Search Results

Search found 11135 results on 446 pages for 'thread safe'.

Page 281/446 | < Previous Page | 277 278 279 280 281 282 283 284 285 286 287 288  | Next Page >

• Vista failing to load after apparently being repaired

  - by Joomaz

  Hi, I apologise if I'm a litre vague and can give more info if needed. My vista machine has been working fine until today when I tried booting it. Vista loads showing the loading bar then goes to a black screen with the cursor on which you can move. It then remains like this for several minutes, during this time the computer doesn't sound like it's doing much, it is relatively quiet. Finally the welcome screen appears. It stays on this for several minutes again and the computer reboots. This keeps happening and the machine fails to load in safe mode - the same happens. I booted the pc with the vista disk in and ran repair your computer and used the system repair. It took about 20 minutes saying it was repairing damaged giles. I booted the pc again and the same happened. I loaded the pc with yeh vista disk again and chose repair my computer again. System repair seemed to run automatically this time and agian it did the same. I rebooted and the problem persisted. I then tried system restore to a few days ago. After half a hour as it finished it said it failed due to a portion being corrupt. I am really not sure what to do now. Any advice appreciated!

  Read the article

• Does a 3ware "ECC-ERROR" matter on a JBOD when I have ZFS?

  - by Stefan Lasiewski

  I have a FreeBSD 8.x machine running ZFS and with a 3ware 9690SA controller. The 3ware controller shows an ECC-ERROR with one of the disks: //host> /c0 show VPort Status Unit Size Type Phy Encl-Slot Model ------------------------------------------------------------------------------ p0 OK u0 279.39 GB SAS 0 - SEAGATE ST3300657SS p1 OK u0 279.39 GB SAS 1 - SEAGATE ST3300657SS p2 OK u1 931.51 GB SAS 2 - SEAGATE ST31000640SS p3 ECC-ERROR u2 931.51 GB SAS 3 - SEAGATE ST31000640SS p4 OK u3 931.51 GB SAS 4 - SEAGATE ST31000640SS /c0 show events shows no ECC errors in it's recent history. ZFS does not currently detect any errors. zpool status says No known data errors My question: Is this ECC-ERROR something that I need to be concerned about? According to the 3ware CLI 9.5.2 Manual, an ECC-ERROR means that the 3ware controller caught a read-error for one or more sectors on this drive. This sometimes occurs when a RAID array is recovering from a failed disk. I believe that ECC-ERRORS can also be detected when the 3ware Controller verifies each disk. None of the drives have failed and thus there was no drive rebuild, so I assume that 3ware discovered a bad sector when it ran it's weekly auto-verify scan of the disks. Is this a safe assumption? According to our logs, ZFS has not detected any bad sectors on this drive. ZFS can work around read errors -- if ZFS detects a bad sector on the drive, it will simply mark that sector as bad and never use it again. From the ZFS perspective one bad sector isn't a big deal, although it might indicate that the drive is starting to go bad.

  Read the article

• Should I persist images on EBS or S3 ??

  - by enes

  Hi; I am migrating my Java,Tomcat, Mysql server to AWS EC2. I have already attached EBS volume for storing Mysql data. In my web application people may upload images. So I should persist them. There are 2 alternatives in my mind. 1- Save uploaded images to EBS volume. 2- Use S3 service. The followings are my notes, please be skeptic about them, as my expertise is not on servers, but software development. EBS plus: S3 storage is more expensive. (0.15 $/Gb 0.1$/Gb) S3 plus: Serving statics from EBS may influence my web server's performance negatively. Is this true? Does Serving images affect server performance notably? For S3 my server will not be responsible for serving statics. S3 plus: Serving statics from EBS may result I/O cost, probably it will be minor. EBS plus: People say EBS is faster. S3 plus: People say S3 is more safe for persistence. EBS plus: No need to learn API, it is straight forward to save the images to EBS volume. Namely I can not decide, will be happy if you guide. Thanks

