Search Results

Search found 31973 results on 1279 pages for 'network library'.

Page 283/1279 | < Previous Page | 279 280 281 282 283 284 285 286 287 288 289 290  | Next Page >

  • How to get the speed of a network card on the command line?

    - by nelaar
    I am trying to see what the speed of some network cards on a remote server. Our reporting software says they are 10Mbps, but I am sure that is wrong they should be 1Gbps. Our monitoring software uses SNMP to query the servers, perhaps the servers are reporting information incorrectly. ifconfig does not report what the speed of the devices are. How can I see what the currently configured speed of the cards are.

    Read the article

  • Toshiba Satellite Laptop Realtek Network Driver Error code (10)?

    - by Silent
    hello all i have a Toshiba 64 bit windows vista, i tried looking for the drivers from the main website but no luck all the ones i got did not work or did not do anything. would someone know where i can find it or maybe fix this issue it will not find any network wireless or even if i hook up the Ethernet cable. i don't know why Toshiba makes it hard they should have a complete bundle. Model: A305-S687

    Read the article

  • What is the correct network configuration for a devStack VM (virtualbox)?

    - by Olivier
    Usually when I setup a new Ubuntu VM, i keep the eth0 in NAT mode to get the internet & I add a eth1 interface in HostOnly mode so that I can ssh. But using this devStack guide : Running a Cloud in a VM, it looks like it tried to use eth0 as the public interface (install got stuck because eth0 lost the network). I know an OpenStack setup usually requires two NICs, so I'm wondering what is the correct configuration for my VM.

    Read the article

  • Why should I use a switched network over routed?

    - by SRobertJames
    Now that routers are affordable, why should I build a network using Layer 2 switches, which degenerate to broadcasting under poor conditions, and not just use real routing at Layer 3? Edit: Got some great replies. Let me clarify the question: Of course, at the lowest level, you want to plug your end nodes into a switch, not a router (as demonstrated by AlReece). I'm referring to switches which are used to bridge traffic between segments - that is, switches connected to other switches.

    Read the article

  • What logs should I collect from a Windows server network?

    - by Cygnus X
    I'm setting up a log collection server for my Windows network (about 30 servers ranging from 2003 to 2008 R2, and about 300 vista/7 clients), and I was wondering which logs are good to collect and which ones are a waste of time. I'm going to collect the obvious ones (system, security, event, firewall, and role specific logs) but are there any others I should be worried about? I'm using Splunk if that helps answer the question.

    Read the article

  • How to output a simple network activity plot in console in Linux?

    - by Vi.
    There's tload that plots load average. There's iftop that network usage as bars. How to do something like this: # tcpdump -i eth0 --plot 'host 1.2.3.4' 13:45:03 | | 0 in 0 out 13:45:04 |O | 0 in 1MB out 13:45:05 |OOOI | 500 KB in 4MB out 13:45:06 |OIIII | 6MB in 1MB out 13:45:07 | | 0 in 0 out 13:45:08 |IIIIIIIIIIII | 53M in 0 out

    Read the article

  • Limiting network throughput of an already launched process ? (Linux/FreeBSD)

    - by jbdenis
    Hello everybody, is there any utility to limit the network throughput of a process after it has been launched ? Simple example: you note that a user takes all your upload bandwidth using scp and you'd like to limit the rate or decrease the priority of the transfer. I guess i could use a combination of iptables/tc or pf to achieve that, but i was wondering if there is a "one-shot" tool available (like tickle with a --pid option ^^) ? Regards, Jean-Baptiste

    Read the article

  • Atheros Wireless card shows up as two different models?

