Search Results

Search found 13104 results on 525 pages for 'malcolm box'.

Page 286/525 | < Previous Page | 282 283 284 285 286 287 288 289 290 291 292 293  | Next Page >

• wireshark not seeing all packets on WiFi

  - by Caffeine Coma

  I'm using Wireshark on OSX, trying to sniff my home network over WiFi. While I can see packets that are sent to/from the host I'm sniffing on, I'm not seeing anything else that goes over the WiFi. It's like I'm not in promiscuous mode or something (the promiscuous mode box is in fact checked). The router is an Apple Airport Extreme, protected by WPA2. I'm attached to the network I'm trying to sniff, so I'm confused about why I can't see other traffic. Edit: I solved this by the following: Plug Macbook directly into the Airport Extreme router Enable "internet sharing" on Macbook, with no password. Bind wireless device (the one I wanted to sniff) to the WiFi hotspot generated by Internet sharing in step 2. Run Wireshark on the Macbook, bound to device en1. Don't forget to disable sharing after you're done. :-)

  Read the article

• Sharepoint site settings add on ssl port number?

  - by Mike

  WSS 3.0 IIS6/WinSever2003 CAG We have several WSS sites on a SharePoint WSS box that talk to the outside, all of which are SSL enabled. So you get a CAG(Citrix Access Gateway) to translate the 443 port to the local ssl port on the server. Everything is set up and works fine until you get into the Site Settings and start rooting around, it seems like a very unstable link library. Links will try to use the local ssl port number instead of the 443 standard; it will try to skip the step. Is that the site? Any ideas on how to fix it?

  Read the article

• Windows 8.1 installation: Which drive is the F drive?

  - by sammyg

  I am doing a clean install of Windows 8.1 on an old PC. It was purchased as download from Microsoft Store and written to and booted from a USB flash drive. It went through all of these steps: Copying Windows Files Getting files ready for installation Installing features Installing updates Then at "Getting finished" I am stuck at this stupid dialog box. Please unplug the following external drive and click OK to restart your computer and finish installing Windows. F: How do I tell what physical drive this is? Can I drop to command prompt during installation? And is it safe to unplug it while powered on? There is no external hard drive connected, none that I can see. There is no USB or FireWire drive connected externally. I think it sees one of the internal drives as external... in some weird way?!

  Read the article

• Monitor sleep in Windows XP does not work. Is there an add on to force it?

  - by bert

  I have an EEE box with XP Home and a DVI connected TFT, and it does not sleep the monitor. It only starts working after I go to the energy control panel and turn it off and on again. Then the timed sleep works for the current session of computer use. After a shut down and boot next day, sleep does not work again (it is still set in the preferences however). What can hold the sleep function from working? Are there issues with Skype or MSN? Is there a utility to be less critic to processes interrupting sleep and offer a more reliable monitor sleep function for XP?

  Read the article

• Question about Linux Device Drivers.

  - by smwikipedia

  I have just installed the Xubuntu. My box runs quite slower than before when installed with a Win7. I am wondering if I am missing some device drivers. I can use gnome-device-manager to list my devices. In the device list view, I saw several blue question mark on the left side of devices. Based on my windows experience, the question mark should indicate the device is not properly configured. Is it the same with gnome-device-manager? And most importantly, how could I know for sure whether or not the corresponding device drivers have been installed? Many thanks.

  Read the article

• Microsoft Outlook: show multi-day appointments as boxes in calendar day and week view

  - by Bernd

  I would like to show appointments spanning several days the same way as appintments within a single day. Single day appointments are shown with a white or colored box, covering the day horizontally. Multi-day appointments are shown in the day/week header and are indicated blue or purple on the left side of a day. This happens even if a multi-day appointment is not an all-day appointment (i.e. checkbox is off) and I have a start and end time. I frequently have a hard time seeing appointment overlaps wenn acceping single day appointments. Therefore I am looking for multi-day appointments shown the same way as single day appointments. I am on Outlook 2003.

  Read the article

• Outlook - Out Of Office can't set

  - by derjur

  Exchange 2007, Outlook 2010 Error when setting Out Of Office (Automatic Replies) from Outlook: Your automatic reply settings cannot be displayed because the server is currently unavailable. Try again later. Setting this through OWA works fine. Autodiscover is working, and all addresses are resolvable through DNS. Outlook profile created from scratch. Anonymous access disabled for EWS/OWA (IIS on Exchange box). I'm out of steam for troubleshooting. Any ideas?

  Read the article

• Multiple Instances of aspnet_wp.exe?

  - by Mike Keller

  Is this normal? I was poking around Google and from what I found it should be, but we have 60 of them going, and only two .NET apps running on this particular server. All of them are at 0% CPU and at about 3meg of memory usage. We can't really restart the server right now to see if that clears them out, we store a lot of data on it that people need regularly. Any clues for investigating this issue would be appreciated. This particular box is an oldie Windows2000 and .NET 2.0 Thanks.

  Read the article

• openvpn and virtualbox

  - by hyperboreean

  Hi guys, I have a linux machine on which I occasionally run Windows XP in Virtual Box. All runs wonderful, except for the openvpn in XP, which can't connect to the vpn server running on a remote machine. The vpn client works from linux ... as far as I read until now it seems to be a problem of port forwarding ... I keep getting this error: TCP/UDP: Incoming packet rejected from 10.0.2.2:1194, expected peer address: (allow this incoming source address/port by removing --remote or adding --float) , but have no idea how to fix it.

  Read the article

• AMD Radeon 7900 series: setting up 3 monitors

  - by Nilzone-

  I have an AMD Radeon 7900 series, which should support up to 6 screens. I'm having problems getting my third one working. Im running windows 8, and have installed all the latest AMD drivers. My screens are: Samusng syncmaster S27D391HS Samusng syncmaster S24B350H Samusng syncmaster S24B350H The first 24" monitor I use HDMI to DVI cable. The second 24" I use VGA to DVI cable. Lastly, for the 27" I use HDMI cable. The result is, no matter what I do, I never get more than two screens on simultaneously. I have also tried getting a DisplayPort to HDMI cable to use for the 27", but Im not sure if it was passive or active (didn't say on the box, nor did I ask). So my question is: is an active displayport to HDMI the solution, or is there someting else Im overlooking? (I have read similar posts on this subject, but I use a slightly different combo of cables. That is why I made a post of my own as well)

  Read the article

• On Mikrotik RouterOS, is it possible to get Netflow information from a bridged connection?

  - by Tim

  I have a RouterOS box set up to bridge two ethernet connections. I have use-ip-firewall=yes in the bridge configuration, so that the ports go through the firewall. I've enabled netflow reporting via ip/traffic-flow, but the only packets I see reported are broadcast and multicast packets, not the packets that are flowing through the bridge. The documentation indicates that traffic flow logging happens after firewall processing and that it won't work with bridged connections by default, but I would have thought that use-ip-firewall=yes ought to address this. Is it possible to make this work somehow?

  Read the article

• Point example.com to webserver in DNS record

  - by ggstevens

  I have a Mac Mini Server (named Server) with the following DNS setup Primary Zone: example.com mysql-host.example.com machine (10.0.0.101) server.example.com machine (10.0.0.100) server.example.com nameserver (10.0.0.100) www.example.com machine (10.0.0.102) www.example.com is a linux box with Apache. How do I get both example.com and www.example.com to work. Right now, I can view my website with www.example.com only. I know there's nothing that points example.com to the IP, but when I create a machine record without a hostname I get an error (This machine record cannot be created without a host name.).

  Read the article

• Excel: Conditional Formatting (Highlighting) Values Based on Another Worksheet

  - by ScottSEA

  I have a workbook that has two worksheets. The first worksheet is simply a list of the first 78,498 prime numbers in a single column, A1-A78498. The second worksheet has a grid of numbers from 1 to n. The goal is to highlight the cells with prime numbers in the grid by referencing the prime number values in the other worksheet. Is this possible, and if so, how? edit I have named the column with my prime numbers "PRIMES1T". I would like the formula to work for the entire worksheet, regardless of size, but my excel-fu is extremely weak. If at all possible, I would like to be able to enter the formula in the dialog box for conditional formatting (as below): I have tried =NOT(ISNA(MATCH(A:Z,PRIMES1T,0) (only A-Z, but have to start somewhere) with no luck.

  Read the article

• Remote Desktop over SSH SOCKS proxy to bypass firewall

  - by scrumpyjack

  Hi folks, I'm trying to connect to a Windows server from my Mac using RDC2.1 for Mac. The problem is the server I need to connect to is guarded by the evil dragon - IP-based access control on a completely separate network. I have an IP I can get in on, but it's at my office (i.e. a completely separate network). Because that network isn't set up for VPN, I've set up a SOCKS proxy through an SSH tunnel (which is all working fine). (SSH proxy) Me (on my Mac) ----------> Office Linux box ----> Windows server (home network) (office network) (other network) From my Linux server in my office (the SSH server) I can telnet to port 3389 on the Windows server, no problem. But from my Mac I can't get so much as a squeak out of it. Any ideas?

  Read the article

• routing traffic between two network cards through firewall

  - by RubyFreak

  I'm trying to test a network device (firewall) using a Linux box, with two network cards, one interface connected to the WAN zone and another interface to LAN zone. The configuration is similar with that |ETH0| <-> | FW | <-> ETH1 So from both interfaces I'm able to ping the respective firewall interface. But i'm not able to fire something like: ping -I eth0 ip.from.eth1 and to get any answer. Is that possible or should the linux network namespace solution or user level tcp stacks (VMs are out of question)

  Read the article

• Booting a Windows 7 installation on different hardware

  - by tomfanning

  I'm in a situation where I could do with very quickly migrating a Windows 7 (RTM x64) installation from one machine to another. What options are open to me in terms of getting W7 to boot after the drive is picked up and moved from one box to another? I thought it was supposed to be a little less sensitive to this kind of move than XP, but it doesn't work - it is stuck in a reboot loop and never reaches a GUI. Tried a few things so far, none of which have worked: Changed SATA mode in the BIOS of the target machine between ATA and AHCI run Windows 7 Startup Repair tried safe mode, no change (I will keep this list up to date as suggestions come in) UPDATE: I can confirm this reboot loop is due to STOP error 0x0000007B, and these codes follow: 0xFFFFF880009A98E8 0xFFFFFFFFC0000034 0x0000000000000000 0x0000000000000000 UPDATE: I didn't get anywhere on this and I ended up just rebuilding the machine. I think it should be theoretically possible, so I'm going to leave the question open in case someone comes along in future with an answer.

  Read the article

• how to? 1 domain name, 1 ISP Static IP, 1 router, 3 physical web Servers

  - by buliwyf

  I have 1 Static IP from my ISP, 58.59.60.61 I have 3 local physical web servers: Win2008 IIS 7, local IP 192.168.10.11, mydomain.com Ubuntu Apache2, local IP 192.168.10.12, subdomain1.mydomain.com Win2003 IIS 6, local IP 192.168.10.13, subdomain2.mydomain.com I have 1 domain name, mydomain.com. It is configured this way: Host(A), @, 58.59.60.61 Host(A), subdomain1, 58.59.60.61 Host(A), subdomain2, 58.59.60.61 My router is a pfSense box. It forwards all port 80 traffic to a group alias called "WebServers," which is my 3 web server IP's. This setup should work right? I believe I need to set the "host header names" in my web servers. In IIS I know how to do this. How do I do this in Apache2?

  Read the article

• ASUS EAH5770 CuCore problem: VLC Stutting!

  - by aiacet

  Hello to everyone and thank you in advance to all the people that will want help me. Like in the title my problem concernig this boring stutting when i play a Tv series episodes or a film on VLC whit my mew PC. Pc components are: AMD Phenom II X4 955 Black Box 125W Asus M4A785TD-M EVO Radeon HD5770 1GB GDDR5 Asus CoolerMaster GX 650W G.Skill 2x2GB PC3-12800 1600Mhz-787 4GBECO Western Digital 1TB SATAII 64MB Monitor are SyncMaster 920Nw OS: Windows XP 32 bit Display adapter drivers are updates at the latest release (catalyst 10.4) and also the ATi Vga bios are updated Besides when i play the same episode with DivX Plus Player i have video and audio stutting. I can play very well Dragon Age Origin and other games but i'm unable to see a beutyfull movie. Please help me

  Read the article

• Connect to wired and wireless networks at same time, Ubuntu

  - by Gary Chambers

  Currently, I have a media PC running Ubuntu 10.04 that I am trying to connect via a wired network cable directly to a NAS box, and wirelessly to the router. This works no problem after I run sudo /etc/init.d/networking restart but I can't get both interfaces to come up on system startup. My /etc/network/interfaces file reads as follows: auto eth0 iface eth0 inet static address 10.0.1.2 netmask 255.255.254.0 broadcast 10.0.1.255 network 10.0.1.0 auto wlan2 iface wlan2 inet dhcp As I say, I know this works, because I can get it to work by restarting the network interfaces, but I can't bring them both up on system startup. Does anyone know why this might be?

  Read the article

• How do I stop CRM from asking for admin credentials when printing report

  - by Ac0ua

  Problem: When printing a report in CRM, I am asked by the UAC for admin credentials. There is a long URL: https://(crm_hostname)/reserved.ReportViewerWebcontrol.axd?ReportSession=(ID)ControlID=(ID)Culture=1333&UICulture=1033&ReportStack=1&OpType=PrintCab Info: There are three users that have the issue laied out here. They are not admins of any kind. It looks like it is asking for permission to allow SQL Server Reporting Services 2008 to run. When I put my credentials in, it just brings up the Print dialog box (this is fine, just stop asking for credentials). I know this might sound silly but I downloaded and installed "SQL Server Reporting Services 2008" hopping my credentials would give permission right from the beginning. Giving the users local admin, I was told is not an option. Note: I did post this on community (dot) dynamics (dot) com but, they are not a very active website. Thanks for any help even if it just points me in the right direction!

  Read the article

• Can I do a "one-time" file content search in Windows Server 2008 without adding the folder to the index?

  - by G-.

  Can I search for files which contain a specific string in a folder if that folder is not in the search index? So, lets say folder 'textFiles' is not in the index. I navigate to this folder in windows explorer. I type '.ini' in the search box I want to see a result list containing only 'b.txt' FOLDER C:\textFiles\ FILE a.php CONTENT once twice thrice mice moose monkey FILE b.txt CONTENT mingle muddle middle.ini banana beer FILE c.spo CONTENT sellotape stapler phone book I do not have permission to add folders to the windows index and I do not have permission to install or run any executables that did not ship with the server or approved applications. I'd be happy with a windows native command line solution if necessary? Thanks G

  Read the article

• zeroconf (bonjour/avahi): macs do not see linuxes and vice versa

  - by codesnik

  In my home network I have several OS X boxes and several Ubuntu boxes. each Ubuntu box sees other boxes via zeroconf. I can "ssh ubuntu1.local" and "ping ubuntu1.local" from "ubuntu2.local", but both fail to lookup OSX boxes. and other way around, I can "ssh mini1.local" from "mbair.local". but it doesn't see "ubuntu1.local" why? do ubuntu and osx use different flavours of zeroconf? could be ubuntu, or osx tweaked to use common flavour?

  Read the article

• How to netboot ubuntu running iniside VirtualBox on Mac Air

  - by murungu

  Having configured a virtual machine for Ubuntu on VirtualBox on my mac air I need to install Ubuntu OS itself. I have selected the hardrive as the primary boot device and the network as the secondary boot device, so I am not prompted to install an Ubuntu disk at boot time. It attempts to netboot but is unable to locate Ubuntu and cannot find anywhere in the configuration where I can explicitly specify where to find and Ubuntu image, so assume it reverts to some default location and fails. Has anybody out there ever successfully installed ubuntu on virtual box on their Mac Air? What steos did you take to get it right?

  Read the article

• Why might powerpoint not let me adjust the height of a table row?

  - by YGA

  Powerpoint is fighting me every time I try to adjust the height of a table row, and I'm wondering if folks have ideas why that might be the case. See the attached picture; the Argentina row is of height 0.41", while the Nicaragua row is 0.61". Whenever I change to change the Nicaragua row (either by manually moving the row line, or by typing in a new height into the box) powerpoint immediately resets it. The difference? The Argentina row I typed in directly, while the Nicaragua row I pasted in from Excel. Thoughts what might be the difference?

  Read the article

• Best way to convert from IMAP to POP3?

  - by Brad

  At work, I connect to a corporate Exchange server via IMAP and Thunderbird 3. Over the course of a year or so, I've created quite a few folders on the server and have a lot of mail stored there. I'm hitting the storage limit of my mail account and want to convert to pulling mail down to my local box (running Linux) via POP3. I know that polling mail will only get mail in INBOX, but I'm wondering if there are solutions out there that could be used to pull mail from the other folders as well, or am I doomed to moving mail into the inbox manually and polling over and over again?

  Read the article

< Previous Page | 282 283 284 285 286 287 288 289 290 291 292 293  | Next Page >