Search Results

Search found 26086 results on 1044 pages for 'site to site vpn'.

Page 29/1044 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• Juniper SSL-VPN Application Data encoding

  - by bong0

  Hi, I want to know how the request & response from the VPN server on e.g.: https://host.tld/dana/jw?con=1234567890&seqno=7 is encoded, the output seems to be binary. I assume it is the application data which gets exchanged with this request, am I right in this? If not, what else gets transferred over this, what is contained in the response? I'm pretty new to this product and want to understand how it works in deep. Thanks in advance folks.

  Read the article

• DD-WRT VPN error 800?

  - by MrZombie

  I have set up a router with DD-WRT Mega on my Asus WL-500gP V2, and I can't connect to the VPN service. I have set it up according to the configuration on the DD-WRT wiki, so the server IP is set to 192.168.1.1, which is the address of the router, and I set up the client addresses to be 192.168.1.20-29. My chap secrets are set up correctly, and still, I get an error 800 on windows XP. As far as I can tell, it means my network is unreachable. The server responds to ping.

  Read the article

• Problems with SCP stalling during file copy over VPN

  - by MattC

  I have a series of files I need to copy via SCP over a VPN to a remote linux server each night. The files are not large, we're talking about tens of megabytes here, but the file copy almost always stalls after a few seconds. Running the SCP command with -vvv, I see the following over and over throughout the attempted copy process: debug2: channel 0: rcvd adjust 131072 debug2: channel 0: rcvd adjust 131072 debug2: channel 0: rcvd adjust 131072 Any thoughts? I see this question being asked in various places out there, but never any answers. Any help would be appreciated.

  Read the article

• Using Ubuntu Karmic as an L2TP Client for VPN

  - by James Lawrie

  I'm trying to connect to a VPN service over L2TP using Karmic as a client and it's not working. The only details I have are the remote IP address, username & password, and a shared secret string; this is enough for Windows but doesn't appear to be enough for Ubuntu. I've tried using network-manager-vpnc and vpnc from the terminal to connect and I get "no supported authentication", and trying with OpenSwan it says "unable to identify either side of the connection". I'd really appreciate some help here if anyone else has implemented this successfully.

  Read the article

• SonicOS Enhanced 5.8.1.2 L2TP VPN Authentication Failed

  - by Dean A. Vassallo

  I have a SonicWall TZ 215 running SonicOS Enhanced 5.8.1.2-6o. I have configured the L2TP VPN using the default crypto suite ESP: 3DES/HMAC SHA1 (IKE). Proposals are as such: IKE (Phase 1) Proposal DH Group: Group 2 Encryption: 3DES Authentication: SHA1 Life Time (seconds): 28800 Ipsec (Phase 2) Proposal Protocol: ESP Encryption: 3DES Authentication: SHA1 Enable Perfect Forward Secrecy DISABLED Life Time (seconds): 28800 When attempting to connect via my Mac OS X client I get an authentication error. It appears to pass the pre-authentication but fails to complete. I am at a complete loss. I reconfigured from scratch multiple times...used simple usernames and passwords to verify this wasn't a miskeyed password issue. I have Here are the logs (noted IP has been removed for privacy): 7/1/13 8:19:05.174 PM pppd[1268]: setup_security_context server port: 0x1503 7/1/13 8:19:05.190 PM pppd[1268]: publish_entry SCDSet() failed: Success! 7/1/13 8:19:05.191 PM pppd[1268]: publish_entry SCDSet() failed: Success! 7/1/13 8:19:05.191 PM pppd[1268]: pppd 2.4.2 (Apple version 727.1.1) started by dean, uid 501 7/1/13 8:19:05.192 PM pppd[1268]: L2TP connecting to server ‘0.0.0.0’ (0.0.0.0)... 7/1/13 8:19:05.193 PM pppd[1268]: IPSec connection started 7/1/13 8:19:05.208 PM racoon[1269]: accepted connection on vpn control socket. 7/1/13 8:19:05.209 PM racoon[1269]: Connecting. 7/1/13 8:19:05.209 PM racoon[1269]: IPSec Phase 1 started (Initiated by me). 7/1/13 8:19:05.209 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). 7/1/13 8:19:05.209 PM racoon[1269]: >>>>> phase change status = Phase 1 started by us 7/1/13 8:19:05.231 PM racoon[1269]: >>>>> phase change status = Phase 1 started by peer 7/1/13 8:19:05.231 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 2). 7/1/13 8:19:05.234 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). 7/1/13 8:19:05.293 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 4). 7/1/13 8:19:05.295 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). 7/1/13 8:19:05.315 PM racoon[1269]: IKEv1 Phase 1 AUTH: success. (Initiator, Main-Mode Message 6). 7/1/13 8:19:05.315 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 6). 7/1/13 8:19:05.315 PM racoon[1269]: IKEv1 Phase 1 Initiator: success. (Initiator, Main-Mode). 7/1/13 8:19:05.315 PM racoon[1269]: IPSec Phase 1 established (Initiated by me). 7/1/13 8:19:06.307 PM racoon[1269]: IPSec Phase 2 started (Initiated by me). 7/1/13 8:19:06.307 PM racoon[1269]: >>>>> phase change status = Phase 2 started 7/1/13 8:19:06.308 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). 7/1/13 8:19:06.332 PM racoon[1269]: attribute has been modified. 7/1/13 8:19:06.332 PM racoon[1269]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). 7/1/13 8:19:06.332 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). 7/1/13 8:19:06.333 PM racoon[1269]: IKEv1 Phase 2 Initiator: success. (Initiator, Quick-Mode). 7/1/13 8:19:06.333 PM racoon[1269]: IPSec Phase 2 established (Initiated by me). 7/1/13 8:19:06.333 PM racoon[1269]: >>>>> phase change status = Phase 2 established 7/1/13 8:19:06.333 PM pppd[1268]: IPSec connection established 7/1/13 8:19:07.145 PM pppd[1268]: L2TP connection established. 7/1/13 8:19:07.000 PM kernel[0]: ppp0: is now delegating en0 (type 0x6, family 2, sub-family 3) 7/1/13 8:19:07.146 PM pppd[1268]: Connect: ppp0 <--> socket[34:18] 7/1/13 8:19:08.709 PM pppd[1268]: MS-CHAPv2 mutual authentication failed. 7/1/13 8:19:08.710 PM pppd[1268]: Connection terminated. 7/1/13 8:19:08.710 PM pppd[1268]: L2TP disconnecting... 7/1/13 8:19:08.711 PM pppd[1268]: L2TP disconnected 7/1/13 8:19:08.711 PM racoon[1269]: IPSec disconnecting from server 0.0.0.0 7/1/13 8:19:08.711 PM racoon[1269]: IKE Packet: transmit success. (Information message). 7/1/13 8:19:08.712 PM racoon[1269]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). 7/1/13 8:19:08.712 PM racoon[1269]: IKE Packet: transmit success. (Information message). 7/1/13 8:19:08.712 PM racoon[1269]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). 7/1/13 8:19:08.713 PM racoon[1269]: glob found no matches for path "/var/run/racoon/*.conf" 7/1/13 8:19:08.714 PM racoon[1269]: pfkey DELETE failed: No such file or directory

  Read the article

• RDP from domain workstation to non-domain workstation via VPN

  - by SILENT

  I am trying to RDP from a domain computer to a non-domain computer over a VPN. I created a rdp profile for a specified user (for example user name: USERX) with the option to save the password. I am able to establish the connection the first time by entering in the password. However, from that point on, whenever the RDP link is reestablished, it would state that my login details were incorrect and ask me re-type the password for COMP\USERX. Problem is, I don't have a domain called COMP and the password would fail even if reentered. The only way I can reestablish the connection is by choosing the option to login as another user.

  Read the article

• VPN - Remote Desktop Connection

  - by alex

  I've set up a VPN connection to my work network on my home PC - running Windows 7 It connects fine. Once connected, I can ping machines that are on my work network using my home pc, however, if I try to RDP to them, it doesn't connect... It seems to initially connect, It asks me for the logon user / password, and when I set them, and click OK, it gets stuck on a screen saying: "Securing Remote Connection" Eventually it pops up saying "This computer can't connect to the remote computer. Try connecting again. If the problem persists, contact the owner of the remote computer or your network administrator" I know this computer is configured to allow remote connections etc... (and I've tried it with several different machines on the remote network) Any ideas what i've set wrong?

