Search Results

Search found 22716 results on 909 pages for 'network architecture'.

Page 283/909 | < Previous Page | 279 280 281 282 283 284 285 286 287 288 289 290  | Next Page >

• DHCP Relay setup in ubuntu server

  - by jerichorivera

  I have a network appliance (QNO) that works as traffic load balancer and dhcp server. I would like to add a linux server in between the network appliance and the client computers. The linux server will be used to monitor bandwidth usage. My problem is I still want DHCP to be served by the network appliance so that load balancing will still work efficiently. We are afraid that if we setup the linux server as the DHCP server the network appliance will not be able to load balance the traffic if it only sees the linux server as a single client connecting to it. I've been searching all over for a tutorial on how to setup DHCP relay but have not found any. How do I setup DHCP relay on my linux server given there are two NICs attached to it, one connects the linux server to the network appliance and the other connects the linux server to the client computers. EDIT Router (DHCP) ---- [eth0] Linux Server (Relay agent) [eth1] ----- PC (network) Router IP is 192.168.0.100 eth0 is on DHCP eth1 is static 192.168.2.11 (if I need to change this I can) Tried to do dhcrelay -i eth1 192.168.0.100, but the PC was not getting any DHCP lease from the DHCP router. I might be missing something here.

  Read the article

• Debian Wheezy IPv6 isn't configured with ifup post-up hook

  - by aef

  We recently set up a server on Debian Wheezy Beta 3 (x86_64) which has a native IPv6 connection. We configured the eth0 interface to get the IPv6 configuration through some post-up hook commands in /etc/network/interfaces. The result is, that after the booting the system up, there is only IPv4 and an auto-configured link-local IPv6 address configured on the interface, as if the command has never been executed. When we additionally place the commands after the call to ifup -a inside the /etc/init.d/networking init script, everything works as expected and we have a fully configured interface after booting up. This is quite an ugly way to configure the interface. What are we doing wrong with the ifup post-up hooks? Or is this a bug? The section from /etc/network/interfaces looks like this (IP-addresses changed): allow-hotplug eth0 iface eth0 inet static address 1.2.3.1 netmask 255.255.255.192 network 1.2.3.0 broadcast 1.2.3.63 gateway 1.2.3.62 dns-nameservers 8.8.8.8 dns-search mydomain.tld post-up ip -6 addr add 2001:db8:100:3022::2 dev eth0 post-up ip -6 route add fe80::1 dev eth0 post-up ip -6 route add default via fe80::1 dev eth0 I also tried it in this alternative way: auto eth0 iface eth0 inet static address 1.2.3.1 netmask 255.255.255.192 network 1.2.3.0 broadcast 1.2.3.63 gateway 1.2.3.62 dns-nameservers 8.8.8.8 dns-search mydomain.tld iface eth0 inet6 static address 2001:db8:100:3022::2 netmask 64 gateway fe80::1 What we added to /etc/init.d/networking: … case "$1" in start) process_options check_ifstate if [ "$CONFIGURE_INTERFACES" = no ] then log_action_msg "Not configuring network interfaces, see /etc/default/networking" exit 0 fi set -f exclusions=$(process_exclusions) log_action_begin_msg "Configuring network interfaces" if ifup -a $exclusions $verbose && ifup_hotplug $exclusions $verbose # Our additions ip -6 addr add 2001:db8:100:3022::2 dev eth0 ip -6 route add fe80::1 dev eth0 ip -6 route add default via fe80::1 dev eth0 then log_action_end_msg $? else log_action_end_msg $? fi ;; …

  Read the article

• Wireless Access Point stopped working

  - by Alex Pritchard

  I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

  Read the article

• Ubuntu IP Configuration - multiple subnets & interfaces

  - by HaydnWVN

  Have a 'new' mailserver running postfix on Ubuntu. We are having some problems configuring the subnets & interfaces. Basically 2 subnets (.253. & .254.) need to be connected through the 3rd subnet (.252.) where the Router is residing. # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.62.254.199 netmask 255.255.0.0 network 10.62.254.0 broadcast 10.62.255.255 #gateway 10.62.252.138 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 10.62.252.138 dns-search ***.com auto eth1 iface eth1 inet static address 10.62.253.199 netmask 255.255.0.0 network 10.62.253.0 broadcast 10.62.255.255 #gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-nameservers 10.62.252.138 dns-search ***.com auto eth2 iface eth2 inet static address 10.62.252.199 netmask 255.255.0.0 network 10.62.252.0 broadcast 10.62.255.255 gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-search ***.com I have an external support company who are looking into this (they built and configured this server), but it's taking far too long... So I'm looking to highlight the mistake!

  Read the article

• Why is piping dd through gzip so much faster than a direct copy?

