Search Results

Search found 8989 results on 360 pages for 'response'.

Page 280/360 | < Previous Page | 276 277 278 279 280 281 282 283 284 285 286 287  | Next Page >

• Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

  - by Ron Whites

  Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

  Read the article

• Redirection of outbound UDP port.

  - by pboin

  For my residential service, I changed ISPs to Zoom/Armstrong. Just after that, my NTP daemons stopped working. I dug deep and diagnosed the problem: Unprivileged ports are getting out. When i run 'ntpdate' for example, I go out on a high, unprivleged port, and get a response on UDP 123. That's fine. The 'ntpd' daemon though, expects to go out on 123 and get its reply there as well. This must be a common problem, because it's directly addressed in the NTP troubleshooting guide. Just to see what would happen, I wrote a detailed email to the general support address at Armstrong. They replied almost immediately with a complete technical answer! They have everything <1024 blocked, except for a few ports to support outbound VPN. So, the question: Can I use IPtables to essentially re-write my outbound UDP 123 up to 2123 or something like that? If I do, does there need to be a corresponding 2123-123 rule to translate the reply? This seems like NAT, but with ports, not addresses. I tried, but can't seem to get iptables to do what I want. I'm not sure if it's my lack of skill, or if I'm trying the wrong solution. True, I could run ntpdate from cron, but that loses all of the adjustment smarts of NTP.

  Read the article

• Exchange - inbound email only works from some servers

  - by Kryptonite

  I am having a problem where inbound mail from outside only works when sent from certain hosts. For example, when I send myself an email from my personal gmail account all is well, as the logs show: 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 EHLO 250 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 STARTTLS 220 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 STARTTLS 220 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 EHLO 250 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 MAIL 250 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 RCPT 250 - - 2012-09-05 18:14:48 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 QUIT 240 - - However, if I sent from my personal Yahoo account, I get this response: Sorry, we were unable to deliver your message to the following address. <[email protected]>: Remote host said: 530 5.7.0 Must issue a STARTTLS command first [MAIL_FROM] (NB: Nothing appeared in the smtp log for this message.) Any suggestions where to start looking? EDIT ---- I don't know if it matters, but the certificate I am using for TLS is self signed.

  Read the article

• Reliable router with good VPN and WAN Throughput [closed]

  - by Asdande

  I have 2 cisco rv180 VPN router. These routers are giving me lots of problems. The webpages wont load correctly, slow response to load webpages plus other many issues. I have several cases pending with cisco. I give up on these routers. I would like to know if you guys can recommend me a reliable router for our 3 branches (NY - main, SC and FL). In NY- main office, we have 55 users. In SC branch, 6 users. In Florida we only have 1 (will grow soon). I need a router capable of support: 3 VPNs Site-to-Site connection VPN throughput of at least 40-50 Mbps WAN throughput at least 100 Mpbs and up PPTP Server for at least 5 PPTP users Web filtering - all users need access to internet Good Firewall Port forwarding for FTP Server - able to show the public IPs of FTP users (rv180 cannot do that, just shows me router's LAN interface IP, opened a case with cisco, now escaleted to level 2, still no answer or workaround) Dual WAN ports for balance or backup internet. Gigabit WAN/LAN ports Price between $400-$500 range. I was thinking on the TP-LINK TL-ER6120 or TL-ER6020 according to the review on smallnetbuilder.com http://www.smallnetbuilder.com/lanwan/lanwan-reviews/31983-tp-link-tl-er6020-safestream-gigabit-dual-wan-vpn-router-reviewed but I don't want to make another mistake as I did when I bought the cisco RV180. Thank you in advance,

  Read the article

• How can I implement ansible with per-host passwords, securely?

