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xe87f7a3d Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xb17a2d22 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdg: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8f3bce61 Device Boot Start End Blocks Id System /dev/sdg1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdh: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa98062ce Device Boot Start End Blocks Id System /dev/sdh1 1 121601 976760001 fd Linux raid autodetect I really dont know what happened nor how to recover from this mess. Needless to say the 5TB or so worth of data sitting on those disks are very valuable to me... Any idea any one? Did anybody ever experienced a similar situation or know how to recover from it ? Can someone help me? I'm really desperate... :x

  Read the article

• Free way to share large files over the internet.

  - by vaccano

  I need to send a approximately 50MB zip file. My email provider will not allow me to send attachments that big. Is there a free service out there that I can upload my file to and allow someone else a password to download it?

  Read the article

• Cloning hard drive -- data, operating system settings, everything

  - by Salman A

  I am using Windows XP. My hard drive (Seagate 160gig Barracuda) is about to fail. Its already developed bad sectors and it seems to get worse everyday. Data transfer mode is down to PIO mode 2, chkdsk runs every now and then, registry and important windows files get corrupted and I spend 30-60 minutes running chkdsk /f /r from the recovery console. I've got a replacement (Seagate 5000gig Barracuda) and now i want to transfer each and every thing on to the new drive. I don't want to go through windows and software installation, I spent ages getting all those software installed and configured on that hard drive. Need advice: whats the best way to transfer everything onto the new drive so that it behaves just like the old one. And are there any "gotchas".

  Read the article

• JNDI Datasource Problem on Tomcat 6, Hibernate

  - by Asuman AKYILDIZ

  Hello; I am using Tomcat 6 as application server, Struts-Hibernate and MyEclipse 6.0. My application uses JDBC driver but I should modify it to use JNDI Datasource. I followed steps as described in tomcat 6.0 howto tutorial. I defined my resource in tomcatconf: <Resource name="jdbc/ats" global="jdbc/ats" auth="Container" type="javax.sql.DataSource" driverClassName="oracle.jdbc.OracleDriver" url="jdbc:oracle:thin:@//localhost:1521/MISDEV" username="TEST" password="TEST" maxActive="20" maxIdle="10" maxWait="-1" validationQuery="SELECT 1 from dual" removeAbandoned="true" removeAbandonedTimeout="30" logAbandoned="false"/> I gave reference in my application web.xml: <resource-ref> <description>Oracle Datasource example</description> <res-ref-name>jdbc/ats</res-ref-name> <res-type>javax.sql.DataSource</res-type> <res-auth>Container</res-auth> </resource-ref> And I defined datasource-dialect in my hibernate-cfg.xml <property name="connection.datasource">java:comp/env/jdbc/ats</property> <property name="dialect">org.hibernate.dialect.Oracle9Dialect</property> But when I create hibernate session, it can not open the connection: 09:18:11,322 ERROR JDBCExceptionReporter:72 - Connections could not be acquired from the underlying database! org.hibernate.exception.GenericJDBCException: Cannot open connection I also tried to set the properties at runtime: Configuration configuration = new Configuration(); configuration.setProperty("hibernate.dialect", "org.hibernate.dialect.Oracle9Dialect"); //configuration.setProperty("hibernate.connection.datasource", "java:comp/env/jdbc/ats"); configuration.setProperty("hibernate.current_session_context_class", "thread"); configuration.setProperty("hibernate.connection.provider_class", "org.hibernate.connection.C3P0ConnectionProvider"); configuration.setProperty("hibernate.show_sql", "true"); sessionFactory = configuration.configure().buildSessionFactory(); It does not open connection again. But, when I use JDBC driver it works: Configuration configuration = new Configuration(); configuration.setProperty("hibernate.dialect", "org.hibernate.dialect.Oracle9Dialect"); //configuration.setProperty("hibernate.connection.datasource", "java:comp/env/jdbc/ats"); configuration.setProperty("hibernate.connection.url", "jdbc:oracle:thin:@//localhost:1521/MISDEV"); configuration.setProperty("hibernate.connection.username", "test"); configuration.setProperty("hibernate.connection.password", "test"); configuration.setProperty("hibernate.connection.driver_class", "oracle.jdbc.OracleDriver"); configuration.setProperty("hibernate.transaction.factory_class", "org.hibernate.transaction.JDBCTransactionFactory"); configuration.setProperty("hibernate.current_session_context_class", "thread"); configuration.setProperty("hibernate.connection.provider_class", "org.hibernate.connection.C3P0ConnectionProvider"); configuration.setProperty("hibernate.show_sql", "true"); sessionFactory = configuration.configure().buildSessionFactory(); I have been searching for 3 days and no success. What may be de problem?

  Read the article

• Unable to clone repository with Git

  - by kim3er

  I am trying to clone a repository on my machine that I have just created on GitHub. I am new to Git, but have been using SVN for a while. I've set up an RSA key as per instructions but am unable to clone with either the SSH or HTTP Urls. When I use HTTP, I get the following error: Password: fatal: Out of memory, realloc failed I'm using Windows 7 with MSysGit (using Bash & PuTTY).

  Read the article

• Virtualised Sharepoint Backup Strategies

  - by dunxd

  I have a Sharepoint (OSS 2007) farm running on three virtual machines in VMWare ESX, plus a SQL Server backend on physical hardware. During a recent Business Continuity Planning event I tried restoring the sharepoint farm with only the config and content databases, and failed to get things working. My plan was to build a new sharepoint server, then attach this to a restoration config database and install the Central Management site on this server, then reattach the content databases. This failed at the Central Management part of the plan. So I am back to the drawing board on the best strategy for backup and recovery, with reducing the time and complexity of the restore job the main objective. I haven't been able to find much in the way of discussion of backup/restore strategies for Sharepoint in a VMWare environment, so I figured I'd see if anyone on server fault has any ideas or experience.

  Read the article

• Can't access a partion that has a virus on it

  - by vaccano

  My wife's computer had a virus alarm go off, so I am looking into it. The virus is supposed to be on the D: drive. I wanted to talk a quick look at the file, but I cannot not. It has one file that I can get to. It is D:\Recovery. That shows a "Protected by PC Angel" graphic. How can I get past this? Should I do it? Is the virus scanner wrong? (I am using Avast).

  Read the article

• MMC not strating in window server 2003

  - by Mirage

  I have window 2003 server with AD installed. The file server is used to share the folder acroos network. However after 1 hour suddenlt i can't access my shares , it asks me the password and then when i enter it it does not allow me and say access denied. Then i try mmc.exe on server it say The application has failed to start because MS.dll was not loaded How can i fix the problem. Can i re-install the MMC

  Read the article

• Way to connect to VPS w/Win Vista Home Basic, other than VNC or TeamViewer?

  - by Tia Peterson

  I need to connect to a VPS and I'm running Vista Home Basic. TightVNC and TeamViewer both require access to the VPS first, because they require that the server be set up with TightVNC or TeamViewer. Is there anything similar to Remote Desktop that will allow me to use the IP address and administrator password to the VPS to simply connect, rather than having to have the hosting company set up VNC or TeamViewer on the server first? Any help would be appreciated!!! Thank you!

  Read the article

• keepass not working with wine

  - by Decio Lira

  I installed Keepass 1.16 in my thumbdrive, which reportedly works with wine (as per Keepass homepage), but after entering the master password it just hangs and shows the "The program keepass has encountered a serious problem and needs to close" screen. I got this error msg among the stack trace on the terminal: wine: Call from 0x7b844633 to unimplemented function bcrypt.dll.BCryptOpenAlgorithmProvider, aborting On windows, everything runs fine. I'm using wine-1.1.27 on ubuntu 9.04 Any thoughts?

  Read the article

• Guaranteeing ACID properties for InnoDB databases.

  - by plinehan

  What steps must one take to ensure that an otherwise defaultly-configured InnoDB server is truly ACID compliant? The InnoDB configuration page mentions that the hardware itself must be configured to honor fsync calls, i.e. disable any write-back caches. This page mentions some other concerns, but may be conflating the binary log and the InnoDB log, and may be a bit out of date regarding default settings for MySQL 5.x. Upon reading the binary log document page it would seem that the "sync_binlog=1" setting is not required for ACID properties in general, only for ACID properties vis a vis point-in-time recovery and replication. So, is disabling write-back disk caching sufficient, or are there other settings that must be tweaked?

  Read the article

• Can't install Windows 7 on Acer Aspire M1100

  - by r0ca

  When I install Windows 7, everything goes smooth but as soon as it's done and Windows needs to reboot for the last time before getting the desktop, the computer stucks to Verify DMI Pool Data............. and then, nothing. I change the CMOS battery, I tried so many setup in BIOS, even load default settings... Nothing worked. The HDD light is not flickering anymore, no HDD activity. CTRL-ALT-DEL doesn't work. It's just impossible to load Windows 7. I tried Windows XP and this works fine. I also tried the Acer (Futureshop) recovery CD and I get an Hexademical error message stating the install cannot continue. Is there a BIOS flash apps somewhere or a fix I can apply to have Windows 7 Ultimate installed on my computer. Any takers?

  Read the article

• i have a network of PC's and some macs.

  - by user292569

  i have security problems with the macs, they can auto login on the server when i want it to ask for a user name and password. anyone can just get on the computer and sign into the last person who was using it. any help?

  Read the article

• i have a network of PC's and some macs.

  - by user292569

  i have security problems with the macs, they can auto login on the server when i want it to ask for a user name and password. anyone can just get on the computer and sign into the last person who was using it. any help?

  Read the article

• Exchange 2010: Merge a mailbox between two users

  - by Mestika

  Hi, I have two users in my Exchange 2010 server where one user no longer is employed but we need access to the mails. I cannot find any function to reset the users password so my question is if it is possible to merge the users mailbox into another users? Sincerely Mestika

  Read the article

• How to install MySQL on Windows 7

  - by akash gupta

  Please help me how to install MySQL on Windows 7. When I tried to install, I am getting errors as: The security settings could not be applied to the database because the connection has failed of the following errors ERROR NR:1045 Access denied for user 'root@'localhost(using password yes). I tried to uninstall MySQL completely and install again, but it shows this error again and again. I have changed my firewall setting also and tried unstalling antivirus sotware too. But it also did not work.

  Read the article

• Virtual Box Headless Mode: How can I get VRDP server to work with authentication?

  - by Andrew J. Brehm

  I tried this both on Windows 7 and Snow Leopard (Mac OS X 10.6). While vrdpauthtype null works (everyone can connect to VMs without user name/password) vrdpauthtype external doesn't work (and RDC connections are just rejected). Did anyone ever get this to work?

  Read the article

• Can't use sudo on ubuntu

  - by martin.malek

  After update and reboot I get 'user is not in the sudoers file. This incident will be reported.' when trying to call sudo. The problem is that I don't have a GRUB with revovery option. I try to boot from live cd but I'm not able to access the system partition, only the partition with grub. Can I somehow enable the recovery mode in GRUB? Or boot throw the live CD from first hard drive with some option for that?

  Read the article

• How to use nginx to proxy to a host requiring authentication?

  - by bwizzy

  How can I setup an nginx proxy_pass directive that will also include HTTP Basic authentication information sent to the proxy host? This is an example of the URL I need to proxy to: http://username:[email protected]/export?uuid=1234567890 The end goal is to allow 1 server present files from another server (the one we're proxying to) without exposing the URI of the proxy server. I have this working 90% correct now from following the Nginx config found here: http://kovyrin.net/2010/07/24/nginx-fu-x-accel-redirect-remote/ I just need to add in the HTTP Basic authentication to send to the proxy server

  Read the article

• Convert word to "JPEG-like" pdf file

  - by Chheang

  I've got a word document I'm trying to save to an uneditable, unselectable PDF file. Essentially, I'd like it to look like a JPEG, but in PDF format. I'm trying to avoid "printing to tiff, THEN printing to PDF." I'd prefer to go directly from Word to PDF. Additionally, I don't want to add a Password or anything. Does an option exist for this? Thanks!

  Read the article

• Solaris to Linux conversion: Use VxFS or GFS?

  - by w00t

  We're a Solaris shop looking at RedHat Enterprise Linux and one of the things we're wondering is if we should keep Veritas Volume Manager + FileSystem or go with LVM+ext3 or RedHat's preferred cluster filesystem solution, GFS. One of the things we like about Veritas is that it can use Veritas Volume Replicator to have a remote copy of important filesystems. This functionality seems to be missing from RedHat, DRBD doesn't seem to be packaged in RHEL... So my questions are: Does anybody use VxFS/VxVM/VVR on Linux? Thoughts, experiences? Comparison with LVM+ext3? Anybody using GFS? Thoughts, experiences? Do you do remote replication for disaster recovery, and if so, how? Is there a standard RedHat way?

  Read the article

• Ubuntu 10.04 doesn't accept keyboard input when running under VMware on Windows 7

  - by anwar

  I have just installed Ubuntu for the first time using VMWare on Windows 7. Everything has been installed smoothly but after the installation in the login screen username is coming and when I try to enter password it is not taking any input, keyboard is not working at all. After moving away from Ubuntu keyboard and everthing else is working fine. Does anyone know what's the cause behind this ?

  Read the article

• Stability, x86 Vs Sparc

  - by Jason T

  Our project are plan to migrate from Sparc to x86, and our HA requirement is 99.99%, previous on Sparc, we assume the hardware stability would like, hardware failure every 4 month or even one year, and also we have test data for our application, then we have requirement for each unplanned recovery (fail over) to achieve 99.99% (52.6 minutes unplanned downtime per year). But since we are going to use Intel x86, it seems the hardware stability is not so good as Sparc, but we don't have the detail data. So compare with Sparc, how about the stability of the Intel x86, should we assume we have more unplanned downtime? If so, how many, double? Where I can find some more detail of this two type of hardware?

  Read the article

• Script or Batch File to Automate Logon from Welcome Screen

  - by Guy Thomas

  Is there a script or batch file to automate the log-on process from the XP Welcome screen? As all details are the same Username, Password, and Domain in a room of 30 machines. The reason I don't use Windows AutoAdminLogon is I only want to logon temporary at different times as a user to run such things as online test for a class of high school students without the students logging on individually first, also it would be useful for admin tasks if I can change/specify the user details.

  Read the article

• Selectively Remove Auto Complete Entries from Internet Explorer

  - by Kanini

  Hello...I use Windows XP with IE 8. When I try to access GMail (or any other site for that matter), the Auto Complete feature shows the list of username and on select of that, it auto-completes the password as well. Is there a way, I can selectively remove one or two of the entries alone without having to delete all of Auto Complete entries? PS: Ofcourse, I do know about In-Private browsing and that it can be used for ensuring that a History is not left behind and ...

  Read the article

< Previous Page | 276 277 278 279 280 281 282 283 284 285 286 287  | Next Page >