  Read the article

• Cleaning a proxy/phishing trojan from Windows XP computer

  - by i-g

  I am trying to remove an interesting trojan from a Windows XP computer. It manifests itself as a phishing page (screenshot linked) that appears after the user tries to log on to eBay. So far, I haven't found any other web sites that are affected. As you can see, the trojan intercepts browser connections (all installed browsers are affected) and injects this phishing page. The address looks like it's ebay.com, but HTTPS verification doesn't work (no lock icon or green bar in Firefox.) At some point, Trojan.Dropper appeared on the computer. I removed it with Malwarebytes Anti-Malware. Although it reappeared several times, it seemed to be gone after I booted into Safe Mode and did a full system scan with MBAM. Now, however, a different trojan has appeared on the machine; I suspect it was installed by Trojan.Dropper. So far, MBAM, Ad-Aware, and Spybot S&D have been unable to remove it. I've looked for it in the HijackThis log but haven't found anything conclusive. Has anyone run across a trojan like this before? Where would I start looking for it to remove it manually? Thank you for reading.

  Read the article

• Windows XP, Preference menu's hidden for many programs

  - by Jestep

  I don't know when this started happening, but it has been several months since I first noticed it. Basically, when I go to a preferences menu of some programs, the preferences window is completely hidden, but the program see's it as being open. This prevents me from interacting with the preferences and the actual program. So far I've noticed it on Adobe Illustrator and Netbeans. Illustrator when I select edit - Preferences - An Option. On Netbeans it happens when I right click on a site and select properties. Here's a link to a screen shot after I click on the preferences menu (I don't have enough points to post an image yet): http://www.jestep.com/images/screen-2.jpg. Note that the main workspace is grayed out. I have to hit Escape to close the hidden preferences window. I've tried unstinstalling, completely wiping the registry of any trace of the program and reinstalling. Thought it may have been a multi-monitor issue when I switched from 2 monitors down to 1, but menu's were not on other monitor when I plugged one back in. I've reset workspaces, windows display, windows performance settings, changed resolution, safe mode, everything I can think of. I cannot figure out what would cause the same problem on completely unrelated software, and I cannot reset it by reinstalling. Any help would be greatly appreciated.

  Read the article

• Windows 7 hangs while loading desktop

  - by Joshua

  I am facing a weird problem. My computer hangs while loading the desktop, and only the background shows up; no icons or bars load. If I power the system on and off about 4-6 times, I may be able to use it normally. The desktop loads normally after rebooting or in safe mode; this only occurs when I start the system normally. I've tried several things to fix it, such as removing all start-up items, but it still doesn't solve the problem. What should I do? I found three major errors in Event Viewer: Source: Microsoft-Windows-DistributedCOM Level: Error DCOM got error "1084" attempting to start the service WSearch with arguments "" in order to run the server: {7D096C5F-AC08-4F1F-BEB7-5C22C517CE39} Source: Microsoft-Windows-DistributedCOM Level: Error DCOM got error "1084" attempting to start the service WSearch with arguments "" in order to run the server: {7D096C5F-AC08-4F1F-BEB7-5C22C517CE39} Source: Service Control Manager Level: Error The Network List Service service depends on the Network Location Awareness service which failed to start because of the following error: The dependency service or group failed to start.

  Read the article

• Windows - Website unaccessible only on windows pcs in LAN

  - by DorentuZ

  For serveral days now, a website isn't accessible on a single pc in the LAN. On the other pc's, it works just fine. And it's just a single website that's not accessible as far as I know of. The website generates a timeout on every single web browser I've tried (IE8, Firefox and Chrome). However, traceroute, nmap and telnet all work just fine. I've even tried multiple user accounts and safe mode, but that didn't work either. As a side note: using a linux live cd did work and I could access the website without any problems. The hosts file is the windows default, the ip- and dns settings on the network adapter normal as well. No strange processes are running and no viruses found. According to tcpview and netstat there are connections to the domain, but every request in the browser results in a timeout.. Any idea what's happening? Update: All of the computers on the network running Windows (any version) are showing this problem now. The website is still working under linux and mac osx. So, it has to be related to some kind of windows update (although I haven't installed any on one computer in the past week, which I've set to do manual updates only)..