  - by supervacuo

  I would like to use ansible to manage a group of existing servers. I have created an ansible_hosts file, and tested successfully (with the -K option) with commands that only target a single host ansible -i ansible_hosts host1 --sudo -K # + commands ... My problem now is that the user passwords on each host are different, but I can't find a way of handling this in Ansible. Using -K, I am only prompted for a single sudo password up-front, which then seems to be tried for all subsequent hosts without prompting: host1 | ... host2 | FAILED => Incorrect sudo password host3 | FAILED => Incorrect sudo password host4 | FAILED => Incorrect sudo password host5 | FAILED => Incorrect sudo password Research so far: a StackOverflow question with one incorrect answer ("use -K") and one response by the author saying "Found out I needed passwordless sudo" the Ansible docs, which say "Use of passwordless sudo makes things easier to automate, but it’s not required." (emphasis mine) this security StackExchange question which takes it as read that NOPASSWD is required article "Scalable and Understandable Provisioning..." which says: "running sudo may require typing a password, which is a sure way of blocking Ansible forever. A simple fix is to run visudo on the target host, and make sure that the user Ansible will use to login does not have to type a password" article "Basic Ansible Playbooks", which says "Ansible could log into the target server as root and avoid the need for sudo, or let the ansible user have sudo without a password, but the thought of doing either makes my spleen threaten to leap up my gullet and block my windpipe, so I don’t" My thoughts exactly, but then how to extend beyond a single server? ansible issue #1227, "Ansible should ask for sudo password for all users in a playbook", which was closed a year ago by mpdehaan with the comment "Haven't seen much demand for this, I think most people are sudoing from only one user account or using keys most of the time." So... how are people using Ansible in situations like these? Setting NOPASSWD in /etc/sudoers, reusing password across hosts or enabling root SSH login all seem rather drastic reductions in security.

  Read the article

• nginx redirect what is not coming from load balancing

  - by dawez

  I have nginx on SERVER1 that is acting as load balancing between SERVER1 and SERVER2 in SERVER1 I have the upstreams for the load balancing defined as : upstream de.server.com { # similar upstreams defined also for other languages # SELF SERVER1 server 127.0.0.1:8082 weight=3 max_fails=3 fail_timeout=2; # other SERVER2 server otherserverip:8082 max_fails=3 fail_timeout=2; } The load balancing config on SERVER1 is this one: server { listen 80; server_name ~^(?<LANG>de|es|fr)\.server\.com; location / { proxy_pass http://$LANG.server.com; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; # trying to pass a variable in the header to SERVER2 proxy_set_header Is-From-Load-Balancer 1; } } Then in server 2 I have: server { listen 8082; server_name localhost; root /var/www/server.com/public; # test output values add_header testloadbalancer $http_is_from_load_balancer; add_header testloadbalancer2 not_load_bal; ## other stuff here to process the request } I can see the "testloadbalancer" in the response header is set to 1 when the request is coming from the load balancing, it is not present when from a direct access: SERVER2:8082 . I would like to bounce back to the SERVER1 all the direct requests that are sent to SERVER2, but keep the ones from the load balancing. So this should forbid direct access to SERVER2:8082 and redirect to SERVER1:80 .

  Read the article

• Server slowdown

  - by Clinton Bosch

  I have a GWT application running on Tomcat on a cloud linux(Ubuntu) server, recently I released a new version of the application and suddenly my server response times have gone from 500ms average to 15s average. I have run every monitoring tool I know. iostat says my disks are 0.03% utilised mysqltuner.pl says I am OK other see below top says my processor is 99% idle and load average: 0.20, 0.31, 0.33 memory usage is 50% (-/+ buffers/cache: 3997 3974) mysqltuner output [OK] Logged in using credentials from debian maintenance account. -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.63-0ubuntu0.10.04.1-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 370M (Tables: 52) [--] Data in InnoDB tables: 697M (Tables: 1749) [!!] Total fragmented tables: 1754 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 19h 25m 41s (1M q [28.122 qps], 1K conn, TX: 2B, RX: 1B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 1.0G global + 2.7M per thread (500 max threads) [OK] Maximum possible memory usage: 2.4G (30% of installed RAM) [OK] Slow queries: 0% (1/1M) [OK] Highest usage of available connections: 34% (173/500) [OK] Key buffer size / total MyISAM indexes: 16.0M/279.0K [OK] Key buffer hit rate: 99.9% (50K cached / 40 reads) [OK] Query cache efficiency: 61.4% (844K cached / 1M selects) [!!] Query cache prunes per day: 553779 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 34K sorts) [OK] Temporary tables created on disk: 4% (4K on disk / 102K total) [OK] Thread cache hit rate: 84% (185 created / 1K connections) [!!] Table cache hit rate: 0% (256 open / 27K opened) [OK] Open file limit used: 0% (20/2K) [OK] Table locks acquired immediately: 100% (692K immediate / 692K locks) [OK] InnoDB data size / buffer pool: 697.2M/1.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) table_cache (> 256)

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup.

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• How can I stop SipVicious ('friendly-scanner') from flooding my SIP server?

  - by a1kmm

  I run an SIP server which listens on UDP port 5060, and needs to accept authenticated requests from the public Internet. The problem is that occasionally it gets picked up by people scanning for SIP servers to exploit, who then sit there all day trying to brute force the server. I use credentials that are long enough that this attack will never feasibly work, but it is annoying because it uses up a lot of bandwidth. I have tried setting up fail2ban to read the Asterisk log and ban IPs that do this with iptables, which stops Asterisk from seeing the incoming SIP REGISTER attempts after 10 failed attempts (which happens in well under a second at the rate of attacks I'm seeing). However, SipVicious derived scripts do not immediately stop sending after getting an ICMP Destination Host Unreachable - they keep hammering the connection with packets. The time until they stop is configurable, but unfortunately it seems that the attackers doing these types of brute force attacks generally set the timeout to be very high (attacks continue at a high rate for hours after fail2ban has stopped them from getting any SIP response back once they have seen initial confirmation of an SIP server). Is there a way to make it stop sending packets at my connection?

  Read the article

• How to create an GUI that communicate with the USB Devices using win32 programming [migrated]

  - by VINAYAK

  I am doing my Project using win 32 programming.I am just learning about win32 programming and able to create an UI.I want to communicate with an USB Device with that UI.SO,How can i go for that?Is there any predefined functions will be there are we need to create the function for communicating with the OS and get the devices List and got the details about them. My purpose is to , 1.Creating an UI that tells about the Basic information about the device(We want to send a control request to the device to get the descriptors). 2.For that first of all i want to communicate with the OS for device attachment.That will lead to get the information about the device and Enumeration takes place and then only i request the device information through descriptors by using standard Requests. 3.And also i want to create the driver for my device.That will also need to achieve for communicating with OS(Windows). So,can anyone help me about this?How can i achieve this or approach this? Note: I am at the entry level now so anyone give response will be in a detailed format like step by step process would be appreciable.

  Read the article

• How do I lower the hardware volume? (volume too high)

  - by Zom-B

  I have a 4yo Dell laptop with Windows XP Pro (modern ones unfortunately don't have a physical volume knob), and lately I'm using my Apple earphones, because they have much better low frequency response than my $10 earphones. They also have the side effect of being much louder. To give an indication of my agony, for most tasks (movie, music, games) I have my main volume at 3 ticks: drag to 0 with the mouse and press the up key 3 times (the handle does not even raise 1 pixel) and my wave volume at 50%. I notice that when I do this, I have a lot of digital noise, because I'm using just a tiny fraction of the 16-bit space. If I drag the Wave slider down until I barely hear the audio, it becomes really distorted and noisy, indicating that this is digital volume (in the DirectSound driver or something) and not hardware volume. I experimented in Audition. When I make a tone of 1000Hz at -50db, (all windows volumes at max) the volume is just below my pain threshold. When I zoom in to see how high the sample values reach, I see that just 8 of the 16 bits are used (about -100 ~ 100). When I generate such tone at -80db (minimum I can specify) then I can still clearly hear the tone, although really noisy. When I zoom in, I see that just 3 out of 16 bits are used. I created a squarewave tone that is just 1 bit high, and I can still hear it! For most uses, this is not a big problem (audiophiles will disagree!), as I just have more noise than usual (about the same as old 8 bit hardware), but I'm also in the process of programming a hearing test program, in which case this problem is a death blow as the test subjects will even hear tones at the bottom of the theoretical range (lowering the windows volume is futile, see above) (I cannot update drivers, as Dell has discontinued XP support for my model)

  Read the article

• What can I do to determine the root cause of a Windows server hanging/freezing?

  - by Aaronaught

  We set up a new server here a few weeks ago that I am informally responsible for managing. Almost everything works perfectly except for one thing: Every so often it hangs without warning. To clarify: When I say hangs, I mean completely. None of the services respond and I'm unable to even get onto a local console - the display acts as though there's no VGA signal. One time, the server actually responded to pings, another time I got the "destination host unreachable" response, but most of the time the pings just time out, as one would expect for a hung server. Event logs don't show anything after a reboot. I don't mean that they don't show anything interesting, I mean that they don't show anything at all from before the failure occurs to after the reboot. And there are never any performance problems, strange errors, or other obvious signs of impending doom before it happens. I don't expect any easy answers here. What I'd like to know his I can methodically determine the root cause of this problem, be it a misbehaving service, defective hardware, or something else. Is there any kind of logging I can set up that will help me get to the bottom of this? Any hardware diagnostics or remote monitoring? Anything else I can do to help me discover what's actually happening, or at least be able to eliminate what isn't wrong? Just to reiterate, I really don't want to start speculating about possible causes and take a trial-and-error approach, because it's going to be at least several days at a time before I would have conclusive results. I'm looking for solutions to reliably trace the problem to its source.

  Read the article

• Measure Upload Speed between a client and our server

  - by tresstylez

  We host a SAAS application specially customized for multiple clients. For one customer in particular -- they are reporting sporadic performance issues from various locations on their network, in particular UPLOADING documents through a form on our website. The client claims they have "bandwidth to spare" and that utilization of their "pipe" is so low that it MUST be our application, but our application has MANY clients and all features are working fine for all other clients. Interestingly enough -- DOWNLOADS (ie. just accessing the website, or downloading documents) is working fine. Speed test shows that they should get 1.2Mbps UP. So, a 3MB file should take 20 secs to upload. It takes 60+ seconds on their network. Sometimes even small files take OVER 10 minutes to upload or they timeout. Pings and Traceroutes don't show any abnormally long hops or response times. They claim other SAAS applications they use allow them to upload just fine. Both IT teams are working together to resolve this issue. What kind of data can I request from the clients to begin ruling things out. Seems like we need to somehow measure LATENCY of the networks involved or even at the switch level, we need to understand if packets are getting dropped somewhere and why. Where should I start? Any help is appreciated. I'll provide more info upon requests

  Read the article

• PhpMyAdmin 500 Internal Server Error on Nginx/php5-fpm/Debian

  - by ThrownAway

  I downloaded PhpMyAdmin a while ago and am having a hard time getting it to work. Requesting localhost/phpmyadmin gives a 500 Internal Server Error response, but there's nothing in the error log. These are the steps I did: Downloaded the newest phpmyadmin and unzipped all the files to /var/vhosts/phpmyadmin/www/ Created a new php5-fpm pool and a server block on nginx Changed the owner of all the files inside phpmyadmin/ Tried requesting localhost/phpmyadmin and localhost/phpmyadmin/setup The phpmyadmin is running inside a chroot, and all the files are owned by www-data so it shouldn't be a permission error. I made a new php file in the same directory to produce an error and it logs just fine so it has to be just phpmyadmin. Here's my php5-fpm pool: [phpmyadmin] listen = /var/vhosts/phpmyadmin/tmp/.php.sock; user = www-data group = www-data chroot = /var/vhosts/phpmyadmin/ chdir = / php_admin_value[error_reporting] = E_ALL php_admin_value[error_log] = error.log php_admin_flag[log_errors] = on php_admin_flag[display_errors] = on php_value[session.save_handler] = files php_value[session.save_path] = /tmp And Nginx server block: server { listen 80; root /var/vhosts/phpmyadmin/www; server_name pma.domain; location / { try_files $uri $uri/ /index.html; autoindex on; } location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(/.+)$; include fastcgi_params; fastcgi_pass unix:/var/vhosts/phpmyadmin/tmp/.php.sock; fastcgi_param SCRIPT_FILENAME /www$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_param DOCUMENT_ROOT /www; } index index.html index.htm index.php; try_files $uri $uri/ =404; } Any ideas what could be wrong? Why is it not producing any errors even though I've forced them to be on?