  - by Foo Bar

  I wanted to backup a path from a computer in my network to another computer in the same network over a 100MBit/s line. For this I did dd if=/local/path of=/remote/path/in/local/network/backup.img which gave me a very low network transfer speed of something about 50 to 100 kB/s, which would have taken forever. So I stopped it and decided to try gzipping it on the fly to make it much smaller so that the amount to transfer is less. So I did dd if=/local/folder | gzip > /remote/path/in/local/network/backup.img.gz But now I get something like 1 MB/s network transfer speed, so a factor of 10 to 20 faster. After noticing this, I tested this on several paths and files and it was always the same. Why does piping dd through gzip also increase the transfer rates by a large factor instead of only reducing the bytelength of the stream by a large factor? I'd expected even a small decrease in transfer rates instead, due to the higher CPU consumption while compressing, but now I get a double plus. Not that I'm not happy, but just wondering. ;)

  Read the article

• Query specific nameserver for a particular domain upon VPN connect

  - by MT

  Some background: I have a work laptop with Ubuntu 9.10 on it. I have a small network at home where I've been running some basic services (for myself/my family) for 10 some years. In my home network there is a nameserver (Fedora) running Bind 9 with two "views". One view is the "outside" view and it provides name resolution (to the Internet at large) for email, a wiki, and a couple of blogs. The "inside" view provides name resolution (to the internal RFC1918 addresses of theses servers) as well as all the inside hosts, network equipment, ...etc. I connect with an openvpn client to my home network from outside (such as work). What I'd like to be able to do is resolve names on my internal network across this VPN (so I get the RFC1918 "inside" responses) without fully changing my resolver to the DNS server at my hose. For example, if I connect to the VPN from work, I can change my resolver (by editing resolv.conf) to the DNS server at my house (across the VPN) and then successfully resolve all of the inside DNS names on my home network. The issue I have with this is that now I'm no longer able to resolve "inside" names provided by my work's DNS servers (because I'm using my home DNS server). Alternatively, I can connect to the VPN and access my home severs via IP addresses directly, but this is inconvenient and causes issues with Apache name-based hosting (among other things). In the end, the effect I'm trying to achieve is as follows: When I connect to the VPN I automatically start sending DNS requests for *.myhomedomain.com to my home nameserver, but any other requests continue to go the the nameserver I was using before (the one I received on my company LAN via DHCP). When I disconnect the VPN, requests for *.myhomedomain.com go back to the local LAN DNS server (e.g. all requests are going there now). I'm looking for suggestion at to how this can be accomplished.

  Read the article

• What can be done to improve time synchronization on networks with sporadic internet access?

  - by anregen

  I'm looking for advice setting up time servers for a very non-typical network. I support many closed networks that have occasional access to the internet. A network would get access most days for a few hours, but would frequently go 1-3 weeks blacked-out. The computers/servers on this network are mostly *nix-based, but not all the same flavor. The entire network is mobile, so when it connects, it will have very different hops/latency to internet time servers. The servers on the closed network are powered-off frequently (at least daily). Right now, my gut tells me to use NTP (because I hate re-learning all the stuff that someone else already got working pretty well). But I have several issues, and am looking for someone with experience in this type of strange situation. I currently have no solution in place, I'm simply letting the internal clocks drift. This results in errors of ~600s in a majority of networks. I have seen mismatch worse than 10,000s. Is there something "better" than NTP in this situation? I know NTP likes to have very frequent, consistent access to servers that give nearly identical answers. I won't have that. How many internal NTP servers should I configure, so that during periods of internet blackout, I have internal time that is consistent within the closed network? There is no human access. No matter how large the mismatch, the server(s) must attempt to correct itself. Discrete steps are very bad. No matter how large the mismatch, the correction must be "slewed", not "stepped". I understand that this could take many hours to correct.

  Read the article

• Configuring WPA WiFi in Ubuntu 10.10

  - by sma

  Hello, I am trying to configure my wireless network on my laptop running Ubuntu 10.10 and am having a bit of difficulty. I am a complete Linux newb, but want to learn it, hence the reason I'm trying to set this up. Here's the vitals: It is a Gateway 600 YG2 laptop. It was previously running Windows XP, but I installed Ubuntu 10.10 in place of it (not a dual boot, I removed XP altogether). I have an old wireless card that I'm trying to resurrect. I haven't really used the card in a couple years, but it seems to still work, I just can't connect to my home's wireless network. The card is a Linksys WPC11 v2.5. When I plug it in, Ubuntu recognizes the network, but won't connect to it. My home network uses WPA encryption and the only connection type that Ubuntu's network manager is giving me is WEP and then it asks for a key -- I have no idea what that key should be. So, basically, I'm asking, is there a way I can instead connect through WPA? I've tried creating a new connection in network manager, but that won't work, it keeps falling back to the WEP connection and asking me for a key. I have tried to install the XP driver using ndiswrapper but I don't know if that's working or not. Is there a way to tell if: A) the card is working as it should B) the correct drivers are installed (again, I installed the XP one using ndiswrapper NET8180.INF, but I'm not sure what to do next) Any help would be appreciated. Thank you.