  Read the article

• Need help diagnosing my machine

  - by Tom Collins

  I have something that just slows my computer to a crawl sometimes. Not running anything big. Yesterday all I had running (besides background apps) were Firefox & Windows Explorer and could barely even switch screens. Nothing showing up in the task manager as hogging CPUs. I have all non-essential services stopped (MySQl & MSSQL) unless I need them. I made some restore points not long ago, but they disappeared. This is a development mach with a LOT of apps installed, so I really, really do not want to re-install Windows. So, what I'm looking for are ideas or tools I can use to help diagnose this problem. The only clues I have is this started right after I installed Office 2013 (with Office 2010 still installed as well) installed Visual Studio 2012 (also keeping 2010 as a co-install) and installed MSSQL 2012 (upgrade from 2008, no co-install) Also, computer runs fine in Safe Mode. I've just ran out of ideas of what to check. Any help / suggestions would much appreciated. Thanks P.S. I'm running Win 7 Pro (x64). Office is also 64 bit. Visual Studio & MSSQL are 64 bit if that option was available (not sure).

  Read the article

• DNS zone file SPF configuration to support sending mail from multiple servers and gmail

  - by Tauren

  I want to configure SPF on a domain to allow mail to be sent from: the x.com website server (x.com and www.x.com - both at same IP) it's MX servers (smtp.x.com, mx.x.com, mail.x.com) another server that isn't listed as an MX server (somehost.x.com) via gmail using an account that has authenticated use of [email protected] Will this zone file work? If not, what are the problems with it? $ttl 38400 @ IN SOA ns1.x.com. hostmaster.x.com. ( 201003092 ; serial 8H ; refresh 15M ; retry 1W ; expire 1H ) ; minimum @ NS ns1.x.com. @ NS ns2.x.com. @ MX 10 mx.x.com. @ MX 20 smtp.x.com. @ MX 30 mailhost.x.com. ; SPF records @ IN TXT "v=spf1 a mx a:somehost.x.com include:_spf.google.com ~all" mx IN TXT "v=spf1 a -all" smtp IN TXT "v=spf1 a -all" mailhost IN TXT "v=spf1 a -all" Questions: Is _spf.google.com the right thing to include for gmail.com, or is it only for Google Hosted Apps? If only for Google Apps, what should I include to send from gmail.com? If mail shouldn't be sent from anywhere else, is it safe to use -all instead of ~all? Does it make sense to add specific SPF records for each of the mail servers? Any other problems with the zone file? I want to confirm these things before making changes to my zone file. The file has SPF configured basically the same now, just without google.com and somehost, but I want to make sure I won't break things when I change it.

  Read the article

• Portable USB drives hidden pertition - New request

  - by ZXC

  This question was made by Francesco on Jul 29 '11 at 17:14. and the replies were not satisfactory due they not point to an important problem that´s: Why could anyone want to make certain data only accesible for a program but not to the users?. For example: If I want to do a safe distribution of original music for demostration purposes I will need several requisites: 1) The music should be heard using a simple procedure like selecting the name of each song on a playlist of a mediaplayer. 2) The portable media, ussually a portable USB drive, must hide for complete and should make unaccesible the files that contain the audio data to anything but the mediaplayer, that must be in the first partition, the one that is visible. 3) Considering that´s impossible to really hide files in a non-hidden partition, a second hidden partition should be created in the USB drive and the audio data will be stored there. 4) The trick is to read the audio data files stored in the hidden partition with a mediaplayer stored in the visible partition, the media player also should be a complete standalone program and independent from any library of the operating system except of the OS audio system. 5) The hidden partition should have a copy protection scheme that could impede to do copies of the data or create working ISO images of it. I know that this description could not be technically accurate but it has a complete logic from the needs of a music producer against the problem of piracy. The philosophy that surrounds the concept is to transform a virtual object like a digital string of audio in a solid object like the analog vinyl discs are.

  Read the article

• What speed are Wi-Fi management and control frames sent at?

  - by Bryce Thomas

  There are a bunch of different 802.11 Wi-Fi standards, e.g. 802.11a, 802.11b, 802.11g, 802.11n etc. that all support different speeds. Wi-Fi frames are generally categorised as one of the following: Data frames - carry the actual application data Control frames - coordinate when its safe to send/reduce collisions Management frames - handle connection discovery/setup/tear down (e.g. AP discovery, association, disassociation) My question is about whether all these frames, and specifically management frames, are transmitted at the fastest supported speed available, or whether certain classes of frames are transmitted at some lowest common denominator speed. I have noticed that when I put an 802.11b/g only device into monitor mode and capture traffic over the air, I still see management frames (e.g. association/disassociation) being transmitted between my phone and AP which are both 802.11n, even though 802.11n has a higher transfer rate. So I am imagining one of two possibilities: My 802.11n phone/AP had to negotiate a slower speed for some reason and that's why I can see their frames on my 802.11b/g monitoring device. Management frames (and perhaps control frames also?) are sent at a lower speed, and it's only data frames that are transmitted faster with newer 802.11 standards. The reason I would like to know which one of these two possibilities (or perhaps a third possibility) is the case is that I want to capture management frames, and need to know whether using an 802.11b/g card is going to lead to me missing some frames sent at higher speeds than the monitoring card can observe. If management frames are indeed sent at a slower rate, then it's all good. If I just happen to be seeing the management frames because my phone/AP have negotiated a slower rate though, then I need to reconsider what card I use for packet capture.

