Search Results

Search found 23082 results on 924 pages for 'address space'.

Page 284/924 | < Previous Page | 280 281 282 283 284 285 286 287 288 289 290 291  | Next Page >

• Application Crash cleared the content of the Folder

  - by Ameya

  Recently while working on the LinuxDC++ over the network the application crashed while downloading files. Now my Downloads folder which had at least 60-80GB of data is completely cleaned but the system is not reporting the available the correct free space. Is there way to restore the contents of the folder only as the solution available are for the whole partition. I just want to recover the contents from one folder.

  Read the article

• Cisco Aironet 1200 Series AP Configuration

  - by nonterrorist

  I am attempting to configure a new CISCO Aironet 1200 Series Access Point to have a fixed IP. I have been searching online and I have come to the conclusion that the default IP address of this device is 10.0.0.1. These are the steps I have taken: My machine is plugged directly into the Ethernet port (not the Console port) of the AP. My Ethernet adapter is set to 10.0.0.2. I have reset the AP by holding the Mode button while powering up the device. The issue remains that I can not access 10.0.0.1 through the web, nor can I ping that address.

  Read the article

• Why would one bother marking up properly and semantically?

  - by Madara Uchiha

  Note that I (try) to mark up as semantically as possible because I like they way it looks and feels, but not because I'm aware of any other stunning advantages. The point of my question is to be able to educate others Well, I've seen a lot of articles and tutorials which often state "Let's mark this up in the most semantic possible way". But a strange thought came to me, why? Why would one need (or want) to bother with the specific elements which convey the correct semantic meaning? Specifically, I'm referring to the new HTML5 elements, such as <time>, <output>, or <address>. Especially, if the page "works" (it renders nicely in all browsers). Why would I want to use elements like <time> or <address>, where nothing at all (or at the worst case, a generic <span>) works just as nicely? I'm asking this because I'm seeing a multitude of (very popular) websites (this one included) which does not follow these so-called best practices.

  Read the article

• Boost Your SEO With Good Keyword Research

  Once you get into the search engine optimization game, you'll learn all types of basic principles. Emphasizing your keyword in code is one. Stressing Your Keyword For SEO. Keywords are the key, pun supposed, to search engine optimization. You must develop an understanding of what your projections are wanting for in your space of business. Keyword research is the method for doing this and a step that should be conducted with nice precision and effort.

  Read the article

• Cron Jobs unable to deliver email error report

  - by root

  I am sure I have right syntax and I am still unable to receive report emails to my email address. My OS is CentOS 6.4. My Crontab script is MAILTO="[email protected]" * * * * * /usr/bin/php5 /home/myusername/public_html/cron.php /post/find_submit_test/1/ Email address [email protected] is working fine and I tested sendmail from ssh which is too working fine but cron reports are unable to be delivered. I checked WHM for notification settings couldn't even find anything relevant there. Please advice me how to fix this. Thanks

  Read the article

• sizes of RAM, of virtual memory and of swap for 32-bit OS

  - by Tim

  If I understand correctly, a 32-bit OS (Ubuntu) can only address 4GiB memory, so RAM with size larger than 4Gib will only be used 4Gib of itself and the rest is a waste. I am now confused about this situation for RAM with similar one for virtual memory and for swap. with virtual memory being swap + RAM, if the size of the virtual memory exceeds 4Gib, will the exceeding part be a waste for the 32-bit OS? if I now have to choose the size for my swap partition, is it a factor to consider that the 32-bit OS can only address 4GiB memory? Does the size of swap have to be chosen with respect to the 4Gib addressible limitation? Will the swap exceeding 4GiB always be a waste? is virtual memory equal to RAM and swap? or can virtual memory use space on the hard drive outside the swap partition? Thanks and regards!

  Read the article

• Unable to copy and paste (or cut and paste) photos already reduced in size from Word document into a

  - by Simon Child

  Hello I cannot copy photos and paste them from a word document into the text of an email on my Sony Laptop having already substantially redcued the size of the photos using Microsoft Office Picture Manager. I can readily manage to perform this functjon from my work place PC but am presently working mostly from home. I am trying to email photos and text using a btinternet.com email address but have checked that I cannot perform the task using my alternate googlemail email address either. I can obviously highlight the relevant photographs but whenever I try to copy or cut them into the email text the paste function is disabled. Assistance would be much appreciated. Kind regards Simon

  Read the article

• Sorting IPv4 Addresses

  - by Kumba

  So I've run into a quandary on sorting IPv4 addresses, and didn't know if there was a set rule in some obscure networking document. Do I do a straight sort on the raw address only (such as converting the IP address to a 32bit number and then sorting), do I factor in the CIDR via some mathematical formula, do I sort via the CIDR only (as if I'm comparing the network size and not the addresses directly)? I.e., normal math, we'd do something like -1 < 0 < 1 to denote the order of precedence. Given say, 10.1.0.0/16, 172.16.0.0/12, 192.168.1.0/24, and 192.168.1.42, what would be the order of precedence?

  Read the article

• Resolving host names to their domain name in an internal BIND domain

  - by Adam Plumb

  I'm setting up a domain on my home network for learning purposes, using BIND on CentOS to act as the name server. I've got the name server up and running as type master for my internal domain (plumbnicoll.family), and can do forward and reverse lookups from other computers in my LAN. For example, host office2.plumbnicoll.family correctly returns office2.plumbnicoll.family has address 192.168.1.3. What I'd like is to be able to resolve just office2 to its address, without needing to put .plumbnicoll.family at the end. Is this possible, or even desirable to do? I'm running a mixed environment at home with both Linux and Windows computers.

  Read the article

• IIS 7.5 and ASP.NET MVC Routing

  - by m__

  I'm running an ASP.NET MVC 3 application on an IIS 7.5 server (my development server). When I set up my production server something goes wrong. Serving the same application binaries, using the same web.config file and connecting to the same database I get different results. Something must be wrong with my IIS configuration, but what? Here's an example I visit http://mysite.com/An/AspNetMvc/Routed/Address/1 and everything works I visit http://mysite.com/An/AspNetMvc/Routed/Address/1.1 works on my development server but not on my production server which gives the following error HTTP Error 404.0 - Not Found The resource you are looking for has been removed, had its name changed, or is temporarily unavailable. Module IIS Web Core Notification MapRequestHandler Handler StaticFile Error Code 0x80070002 Somehow the URL is served as a static file on my production server which led me to investigate my IIS Handler Mappings, but without luck.

  Read the article

• Apache Virtual Host Configuration

  - by Carl

  I have been searching the internet for an hour now, and I was hoping for a quick hint here so that I could solve my problem a wee bit faster. My virtual server is so far only accessible through an IP address, no DNS entry yet, and so far none needed either. The problem I have is with Apache2, the virtual hosts are puzzling me. What I need is: Access to my project (based on Symfony2) from the outside with the IP address Access to my project from localhost What I have got: Access from the outside results in rendering the websites in /var/www/vhosts/htdocs/default, while from the inside results in rendering the websites in /var/www. Why the difference? What is a recommended configuration for my use case?

  Read the article

• Network configuration problem

  - by Musti

  in my dorm I have to change network configuration and then if it is successfull, I have to enter a user name and password for wired internet connection. Anyway, I had many attempts but I couldnt achieve, and please look at my steps and tell me if there is something wrong and at the end there is an error, but I really dont have any idea about this error. (I am a new ubuntu user, and network is far away of my interests) 1) /etc/network/interfaces auto eth0 iface eth0 inet static address 172.030.014.038 netmask 255.255.255.252 network 192.168.2.0 broadcast 192.168.2.255 gateway 172.030.014.038 2) sudo gedit /etc/resolv.conf nameserver 010.050.001.001 nameserver 010.050.001.002 3) /etc/init.d/networking stop Deconfiguring network interfaces... [ OK ] 4) /etc/init.d/networking restart Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces Reconfiguring network interfaces... 172.030.014.038: Unknown host ifconfig: `--help' gives usage information. Failed to bring up eth0 Note: IP-address, netmask, gateway, Preferred DNS server and Alternate DNS server ara given by the management of Dorm. It wad very easy in windows but I couldnt achieve in Ubuntu. I also tried to edit from "edit connections" but the save button is gray and I cannot save it. Thanks in advance. / Musti

  Read the article

• Unable to access the server via SSH

  - by Rishee

  when I am trying to access the server through ssh it says: ssh: connect to host xx.yyy.zzz.x port 22: Connection refused and on the server in auth.log it shows following log entry: Address xx.yyy.zzz.x maps to xx.yyy.zzz.x.static-pune-vsnl.net.in, but this does not map back to the address - POSSIBLE BREAK-IN ATTEMPT! I have created a user account for that user and it is also in enabled status. Requested info It is Ubuntu 11.10 It is configured as SSH Server using openssh-server I am trying to connect to this server using Putty from Windows 7 i.e. My Desktop I have also asked this on AskUbuntu: http://askubuntu.com/questions/118556/unable-to-access-the-server-via-ssh

  Read the article

• ISP issue browsing "sonos.com" - need to diagnose and prove [closed]

  - by john

  I am unable to browse to a website "sonos.com" with my ISP (virgin). I have ruled out browsers, PCs, macs, routers, wifi, etc. Other ISPs (even other virgin connections in different areas!) supply this site no problem. I am 99% convinced there is a DNS issue lurking here. There is something fishy about the DNS for the site : What I notice is that online DNS sites tell me the right IP address for "sonos.com", but not for "www.sonos.com". Anyway when I type "sonos.com" the browser (any/all of the 4 I tried) fail to display the page. Firefox gives a "connection was reset" error. If I browse to sonos.com using the IP address it works OK. Browsing to www.sonos.com or sonos.com works fine with other ISPs of course. Questions: 1 Does anyone have any idea what might be going on here? 2 Any suggestions as to tools/monitors to help investigate/prove what is going on I can then take this up with virgin and/or sonos. Thanks

  Read the article

• Memory management (segmentation and paging) in 80286 and 80386: How does it work?

  - by Andrew J. Brehm

  I found lots of Web sites and books explaining how memory management worked on the 8086 and later x86 CPUs in Real Mode. I understand, I think, how two 16 bit values, segment address and offset are combined to get a linear 20 bit physical address (shift segment four bits to the left, add offset; segments are 64K and start every 16 bytes). But I couldn't find any good Web sites or books that explained how memory management works in Protected Mode, specifically the differences between 80286 and 80386. Can anyone point me to a good Web site or book (or explain it right here)? (For extra credit, i.e. an upvote, how does it work in Long Mode?)

  Read the article

• Simple dig output?

  - by knocte

  In a script I want to be able to write an IP address to somewhere easily, so I thought using dig (or a similar command) with back-ticks. However the simplest output I've been able to come up to wrt dig parameters is > dig -t A +noall +answer www.google.com www.google.com. 300 IN A 173.194.66.106 www.google.com. 300 IN A 173.194.66.104 Any way (extra arg, different tool instead of dig?) to get rid of the junk apart from the IP address?? (And please don't tell me to use sed.) Thanks

  Read the article

• Windows doesn't get access to internet though linux easily does

  - by flashnik

  We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

  Read the article

• Windows Server 2008 R2 Firewall - Interface specific rules

  - by Mehmet Ergut

  I'm trying to define per interface rules, much like it was in Server 2003. We will be replacing our old 2003 server with a new 2008 R2 server. The server runs IIS and SQL Server. It's a dedicated server at the hosting company. We use a OpenVPN connection from the office to access SQL server, RDesktop, FTP and other administrative services. Only http and ssh is listening on the public interface. On the old server running 2003, I was able to define global rules for http and ssh, and allow other services only on the vpn interface. I can't find a way to do the same on 2008 R2. I understand that there is the Network Location Awareness service, firewall rules are applied according to the current network location. But I don't understand the purpose of this on a server. The only close solution I found is to set the scope on the firewall rule and restrict remote ip addresses to the private subnet of the office. But the ports will still be listening on the public interface. So how can I restrict a firewall rule to the connections coming from the vpn interface ? A note on this page states that scoping a rule to an interface does not exist anymore: In earlier versions of Windows, many of these command accepted a parameter called interface. This parameter is not supported in the firewall context in Windows Vista or later versions of Windows. I can't believe that they simply decided to remove a core firewall functionality that every firewall has. There must be a way to restrict a rule to an interface. Any ideas ? I'm still unable to find an adequate solution to my problem. So for now, my workaround is this: Administrative services listen on VPN IP address Firewall rules restrict the scope to the local IP address of VPN Public services listen on all interfaces, no scope restriction on firewall rules This is not optimal, if I change the IP address of the VPN, I need to edit the firewall rules too. It won't be the case if the rules were bound to the interface.

  Read the article

• How can I copy data from a windows disk to another partition?

  - by TardisGuy

  I have a new Solid State Drive, and it's very fast (but tiny, 128GB). But it seems to be much faster in Linux. Now, am I correct in assuming that if I Gparted copy paste the {_Boot MSreserved__][_________NTFS__________] in to (1st Empty space, same partition) and it will be bootable, right? Will this work? I also heard I should turn off 'journaling' for the SSD filesystem. Is that needed for this as well?

  Read the article

• Cross-match a number of worksheets to one master worksheet

  - by Carter

  Hopefully the title is not too confusing. Basically, I have a master list of addresses and those addresses are listed in multiple columns (Column A - street number, Column B - street name, Column C - street type etc) and I get a another set of addresses on a daily basis with the same address formatting. What I need to do is cross-match the daily changing list of addresses to the first list to remove any matching entries. So, for example, if the first list has 123 Main St on it, I have to ensure that there are no entries of 123 Main St on any subsequent daily lists. I'm using one address as an example but the lists contain upwards of 10000 addresses that have to be cross matched. I don't need them flagged or highlighted, just deleted from the daily lists (though if they have to be flagged or highlighted, I could work with that) Any help here would be much appreciated.

  Read the article

• SSH connection falling down

  - by kappa

  I've set up a connection with autossh that creates some tunnels at system startup, but if I try to connect, after successful login (with RSA key) connection fall down, here a trace: debug1: Authentication succeeded (publickey). debug1: Remote connections from LOCALHOST:5006 forwarded to local address localhost:22 debug1: Remote connections from LOCALHOST:6006 forwarded to local address localhost:80 debug1: channel 0: new [client-session] debug1: Requesting [email protected] debug1: Entering interactive session. debug1: remote forward success for: listen 5006, connect localhost:22 debug1: remote forward success for: listen 6006, connect localhost:80 debug1: All remote forwarding requests processed debug1: Sending environment. debug1: Sending env LANG = it_IT.UTF-8 debug1: Sending env LC_CTYPE = en_US.UTF-8 debug1: client_input_channel_req: channel 0 rtype exit-status reply 0 debug1: client_input_channel_req: channel 0 rtype [email protected] reply 0 debug1: channel 0: free: client-session, nchannels 1 Transferred: sent 2400, received 2312 bytes, in 1.3 seconds Bytes per second: sent 1904.2, received 1834.4 debug1: Exit status 1 What can be the problem? All this stuff is managed by a script already running on another machine (creating reverse tunnels on the same machine but with different ports)

  Read the article

• How to solve virtual host issue

  - by Webnet

  I have multiple sites all setup the same as below except "bk" has something else in it's place... NameVirtualHost *:80 <VirtualHost bk:80> ServerName bk DocumentRoot /var/www/bk.com/ </VirtualHost> and I get these errors when restarting apache: [Mon Jan 17 10:28:56 2011] [error] VirtualHost bk:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results [Mon Jan 17 10:28:56 2011] [warn] NameVirtualHost bk:80 has no VirtualHosts I don't get it... the other 2 sites I have virtual host configurations for this exact same way don't throw any errors update One error message fixed - here's where I'm at now.. <VirtualHost bk:80> ServerName bk DocumentRoot /var/www/bk.com/ </VirtualHost> [Mon Jan 17 10:28:56 2011] [error] VirtualHost bk:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results

  Read the article

• Port Forwarding for Remote Desktop

  - by Vaibhav Bajpai

  I have two Mac notebooks at home, I have assigned them static private IPs. I have also set my router to a DynDNS address, which updates everytime my router gets a new public IP. I have enabled Screen Sharing on both notebooks. I can successfully goto my router webpage using the DynDNS address. I understand I need to port-forward to get Screen Sharing to work from outside. Lets assume, notebooks have private IP 192.168.1.2 and 192.168.1.3 I am kind of lost here, would appreciate some help (I need to be able remote desktop to both notebooks)

  Read the article

• OS X server VPN local ip

  - by gbrandt

  Hi all, I have 10.6.2 server on the internet. I want to vpn into it to get access. I start VPN and it gives me an address in the range I have set 192.168.2.100-192.168.2.105. However the server itself does not have a local ip of 192.168.2.x so I cannot ping it or ssh into it or anything. The machine VPNing gets an ifconfig entry that looks like this: ppp0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1280 inet 192.168.2.100 --> 70.72.xxx.xxx netmask 0xffffff00 Where I think it should get: ppp0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1280 inet 192.168.2.100 --> 192.168.2.1 netmask 0xffffff00 I can't find anywhere to set the local vpn IP address. And I can't find a pptpd.conf file either. Any help is appreciated.

  Read the article

• The Growing Utility of Article Submission Services

  Businesses today are striving for their individual space and identity in the face of mounting competition. Many business persons are now open to creative and innovative means in order to make their mark in the corporate world.

  Read the article

< Previous Page | 280 281 282 283 284 285 286 287 288 289 290 291  | Next Page >