  Read the article

• setting up vpn server

  - by Lock

  I need help in visualising how to setup our VPN box when we move to our new network with Telstra. We have a safe@office 500P, which has a public IP and a private IP of 192.168.19.2. It is physically connected to our router, which has 4 different interfaces, one being 192.168.19.1. On the VPN box, we have a static route to forward everything to 192.168.19.1 which is the router, and from there it works out where to go. Now, we are moving to a Telstra WAN and things are setup a little differently. Our head office router has only 3 interfaces- 1 is for the link to the switch that has the fibre connection (so our route to the internet and other branches), 1 is for our 10.10.20.x network and one is for the local branch network. I really have no idea how to set this up as with the new setup, we will not have a port for it to plug into on the router. Could I just plug it into the 10.10.20.x network? Would I have to give it a public IP or can we just forward through the ports that it would use? Another suggestion was to VLAN our switch into two networks- one for the 10.10.20.x network and one for the network the VPN currently sits on (192.168.19.x), and setup the router to trunk between the port and the switch. Not sure how to do this. Sorry VPN's are definitely not my strong suit. Any advice appreciated!

  Read the article

• Rendering a WPF Network Map/Graph layout - Manual? PathListBox? Something Else?

  - by Ben Von Handorf

  I'm writing code to present the user with a simplified network map. At any given time, the map is focused on a specific item... say a router or a server. Based on the focused item, other network entities are grouped into sets (i.e. subnets or domains) and then rendered around the focused item. Lines would represent connections and groups would be visually grouped inside a rectangle or ellipse. Panning and zooming are required features. An item can be selected to display more information in a "properties" style window. An item could also be double-clicked to re-focus the entire network map on that item. At that point, the entire map would be re-calculated. I am using MVVM without any framework, as of yet. Assume the logic for grouping items and determining what should be shown or not is all in place. I'm looking for the best way to approach the UI layout. So far, I'm aware of the following options: Use a canvas for layout (inside a ScrollViewer to handle the panning). Have my ViewModel make use of a Layout Manager type of class, which would handle assigning all the layout properties (Top, Left, etc.). Bind my set of display items to an ItemsControl and use Data Templates to handle the actual rendering. The drawbacks with this approach: Highly manual layout on my part. Lots of calculation. I have to handle item selection manually. Computation of connecting lines is manual. The Pros of this approach: I can draw additional lines between child subnets as appropriate (manually). Additional LayoutManagers could be added later to render the display differently. This could probably be wrapped up into some sort of a GraphLayout control to be re-used. Present the focused item at the center of the display and then use a PathListBox for layout of the additional items. Have my ViewModel expose a simple list of things to be drawn and bind them to the PathListBox. Override the ListBoxItem Template to also create a line geometry from the borders of the focused item (tricky) to the bound item. Use DataTemplates to handle the case where the item being bound is a subnet, in which case we would use another PathListBox in the template to display items inside the subnet. The drawbacks with this approach: Selected Item synchronization across multiple `PathListBox`es. Only one item on the whole graph can be selected at a time, but each child PathListBox maintains its own selection. Also, subnets cannot be selected, but would be selectable without additional work. Drawing the connecting lines is going to be a bit of trickery in the ListBoxItem template, since I need to know the correct side of the focused item to connect to. The pros of this approach: I get to stay out of the layout business, more. I'm looking for any advice or thoughts from others who have encountered similar issues or who have more WPF experience than I. I'm using WPF 4, so any new tricks are legal and encouraged.

  Read the article

• SCVMM 2012 R2 - Installing Virtual Switch Fails with Error 2916

  - by Brian M.

  So I've been attempting to teach myself SCVMM 2012 and Hyper-V Server 2012 R2, and I seem to have hit a snag. I've connected my Hyper-V Host to SCVMM 2012 successfully, and created a logical network, logical switch, and uplink port profile (which I essentially blew through with the default settings). However when I attempt to create a virtual switch on my Hyper-V host, I run into an issue. The job will use my logical network settings I created to configure the virtual switch, but when it tries to apply it to the host, it stalls and eventually fails with the following error: Error (2916) VMM is unable to complete the request. The connection to the agent vmhost1.test.loc was lost. WinRM: URL: [h**p://vmhost1.test.loc:5985], Verb: [GET], Resource: [h**p://schemas.microsoft.com/wbem/wsman/1/wmi/root/virtualization/v2/Msvm_ConcreteJob?InstanceID=2F401A71-14A2-4636-9B3E-10C0EE942D33] Unknown error (0x80338126) Recommended Action Ensure that the Windows Remote Management (WinRM) service and the VMM agent are installed and running and that a firewall is not blocking HTTP/HTTPS traffic. Ensure that VMM server is able to communicate with econ-hyperv2.econ.loc over WinRM by successfully running the following command: winrm id –r:vmhost1.test.loc This problem can also be caused by a Windows Management Instrumentation (WMI) service crash. If the server is running Windows Server 2008 R2, ensure that KB 982293 (h**p://support.microsoft.com/kb/982293) is installed on it. If the error persists, restart vmhost1.test.loc and then try the operation again. Refer to h**p://support.microsoft.com/kb/2742275 for more details. I restarted the server, and upon booting am greeted with a message stating "No active network adapters found." I load up powershell and run "Get-NetAdapter -IncludeHidden" to see what's going on, and get the following: Name InterfaceDescription ifIndex Status ---- -------------------- ------- ----- Local Area Connection* 5 WAN Miniport (PPPOE) 6 Di... Ethernet Microsoft Hyper-V Network Switch Def... 10 Local Area Connection* 1 WAN Miniport (L2TP) 2 Di... Local Area Connection* 8 WAN Miniport (Network Monitor) 9 Up Local Area Connection* 4 WAN Miniport (PPTP) 5 Di... Ethernet 2 Broadcom NetXtreme Gigabit Ethernet 13 Up Local Area Connection* 7 WAN Miniport (IPv6) 8 Up Local Area Connection* 9 Microsoft Kernel Debug Network Adapter 11 No... Local Area Connection* 3 WAN Miniport (IKEv2) 4 Di... Local Area Connection* 2 WAN Miniport (SSTP) 3 Di... vSwitch (TEST Test Swi... Hyper-V Virtual Switch Extension Ada... 17 Up Local Area Connection* 6 WAN Miniport (IP) 7 Up Now the machine is no longer visible on the network, and I don't have the slightest idea what went wrong, and more importantly how to undo the damage I caused in order to get back to where I was (save for re-installing Hyper-V Server, but I really would rather know what's going on and how to fix it)! Does anybody have any ideas? Much appreciated!