    - by geermc4
    Hi I've been fighting these wireless drivers for a few days and just recently i noticed that the model the Wireless controller appears in lspci is different sometimes. This is the data i have after installing Ubuntu Server 64 bit ~# lspci -k .... 04:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: AzureWave Device 1d89 Kernel driver in use: ath9k Kernel modules: ath9k ran some updates, restarted, all was good, all though it did say that linux-headers-server linux-image-server linux-server where beeing kept back. After that i installed ubuntu-desktop (aptitude install ubuntu-desktop --without-recommends) restarted and not only is the wireless not working anymore, but the hardware is listed as a different card ~# lspci -k .... 04:00.0 Ethernet controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) has no available drivers for it, still i tried to modprobe ath9k, they show up in lsmod as loaded, but still iw list shows nothing. this is what it looked like before the ubuntu-desktop instalation Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (14.0 dBm) * 2417 MHz [2] (15.0 dBm) * 2422 MHz [3] (15.0 dBm) * 2427 MHz [4] (15.0 dBm) * 2432 MHz [5] (15.0 dBm) * 2437 MHz [6] (15.0 dBm) * 2442 MHz [7] (15.0 dBm) * 2447 MHz [8] (15.0 dBm) * 2452 MHz [9] (15.0 dBm) * 2457 MHz [10] (15.0 dBm) * 2462 MHz [11] (15.0 dBm) * 2467 MHz [12] (15.0 dBm) (passive scanning) * 2472 MHz [13] (14.0 dBm) (passive scanning) * 2484 MHz [14] (17.0 dBm) (passive scanning) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor interface combinations are not supported Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS. What's with the hardware change? If it has 2, how can i make the AR9285 always load and disable AR5008, or, is it the same and it's just showing it different? :| Oh and I've tried this on Ubuntu 10.04 server, xubuntu 12.04, ubuntu 12.04 desktop and server. Thanks in advanced. -- Here's some more info, i have it setup in 2 hard drives, 1 works and the other one i'm using to figure it out The one that works... # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.147 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 74:2f:68:4a:26:73 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-18-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:fea00000-fea0ffff Here's where it doesn't # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.160 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network UNCLAIMED description: Ethernet controller product: AR5008 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:fea00000-fea0ffff Update I've noticed that if i blacklist the ath9k and ath9k_common modules lspci gives me the AR9285, but then I need to modprobe ath9k for it to work, does this make any sense? If so, why?

    Read the article

  • WDS 2008 R2 DHCP Error

    - by scampbell
    Im having a problem where I get the error 'An error occurred while obtaining an IP address from the DHCP server. Please check to ensure that there is an operational DHCP server on this network segment' when booting from a standard WDS boot.wim image taken from a Windows 7 DVD. I am using Server 2008 R2 and am adding the drivers to the boot using WDS, but also have the problem if the drivers are injected beforehand using DISM. When the error occurs I can shift + F10 and IPCONFIG and see it HAS picked up an internal IP from DHCP. Seems maybe it is timing out before it gets the IP? DHCP server is not on the WDS box but is in the same subnet. As per some fixes I have read I enabled RSTP on my switches but that didnt help. I have included the end of setupact.log to see if any of you have any ideas. Seems to be failing but as I say, the network IS initialized as I can see the internal IP assigned by DHCP when running IPCONFIG. I dont suppose theres any way of increasing the timeout? Thanks. 2011-04-11 17:26:31, Info [0x0b0022] WDS StartNetworking: Trying to start networking. 2011-04-11 17:26:31, Info WDS Network service dhcp not running or could not be queried: 264d00 1 1 2011-04-11 17:26:31, Info WDS Network service lmhosts not running or could not be queried: 264e18 1 1 2011-04-11 17:26:31, Info WDS Network service lanmanworkstation not running or could not be queried: 264d00 1 1 2011-04-11 17:26:31, Info WDS Network service bfe not running or could not be queried: 264e18 1 1 2011-04-11 17:26:31, Info WDS Network service ikeext not running or could not be queried: 264d00 1 1 2011-04-11 17:26:31, Info WDS Network service mpssvc not running or could not be queried: 264e18 1 1 2011-04-11 17:27:24, Info WDS Installing device pci\ven_14e4&dev_1691&subsys_04aa1028 X:\WINDOWS\INF\oem37.inf succeeded 2011-04-11 17:27:25, Info WDS No computer name specified, generating a random name. 2011-04-11 17:27:25, Info WDS Renaming computer to MININT-VN2P876. 2011-04-11 17:27:25, Info WDS Acquired profiling mutex 2011-04-11 17:27:25, Info WDS Service winmgmt disable: 0x00000000 2011-04-11 17:27:25, Info WDS Service winmgmt stop: 0x00000000 2011-04-11 17:27:25, Info WDS Service winmgmt enable: 0x00000000 2011-04-11 17:27:25, Info WDS Released profiling mutex 2011-04-11 17:27:25, Info WDS Acquired profiling mutex 2011-04-11 17:27:25, Info WDS Install MS_MSCLIENT: 0x0004a020 2011-04-11 17:27:25, Info WDS Install MS_NETBIOS: 0x0004a020 2011-04-11 17:27:25, Info WDS Install MS_SMB: 0x0004a020 2011-04-11 17:27:25, Info WDS Install MS_TCPIP6: 0x0004a020 2011-04-11 17:27:26, Info WDS Install MS_TCPIP: 0x0004a020 2011-04-11 17:27:26, Info WDS Service dhcp start: 0x00000000 2011-04-11 17:27:26, Info WDS Service lmhosts start: 0x00000000 2011-04-11 17:27:26, Info WDS Service ikeext start: 0x00000000 2011-04-11 17:27:26, Info WDS Service mpssvc start: 0x00000000 2011-04-11 17:27:26, Info WDS Released profiling mutex 2011-04-11 17:27:26, Info WDS Spent 967ms installing network components 2011-04-11 17:27:28, Info WDS Spent 2247ms installing network drivers 2011-04-11 17:27:38, Info WDS QueryAdapterStatus: no operational adapters found. 2011-04-11 17:27:38, Info WDS Spent 10140ms confirming network initialization; status 0x80004005 2011-04-11 17:27:38, Info WDS WaitForNetworkToInitialize failed; ignoring error 2011-04-11 17:27:38, Info WDS GetNetworkingInfo: WpeNetworkStatus returned [0x0]. Flags set: 2011-04-11 17:27:38, Error [0x0b003f] WDS StartNetworking: Failed to start networking. Error code [0x800704C6].[gle=0x000000cb] 2011-04-11 17:27:38, Info [0x0640ae] IBSLIB PublishMessage: Publishing message [WdsClient: An error occurred while obtaining an IP address from the DHCP server. Please check to ensure that there is an operational DHCP server on this network segment.]