  Read the article

• Cant route VLAN over VPN between Cisco ASA 5505 and Cisco 870

  - by user60984

  We've had an existing VPN between a 5505 and 870 for some time. We've just added VLANs to the network on the 5505 side. We can't seem to figure out how to get devices on the VLANs to communicate with devices on the 870 network which have no VLANs. We're thinking we might have to use a router of sorts to handle the routing before hitting the ASA. We thought PFsense might work well. We've been banging our heads against this thing for 2 days so any immediate help would be great. We're up against a deadline. Thanks!!!

  Read the article

• pfsense multi-site VPN VOIP deployment

  - by sysconfig

  have main office pfsense firewall configured like this: local networks WAN - internet LAN - local network VOIP - IP phones need to connect remote offices (multi-users) and single remote users (from home) use IPSEC or OpenVPN to build "permanent" automatically connecting tunnels from remote location to main location. in remote locations, network will look like this: WAN - internet LAN - local network multiple users VOIP - multiple IP phones in order for the IP phones to work they have to be able to "see" the VOIP network and the VOIP server back at the main office for single remote users ( like from home ) the setup will be similar but only one phone and one computer so questions: best way to tie networks together? IPSEC or OpenVPN can this be setup to automatically connect ? any issues/suggestions with that design/topology ? QoS or issues with running the VOIP traffic over a VPN throughput, quality etc.. obviously depends on remote locations connection to some degree

  Read the article

• pfsense multi-site VPN VOIP deployment

  - by sysconfig

  have main office pfsense firewall configured like this: local networks WAN - internet LAN - local network VOIP - IP phones need to connect remote offices (multi-users) and single remote users (from home) use IPSEC or OpenVPN to build "permanent" automatically connecting tunnels from remote location to main location. in remote locations, network will look like this: WAN - internet LAN - local network multiple users VOIP - multiple IP phones in order for the IP phones to work they have to be able to "see" the VOIP network and the VOIP server back at the main office for single remote users ( like from home ) the setup will be similar but only one phone and one computer so questions: best way to tie networks together? IPSEC or OpenVPN can this be setup to automatically connect ? any issues/suggestions with that design/topology ? QoS or issues with running the VOIP traffic over a VPN throughput, quality etc.. obviously depends on remote locations connection to some degree

  Read the article

• Multiple User VPN

  - by Aaron

  I am looking for a cheap or free solution to be able to connect multiple people via VPN to a host computer. Each person should not be able to see what the others are doing while logged in. Is this possible and if so where do I start my hunt? Aaron Update: I was not sure what server, was just thinking of doing it on say a win7 desktop. Just looking into having 2-3 users have access to a program without each seeing each other. Basically, I know nothing and want to know if this is a possibility for me. lol

  Read the article

• Troubles logging into VPN on Win7 64bit

  - by mike

  Hi, Before I can successfully logon to my company's VPN it runs a small check in the browser to check my current processes. One of the things it checks (among other things) is to see if you have an antivirus running. If you don't, you can't connect and it says please install one with a couple links to some free ones. The issue I'm having is I recently upgraded to Win7 x64 and I haven't been able to get past the "antivirus check" part. Before, I had AVG running and I never had a single problem for years. Now I tried both AVG and Avast and I still get blocked. Does it have something to do with both of these antiviruses running in *32 mode in the processes? Any help or ideas on how to fix this would be awesome. Thanks!

  Read the article

• VPN Network intermittantly fails to provide internet: What could be possible causes

  - by Jake M

  We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

  Read the article

• My IPSec VPN isn't allowing me to connect

  - by jbondhus

  I'm following this guide to create an IPsec VPN on a debian server. I followed all the steps, and it still isn't working. If I try connecting to it, I get an error. I've looked for the logs, but I'm not sure where they would be put, other than /var/logs. I aim to be able to browse the internet from my home connection, and access my home network as if it is my local network (eg. access my home fileserver and printers, and screen share my home computers remotely without a complicated port forwarding setup.

  Read the article

• Setting-up Windows Server 2003 as an L2TP/IPSEC VPN server

  - by andyjohnson

  I'm looking for a pointer to step-by-step instructions for setting-up a Win Server 2003 Std box as a L2TP/IPSEC VPN server. I don't need to use certificates - pre-shared key is sufficient - and the server isn't on a domain. All the sources of information I've found assume a level of sysadmin experience that I don't have - which is why I'm looking for a step-by-step description. I'm a experienced developer, not an IT person, but I have what I'd guess is intermediate level experience of configuring/administering small-scale servers, and have set-up OpenVPN-based VPNs on Windows.

  Read the article

• MacBook not connecting anywhere via VPN

  - by Toby

  I was wondering if someone could help me troubleshoot this issue. I have a handful of VPNs set up on my MacBook (Snow Leopard) which I know are working, but today when I tried to use them I get the following error in all cases: could not find the PPP kernel extension I have not needed to use any VPN for a while but they have worked in the past and there is nothing I can think of that I have changed on this machine. I have looked in System/Library/Extensions and PPP.kext is there which is the file I thought it would be looking for? Any help would be greatly appreciated.

  Read the article

• Using a Raspberry Pi as a VPN?

  - by sudo rm -rf

  So I'm sure many of you have heard of the new Raspberry Pi project. I was looking at messing around with Model B, which has the following relevant specs: Broadcom BCM2835 700MHz ARM1176JZFS processor with FPU and Videocore 4 GPU 256MB RAM Boots from SD card, running the Fedora version of Linux (ARM Version) 10/100 BaseT Ethernet socket USB 2.0 socket So I was curious if it would be possible to create a simple VPN out of this little machine. I do realize that since it's an ARM processor that might mess up quite a few things. Any ideas if this is possible? Just for what it's worth, this would be a personal project so I'm not worried about performance.

  Read the article

• VPN using Zywall

  - by Rune FS

  I've played around with a certificate based VPN (normally I don't do hardware) we've manged to setup the connection and the tunnel between the routers is working correctly. We now need the last step. There's no connection to the computers on the other end. What could we have forgotten? (we're testing with two standard configured Win7 machines) EDIT: Just to clarify the tunnel is working I can ping the router on the other end. I can't access the computers on the other side of that router and vice versa. (It's also possible to access the remotemangement console of the remote router on the LAN IP)

  Read the article

• Nodes inside Cisco VPN. Incoming SSH requests allowed. But can't initiate an outbound SSH.

  - by Douglas Peter

  I've a gateway-to-gateway VPN setup between my Linksys RV042 router and a Cisco VPN. I am able to SSH into any of the machine inside the VPN from my network. But none of the machines inside the VPN can initiate an SSH into my network. It seems they've blocked even all ping requests to my network gateway. This is the requirement: I have scripts that SSH into the machines inside the VPN and run a long mysql query. The query generates an output to a file. The time that these queries take is variable. So I have a loop in my machine that periodically SSHes into the VPN machine and checks if the query has finished, and pulls the generated file using SCP. I need to simplify it thus: The script will run at the machine inside the VPN, and when the query completes, it will SSH into my machine and pushes the generated file. Thanks for any ideas.

  Read the article

• Printing to shared printers across VPN

  - by CYMR0

  I have a program that prints labels at five remote sites. Two sites, aren't working, but the rest are with an identical (as far as I can tell) setup. Using Wireshark, I have determined that the handshaking all goes well, but after the "Open Print File Response" the packet that is sent from the server, doesn't reach the client. But I'm a bit at a loss as to where I go from here. I know the port the packet was sent on (445) isn't being blocked, the RST packet gets sent on the same port and that gets there fine. It's also weird that the three out of five sites are working fine. This has been up and running for years without issue, all that we have changed is our connectivity (from DSL to bonded DSL). But this traffic is over a VPN - so it can't be the ISP interfering either can it? I'm totally stuck, and any help would be much appreciated. Thanks!

  Read the article

• How do I learn IPSec VPN implementation on FreeBSD from pfSense

  - by Lang Hai

  I've been trying to figure out a complete working solution for IPSec VPN implementation on FreeBSD but with no luck till now. pfSense seems did a fantastic job on supporting IPSec and even for mobile clients, so I downloaded and installed pfSense hoping to figure out how it works, or at least see some configuration examples, but I couldn't find anything interesting maybe because I'm not familiar with pfSense, so I'd like to ask for help. How pfSense implements IPSec, what tools are used? Where does pfSense store all its configuration files? And since pfSense has its own kernel mods and acts as a different OS, there's no way for us to install it on top of an existing FreeBSD box, and plus that it is such a great project combining those fantastic features, so my question can kinda be extended as: How do we learn from pfSense, and implement its features on top of a regular FreeBSD server?

  Read the article

• Unable to connect to a remote SQL Server Instance over a VPN

  - by Jack Njiri

  I'm running SQL Server 2005 on two different servers running Win XP. The two servers are in different physical locations and are connected via a dedecated point to point data link in a virtual private network(VPN). Im only able to connect to the remote instance of SQL Server by specifying the IP address on the server name property. If I provide the actual server name say 'ServerA', then I get an error message. Everything works fine except configuring replication at the subscriber level, which requires the actual name of the instance, not an IP address or alias. I have already configured both instances on allow remote connections and im running the SQL Server Browser. How do I connect to the remote instance by providing the instance name? Alternatively how I configure subscription to a remote publisher without supplying the remote instance name?

  Read the article

• DELL DRAC & Ubuntu VPN Connection

  - by Mikunos

  I am trying to connect to a DELL DRAC card without success by Ubuntu VPN Connection Manager. I have these data: Protocol: PPTP SERVER IP PPTP: 1233.123.123.123 DRAC IP: 192.168.10.25 Subnet: 255.255.0.0 User: myuser Pass: mypass where have I to write these parameters? I have configured the PPTP connection using the graphical tool in Ubuntu 11.10 ... but in the /var/log/syslog I get these messages: Apr 15 11:33:15 shinet NetworkManager[1035]: <info> Starting VPN service 'pptp'... Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 18180 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' appeared; activating connections Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN plugin state changed: 3 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN connection 'Connessione VPN 1' (Connect) reply received. Apr 15 11:33:15 shinet pppd[18182]: Plugin /usr/lib/pppd/2.4.5/nm-pptp-pppd-plugin.so loaded. Apr 15 11:33:15 shinet pppd[18182]: pppd 2.4.5 started by root, uid 0 Apr 15 11:33:15 shinet pppd[18182]: Using interface ppp0 Apr 15 11:33:15 shinet pppd[18182]: Connect: ppp0 <--> /dev/pts/1 Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. Apr 15 11:33:15 shinet pptp[18185]: nm-pptp-service-18180 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Apr 15 11:33:46 shinet pppd[18182]: LCP: timeout sending Config-Requests Apr 15 11:33:46 shinet pppd[18182]: Connection terminated. Apr 15 11:33:46 shinet avahi-daemon[1081]: Withdrawing workstation service for ppp0. Apr 15 11:33:46 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:46 shinet pppd[18182]: Modem hangup Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet pppd[18182]: Exit. Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state changed: 6 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state change reason: 0 Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active. Apr 15 11:33:51 shinet NetworkManager[1035]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Apr 15 11:33:57 shinet NetworkManager[1035]: <info> VPN service 'pptp' disappeared Thanks

  Read the article

• Connecting PPTP VPN with Ubuntu 9.10

  - by Christian P.

  I have an ubuntu machine that I wish to connect to a VPN and have traffic routed through that. So far I have installed the pptp-linux package and tried my hand at configuring it manually as well as using pptpsetup. I am using Ubuntu 9.10, but regardless of the method I get "Couldn't find MPPE kernel support". Searching a bit for the problem seems to reveal that Ubuntu DOES come with MPPE kernel support (and has done for quite some time). If anyone can figure this out, you'd be a real lifesaver!

  Read the article

• Small business VPN solution

  - by Crash893

  I've been looking for a while but I'd like to to implement a vpn solution for anywhere from 1-5 employees at a time (possibly 10 in a year or so) edit: Basically I would like outside users to fire up a client or open a web page and be able to access things inside the company network (share drives / printers/ webapps /etc) I've looked at Astaro Gateway but im not sure if that's the right tool for the job. I know "best" is a subjective term so i would like to break it into to different suggestions 1) what is the cheapest solution given the criteria above 2) what solution will result in the least amount of headaches from the point of view of maintenance and learning curve.

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >