Search Results

Search found 920 results on 37 pages for 'arun ac'.

Page 29/37 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

  • Can I use this power supply + case combination without causing problems?

    - by evan
    I am putting together a computer with a Antec P180 case and a Thermaltake TR2 RX 650 W power supply. The problem is that the Antec P180 case has a separate compartment for the power supply. With an opening for the on/off switch + ac connector to one side, a wall with a small hole for cables to route through on top, a wall on the bottom, and on the other side a fan which pushes air from the hard drive compartment to the power supply compartment. I think the design of the case assumes the power supplies fan is on the side next to the on/off switch, but the fan on the power supply I have is on top, which makes me worry about overheating the power supply. There is about half an inch between the top of the power supply and the wall and the other fan should keep air flowing to push out the air that the power supply pushes upwards. Do you think this setup should work, or should I go get another power supply? Thanks!! PS: This computer will be running an Ubuntu server, so it will always be on, but the rest of the components shouldn't be generating as much heat as they would on say a gaming machine.

    Read the article

  • Why won't 2GB of ram across 3 of 4 slots work on my motherboard (max 2GB)?

    - by Andrew
    My desktop is an old home-built machine circa 200[5-6] running Ubuntu 11.10 (but this is not relevant because I'm reading available ram from BIOS loading screen), with an ASUS P5GPL motherboard, not X or X-SE - it has four slots. I'm mainly a laptop person, but keep this around for running a server from if needed, backing up to, seeding Ubuntu to people from, etc… It has four (DDR) ram slots, two black and two blue, in the order black-blue-black-blue (I will call them D, C, B, and A, respectively) with some space in the middle. The blue ones are the closest to the processor. I used to have two 512MB chips in the two blue slots. I just got a 1GB chip and plugged it into one of the black slots; my system didn't recognize it. I messed around and discovered that it will not recognize chips in many positions, and I couldn't get it to recognize all three of these chips at the same time. In particular, if I put the 512MB chips in A and B it would only use 1, but AC, AD, BD, and CD worked. I didn't try BC, I believe. Only some of these continue to work when I switch the 1GB chip into one of these positions. Can I have some advice as to how to position these chips to get all 2GB used? How about if I get another 1GB chip - where should I put the two? And what about the RAM maximum Crucial says? Can I go above 2GB, if I get another 1GB chip? Right now, I have a 512MB chip in A and the 1GB chip in C. EDIT: I read some other posts and tried dmidecode in Ubuntu to clarify the max memory question, that wasn't a major part anyways. It says my max memory module size is 1024M (OK) and my max memory size is 4096M (doesn't agree with Crucial OR the Asus web site, maybe it will only work while in Linux and BIOS won't OK it?).

    Read the article

  • Filtering bad requests from Apache -> logger -> rsyslog to syslog-ng on a remote logging server possible?

    - by zeyus
    EDIT: Thanks for the help Here is a quick idea of the setup: webserver X In apache httpd.conf: LogFormat "%v %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" vcombined CustomLog "|/usr/bin/logger -p local6.info -t access " vcombined In rsyslog.conf: *.* @logserver Logserver syslog-ng.conf: ... parser p_apache {csv-parser(columns( "APACHE.VIRTUAL_HOST", "APACHE.CLIENT_IP", "APACHE.IDENT_NAME", "APACHE.USER_NAME", "APACHE.TIMESTAMP", "APACHE.REQUEST_URL", "APACHE.REQUEST_STATUS", "APACHE.CONTENT_LENGTH", "APACHE.REFERER", "APACHE.USER_AGENT", "APACHE.PROCESS_TIME", "APACHE.SERVER_NAME") # flags: # escape-none,escape-backslash,escape-double-char, # strip-whitespace flags(escape-double-char,strip-whitespace) delimiters(" ") quote-pairs('""[]') );}; ... source s_net { udp(ip(0.0.0.0) port(514) so_rcvbuf(1048576)); }; destination hosts_acc { file("/var/log/hosts/$HOST/${APACHE.VIRTUAL_HOST}_acc.log"); }; filter f_apacheacc { facility(local6); }; log { source(s_net); parser(p_apache); filter(f_apacheacc); destination(hosts_acc); }; ... The log's get there just fine, but there are a LOT of logs like the following: -rw------- 1 root root 5726 Apr 6 01:02 xc3\x9d\xc3\x9ed$yA;_acc.log -rw------- 1 root root 23435 Apr 6 01:06 \xc3\x9ed$yA;_acc.log -rw------- 1 root root 745 Apr 6 00:57 xc3\x9ed$yA;_acc.log -rw------- 1 root root 8440 Apr 5 22:50 \xc3\xaf_F\xc3\x95$yA;_acc.log -rw------- 1 root root 3112 Apr 6 00:58 xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA;_acc.log -rw------- 1 root root 4220 Apr 5 22:03 xe2\x80\x98\twd\xc2\xa2\xc2\xb0\xc3\x96$yA;_acc.log -rw------- 1 root root 1055 Apr 5 22:03 xe2\x80\x98\xc2\x9dw\xc3\x94\xc3\xb4T\xc5\x93$yA;_acc.log -rw------- 1 root root 1821 Apr 6 00:58 \xe2\x80\x98\xc3\x9d\xc3\x9ed$yA;_acc.log -rw------- 1 root root 2875 Apr 6 01:02 xe2\x80\x98\xc3\x9d\xc3\x9ed$yA;_acc.log -rw------- 1 root root 3165 Apr 5 22:48 \xe2\x80\x99-w\xc3\xaf_F\xc3\x95$yA;_acc.log -rw------- 1 root root 3165 Apr 5 22:40 \xe2\x80\x99\xe2\x80\x9aw\xe2\x82\xac\xc2\xbd\xe2\x80\x9d($yA;_acc.log -rw------- 1 root root 15825 Apr 5 22:50 xe2\x80\x99\xe2\x80\x9aw\xe2\x82\xac\xc2\xbd\xe2\x80\x9d($yA;_acc.log -rw------- 1 root root 1055 Apr 5 22:39 \xe2\x80\x9aw\xe2\x82\xac\xc2\xbd\xe2\x80\x9d($yA;_acc.log -rw------- 1 root root 2110 Apr 5 22:50 xe2\x80\x9aw\xe2\x82\xac\xc2\xbd\xe2\x80\x9d($yA;_acc.log -rw------- 1 root root 2034 Apr 5 22:50 \xe2\x80\x9d($yA;_acc.log -rw------- 1 root root 4066 Apr 5 22:45 xe2\x80\x9d($yA;_acc.log -rw------- 1 root root 7212 Apr 6 13:30 \xe2\x80\xb9>$yA;_acc.log -rw------- 1 root root 3000 Apr 6 13:25 xe2\x80\xb9>$yA;_acc.log My question is where, and how can I filter these out, I don't want them on the filesystem (But actually I guess it wouldn't be a bad idea to keep them logged, but in their correct VHost file) Here is an example VHost <VirtualHost *:80> ServerAdmin [email protected] ServerName xxx.xx DocumentRoot /var/www/vhosts/xxx <Directory /var/www/vhosts/xxx> AllowOverride All Options All RewriteEngine on </Directory> </VirtualHost> And the default "catch-all" vhost at the bottom of the vhosts config file: <VirtualHost *:80> ServerName default ServerAlias * ServerAlias catchall.xxx.xx DocumentRoot /var/www/vhosts/nodomain <Directory "/var/www/vhosts/nodomain"> Options Indexes FollowSymLinks AllowOverride none Allow from All </Directory> CustomLog /dev/null combined ErrorLog /dev/null </VirtualHost> I had posted this in a related question but It's better in it's own question. Here are some examples from inside the log files r_acc.log: Apr 7 11:16:27 xxxxx access: r PC 5.0; eSobiSubscriber 2.0.4.16; .NET CLR 3.5.30729; .NET CLR 3.0.30729; .NET4.0C)" Apr 7 11:16:28 xxxxx access: r PC 5.0; eSobiSubscriber 2.0.4.16; .NET CLR 3.5.30729; .NET CLR 3.0.30729; .NET4.0C)" ######################## D46-28E2-0FBC95-78798EV\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA;_acc.log: Apr 7 14:54:06 xxxxx access: D46-28E2-0FBC95-78798EV\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA; B557000E-F20D-35DD-021A-9824EC-17A4AFV\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA; 3BD03D7B-EEFD-83FF-7599-B751AD-6F0A2EV\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA; 9CAE0724-D455-0B31-3378-871C11-BBD0A4V\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA; C1E24799-3979-2452-81-3BAA0FFD361F5A; 0E701CBC-5832-5AB6-D5-CFBF9BDE863EAA; 464714B1-B3E2-774A-A4-FEA612A46CEE06; 74C817B0-D081-D2CC-6D-C4EF0F1B4F49BB; 1338B1DE-67CD-977C-B35D-1F2C4441DD6A; SLCC1; .NET CLR 2.0.50727; Media Center PC 5.0; .NET CLR 1.1.4322; .NET CLR 3.5.30729; .NET CLR 3.0.30729; OfficeLiveConnector.1.5; OfficeLivePatch.1.3; .NET4.0C; BRI/2)" ######################## V\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA;_acc.log: Apr 7 14:55:04 xxxxx access: V\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA; FEEACE4F-092A-1D46-28E2-0FBC95-78798EV\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA; B557000E-F20D-35DD-021A-9824EC-17A4AFV\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA; 3BD03D7B-EEFD-83FF-7599-B751AD-6F0A2EV\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA; 9CAE0724-D455-0B31-3378-871C11-BBD0A4V\xe2\x80\x94w\xe2\x80\x98\xc3\x9d\xc3\x9ed$yA; C1E24799-3979-2452-81-3BAA0FFD361F5A; 0E701CBC-5832-5AB6-D5-CFBF9BDE863EAA; 464714B1-B3E2-774A-A4-FEA612A46CEE06; 74C817B0-D081-D2CC-6D-C4EF0F1B4F49BB; 1338B1DE-67CD-977C-B35D-1F2C4441DD6A; SLCC1; .NET CLR 2.0.50727; Media Center PC 5.0; .NET CLR 1.1.4322; .NET CLR 3.5.30729; .NET CLR 3.0.30729; OfficeLiveConnector.1.5; OfficeLivePatch.1.3; .NET4.0C; BRI/2)" ################### xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA;_acc.log: Apr 7 19:48:39 xxxxx access: xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; 3C12D25C-9D40-91CF-1F40-AC-B1A083426DV-w\xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; D4713FA8-0142-A0C2-4812-BA-E03221005BV-w\xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; 199BAF2A-ECD5-39FA-65C3-E8-B107FAFF08V-w\xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; 384BDA70-9954-7744-05A0-C4-C7D9FEA685V-w\xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; EE7292A9-333C-AF70-5A7F-55-CAA7D0BA39V-w\xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; -AD7D48FA3A55-2A33-D10B-B4B66276D8B8; -166A9C6A2E71-24DF-A192-C8258AA4DE14; -00077C6C84E0-A302-4954-3D6D17C54D31; 3F56C318-EC3C-432B-680F-7E4BB2B852C4; SLCC1; .NET CLR 2.0.50727; .NET CLR 3.5.21022; .NET CLR 3.5.30729; .NET CLR 3.0.30729; .NET4.0C)" Apr 7 19:48:39 xxxxx access: xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; 3C12D25C-9D40-91CF-1F40-AC-B1A083426DV-w\xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; D4713FA8-0142-A0C2-4812-BA-E03221005BV-w\xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; 199BAF2A-ECD5-39FA-65C3-E8-B107FAFF08V-w\xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; 384BDA70-9954-7744-05A0-C4-C7D9FEA685V-w\xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; EE7292A9-333C-AF70-5A7F-55-CAA7D0BA39V-w\xc2\x90\xc3\x91\xc3\x94\xc2\xab$yA; -AD7D48FA3A55-2A33-D10B-B4B66276D8B8; -166A9C6A2E71-24DF-A192-C8258AA4DE14; -00077C6C84E0-A302-4954-3D6D17C54D31; 3F56C318-EC3C-432B-680F-7E4BB2B852C4; SLCC1; .NET CLR 2.0.50727; .NET CLR 3.5.21022; .NET CLR 3.5.30729; .NET CLR 3.0.30729; .NET4.0C)" Thanks

    Read the article

  • Unix Permissions issue with users belonging to the same group accessing a folder

    - by TK Kocheran
    I have a folder I'd really like to allow another user on this machine access to. I'm using mt-daapd to serve music to the network, so I'd like to enable the mt-daapd user to access my Music directory, /home/rfkrocktk/Music. The master user is rfkrocktk obviously. I've tried to set all of my permissions properly on the directory, but the mt-daapd user can't acces the files. I created a group called media-users and added both rfkrocktk and mt-daapd to it in order to give mt-daapd permission to simply read all of the files in that directory and subdirectories. If I run id on each of my users, here's what's displayed: $ id rfkrocktk > uid=1000(rfkrocktk) gid=1000(rfkrocktk) groups=1000(rfkrocktk),4(adm),20(dialout),24(cdrom),29(audio),46(plugdev),104(lpadmin),115(admin),120(sambashare),124(vboxusers),1001(jupiter),2002(media-users) $ id mt-daapd > uid=123(mt-daapd) gid=65534(nogroup) groups=65534(nogroup),2002(media-users) It definitely seems that both users are a part of the media-users group, so what could be going wrong? If I run ls -l on the actual Music directory to see its permissions, here's the output: drwxr-Sr-- 201 rfkrocktk media-users 12288 2011-01-13 12:26 Music If I run ls -l on the Music directory to get its children, here's the output: drwxr-Sr-- 3 rfkrocktk media-users 4096 2010-12-20 15:31 2DBoy drwxr-Sr-- 3 rfkrocktk media-users 4096 2010-05-25 12:50 ABBA drwxr-Sr-- 3 rfkrocktk media-users 4096 2009-12-28 15:19 Access Denied drwxr-Sr-- 10 rfkrocktk media-users 4096 2009-12-28 15:19 AC-DC drwxr-Sr-- 3 rfkrocktk media-users 4096 2009-12-28 15:19 Aerosmith drwxr-Sr-- 3 rfkrocktk media-users 4096 2010-06-04 10:45 A Flock of Seagulls drwxr-Sr-- 4 rfkrocktk media-users 4096 2010-05-28 18:13 Alestorm drwxr-Sr-- 3 rfkrocktk media-users 4096 2010-06-22 23:29 Amon Amarth drwxr-Sr-- 5 rfkrocktk media-users 4096 2009-12-28 15:19 Anberlin ... From this, it would seem that I should be able to access the folders from mt-daapd, but I can't. Running sudo -i -u mt-daapd ls -l /home/rfkrocktk/Music displays nothing, indicating to me that for whatever reason, mt-daapd doesn't have access to read the folder. What am I doing wrong?

    Read the article

  • Bridged network on OS X only gets UDP broadcast traffic

    - by a paid nerd
    I've created a bridged network Mac OS X 10.8.5 using ifconfig and TUNTAP for OS X to bridge my wireless connection, en0, with a virtual interface, tap0, which I can use for guest VMs: $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 28:cf:xx:xx:xx:xx inet6 xxxx::xxxx:xxxx:xxxx:xxxx%en0 prefixlen 64 scopeid 0x4 inet 192.168.100.64 netmask 0xffffff00 broadcast 192.168.100.1 media: autoselect status: active bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) However, if I tcpdump -i tap0, I only see broadcast traffic. Shouldn't I see a mirror of everything on en0? (192.168.100.33, the host doing the broadcasting, is another unrelate, noisy server on my LAN.) (I asked a similar question here and will probably close it.)

    Read the article

  • XTerm and a bold text

    - by user610378
    This is my Xterm config: XTerm*saveLines: 512 XTerm*reverseVideo: false XTerm*reverseWrap: true XTerm*fullCursor: true XTerm*scrollTtyOutput: on XTerm*scrollKey: on XTerm*eightBitInput: false XTerm*pointerColor: white XTerm*pointerShape: left_ptr XTerm*charClass: 37:48,45-47:48,58:48,64:48,126:48 XTerm*cursorColor: rgb:aa/aa/aa XTerm*cursorColor2: black XTerm*color0: rgb:71/71/71 XTerm*color1: rgb:cd/00/00 XTerm*color2: rgb:b4/cd/00 XTerm*color3: rgb:cd/cd/00 XTerm*color4: rgb:71/71/71 XTerm*color5: rgb:cd/00/cd XTerm*color6: rgb:00/cd/cd XTerm*color7: rgb:e5/e5/e5 XTerm*color8: rgb:4c/4c/4c XTerm*color9: rgb:ff/00/00 XTerm*color10: rgb:55/ac/55 XTerm*color11: rgb:ff/ff/00 XTerm*color12: rgb:46/82/b4 XTerm*color13: rgb:ff/00/ff XTerm*color14: rgb:00/ff/ff XTerm*color15: rgb:ff/ff/ff XTerm*colorBD: white XTerm*colorUL: SkyBlue XTerm*colorBDMode: on XTerm*colorULMode: on XTerm*underLine: on XTerm*background: rgb:30/0a/24 XTerm*foreground: white XTerm*font: -*-monospace-medium-r-normal-9-140-*-*-m-*-* XTerm*font1: 5x7 XTerm*font2: 6x10 XTerm*font3: fixed XTerm*font4: 9x15 XTerm*ScrollBar.Background: gray XTerm*ScrollBar.thickness: 0 XTerm*ScrollBar.foreground: gray XTerm*ScrollBar: false XTerm*ScrollBar.DrawBorder: false XTerm*loginShell: true XTerm*faceName: Mono XTerm*faceSize: 9 Could anyone say is it possible to make bold some text, wich color is e.g. color1 from my config? I've tried XTerm*color1: rgb:cd/00/00 bold, but this doesn't work.

    Read the article

  • Nvidia GTS 360M in Asus laptop shuts off when gaming on external display

    - by mr odus
    I have had this problem on my Asus G51j Intel I5, Nvidia GTS360M graphics card. Just updated the drivers to latest off Nvidias site. Most games I play, If I hook it up through an external monitor(this happens whether it's HDMI or VGA). The laptop hard shuts down after about 20 minutes, give or take. This tends to happen on more graphically intense games like Call of dutys, bioshock. I'm running Windows 7, latest nvidia drivers. Games work fine on my laptops screen, and Movies, general computing work fine on the external displays. The laptop always sits on a cooling pad and the latest time was in front of my AC unit, I ran heatfan or whatever the heat tracking software was, and my temperatures were normal through a shut down. This has been happening for the life of the laptop. I dont play very many games, and even fewer on an external monitor, so this issue doesnt come up much Is it possible I have a faulty graphics card? Is there anything else I can try?

    Read the article

  • Switch Windows 8 from a hybrid MBR/GPT => GPT only on Macbook Pro Retina

    - by Sid
    I used DiskUtility+Bootcamp Wizard to setup my hard drive for Windows 8 (final MSDN). Somewhere in that process, the Apple tools turned my GPT disk into a hybrid MBR/GPT. All my 4 primary MBR partitions are used up, so when I try turning on Bitlocker in Windows 8, it complains about not finding a System drive. I know on Windows 8 the Bitlocker setup tries to create the 200(?)MB system partition if it's missing. However with all 4 partitions filled I suspect it can't create system drive = it can't find it = throws back an error like "BitLocker Setup could not find a target system drive. You may need to manually prepare your drive for BitLocker". I've already tried disabling hibernation, swap file etc. Now I'm thinking that if I were to get rid of the MBR scheme altogether, perhaps I can be alright within the GPT world without MBR's 4 primary partitions limit. So, how can I get rid of the MBR tables on the hybrid scheme in a manner that still leaves Mac OS and Windows 8 in working conditions? Details: Hardware is the MacbookPro Retina. Primary MBR partitions are consumed as follows: EFI partition HFS+ partition (=encrypted, therefore ="Apple_CoreStorage") HFS+ partition (Recovery partition, contains unencrypted Mac bootloader) NTFS partition (Windows8 all-in-one partition) diskutil list output sid-mbpr:~ sid$ diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *251.0 GB disk0 1: EFI 209.7 MB disk0s1 2: Apple_CoreStorage 160.0 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 4: Microsoft Basic Data Win8 90.1 GB disk0s4 GPT vs MBR addresses sid-mbpr:~ sid$ sudo gptsync /dev/rdisk0 Password: Current GPT partition table: # Start LBA End LBA Type 1 40 409639 EFI System (FAT) 2 409640 312909639 Unknown 3 312909640 314179175 Mac OS X Boot 4 314179584 490233855 Basic Data Current MBR partition table: # A Start LBA End LBA Type 1 1 409639 ee EFI Protective 2 409640 312909639 ac Apple RAID 3 312909640 314179175 ab Mac OS X Boot 4 * 314179584 490233855 07 NTFS/HPFS Status: GPT partition of type 'Unknown' found, will not touch this disk.** **: Ignore this message, the gptsync tool is old and doesn't understand the UUID for "Apple_CoreStorage" / FileVault2 partitions. Since LBA addresses are alright, safe to ignore this message.

    Read the article

  • Intel D2500HN Atom D2500 Doesn't turn on

    - by David W
    I recently bought parts from Amazon to build an embedded PC, and have assembled everything. I have: Intel D2500HN Mini-ITX Motherboard Mini-Box Pico-PSU 80 M350 Universal Min-ITX Enclosure 2GB DDR3 Memory Kinamax AD-LCD12 LCD Monitors 12V 6A 72W AC Adapter Power Supply The motherboard gets a light (on the motherboard, not on the Pico-PSU) when I plug it into the power adapter. Furthermore, I see the power switch light come on when I press the power button. However, the display doesn't turn on, and it doesn't seem that the PC is actually turned on. Since I'm seeing these lights, I know that the motherboard is getting power. Furthermore, the display VGA port is embedded into the motherboard, so that's not the issue. I'm just trying to figure out what COULD be the issue aside from a faulty motherboard. I have a diagram of the D2500HN motherboard which labels everything, and have ensured that the power LED as well as the On/Off cables are plugged into the right spots, although to be sure I've tried flipping these two cables around, and also plugging 1 cable into the other cable's spot & vice-versa. Is there anything else you folks think I may be missing, or anything else I can do to try to troubleshoot this issue before sending the motherboard back?

    Read the article

  • Is it possible to install ffmpeg and x264 on a Synology Diskstation 209?

    - by Kieran Benton
    Hi, Complete linux novice here! :) I'm trying to get my brilliant DS209 NAS box to do some transcoding for me of a few AVI videos to a format suitable for my Apply iTouch - yes I could do it with another machine and Handbrake but it would be really useful to offload some of this to the NAS to do overnight. I've managed to install ipkg onto my DS209 NAS box and have played around with installing some packages (binutils, mono, bash etc). I've even managed to install ffmpeg from ipkg and put together the correct command line profile to do the encoding as a .sh file: time ffmpeg -y -i $1 -f mp4 -title $2 -vcodec libx264 -level 21 -s 426×320 -b 512k -bt 512k -bufsize 4M -maxrate 4M -g 250 -coder 0 -threads 0 -acodec libfaac -ac 2 -ab 64k $3 However running this I get a missing dependency on libx264. I've tried building this from the latest source in git, but I get errors during the make process that I just don't understand (way out of my depth). encoder/set.c: In function 'x264_sei_version_write': encoder/set.c:491: error: 'X264_VERSION' undeclared (first use in this function) encoder/set.c:491: error: (Each undeclared identifier is reported only once encoder/set.c:491: error: for each function it appears in.) make: *** [encoder/set.o] Error 1 Can anyone else try building it or give me a pointer as to what I can do to get this going? Its been a good learning experience so far! Thanks.

    Read the article

  • Routing data through VPN in linux

    - by Shadyabhi
    I think its a silly question but still here it goes.. Terminal Output: eth0 Link encap:Ethernet HWaddr 00:1c:c0:37:5e:25 inet addr:10.100.98.51 Bcast:10.100.98.255 Mask:255.255.255.0 inet6 addr: fe80::21c:c0ff:fe37:5e25/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:29677 errors:0 dropped:0 overruns:0 frame:0 TX packets:5209 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3179007 (3.1 MB) TX bytes:610142 (610.1 KB) Memory:e0380000-e03a0000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:9555 (9.5 KB) TX bytes:9555 (9.5 KB) vpn_0 Link encap:Ethernet HWaddr 00:ac:39:95:a1:16 inet6 addr: fe80::2ac:39ff:fe95:a116/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1786 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:128597 (128.5 KB) TX bytes:468 (468.0 B) Actually, I followed this tutorial to setup the PacketiX VPN on ubuntu. Now, how do I actually use this VPN? Terminal Output: shadyabhi@shadyabhi-desktop:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 shadyabhi@shadyabhi-desktop:~$ As told in tutorial, if I do route del default route add default dev vpn_0 I am not able to surf the internet. And I get the route command output as: root@shadyabhi-desktop:/home/shadyabhi# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default * 0.0.0.0 U 0 0 0 vpn_0 root@shadyabhi-desktop:/home/shadyabhi# I know I am not able to route the traffic properly. How do i do that?

    Read the article

  • changing filesystem format from xfs to ext4 without losing data

    - by A.Rashad
    I have a fresh Lucid Lynx (Ubuntu 10.04) running on a laptop. where I defined the filesystems as: mount point / on ext4 (46 Gb) mount point /home on jfs (63 GB) swap as 3 Gb I left the machine over night to do some task, without AC power supply. next day in the morning I found it on standby, task completed, but filesystem was not reachable. it gave me I/O error it seems that there is a problem with jfs and standby. anyways, to avoid any hassle, I want to move this mount point from jfs format to ext4. can I do this without losing data and without the need to place the data in a temporary location until transformation is done? sorry to mention that, but I recall back in the windows days, we would change a FAT16 to FAT32 or a FAT32 to NTFS without having to lose the data. I hope this is available on Linux. Update The /home filesystem was xfs not jfs, and it seems there is a bug with this filesystem for some reason, I had to re-install the OS twice until I ended up with ext4 for the entire / However, as a conclusion, it seems that there is no way to make a conversion

    Read the article

  • Unstable DNS with bind

    - by yasser abd
    we have a Centos machine called jupiter, on which I have installed bind9, On every other machine the DNS is set to be the IP address of jupiter (192.168.2.101), as you can see in the output of the following command in windows >ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : mypcs Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme 57xx Gigabit Controller Physical Address. . . . . . . . . : 00-1A-A0-AC-E4-CC DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::c16d:3ae4:5907:30c4%8(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.2.98(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Thursday, September 20, 2012 10:26:11 AM Lease Expires . . . . . . . . . . : Sunday, September 23, 2012 10:26:10 AM Default Gateway . . . . . . . . . : 192.168.2.1 DHCP Server . . . . . . . . . . . : 192.168.2.1 DHCPv6 IAID . . . . . . . . . . . : 201333408 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-16-3A-50-01-00-1A-A0-AC-E4-CC DNS Servers . . . . . . . . . . . : 192.168.2.101 192.168.2.1 192.168.2.1 NetBIOS over Tcpip. . . . . . . . : Enabled All machines can always nslookup one of the domain (mydomain.com) that is set in the jupiter's DNS server, you can see that in the output of nslookup on the same windows machine: >nslookup mydomain.com Server: UnKnown Address: 192.168.2.101 Name: mydomain.com Address: 192.168.2.100 The problem is, sometimes mydomain.com can not be pinged, here is the output of the ping on the same windows machine >ping mydomain.com Ping request could not find host mydomain.com. Please check the name and try again. This looks very random, and happens once in a while, so the machine can lookup the DNS records but can't ping it, nor can browse the website that is hosted on mydomain.com, which should resolve to 192.168.2.100 On a linux machine that has the same DNS settings, the output of dig command for mydomain is as follows: $ dig mydomain.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6_3.2 <<>> mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 36090 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 1, ADDITIONAL: 1 ;; QUESTION SECTION: ;mydomain.com. IN A ;; ANSWER SECTION: mydomain.com. 86400 IN A 192.168.2.100 ;; AUTHORITY SECTION: mydomain.com. 86400 IN NS jupiter. ;; ADDITIONAL SECTION: jupiter. 86400 IN A 192.168.2.101 ;; Query time: 1 msec ;; SERVER: 192.168.2.101#53(192.168.2.101) ;; WHEN: Thu Sep 20 16:32:14 2012 ;; MSG SIZE rcvd: 83 We've never had the same problem on MACs, they always resolve mydomain.com Here is how I have defined mydomain.com on Bind9's configs on Jupiter, notice that the name of the machine on 192.168.2.100 is venus, so I have this file: /var/named/named.venus: $TTL 1D @ IN SOA jupiter. admin.ourcompany.com. ( 2003052800 ; serial 86400 ; refresh 300 ; retry 604800 ; expire 3600 ; minimum ) @ IN NS jupiter. @ IN A 192.168.2.100 * IN A 192.168.2.100 /var/named/zones/named.venus.zone zone "mydomain.com" IN {type master;file "/var/named/named.venus";allow-update {none;};}; One thing to note is that I haven't defined reverse DNS lookups, only the forward DNS lookups are defined in Bind9 configs, not sure if that's relevant or not. So my question is, why is this being so unstable? what could be the cause?

    Read the article

  • How do I create a wifi network bridge with qemu on OS X?

    - by a paid nerd
    I grabbed a small FreeBSD live CD and QEMU, and I'm trying to bridge my Mac OS X 10.8 wifi connection so that the guest OS is available on my LAN. However, the guest OS never gets a DHCP lease. This works perfectly with VirtualBox in their "bridged" network mode, so I know it can be done. I need to get it working with QEMU because VirtualBox doesn't support the architecture that I need for this project. Here's what I've done so far based on hours of googling: Installed TUNTAP for OS X Told OS X to supposedly forward all packets, even ARP: (NOTE: This doesn't appear to work.) $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 Created a bridge: $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) Started tcpdump with -I in the hopes that it enables promiscuous mode on the wifi device: $ sudo tcpdump -In -i en0 Run QEMU using the bridged network instructions: $ qemu-system-x86_64 -cdrom mfsbsd-9.2-RELEASE-amd64.iso -m 1024 \ -boot d -net nic -net tap,ifname=tap0,script=no,downscript=no But the guest system never gets a DHCP lease: If I tcpdump -ni tap0, I see lots of traffic from the wireless network. But if I tcpdump -ni en0, I don't see any DHCP traffic from the QEMU guest OS. Any ideas? Update 1: I tried sudo defaults write "/Library/Preferences/SystemConfiguration/com.apple.Boot" "Kernel Flags" "net.inet.ip.scopedroute=0" and rebooting per this mailing list suggestion, but this didn't help. In fact, it made VirtualBox bridged mode stop working.

    Read the article

  • Burn .srt subtitles to AVC encoded video (transcoding with hardsubs) [closed]

    - by Saxtus
    Possible Duplicate: How do I hard code a movie with subtitles? I am looking for a software (or combination of software) that will allow me to hard burn subtitles from an .srt file, that has italics and bold typefaces, to an H.264/AVC encoded video so it can played from a desktop player that can't display external subtitles correctly. Ideally it could use Directshow as input as DirectVobSub makes nice job showing the subtitles as they should (allowing me to globally adjust font and size). CUDA use, to speed up encoding, will be great but not necessary. Video source is also H.264/AVC encoded. Audio is AC-3 5.1 and should be retained too but I have no problem re-muxin it later as long as it keeps synced. Until now I've unsuccessfully tested: Avisynth 2.58 Unable to make Direcvobsub to launch through it TextSub() command renders subtitles with fixed font/size and doesn't decode tags Malformed audio TMPGEnc 4.0 XPress 4.7.4.299 Audio downmixed to 2.0 Importing of subtitles doesn't decode tags Badaboom 1.2.1.7 No importing of subtitles at all SUPER © 2010.build.37 "Directshow decode" has similar effect as Avisynth above Other modes doesn't appear to allow any subtitles in Thank you.

    Read the article

  • ffmpeg: converting an avi to a reduced, shareable flv/mp4...

    - by meder
    I recently followed a guide and recompiled my ffmpeg so x264 is enabled. I used some generic settings to convert my 700 MB avi file to a mp4 file, the result was a 407MB mp4 file. The original avi file's settings: Codec: DX50 Resolution: 704x304 Frame rate: 23.976023 Stream 1 Codec: mpga Type: Audio Channels: 2 Sample rate: 48000 Hz Bitrate 179 kb/s Command I used: ffmpeg -i input.avi -acodec libfaac -ab 128k -ac 2 -vcodec libx264 -vpre hq -crf 22 -threads 0 output.mp4 The settings of the output file (output.mp4): Codec: avc1 Resolution: 704x304 Display resolution: 704x304 Frame rate: 11.988011 Stream 1 Codec: mp4a Type: Audio Channels: 2 Sample Rate: 48000 Hz Bits per sample: 16 Bitrate: 1536 kb/s The quality of the output mp4 is pretty nice, it seems as if it's pretty much the same as the original source. However, I'm trying to reduce the filesize and I'm not really sure whether I should go with an flv format or keep it mp4. The advantage the flv would have obviously is that it would be playable with a flash player ( I have come across some swf players which take a flash parameter to play an flv file ).. but maybe I could use the video element, as I'm only going to be displaying this video privately so I don't have to worry about supporting legacy browsers such as IE. Can someone recommend some settings to specify in order for the filesize to be around ~100-150MB or so? I don't mind a reduction in quality, nor do I mind resizing it - I was going to do it initially but I wasn't sure what the guidelines were ( if any ) for dealing with resolution.. since this video's is 704x304 would it still be ok if I forced it into one that isn't perfectly fit for the aspect ratio? I have no clue about that part. I realize that I could have probably specified 28 instead of 22 for the CRF, I'm not sure if I should do that as opposed to maybe specifying smaller resolution, which might make it smaller as well?

    Read the article

  • ESXi - change to thin - virtual disk filesize is the same

    - by sven
    running ESXi 5.5 here with a datastore on a single SSD. Now, I thought about changing to thin disks from thick and found that I could use a tool on the ESXi host to do that. However, the file size of the new created virtual disk is not changing. I run: vmkfstools -i loader.vmdk -d 'thin' thinloader.vmdk Destination disk format: VMFS thin-provisioned Cloning disk 'loader.vmdk'... Clone: 100% done. After that I compared the virtual disksizes: ls -la *.vmdk -rw------- 1 root root 32212254720 Jun 10 08:25 loader-flat.vmdk -rw------- 1 root root 467 May 21 17:04 loader.vmdk -rw------- 1 root root 32212254720 Jun 10 08:27 thinloader-flat.vmdk -rw------- 1 root root 520 Jun 10 08:33 thinloader.vmdk Stats on the original file: stat loader.vmdk File: loader.vmdk Size: 467 Blocks: 0 IO Block: 131072 regular file Device: 8bf64d175e27544ch/10085333178302026828d Inode: 419443780 Links: 1 Access: (0600/-rw-------) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2014-01-25 10:17:34.000000000 Modify: 2014-05-21 17:04:06.000000000 Change: 2014-05-21 17:04:06.000000000 and on the thin file: stat thinloader.vmdk File: thinloader.vmdk Size: 520 Blocks: 0 IO Block: 131072 regular file Device: 8bf64d175e27544ch/10085333178302026828d Inode: 432026692 Links: 1 Access: (0600/-rw-------) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2014-06-10 08:27:45.000000000 Modify: 2014-06-10 08:33:30.000000000 Change: 2014-06-10 08:33:30.000000000 Anyone an idea why the disk is not providing any more space (tried with multiple VM's already - all the same)? Also, I have noticed that the newly created file "autoappend" "-flat" to the disk ... Thanks Sven Update - diff of the vmdk config* --- loader.vmdk +++ thinloader.vmdk @@ -7,15 +7,17 @@ createType="vmfs" -RW 62914560 VMFS "loader-flat.vmdk" +RW 62914560 VMFS "thinloader-flat.vmdk" ddb.adapterType = "lsilogic" +ddb.deletable = "true" ddb.geometry.cylinders = "3916" ddb.geometry.heads = "255" ddb.geometry.sectors = "63" ddb.longContentID = "6d95855805dfa0079327dfee29b48dca" -ddb.uuid = "60 00 C2 98 d5 7d 17 bf-ac 54 70 b1 2d 39 43 d5" +ddb.thinProvisioned = "1" +ddb.uuid = "60 00 C2 93 c4 13 6c cf-bb 7b 34 c9 2c b4 dc 1e" ddb.virtualHWVersion = "8"

    Read the article

  • Not able to run firefox in a head-less Ubuntu server 9.10

    - by Julio J.
    I need to run Firefox in my server in order to execute some Selenium tests from Hudson. I would love no to have to install a complete gui. So I installed Xvfb in order to fake the Gui (I understand it this way correct me if my assumptions are wrong). After some time trying to make it work, I'm stuck with the next situation: $ sudo Xvfb -ac :99 & [dix] Could not init font path element /var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType, removing from list! (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) $ firefox [dix] Could not init font path element /var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType, removing from list! [config/dbus] couldn't register object path (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) (EE) config/hal: NewInputDeviceRequest failed (2) Xlib: extension "RANDR" missing on display ":99.0". GConf Error: Failed to contact configuration server; some possible causes are that you need to enable TCP/IP networking for ORBit, or you have stale NFS locks due to a system crash. See http://projects.gnome.org/gconf/ for information. (Details - 1: Failed to get connection to session: /bin/dbus-launch terminated abnormally without any error message) I'm runnig firefox without installing it from the repositories. And I'm getting a socket timeout when I try to run the selenium tests, so I guess the problem is in Firefox and Xvfb. I have installed already the nex package: i gconf-defaults-service - GNOME configuration database system (system defaults service) That in some forums suggest to be a fix, that in my case doesn't work. Any explanation about the problem and ways of solving it without installing a full gui, will be very helpful.

    Read the article

  • Disabling Keyboard Wakeup for Ubuntu 10.04 on Acer 1810TZ

    - by sybreon
    My Acer Aspire 1810TZ laptop suspends fine but wakes up on any slight key-press. I would like to disable this behaviour. I read that it involves disabling something in the /proc/acpi/wakeup but SLPB does not seem to be listed at all. root@1810TZ:/etc# cat /proc/acpi/wakeup Device S-state Status Sysfs node UHC0 S3 disabled pci:0000:00:1d.0 UHC1 S3 disabled pci:0000:00:1d.1 UHC2 S3 disabled pci:0000:00:1d.2 UHCR S3 disabled EHC1 S3 disabled pci:0000:00:1d.7 UHC3 S3 disabled pci:0000:00:1a.0 UHC4 S3 disabled UHC5 S3 disabled EHC2 S3 disabled pci:0000:00:1a.7 EXP1 S4 disabled pci:0000:00:1c.0 PXSX S4 disabled pci:0000:01:00.0 EXP2 S4 disabled PXSX S4 disabled EXP3 S4 disabled PXSX S4 disabled EXP4 S4 disabled pci:0000:00:1c.3 PXSX S4 disabled pci:0000:02:00.0 EXP5 S4 disabled PXSX S4 disabled EXP6 S4 disabled PXSX S4 disabled However, the relevant bits seem to be detected from dmesg. [ 0.357628] ACPI: AC Adapter [ACAD] (on-line) [ 0.357749] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 0.357754] ACPI: Power Button [PWRB] [ 0.357817] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1 [ 0.359319] ACPI: Lid Switch [LID0] [ 0.359390] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2 [ 0.359394] ACPI: Sleep Button [SLPB] [ 0.359475] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 0.359479] ACPI: Power Button [PWRF] Not quite sure what to do next.

    Read the article

  • Disabling Keyboard Wakeup for Ubuntu 10.04 on Acer 1810TZ

    - by sybreon
    My Acer Aspire 1810TZ laptop suspends fine but wakes up on any slight key-press. I would like to disable this behaviour. I read that it involves disabling something in the /proc/acpi/wakeup but SLPB does not seem to be listed at all. root@1810TZ:/etc# cat /proc/acpi/wakeup Device S-state Status Sysfs node UHC0 S3 disabled pci:0000:00:1d.0 UHC1 S3 disabled pci:0000:00:1d.1 UHC2 S3 disabled pci:0000:00:1d.2 UHCR S3 disabled EHC1 S3 disabled pci:0000:00:1d.7 UHC3 S3 disabled pci:0000:00:1a.0 UHC4 S3 disabled UHC5 S3 disabled EHC2 S3 disabled pci:0000:00:1a.7 EXP1 S4 disabled pci:0000:00:1c.0 PXSX S4 disabled pci:0000:01:00.0 EXP2 S4 disabled PXSX S4 disabled EXP3 S4 disabled PXSX S4 disabled EXP4 S4 disabled pci:0000:00:1c.3 PXSX S4 disabled pci:0000:02:00.0 EXP5 S4 disabled PXSX S4 disabled EXP6 S4 disabled PXSX S4 disabled However, the relevant bits seem to be detected from dmesg. [ 0.357628] ACPI: AC Adapter [ACAD] (on-line) [ 0.357749] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 0.357754] ACPI: Power Button [PWRB] [ 0.357817] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1 [ 0.359319] ACPI: Lid Switch [LID0] [ 0.359390] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2 [ 0.359394] ACPI: Sleep Button [SLPB] [ 0.359475] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 0.359479] ACPI: Power Button [PWRF] Not quite sure what to do next.

    Read the article

  • Can Current Backflow from Powered Hub's Adapter & cause PC Damage?

    - by SuperUserMan
    Getting this short: Can current flow from a powered USB hub's power adapter (lying 10 Meter away) back to computer via usb port and cause damage to Computer components like mobo, etc? What should be my concerns? Using a 2 Amp 5V Power adapter to power a 10m Long Active Repeater USB extension cable with 4 port HUB & plugging into PC's Front port, causes PC Chassis fan to keep running (thought slower than regular speed) Front Chassis HDD & power LED to turn on (though bit dim) may be other things which i cant detect/see at chip level, in motherboard?? All this even after PC is shut down (bit scary) More detail (in case still want to read): To run 4 High power (needing 450 mAmps) Wifi Adapters, far away from PC, Bought Active Repeater USB Extension Cable with 4 Ports & power port at far end http://www.ebay.com/itm/33FT-USB-2-0-Male-to-Female-Extension-Cable-Hub-Splitter-Adapter-with-4-USB-Port-/390846115254 Then added a locally bought 2 Amp 240V AC to 5V DC Power Adapter and plugged into USB hub which is a part of & situated at far end of a 10 Meter Active Repeater usb extension cable. Even 4 Wifi Adapters run fine (appear to) using this setup, but running chassis fan, dimly lighted Power & HDD LED, even when PC is switched off is bit scary and surely mean 5V & some current is flowing all though that 10 meter extension cable into my USB port & powering stuff. Can this cause damage? and what should be my concerns. Of course I can't switch off the power adapter (lying 10 meters away from PC) every time I switch off my PC to prevent this.

    Read the article

  • ffmpeg - h264 to xvid creates large file

    - by fatnic
    I'm trying to use ffmpeg to convert a h264/aac video file to an xvid/mp3 file so I can play it in my ultra-cheap media player. At the moment the converted video file is TWICE the size of the original mp4. Is there any way to get a smaller file size without loosing too much quality? Even a drop to -qmin 1 is pretty awful! The command i'm using is ffmpeg -i input.mp4 -vcodec libxvid -sameq -acodec libmp3lame -ab 128k -ac 2 output.avi And the ffmpeg output is Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'input.mp4' Metadata: major_brand : isom minor_version : 1 compatible_brands: isomavc1 Duration: 01:34:27.69, start: 0.000000, bitrate: 1520 kb/s Stream #0.0(und): Video: h264, yuv420p, 720x304 [PAR 1:1 DAR 45:19], 1387 kb/s, 25 fps, 25 tbr, 25k tbn, 50 tbc Stream #0.1(und): Audio: aac, 48000 Hz, stereo, s16, 128 kb/s Output #0, avi, to 'output.avi': Metadata: ISFT : Lavf52.64.2 Stream #0.0(und): Video: mpeg4, yuv420p, 720x304 [PAR 1:1 DAR 45:19], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1(und): Audio: libmp3lame, 48000 Hz, stereo, s16, 128 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1

    Read the article

  • Strange battery behavior on laptop

    - by EpsilonVector
    My laptop is behaving rather strangely lately, and I was hoping to get some idea as to what may be causing such symptoms. The problem: When charging, very minute or so it loses connectivity with the AC adapter for a split second, and regains it back immediately. When this happens the little light that indicates the computer is plugged in does flicker off and back on, but I checked the adapter by replacing the battery on my laptop, and this indeed solves the problem, so it is probably the battery which is at fault, not the adapter (I also tried to move the adapter's wire around just to make sure it had nothing to do with torn wires). I suppose that the obvious solution is to get a new battery, but as far as battery defects go- this is a rather strange one; it loses connection with the adapter, but still powers the computer, and changing the power setting to a balanced plan (was maximum performance) seem to have solved the problem too. Is there a chance this is not simply the battery, but some kind of other electronic defect? And if not, what can cause it to behave so strangely? PS I tried to recalibrate it- didn't help.

    Read the article

  • What are the frequencies of current in computers' external peripheral cables and internal buses?

    - by Tim
    From Wikipedia, three different cases of current frequency are discussed along with the types of cables that are suitable for them: An Extra Ordinary electrical cables suffice to carry low frequency AC, such as mains power, which reverses direction 100 to 120 times per second (cycling 50 to 60 times per second). However, they cannot be used to carry currents in the radio frequency range or higher, which reverse direction millions to billions of times per second, because the energy tends to radiate off the cable as radio waves, causing power losses. Radio frequency currents also tend to reflect from discontinuities in the cable such as connectors, and travel back down the cable toward the source. These reflections act as bottlenecks, preventing the power from reaching the destination. Transmission lines use specialized construction such as precise conductor dimensions and spacing, and impedance matching, to carry electromagnetic signals with minimal reflections and power losses. Types of transmission line include ladder line, coaxial cable, dielectric slabs, stripline, optical fiber, and waveguides. The higher the frequency, the shorter are the waves in a transmission medium. Transmission lines must be used when the frequency is high enough that the wavelength of the waves begins to approach the length of the cable used. To conduct energy at frequencies above the radio range, such as millimeter waves, infrared, and light, the waves become much smaller than the dimensions of the structures used to guide them, so transmission line techniques become inadequate and the methods of optics are used. I wonder what the frequencies are for the currents in computers' external peripheral cables, such as Ethernet cable, USB cable, and in computers' internal buses? Are the cables also made specially for the frequencies? Thanks!

    Read the article

  • FFmpeg convert video w/ dropped frames, out of sync

    - by preahkumpii
    I recorded a video using Bandicam with the MJPEG encoder to get the least amount of lag. Now, I am trying to convert that massive file to a h264 avi using ffmpeg. I know there are dropped frames in the video stream...more than 100 in the first two minutes, which I assume is simply because Bandicam dropped some when it couldn't keep up. So, when I convert the file to h264, the video and audio are out of sync, and appear to be more and more out of sync as output video progresses. Here is my basic command in ffmpeg: ffmpeg -i "C:\...\input.avi" -vcodec libx264 -q 5 -acodec libmp3lame -ar 44100 -ac 2 -b:a 128k "C:\...\output.avi" I have tried EVERYTHING I can think of including: -itsoffset [-]00:00:01 Tried this before and after input file. This doesn't work because as the video progresses it becomes more and more out of sync. -async 1 Doesn't work. -vsync 1 Doesn't work, but it does show dropped frames being duplicated. Two inputs of same file with mapping using -map 0:0 -map 1:1. Doesn't work. The source plays just fine. Any ideas how to convert it with ffmpeg and keep the audio and video synced? Thanks.

    Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >