Search Results

Search found 10106 results on 405 pages for 'fail fast'.

Page 291/405 | < Previous Page | 287 288 289 290 291 292 293 294 295 296 297 298  | Next Page >

• mkfs Operation Takes Very Long on Linux Software Raid 5

  - by Elmar Weber

  I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

  Read the article

• Scaling databases with cheap SSD hard drives

  - by Dennis Kashkin

  Hey guys! I hope that many of you are working with high traffic database-driven websites, and chances are that your main scalability issues are in the database. I noticed a couple of things lately: Most large databases require a team of DBAs in order to scale. They constantly struggle with limitations of hard drives and end up with very expensive solutions (SANs or large RAIDs, frequent maintenance windows for defragging and repartitioning, etc.) The actual annual cost of maintaining such databases is in $100K-$1M range which is too steep for me :) Finally, we got several companies like Intel, Samsung, FusionIO, etc. that just started selling extremely fast yet affordable SSD hard drives based on SLC Flash technology. These drives are 100 times faster in random read/writes than the best spinning hard drives on the market (up to 50,000 random writes per second). Their seek time is pretty much zero, so the cost of random I/O is the same as sequential I/O, which is awesome for databases. These SSD drives cost around $10-$20 per gigabyte, and they are relatively small (64GB). So, there seems to be an opportunity to avoid the HUGE costs of scaling databases the traditional way by simply building a big enough RAID 5 array of SSD drives (which would cost only a few thousand dollars). Then we don't care if the database file is fragmented, and we can afford 100 times more disk writes per second without having to spread the database across 100 spindles. . Is anybody else interested in this? I've been testing a few SSD drives and can share my results. If anybody on this site has already solved their I/O bottleneck with SSDs, I would love to hear your war stories! PS. I know that there are plenty of expensive solutions out there that help with scalability, for example the time proven RAM-based SANs. I want to be clear that even $50K is too expensive for my project. I have to find a solution that costs no more than $10K and does not take much time to implement.

  Read the article

• Network connection keeps dropping - bad hardware?

  - by Bill Sambrone

  Hello all, I've into a bit of a wall with a client of mine. In an office of 20 people, he is the only one who experiences broken connections to his mapped network drives. I have everyone set up with about 6 mapped drives, all pointing to the same server (no DFS), and everyone else can access them lightning fast. The environment consists of a mix of Windows 7 and XP machines, all 32-bit. The server holding the data everyone is mapping to is running on Server 2008 R2, and is a domain controller. We recently swapped out their old 10/100 switch for a shiny new Dell PowerConnect gigabit switch. We have also replaced an old dying Sonicwall with a shiny new one. Everything is running on an ESX host except for the DC, where everyone is getting data from. In my client's office, we have done the following: Swapped out his computer (Win7 and XP box) Swapped out the desktop switch in his office Removed the desktop switch in his office Changed out the network cable going to the wall Ran 'net config server /autodisconnect:-1' on the server Disabled remote differential compression on his current Win7 box When we swapped out his network cable, everything seemed fine for about 4 days. Normally I would get a phone call a couple times per day letting me know that Outlook has crashed (there is a 9GB PST living on the server he is always connected to), or that his software he is running from his L drive has crashed. I almost thought I had this solved, but after we rebooted the DC the other night he all of a sudden couldn't stay connected to his mapped network drives for more than 10 minutes. When I ran 'net use' from the command prompt, it listed all the network drives where were randomly in a state of 'OK', 'Disconnected', or 'Reconnecting'. What else should I try? Maybe there is bad wiring in the wall, patch panel, or a bad port in the new switch I have in the server room?

  Read the article

• Heartbeat/DRBD failover didn't work as expected. How do I make the failover more robust?

  - by Quinn Murphy

  I had a scenario where a DRBD-heartbeat set up had a failed node but did not failover. What happened was the primary node had locked up, but didn't go down directly (it was inaccessible via ssh or with the nfs mount, but it could be pinged). The desired behavior would have been to detect this and failover to the secondary node, but it appears that since the primary didn't go full down (there is a dedicated network connection from server to server), heartbeat's detection mechanism didn't pick up on that and therefore didn't failover. Has anyone seen this? Is there something that I need to configure to have more robust cluster failover? DRBD seems to otherwise work fine (had to resync when I rebooted the old primary), but without good failover, it's use is limited. heartbeat 3.0.4 drbd84 RHEL 6.1 We are not using Pacemaker nfs03 is the primary server in this setup, and nfs01 is the secondary. ha.cf # Hearbeat Logging logfacility daemon udpport 694 ucast eth0 192.168.10.47 ucast eth0 192.168.10.42 # Cluster members node nfs01.openair.com node nfs03.openair.com # Hearbeat communication timing. # Sets the triggers and pulse time for swapping over. keepalive 1 warntime 10 deadtime 30 initdead 120 #fail back automatically auto_failback on and here is the haresources file: nfs03.openair.com IPaddr::192.168.10.50/255.255.255.0/eth0 drbddisk::data Filesystem::/dev/drbd0::/data::ext4 nfs nfslock

  Read the article

• Updated my WAMP Server and MySQL is eating up 580mB of memory

  - by Jon

  I updated my dev-box's WAMPSERVER, and along with updating PHP and Apache, MySQL updated to '5.6.12'. After doing that, I copied the data folder from my old (5.1.36) install to the new one and now MySQL takes up 580mB which is way too much, since I'm the only person using it (Locally) and there are only 20 or so databases on it, none of which have 'memory' tables. How can I get this down to a decent amount? My my.ini: # For advice on how to change settings please see # http://dev.mysql.com/doc/refman/5.6/en/server-configuration-defaults.html # *** DO NOT EDIT THIS FILE. It's a template which will be copied to the # *** default location during install, and will be replaced if you # *** upgrade to a newer version of MySQL. [mysqld] # Remove leading # and set to the amount of RAM for the most important data # cache in MySQL. Start at 70% of total RAM for dedicated server, else 10%. # innodb_buffer_pool_size = 128M # Remove leading # to turn on a very important data integrity option: logging # changes to the binary log between backups. # log_bin # These are commonly set, remove the # and set as required. # basedir = ..... # datadir = ..... # port = ..... # server_id = ..... # Remove leading # to set options mainly useful for reporting servers. # The server defaults are faster for transactions and fast SELECTs. # Adjust sizes as needed, experiment to find the optimal values. # join_buffer_size = 128M # sort_buffer_size = 2M # read_rnd_buffer_size = 2M sql_mode=NO_ENGINE_SUBSTITUTION,STRICT_TRANS_TABLES Database info: Storage Engine Data Size Index Size Total Size InnoDB 48.00 KB 0.00 B 48.00 KB MEMORY 0.00 B 0.00 B 0.00 B MyISAM 163.64 MB 122.49 MB 286.13 MB Total 163.69 MB 122.49 MB 286.18 MB

  Read the article

• Standards for documenting/designing infrastructure

  - by Paul

  We have a moderately complex solution for which we need to construct a production environment. There are around a dozen components (and here I'm using a definition of "component" which means "can fail independently of other components" - e.g. an Apache server, a Weblogic web app, an ftp server, an ejabberd server, etc). There are a number of weblogic web apps - and one thing we need to decide is how many weblogic containers to run these web apps in. The system needs to be highly available, and communications in and out of the system are typically secured by SSL Our datacentre team will handle things like VLAN design, racking, server specification and build. So the kinds of decisions we still need to make are: How to map components to physical servers (and weblogic containers) Identify all communication paths, ensure all are either resilient or there's an "upstream" comms path that is resilient, and failover of that depends on all single-points of failure "downstream". Decide where to terminate SSL (on load balancers, or on Apache servers, for instance). My question isn't really about how to make the decisions, but whether there are any standards for documenting (especially in diagrams) the design questions and the design decisions. It seems odd, for instance, that Visio doesn't have a template for something like this - it has templates for more physical layout, and for more logical /software architecture diagrams. So right now I'm using a basic Visio diagram to represent each component, the commms between them with plans to augment this with hostnames, ports, whether each comms link is resilient etc, etc. This all feels like something that must been done many times before. Are there standards for documenting this?

  Read the article

• Using NFS for scalable PHP/MySQL web application

  - by Jeroen Moons

  Here's the situation: I have a PHP/MySQL web application that accepts user uploads (pdf files). From these pdf files' pages a preview image is made on the fly and presented to the web app's users. Some pdfs might be on the large side, most will be under 50 MB but some extreme cases could be as large as a few hundred MB. A little waiting for the preview image for large pdf files is acceptable but no more than a minute let's say. Everything is running on one server for now, but soon the app will hit the server's limit on both storage and processing power. My idea to solve the problem: To deal with this situation I had the idea of having one or more pdf processing servers as needed, and one or more file storage servers. These two types of servers are mounted to the server on which the actual app runs using NFS. The app could then use GearMan to delegate pdf processing tasks to these processing servers. The processing server can mount the storage server and read the file stored there, process it and write its output to that server. The servers I'm talking about will be amazon ec2 instances. The web app returns a link to the resulting pdf preview image on the storage server that was used which can then be used on the front end to show the image to the user. My question: I have zero experience with apps that use multiple servers, is this idea viable or is there a better way to do it? Is an NFS setup fast and reliable enough for this situation?

  Read the article

• MS Excel 2010 - Using DSN + 32 bit drivers

  - by Kristiaan

  I need some advice as im running into a problem and so far i have been unable to find a solution. We have a set of reports developed in MS Excel that use DSN file to connect to data sources to retrieve data, these work fine on 32 / 64bit systems, however we are moving to a terminal server environment using windows 2008 R2 64Bit. The reports fail to run using the DSN's within this environment if we only have the 32bit drivers installed and configured in the ODBC settings, the minute we install the 64Bit drivers the software works. Is there a way / Method of getting Excel or the DSN file to NOT use the 64Bit driver, but force it to use the 32bit driver. ANSWERED - But due to low user score i cannot "answer" my own question... Sadly there is no way to-do what i want to-do, without a lot of very nasty and not 100% perfect reg hacks. If you need to access 32bit ODBC data sources the application in question has to be 32Bit. here is a link to just one forum post i found relating to this type of problem, it appears the only way i would be able to accomplish this is to remove the 64bit version of office and install the 32bit version instead of it. http://social.msdn.microsoft.com/Forums/en-US/accessdev/thread/5108f337-f06a-4518-afe3-d3c1abd040ef/

  Read the article

• Percona-server time out on /etc/init.d/mysql start

  - by geekmenot

  Every time I start mysql, using /etc/init.d/mysql start or service mysql start, it always times out. * Starting MySQL (Percona Server) database server mysqld [fail] However, I can get into mysql. Just wanted to know if there is a problem with the install because it happens all the time, not a one off error. mysql-error.log shows: 121214 11:25:56 mysqld_safe Starting mysqld daemon with databases from /data/mysql/ 121214 11:25:56 [Note] Plugin 'FEDERATED' is disabled. 121214 11:25:56 InnoDB: The InnoDB memory heap is disabled 121214 11:25:56 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121214 11:25:56 InnoDB: Compressed tables use zlib 1.2.3 121214 11:25:56 InnoDB: Using Linux native AIO 121214 11:25:56 InnoDB: Initializing buffer pool, size = 14.0G 121214 11:25:58 InnoDB: Completed initialization of buffer pool 121214 11:26:01 InnoDB: Waiting for the background threads to start 121214 11:26:02 Percona XtraDB (http://www.percona.com) 1.1.8-rel29.2 started; log sequence number 9333955393950 121214 11:26:02 [Note] Server hostname (bind-address): '0.0.0.0'; port: 3306 121214 11:26:02 [Note] - '0.0.0.0' resolves to '0.0.0.0'; 121214 11:26:02 [Note] Server socket created on IP: '0.0.0.0'. 121214 11:26:02 [Note] Slave SQL thread initialized, starting replication in log 'mysql-bin.005163' at position 624540946, relay log '/data/mysql/mysql-relay-bin.000043' position: 624541092 121214 11:26:02 [Note] Slave I/O thread: connected to master '[email protected]:3306',replication started in log 'mysql-bin.005180' at position 823447620 121214 11:26:02 [Note] Event Scheduler: Loaded 0 events 121214 11:26:02 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.5.28-29.2-log' socket: '/data/mysql/mysql.sock' port: 3306 Percona Server (GPL), Release 29.2

  Read the article

• Load is 0, yet site crawls (sometimes). What gives?

  - by Yegor

  I have a ~1.5-2mil page views per day site running on 2 servers. One for mysql, other for everything else. Mysql box has a load of 3, frontend is usually 0.0-0.1. Both are dual quad core with 8GB ram running SAS drives in raid5. CPU is idle for majority of the time, iowait is non-existent. Im running nginx, memcache, and site is built on php. Half the time everything runs perfect, while at other times it lags something severe, when it takes 10-15 seconds for a page to load. Page execution time is always super low, but it seems to hang, waiting for something before it actually loads the page. Whats even more weird is that it only happens to 1 file on the site (but its the one thats most commonly accessed, that actually loads the content on the site). Other pages are super fast at all times, even when it takes 15 seconds to load actual content. I have nginx_stats plugin installed, and if I monitor it, the lag spikes happen when the write column starts going above 100, and it frequently does... all the way to 500-1000. It does so at totally random times... not when traffic is heavy... it can do this in the middle of the night, and work perfectly at 5pm when traffic is at its highest. Any ideas?

  Read the article

• 802.11g -> wired ethernet bridging not working

  - by Malachi

  Usually people want to go the other direction, but I want to take our relatively fast and stable house 802.11g signal and bridge it to ethernet. I have tried using an Airport Express (the b/g flavor) and my i7 MacBook pro, both to no avail. Word is that the b/g flavor of This flavor of Airport Express maxes at firmware 6.3 which doesn't support this kind of bridging properly. However, I expected my MacBook pro to do the job with its "Internet Sharing" feature. Alas, although my wired PC does sort of see it, it doesn't work out. Strangely, using DHCP the PC receives the same IP address as my MBP uses on the network. Less strangely, but still surprisingly, the wired ethernet port on my mac registers as the IP address of the gateway when queried with IFCONFIG. It sort of makes sense that the mac would "pretend" to be the gateway, but the whole thing just isn't working and seems configured wrong - but all the docs I see say basically "OS X Internet Sharing: click it and go". What do I do? Do i really have to buy more hardware, even though I have plenty of would-be candidates for bridging? Incidentally, the host router originating the 802.11g signal is a belkin 802.11g router, and is documented to support WDS.

  Read the article

• Upgrade SQLServer 2008 hardware

  - by John

  Forgive me if I'm not able to be totally clear here. It is not intentional, I'm a senior level developer in a very small company having to act like a manager at the moment. Anyway, the story is that we have 2 older dell servers with SQL Server 2008 Standard in a "cluster". I put that in quotes because I'm still not 100% clear what that means. We have 2 brand new blade servers and want to move the existing databases to the new hardware. Ok, so here is the gotcha. We need to do this with little or no down time. I'm being told that we can evict the passive node, then pull in one of the new servers. But I'm also being told that this is a dangerous step because something could go wrong that would cause the cluster to fail and then we would be left with nothing because the active server would not be able to come back up. Does anyone have any thoughts on how to handle this? I'm being told that the only way to ensure success is to have at least a day of down time where we bring up a new cluster on the new hardware and then migrate the databases 1 by 1.

  Read the article

• Best Practice - SQL 2012 & IIS in VMWare

  - by Dan Ribar

  We are pretty new to VMWare and looking for some thoughts on our environment. We have a VMWare cluster that has on one host: VM#1: MS Windows 2008 R2 Enterprise & SQL Server 2012 VM#2: MS Windows 2008 R2 Standard & IIS The IIS asp.net app talks directly to the SQL Server. We had this similar environment on physical servers a few months ago and just recently moved to the virtualized environment. Regarding the setup, we have not tweaked any of the vm resource parameters -- all is set as standard and all is working. What is observed is that the VMs seem to spool down and we get lags in response. Of course this sin't as fast as the old physical environment, but I am wondering if: *is it a good idea to run the SQL server and the IIS server on the same host? They are the only two VMs on it. The host is a new Dell R620 with 192 gb mem. does it make sense to change any CPU or memory reservations when it doesn't seem like there is any contention is there a way to keep the VMs spooled up to eliminate delays? This is a brand new squeaky clean vanilla install. What are your thoughts?

  Read the article

• Windows 8 x64 with VMWare Workstation or inside ESXi

  - by Dommer

  I need to run several virtual machines on a core i7-920 box with 12GB or RAM and a 256GB SSD to host the VMs. It also has a Highpoint RocketRaid 2720SGL RAID controller with a 12TB RAID 5 array. I want one of my VMs to run Windows 8 x64, to have access to the RAID array as a native disk (not as networked drives and it needs to run at full speed) and to be able to send files quickly across the network. Initially I thought I'd try to do this using ESXi 5, but I have been unable to find any working RAID drivers for the RR2720SGL and it is not on the HCL for ESXi 5. In light of this, I have installed Windows 8 x64 on the hardware and am thinking of installing VMWare Workstation and running my VMs inside there. I guess my questions are these: How does VMWare Workstation 9 perform compared to ESXi 5? In the real world I mean? Presumably installing Win 8 as the host OS will give me way better performance for that Win 8 machine than Win 8 running under ESXi? I should stick with Windows 8 x64 as the host OS, right? If I install a domain controller VM inside my Win 8 box and join the Win 8 machine to that domain, am I insane (I would guess the Win 8 machine wouldn't see the domain controller until it finished starting everything up, but I don't think that matters)?! is it feasible to give metrics like this and if so, what is the likely value of x? 25%? 50%? 75%? Win 8 under ESXi runs x% as fast as Win 8 installed bare metal.

  Read the article

• How do I Forward root's email to an external email address?

  - by ErebusBat

  I have a small server (Ubuntu 10.04) at my house and I would like to forward root's email to my gmail hosted domain to get security notifications and what not. I ripped everything out and started from scratch and ran into some other issues. I now have sendmail working in the sense that I can mail [email protected] and get the mail. HOWEVER, adding an address to /root/.forward does not actually forward the message. I get the following in my logs: Dec 22 14:04:37 batcave sendmail[4695]: oBML4bAT004695: to=<root@batcave>, ctladdr=aburns (1000/1000), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30075, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (oBML4bJ9004696 Message accepted for delivery) Dec 22 14:04:39 batcave sm-mta[4698]: STARTTLS=client, relay=[69.145.248.18], version=TLSv1/SSLv3, verify=FAIL, cipher=DES-CBC3-SHA, bits=168/168 Dec 22 14:04:40 batcave sm-mta[4698]: oBML4bJ9004696: to=<[email protected]>, ctladdr=<[email protected]> (1000/1000), delay=00:00:03, xdelay=00:00:03, mailer=relay, pri=120336, relay=[69.145.248.18] [69.145.248.18], dsn=2.0.0, stat=Sent (OK 01/D4-00853-216621D4) You can see where my local sendmail instance accepts it then hands it off to my ISP, but with the wrong address ([email protected]).

  Read the article

• Zsh super slow inside my Git repo

  - by Jason Swett

  My Zsh is super slow inside a certain Git repo of mine. When I Google "zsh git slow", I get a bunch of results about Git autocompletion being slow, but autocompletion isn't necessarily my problem; it's everything. I tried removing all plugins and that, strangely, didn't do anything at all when I opened a new shell. Zsh would still do Git stuff inside my Git repo. I found this snippet on this page: function git_prompt_info() { ref=$(git symbolic-ref HEAD 2> /dev/null) || return echo "$ZSH_THEME_GIT_PROMPT_PREFIX${ref#refs/heads/}$ZSH_THEME_GIT_PROMPT_SUFFIX" } That made everything fast again, but it also gave me a prompt that looks like this: ? snip git:(master Note the missing right parenthesis. That's kind of lame. Plus the whole thing just seems like a hack I shouldn't have to do. There's also this promising-looking SU question, but the links on the accepted answer are dead. How can I get my Zsh not to be slow inside a Git repo?

  Read the article

• SQL Server becomes slow after restart

  - by Tobi DM

  I already posted this one on stackoverflow but someone gave me the hint to that I might have more luck on serverfault. We use SQL Server 2005 on an Windwos Server 2008. Ther Server has 48 GB RAM. SQL Server is configured to use 40 GB RAM. There is only one database hosted (About 70 GB). The only app beside SQL Server is our App-Server which connects the clients to the database. Now we encounter the following problem: After a restart of the server our the performance is great. The server grabs the 40 GB RAM wich it is allowed to and then runs fast as hell. But after about 4 weeks the system becomes slower and slower. The execution of statements (seen in the profiler) is raising slowly. But I cannot see that there is something going wrong on the server. CPU usage is at about 20% I/O also seems to be no Problem The process monitor does also not show that there are strange apps or something like that. Eventlog does also have no interessting messages No open transactions or blockings to see We do not use cursors in our app We tried already the following things without effect: Droped the cache by using the statements DBCC FreeProcCache DBCC FREESYSTEMCACHE('ALL') DBCC DropCleanbuffers Restarted the Appserver we are using. Restart the sql server service But nothing did help exept restarting the whole server. Any ideas?

  Read the article

• VPN - local and remote networks IP collision

  - by Guido García

  I have created a VPN connection in Windows using the New Network Connection wizard that comes with Windows. It works without problems in most places, but there is one concrete place where, despite the connection to the remote public IP works fine, it is not able to validate the login/password and establish the VPN connection. In this place, the network is 10.0.0.x (the same I use in other places where I am able to connect). The remote network is 192.168.x.x, so I suspect there is some kind of IP collision, because before connecting, a traceroute to i.e. 192.168.0.40 does not fail. 1 4 ms 1 ms 1 ms LINKSYS [10.0.0.1] 2 5 ms 1 ms 1 ms 172.26.27.1 3 4 ms 5 ms 3 ms 192.168.1.100 ... (more) I can't modify the local network further than the first router (10.0.0.1). That is the only different I've found so far. Any idea about how to solve it? Thank you.

  Read the article

• Mavericks permission issues with Windows Server deduplicated shares

  - by dmohlmaster

  We have a number of 10.9-10.9.3 - Mavericks - machines installed throughout our facility. Much of the user content is pulled from shares stored on our Windows Server 2012 fileservers with deduplication enabled. I have found that files newly written or unoptimized are able to be accessed without issue - read, written, modified, etc. Once the file gets optomized/deduplicated and Windows adds the P & L attributes - sparse and symlink - the Macs running Mavericks begin to have access issues. Once the files get deduplicated, users begin receiving read access errors when copying files (see error1 below). This happens when copying to folders within the current folder tree or copying somewhere to the local system. If you 'stop' the copy operation and retry a few more times, it may eventually work for the specific instance but fail again later. I am however, able to copy these files without issue via the terminal. Other systems running 10.7 do not experience the same issues and are able to access file server resources without issue. Many of the systems having issues are newer and thus not able to be downgraded to 10.8 or 10.7. I have tried finder replacements such as Pathfinder but the results are the same. I know this is at least similar to the issues many Mac users are already experiencing and posting about but I haven't seen it directly linked to deduplication and the attributes written by Windows server. Has anyone seen this issue? Have any solutions been found? Error 1: When copying files after the PL attributes have been set by deduplication. "One or more items can't be copied to "Foler" because you don't have permissions to read them. ******************************************' Via the system.log, I am also seeing the following error when accessing these deduplicated file shares. The reparse point tag listed below is "IO_REPARSE_TAG_DEDUP" Reported error: "smbfs_nget: filename.ext - unknown reparse point tag 0x80000013"

  Read the article

• How to embed/hardcode SRT subtitles into mp4 videos with VLC?

  - by Jens Bannmann

  I'm looking for a way to "burn in" or render/rembed/hardcode subtitles (from an SRT file) into an MP4 video with VLC. But no matter what options I use, it never works properly. I get a file that plays video way too fast (audio is normal), or one that plays normally, but actually does not have embedded subtitles. Also, with some options (like the one below) it does not play in QuickTime, only in VLC. So the main question is: how can I make this work in VLC? Secondary questions are: How do I decide which options I should set? Which settings are best if I want to leave the file bitrate etc. the same as much as possible, only embed subtitles? It seems I cannot leave the field empty or Video/Audio unchecked, so I guess I would first need to figure out the original audio and video bitrate. What do the "Scale" and "Channels" options mean? ... none of which are answered within the VLC documentation. For example, this is one set of options I used in the "Advanced Open File…" dialog: Advanced Open File… myFileName.mp4 [ ] Treat as a pipe rather than as a file [x] Load subtitles file: mySubtitleFileName.srt [ ] Play another media synchronously [x] Streaming/Saving Streaming and Transcoding Options [ ] Display the stream locally (o) File [outputFileName.mp4 ] [ ] Dump raw input Encapsulation Method: (MPEG 4 ) Transcoding options [x] Video (mp4v ) Bitrate (kb/s) [256 ] Scale [1 ] [x] Audio (mp3 ) Bitrate (kb/s) [128 ] Channels [1 ]

  Read the article

• Cut (smart edit) .mts (AVCHD Progressive) files un Ubuntu Lucid

  - by pts

  I have a bunch of .mts files containing AVCHD Progressive video recorded by a Panasonic camera, and I need software on Ubuntu Lucid with which I can remove the boring parts, and concatenate the interesting parts, all this without reencoding the video stream. It's OK for me to cut at keyframe boundary. If Avidemux was able to open the files, it would take about 60 hours of work for me to cut the files. (At least that was it last time I tried with similar videos, but of a file format supported by Avidemux.) So I need a fast, powerful and stable video editor, because I don't want that 60 hours of work go up to 240 or even 480 hours just because the tool is too slow or unstable or has a terrible UI. I've tried Avidemux 2.5.5 and 2.5.6, but they crash trying to open such a file, even if I convert the file to .avi first using mencoder -oac copy -ovc copy. mplayer can play the files. I've tried Avidemux 2.6.0, which can open the file, but it cannot jump to the previous or next keyframe etc. (if I make it jump to the next keyframe, and then to the previous keyframe, it doesn't end up at the original keyframe, sometimes displays an error etc.). Also I'm not sure if Avidemux 2.6.x would let me save the result without reencoding. I've tried Kdenlive 0.7.7.1, but playback is very choppy, and it cannot play audio at all (complaining that SDL cannot find the device; but many other programs on the system can play audio). It would be a pain to work with. I've tried converting the .mts file to .mkv using ffmpeg -i input.mts -vcodec copy -sameq -acodec copy -f matroska output.mkv, but that caused too much visible distortions in the video in both mplayer and Avidemux. I've tried converting the .mts file with TsRemux.exe, but Avidemux 2.5.x still can't open that file. Is there another program to cut and concatenate the files? Is there a preprocessor which would create a file (without reencoding the video) on which Avidemux wouldn't crash?

  Read the article

• Joining new DC to AD - DNS name does not exist

  - by Andrew Connell

  I had a DC fail on me recently and trying to add a new one to my domain, although I'm sensing I might have other issues in my domain. I'm a dev at heart and know just enough about AD to be dangerous so looking for some assistance. My working DC is RIVERCITY-DC12. I'm trying to promote RIVERCITY-DC14 as a DC to the RIVERCITY domain, but when I run DCPROMO, at the NETWORK CREDENTIALS step where I point to the name of the domain (rivercity.local), I get "An AD DC for the domain rivercity.local cannot be contacted" and in the details see "The error was DNS name does not exist" Looking at RIVERCITY-DC12, I can see DNS is working, I've been able to query it from other machines in my domain, and no errors are reported in the DNS category within the Event Viewer. When I checked the FMSO roles, it shows RIVERCITY-DC12 is the machine for all listed roles. Not sure what I should do next or how to troubleshoot/investigate after searching around for a solution... ideas? Environment: Domain: rivercity (rivercity.local) Forest functional level: Windows 2000 (I'm more than happy to raise this) Windows Server 2008 All servers are Windows Server 2008 R2 SP1 (fully patched)

  Read the article

• How to access previous VHD versions of system backup?

  - by feklee

  Quote from the 31 Oct 2009 TechNet article "Learn more about system image backup": During the first backup, the backup engine scans the source drive and copies only blocks that contain data into a .vhd file stored on the target, creating a compact view of the source drive. The next time a system image is created, only new and changed data is written to the .vhd file, and old data on the same block is moved out of the VHD and into the shadow copy storage area. Volume Shadow Copy Service is used to compute the changed data between backups, as well as to handle the process of moving the old data out to the shadow copy area on the target. This approach makes the backup fast (since only changed blocks are backed up) and efficient (since data is stored in a compact manner). When restoring the image, blocks will be restored to their original locations on the source disk. If you want to restore from an older backup, the engine reads from the shadow copy area and restores the appropriate blocks. For the last days, a daily system backup of drive C: to drive E: has been scheduled and run by Windows 7 Backup and Restore. Drive C: currently holds 233 GB of data, which fits comfortably on drive E:, a 1 TB drive, with 727 GB of free space remaining. How do I access the previous version of a VHD? I right clicked on files and folders in E:\WindowsImageBackup, and I looked for Previous Versions but always: There are no previous versions available

  Read the article

• Forcing programs to be installed to another drive

  - by zyboxenterprises

  I have an SSD as my main Windows drive, with a 640GB 2.5" HDD, partitioned to store programs and user settings, and also to act as backup (it's the only thing I had lying around at the time of building my PC). The task was to make the PC as fast as possible, while having an increased storage capacity available to store normal user data, and to assist in my small data recovery business. The problem is that whenever I install a program, it installs to C:\Program Files [(x86 for the 32 bit programs]\, although I have changed the environment variables. This wouldn't normally be an issue, however every installation program points its shortcut to my 640GB HDD. The root layout of both drives: To clarify: Program files get installed to C:\ Program shortcuts are always pointed to Z:\, my 640GB HDD Modifying the relevant environment variables doesn't do anything, I looked at this, but however it only talks about modifying the registry and environment variables, which I have already done so. I install to the Z:\ drive if the installation program lets me change the installation path, but however the installation programs sometimes don't let me change this. Is there a way that I can force every program to install to the relevant location on Z:\? Perhaps I'm missing something here? Edit: Found this program; would it be appropriate to use in my case? I would be able to move the entire Program Files (and its x86 version) to Z:\, without impacting on the performance.

  Read the article

• mysqldump skip one table

  - by danneth

  I'm running a cronjob to backup our system using mysqldump. The database contains 90 or so tables. One of these tables is HUGE and every once in a while causes the dump to fail. From the manual I see that you can specify specific tables to dump shell> mysqldump [options] db_name [tbl_name ...] This got me thinking. What if I have two jobs, one for dumping the huge table, and one for all the others. To accomplish this it would be nice if I could to something like shell> mysqldump -u backupuser -p database huge_table > db_huge_table.sql shell> mysqldump -u backupuser -p database --skip huge_table > db_rest.sql Unfortenately I'm not seeing such and option. I could of course explicitly state the 90 tables, but that just seems like a mess. Another option would be a script of some sort, but before checking that route I'll try this resource. MySQL is 5.1.61 on CentOS 6.2

  Read the article

< Previous Page | 287 288 289 290 291 292 293 294 295 296 297 298  | Next Page >