  Read the article

• Encryption setup for Linux NAS?

  - by Daniel

  There's a bazillion hard disk encryption HOWTOs, but somehow I can't find one that actually does what I want. Which is: I have a home NAS running Ubuntu, which is being accessed by a Linux and a Win XP client. (Hopefully MacOS X soon...) I want to setup encryption for home dirs on the NAS so that: It does not interfere with the boot process (since the NAS it tucked away in a cupboard), the home dirs should be accessible as a regular file system on the client(s) (e.g. via SMB), it is easy to use by 'normal' people, (so it does not require SSH-ing to the NAS, mount the encrypted partition on command line, then connecting via SMB, and finally umount the partition after being done. I can't explain that to my mom, or in fact to anyone.) does not store the encryption key the NAS itself, encrypts file meta-data and content (i.e. safe against the 'RIAA' attack, where an intruder should not be able to identify which songs are in your MP3 collection). What I hoped to do was use Samba + PAM. The idea was that on connecting to the SMB server, I'd have to enter the password on the client, which sends it to the server for authentication, which would use the password to mount the encrpytion partition, and would unmount it again when the session was closed. Turns out that doesn't really work, because SMB does not transmit the password in the plain and hence I can't configure PAM to use the incoming password to mount the encrypted patition. So... anything I'm overlooking? Is there any way in which I can use the password entered on the client (e.g. on SMB connect) to initiate mounting the encrypted dir on the server?

  Read the article

• No OS will boot, all freeze

  - by Gyan

  This is for a computer with the following configuration: Asus P5KPL-AM/PS motherboard Pentium D 820 (dual core 2.8 GHz) 1 x 2 GB DDR2-800 Transcend RAM 1 SATA2 Samsung 160 GB HDD 1 PATA LG CD/DVD Writer PS/2 generic Keyboard USB Razer mouse The computer was working fine till a month ago with a Hitachi HDD in place of the Samsung. But that drive died and I sent it in for warranty replacement. Since then and till last week, the computer had not been turned on. I then got hold of a spare but XPSP2-loaded Samsung drive from another computer and decided to get this computer temporarily running. However, when I tried to boot into XP, it didn't load. It got stuck at the first graphical screen. When trying Safe Mode, the file list would be updated up to diskio.sys and then freeze. If I tried to boot Kubuntu off a CD, I would get past the first menu, but then get stuck at the subsequent graphical interface in the loading process. A similar thing happend with a friend's Windows XP-on-a-pen-drive. I switched the RAM into the other slot, but no luck. Then I booted the Ultimate Boot CD and ran Memtest86+ and a couple of the bundled CPU stress tests but these detected no errors. Some searching on the Internet brought up the notion of the CPU failing to switch from "real" to "protected mode". I'm hoping to get a fix on what the problem is and what I can do about it. Edit: I've flashed to the latest BIOS, but that doesn't help. Also, Knoppix LiveCD also freezes. I notice that the LED in my mouse goes off at the time of freeze, but trying to boot without the mouse connected produces the same result.

  Read the article

• Google chrome not accepting any security certificates

  - by Jerry

  I've recently developed a problem with Google Chrome that's really annoying. I'm using Firefox at the moment with no problems whatsoever and it's the same with IE, so it's safe to say this problem is specific to Chrome. The problem is that it's not accepting security certificates from certain sites. I suppose the best place to start would be google itself. I can't search. The google search page will load but when I type some search term into the search box and hit 'search' I get the message: "You attempted to reach www.google.com, but the server presented an invalid certificate. You cannot proceed because the website operator has requested heightened security for this domain." No matter what the search term is, this is the result. Also when I try to log in to facebook - same message. Youtube works and many other sites that I know present security certs so I'm baffled. I've searched and there are other people who have had similar issues but I can't find a solution anywhere. The most common answer I'm picking up for this is to "check your system time" but I can safely say that it's not my system time. If anyone knows what is going on, I'd very much appreciate being informed. It's not super urgent as I can use Firefox to access those places Chrome won't, but it IS super annoying because I can usually sort out issues like this in no time.

  Read the article

• Upgrading openSUSE 11.1 with Plesk Panel 9.3 to PHP 5.3

  - by Jonathan Hogervorst

  Hello, I'm running a VPS with openSUSE 11.1 (i586). On the VPS is Parallels Plesk Panel 9.3.0 installed. The current PHP-version is PHP 5.2.11. I want to upgrade PHP to PHP 5.3, but I can't find good instructions on how to do this. If I check for updates in Zypper, it says this is the latest release. In the Plesk Updates isn't an update either, both via the webbased interface and the command line interface. On Software.openSUSE.org I can find packages for PHP 5.3.1 in both the server:php/server_apache_openSUSE_11.1-repo and the server:php/openSUSE_11.1-repo (can't post the link because I'm a newbie here). But if I add one of those to Zypper, I still don't see an update. Is there here somebody who knows how to do this? And is it completely safe to update that way? I don't want to end up with a broken VPS... Thanks! Jonathan

  Read the article

• Replacing stock Core 2 Duo heatsink fan (just the fan really) with a Dell CPU fan

  - by user647345

  My old heatsink fan broke and I'm trying to reconnect its plugs to a new fan. My Dell CPU fan has some custom Dell plug. I snipped the old fan's wire in half and kept the plug on the end of it. I want to connect it to the Dell fan wire to the plug. The motherboard is a P5Q-e, the stock Core 2 Duo fan was .20A and the dell is .70A. Is that going to matter? The wire from the fan has four wires, the wire with the plug has four wires. They share three, of the four colors: red, black, and blue. Dell's fourth wire is white, while the plug's fourth wire is yellow. Is it safe to assume that I just connect the yellow and the white plug together and match the rest up? I don't want to take any risk of damaging anything. It runs fine passively without a fan, but I have speedstep on, so I would like to use this fan and just fasten it to the heatsink with some twist ties and paperclips and call it a day.

  Read the article

• Skydrive for desktop not showing icon in notification area

  - by jeruntime

  is this normal behavior? I'm concerned that some files will not be transferred. For example. I need to be sure that its safe to put my laptop to sleep so that later when I'm on my desktop I wont have to open up my laptop and sync again if I closed it too early. It doesn't even appear when I THINK it is syncing. Thanks for any help in advance. edit 1: Yeah I know the app isn't required or even offered anymore, but what I was wondering was if they had some way to tell if it's syncing or not. The old desktop app had an icon in the notification area which had a animation for when it was syncing, but now there isn't anything there. Although when I try to go in and make it appear it says the application isn't active and the icon will show the next time it is. Its version is 17.0.2015.0811 Is it possible to force the icon to show in the notification area if it isn't designed to show up there at all? I basically just want the same functionality of Skydrive on windows 8.

  Read the article

• Windows installation repair option not showing up

  - by Jason

  I'm trying to repair an existing Windows XP installation. Following the instructions from http://www.microsoft.com/windowsxp/using/helpandsupport/learnmore/tips/doug92.mspx this should work: - 1.When the Press any key to boot from CD message is displayed on your screen, press a key to start your computer from the Windows XP CD. - 2.Press ENTER when you see the message To setup Windows XP now, and then press ENTER displayed on the Welcome to Setup screen. - 3.Do not choose the option to press R to use the Recovery Console. - 4.In the Windows XP Licensing Agreement, press F8 to agree to the license agreement. - 5.Make sure that your current installation of Windows XP is selected in the box, and then press R to repair Windows XP. - 6.Follow the instructions on the screen to complete Setup. On step 5 pressing R does nothing and there is nothing on the screen saying it would. When I just select to install I get a message that a previous installation is there and proceeding will destroy it and installed applications, I can optionally select a directory other than c:/windows, and I can optionally format before continuing. I had tried to go from SP2-SP3. It failed, and then I couldn't get to Safe Mode. I put the SP1 disk back in to do a repair, and I don't see that option. (I don't have an SP2 boot/install disk, I just have the non-boot upgrade package.)

  Read the article

• Mustek 1200 CP driver SFC4.SYS bluescreens with BAD_POOL_HEADER

  - by Slink84

  I have Windows XP SP2. Recently it started bluescreening right after starting up with 'BAD_POOL_HEADER', 0x00000019 error caused by SFC4.SYS driver. After googling for a while I've found out that this is my Mustek's 1200 CP scanner driver. Booting in safe mode and uninstalling it solved the problem... And created another one: now I can't use my scanner. The weird thing is, that it has been working for a while on this PC without any problems. It all started suddenly, and I can't remember installing anything that might have affected it. Reverting to several earlier system restore points didn't help. I've tried re-installing it from the Mustek website, just in case if my copy got corrupted or infected by a virus, but it did not help - it still bluescreens. Also, I've installed Avast and scanned my PC - there were no viruses found. If anyone had such a problem before or has an idea what might have caused it, please help. ED: @Michael Todd: ...try installing on another PC... I've installed it on my friends PC. He has the same OS version, with the latest updates just like mine (he wasn't too happy, even after I've assured him that it is easy to fix by uninstalling that driver :] ). It worked fine - no bluescreens or whatsoever. So I think I've narrowed it down to either BIOS settings, or some wicked driver conflict. Next thing I'm going to try is to re-install XP, or install windows 7. I'm not too happy with a prospect of mucking about with BIOS settings...

  Read the article

• VMWare Newbie - looking for hardware recommendations and help :) [closed]

  - by Dan

  I am looking for some hardware recommendations on an upcoming virtualization project. We are a small company (80 users - 25 in site 1, 55 in site 2) currently using Windows Server 2003 - no VM servers yet. Our AD is setup where site 1 is the root domain and site 2 is a subdomain/subnet - connected by T1 and VPN for failover. The current DC's also server as file servers, print servers, AntiVirus servers. Email is in the cloud. Additionally then in site 1 we have 3 additional member servers - one running IBM Websphere for a customer specific app, one running Infor PowerLink (no real heavy load) and another that we use for Virtual Studio apps and also runs DirSync for Exchange Online. No heavy workloads on any of these machines really. We also have an AS400 box that we run ERP/CRM software on that site 2 connects to over the WAN link. In site 2 we also have a SQL machine that runs on Win2K server. Database files are not large less than 5 GB. Light to Medium workload on this machine. File servers in each site store less than 500 GB data and probably won't grow to more than 1TB in the next 5 years. I am looking to go to VMWare in both sites and virtualize all servers. What recommendations do you have for server, storage hardware? Is it safe to virtualize all of your DC's? Any help or advice would be greatly appreciated. Thanks.

  Read the article

• Android failure to boot on LG [migrated]

  - by Ukavi

  I need to recover data from my AT&T LG Thrill Android Phone Background: My AT&T LG Thrill phone's battery died a couple of days ago because I forgot to charge it. When I charged the phone and tried to turn it on, it showed the LG logo followed by the dropping balls and the AT&T "Rethink Possible" screen. I then get a mesage that the Application Google Services Framework has crashed and the phone goes into a loop with the dropping balls showing again followed by "Rethink Possible" screen. This sequence repeats itself over and over and the phone does not get out of this loop. I have been able to go into the recovery screen (both Safe Mode and the Android Recovery Service) and have cleared cache, etc. However, I DO NOT want to wipe user data and restore to factory settings as this will wipe all of my data (pictures, application data, etc). Solution Needed: I need a suggestion to a way of accessing my data so that I can back it up onto an SD card/computer. I DO NOT want to root the phone as this may void the warranty. What I'm looking for is a way of perhaps putting the original flash image on the micro SD card and then have the phone read that image. Or some other similar solution that will get the phone out of this loop and allow me to get to the data.

  Read the article

• Windows XP restarting repeatedly after a fresh restore

  - by DWilliams

  I don't normally deal with Windows but someone wanted me to fix their computer with Windows XP on it. It was just restarting every time it tried to boot. It would not go into safe mode, the result was the same regardless of the selected mode. The computer is like 4 years old and has been running the same installation for that entire time, so I figured the easiest solution was just to back up their files and re-install. I loaded the computer up with a live CD and copied their files off to a USB drive, then proceeded to run HP's "factory restore" feature (which I'm not particularly fond of, I'd rather have a disk to install from than reload all the crapware HP gets paid to install for you). It restored, and I put all their files back, installed their programs, and started the full windows update process. Everything seemed great so I left and told them what to do once it finished. A few hours pass, and my phone rings. Apparently it started doing the exact same thing as before once the updates finished. I don't have the computer sitting in front of me now so I can't really provide any more information than that. What could be causing this and, more importantly, how do I fix it? The fact that the same problem resurfaced after the restore makes me think it's either a hardware problem or an update breaking the computer.

  Read the article

• How to repair Mac OS X without reinstalling?

  - by RahulVyas

  I have an Intel PC. I have installed iDeneb Mac OS X in my PC. It's running fine. After that I thought about installing Snow Leopard for running the iPad SDK. So I bought a retail Snow Leopard and booted it with Rebel EFI boot loader. When I was installing Snow Leopard, at the end of installation, setup gives an error. So I restarted my PC and boot with Rebel and I saw that the Mac was there so I booted that into safe mode and Mac OS X runs. After that I installed iPad SDK. But when I try to create an application, Xcode is not responsive. It hangs when I choose new project, give it a name and save it on disk. After just as I gave name and choose save it hangs. Is there any way I can repair my Mac OS X without reinstalling? I have also been unable to boot into normal mode and also without Rebel CD. So I want to boot without Rebel CD and also want to run iPad SDK.

  Read the article

• It takes a long time until Windows XP recognize I connected USB drive

  - by Pavol G

  I have a problem with my new USB disk. When I connect it to my laptop with Windows XP SP2 it takes about 4-5min until Windows recognizes it and shows it as a new disk. I can also see (disk's LED is blinking) that something is scanning the disk when I connect it; when this is done Windows immediately recognize it. Also when I'm copying data to this disk the speed is about 3.5MB/sec. It's connected using USB2.0. I tried to check for spyware (using Spybot), also tried running Windows in safe mode. But still have the same problems. Do you have any idea what could help to solve this problem? On Windows Vista (another laptop) everything is ok, disk loads in about 15sec and speed is about 20-30MB/sec. Edit: I tried to update to SP3 - no change Edit2: When this "strange" scanning occurs I can see that DPCs process is taking about 50% of CPU. When the scan ends (after 5min) this process take 0% again. Edit3: About the scan time, currently it's taking about 5min, but this time is growing as I'm adding more data to the disk, currently its about 40GB and I don't want to see how long it will take with 1000GB. Thanks a lot for every advice!

  Read the article

• Will adding a SSD cache device to my ZFS storage improve performance?

  - by Sysadminicus

  The server has 4GB of RAM and my zpool is made up of 15.5k SAS drives arranged like this: NAME STATE READ WRITE CKSUM tank ONLINE 0 0 0 raidz1-0 ONLINE 0 0 0 c0t2d0 ONLINE 0 0 0 c0t3d0 ONLINE 0 0 0 c0t4d0 ONLINE 0 0 0 c0t5d0 ONLINE 0 0 0 c0t6d0 ONLINE 0 0 0 c0t7d0 ONLINE 0 0 0 c0t8d0 ONLINE 0 0 0 raidz1-1 ONLINE 0 0 0 c0t10d0 ONLINE 0 0 0 c0t11d0 ONLINE 0 0 0 c0t12d0 ONLINE 0 0 0 c0t13d0 ONLINE 0 0 0 c0t14d0 ONLINE 0 0 0 spares c0t9d0 AVAIL c0t1d0 AVAIL The primary use is as an NFS store for a couple VMWare ESXi servers. I can't do any "true" benchmarks because this is a production system (no budget for test systems), but using dd and bonnie++ I can't get more than ~40-50MB/s writes and ~70-90MB/s reads. It seems I should be able to do much better, but I'm not sure where to optimize. Based on what I've read, I think dropping in a OCZ Vertex 2 Pro SSD as my L2ARC is going to be the best bang-for-the-buck to improve througput. Is there something else I should be looking into to help performance? If not... How do I know how big a cache device I need? Am I safe with only a single SSD as my cache device?

  Read the article

< Previous Page | 277 278 279 280 281 282 283 284 285 286 287 288  | Next Page >