Search Results

Search found 7024 results on 281 pages for 'usb modem'.

Page 29/281 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• Linux USB debug connection to LuminaryMicro evaluation board

  - by mikelong

  Hi, I am trying to connect a Stellaris LM3S8962 evaluation kit to a linux host machine. I am using the CodeSourcery G++ for the development toolchain. When I try to run a helloworld example the connection fails with this message: arm-stellaris-eabi-sprite: error: E104. I/O Error communicating with USB Device. arm-stellaris-eabi-sprite: waiting for GDB connection, to pass error along warning: Remote failure reply: E.fatal.E104. I/O Error communicating with USB Device. arm-stellaris-eabi-sprite: error: E002. Not initialized When I connect the evaluation board with the USB cable it seems the device is made available to the system: Mar 24 14:37:16 n6-ws2 kernel: usb 5-2: USB disconnect, address 5 Mar 24 14:37:18 n6-ws2 kernel: usb 5-2: new full speed USB device using uhci_hcd and address 6 Mar 24 14:37:19 n6-ws2 kernel: usb 5-2: configuration #1 chosen from 1 choice Also, it seems that I can connect in some way via the command line tool (but I do get some strange characters): [mlong@n6-ws2 bin]$ ./arm-stellaris-eabi-sprite -i CodeSourcery ARM Debug Sprite (Sourcery G++ 4.4-104) armusb: [speed=] ARMUSB device armusb:///?? - ?? (??) Does anyone have any suggestions I could try? Thanks a lot, Mike

  Read the article

• Opening and Testing Ports on Modem > Router Connection

  - by JakeTheSnake

  Working off of my last question, I can access my server's FTP over the LAN but not over the internet. I'm using Filezilla on port 666. My router/modem configuration is as such (similar to other post): 1) Modem connects to WAN 2) WAN port on modem connects to LAN port on Router 3) Modem internal IP address is 192.168.0.254 4) Router internal IP address is 192.168.0.1 5) Modem has DHCP turned OFF 6) Router has DHCP turned ON 7) Router is running Tomato firmware and it's set as 'Router' (not 'Gateway') 8) The internet is working (just had to say that) I've set up port forwarding both on the modem and router - both route port 666 to the IP address of 192.168.0.3 (TCP); that is the IP address of the server which has FileZilla running. I don't know if that's hindering anything but I've also tried it with just the modem and just the router...same result. I've also tried setting the server to be DMZ (both on router and modem). Neither router nor modem have anything in their logs about denying inbound traffic on port 666 so my ability to troubleshoot stops there. I've tried contacting my ISP (Telus, running on mobility plan...it's a "Smart" Hub) but they weren't much help. They said they only block port 25 and 80 and maybe a few others, but not most ports. I test whether or not the port is open by going to canyouseeme.org - I don't know whether or not that would produce a 'connection refused' result just based on the fact that the FTP requires a login...I'm not well versed on this matter. FWIW, sometimes I get a 'connection refused' error on canyouseeme.org but mostly it's 'connection timed out'. I don't know what else to do at this point.

  Read the article

• Does Huawei E398 LTE Modem works with Netgear Router?

  - by Paul Smith

  I've been using a Netgear router sharing the signal through my Huawei E160 dongle, but following the speeds update and the device limit, it does not satisfy the demand. Through research, I've found that Huawei E398 is the latest and functional dongle so far. I'm going to update, but the confusion comes: Is it compatible for my Netgear router? Will it work? Any information will be appreciated. I found the unlocked E398 here.

  Read the article

• How do I create a LiveUSB that lets me install any Ubuntu version?

  - by Dariopnc

  What I'd like to do: have Ubuntu installed on a USB drive and from there install any ubuntu version on a hdd. This is kinda different from using usb-creator because I'd like to have a persistent ubuntu install on the USB drive and not upgrade it every 6 months. From there I'd like to be able to install the most recent ubuntu version. I think it's just a matter of configuring ubiquity, but don't know if this is the case and how exactly do this. EDIT: Let's clarify the persistent thing: suppose I have my USB with ubuntu precise on it suppose quantal is out in the wild suppose that I want to install quantal on the hdd of a computer suppose that I want/can use only the USB drive with precise on it I should erase/upgrade precise on the USB drive to quantal and then install it on the hard drive I don't want to touch my ubuntu install on the USB drive, I'd like to be able to install the newer ubuntu version (quantal) on a hdd from another one (precise) on a USB drive I'd better avoid upgrading the installation on the hdd Hope this helps

  Read the article

• Wireless USB keyboard and mouse can wake system, but then receiver is inactive

  - by BlueMonkMN

  I have a Microsoft brand USB device that acts as a receiver for a wireless Microsoft Keyboard and a wireless Mouse. When it's operating normally, there are LEDs on the device indicating Caps Lock, Num Lock and Function Lock, of which the latter 2 are usually lit. It is plugged into a Dell Isnpiron 531 with Windows 7 32-bit running on an AMD Athlon 64 X2 Dual Core processor 5000+. When the computer goes to sleep (the power indicator on the main box is flashing), I can wake it by moving the mouse. So far all is good. However, something changed in, I think, the past couple weeks (I suspect due to a Microsoft driver update problem). Before the change, after waking the computer, everything would operate normally as far as I could tell, but now after waking the computer, the receiver has no lights on, and the keyboard and mouse are completely unresponsive (which is odd, considering the mouse woke up the computer). There is a button on the receiver that's supposed to reset the wireless connection and flash the lights while it does so, but it has no effect in this state. It's like the receiver doesn't have power (but how would the system know I moved the mouse, unless the power was on until it woke up?). I have checked the BIOS/CMOS settings or whatever you call them, and did not see anything related to USB in the power management section. I have checked Windows 7 device manager and ensured that all the USB Root Hub devices have the setting unchecked for allowing the USB power to be turned off. Like I said, this was working before, and the only thing I can think of that's changed is applying Windows Updates.

  Read the article

• Windows 7 64bits installation via USB asks for drivers

  - by Shikiryu

  I just bought a new config ( ASUS p8z68-v lx, i5-2500k + ram and new graphic card ). Coming back and installing it in my old computer, I just saw that my DVD player was on IDE (yup…). So, I needed to install windows 7 64bits from my usb key. Fine, I made my usb key bootable and copy the official DVD on it (the same version that was on my old computer), set BIOS to boot on it first and started the computer up. It worked fine until it asks me for cd/dvd drivers (which is funny since, I do it via USB because I can't plug in my DVD player :D) I have 3 SATA HDD plugged in and that's it. I made a small google search and found that it could be SATA or RAID drivers. Fine, I took another USB KEY and put all my motherboard drivers on it (from the CD sold with the MB) and none of those drivers seemed to work. I tried downloading new drivers from ASUS website and same effect. Any idea but no "buy a new DVD player", I'm now broke for the month :) ?

  Read the article

• I have a password protected USB drive with hidden partition, how to convert to normal USB drive?

  - by deddebme

  I have a generic USB drive which has password protection, and I want to stop this password protection mechanism and to use it as a normal 8GB USB drive. I received this USB drive as a gift in Hong Kong, and there was no instruction menu whatsoever, not even the manufacturer name. When I plug the drive in Windows XP, the removable drive comes up as a read only 5.28MB partition with two files. When I try to add or remove any files or formatting it, it will says the drive is write protected. After launching the Login.exe and typed in the password, a 8GB read/writeable partition will be shown, and I'm free to do anything to it. But once after the drive is unplugged and replugged, the same read only partition will still comes out no matter what I did to the hidden partition. Anyone knows about this kind if USB drive? What did the manufacturer do to hide the partition? Is there a way to "low-level" formatting this drive to convert (or revert) it to a normal drive? Before typing in the password: After typing in the password:

  Read the article

• Toshiba Satellite P755D USB 3.0 Drivers Missing - Windows 7 Professional

  - by nicorellius

  I bought a Toshiba Satellite P755D recently and installed Windows 7 Professional on the machine. It runs great. But I noticed the exclamation point in the yellow triangle icon in the Device Manager next to the Universal Serial Buss (USB) Controller (I'm assuming this is the USB 3.0 controller because mine doesn't recognize devices). Normally, when this kind of thing happens I go to the manufacturer's website and download appropriate drivers and call it a day. But not this time... I browsed to my model and found no driver for the USB 3.0 controller. I tried other HW and Utility drivers, thinking they would be bundled. No luck. I tried looking up the motherboard in my machine. Generic name, no luck. I then called Toshiba technical support and they tried basic troubleshooting, eg, uninstall device, reboot, for auto-installation; no luck. I popped the Windows 7 disk back in and tried to get information that way, no luck. Finally, the technical support guy said he would look into the engineer's system to see if there was a specific driver available and that's where I'm at. The technician told me that these USB 3.0 drivers come within the native driver pack in windows but that doesn't seem to be the case. Any ideas? EDIT - See attached screen shots.

  Read the article

• USB question (how durable is it, how should I workaround this)

  - by Shiki

  The plot is quite simple. Got a Razer mouse. If I plug it in, it works. After a shutdown/hibernation, I have to replug it entirely at the back of the PC. (It works in my laptop even after severel shutdown, etc, so yes I guess it's my motherboard.. but it still got 2 years of warranty and it comes with quad SLI, its not an old motherboard at all. (MSI P7N SLI FI (bought it after a hungarian guy's recommendation)). So. I only could come up with one "solution". Get 3 USB cable (you know, USB-USB). If its possible the shortest ones (don't know if the responsibility/anything will worsen), AND replug only the middle+closest to the USB port junction, since those are replaceable. What do you think? Any other idea? (BIOS is updated, mouse driver ... doesn't really matter, the mouse won't even blink a bit after this happens. It lights up and goes totally dead.)

  Read the article

• USB transfer speed for Windows 7 is incredibly slow to my external drive

  - by Wolfram

  I'm running Windows 7 Pro and am try to backup 116 GB of data to my external 1 TB hard drive. My laptop has only USB 2.0 ports and my hard drive is USB 3.0 compatible, as is the cable I'm using. I understand that the transfer speed should still be in accordance with USB 2.0 speeds. However, right now I'm getting 135 KB/s and it's been gradually dropping. For an earlier transfer, I would get between 4 MB/s to 8 MB/s. So, I'm really just wondering what's going on with my transfer rate and what I can do to improve it. I'm currently about 35 GB into the 116 GB transfer. Another strange thing is that the window which shows the transfer status decided to max out at 835 MB, and therefore shows items remaining as 0. However, it is still performing the rest of the transfer, and I can see it still cycling through files. Now that I think about it, it seems plausible that the speed being shown by the window is calculated merely as total data transferred / time elapsed. Since the "counter" of data, as far as what is being displayed in the window, maxed out at 835 MB, as time increases, the speed shown is going to keep decreasing because the 'total data transferred' value isn't being incremented. So with that in mind, I suppose I don't actually know at what rate the data is being transferred currently. Nonetheless, my best speed earlier was only around 8 MB/s. Shouldn't USB 2.0 deliver closer to 35 MB/s? Also, if someone can tell me why the transfer status window is displaying the incorrect data information and how to fix this, that would also be appreciated.

  Read the article

• Problem with ubuntu 10.10 running from USB drive

  - by Surjya Narayana Padhi

  I recently downloaded Ubuntu 10.10 and created an USB drive with that. I started to run the Ubuntu from that USB drive. But I am facing so much problem. I am thinking why its not so much easy like Windows to do all my job in ubuntu. Always I get some error message or to install something. This time I am getting the following errors. I am trying to download and install Aircrack-ng. So used the command sudo apt-get install aircrack-ng. But the installation stops with the following error : update-initramfs: deferring update (trigger activated) cp: cannot stat `/vmlinuz': No such file or directory dpkg: error processing bcmwl-kernel-source (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: initramfs-tools bcmwl-kernel-source E: Sub-process /usr/bin/dpkg returned an error code (1) I don't even have the aptitude command installed till now. Are all these errors because of I am running the ubuntu from USB drive? Is there any simple and easy way to go to Ubuntu Software Center and download all the required essentials at one shot and then Aircrack-ng? I could not find the Aircrack-ng in Ubuntu Software Center Can anybody give me detail steps to solve all my problems above. I am frustrated searching for updates and installations. When something works and something does not work. Can anybody suggest me how I should proceed after installing ubuntu to run on a USB drive. So that I can use the OS like Windows. Like software download,wireless driver, sound, video, documents, C:, D: all things should be there. Please somebody help.

  Read the article

• Problem with ubuntu 10.10 running from USB drive

  - by Surjya Narayana Padhi

  Hi Geeks, I recently downloaded Ubuntu 10.10 and created an USB drive with that. I started to run the Ubuntu from that USB drive. But I am facing so much problem. I am thinking why its not so much easy like Windows to do all my job in ubuntu. Always I get some error message or to install something. This time I am getting the following errors. I am trying to download and install Aircrack-ng. So used the command sudo apt-get install aircrack-ng. But the installation stops with the following error : update-initramfs: deferring update (trigger activated) cp: cannot stat `/vmlinuz': No such file or directory dpkg: error processing bcmwl-kernel-source (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: initramfs-tools bcmwl-kernel-source E: Sub-process /usr/bin/dpkg returned an error code (1) I don't even have the aptitude command installed till now. Are all these errors because of I am running the ubuntu from USB drive? Is there any simple and easy way to go to Ubuntu Software Center and download all the required essentials at one shot and then Aircrack-ng? I could not find the Aircrack-ng in Ubuntu Software Center Can anybody give me detail steps to solve all my problems above. I am frustrated searching for updates and installations. When something works and something does not work. Can anybody suggest me how I should proceed after installing ubuntu to run on a USB drive. So that I can use the OS like Windows. Like software download,wireless driver, sound, video, documents, C:, D: all things should be there. Please somebody help.

  Read the article

• USB-to-Serial showing gibberish at 115200 Baud

  - by Mose

  I've got a serious problem which drives me crazy because I tried everything I could think of. First of all, I made a video: http://youtu.be/boghkuq7L_s but please read the following text for more information, not only view the video! When using a USB-to-Serial interface everything works as long as I don't go beyond 57600 Baud. At higher rates I only get giberish like this: év.­b0JNLYÆÿ¿iëd0U²(kßÞb! ú]/xscB!ï¯!BoXûÿ1ïâÖCÿ6ÌAnè*íÌC)º¿BíÞØ.C.@ÆÃwHJÂs "YE:ñ.èFðÌCÊ÷ÞÄ !x H w6@BtbHJ ̪ Ì6ì H¾a¿bH.">îvy®;f<ßBÌ p­L¨fæH­E ­þ¼MBÞI What makes the problem so strange is, I exchanged every component and the problem still presists. I tried differtent OSes (Ubuntu, WinXP, Win7, OSX 10.7) with 32 and 64 Bit. I tried USB-to-Serial interface from FTDI and Prolific. I tried reading the output from my Raspberry PI and from an Asterisk Appliance. I changed the cables and the wiring. Nothing helped. In the video I made a example with a old Notebook with native COM and put the USB-to-Serial to the same connection as "sniffer" (only Rx and GND connected) to make sure the output and everything is ok as one can see on the native port. The voltage is ok. Settings for both are 115200 Baud, 8 Bit with 1 Stop and no flow control. Native is ok. USB is messed up. I used the newest drivers and double checked all connections. I have no idea what is wrong here. As I couldn't find anyone describing problems like this I question my long experiance in computer science and think I'm doing some completly wrong... Please help :-/

  Read the article

• HD working with IDE USB adapter but not recognised by bios

  - by Rajeeva

  I have a Windows XP Pentium III desktop with two hard drives. The first one has the OS and is luckily working. The second drive on the secondary master IDE channel few days back was unable to read some files and since then for some time it was failing and reviving intermittently and now it is always showing as failed on the IDE channel When the HD was intermittenly failing, I was able to copy some data from it to the other drive - also during that time if the system was running and the hard disk failed at that time, the system froze and then i had to reboot. then I got a new 80 gb hdd similar (same make - seagate barracuda) to the earlier failing one, a new data cable for the drive and an IDE to USB adapter. the new hard drive i installed in the previous drive's place (secondary master), formatted it and it worked for 1 day and then it also failed - simultaneously i connected the old hd to the IDE/USB adapter and i could view all the data - some of that data i was able to back up from the old hd to the new hd before the new hd failed the new hd i have tried connecting on the primary channel as the slave disk but when i do that then the bios does not detect either the OS drive or the new drive and the system does not boot surprisingly, the older (previously failed) hd and the new hd are both working fine on the usb channel with the IDE/USB adapter. i have ruled out any problem with the secondary channel since the dvd rom i was earlier using as primary slave have now connected to secondary master and it works fine. i am really confused by this behavior on my system. please can anybody try to solve this for me. thanks.

  Read the article

• Is it possible connect USB DRIVE to iPhone (using data cable and EAAccessory) ?

  - by Sergey

  Hello, all! Is it possible connect USB FLASH DRIVE to iPhone cable and onIphone reading data from this drive ? thanks,

  Read the article

• iPhone tethering via USB not working

  - by arneevertsson

  I can't get USB tethering to work. My setup: iMac with Mac OS 10.6.2 iPhone 3G, Sofware version 3.1.2 (Build 7D11) The phone shows up in iTunes and syncing works as it should. I went to System Preferences / Network and added the iPhone as a Network Service. To the right there is a status message for the selected service. With the iPhone not plugged in, the status message reads: Either the cable for iPhone is not plugged in or the device is not responding. With the iPhone plugged in, the status message reads: Either the cable for iPhone USB is not plugged in or the device is not responding. Almost identical messages, the only difference is "USB". Any clues?

  Read the article

• System Rescue CD on multiboot usb not working

  - by darkfeline

  I have a multiboot usb with System Rescue CD and GRUB2 on it. When I try to boot it, it tries to find systemrescuecd/sysrcd.dat, attempts to mount /dev/sr0 and all the partitions on /dev/sda before declaring cannot find systemrescuecd/sysrcd.dat on devices and dumping me onto a primitive shell. The relevant entries in grub.cfg: menuentry "SystemRescueCd 32bit" { linux /systemrescuecd/isolinux/rescuecd rootfs=/systemrescuecd subdir=systemrescuecd dostartx setkmap=us initrd /systemrescuecd/isolinux/initram.igz } menuentry "SystemRescueCd 64bit" { linux /systemrescuecd/isolinux/rescue64 rootfs=/systemrescuecd subdir=systemrescuecd dostartx setkmap=us initrd /systemrescuecd/isolinux/initram.igz } I think the problem is that System Rescue CD cannot see /dev/sdb, which is my usb, but I don't know where to begin to fix it. If it helps, I set up my USB with a utility called MultiSystem, which is like MultiISO for Linux.

  Read the article

• Looking for a USB Thumbdrive / Flash drive encryption solution (not TrueCrypt)

  - by Max888

  I am looking for a USB Thumbdrive / Flash drive encryption solution. I have searched the net but I have never come accross a solution which meets the following: Must handle at least 4GB volume If possible, fully portable (no install required required) Does not require admin rights in order to access/write encrypted files on the flash drive Does not corrupt data should the flash drive is removed from a USB port and the data is in a 'unencrypted' status Data is automatically encrypted if the flash drive is removed from a USB port and the data is in a 'unencrypted' status Portable apps must be able to run from the 'unencrypted' volume (in non-admin mode) PLEASE do not mention TrueCrypt as I am not considering (especially for wish list #3) Many thanks! Update 5th October 2009: Still unresolved.

  Read the article

• Mechanical mouse using USB-to-PS/2 Adapter freezes occasionally

  - by izn

  I am using an AOpen PS/2 mechanical mouse in Ubuntu 11.10 with a Staples USB-to-PS/2 Adapter with my Intel DP67DE motherboard. The mouse is more comfortable for my hand as it has a lower height than optical mouses. Occasionally the mouse cursor freezes and often I have to unplug it from the USB port and plug it back in to unfreeze it. This happens with all the USB ports. I've been using the adapter for a few weeks now and this seems to be happening more often recently. What might be happening and is there anything that can be done to fix this?

  Read the article

• WinXP How to Tunnel LPT over USB

  - by Michael Pruitt

  I have a windows program that accesses a device connected to a LPT (1-3) 25 pin port. The communication is bidirectional, and I suspected the control lines are also accessed directly. I would like to migrate the device to a machine that does not have a LPT port. I saw the dos2usb software, but that takes the output (from a DOS program) and 'prints' it formatted for a specific printer. I need a raw LPT connection, and a cable that provides access to all the control signals. I do have a USB to 36-pin Centronics that may have the extra signals. I use it with a vinyl cutter that doesn't like most of the USB dongles. It comes up as USB001. Would adding and sharing a generic printer, then mapping LPT1 to the share get me closer? Would that work for a parallel port scanner? My preferred solution is a USB cable with a driver that will map it to LPT1, LPT2, or LPT3.

  Read the article

• Diagnose Issues with USB External Hard Drive

  - by Chris Lieb

  I have a 1TB SATA hard drive in a third-party USB enclosure hooked up to my computer via USB. The drive has become increasingly unreliable, randomly unmounting and remounting in Windows, making strange noises on occasion, and every once in a while making lots of noise and then unmounting, only fixable by powering down the enclosure, waiting a while, then powering it back up again. I am unsure if the hard drive or the enclosure is to blame. The random unmount/remount could be the enclosure, but the strange sounds are likely related to the hard drive. Given this uncertainty, I want to figure out which of the two items needs to be replaced. However, I do not know of a way to test each item separately since I do not have an extra SATA-to-USB enclosure to test the hard drive with or an extra SATA hard drive to test the enclosure with. Does anyone know how to figure out what's to blame so that I don't have to replace both unless it is absolutely necessary.

  Read the article

• Ubuntu 9.10 desktop installation via USB (boot)

  - by user277980

  I have made a live boot USB using the UnetBootIn tool for Ubuntu 9.10. I have Windows XP SP2 installed as the primary OS, and I want to make a partition for Ubuntu. But when I try to boot it via USB, it just goes to boot menu of Ubuntu, then I enter the default type for installation. After that nothing happens, just the Ubuntu logo shows up and just that nothing happens after that. I can try the simpler task also i.e. install via CD but I want to know what's not working with this USB boot method. Thanks in advance.

  Read the article

• Debian as USB hardware portable as possible

  - by James Mitch

  I have recent hardware, 64 bit, pae and so on. But I'd like to have my Debian installation on a USB HDD. Installing Debian to USB is solved. I used the i386 architecture image. But a pae kernel has been installed. I want to be able to travel with my USB HDD and therefore I want best possible hardware compatibility. My friends and family have sometimes older hardware, but always i386, just sometimes without 64 bit or pae. Never met someone with sparc or other architectures. What should I do to get non-pae kernel and maximum hardware compatibility?

  Read the article

• Create Windows 8.1 USB Boot Disk to Boot in OSX Maverick

  - by Pengan

  After I installed Mac OSX Maverick 10.9 to my Mac Computer. I have a problem with installing Microsoft Windows 8.1 into my Mac my using Bootcamp. I try some third party software such as Win USB Boot Maker and Rufus. These softwares can make USB Boot disk for non Mac computer however they cannot make it work with Mac. Does anyone know how to create a working Windows 8.1 USB Boot Disk to work with Mac computer which run OSX Maverick? Thank You! Pengan

  Read the article

• Windows XP - removing write protection for usb drives

  - by Arnold

  I have a laptop who used to belong to my company and when I plug in a usb memory drive, I cannot write any files to it. This is because company policy did not allow writing to usb drives without a special authorization (to prevent theft of files). However the laptop is now mine, and I was given the administrator password, so I am guessing that as administrator I can remove this protection somehow. How can I do this? Currently if I try to copy a file to the drive, Windows simply tells me that the drive is write-protected, whatever usb drive I plug in. Maybe it is some registry setting? Thank you.

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >