Search Results

Search found 15487 results on 620 pages for 'android wireless'.

Page 288/620 | < Previous Page | 284 285 286 287 288 289 290 291 292 293 294 295  | Next Page >

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• Wlan connection got lost permanent

  - by chris

  I have a desktop with a fritz usb wlan n tick and tried ubuntu 12.04. installlation is fine and wlan is working, however connection drops permanent. reconnecting manually fixes it but after a few minutes it drops again. it's connected to a vodafone 802 box with wlan n fix set. it seems that it works when i switch off n mode...but i need to test. can someone confirm or is there another solution? i have another machine with 12.04 (hp 625 laptop) running where connection is stable. any help much appreciated. thank chris

  Read the article

• Connection manager detects network but won't connect

  - by Carson Chittom

  I've just installed 12.04 on my home desktop. Because of where it's located, in order not to have my children tripping over cat5 cable, I've got a cheap 802.11n USB device plugged in, which uses a Realtek 8192CU chip. The house wifi is protected with WPA2. Ubuntu's Network Manager detects the network, but connecting to it just times out and asks for the password again. I'm sure I'm using the correct password. No other computers on the house network are having any difficulty. This device previously worked correctly with both Windows 7 and OpenBSD in the same machine. The linux-firmware package is installed (from the disc) at version 1.79, and /lib/firmware/rtlwifi/rtl8192cufw.bin is present. dmesg|grep rtl only shows the "loading firmware" message. I've tried Google, but I apparently can't find the right set of words to plug in, because I haven't found anything related (lots of "doesn't work at all," but nothing matching my circumstances). Any help would be greatly appreciated.

  Read the article

• Problems connecting to eduroam wifi - ubuntu touch

  - by Fiona Cox

  I am trying to connect to our university's eduroam wi-fi network with my Nexus 4 running Ubuntu touch (utopic latest build), but can't get past the first stage. I wonder if anyone can help please? I am following these instructions (which worked for my iPhone): http://www.st-andrews.ac.uk/itsupport/mobile/eduroam/ But when I go to the bandit.st-andrews.ac.uk/connect page then follow the link to 'eduroam setup' I get the error message: Authorization Required This server could not verify that you are authorised to access the document requested. Either you supplied the wrong credentials (e.g., bad password), or your browser doesn't understand how to supply the credentials required. Apache/2.2.16 (Debian) Server at bandit.st-andrews.ac.uk Port 443 (Clearly it's the latter option (browser) as I haven't been asked for my credentials yet.) Is there a way round this, or am I just not going to be able to connect until further down the Ubuntu touch development road... Thanks!

  Read the article

• Ubuntu on Thinkpad Edge 11/13/14/15

  - by lasseespeholt

  I think a community wiki on problems (and solutions) when installing Ubuntu (10.10) on a Thinkpad Edge 11 would be nice (because I just got one ;)). I'll contribute with my own problems and solutions, and hope others will join too. Thinkwiki entry for the Edge 11 Known problems: No wifi-driver, solution: answer #1, answer #2 Fan is loud, even though it's on auto. No solution. Thinkfan is a possible solution, but correction values for sensors should be supplied (mapping sensors to specific areas). Also, one sensor is between -100C and +100C - maybe some kind of deactivation would help. FN keys stop working: see below. No sound on headphones: see below.

  Read the article

• Why does wifi hotspot doesn't work correctly?

  - by Habi

  I have created the wifi hotspot. In windows, it used to display wifi signal on my nokia C3 but after creating wifi hotspot from ubuntu, I am facing certain problem. Nokia C3 doesn't even gets wifi signal. But wifi signal appears in my samsung mobile GTS3-850 and I can access wifi if I put wifi security option to "none" On the other hand, if I create password then Nomatters, if I type right password or not, it doesn't connect to that wifi. Note : I use Wimax to access internet.

  Read the article

• USB Wifi that works with 12.04

  - by Colin Matheson

  I have done several hours of searching and I am still looking for a few USB wifi adaptors that run in 12.04 with no additional driver installations or other fiddling. I am looking to plug in the adaptor and have the laptop recognize and start connecting. We have 30 older laptops with flaky internal wifi cards so I thought that if I could find a $10-$20 USB adaptor that work reliably in 12.04 I could plug it in and solve all my connectivity problems for a few hundred dollars.