  Read the article

• How to start networking on a wired interface before logon in Ubuntu Desktop Edition

  - by Burly

  Problem Ubuntu 9.10 Desktop Edition (and possibly previous versions as well, I haven't tested them) has no network connections after boot until at least 1 user logs in. This means any services that require networking (e.g. openssh-server) are not available until someone logs in locally either via gdm, kdm, or a TTY. Background Ubuntu 9.10 Desktop Edition uses the NetworkManager service to take commands from the nm-applet in Gnome (or it's equivalent in KDE). As I understand it, while NetworkManager is running at boot, it is not issued any commands to connect until you login for the first time because nm-applet isn't running until you login and your Gnome session starts (or similar for KDE). I'm not sure what prompts NetworkManager to connect to the network when you login via a TTY. There are several relevant variables involved in starting up the network connections including: Wired vs Wireless (and the resulting drivers, SSID, passwords, and priorities) Static vs DHCP Multiple interfaces Constraints Support Ubuntu 9.10 Karmic Koala (bonus points for additional supported versions) Support wired eth0 interface Receive an IP address via DHCP Receive DNS information via DHCP (obviously the DHCP server must provide this information) Enable networking at the proper time (e.g. some time after file systems are loaded but before network services like ssh start) Switching distros or versions (e.g. to Server Edition) is not an acceptable solution Switching to a Static IP configuration is not an acceptable solution Question How to start networking on a wired interface before logon in Ubuntu Desktop Edition? What I have tried Per this guide, adding the following entry into /etc/network/interfaces so that NetworkManager won't manage the eth0 interface: auth eth0 iface inet dhcp After reboot eth0 is down. Issuing ifconfig eth0 up brings the interface up but it receives no IP address. Issuing dhclient eth0 instead Does bring up the interface and it Does receive an IP address. Completely removing the NetworkManager package in addition to the settings above. I'm a bit confused with the whole UpStart/SysVinit mangling that's going in Ubuntu currently (I'm more familiar with the CentOS world). However, directly issuing sudo /etc/init.d/networking start Or sudo start networking does not bring up the eth0 interface at all, much less get an IP address. See-Also How to force NetworkManager to make a connection before login? References Ubuntu Desktop Edition Ubuntu Networking Configuration Using Command Line Automatic Network Configuration Via Command-Line Start network connection before login

  Read the article

• eth0:0 is configured but not listed in ifconfig output

  - by FractalizeR

  Hello. I have the following problem: My server was given two IPs from [b]different[/b] subnets. Now I am trying to configure the system to work properly. I have created [root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 # Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) HWADDR=00:30:48:DA:B1:0E DEVICE=eth0 BOOTPROTO=none BROADCAST=79.174.69.255 IPADDR=79.174.69.241 NETMASK=255.255.254.0 NETWORK=79.174.68.0 ONBOOT=yes GATEWAY=79.174.68.1 TYPE=Ethernet [root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0:0 # Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) HWADDR=00:30:48:DA:B1:0E DEVICE=eth0 BOOTPROTO=none BROADCAST=79.174.69.255 IPADDR=79.174.71.74 NETMASK=255.255.255.0 NETWORK=79.174.71.1 ONBOOT=yes GATEWAY=79.174.71.1 TYPE=Ethernet But both after "service network restart" and after "reboot" [root@server ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:30:48:DA:B1:0E inet addr:79.174.71.74 Bcast:79.174.71.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:feda:b10e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:910284 errors:0 dropped:0 overruns:0 frame:0 TX packets:2924 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:257964879 (246.0 MiB) TX bytes:232450 (227.0 KiB) Memory:df220000-df240000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:27 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6976 (6.8 KiB) TX bytes:6976 (6.8 KiB) Device eth0:0 is not shown as active. If I try [root@server ~]# ifconfig eth0:0 eth0:0 Link encap:Ethernet HWaddr 00:30:48:DA:B1:0E UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:df220000-df240000 It is shown as up and running, but IP is not assigned to it. Also it is strange, that IP address assigned to eth0:0 in config file is used by eth0. /var/log/messages shows nothing about network configuration errors on either eth0 or eth0:0. system-config-network seem to understand all settings correctly and resaves them ok also. "ifup eth0:0" executes ok, but ifconfig afterwards shows no eth0:0 device after that. What did I do wrong? May be the problem is that IPs are from different subnets?