  Read the article

• Trouble with Russian pc's on my wifi

  - by hogni89

  I have created a WiFi hotspot for the local community. The problem is, some Russian PC's (Windows XP, Windows Vista and Windows 7) can't get internet connection (We have a lot of bypassing russian fishing vessels / cargo ships). The pc's obtain a valid IP address, and some of them can even manage to send some few packages - But none of them are usable on the network. They all say "Limited internet access" or "???????????? ?????? ? ????????". The thing these PC's have in common is, that they all run a Russian installation of Windows. No one else has problems with the WiFi hotspot - Danish and English Windows, Linux and OS X all work like a charm. Can it be, that there is a difference between the danish / english windows installation, compared to the Russian installation? EDIT START They can't ping the router (One PC got one response - ONCE), they can't access any sites and Windows newer asks "Is this network public, home or work?". EDIT END PS: The hotspot is a airMAX rocket M from Ubiquiti Networks, Inc (www.ubnt.com)

  Read the article

• Can't remote into Virtual PC

  - by Spamela

  I used to be able to remote into my Virtual PCs. It has been working for at least a year. Yesterday just stopped working... I cannot figure it out... Things I have triple-checked: 1. My Virtual PCs have "Allow Remote Access" checked. 2. My Virtual PCs have an account in the Administrator group that is password protected. 3. My Host's entry in the registry for the Terminal Services Port is still the default of 3389. So here is the strange thing. I can't even remote into the Virtual PC from it's host much less another PC... From the host, I can ping the Virtual PC and get a response but when trying to remote into it from the host I get the following error: Remote Desktop can't connect to the remote computer for one of these reasons: 1)Remote access to the server is not enabled. 2)The remote computer is turned off 3)The remote computer is not available on the network My host is running Windows 7. Virtual PCs are running XP. Thank you for looking at this!

  Read the article

• W2003StdR2 server: DNS dysfunctional!

  - by Tor

  I hate to have to do this, but i feel up that creek with no... well, some of you might know. At the moment my one and only DNS server refuses to do Forwarding. The story is as goes: This site had 2 servers, one W2003SBS and an W2003StdR2. The SBS degraded over a short periode of time, and to not go down with it i decided to move all data over to the other server. This was of course an AD integrated site. Move went ok, the Std server removed from the domain, and the SBS put to rest. For the time being we decided to run the Std as a server only, and no AD. We renamed the internal domain to xxx.local, and set the server up with DNS, DHCP and installed WINS (not activated). Forwarding of DNS is to our ISP through a Netgear Firewall. The same address setup used as before. So - DNS server started and all went ok, clients reconfigured and hooked up and then - after a day's time - internet name resolution stopped working on the server! Nothing had changed, been altered, modified, nothing! What i now get when doing NSLOOKUP is just a 2 sec timeout response! And i have checked and looked, but to no avail. Anybody seen this behaviour before? And yes - ALL servicepacks have been updated on the server. I would be much obliged if anyone in here could lend an ear... and give advice! Thanks.... from Tor in Norway Today is the 14th, and i still have no resolution to this nagging problem. Anybody else got any advice in the matter? Please?

  Read the article

• Exchange emails not delivering for one user

  - by Cylindric

  We have an Exchange infrastructure going through a migration from 2003 SP2 (call it ExOld) to 2010 (ExNew). All users are now on the new server, but mail is still being directed to ExOld until testing is complete. ExNew sends emails directly to the internet. For one particular user, emails don't seem to be being reliably delivered, but the odd thing is that it's not all emails. I can see external emails in his inbox. If I send an internal email it works fine. If I send an email from Gmail to him it doesn't get through. If I telnet from outside to ExOld I can send an email to him. If I telnet from outside to ExNew I can send an email to him. This is a transcript that results in a successful send: 220 ExOldName Microsoft ESMTP MAIL Service, Version: 6.0.3790.4675 ready at Mon, 22 Oct 2012 10:55:26 +0100 EHLO test.com 500 5.3.3 Unrecognized command EHLO test.com 250-ExOldFQDN Hello [MyTestExternalIp] 250-TURN 250-SIZE 250-ETRN 250-PIPELINING 250-DSN 250-ENHANCEDSTATUSCODES 250-8bitmime 250-BINARYMIME 250-CHUNKING 250-VRFY 250-X-EXPS GSSAPI NTLM LOGIN 250-X-EXPS=LOGIN 250-AUTH GSSAPI NTLM LOGIN 250-AUTH=LOGIN 250-X-LINK2STATE 250-XEXCH50 250 OK MAIL FROM:[email protected] 250 2.1.0 [email protected] OK RCPT TO:[email protected] notify=success,failure 250 2.1.5 [email protected] DATA 354 Start mail input; end with . Subject:Test 1056 Test 10:56 . 250 2.6.0 Queued mail for delivery quit 221 2.0.0 ExOldFQDN Service closing transmission channel Emails go through Symantec Cloud, but their "Track and Trace" shows the messages going through, with a "delivered ok" log entry. 2012-10-22 09:19:56 Connection from: 209.85.212.171 (mail-wi0-f171.google.com) 2012-10-22 09:19:56 Sending server HELO string:mail-wi0-f171.google.com 2012-10-22 09:19:56 Message id:CAE5-_4hzGpY2kXFbzxu7gzEUSj5BAvi+BB5q1Gjb6UUOXOWT3g@mail.gmail.com 2012-10-22 09:19:56 Message reference: 135089759500000177171130001194006 2012-10-22 09:19:56 Sender: [email protected] 2012-10-22 09:19:56 Recipient: [email protected] 2012-10-22 09:20:26 SMTP Status: OK 2012-10-22 09:19:56 Delivery attempt #1 (final) 2012-10-22 09:19:56 Recipient server: ExOldIP (ExOldIP) 2012-10-22 09:19:56 Response: 250 2.6.0 Queued mail for delivery I'm not sure where to look on the old (or new) server for information as to where the mails are ending up.

  Read the article

• Is there a utility to visualise / isolate and watch application calls

  - by MyStream

  Note: I'm not sure what to search for so guidance on that may be just as valuable as an answer. I'm looking for a way to visually compare activity of two applications (in this case a webserver with php communicating with the system or mysql or network devices, etc) such that I can compare the performance at a glance. I know there are tools to generate data dumps from benchmarks for apache and some available for php for tracing that you can dump and analyse but what I'm looking for is something that can report performance metrics visually from data on calls (what called what, how long did it take, how much memory did it consume, how can that be represented visually in a call stack) and present it graphically as if it were a topology or layered visual with different elements of system calls occupying different layers. A typical visual may consist of (e.g. using swim diagrams as just one analogy): Network (details here relevant to network diagnostics) | ^ back out v | Linux (details here related to firewall/routing diagnostics) ^ back to network | | V ^ back to system Apache (details here related to web request) | | ^ response to V | apache PHP (etc) PHP---------->other accesses to php files/resources----- | ^ v | MySQL (total time) MySQL | ^ V | Each call listed + time + tables hit/record returned My aim would be to be able to 'inspect' a request/range of requests over a period of time to see what constituted the activity at that point in time and trace it from beginning to end as a diagnostic tool. Is there any such work in this direction? I realise it would be intensive on the server, but the intention is to benchmark and analyse processes against each other for both educational and professional reasons and a visual aid is a great eye-opener compared to raw statistics or dozens of discrete activity vs time graphs. It's hard to show the full cycle. Any pointers welcome. Thanks! FROM COMMENTS: > XHProf in conjunction with other programs such as Perconna toolkit > (percona.com/doc/percona-toolkit/2.0/pt-pmp.html) for mySQL run apache > with httpd -X & (Single threaded debug mode and background) then > attach with strace -> kcache grind

  Read the article

• 100% uptime for a web application

  - by Chris Lively

  We received an interesting "requirement" from a client today. They want 100% uptime with off-site failover on a web application. From our web application's viewpoint, this isn't an issue. It was designed to be able to scale out across multiple database servers, etc. However, from a networking issue I just can't seem to figure out how to make it work. In a nutshell, the application will live on servers within the client's network. It is accessed by both internal and external people. They want us to maintain an off-site copy of the system that in the event of a serious failure at their premises would immediately pick up and take over. Now we know there is absolutely no way to resolve it for internal people (carrier pigeon?), but they want the external users to not even notice. Quite frankly, I haven't the foggiest idea of how this might be possible. It seems that if they lose Internet connectivity then we would have to do a DNS change to forward traffic to the external machines... Which, of course, takes time. Ideas? UPDATE I had a discussion with the client today and they clarified on the issue. They stuck by the 100% number, saying the application should stay active even in the event of a flood. However, that requirement only kicks in if we host it for them. They said they would handle the uptime requirement if the application lives entirely on their servers. You can guess my response.

  Read the article

• Running .NET code in XML file [closed]

  - by Stuart McIntosh

  We have 2 servers, 1 already configured with .net which works fine and a new one which appears to be configured the same but when I open an xml page in Internet Explorer it complains about the <% tag. We have IIS on win srvr 2003 SP2. The website is configured with .NET 1.1.4322. In ISAPI extensions have set the .XML extension to use c:\windows\microsoft.net\framework\v1.1.4322\aspnet_isapi.dll But the page: <property name="documentmaxage" value="0"/> <property name="documentmaxstale" value="0"/> <var name="m_Prompt_Path" /> <form id="InitVoiceXmlDoc"> <block> <assign name="m_Prompt_Path" expr="&quot;<% Response.Write(Request.QueryString["m_Prompt_Path"]); %>&quot;"/> </block> </form> gives the error: The XML page cannot be displayed Cannot view XML input using XSL style sheet. Please correct the error and then click the Refresh button, or try again later. The character '<' cannot be used in an attribute value. Error processing resource 'http://localhost:11119/fails.xml'. Lin... &quo... We have the same config on another server which works fine. So are there other options apart from the ISAPI extensions that I need to look at

  Read the article

• Force encoding with IIS 7

  - by Cédric Boivin

  I try to force encoding with IIS 7. When I add in the http response headers the key : Content-Type and value charset=utf-8 i got this key content-type : text/html,content-type=utf-8 it's there a way to remove the comma ? Thanks Justin for your answer. But it's seen don't work. There is my config, i need to do that for asp classic. <?xml version="1.0" encoding="UTF-8"?> <configuration> <system.webServer> <staticContent> <remove fileExtension=".html" /> <remove fileExtension=".hxt" /> <remove fileExtension=".htm" /> <remove fileExtension=".asp" /> <mimeMap fileExtension=".htm" mimeType="text/html" /> <mimeMap fileExtension=".hxt" mimeType="text/html" /> <mimeMap fileExtension=".html" mimeType="text/html" /> <mimeMap fileExtension=".asp" mimeType="text/html; charset=UTF-8" /> </staticContent> </system.webServer> </configuration>

  Read the article

• Basic IPTables setup for OpenVPN/HTTP/HTTPS server

  - by Afronautica

  I'm trying to get a basic IPTables setup on my server which will allow HTTP/SSH access, as well as enable the use of the server as an OpenVPN tunnel. The following is my current rule setup - the problem is OpenVPN queries (port 1194) seemed to be getting dropped as a result of this ruleset. Pinging a website while logged into the VPN results in teh response: Request timeout for icmp_seq 1 92 bytes from 10.8.0.1: Destination Port Unreachable When I clear the IPTable rules pinging from the VPN works fine. Any ideas? iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A FORWARD -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -A INPUT -p tcp -m state --state NEW --dport 22 -j ACCEPT iptables -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT iptables -A INPUT -j REJECT iptables -A FORWARD -j REJECT

  Read the article

• TortoiseSVN client slows Explorer to a crawl in Windows XP running in Parallels

  - by Cory Larson

  I thought I'd make my first SuperUser question relatively simple, though it's the kind of question that may not get many responses as I'm not directly involved with the issue. A colleague does his development in Windows XP running in Parallels on his Mac. We've just migrated our VSS repository to SVN, and we've gone with TortoiseSVN as our client of choice with the Ankhsvn plugin for Visual Studio. On his XP instance, after installing TortoiseSVN, browsing through folders using Explorer is extremely slow; about 15 - 30 seconds before the contents of the next folder displays. It's the slowest when opening My Computer. Once he reaches a folder that contains the working content of an SVN project, Explorer behaves quickly again as expected. It seems that TortoiseSVN may be spending a bunch of time searching subfolders for stuff so it can do its icon-overlay thing, but that's just a guess. I've used TortoiseSVN for years on both XP and Vista on far less powerful machines without any issues with Explorer, so I'm attributing the slowness to it being run in a VM, though that may not be the actual issue. So has anyone encountered similar performance issues, and/or know of a fix? Keep in mind that any requests to make changes to his configuration will need to be communicated and thus my response time might be slow. Thanks everyone!

  Read the article

< Previous Page | 276 277 278 279 280 281 282 283 284 285 286 287  | Next Page >