  Read the article

• Field Trip Automatically Alerts You to Local Places of Interest

  - by Jason Fitzpatrick

  Android: Field Trip is a free mobile app that acts like a local tour guide, alerting you to landmarks, historical sites, and unique local attractions. A simple walk around your city’s down town can turn into a history lesson or lead to the discovery of a new hang out. To use Field Trip simply install it on your GPS-enabled Android smartphone and start it up. You can configure the app to notify you of certain types of things (historic places, outdoor art, food and drink, and more), refine the results over time by telling the app which tidbits you enjoyed, and more. Field Trip even has a driving mode where you can turn it on and, as you drive through a city or across the countryside, it will narrate your journey by telling you about interesting sites you’re passing. Field Trip is free, Android only. Hit up the link below to take it for a spin. Field Trip [via Geek News Central] 8 Deadly Commands You Should Never Run on Linux 14 Special Google Searches That Show Instant Answers How To Create a Customized Windows 7 Installation Disc With Integrated Updates

  Read the article

• ACER Aspire V5-171 compatibility

  - by JamerTheProgrammer

  Im thinking about buying a V5-171 with an i3 in it. Im worried about secure boot though. I heard some people cant turn it off and it wont work... Im not shy to open it up and replace the hard drive with Ubuntu preinstalled. Im also worried about the wifi working. I have heard its been dropping out for people quite a bit along with also the trackpad not working. I dont mind replacing the wifi stick (if its even possible?) inside. Is the GPU (HD4000 i think) supported in ubuntu with full video accel? Thanks!

  Read the article

• Ubuntu 12.04 share the internet over WiFi from wvdial?

  - by Sour Lemon

  I have just installed Ubuntu 12.04 on a separate partition on my hard drive so I can dual boot to either Windows 7 or Ubuntu. I am living in Japan and so I'm using a mobile broadband USB device called "Softbank C02LC". By default it seems that this device isn't recognised so I did the following: Terminal: sudo su nano /usr/bin/usbModemScript Nano: #!/bin/bash echo 1c9e 9900 > /sys/bus/usb-serial/drivers/option1/new_id Terminal: chmod +x /usr/bin/usbModemScript nano /etc/udev/rules.d/option.rules Nano: ATTRS{idVendor}=="1c9e", ATTRS{idProduct}=="9900", RUN+="/usr/bin/usbModemScript" ATTRS{idVendor}=="1c9e", ATTRS{idProduct}=="9900", RUN+="/sbin/modprobe option" which made the device visible from the network manager etc. However even though I set up my details correctly when I created a new connection (Correct username, APN etc) as soon as I try to connect it almost immediately disconnects. Because of this I then followed the instructions at this site: http://debugitos.main.jp/index.php?Ubuntu%2F%A5%E2%A5%D0%A5%A4%A5%EB%A5%A4%A5%F3%A5%BF%A1%BC%A5%CD%A5%C3%A5%C8 And I ended up using the c02lc_connect script at the bottom of the page to connect to the internet. The file contains the following bash script: #!/bin/sh usbinterfece=/dev/ttyUSB2 VID=1c9e PID=9900 WRONG_PID=f000 LSUSB=/usr/sbin/lsusb GREP=/bin/grep MODPROBE=/sbin/modprobe SWITCH=/usr/sbin/usb_modeswitch SWITCH_D=/etc/usb_modeswitch.d WVDIAL=/usr/bin/wvdial SLEEP=/bin/sleep SUDO=/usr/bin/sudo WHICH=/usr/bin/which switch_config="$SWITCH_D/$VID:$WRONG_PID" if ! [ -x $WVDIAL -a -x $SWITCH ]; then echo "Install wvdial and usb_modeswitch." exit 0 fi check_usb() { local vid="$1" local pid="$2" ($LSUSB | $GREP "$vid:$pid") } if ! (check_usb "$VID" "$PID"); then echo "Cannot find modem device..." if (check_usb "$VID" "$WRONG_PID") && ( [ -f "$switch_config" ] ); then echo "The device is attached but its mode is wrong." echo "Try usb_modeswitch..." $SUDO $SWITCH -c "$switch_config" $SLEEP 1 if (check_usb "$VID" "$PID"); then echo "Successfully switched the mode." else echo "Failed to switch the mode..." exit 1 fi else exit 1 fi fi if [ ! -c "$usbinterface" ]; then $SUDO $MODPROBE usbserial vendor=0x$VID product=0x$PID $SLEEP 2 fi $SUDO $WVDIAL which works completely fine - no problems what-so-ever. But we also have 1 more laptop here which I need to share the internet connection with. In Windows 7 I do this with the Connectify program, and in Ubuntu I have seen that you can do things like set up hotspots etc. But because I am using WvDial I am not sure how I would share the internet. I am only beginning to use Ubuntu but unfortunately until I can figure out how to share the internet over WiFi when connected via WvDial I have to stick with Windows. If you have any ideas on how to do this it would be much appreciated!

  Read the article

• iwconfig usage for WEP access point?

  - by johan elmander

  I would like to use my wifi doggle in my pc (ubuntu 12.04). I am able to connect to my access point through the GUI. I would like to do the same in the terminal. My access point uses WEP. So I typed the following commands iwconfig wlan0 mode managed key 6d6f6e6579 iwconfig wlan0 essid "AccessPoint" dhclient wlan0 after typing dhclient wlan0 it waits like 1-2 min then outputs nothing and cannot connect to the Access Point. iwconfig output: wlan0 IEEE 802.11bgn ESSID:"AccessPoint" Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long timit:7 RTS thr=2347 B Fragment thr:off Encryption key:6D6F-6E65-79 Power Management:off I would appreciate any suggestion

  Read the article

• Ubuntu and Surface Pro, wifi issues not fixed?

  - by Confused or too stupid

  Just a quick question, from the numerous other threads I found, is the wifi still a no go straight out of installing Ubuntu? I tried this Dual boot Surface Pro with Ubuntu? with 13.04, the wifi is sporadic in working. From that and other threads I gathered that 13.10 would include the fix, so I tossed that onto the Surface as well, with the same results. Is there anything I am missing? Is there any other distro that has better luck with the Marvell chip?

  Read the article

• Internet connection randomly drops out

  - by Dr_Bunsen

  Since a week or 2, I have this random network failures. No error pops up, the system says it's still connected to the internet(wifi and wired). The problem is, I can't connect to anything, even a ping google.com gives no feedback. And after many network-manager resets it will work again, for just a minute, and drop out again. I noticed that the /etc/resolv.conf contains this line: nameserver 127.0.0.1 I left out the "Do not edit" stuff, and after it worked for a second, this line is added: search lan When I change the nameserver to 8.8.8.8, I am still able to connect to anywhere. Does anyone got a clue what is happening here? I will provide any information asked. Thanks in advance p.s. I run Ubuntu 13.04 since lastnight(24-06-2013)

  Read the article

• Not able to connect to local network

  - by Roopesh

  I have installed Kubuntu , I am able to connect to Internet and able to access external sites, but in my local network i have bugzila installed that i am not able to access, even i am not able to ping the gateway also 192.168.1.1 . below is the result of ifconfig command Please help . Thanks ~# ifconfig eth0 Link encap:Ethernet HWaddr b8:70:f4:da:f9:a8 inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:884 errors:0 dropped:0 overruns:0 frame:0 TX packets:884 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:81131 (81.1 KB) TX bytes:81131 (81.1 KB) wlan0 Link encap:Ethernet HWaddr 68:5d:43:2e:1c:79 inet addr:192.168.1.26 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe2e:1c79/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2446 errors:0 dropped:0 overruns:0 frame:0 TX packets:2324 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1909441 (1.9 MB) TX bytes:393292 (393.2 KB)

  Read the article

• Configuration of the network manager via DBus: how to set the ad hoc mode

  - by Andrea

  I have an hard nut to crack: a nice bottle of italian Chianti wine to the solver! :) To automatically configure Wifi, I first have to kill the network manager and than activate the wifi via the commandline: I do this all automatically in my application and works great. However... it is not the right way to do this. As the user has no network gui anymore to configure some other network access. A much better and transparent way would be to configure wifi directly via network manager over the DBus interface. I was able to configure it, but I wasn't able to set it to ad hoc mode... Searching the web for a while: a lot about configuration in general but nothing related to ad hoc mode. I think the only way to do figure that out is to look into the source code of the network manager...maybe someone already did it and he can answer.

  Read the article

• RTL8192SU-based Wi-Fi adapter disconnects permanently

  - by leventov

  I've already tried all possible (http://ubuntuforums.org/showpost.php?p=10129571&postcount=43) solutions, no progress. I'm in despair. In Windows (on the same machine) this adapter works stably. Device: Trendnet TEW-649UB. System details: Ubuntu 11.10; leventov@leventov-ubuntu:~$ uname -a Linux leventov-ubuntu 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:56:25 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux leventov@leventov-ubuntu:~$ lsusb ... Bus 002 Device 002: ID 0bda:8172 Realtek Semiconductor Corp. RTL8191S WLAN Adapter ... leventov@leventov-ubuntu:~$ dmesg | grep 8712 #current driver [ 8.146510] r8712u: module is from the staging directory, the quality is unknown, you have been warned. [ 8.147113] r8712u: DriverVersion: v7_0.20100831 [ 8.147124] r8712u: register rtl8712_netdev_ops to netdev_ops [ 8.147127] r8712u: USB_SPEED_HIGH with 4 endpoints [ 8.147478] r8712u: Boot from EFUSE: Autoload OK [ 8.551272] r8712u: CustomerID = 0x0000 [ 8.551275] r8712u: MAC Address from efuse = 00:14:d1:6c:52:19 [ 8.551625] usbcore: registered new interface driver r8712u [ 9.501351] r8712u: Loading firmware from "rtlwifi/rtl8712u.bin" [ 10.160471] r8712u: 1 RCR=0x153f00e [ 10.161241] r8712u: 2 RCR=0x553f00e leventov@leventov-ubuntu:~$ lsmod | grep 8712 r8712u 189049 0 t

  Read the article

• How to completely remove wicd from 12.04?

  - by danijelc

  I had issues with WiFi so I removed Network Manager. I booted Windows OS (dual booting Windows 7 and 12.04) to download wicd 1.7.2.4. Extracted it and installed. However, wcid worked properly with Wired Connection but could not connect to WiFi. So, I re-installed Network Manager which works properly now, and wicd connects to WiFi too. As soon as I disconnect from Network Manager, wicd connects only to wired. At this point, I wanted to remove wicd but apt-get returns no wicd installed, can't see it in Synaptic or Software Center, but only in Applications list under Dash home. Of course wcid icon shows connections, and resulting connected, so my system shows both applets for wicd and network manager in the top panel. When running dpkg commands, wicd is not listed as installed package. Any suggestion how to remove wicd? Consider that I started with Ubuntu just few months ago so my knowledge base is limited.

  Read the article

• Toshiba satellite L500 no Wifi anymore!

  - by Benjamin Piller

  I have a Toshiba Satellite L500 with Ubuntu 12.04 and its wifi suddenly stopped working!! I've never seen like that before.. I tried also using external USB wifis but no success. I am not able to turn it on with the function keys nor using rfkill commands and similar WLAN manipulator Commands in the terminal! It was working before for at least 4-5 months!! The computer says it's turned off by hardware. I checked it and the Driver is fine. So why can i not use any Wifi on my computer?? Why it is suddenly disabled? I checked the BIOS too there is enabled the WLAN. I spent 10 hours for searching for solutions but i am out of ideas!!! Please Help!

  Read the article

• m not able to connect to wifi network

  - by Broken Heart

  i had tried every code every idea every thing but i failed wiireless driver broadcom bcm43412 but when i checked pci-id it show not supported my pci id is 14e4:4365 and chip id is BCM43142 i tried edit connection myself to olso but i cannt wat to put in clone mac adress place? device mac adress is the router mac adress but what is clone mac adress i had placed my laptop mac adress in place of clone mac adress bt it doesnot work tried every thing but it not work checked additional driver by going system settings it doesnot contain any drivers,tried internet by cable then it connects then how sholud i correct this plz tell

  Read the article

• My WiFi gets deauthenticated every few minutes or seconds (Reason: 7)

  - by dan

  My Wifi on my new Thinkpad W520 running Natty keeps dropping out and coming back on. Output from dmesg below. Any advice? [30493.687552] wlan0: authenticate with e0:91:f5:ef:7b:b2 (try 1) [30493.689127] wlan0: authenticated [30493.689144] wlan0: associate with e0:91:f5:ef:7b:b2 (try 1) [30493.693592] wlan0: RX AssocResp from e0:91:f5:ef:7b:b2 (capab=0x411 status=0 aid=4) [30493.693595] wlan0: associated [31631.172868] wlan0: deauthenticated from e0:91:f5:ef:7b:b2 (Reason: 7) [31631.211847] cfg80211: All devices are disconnected, going to restore regulatory settings [31631.211868] cfg80211: Restoring regulatory settings [31631.211873] cfg80211: Calling CRDA to update world regulatory domain [31631.215037] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [31631.215042] cfg80211: World regulatory domain updated: [31631.215044] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [31631.215046] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [31631.215049] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [31631.215051] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [31631.215053] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [31631.215055] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [31632.289638] wlan0: authenticate with e0:91:f5:ef:7b:b2 (try 1) [31632.291262] wlan0: authenticated [31632.291276] wlan0: associate with e0:91:f5:ef:7b:b2 (try 1) [31632.295119] wlan0: RX AssocResp from e0:91:f5:ef:7b:b2 (capab=0x411 status=0 aid=4) [31632.295123] wlan0: associated [31886.234836] wlan0: deauthenticated from e0:91:f5:ef:7b:b2 (Reason: 7) [31886.306735] cfg80211: All devices are disconnected, going to restore regulatory settings [31886.306740] cfg80211: Restoring regulatory settings [31886.306744] cfg80211: Calling CRDA to update world regulatory domain

  Read the article

• Only run CRON job if connected to specific wifi network

  - by Herbert

  I am a newbie to scripting on Linux (Lubuntu), but I would like to make a script that runs a cron job only if my laptop is connected to my home wifi. Is this possible? I guess, I could do something with iwconfig and pull the ESSID from there with grep? So far, I tried this and it seems to work: #!/bin/bash # CRON, connected to specific WIFI clear netid=HOFF216 if iwconfig | grep $netid then clear echo "True, we are connected to $netid" rsync ........... else clear echo "False, we are not connected to $netid" fi

  Read the article

• How to prevent WLAN connection from dropping permanently?

  - by Chris

  I have a desktop with a Fritz USB WLAN N stick and tried Ubuntu 12.04. Installation went fine and WLAN is working. However, connection drops permanent. Reconnecting manually fixes it but after a few minutes it drops again. It's connected to a Vodafone 802 box with WLAN N fix set. It seems that it works when I switch off N mode. But I need to test. Can someone confirm this issue or is there another solution? I have another machine with 12.04 (HP 625 laptop) running where connection is stable.

  Read the article

• Problem getting GOBI 2000 HS to work

  - by Zypher

  I've been trying to get my integrated GOBI WWAN card to work under 10.10 for a while now. I was able to get the network manager to see the card after installing the gobi-loader package. I was able to setup the connection, but i cannot establish a connection to Verizon. Below is the output from /var/log/daemon.log as i try to connect. Oct 19 14:29:42 gbeech-x201 AptDaemon: INFO: Quiting due to inactivity Oct 19 14:29:42 gbeech-x201 AptDaemon: INFO: Shutdown was requested Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) starting connection 'Verizon connection' Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 3 -> 4 (reason 0) Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 4 -> 6 (reason 0) Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete. Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started... Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 6 -> 4 (reason 0) Oct 19 14:33:45 gbeech-x201 NetworkManager[1105]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <warn> CDMA connection failed: (32) No service Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 4 -> 9 (reason 0) Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> Marking connection 'Verizon connection' invalid. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <warn> Activation (ttyUSB0) failed. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): device state change: 9 -> 3 (reason 0) Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> (ttyUSB0): deactivating device (reason: 0). Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> Policy set 'Auto SO-GUEST' (wlan0) as default for IPv4 routing and DNS. Oct 19 14:34:46 gbeech-x201 NetworkManager[1105]: <info> Policy set 'Auto SO-GUEST' (wlan0) as default for IPv4 routing and DNS.

  Read the article

• No GUI, No internet connection, please help 12.04

  - by KB_

  I am new to Ubuntu and I tried to install ubuntu server 12.04 on my laptop. now my problem is - I am unable to connect to the internet (I have wifi ONLY connection). ubuntu didn't recognize my built-in wifi on my Toshiba Satellite L505. There is no GUI. I have Terminal only, I tried Sudo apt-get update but i am getting errer msg because of no connection. 1. I need to know if there is any possible way that i can download and install driver for my wifi. 2. what other option do i have to be able to update ubuntu. Thanks KB

  Read the article

• Ask the Readers: How Do You Score Free Wi-Fi While Traveling?

  - by Jason Fitzpatrick

  The holiday season is in full swing and that means many of us will be traveling–and searching for Wi-Fi nodes in the process. Help your fellow readers out by sharing your best Wi-Fi finding tips and tricks. Internet access is a necessity for the modern traveler but finding it is a bit more difficult than simply plugging into your home Wi-Fi. This week we want to hear all about your tips, tricks, and methods for scoring free Wi-Fi service in your interstate (and even international) travels. How do you keep the bounty of the internet flowing to your laptops, netbooks, tablets, and smart phones as you traverse the world? Sound off in the comments with your best tips and then check back on Friday for the What You Said roundup. HTG Explains: Understanding Routers, Switches, and Network Hardware How to Use Offline Files in Windows to Cache Your Networked Files Offline How to See What Web Sites Your Computer is Secretly Connecting To

  Read the article

< Previous Page | 284 285 286 287 288 289 290 291 292 293 294 295  | Next Page >