Search Results

Search found 21511 results on 861 pages for 'appstore approval process'.

Page 281/861 | < Previous Page | 277 278 279 280 281 282 283 284 285 286 287 288  | Next Page >

  • MacBook Pro battery capacity 65K mAh

    - by Alexander Gladysh
    I have a 15" MacBook Pro 3.1 (that is Late 2007 model AFAIR). I've bought it new a couple of years ago. Recently its on-battery power lifespan became very short (30 to 10 minutes). When my notebook turns itself off due to "low battery" and I press the small button on the battery itself, all LED lights are alight, indicating full charge. When I plug in the power adapter, my Mac displays that "battery is fully charged, finishing charging process" (I have a Russian OS X 10.5.7, so that is a rough translation), but the LEDs on battery itself display (seemingly accurate) status that there are one or two "LEDs still not charged". My battery have as few as 37 recharge cycles (yes, I've neglected calibration over the time I've used it). Battery info programs like iBatt2 report battery capacity of 65 337 mAh (with by-design capacity of 5600 mAh). I get it that something went wrong with battery electronics. I've tried resetting my Mac's PRAM and SMC, it did not changed anything. Now I'm trying to recalibrate the battery, but looks like it does not help as well. Will try to recalibrate it several times in a row. I'd buy a new battery if I knew if it is battery fault, not a notebook's. Any suggestions? Update: After recalibration, my battery status now displays battery capacity of 1500 mAh. But with every recalibration (or simply when I use notebook without power adapter plugged in) this number changes in the range from 200 mAh to 1700 mAh. LEDs on battery now are synchronous with what nodebook thinks on the charge level. Also I've noticed that cycle count changes rather slowly. It is now 39, it was 37 when I've started recalibration, and I went through the process at least ten times... So, the main question is: does it look like that replacing the battery would help me (or does it look like this is notebook's problem)? I guess I should try replacing the battery.

    Read the article

  • VMWare Converter - Remote Linux Install P2V

    - by Zed Said
    I am trying to get what I thought was an easy process working. Here is my situation. I have a remote linux server (running Debian) that I would like to turn into a VM so that I can do testing on it rather than the production server. I downloaded VMWare Converter. I went to the "convert machine" wizard, chose Powered-on machine, entered my remote machine details. Clicking next shows that it correctly connects to my remote linux box. Now, on the next screen, for Destination type, it enters "WMWare Infrastructure virtual machine", and I can't change this. This is where I am stuck. Why do I need another sever to convert with? Is this where my VM gets sent to? And why can't I just convert the VM and save it on the computer that I am running the converter program on? If I do have to use a vmware infrastructure destination, I am confused at what ESX is, why and how I use it. Any help with this process would be more than appreciated!

    Read the article

  • 'pskill \\hostname winlogon' might budge a server "stuck rebooting", but why?

    - by Snoi
    Question: Executing remote (Sysinternals) command... pskill \\machine winlogon ...can budge a server that is stuck rebooting, but how/why does this work? How do you know which service to kill? To recreate (e.g.): You run Windows Update, allow a reboot, and ...NOTHING! RDP gets cut off but the server does not reboot. Just about every other service seems to stay up. Further Background: I've faced this problem on VMs hosted around the planet for some years, and used various sc.exe and shutdown commands to learn the state of and attempt remote reboot of servers in such a state, with limited success. Most datacentres don't offer any way to see the true console or power off/on such machines. They charge $$ for you to call them to do such simple things after hours, when you nearly always have to run your maint tasks. e.g. NET USE \\machine\IPC$ /USER:login password sc \\machine query RpcSs sc \\machine query TermService sc \\machine query wuauserv tasklist /s machine This occasionally works for me... shutdown /m \\machine /r /f /t: 0 ...but more often than not it fails with: A system shutdown is in progress (1115). I found this question, and the answer by @Tweek, and it worked really well, but was I just lucky? Can not RDP to Win 2003 box or initiate remote restart @Tweek said to run: pskill \\hostname winlogon ...and that got me past this situation in a new way (Server 2008 R2 in my most recent case) - really useful! I just need to understand if I got lucky or there is more science here. What I'd like to know is why the winlogon process? @Livne said to use "tasklist /s HostName" to see what is the culprit, but how do you tell from the listed output? It's just a list of running tasks etc. From that I would not know what to look for, nor could I see anything about the winlogon process that suggested to my eyes that was the one to kill.

    Read the article

  • Login box not shown on Ubuntu

    - by Alexandre
    I've installed Ubuntu 10.04 (64bit) as a guest OS in VirtualBox, using Windows7 Professional (64bit) as host. After Ubuntu install, I did installed Xfce4 (sudo apt-get install xfce4). Logged in using a Xfce session, and when I logged out, I couldn't see the login box anymore, only the regular gnome background from login screen. Then I restarted the virtual machine, and now I'm not able to see the login box anymore, only the gnome background. Does someone knows how to solve this? Thanks in advance Update: I've tried to use Xubuntu, that comes with Xfce. And I'm facing the same problem. As a common denominator from the two cases, now I see the problem arises after I've updated the system, and then installed curl (via apt-get), zlib (make process), git (make process). But I'm not sure this can be the cause for this ... Update: I isolated the problem. The bad guy is zlib, but I don't have a clue why. In fact, it does crash not only ubuntu and xubuntu, but also Debian (Yes, I've tested all). I'll keep this question in case someone have the same problem, but I think my initial question is not valid anymore.

    Read the article

  • SQL Server 2008 Unique Problem for bring DB Online...

    - by Nai
    This is my error I am facing TITLE: Microsoft.SqlServer.Smo Set offline failed for Database 'Go3D_Retailer ------------------------------ ADDITIONAL INFORMATION: An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) Unable to open the physical file "E:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA\ftrow_Go3D_catalog.ndf". Operating system error 2: "2(failed to retrieve text for this error. Reason: 15105)". Database 'Go3D_Retailer' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. ALTER DATABASE statement failed. (Microsoft SQL Server, Error: 5120) Background to this error I've been trying to move my destination logshipping database to another physical server for analysis purposes. Because I do not have active directory set up, I had to hack my process by using the same username/password for both the source and destination servers to get the process to work. Following that, I used this guy's solution to move the destination database to another server. However, this error occurs when I try to bring the database back online. I don't have an E drive on my server and I have no idea why it's trying to open a file from E drive. I have over a 100gb left on my hard disk so it's definitely not a space issue. This sounds like a bug... Any ideas? I'm running SQL Server 2008 Enterprise edition on Windows Server 2008 R2 64bit

    Read the article

  • Postgresql server will not start

    - by Claudiu
    I'm on Windows 7. I restarted my computer. I then tried to connect to the database and got an error. I don't remember which one in particular but it was some connection issue. I decided to try to restart the server, so I clicked on "Restart server" from the start menu. This blocked. After a few minutes I killed the process and tried again, only to get a "The service is starting or stopping. Please try again later." message. I rebooted the computer again, tried to start again, and got the same error. I killed the pg_ctl process and tried starting it manually, but that didn't work either: C:\Users\DrClaud>cscript "C:\Program Files\PostgreSQL\8.3\scripts\serverctl.vbs" start wait Microsoft (R) Windows Script Host Version 5.8 Copyright (C) Microsoft Corporation. All rights reserved. The PostgreSQL Server 8.3 service is starting................................... ....................................... The PostgreSQL Server 8.3 service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534. The start command returned an error (2) Any ideas?

    Read the article

  • COM+/Desktop Heap errors in IIS affecting sites at random?

    - by tresstylez
    We have a Win2K3 server that is hosting 30+ sites. Each site is configured to have its own unique application pool -- so that we can manually recycle specific sites if needed and not kill sessions for the others. From what I've read, the consequence of this type of setup is that each application pool worker process gets allocated a Desktop Heap (normally 512 kb's) and we limit the number of app pools we can serve. http://blogs.msdn.com/b/david.wang/archive/2006/01/25/security-considerations-of-usesharedwpdesktop-on-iis6.aspx PROBLEM: What we're seeing is that occasionally COM+ errors get triggered, presumably by hitting our 512 kb limit of the desktop heap -- and certain sites become unresponsive (or have errors) until we manually recycle that specific app pool. I know that I can increase the desktop heap limit to 1024, and make other tweaks/tunes, but I've been tasked with finding out what exactly causes one site's heap to max out as opposed to another. It seems that when we start seeing COM+ errors, the sites it affects are random -- small sites or big sites (heavier used). Is it based on process id? Traffic? Any pointers on understanding this a little more would be excellent. Thanks! jg

    Read the article

  • Unable to stop chrome.exe *32

    - by chipperyman573
    So I was installing roboform today and was unable to stop the process chrome.exe *32... Even when I uninstalled chrome. This is the error I got: I used lockhunter and it said it was located in %appdata%\Local\Google\Chrome. However, it was unable to unlock, delete or rename. When I use explorer to delete or rename that folder, it says it's being used by Chrome. Even after restarting my computer it still does this. I've tried using the built in chrome task manager (Wrench View Background Pages) and I can't seem to find a process there that has the same amount of memory. I have run many, many virus scans, by: Microsoft security essentials AVG (Free version) Malwarebytes (Pro version) Norton 360 (Pro version) McAfee (Pro Version) Avira (Free version) Avast! Antivirus (Free version) None of which returned with any viruses. Chrome info: Google Chrome 23.0.1271.95 (Official Build 169798) OS Windows 7 Professional WebKit 537.11 (@135931) JavaScript V8 3.13.7.5 Flash 11.5.31.2 User Agent Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.11 (KHTML, like Gecko) Chrome/23.0.1271.95 Safari/537.11

    Read the article

  • Is it possible to be a Linux professional studying on your own?

    - by Marc Jr
    I read economics at university(nothing to see with linux, isn't it? :P). I have some basic knowledge about booting process, Linux Kernel compiling from source and stuff like that. But of course I have still much to learn sometimes some errors appears and "voila" I am lost. I had: Ubuntu, Fedora, OpenSuse, Arch.. using Gentoo now. I'd like to know what you linux users, professionals, administrators... would think it is the best way to learn linux in a professional way. Is it worth studying it and passing the LPIC test enough to work in the linux world? or do I need going to IT uni? I've heard LFS is a good way of learning about linux, is that real? I've been thinking about getting to LFS learn about more deeply about the linux process and learning scripts. It is possible to do this way? if anyone has a tip or a good way of doing, maybe someone did it. Any tip is very welcome. Words from a person in love with linux. :D The best, Marc

    Read the article

  • Can’t connect to SQL Server 2008 - looks like Shared Memory problem

    - by user38556
    I am unable to connect to my local instance of SQL Server 2008 Express using SQL Server Management Studio. I believe the problem is related to a change I made to the connection protocols. Before the error occurred, I had Shared Memory enabled and Named Pipes and TCP/IP disabled. I then enabled both Named Pipes and TCP/IP, and this is when I started experiencing the problem. When I try to connect to the server with SSMS (with either my SQL server sysadmin login or with windows authentication), I get the following error message: A connection was successfully established with the server, but then an error occurred during the login process. (provider: Named Pipes Provider, error: 0 - No process is on the other end of the pipe.) (Microsoft SQL Server, Error: 233) Why is it returning a Named Pipes error? Why would it not just use Shared Memory, as this has a higher priority order in the list of connection protocols? It seems like it is not listening on Shared Memory for some reason? When I set Named Pipes to enabled and try to connect, I get the same error message. My windows account is does not have administrator priviliges on my computer - perhaps this is making a difference in some way (as some of the discussions in this post about an "SuperSocketNetLib\Lpc" registry key seems to suggest). I have tried restarting the SQL Server service, by the way, and also tried to get someone to log onto the machine with an admin account to restart the SQL Server service. Still no luck.

    Read the article

  • How to upgrade Apache 2 from 2.2 to 2.4

    - by Nina
    I was in the process of doing a test upgrade from Apache 2.2 to 2.4.3. I'm using Ubuntu 10.04. I would have upgraded to 12.04 for this to see if the upgrade would go a lot smoother. Unfortunately, I was told it wasn't an option...so I'm stuck using 10.04. The process I did this was: Before attempting this, I have managed to upgrade APR from 1.3 to 1.4 as well since apache told me it was a requirement beforehand: http://apr.apache.org/download.cgi First remove all traces of the current apache: sudo apt-get --purge remove apache2 sudo apt-get remove apache2-common apache2-utils apache2.2-bin apache2-common sudo apt-get autoremove whereis apache2 sudo rm -Rf /etc/apache2 /usr/lib/apache2 /usr/include/apache2 Afterwards, I did the following: sudo apt-get install build-essential sudo apt-get build-dep apache2 Then install apache 2.4 with the following: wget http://apache.mirrors.tds.net//httpd/httpd-2.4.3.tar.gz tar -xzvf httpd-2.4.3.tar.gz && cd httpd-2.4.3 sudo ./configure --prefix=/usr/local/apache2 --with-apr=/usr/local/apr --enable-mods-shared=all --enable-deflate --enable-proxy --enable-proxy-balancer --enable-proxy-http --with-mpm=prefork sudo make sudo make install After the make install, I ended up getting a series of errors that prevented it from installing correctly: exports.c:2513: error: redefinition of 'ap_hack_apr_uid_current' exports.c:1838: note: previous definition of 'ap_hack_apr_uid_current' was here exports.c:2514: error: redefinition of 'ap_hack_apr_uid_name_get' exports.c:1839: note: previous definition of 'ap_hack_apr_uid_name_get' was here exports.c:2515: error: redefinition of 'ap_hack_apr_uid_get' exports.c:1840: note: previous definition of 'ap_hack_apr_uid_get' was here exports.c:2516: error: redefinition of 'ap_hack_apr_uid_homepath_get' Looking for exports.c only leads me back to the httpd-2.4.3 folder. So I'm not sure what these errors mean... Thanks in advance for any help you have to offer!

    Read the article

  • Windows Server 2008 R2 SP1 Drivers Missing Would Not Install?

    - by bleepzter
    I am building my dev machine with WS2008R2SP1. I consider Windows Server as the best development environment for C# since I tend to focus on server-centric (integration) applications. The desktop flavor of Windows (7) doesn't play nicely with things like Commerce Server or BizTalk... so I to like stick to the environment I develop for. Previously I used to develop inside of VM's but I've found that it is super inefficient and tends to take a toll on the laptops. (I've gone through two of them in 6 months). Problem is that I multiple devices that do not want to be recognized by Windows: My machine is Dell Precision M4500: Intel Core i7-Q740, 1TB HDD, 8GB RAM, Dell re-branded Broadcom DW1501 802x11n Half-Mini Card, Dell re-branded Broadcom DW375 Bluetooh Module, Intel 82577LM Gigabit Network connection NVidia Quadro FX1800 Graphics The devices in question are the Dell rebranded broadcom network and bluetooth adapters: Broadcom USH: USB\VID_0A5C&PID_5800&REV_0101&MI_00 USB\VID_0A5C&PID_5800&MI_00 DW375 Bluetooth Module USB\VID_413C&PID_8187&REV_0517 USB\VID_413C&PID_8187 When I ran the broadcom installers I get "Operating System not supported" which I think is a big oversight on Broadcom's part. Why check for system version string? UGHGHGH Moreover if I try to manually force the driver in windows... I get an error: Driver Management concluded the process to install driver FileRepository\btwampsecfl.inf_amd64_neutral_d8fc2b85d035ed47\btwampsecfl.inf for Device Instance ID USB\VID_0A5C&PID_5800&MI_00\7&66DE6C9&0&0000 with the following status: 0xe0000217. '- or - Driver Management concluded the process to install driver FileRepository\btwampfl.inf_amd64_neutral_d4c4acf036c61299\btwampfl.inf for Device Instance ID USB\VID_413C&PID_8187\90004EEEF5A6 with the following status: 0xe0000217. I googled the 0xe0000217 error code and it says Bad service install section in the driver inf file... Any ideas on how to fix this? I also tried the post by BetaIQ on MSDN Forum, unfortunately the links to the driver package included in the post were dead :( PS. On a side note I also do mobile development for Android, iOS, and Windows Phone, and BB. Having the bluetooth is quite useful with mobile devices.

    Read the article

  • Windows Server (SBS) 2008 - Telephony service won't start (missing permissions)

    - by Uri
    I am running a SBS 2008 server. It's setup as the domain controller for the network. After a reboot, the Telephony service (and all services that depend on it) refuses to start under the Network Service account. The error given is: Error 1297: A privilege that the service requires to function properly does not exist in the service account configuration. You may use the Services Microsoft Management Console (MMC) snap-in (services.msc) and the Local Security Settings MMC snap-in (secpol.msc) to view the service configuration and the account configuration. This has caused all the network services not to be accessible e.g. terminal services, VPN (RRAS), SQL Server instances. The SSH daemon I have running on the box will accept connections only from localhost, but won't respond on the network. After searching around, the only advice I could find was to grant the Network Service account these permissions: Adjust memory quotas for a process Replace a process level token I set those permissions on both the Default Domain Policy and the Default Domain Controller Policy, but it seemingly had no effect. Most of the services will start if I change them to run under the Local System account, but that didn't make them accessible on the network. I even tried removing the Routing and Remote Access Services feature, rebooting and reinstalling it, but the issue remains. Any ideas?

    Read the article

  • Apache2 will not start on OpenSUSE after enabling mod_pagespeed

    - by alpha1
    I have a linode VPS, running openSUSE 12.1 (A little outdated, but stable). I have installed the RPMS for mod_pagespeed. mod_pagespeed.conf has "ModPagespeed on". Restarting apache fails after enabling pagespeed. the errors are not very helpful. li361-39:/usr/lib64/apache2 # a2enmod pagespeed li361-39:/usr/lib64/apache2 # service apache2 restart redirecting to systemctl Job failed. See system logs and 'systemctl status' for details. li361-39:/usr/lib64/apache2 # systemctl status apache2.service apache2.service - apache Loaded: loaded (/lib/systemd/system/apache2.service; enabled) Active: failed since Thu, 06 Jun 2013 20:49:00 +0000; 1s ago Process: 6701 ExecStop=/usr/sbin/httpd2 -D SYSTEMD -k stop (code=exited, status=0/SUCCESS) Process: 6704 ExecStart=/usr/sbin/start_apache2 -D SYSTEMD -k start (code=exited, status=1/FAILURE) Main PID: 6637 (code=exited, status=0/SUCCESS) CGroup: name=systemd:/system/apache2.service li361-39:/usr/lib64/apache2 # a2dismod pagespeed li361-39:/usr/lib64/apache2 # service apache2 restart redirecting to systemctl li361-39:/usr/lib64/apache2 # And the error log (/var/log/apache2/error_log) is useless as well. [Thu Jun 06 20:48:59 2013] [notice] caught SIGTERM, shutting down [Thu Jun 06 20:49:12 2013] [warn] Init: Session Cache is not configured [hint: SSLSessionCache] [Thu Jun 06 20:49:13 2013] [notice] Apache/2.2.21 (Linux/SUSE) mod_ssl/2.2.21 OpenSSL/1.0.0k PHP/5.4.15 configured -- resuming normal operations EDIT This is from /var/log/messages Jun 12 14:24:14 li361-39 start_apache2[27951]: httpd2-prefork: Syntax error on line 116 of /etc/apache2/httpd.conf: Syntax error on line 34 of /etc/apache2/sysconfig.d/loadmodule.conf: Cannot load /usr/lib64/apache2/mod_pagespeed.so into server: /usr/lib64/apache2/mod_pagespeed.so: undefined symbol: ap_unixd_config Full Log is here: http://pastebin.com/hjnbZZTr I've tried looking for other logs and checking the mod_pagespeed.conf against posts claiming it works and nothing is striking as wrong. Any Ideas?

    Read the article

  • Cisco "copy startup-config tftp" results in a 0 byte file on the server?

    - by Geoffrey
    I'm pulling my hair out figuring this out. My startup-config is good, I can view it with a show command. I'm trying to copy it to a tftp server: asa5505# copy startup-config tftp Address or name of remote host []? ipaddress Destination filename [startup-config]? t !! %Error writing tftp://ipaddress/t (Timed out attempting to connect) On my TFTP server (SolarWinds), I get the following: binary, PUT. Started file name: C:\TFTP-Root\t binary, PUT. File Exists, C:\TFTP-Root\t binary, PUT. Deleting Existing File. binary, PUT. Interrupted by client, cause: The process cannot access the file 'C:\TFTP-Root\t' because it is being used by another process I've used tftpd32 with same results. I've tried different servers, even one on the same network as the asa ... same results. It'll create a 0 byte file and never do the dump. What's going on? Everything is working normally except for this.

    Read the article

  • Cannot start listening on a certain TCP port, but there's nothing currently listening on it

    - by John Rasch
    I have Windows Service that uses a WCF service host to listen for connections on TCP port 61000. When I try to start the service, I get the error: Service cannot be started. System.ServiceModel.AddressAlreadyInUseException: HTTP could not register URL http://+:61000/ because TCP port 61000 is being used by another application. ---> System.Net.HttpListenerException: The process cannot access the file because it is being used by another process at System.Net.HttpListener.AddAll() at System.Net.HttpListener.Start() at System.ServiceModel.Channels.SharedHttpTransportManager.OnOpen() --- End of inner exception stack trace --- at System.ServiceModel.Channels.SharedHttpTransportManager.OnOpen() at System.ServiceModel.Channels.TransportManager.Open(TransportChannelListener channelListener) at System.ServiceModel.Channels.TransportManagerContainer.Open(SelectTransportManagersCallback selectTransportManagerCallback) at System.ServiceModel.Channels.HttpChannelListener.OnOpen(TimeSpan timeout) at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout) at System.ServiceModel.Dispatcher.ChannelDispatcher.OnOpen(TimeSpan timeout) at... A quick netstat -a shows there is nothing listening on port 61000. I've also found several posts online that mention reserving namespaces using netstat, but the account that the service runs under has administrator privileges so that shouldn't be necessary. Any other ideas as to why I'm getting this message? This service is running on 64-bit Windows Server 2008 R2 Standard.

    Read the article

  • Outlook slow to open attachments

    - by Alistair McMillan
    When a colleague tries to open attachments in her email (Outlook 2003 talking to an Exchange 2007 server) they talk ages to open. The files are relatively small, all less than 1MB. We've tried creating a new Windows profile for the user and tried creating new Outlook profiles, however that hasn't made any difference. And we've tried accessing her account from someone else's PC, and the attachments open immediately there. The only thing that might provide a clue is that Process Monitor shows Outlook on her PC trying to write the file to a folder within the user's "Temporary Internet Files" folder with FAST I/O DISALLOWED errors. Can't find a lot of useful information on that message online though. What causes the FAST I/O DISALLOWED errors? And would that make opening attachments so incredibly slow that opening a < 1MB file can take a matter of minutes? UPDATE: Discovered that this isn't just an issue with Outlook. Other files being accessed over the network show the same FAST I/O DISALLOWED errors in Process Monitor. The problem is just more noticeable with Outlook, because although other applications take a while to open files it isn't a matter of minutes.

    Read the article

  • Apache + mod_fcgid + perl = error 500

    - by f-aminov
    Hi guys! I'm trying to setup Apache2.2 with mod_fcgid and libapache2-mod-perl2 with no luck. I've created a fcgi-bin directory in the root directory of my website and put there a test.fcgi file with the following content: #!/usr/bin/perl use CGI; print "This is test.fcgi!\n"; While trying to access it via http://www.website.dom/fcgi-bin/test.fcgi I get error 500 (Internal Server Error). Here is my vhost config: <VirtualHost 95.131.29.226:8080> ServerName website.com DocumentRoot /var/www/data/website.com SuexecUserGroup user group ServerAlias www.website.com AddType application/x-httpd-php .php .php3 .php4 .php5 .phtml <Directory "/var/www/data/website.com/fcgi-bin/"> Options +ExecCGI Allow from all Order allow,deny AddHandler fcgid-script .fcgi </Directory> </VirtualHost> fcgid.conf: <IfModule mod_fcgid.c> AddHandler fcgid-script .fcgi SocketPath /var/lib/apache2/fcgid/sock IdleTimeout 3600 ProcessLifeTime 7200 MaxProcessCount 8 DefaultMaxClassProcessCount 2 IPCConnectTimeout 8 IPCCommTimeout 60 </IfModule> SuExec log: [2010-04-06 03:02:47]: uid: (500/equ) gid: (502/equ) cmd: test.fcgi Apache error log: test! test! [Tue Apr 06 03:02:51 2010] [notice] mod_fcgid: process /var/www/data/website.com/fcgi-bin/test.fcgi(26267) exit(communication error), terminated by calling exit(), return code: 0 [Tue Apr 06 03:02:53 2010] [notice] mod_fcgid: process /var/www/data/website.com/fcgi-bin/test.fcgi(26261) exit(server exited), terminated by calling exit(), return code: 0 I've no clue why I'm getting error 500, but when I'm trying to access this file using console ($ perl /var/www/data/website.com/fcgin-bin/test.fcgi) everthing works fine without any errors... Any suggestions on how to solve this problem would be greatly appreciated. Thank you!

    Read the article

  • Outlook 2010, 2007 Sync problems after migration from SMTP to Exchange

    - by kirgy
    Our organization recently switched from an SMTP server to an Exchange server, since then several user's Outlook's are not synchronizing their emails as expected with the Exchange server. Our move over from an SMTP server to an Exchange server consisted of adding the new Exchange account alongside the existing SMTP account, drag-dropping/copy-pasting folders client-side from the SMTP account in the folder pane in outlook, to the newly created Exchange account. The problem happens when a user moves an email to a folder from their inbox or another folder. At this point the email disappears from Outlook client side. Re-syncing the folder, send/receive, closing/opening outlook and even system reboots do not make this email reappear. The Outlook web interface (OWA) reports the email is in fact in the folder they placed it in, and is not deleted. Doing a "search all mail items" for the emails shows that the email is still there; not deleted nor removed. To add to the confusion, when new folders are created and the email is placed in these folders, the synchronization happens without any issue both client side and server side. As the emails are appearing server side, we are confident to presume this is a client side issue. We have tried adding/removing accounts on one system which resulted in the same issue. This was a very long and slow process due to the sheer volume of emails (20gig+ from most users). We have tried reinstalling outlook restoring accounts from back-ups which has not resolved the issue. We also tried upgrading one system from outlook 2007 to outlook 2010 which, again, did not resolve the issue. We have experienced issues with a lot of emails disappearing during the copy-over process in which I'm not convinced it was the best route of migration, but nonetheless we are where we are. Can anyone suggest potential avenues of solutions to resolve this issue? Thank you. Systems: Windows 7 (10 systems) Windows XP (2 systems) Outlook 2007 (2 systems) Outlook 2010 (7 systems) Problem Outlook systems: Windows XP, Outlook 2007 x 1 Windows 7, Outlook 2007 x1 Windows 7, Outlook 2010 x 2

    Read the article

  • Windows 7 disk backup and clone for deployment to multiple systems

    - by gregmac
    I'm in the process of deploying some new PCs (there's only 8), all identical hardware. What I'd like to do is install Windows 7 (64bit), join to domain etc, install a bunch of other software, and then clone that drive to multiple other machines. I'd also like to be able to use it as a backup image, so the machine can be restored back to that image at some future date. I understand this involves at least sysprep, but I am confused after reading some tutorials that talk about using Windows Automated Installation Kit, or hacks with the registry and custom-build batch files. This process seems overly complex to me: I did something similar 10+ years ago, and and don't remember it being this bad. Surely things have improved in a decade? There's also some products that involve having network servers running deployment software, network boot, etc etc.. this is way more than I want to set up. My systems are all identical hardware. Is there a simplified way to clone PCs? Preferably (since I'm a lazy developer, and not an IT admin) I'd like to find some off-the-shelf product that I can run after I get the machine setup, that will spit out a bootable DVD I can run on all the other systems, which will boot up, ask for a computer name, join it to the domain, and that's it. Does such as product exist?

    Read the article

  • run as dialog always pops up

    - by user12006
    I recently got some malware on a machine that I don't use for much (partly intentional). I've cleaned it, but now everytime I open any .exe the 'Run As' dialog pops up asking me which user I want to use to run the program. What causes this, and what's the fix for it? edit My process to remove the malware was as such: Disconnected from the network Deleted DisableTaskMgr reg key Inspected with Process Explorer and Task Manager and noticed that all applications were being run within another executable located in Documents and Settings...\Temp\Some.exe The system tray application was also in Documents and Settings...\Temp\SomeOther.exe I suspected that a service was in place as the system tray application would restart if it was killed, but couldn't find any service that I didn't recognize. Removed permissions from Some.exe and SomeOther.exe (on those files only) Restarted and deleted Some.exe and SomeOther.exe Deleted startup entries that were created Ran AVG Free and Windows Defender to remove anything else (they would be killed immediately before the two .exe's were removed) Cleaned registry via CCleaner note that system restores would finish saying something to the effect of 'couldn't restore system: there were no changes made'. I attempted to restore to a week ago, and I only got the malware yesterday.

    Read the article

  • Makecert.exe hangs

    - by Robert
    I was following the steps in Scott Hanselman's blog post describing how to create a certificate authority and code signing certificate for PowerShell scripts. Initially, I created the certificate authority and a personal certifcate and used it to sign a powershell script successfully. All went as described in the blog post. The problem starts (as most do) when I did something that was (probably) stupid, although it seemed reasonable at the time. I wanted to start over and repeat the process again with a clean slate, so from the mmc certificates snap-in console, I deleted the personal certificate and the certificate authority I created previously. After that any time I try to use makecert, (just as I did the first time around), makecert either hangs or faults (which prompts to end or debug). Did I hose something up by deleting via the certificates snap-in? It didn't complain or warn me that it could be potentially hazardous. Is this just coincidence and something else entirely could be hosed? I have Event Log entries from the times when makecert crashed, which all look very similar; here is one: Log Name: Application Source: Application Error Date: 8/5/2009 3:55:04 PM Event ID: 1000 Task Category: (100) Level: Error Description: Faulting application makecert.exe, version 6.0.6000.16384, time stamp 0x4545910b, faulting module ntdll.dll, version 6.0.6002.18005, time stamp 0x49e03821, exception code 0xc0000005, fault offset 0x00067409, process id 0xe58, application start time 0x01ca160efdf30625. Anyone have any ideas as to what exactly caused this and/or what I can do to fix it. I'm on 32-bit Vista Enterprise w/SP2.

    Read the article

  • Is it possible to be a professional studying on your own?

    - by Marc Jr
    I read economics at university(nothing to see with linux, isn't it? :P). I have some basic knowledge about booting process, Linux Kernel compiling from source and stuff like that. But of course I have still much to learn sometimes some errors appears and "voila" I am lost. I had: Ubuntu, Fedora, OpenSuse, Arch.. using Gentoo now. I'd like to know what you linux users, professionals, administrators... would think it is the best way to learn linux in a professional way. Is it worth studying it and passing the LPIC test enough to work in the linux world? or do I need going to IT uni? I've heard LFS is a good way of learning about linux, is that real? I've been thinking about getting to LFS learn about more deeply about the linux process and learning scripts. It is possible to do this way? if anyone has a tip or a good way of doing, maybe someone did it. Any tip is very welcome. Words from a person in love with linux. :D The best, Marc

    Read the article

  • Windows Vista: Screen remains darkened for 30-60 seconds *after* UAC prompt

    - by sf2k
    Fixing someone's Vista computer. Process: I click any program or process that opens a User Account Control prompt. Screen goes dim so you may hit Continue to perform a secure user action. I click Continue Screen goes black for 30 seconds to 1 minute while you wait for the screen to return. In another example I click Cancel and screen still then goes black for 30 seconds to a minute. In that timeframe a chime goes off while you wait. (No chime if it was being cancelled.) Then screen comes back to continue with whatever. Something is occurring after the UAC prompt. Considering everything is practically a UAC acceptance this can get pretty annoying pretty quickly. Laptop has external monitor to regular external plug. Works fine. Laptop also has USB IOGEAR additional external video card. This is problematic but when unplugged same above behaviour occurs. I've ruled out monitor interference since same blackout after the UAC prompt appears with external monitors plugged in or when rebooted with no external monitors. Any suggestions on how to address this problem?

    Read the article

  • "postgres blocked for more than 120 seconds" - is my db still consistent?

    - by nn4l
    I am using an iscsi volume on an Open-E storage system for several virtual machines running on a XenServer host. Occasionally, when there is a very high disk I/O load on the virtual machines (and therefore also on the storage system), I got this error message on the vm consoles: [2594520.161701] INFO: task kjournald:117 blocked for more than 120 seconds. [2594520.161787] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [2594520.162194] INFO: task flush-202:0:229 blocked for more than 120 seconds. [2594520.162274] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [2594520.162801] INFO: task postgres:1567 blocked for more than 120 seconds. [2594520.162882] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. I understand this error message is caused by the kernel to inform that these processes haven't been run for 120 seconds, most likely because a disk access to the storage system has not yet been processed. But what is the effect on the processes. For example, will the postgres process eventually write its data when the storage system is idle again after a few minutes, so that all data is still consistent? Or will it abort the write, leaving some tables in an inconsistent state? I certainly expect that the former should be the case - if the disk access is slow, postgres (or any other affected process) should just wait as long as it takes. I can live with the application hanging for a few minutes. But if there is a chance for data corruption then any of these errors is really bad news. Please advise what to do here.

    Read the article

< Previous Page | 277 278 279 280 281 282 283 284 285 286 287 288  | Next Page >