    Read the article

  • Cisco ASA: How to route PPPoE-assigned subnet?

    - by Martijn Heemels
    We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

    Read the article

  • Is there a library or other way to do 128-bit math operations?

    - by samoz
    I am writing a cryptography application and need to work with 128 bit numbers. In addition to standard add, subtract, multiply, divide, and comparisons, I also need a power and modulo function as well. Does anyone know of a library or other implementation that can do this? If not 128-bit, is there a 64-bit option available?

    Read the article

  • Is there a C# library that will perform the Excel NORMINV function?

    - by Portman
    I'm running some Monte Carlo simulations and making extensive use of the Excel function NORM.INV using Office Interrop. This functions takes three arguments (probability, average, standard deviation) and returns the inverse of the cumulative distribution. I'd like to move my code into a web app, but that will require installing Excel on the server. Does anybody know of a C# statistics library that has an equivalent function to NORM.INV?

    Read the article

  • Which OAuth library do you find works best for Objective-C/iPhone?

    - by Brennan
    I have been looking to switch to OAuth for my Twitter integration code and now that there is a deadline in less than 7 weeks (see countdown link) it is even more important to make the jump to OAuth. I have been doing Basic Authentication which is extremely easy. Unfortunately OAuth does not appear to be something that I would whip together in a couple of hours. http://www.countdowntooauth.com/ So I am looking to use a library. I have put together the following list. MPOAuth MGTwitterEngine OAuthConsumer I see that MPOAuth has some great features with a good deal of testing code in place but there is one big problem. It does not work. The sample iPhone project that is supposed to authenticate with Twitter causes an error which others have identified and logged as a bug. http://code.google.com/p/mpoauthconnection/issues/detail?id=29 The last code change was March 11 and this bug was filed on March 30. It has been over a month and this critical bug has not been fixed yet. So I have moved on to MGTwitterEngine. I pulled down the source code and loaded it up in Xcode. Immediately I find that there are a few dependencies and the README file does not have a clear list of steps to fetch those dependencies and integrate them with the project so that it builds successfully. I see this as a sign that the project is not mature enough for prime time. I see also that the project references 2 libraries for JSON when one should be enough. One is TouchJSON which has worked well for me so I am again discouraged from relying on this project for my applications. I did find that MGTwitterEngine makes use of OAuthConsumer which is one of many OAuth projects hosted by an OAuth project on Google Code. http://code.google.com/p/oauth/ http://code.google.com/p/oauthconsumer/wiki/UsingOAuthConsumer It looks like OAuthConsumer is a good choice at first glance. It is hosted with other OAuth libraries and has some nice documentation with it. I pulled down the code and it builds without errors but it does have many warnings. And when I run the new Build and Analyze feature in Xcode 3.2 I see 50 analyzer results. Many are marked as potential memory leaks which would likely lead to instability in any app which uses this library. It seems there is no clear winner and I have to go with something before the big Twitter OAuth deadline. Any suggestions?

    Read the article

  • How would I skew an image with GD Library?

    - by Jason
    I want to skew an image into a trapezoidal shape. The left and right edges need to be straight up and down; the top and left edges need to be angular. I have no idea what the best way to do this is. I'm using GD Library and PHP. Can anyone point me in the right direction? Thanks, Jason

    Read the article

  • What's the best library to do a URL hash/history in JQuery?

    - by alex
    I've been looking around JQuery libraries for the URL hash, but found none that were good. There is the "history plugin", but we all know it's buggy and isn't flexible. I am loading my pages inside a div. I'll need a way to do back/forward along with the url hashing. mydomain.com/#home mydomain.com/#aboutus mydomain.com/#register What's the best library that can handle all of this?

    Read the article

< Previous Page | 279 280 281 282 283 284 285 286 287 288 289 290  | Next Page >