  Read the article

• How to connect SAN from CentOS through two iSCSI Targets

  - by garconcn

  I had asked the similar question before. This time I want to use subnet for two iSCSI Targets, hence I start a new question. I have an old Promise VTrak M500i SAN Server. It comes with 2 iSCSI ports. I want to connect to two LUNs on the SAN server through two separate Targets from CentOS 5.7 64bits server. My network setup is as follows: CentOS server: Management network - 192.168.1.1 Storage network 1 - 192.168.5.2 Storage network 2 - 192.168.6.2 Promise SAN server: Management network - 192.168.1.2 iSCSI Port 1 - 192.168.5.1 iSCSI Port 2 - 192.168.6.1 I have two Logical Drives on this SAN and they are mapped as follows: Index Initiator Name LUN Mapping 0 iqn.2011-11:backup (LD0,0) 1 iqn.2011-11:template (LD1,1) Basically, I want the traffic to iqn.2011-11:backup LUN 0 through 192.168.5.1 network the traffic to iqn.2011-11:template LUN 1 through 192.168.6.1 network I don't use MPIO, just want to separate the traffic to avoid traffic jam. How do I achieve this? I am new to SAN stuff, please explain as much detail as you can. Thank you. The following are what I am doing now. After mapping the LUN to my pre-defined Initiators, the CentOS server can discover both Targets. [root@centos ~]# iscsiadm -m discovery -t sendtargets -p 192.168.5.1 192.168.5.1:3260,1 iscsi-1 192.168.6.1:3260,2 iscsi-1 [root@centos ~]# iscsiadm -m discovery -t sendtargets -p 192.168.6.1 192.168.6.1:3260,2 iscsi-1 192.168.5.1:3260,1 iscsi-1 [root@centos ~]# /etc/init.d/iscsi start iscsid is stopped Starting iSCSI daemon: [ OK ] [ OK ] Setting up iSCSI targets: Logging in to [iface: default, target: iscsi-1, portal: 192.168.6.1,3260] Logging in to [iface: default, target: iscsi-1, portal: 192.168.5.1,3260] Login to [iface: default, target: iscsi-1, portal: 192.168.6.1,3260] successful. Login to [iface: default, target: iscsi-1, portal: 192.168.5.1,3260] successful. [ OK ] [root@centos ~]# iscsiadm -m session tcp: [1] 192.168.6.1:3260,2 iscsi-1 tcp: [2] 192.168.5.1:3260,1 iscsi-1 When I check the LUN mapping on the SAN server for the two Logical Drives, both LUNs are connected through Port0-192.168.5.2 with the Initiator defined in CentOS. Assigned Initiator List: Initiator Name Alias IP Address LUN iqn.2011-11.centos centos.mydomain.com Port0-192.168.5.2 0 Initiator Name Alias IP Address LUN iqn.2011-11.centos centos.mydomain.com Port1-192.168.5.2 1 I assume the following is what I want: Initiator Name Alias IP Address LUN iqn.2011-11.backup centos.mydomain.com Port0-192.168.5.2 0 Initiator Name Alias IP Address LUN iqn.2011-11.template centos.mydomain.com Port0-192.168.6.2 1

  Read the article

• Ubuntu Natty: 32-bit userland, 64-bit kernel?

  - by dsimcha

  I'm trying to manually install a 64-bit kernel for 32-bit Ubuntu. I have my reasons for doing so, but they're too complicated to explain here. Prior to Natty, this worked fine. Now, on Natty, I get the following error message when I try doing it the same way: dsimcha@dsimcha-laptop:~$ sudo dpkg -i --force-architecture linux-image-2.6.38-8-server_2.6.38-8.42_amd64.deb [sudo] password for dsimcha: dpkg: error processing linux-image-2.6.38-8-server_2.6.38-8.42_amd64.deb (--install): cannot access archive: No such file or directory Errors were encountered while processing: linux-image-2.6.38-8-server_2.6.38-8.42_amd64.deb dsimcha@dsimcha-laptop:~$ cd Downloads/ dsimcha@dsimcha-laptop:~/Downloads$ sudo dpkg -i --force-architecture linux-image-2.6.38-8-server_2.6.38-8.42_amd64.deb dpkg: warning: overriding problem because --force enabled: package architecture (amd64) does not match system (i386) (Reading database ... 159153 files and directories currently installed.) Preparing to replace linux-image-2.6.38-8-server:amd64 2.6.38-8.42 (using linux-image-2.6.38-8-server_2.6.38-8.42_amd64.deb) ... Done. Unpacking replacement linux-image-2.6.38-8-server:amd64 ... Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 2.6.38-8-server /boot/vmlinuz-2.6.38-8-server run-parts: executing /etc/kernel/postrm.d/zz-update-grub 2.6.38-8-server /boot/vmlinuz-2.6.38-8-server dpkg: dependency problems prevent configuration of linux-image-2.6.38-8-server:amd64: linux-image-2.6.38-8-server:amd64 depends on initramfs-tools (>= 0.36ubuntu6). linux-image-2.6.38-8-server:amd64 depends on coreutils | fileutils (>= 4.0); however: Package coreutils:amd64 is not installed. linux-image-2.6.38-8-server:amd64 depends on module-init-tools (>= 3.3-pre11-4ubuntu3); however: linux-image-2.6.38-8-server:amd64 depends on wireless-crda; however: dpkg: error processing linux-image-2.6.38-8-server:amd64 (--install): dependency problems - leaving unconfigured Errors were encountered while processing: linux-image-2.6.38-8-server:amd64 When I try the dependencies manually, I get, for example: dsimcha@dsimcha-laptop:~/Downloads$ sudo dpkg -i --force-architecture coreutils_8.5-1ubuntu6_amd64.deb dpkg: warning: overriding problem because --force enabled: package architecture (amd64) does not match system (i386) dpkg: error processing coreutils_8.5-1ubuntu6_amd64.deb (--install): coreutils:amd64 8.5-1ubuntu6 (Multi-Arch: no) is not co-installable with coreutils:i386 8.5-1ubuntu6 (Multi-Arch: no) which is currently installed Errors were encountered while processing: coreutils_8.5-1ubuntu6_amd64.deb Has anyone had any success installing 64-bit kernels on 32-bit Natty? If so, how can this be done?

  Read the article

• Macintosh computers cannot connect to router unless we re-start the modem and router

  - by dwwilson66

  We have a small office network with DSL and a Netgear WNR-2000 wireless router acting as a DHCP server. There are nine devices connected to the router, wirelessly and wired. Whenever a Mac computer tries to connect, it's unsuccessful until we restart the router. Each of the possible devices that can connect to the network is listed in a table to assign certain IP addresses to certain MAC addresses. I am running WPA-PSK security. I can view the router status and see that the Mac's MAC address is visible to the router, but with a 169.* IP address, even though I'm assigning its MAC address to an IP address within my subnet. All non-Mac devices attached to the network connect properly, and can access the network properly even AFTER the Mac has not successfully connected. The network includes Windows devices, Roku boxes, printers and internet ready TVs. This to me, would point to a DHCP issue with how Mac communicates with my network. One interesting thing to note is that if a Mac connects and is prevented from sleeping, it will stay connected indefinitely; reissuing the security cert from the router works fine. I'm not sure if that's supposed to sever & re-establish a connection with the updated credentials or not, but I do stay connected. If the Mac sleeps and is awakened while the security cert is still valid, it connects fine. If the security certificate expires while the Mac is asleep, we need to restart the router. Restarting the router will ALWAYS assigns the proper IP addresses to the Mac equipment. I have heard anecdotally that Mac doesn't play well with 802.11n; I have not tested any other Wireless protocols. There's a couple issues here: First, I found this on Stack, Mac laptop crashing wireless router, but it's not rally applicable since the router isn't crashing. But, it does give some clues about Mac's accessing the network. I did change my encryption from WEP to WPA-PSK, but after about a week, we're still experiencing the issue. I'm not really sure if there's anything else useful in that question. Second, I'm considering getting a 802.11c router and hooking it up to the wireless N router. the 802.11c router would handle all the Mac traffic, and would be set up as a Mac-only subnet. Everything else would remain as is. However, I'm not sure if this is doable on a technology level...do I need a bridge or is this some way to do this with regular consumer gear?

  Read the article

• Ubuntu hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  I'm posting this on SU after it stalled on askubuntu. I hope someone here can help! If you'd prefer to answer on AU itself, here's the link: http://askubuntu.com/questions/365177/hardware-wireless-switch-has-no-effect-after-suspend-and-13-10-upgrade Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Edit. This morning, I had had the laptop suspended all night, and then when I tried to awake it, it simply wouldn't. It would try, and then it would sleep again (I guess it felt a little bit like me! </badjoke>). Is it possible these problems are related? Edit. I don't have enough reputation on SU proper to post links to pastebins and other questions I've tried, so I'm putting them in comments, and of course they're available in the original question.

  Read the article

• Routing between 2 different subnets on 2 different interfaces in SonicOS

  - by Chris1499

  I'm having a bit of a problem allowing traffic between two of my subnets. Here's the structure I've built. The X0 interface has our windows server on it and it handles DHCP/DNS, etc. X1 has the WAN connection. The Sonicwall is handling DHCP on X2. The X3 interface is connected to a different vlan on the 48 port switch. The Sonicwall is handling DHCP on this network as well. So here's what i want to do. The network on X2 is for our guest wireless; i don't want it to be able to access any of the other networks, just the internet, so i that all blocked in the firewall. No issues there. The X3 network is going to be for programmable controllers, and needs to be able to access the X0 network where our computers are. This is where my problem is. I'm not able to get between the 192.168.2.xxx and the 192.168.1.xxx on interfaces X0 and X3 respectively. I have these rules set up in the firewall. The Lan Primary Subnet is the 192.168.2.0 on X0. So if i'm not mistaken, this will allow traffic between the two through the firewall. Now this is where I'm a little confused. Do i need to use NAT to get the traffic from X0 to go to X3 (and vice versa), or a static route, or both? Currently i have both, though i doubt they're done correctly (also in screenshot). I've tried to ping between the two without luck. Any advice, or if you see what's wrong with my setup, is much appreciated. If you need some more information, let me know. Thanks all! EDIT: So i found that i don't neither either NAT or a static route, that the setting in the firewall is enough. I can now ping from the 192.168.1.xxx network, however i can't access the server on the 192.168.2.xxx network. When i try to access i get "An error occured while reconnecting to Z: to server Microsoft Windows Network: The local device name is already in use. This connection has not been restored. What am i missing?

  Read the article

• Enterprise IPv6 Migration - End of proxypac ? Start of Point-to-Point ? +10K users

  - by Yohann

  Let's start with a diagram : We can see a "typical" IPv4 company network with : An Internet acces through a proxy An "Others companys" access through an dedicated proxy A direct access to local resources All computers have a proxy.pac file that indicates which proxy to use or whether to connect directly. Computers have access to just a local DNS (no name resolution for google.com for example.) By the way ... The company does not respect the RFC1918 internally and uses public addresses! (historical reason). The use of internet proxy explicitly makes it possible to not to have problem. What if we would migrate to IPv6? Step 1 : IPv6 internet access Internet access in IPv6 is easy. Indeed, just connect the proxy in Internet IPv4 and IPv6. There is nothing to do in internal network : Step 2 : IPv6 AND IPv4 in internal network And why not full IPv6 network directly? Because there is always the old servers that are not compatible IPv6 .. Option 1 : Same architecture as in IPv4 with a proxy pac This is probably the easiest solution. But is this the best? I think the transition to IPv6 is an opportunity not to bother with this proxy pac! Option 2 : New architecture with transparent proxy, whithout proxypac, recursive DNS Oh yes! In this new architecture, we have: Explicit Internet Proxy becomes a Transparent Internet Proxy Local DNS becomes a Normal Recursive DNS + authorative for local domains No proxypac Explicit Company Proxy becomes a Transparent Company Proxy Routing Internal Routers reditect IP of appx.ext.example.com to Company Proxy. The default gateway is the Transparent Internet proxy. Questions What do you think of this architecture IPv6? This architecture will reveal the IP addresses of our internal network but it is protected by firewalls. Is this a real big problem? Should we keep the explicit use of a proxy? -How would you make for this migration scenario? -And you, how do you do in your company? Thanks! Feel free to edit my post to make it better.

  Read the article

• sonyEricsson C905 VPN connection

  - by Snigger

  Hi I have a SonyEricsson C905 phone. I want to connect to a Wifi network and use it's internet . I can connect to network using my phone but the network provides a VPN service to use internet so I need to connect to that VPN network too to be able use internet. Can I connect to VPN via my C905 ? If yes How? Thanks

  Read the article

• Resources such as libraries, engines and frameworks to make Javacript-based MMORTS? [closed]

  - by hhh

  I am looking for resources outlined to make a MMORTS with Javascript as the client-side, probably just a simple canvas for the frontend. The guy in the video here mentions that JavaScript is one of the most misunderstood language -- and I do believe that. I think one can make quite cool games with it in the future. So I am now proactively looking for resources and perhaps some ideas. My first idea contained Node.js, C and NetBSD/bozohttpd (or the-4-7-chars' *ix-thing with green-logo -thing, move the q here) but I acknowledge my beginner -style approach -- this issue is broad and not only for one person to make it all-the-time-improved project! So I think perfect for community to tinker. Some games and examples possibly easy to make into MMORTS BrowserQuest here under MPL 2.0 and its content licensed under CC-BY-SA 3.0 (source here) [proprietary] LoU here and built with JS/Qooxdoo/c#/Windows-Server/ISS/etc, source. MY ANSWER BEGINS HERE TO BE MOVED BELOW, REQUIRING RE-OPENING. PLEASE, VOTE TO OPEN IT -- HELP US TO TINKER! My answer Generic Is there an MMO-related research body? Although about Android, certain things also appropriate with JS -game: Are there any 2D gaming libraries/frameworks/engines for Android? Why is it so hard to develop a MMO? Browser based MMO Architecture MMO architecture - Highly Scalable with Reporting capabilities What are the Elements of an MMO Game? Is this the right architecture for our MMORPG mobile game? Looking for architectures to develop massive multiplayer game server Information on seamless MMO server architecture Game-mechanics (search) Question sounding like about LoU: What are the different ways to balance an online multiplayer game where user spend different amounts of time online? Building an instance system What are the different ways to balance an online multiplayer game where user spend different amounts of time online? Hosting is it possible to make a MMO starting with scalable hosting? Should I keep login server apart from game server? MMO techniques, algorithms and resources for keeping bandwidth low? MMO Proxy Server Javascript and Client-based things What do I need to do a MMORTS in JavaScript with small amount of Developers? How to update the monsters in my MMO server using Node.js and Socket.IO Are there any good html 5 mmo design tutorials? Networking Loadbalancing Questions Something about TCP, routers, NAT, etc: How do I start writing an MMO game server? Who does the AI calculations in an MMO? They need someone more knowledgable to work with, a lot of cases where the same words mean different things. Data Structures What data structure should I use for a Diablo/WoW-style talent tree? Game Engine Need an engine for MMO mockup Helper sites http://www.gamedev.net/page/index.html

  Read the article

• Comment étendre vos rapports de trackers Codendi en moins de 10 minutes ?, par Nicolas Terray

  Nicolas Terray (Codendi) vous présente un nouveau tutoriel intitulé: Comment étendre vos rapports de trackers en moins de 10 minutes ? ou plus génériquement " Comment exploiter l'architecture ouverte des trackers Codendi ? " Citation: Dans ce tutoriel je vais vous montrer comment exploiter la fonctionnalité d'extension de Codendi avec le nouveau système de tracker de la v 4.2 et son architecture en plugin. Cet article va êtr...

  Read the article

• The Netherland's Telco Market Leader Discusses the Value of Oracle's AIA to IT Managers

  Ernst Lamein, Manager IT Architecture CRM at KPN and David Krauss, Product Marketing Director at Oracle speak with Cliff about Oracle's Application Integration Architecture (AIA) and how it can help IT Managers address integration requirements while simplifying and consolidating their IT infrastructure.

  Read the article

• April 2010 Chicago Architects Group Meeting

  - by Tim Murphy

  The Chicago Architects Group will be holding its next meeting on April 20th.  Please come and join us and get involved in our architect community. Register Presenter: Matt Hidinger Topic: Onion Architecture      Location: Illinois Technology Association 200 S. Wacker Dr., Suite 1500 Room A/B Chicago, IL 60606 Time: 5:30 - Doors open at 5:00 del.icio.us Tags: Chicago Architects Group,Data Integration Architecture,Mike Vogt

  Read the article

• links for 2010-03-24

  - by Bob Rhubart

  @dhinchcliffe: When online communities go to work "As we see a growing set of examples of successful online communities in the enterprise space (both internally and externally), the broad outlines are emerging of what is turning into a vital new channel for innovation, business agility, customer relationships, and productive output for most organizations: Online communities as one of the most potent new ways to achieve business objectives, both in terms of cost and quality." -- Dion Hinchcliffe (tags: enterprisearchitecture entarch enterprise2.0 socialmedia) Steven Chan: WebCenter 11g (11.1.1.2) Certified with E-Business Suite Release 12 Steven Chan shares information on WebCenter 11g's (11.1.1.2) certification with Oracle E-Business Suite Release 12, along with a list of certified EBS 12 Platforms (tags: oracle otn enterprise2.0 webcenter ebs) @oraclenerd: 1Z0-052 - Exploring the Oracle Database Architecture Oracle ACE Chet "Oraclenerd" Justice shares a list of resources/documentation covering Oracle Database Architecture. (tags: oracle otn oracleace dba certification architecture) @oraclenerd: 1Z0-052 - Books "I don't believe I have ever purchased a book on or about Oracle. The documentation provided, especially for the database, is top notch. There is so much information available out there if you just know how to find it. Reading AskTom for years didn't hurt either." -- Chet "@oraclenerd" Justice. (tags: otn oracle oracleace certification dba) Lucas Jellema: Castle in the clouds – Building the Connexys SaaS application with Fusion Middleware Oracle ACE Director Lucas Jellema shares the slides from the presentation he and colleague Arne van der Ing submitted for OBUG 2010. (tags: otn oracle oracleace cloud saas obug fusionmiddleware connexys) John Burke: Why Your ERP System Isn't Ready for the Next Evolution of the Enterprise "[ERP] has to become a stealthy modern app to help you quickly adapt to business changes while managing vital information. And through modern middleware it will connect to everything. So yes ERP as we've know it is dead, but long live ERP as a connected application member of the modern enterprise." -- John Burke, Group VP, Applications Business Unit, Oracle (tags: oracle otn entarch erp) Darwin-IT: Postfix for handling mail in your integration solution "It took me some time to understand Postfix. I was quite overwhelmed by the options. And it took me some time to figure out how to configure it for this particular usecase...But as with most other things..it turns out to be simple." -- Martien van den Akker (tags: oracle linux soa postfix) TheServerSide.com: Cameron Purdy at TSSJS 2010: If Java beats C++, what's next? ''It turns out that Java performance is much better on modern architecture. That is because of multicore processors and in-lining.'' -- Cameron Purdy, as quoted in an article by Jack Vaughn (tags: oracle java otn c++)

  Read the article

< Previous Page | 279 280 281 282 283 284 285 286 287 288 289 290  | Next Page >