Search Results

Search found 7628 results on 306 pages for 'internal communications'.

Page 291/306 | < Previous Page | 287 288 289 290 291 292 293 294 295 296 297 298  | Next Page >

• fd partitions gone from 2 discs, md happy with it and resyncs. How to recover ?

  - by d0nd

  Hey gurus, need some help badly with this one. I run a server with a 6Tb md raid5 volume built over 7*1Tb disks. I've had to shut down the server lately and when it went back up, 2 out of the 7 disks used for the raid volume had lost its conf : dmesg : [ 10.184167] sda: sda1 sda2 sda3 // System disk [ 10.202072] sdb: sdb1 [ 10.210073] sdc: sdc1 [ 10.222073] sdd: sdd1 [ 10.229330] sde: sde1 [ 10.239449] sdf: sdf1 [ 11.099896] sdg: unknown partition table [ 11.255641] sdh: unknown partition table All 7 disks have same geometry and were configured alike : dmesg : Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect All 7 disks (sdb1, sdc1, sdd1, sde1, sdf1, sdg1, sdh1) were used in a md raid5 xfs volume. When booting, md, which was (obviously) out of sync kicked in and automatically started rebuilding over the 7 disks, including the two "faulty" ones; xfs tried to do some shenanigans as well: dmesg : [ 19.566941] md: md0 stopped. [ 19.817038] md: bind<sdc1> [ 19.817339] md: bind<sdd1> [ 19.817465] md: bind<sde1> [ 19.817739] md: bind<sdf1> [ 19.817917] md: bind<sdh> [ 19.818079] md: bind<sdg> [ 19.818198] md: bind<sdb1> [ 19.818248] md: md0: raid array is not clean -- starting background reconstruction [ 19.825259] raid5: device sdb1 operational as raid disk 0 [ 19.825261] raid5: device sdg operational as raid disk 6 [ 19.825262] raid5: device sdh operational as raid disk 5 [ 19.825264] raid5: device sdf1 operational as raid disk 4 [ 19.825265] raid5: device sde1 operational as raid disk 3 [ 19.825267] raid5: device sdd1 operational as raid disk 2 [ 19.825268] raid5: device sdc1 operational as raid disk 1 [ 19.825665] raid5: allocated 7334kB for md0 [ 19.825667] raid5: raid level 5 set md0 active with 7 out of 7 devices, algorithm 2 [ 19.825669] RAID5 conf printout: [ 19.825670] --- rd:7 wd:7 [ 19.825671] disk 0, o:1, dev:sdb1 [ 19.825672] disk 1, o:1, dev:sdc1 [ 19.825673] disk 2, o:1, dev:sdd1 [ 19.825675] disk 3, o:1, dev:sde1 [ 19.825676] disk 4, o:1, dev:sdf1 [ 19.825677] disk 5, o:1, dev:sdh [ 19.825679] disk 6, o:1, dev:sdg [ 19.899787] PM: Starting manual resume from disk [ 28.663228] Filesystem "md0": Disabling barriers, not supported by the underlying device [ 28.663228] XFS mounting filesystem md0 [ 28.884433] md: resync of RAID array md0 [ 28.884433] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [ 28.884433] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. [ 28.884433] md: using 128k window, over a total of 976759936 blocks. [ 29.025980] Starting XFS recovery on filesystem: md0 (logdev: internal) [ 32.680486] XFS: xlog_recover_process_data: bad clientid [ 32.680495] XFS: log mount/recovery failed: error 5 [ 32.682773] XFS: log mount failed I ran fdisk and flagged sdg1 and sdh1 as fd. I tried to reassemble the array but it didnt work: no matter what was in mdadm.conf, it still uses sdg and sdh instead of sdg1 and sdh1. I checked in /dev and I see no sdg1 and and sdh1, shich explains why it wont use it. I just don't know why those partitions are gone from /dev and how to readd those... blkid : /dev/sda1: LABEL="boot" UUID="519790ae-32fe-4c15-a7f6-f1bea8139409" TYPE="ext2" /dev/sda2: TYPE="swap" /dev/sda3: LABEL="root" UUID="91390d23-ed31-4af0-917e-e599457f6155" TYPE="ext3" /dev/sdb1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdc1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdd1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sde1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdf1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdg: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdh: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" fdisk -l : Disk /dev/sda: 40.0 GB, 40020664320 bytes 255 heads, 63 sectors/track, 4865 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8c878c87 Device Boot Start End Blocks Id System /dev/sda1 * 1 12 96358+ 83 Linux /dev/sda2 13 134 979965 82 Linux swap / Solaris /dev/sda3 135 4865 38001757+ 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc9bdc1e9 Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xcc356c30 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xe87f7a3d Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xb17a2d22 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdg: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8f3bce61 Device Boot Start End Blocks Id System /dev/sdg1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdh: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa98062ce Device Boot Start End Blocks Id System /dev/sdh1 1 121601 976760001 fd Linux raid autodetect I really dont know what happened nor how to recover from this mess. Needless to say the 5TB or so worth of data sitting on those disks are very valuable to me... Any idea any one? Did anybody ever experienced a similar situation or know how to recover from it ? Can someone help me? I'm really desperate... :x

  Read the article

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• Bind: dns not 'spreaded'

  - by realtebo

  I've elfoip.net with bind $ whois elfoip.net | grep 'Name Server' Name Server: NS.ELFOIP.NET I need elfoip.net be able to serve third levels domain, like mickymouse.elfoip.net, etc... Yes, I'm trying to create an other useless dyndns clone. i've added some third level as A RR. Eg: executing this from the server itself $ dig @localhost mattinauno.elfoip.net ;; ANSWER SECTION: mattinauno.elfoip.net. 60 IN A 192.81.221.113 I was expecting in one or two days, from my pc i can digit in browser mattinauno.elfoip.net and get page a 192.81.221.113 But this is not happening. Are there any prerequisites to satisfy to allow dns of my isp to be able to forward dns resolution of *.elfoip.net to MY dns ? (Or to ask to him and then cache ?) TTL of zone is set a 5m I've not AllowQuey directive, is it necessary for other dns to cache from mine ? I've cheched the zone with bind utility named-checkzone but no error detected. How to diagnose why other dns doesn't take in account RR from mine ? from my home pc dig @ns.elfoip.net mattinauno.elfoip.net ;; ANSWER SECTION: mattinauno.elfoip.net. 60 IN A 192.81.221.113 ;; AUTHORITY SECTION: elfoip.net. 300 IN NS ns.elfoip.net. but dig @8.8.8.8 mattinauno.elfoip.net give no answers Whole zone file: note I've used nsupdate, so this file has been re-edited and re-formatted from this utility ! root@mirko:/var/named# cat elfoip.net.db $ORIGIN . $TTL 300 ; 5 minutes elfoip.net IN SOA ns.elfoip.net. hostmaster.elfoip.net. ( 2013062314 ; serial 3600 ; refresh (1 hour) 600 ; retry (10 minutes) 86400 ; expire (1 day) 60 ; minimum (1 minute) ) NS ns.elfoip.net. A 109.168.99.6 $ORIGIN elfoip.net. $TTL 60 ; 1 minute google A 173.194.35.56 maiscai A 192.81.221.113 mattinadue A 192.81.221.113 mattinauno A 192.81.221.113 $TTL 300 ; 5 minutes ns A 109.168.99.6 $TTL 60 ; 1 minute prova A 208.67.222.222 prova2 A 13.23.34.45 A 13.23.34.46 www CNAME elfoip.net. EDIT: added named.conf.local zone "elfoip.net" { type master; // file "/etc/bind/elfoip.net.db"; file "/var/named/elfoip.net.db"; allow-update { key elfoip.net ; }; }; EDIT: I've no setup list-on directive *EDIT Added a TCPDUMP after [email protected] wwww.elfoip.net from a machine which uses my company internal dns, who allow recursive query. root@mirko:~# tcpdump -i eth0 'port 53' tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 11:57:23.293611 IP host9-210-static.22-87-b.business.telecomitalia.it.45958 > mirko.elfoip.net.domain: 61337+ A? www.elfoip.net. (32) 11:57:23.294114 IP mirko.elfoip.net.domain > host9-210-static.22-87-b.business.telecomitalia.it.45958: 61337* 2/1/1 CNAME elfoip.net., A 109.168.99.6 (95) 11:57:23.294554 IP mirko.elfoip.net.59571 > google-public-dns-a.google.com.domain: 45851+ PTR? 9.210.22.87.in-addr.arpa. (42) 11:57:23.330444 IP google-public-dns-a.google.com.domain > mirko.elfoip.net.59571: 45851 1/0/0 PTR host9-210-static.22-87-b.business.telecomitalia.it. (106) 11:57:23.331181 IP mirko.elfoip.net.44171 > google-public-dns-a.google.com.domain: 33339+ PTR? 8.8.8.8.in-addr.arpa. (38) 11:57:23.439405 IP google-public-dns-a.google.com.domain > mirko.elfoip.net.44171: 33339 1/0/0 PTR google-public-dns-a.google.com. (82) 11:57:31.350654 IP host9-210-static.22-87-b.business.telecomitalia.it.30108 > mirko.elfoip.net.domain: 38269 [1au] A? ns.elfoip.net. (42) 11:57:31.351117 IP mirko.elfoip.net.domain > host9-210-static.22-87-b.business.telecomitalia.it.30108: 38269* 1/1/1 A 109.168.99.6 (72) If i dig @8.8.8.8 www.elfoip.net, NOTHING happens in dump log !

  Read the article

• Remote Desktop Services Gateway Issue

  - by AVandelay05

  Alright fellow techies here's the rundown. I have installed Server 2008 r2 Remote Dekstop Services on a VM in my network. I installed the following RD role services: RD Session Host, Licensing, Connection Broker, Gateway, Web Access. When I set things up originally, the gateway server and RDWeb worked as it should locally. After getting things running locally (remoteserver.domainname.local) I wanted to test things externally. From the outside, I couldn't get things running (meaning I could connect to rdweb access externally, but when I tried to run an app I would get the message "can't connect/find computer"). Here's my setup for external access The VM has every RD Services role services installed on it, meaning it acts as gateway, rd web access, session host, licensing, the whole bit. I made a self-signed certificate on the gateway server (gateway.domainname.net is the cert name). Internally, I have a secondary forward-lookup zone called domainname.net with an A record gateway pointing to the local IP of the gateway server. On our public DNS (domainname.net) I have an A record gateway. This is to access the RDWeb externally. In IIS I have the following authentication settings RDWeb: All disabled except for anonymous authentication Rpc: All disabled except for basic and windows RpcWithCert: All disbled except for windows authentication I have the necessary web access config in our sonicwall tz210 (https and rdp, external ip pointing to local ip of rds server) RAP and CAP have the correct user and computer groups, authentication, and allowed devices After all of this, here's what happens accessing externally. I can login correctly to RDWeb Access (I've tried a bogus login, I can't login to it so that's working properly). I see the Apps for use. I click on an app, click connect, the credential window opens, I put in the correct user creds, it tries to connect to the gateway server, but then the cred window comes back in view. I tried to reach a limit of failed logins, but never reached one, haha. So from the same external client machine I try to connect to the gateway through a Remote Desktop connection. I put in the correct gateway settings in the RD window, try to connect and get the same results as I did in RDWeb access. I checked the event logs on the RD Services machine and saw the following event IDs around the time I tried to login externally: ID 6037 with the message "The program svchost.exe, with the assigned process ID 2168, could not authenticate locally by using the target name host/gateway.domainname.net. The target name used is not valid. A target name should refer to one of the local computer names, for example, the DNS host name. Try a different target name." ID 10 RADWebAccess "RD Web Access was unable to access gateway.domainname.net, which is the server that is specified as running the RemoteApp and Desktop Connection Management service. Ensure that the computer account of the RD Web Access server is a member of the TS Web Access Computers security group on gateway.domainname.net" ID 4625 "An account failed to log on. Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: Administrator Account Domain: gateway.domainname.net Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc000006a Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: USER-LAPTOP Source Network Address: External IP Source Port: 63125 Detailed Authentication Information: Logon Process: NtLmSsp Authentication Package: NTLM Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols." I don't think the VM has a null SID. The SID of the VM and it's physical host have different SIDS. I can access the blank page for rpc externally using the external gateway name. It seems like authentication is a problem. Also, is it a problem that the external name of the gateway server doesn't match the local name? The external name (which the cert is based on) is gateway.domainname.net and the internal name is remoteserver.domainname.local. That's the only thing I can think of that would be the problem, but the external name has to be different from the local right? Internally, I ping gateway.domainname.net and it gives me the correct local IP of the server. Now, there isn't an actual computer name in AD, but I don't know how I would achieve that? I hope I've been clear....any help would be appreciated. I think I'm close to achieving this. :)

  Read the article

• Deployment Workbench no longer available after PXE boot

  - by Patrick

  Our build process revolves around windows Deployment Workbench. Unfortunately this was setup by someone who is no longer with the company, and no-one has ever dared/needed to make any changes. The other day it stopped working. It turns out that one of our build guys started thinking about changing some stuff in it, clicked something and now it no longer works (He is saying now that he right clicked on the 'LAB' entry in 'Deployment points' and hit 'Update', which took some time to run through apparently). The job has fallen on me to resolve and frankly I'm not sure what I'm doing. I was wondering if someone with more experience than me can provide some pointers as to troubleshooting cos I'm feeling quite a lot in the dark here. On the server I have Deployment Workbench up and running (MMC snapin) version 3.0. There is a WDS service that appears to be running ok, as does the tFTPd service. Nothing specific to this in event logs. From the client side; PXE boot works and gets you to the Win PE launch, and it has the correct company logo as the background (proving to me that its loading win PE from the network). WPEINIT runs, and asks for domain credentials, here the team simply put User/Pass/Domain in the boxes and click ok. Normally the build would kick off. Instead they get an error message saying that the \NATBLU01\Distribution$ share isn't available. Checking \NATBLU01\Distribution$ shows that its there and accessible over the network. Security/permissions seem ok, even 'ANONYMOUS LOGON' has read access to that share so I don't see that being a problem. Digging the trace files from C:\MININT\SMSOSD\OSDLOGS\ after an attempt to run the build I can see an error saying much the same - <![LOG[Validating connection to \\NATBLU01\Distribution$]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[FindFile: The file OSDConnectToUNC.exe could not be found in any standard locations.]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[The network location cannot be reached. For information about network troubleshooting, see Windows Help.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> <![LOG[ERROR - Unable to map a network drive to \\NATBLU01\Distribution$.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> BDD.LOG shows much the same. Full copies of the .LOG files can both files be found here : BDD.LOG LITETOUCH.LOG I can get to a command prompt from the Win PE that boots from PXE, however there isn't any network stuff there. IPCONFIG returns nothing so none of the tests I would usually run resolve anything. I'm at a loss frankly. I did wonder if I could perhaps start a new build process but if the change to the DeploymentWorkbench has knocked it offline I don't think I'm going to be able to create a new deployment. Failing that; we do have a deployment point labeled type 'Media' which appears to be a DVD ISO image of one of the builds, but its dated 2008, is it possible to export the network build to .ISO and build from DVD? We are looking at new hardware to run this from anyway (for the impending Windows 7 roll out) so a temporary work round isn't going to be too much of a problem. All assistance is appreciated! EDIT : OK. Got it working again. Solution was close to Newmanth's idea. The problem was that our PE image didn't appear to be connecting the network. I had an older copy of the PE boot.WIM on a stick that I had been using for other purposes. I booted that and correctly got a network connection. Showed a correct internal IP and could ping out etc etc. However I was still getting the same errors in all the logs and in when wpeinit was running. What I did seperately was to update the PE image that DeploymentWorkbench was pushing out to display a different back ground. I wanted to prove that I was working in the correct place. Turns out that I wasn't. I went and looked at the other deployment stuff we had on this machine, Windows Deployment Services was installed and although all the install images are off line the boot image was online, so I uploaded the copy from my stick to that. Booted straight off. And fixed. Working. Yay! For anyone stumbling across this in the future you may find that although your deployment images are located in the DeploymentWorkbench, the Win PE boot image you are launching from is located in the associated Windows Deployment Services images.

  Read the article

• Can't update scala on Gentoo

  - by xhochy

  As I wanted to test Scala 2.9.2 on my gentoo system I tried updated the package but ended up with this error. I can't figure out where the problem may be: Calculating dependencies ...... done! >>> Verifying ebuild manifests >>> Jobs: 0 of 1 complete, 1 running Load avg: 0.23, 0.16, 0.20 >>> Emerging (1 of 1) dev-lang/scala-2.9.2 >>> Jobs: 0 of 1 complete, 1 running Load avg: 0.23, 0.16, 0.20 >>> Failed to emerge dev-lang/scala-2.9.2, Log file: >>> Jobs: 0 of 1 complete, 1 running Load avg: 0.23, 0.16, 0.20 >>> '/var/tmp/portage/dev-lang/scala-2.9.2/temp/build.log' >>> Jobs: 0 of 1 complete, 1 running Load avg: 0.23, 0.16, 0.20 >>> Jobs: 0 of 1 complete, 1 running, 1 failed Load avg: 0.23, 0.16, 0.20 >>> Jobs: 0 of 1 complete, 1 failed Load avg: 0.23, 0.16, 0.20 * Package: dev-lang/scala-2.9.2 * Repository: gentoo * Maintainer: [email protected] * USE: amd64 elibc_glibc kernel_linux multilib userland_GNU * FEATURES: sandbox [01m[31;06m!!! ERROR: Couldn't find suitable VM. Possible invalid dependency string. Due to jdk-with-com-sun requiring a target of 1.7 but the virtual machines constrained by virtual/jdk-1.6 and/or this package requiring virtual(s) jdk-with-com-sun[0m * Unable to determine VM for building from dependencies: NV_DEPEND: virtual/jdk:1.6 java-virtuals/jdk-with-com-sun !binary? ( dev-java/ant-contrib:0 ) app-arch/xz-utils >=dev-java/java-config-2.1.9-r1 source? ( app-arch/zip ) >=dev-java/ant-core-1.7.0 dev-java/ant-nodeps >=dev-java/javatoolkit-0.3.0-r2 >=dev-lang/python-2.4 * ERROR: dev-lang/scala-2.9.2 failed (setup phase): * Failed to determine VM for building. * * Call stack: * ebuild.sh, line 93: Called pkg_setup * scala-2.9.2.ebuild, line 43: Called java-pkg-2_pkg_setup * java-pkg-2.eclass, line 53: Called java-pkg_init * java-utils-2.eclass, line 2187: Called java-pkg_switch-vm * java-utils-2.eclass, line 2674: Called die * The specific snippet of code: * die "Failed to determine VM for building." * * If you need support, post the output of `emerge --info '=dev-lang/scala-2.9.2'`, * the complete build log and the output of `emerge -pqv '=dev-lang/scala-2.9.2'`. !!! When you file a bug report, please include the following information: GENTOO_VM= CLASSPATH="" JAVA_HOME="" JAVACFLAGS="" COMPILER="" and of course, the output of emerge --info * The complete build log is located at '/var/tmp/portage/dev-lang/scala-2.9.2/temp/build.log'. * The ebuild environment file is located at '/var/tmp/portage/dev-lang/scala-2.9.2/temp/die.env'. * Working directory: '/var/tmp/portage/dev-lang/scala-2.9.2' * S: '/var/tmp/portage/dev-lang/scala-2.9.2/work/scala-2.9.2-sources' * Messages for package dev-lang/scala-2.9.2: * Unable to determine VM for building from dependencies: * ERROR: dev-lang/scala-2.9.2 failed (setup phase): * Failed to determine VM for building. * * Call stack: * ebuild.sh, line 93: Called pkg_setup * scala-2.9.2.ebuild, line 43: Called java-pkg-2_pkg_setup * java-pkg-2.eclass, line 53: Called java-pkg_init * java-utils-2.eclass, line 2187: Called java-pkg_switch-vm * java-utils-2.eclass, line 2674: Called die * The specific snippet of code: * die "Failed to determine VM for building." * * If you need support, post the output of `emerge --info '=dev-lang/scala-2.9.2'`, * the complete build log and the output of `emerge -pqv '=dev-lang/scala-2.9.2'`. * The complete build log is located at '/var/tmp/portage/dev-lang/scala-2.9.2/temp/build.log'. * The ebuild environment file is located at '/var/tmp/portage/dev-lang/scala-2.9.2/temp/die.env'. * Working directory: '/var/tmp/portage/dev-lang/scala-2.9.2' * S: '/var/tmp/portage/dev-lang/scala-2.9.2/work/scala-2.9.2-sources' The following eix output may help: % eix java-virtuals/jdk-with-com-sun [I] java-virtuals/jdk-with-com-sun Available versions: 20111111 {{ELIBC="FreeBSD"}} Installed versions: 20111111(16:08:51 18/04/12)(ELIBC="-FreeBSD") Homepage: http://www.gentoo.org Description: Virtual ebuilds that require internal com.sun classes from a JDK Both virtual jdks 1.6 and 1.7 are installed: % eix virtual/jdk [I] virtual/jdk Available versions: (1.4) ~1.4.2-r1[1] (1.5) 1.5.0 ~1.5.0-r3[1] (1.6) 1.6.0 1.6.0-r1 (1.7) (~)1.7.0 Installed versions: 1.6.0-r1(1.6)(23:22:48 10/11/12) 1.7.0(1.7)(23:21:09 10/11/12) Description: Virtual for JDK [1] "java-overlay" /var/lib/layman/java-overlay

  Read the article

• Can't access shared drive when connecting over VPN

  - by evolvd

  I can ping all network devices but it doesn't seem that DNS is resolving their hostnames. ipconfig/ all is showing that I am pointing to the correct dns server. I can "ping "dnsname"" and it will resolve but it wont resolve any other names. Split tunnel is set up so outside DNS is resolving fine So one issue might be DNS but I have the IP address of the server share so I figure I could just get to it that way. example: \10.0.0.1\ well I can't get to it that way either and I get "the specified network name is no longer available" I can ping it but I can't open the share. Below is the ASA config : ASA Version 8.2(1) ! hostname KG-ASA domain-name example.com names ! interface Vlan1 nameif inside security-level 100 ip address 10.0.0.253 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns domain-lookup outside dns server-group DefaultDNS name-server 10.0.0.101 domain-name blah.com access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 10000 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 8333 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 902 access-list SPLIT-TUNNEL-VPN standard permit 10.0.0.0 255.0.0.0 access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool IPSECVPN-POOL 10.0.1.2-10.0.1.50 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 10000 10.0.0.101 10000 netmask 255.255.255.255 static (inside,outside) tcp interface 8333 10.0.0.101 8333 netmask 255.255.255.255 static (inside,outside) tcp interface 902 10.0.0.101 902 netmask 255.255.255.255 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication enable console LOCAL aaa authentication http console LOCAL aaa authentication serial console LOCAL aaa authentication ssh console LOCAL aaa authentication telnet console LOCAL http server enable http 10.0.0.0 255.255.0.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set myset esp-aes esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map dynmap 1 set transform-set myset crypto dynamic-map dynmap 1 set reverse-route crypto map IPSEC-MAP 65535 ipsec-isakmp dynamic dynmap crypto map IPSEC-MAP interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption aes hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 0.0.0.0 0.0.0.0 inside ssh 70.60.228.0 255.255.255.0 outside ssh 74.102.150.0 255.255.254.0 outside ssh 74.122.164.0 255.255.252.0 outside ssh timeout 5 console timeout 0 dhcpd dns 10.0.0.101 dhcpd lease 7200 dhcpd domain blah.com ! dhcpd address 10.0.0.110-10.0.0.170 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 63.111.165.21 webvpn enable outside svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable group-policy EASYVPN internal group-policy EASYVPN attributes dns-server value 10.0.0.101 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-policy tunnelspecified split-tunnel-network-list value SPLIT-TUNNEL-VPN ! tunnel-group client type remote-access tunnel-group client general-attributes address-pool (inside) IPSECVPN-POOL address-pool IPSECVPN-POOL default-group-policy EASYVPN dhcp-server 10.0.0.253 tunnel-group client ipsec-attributes pre-shared-key * tunnel-group CLIENTVPN type ipsec-l2l tunnel-group CLIENTVPN ipsec-attributes pre-shared-key * ! class-map inspection_default match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect icmp ! service-policy global_policy global prompt hostname context I'm not sure where I should go next with troubleshooting nslookup result: Default Server: blahname.blah.lan Address: 10.0.0.101

  Read the article

• Cisco: unable to negotiate IP using IPCP with Windows server

  - by lnk

  I am connecting to Windows server using PPP (for vpn), I establish connection but server does not respond me for my address requests: *Mar 23 00:40:06.055: Vi1 MS-CHAP-V2: I CHALLENGE id 0 len 25 from "MSDC" *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using hostname from interface CHAP *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using password from interface CHAP *Mar 23 00:40:06.067: Vi1 MS-CHAP-V2: O RESPONSE id 0 len 69 from "XXX" *Mar 23 00:40:06.087: Vi1 PPP: I pkt type 0xC223, datagramsize 50 link[ppp] *Mar 23 00:40:06.087: Vi1 MS-CHAP-V2: I SUCCESS id 0 len 46 msg is "S=XXX" *Mar 23 00:40:06.087: Vi1 MS CHAP V2 No Password found for : XXX *Mar 23 00:40:06.091: Vi1 MS CHAP V2 Check AuthenticatorResponse Success for : XXX *Mar 23 00:40:06.091: Vi1 IPCP: O CONFREQ [Closed] id 1 len 20 *Mar 23 00:40:06.091: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:06.091: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:07.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up *Mar 23 00:40:07.091: Vi1 LCP: O ECHOREQ [Open] id 1 len 12 magic 0x194CAFCF *Mar 23 00:40:07.103: Vi1 LCP-FS: I ECHOREP [Open] id 1 len 12 magic 0x361B62E5 *Mar 23 00:40:07.103: Vi1 LCP-FS: Received id 1, sent id 1, line up *Mar 23 00:40:08.083: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:08.083: Vi1 IPCP: O CONFREQ [REQsent] id 2 len 20 *Mar 23 00:40:08.083: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:08.083: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:10.099: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:10.099: Vi1 IPCP: O CONFREQ [REQsent] id 3 len 20 *Mar 23 00:40:10.099: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:10.099: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.115: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:12.115: Vi1 IPCP: O CONFREQ [REQsent] id 4 len 20 *Mar 23 00:40:12.115: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:12.115: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.211: Vi1 LCP: O ECHOREQ [Open] id 2 len 12 magic 0x194CAFCF *Mar 23 00:40:12.219: Vi1 LCP-FS: I ECHOREP [Open] id 2 len 12 magic 0x361B62E5 *Mar 23 00:40:12.219: Vi1 LCP-FS: Received id 2, sent id 2, line up *Mar 23 00:40:14.131: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:14.131: Vi1 IPCP: O CONFREQ [REQsent] id 5 len 20 *Mar 23 00:40:14.131: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:14.131: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:16.147: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:16.147: Vi1 IPCP: O CONFREQ [REQsent] id 6 len 20 *Mar 23 00:40:16.147: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:16.147: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:17.331: Vi1 LCP: O ECHOREQ [Open] id 3 len 12 magic 0x194CAFCF *Mar 23 00:40:17.343: Vi1 LCP-FS: I ECHOREP [Open] id 3 len 12 magic 0x361B62E5 *Mar 23 00:40:17.343: Vi1 LCP-FS: Received id 3, sent id 3, line up You see: My router asks for address, but only keepalives are on line. But the same server works with windows client!! ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service internal ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! resource policy ! ip subnet-zero ! ! ip cef vpdn enable ! vpdn-group pptp request-dialin protocol pptp pool-member 1 initiate-to ip XXXX ! ! ! ! ! ! ! bridge irb ! ! interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface Dot11Radio0 no ip address shutdown speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Vlan1 no ip address bridge-group 1 ! interface Dialer0 ip address negotiated encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer string XXX dialer persistent dialer vpdn dialer-group 1 keepalive 5 3 no cdp enable ppp authentication ms-chap-v2 optional ppp eap refuse ppp chap hostname XXX ppp chap password 0 XXX ppp ipcp mask request ppp ipcp ignore-map ppp ipcp address accept ! interface BVI1 mac-address XXX.XXX.XXX ip address dhcp ! ip classless ip route 172.0.0.0 255.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! dialer-list 1 protocol ip permit ! control-plane ! bridge 1 protocol vlan-bridge bridge 1 route ip ! line con 0 no modem enable line aux 0 line vty 0 4 login ! scheduler max-task-time 5000 end

  Read the article

• Making nginx withstand flood attacks

  - by Tiffany Walker

  How can I make it stand stand against attacks better? Are their plugins. Looking for a way to RATE LIMIT and remain up and not slow down. My Setup: user nobody; # no need for more workers in the proxy mode worker_processes 4; worker_cpu_affinity 0001 0010 0100 1000; worker_priority -2; error_log /var/log/nginx/error.log info; worker_rlimit_nofile 40480; events { worker_connections 5120; # increase for busier servers use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks if_not_owner; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 5; gzip on; gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 9; gzip_buffers 16 8k; # You can remove image/png image/x-icon image/gif image/jpeg if you have slow CPU gzip_types text/plain text/xml text/css application/x-javascript application/xml image/png image/x-icon image/gif image/jpeg application/xml+rss text/javascript application/atom+xml; ignore_invalid_headers on; client_header_timeout 3m; client_body_timeout 3m; send_timeout 3m; reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 200M; client_body_buffer_size 128k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; include "/etc/nginx/vhosts/*"; } vhost file: server { error_log /var/log/nginx/vhost-error_log warn; listen 194.145.208.19:80; server_name ipxnow.in www.ipxnow.in; access_log /usr/local/apache/domlogs/ipxnow.in-bytes_log bytes_log; access_log /usr/local/apache/domlogs/ipxnow.in combined; root /home/ipxnowin/public_html; location / { location ~.*\.(3gp|gif|jpg|jpeg|png|ico|wmv|avi|asf|asx|mpg|mpeg|mp4|pls|mp3|mid|wav|swf|flv|html|htm|txt|js|css|exe|zip|tar|rar|gz|tgz|bz2|uha|7z|doc|docx|xls|xlsx|pdf|iso)$ { expires 7d; try_files $uri @backend; } error_page 405 = @backend; add_header X-Cache "HIT from Backend"; proxy_pass http://194.145.208.19:8081; include proxy.inc; } location @backend { internal; proxy_pass http://194.145.208.19:8081; include proxy.inc; } location ~ .*\.(php|jsp|cgi|pl|py)?$ { proxy_pass http://194.145.208.19:8081; include proxy.inc; } location ~ /\.ht { deny all; } } and proxy.inc: proxy_connect_timeout 59s; proxy_send_timeout 600; proxy_read_timeout 600; proxy_buffer_size 64k; proxy_buffers 16 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; proxy_pass_header Set-Cookie; proxy_redirect off; proxy_hide_header Vary; proxy_set_header Accept-Encoding ''; proxy_ignore_headers Cache-Control Expires; proxy_set_header Referer $http_referer; proxy_set_header Host $host; proxy_set_header Cookie $http_cookie; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Host $host; proxy_set_header X-Forwarded-Server $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;

  Read the article

• slow DNS resolution

  - by Ehsan

  I have a DNS server that resolves all queries for an internal group of servers. It is a bind on CentOS 5.5 (same as RHEL5) and I have set it up to allow recursion and resolve direction without any forwarders. The problem I am facing is that it takes a freakishly long amount of time to resolve a name for the first time. (in the magnitudes of 20 sec) This causes clients to give timeout. When I set it to forward all to Google's public DNS, i.e. 8.8.8.8+8.8.4.4, it works very nicely (within a second). I tried monitoring the traffic on the net to see why it is doing this: [root@ns1 ~]# tcpdump -nnvvvA -s0 udp tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 23:06:36.137797 IP (tos 0x0, ttl 64, id 35903, offset 0, flags [none], proto: UDP (17), length: 60) 172.17.1.10.36942 > 172.17.1.4.53: [udp sum ok] 19773+ A? www.paypal.com. (32) E..<[email protected]... .....N.5.(6.M=...........www.paypal.com..... 23:06:36.140594 IP (tos 0x0, ttl 64, id 56477, offset 0, flags [none], proto: UDP (17), length: 71) 172.17.1.4.6128 > 192.35.51.30.53: [udp sum ok] 10105 [1au] A? www.paypal.com. ar: . OPT UDPsize=4096 (43) E..G....@........#3....5.3fR'y...........www.paypal.com.......)........ 23:06:38.149756 IP (tos 0x0, ttl 64, id 13078, offset 0, flags [none], proto: UDP (17), length: 71) 172.17.1.4.52425 > 192.54.112.30.53: [udp sum ok] 54892 [1au] A? www.paypal.com. ar: . OPT UDPsize=4096 (43) [email protected]&.....6p....5.3.q.l...........www.paypal.com.......)........ 23:06:40.159725 IP (tos 0x0, ttl 64, id 43016, offset 0, flags [none], proto: UDP (17), length: 71) 172.17.1.4.24059 > 192.42.93.30.53: [udp sum ok] 11205 [1au] A? www.paypal.com. ar: . OPT UDPsize=4096 (43) E..G....@..@.....*].]..5.3..+............www.paypal.com.......)........ 23:06:41.141403 IP (tos 0x0, ttl 64, id 35904, offset 0, flags [none], proto: UDP (17), length: 60) 172.17.1.10.36942 > 172.17.1.4.53: [udp sum ok] 19773+ A? www.paypal.com. (32) E..<.@..@..@... .....N.5.(6.M=...........www.paypal.com..... 23:06:42.169652 IP (tos 0x0, ttl 64, id 44001, offset 0, flags [none], proto: UDP (17), length: 60) 172.17.1.4.9141 > 192.55.83.30.53: [udp sum ok] 1184 A? www.paypal.com. (32) E..<[email protected].#..5.(...............www.paypal.com..... 23:06:42.207295 IP (tos 0x0, ttl 54, id 38004, offset 0, flags [none], proto: UDP (17), length: 205) 192.55.83.30.53 > 172.17.1.4.9141: [udp sum ok] 1184- q: A? www.paypal.com. 0/3/3 ns: paypal.com. NS ns1.isc-sns.net., paypal.com. NS ns2.isc-sns.com., paypal.com. NS ns3.isc-sns.info. ar: ns1.isc-sns.net. AAAA 2001:470:1a::1, ns1.isc-sns.net. A 72.52.71.1, ns2.isc-sns.com. A 38.103.2.1 (177) E....t..6./A.7S......5#..................www.paypal.com..................ns1.isc-sns.net..............ns2.isc-sns...............ns3.isc-sns.info..,.......... ..p.............,..........H4G..I..........&g.. (this goes on for a few more seconds) If you look carefully, you will see that the first 3-4 root servers did not respond at all. This wastes 7-8 seconds, until one of them responded. Do you think I have setup something wrong here? Interestingly, when I dig directly from the root servers that did not respond, the always respond very fast (showing the firewall/nat is not the issue here). E.g. dig www.paypal.com @192.35.51.30 works perfectly, consistently, and very fast. What do you think about this mystery?

  Read the article

• ESXi v5.5 is having random crashes

  - by Darkmage

  HW: Type: HP Proliant ML350 G5 RAM 22GB CPU 1 x Intel Xenon E5405 2.00GHz OP: ESXi 5.5 just updated from 5.1 to try and fix the crashes occurring on ESXi 5.1 on same hardware. I'm trying to find the error on why one of our servers is crashing, it has had two lock ups in 24 hours now. The internal error light on the front is blinking red, on the inside only "#5 and #6 page 76 manual" the "Processor 2" light "amber" and the "Power" light "green" is shining. in the logs the only errors i can see in the relevant time frame is in log under. Is this the reason? or is there anything else i can do to try and log/locate the error. from zcat syslog.6.gz | less 2014-05-26T11:55:47Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:55:47Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:55:47Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:53Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:57Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:01Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:04Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:15Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:56:17Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:56:17Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:23Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:27Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:31Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:46Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:48Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files -- manual

  Read the article

• Why are my USB 2.0 devices crashing Windows XP?

  - by BenAlabaster

  Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic ATX motherboard with no identifying markings other than one stamp that says "Rev.B". CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. On board it has 1 x 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. It has a DVD+/-RW running as master on IDE1 and a 1.44Mb 3.5" floppy drive connected to the floppy connector. It has an 80Gb Western Digital hard drive running as master on IDE0. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. The hard disk is freshly formatted and built with Windows XP Professional/Service Pack 3 and is up to date with all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 hangs the whole machine as soon as it starts up, requiring a hard boot to recover). It's got a Daytek MV150 15" touch screen hooked up to the on board VGA and COM1 sockets with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem: If I hook any devices to the USB 2.0 sockets, it hangs the whole machine and I have to hard boot it to get it back up. If I have any devices attached to the USB 2.0 sockets when I boot up, it hangs before Windows gets to the login prompt and I have to hard boot it to recover. Workarounds found: I can plug the same devices into the on board USB 1.0 sockets and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions: I've seen suggestions that this could be a power problem - that the PSU just doesn't have the wattage to drive these ports. While I'm doubtful this is the problem [after all the motherboard has the same standard connector regardless of the PSU wattage], I tried disabling all the on board devices that I'm not using - on board LAN, the second COM port, the AGP connector etc. through the BIOS in what I'm sure is a futile attempt to reduce the power consumption... I also modified the ACPI and power management settings. It didn't have any noticeable affect, although it didn't do any harm either. Could the wattage of the PSU really cause this problem? If it can, is there anything I need to be aware of when replacing it or do I just need to make sure it's got a higher wattage than the current one? My interpretation was that the wattage only affected the number of drives you could hook up to the power connectors, is that right? I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself, and Windows says the card is installed and working correctly... right up until I connect a device to it. The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference - does anyone have any experience that would suggest this might work? Other thoughts/questions: Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question: Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

  Read the article

• Windows 8, NVIDIA graphics recognition fails

  - by Roy Grubb

  I just installed Windows 8 Pro OEM 64-bit (clean install) and it won't properly recognize my graphics adapter. When I installed Win8, it automatically installed the BasicDisplay.sys driver dated 6/21/2006. 6.2.9200.16384 (win8_rtm.120725-1247). Hardware - Mobo:MSi G41M-P33 Combo CPU:Intel CoreDuo 6600 Graphics:NVIDIA GeForce 9400GT *OS* - Windows 8 Pro 64-bit OEM The graphics adapter worked fine in Windows XP. The PC is a generic box, bought locally and its mobo failed recently, so I replaced it with the G41M. Microsoft wouldn't let me re-activate Windows XP with a different mobo, so I installed Win8, which appears to work except as described next. Win8 only partially recognizes the graphics adapter and won't allow NVIDIA latest driver installer to see that it's an NVIDIA card. As a result, OpenGL doesn't work, and this is needed by the software I most use. Other than that the graphics look OK. When I say 'partially recognizes', I mean that via the Control Panel, I can see that the adapter is described as NVIDIA, but the driver remains stuck at Microsoft Basic Display Adapter no matter what I try, including "Update driver..." in adapter properties. Display Screen Resolution Advanced Settings Adapter shows: Adapter Type: Microsoft Basic Display Adapter Chip Type: NVIDIA DAC Type: NVIDIA Corporation Bios Information: G27 Board - p381n17 Don't know what this means ... no mention of 9400GT Total Available Graphics Memory: 256 MB Dedicated Video Memory: 0 MB In fact the adapter has 512MB on-board video memory. System Video Memory: 0 MB Shared System Memory: 256 MB And Control Panel Device Manager Display adapters just shows Microsoft Basic Display Adapter. No other graphics adapter, and no unknown device or yellow question mark. What I have tried so far: 1. Cleared CMOS and reset. Updated BIOS and all mobo drivers as follows: 1st I used Driver Reviver to see if any driver updates were required. It found some but I didn't use that to get the drivers. Then I switched to MSi's own mobo driver utility Live Update 5. This also showed the board needed to update several so I used it to fetch the new drivers. After that it showed that everything was up to date and I checked with Driver Reviver again, which also reported no drivers now needed updating. Rebooted. Went to the NVIDIA site to get the latest graphics adapter driver. Their auto-detect "Option 2: Automatically find drivers for my NVIDIA products" said "The NVIDIA Smart Scan was unable to evaluate your system hardware. Please use Option 1 to manually find drivers for your NVIDIA products." So I downloaded 310.70-desktop-win8-win7-winvista-64bit-international-whql.exe, which lists 9400 GT under supported products, but when I run it, it says: "NVIDIA Installer cannot continue This graphics driver could not find compatible graphics hardware." Connected the display to the on-board Intel graphics (G41 Intel Express), removed the NVIDIA card and rebooted, changed to internal graphics in CMOS. Again it installs the MS Basic Display Adapter, and can't properly run my s/w that needs OpenGL. It runs on other machines with Intel Express graphics (WinXP and 7) Shut down and pulled out the power cord. Held start button to discharge all capacitors. Removed and re-inserted NVIDIA adapter in PCI-E slot and made sure properly seated. Connected the monitor to the card, screwed plug to socket. Reconnected power cord. Started and checked in BIOS that Primary Graphics Adapter was set to PCI-E. Started Windows. Uninstalled MS Basic Display Adapter in Device Manager. Screen blanks briefly, reappears. No Graphics adapter entry was then visible in Device Manager. Restarted PC. MS Basic Display Adapter Visible again in Device Manager. Clicked in Device Manager View Show hidden devices. No other graphics adapter appears, no unknown devices. Rebooted. Tried Scan for Hardware changes. None detected. Tried right-click on MS Basic Display Adapter Properties Driver Update Driver... Search automatically. It replied that it had determined driver was up to date. I checked that there were no graphic driver-related entries in Programs and Features that I could delete (none). Searched for any other drivers with nvidia in their name and deleted them, just keeping the 306.97 installer exe file. Did a Windows Update. Ran GPU-Z which shows (main items): Microsoft Basic Display Adapter GPU G72 BIOS 5.72.22.76.88 Device ID 10DE - 01D5 DDR2 Bus Width 32 Bit Memory size 64MB Driver Version nvlddmkm 6.2.9200.16384 (ForceWare 0.00) / Win8 64 NVIDIA SLI Unknown in the drop-down at the foot, "Microsoft Basic Display Adapter" is the only option If I swap hard disks in that machine to one with a Ubuntu 10.4 installation (originally installed on the same PC), lspci shows "VGA compatible controller as NVIDIA Corporation Device 01d5 (rev a1) (prog-if 00 [VGA controller])" and "kernel driver in use: nvidia" I'm out of ideas for new things to try and would be really grateful of suggestions. Thanks!

  Read the article

• Nginx reverse proxy IP issue

  - by Tiffany Walker

  For some reason Apache is still seeing my SERVERS ip. Is this an nginx problem? /etc/nginx.conf user nobody; # no need for more workers in the proxy mode worker_processes 4; error_log /var/log/nginx/error.log info; worker_rlimit_nofile 20480; events { worker_connections 5120; # increase for busier servers use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks if_not_owner; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 5; gzip on; gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; # You can remove image/png image/x-icon image/gif image/jpeg if you have slow CPU gzip_types text/plain text/xml text/css application/x-javascript application/xml image/png image/x-icon image/gif image/jpeg application/xml+rss text/javascript application/atom+xml; ignore_invalid_headers on; client_header_timeout 3m; client_body_timeout 3m; send_timeout 3m; reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 200M; client_body_buffer_size 128k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; include "/etc/nginx/vhosts/*"; } proxy.inc proxy_connect_timeout 59s; proxy_send_timeout 600; proxy_read_timeout 600; proxy_buffer_size 64k; proxy_buffers 16 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; proxy_pass_header Set-Cookie; proxy_redirect off; proxy_hide_header Vary; proxy_set_header Accept-Encoding ''; proxy_ignore_headers Cache-Control Expires; proxy_set_header Referer $http_referer; proxy_set_header Host $host; proxy_set_header Cookie $http_cookie; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Host $host; proxy_set_header X-Forwarded-Server $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; vhost file: server { error_log /var/log/nginx/vhost-error_log warn; listen 63.6.1.12:80; server_name photo-rolldomain.com www.domain.com; access_log /usr/local/apache/domlogs/domain.com-bytes_log bytes_log; access_log /usr/local/apache/domlogs/domain.com combined; root /home/mtech/public_html; location / { location ~.*\.(3gp|gif|jpg|jpeg|png|ico|wmv|avi|asf|asx|mpg|mpeg|mp4|pls|mp3|mid|wav|swf|flv|html|htm|txt|js|css|exe|zip|tar|rar|gz|tgz|bz2|uha|7z|doc|docx|xls|xlsx|pdf|iso)$ { expires 7d; try_files $uri @backend; } error_page 405 = @backend; add_header X-Cache "HIT from Backend"; proxy_pass http://63.6.1.12:8081; include proxy.inc; } location @backend { internal; proxy_pass http://63.6.1.12:8081; include proxy.inc; } location ~ .*\.(php|jsp|cgi|pl|py)?$ { proxy_pass http://63.6.1.12:8081; include proxy.inc; } location ~ /\.ht { deny all; } }

  Read the article

• Why are my USB 2.0 devices hanging Windows XP?

  - by BenAlabaster

  Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic ATX motherboard with no identifying markings other than one stamp that says "Rev.B". CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. On board it has 1 x 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors - it has a NEC uPD720102 chipset. It has a DVD+/-RW running as master on IDE1 and a 1.44Mb 3.5" floppy drive connected to the floppy connector. It has an 80Gb Western Digital hard drive running as master on IDE0. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. The hard disk is freshly formatted and built with Windows XP Professional/Service Pack 3 and is up to date with all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 hangs the whole machine as soon as it starts up, requiring a hard boot to recover). It's got a Daytek MV150 15" touch screen hooked up to the on board VGA and COM1 sockets with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem: If I hook any devices to the USB 2.0 sockets, it hangs the whole machine and I have to hard boot it to get it back up. If I have any devices attached to the USB 2.0 sockets when I boot up, it hangs before Windows gets to the login prompt and I have to hard boot it to recover. Workarounds found: I can plug the same devices into the on board USB 1.0 sockets and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions: I've seen suggestions that this could be a power problem - that the PSU just doesn't have the wattage to drive these ports. While I'm doubtful this is the problem [after all the motherboard has the same standard connector regardless of the PSU wattage], I tried disabling all the on board devices that I'm not using - on board LAN, the second COM port, the AGP connector etc. through the BIOS in what I'm sure is a futile attempt to reduce the power consumption... I also modified the ACPI and power management settings. It didn't have any noticeable affect, although it didn't do any harm either. Could the wattage of the PSU really cause this problem? If it can, is there anything I need to be aware of when replacing it or do I just need to make sure it's got a higher wattage than the current one? My interpretation was that the wattage only affected the number of drives you could hook up to the power connectors, is that right? I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself, and Windows says the card is installed and working correctly... right up until I connect a device to it. The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference - does anyone have any experience that would suggest this might work? Other thoughts/questions: Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question: Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine? Edit: Updated the USB 2.0 info with reference to actual card - http://www.xpcgear.com/lpnec4u.html

  Read the article

• Nginx & Apache Cannot get try_files to work with permalinks

  - by tcherokee

  I have been working on this for the past two weeks not and for some reason I cannot seem to get nginx's try_files to work with my wordpress permalinks. I am hoping someone will be able to tell me where I am going wrong and also hopefully tell me if I made any major errors with my configurations as well (I am an nginx newbie... but learning :) ). Here are my Configuration files nginx.conf user www-data; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; # server_names_hash_bucket_size 64; # server_name_in_redirect off; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## # Defines the cache log format, cache log location # and the main access log location. log_format cache '***$time_local ' '$upstream_cache_status ' 'Cache-Control: $upstream_http_cache_control ' 'Expires: $upstream_http_expires ' '$host ' '"$request" ($status) ' '"$http_user_agent" ' ; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } mydomain.com.conf server { listen 123.456.78.901:80; # IP goes here. server_name www.mydomain.com mydomain.com; #root /var/www/mydomain.com/prod; index index.php; ## mydomain.com -> www.mydomain.com (301 - Permanent) if ($host !~* ^(www|dev)) { rewrite ^/(.*)$ $scheme://www.$host/$1 permanent; } # Add trailing slash to */wp-admin requests. rewrite /wp-admin$ $scheme://$host$uri/ permanent; # All media (including uploaded) is under wp-content/ so # instead of caching the response from apache, we're just # going to use nginx to serve directly from there. location ~* ^/(wp-content|wp-includes)/(.*)\.(jpg|png|gif|jpeg|css|js|m$ root /var/www/mydomain.com/prod; } # Don't cache these pages. location ~* ^/(wp-admin|wp-login.php) { proxy_pass http://backend; } location / { if ($http_cookie ~* "wordpress_logged_in_[^=]*=([^%]+)%7C") { set $do_not_cache 1; } proxy_cache_key "$scheme://$host$request_uri $do_not_cache"; proxy_cache main; proxy_pass http://backend; proxy_cache_valid 30m; # 200, 301 and 302 will be cached. # Fallback to stale cache on certain errors. # 503 is deliberately missing, if we're down for maintenance # we want the page to display. #try_files $uri $uri/ /index.php?q=$uri$args; #try_files $uri =404; proxy_cache_use_stale error timeout invalid_header http_500 http_502 http_504 http_404; } # Cache purge URL - works in tandem with WP plugin. # location ~ /purge(/.*) { # proxy_cache_purge main "$scheme://$host$1"; # } # No access to .htaccess files. location ~ /\.ht { deny all; } } # End server gzip.conf # Gzip Configuration. gzip on; gzip_disable msie6; gzip_static on; gzip_comp_level 4; gzip_proxied any; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; proxy.conf # Set proxy headers for the passthrough proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_max_temp_file_size 0; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffer_size 4k; proxy_buffers 4 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; add_header X-Cache-Status $upstream_cache_status; backend.conf upstream backend { # Defines backends. # Extracting here makes it easier to load balance # in the future. Needs to be specific IP as Plesk # doesn't have Apache listening on localhost. ip_hash; server 127.0.0.1:8001; # IP goes here. } cache.conf # Proxy cache and temp configuration. proxy_cache_path /var/www/nginx_cache levels=1:2 keys_zone=main:10m max_size=1g inactive=30m; proxy_temp_path /var/www/nginx_temp; proxy_cache_key "$scheme://$host$request_uri"; proxy_redirect off; # Cache different return codes for different lengths of time # We cached normal pages for 10 minutes proxy_cache_valid 200 302 10m; proxy_cache_valid 404 1m; The two commented out try_files in location \ of the mydomain config files are the ones I tried. This error I found in the error log can be found below. ...rewrite or internal redirection cycle while internally redirecting to "/index.php" Thanks in advance

  Read the article

• Error Installing COM+ (Error Code: 80131501)

  - by Regina Foo

  I've written a class library that reads from an xml file and return the result as a string. But when I want to install it as a COM+ component, an error occurred (Error Code: 80131501). I checked the event log and the details of the error is: Installation of 'C:\Users\User\Documents\Visual Studio 2005\Projects\InteropSOA\InteropSOA\bin\Debug\InteropSOA.dll' into '{28E82165-AD74-4E16-90C9-0C5CE7DA97AA}' failed with an exception: System.EnterpriseServices.RegistrationException: FATAL: Could not find component 'InteropSOA.ConfigReader' we just installed. at System.EnterpriseServices.RegistrationDriver.InstallAssembly(RegistrationConfig regConfig, Object obSync) at System.EnterpriseServices.RegistrationHelper.InstallAssemblyFromConfig(RegistrationConfig& regConfig) at System.EnterpriseServices.RegistrationHelper.InstallAssembly(String assembly, String& application, String partition, String& tlb, InstallationFlags installFlags) at System.EnterpriseServices.Internal.ComManagedImportUtil.InstallAssembly(String asmpath, String parname, String appname) Below are the steps I've done while developing the class library: Added "System.EnterpriseServices" to Reference. Imported the reference to the class. Declared the class as "ServicedComponent". Set project properties ("Make assembly COM-visible" checked, "Register for COM Interop" checked, Signed the assembly with a strong key file name.) Here are my codes: using System; using System.Collections.Generic; using System.Text; using System.Xml; using System.Xml.XPath; using System.EnterpriseServices; namespace InteropSOA { public class ConfigReader : ServicedComponent { // xml file name private string strFileName; // type of request private string strRequest = ""; // response string private string strResponse = ""; // declarations for xPath private XPathDocument doc; private XPathNavigator nav; private XPathExpression expr; private XPathNodeIterator iterator; private XmlTextReader reader; private XmlDocument xmlDoc; public ConfigReader(string strFile, string request) { this.strFileName = strFile; this.strRequest = request; } public ConfigReader() { //default contructor } // reader for console program public void ReadXML() { doc = new XPathDocument(strFileName); nav = doc.CreateNavigator(); // compile xPath expression expr = nav.Compile("/Msg/" + strRequest + "/*"); iterator = nav.Select(expr); // interate on the node set try { while (iterator.MoveNext()) { XPathNavigator nav2 = iterator.Current.Clone(); strResponse += nav2.Value + "|"; } } catch (Exception ex) { Console.WriteLine(ex.Message); } strResponse = strResponse.Substring(0, strResponse.Length-1); Console.WriteLine("Response string = " + strResponse); } public void WriteXML(string strRequest, string strElement, string strValue) { reader = new XmlTextReader(strFileName); xmlDoc = new XmlDocument(); xmlDoc.Load(reader); reader.Close(); XmlNode node; XmlElement root = xmlDoc.DocumentElement; node = root.SelectSingleNode("/Msg/" + strRequest + "/" + strElement); node.InnerText = strValue; xmlDoc.Save(strFileName); } // reader for ASP.NET public string ReadXMLElement() { doc = new XPathDocument(strFileName); nav = doc.CreateNavigator(); // compile xPath expression expr = nav.Compile("/Msg/" + strRequest + "/*"); iterator = nav.Select(expr); // interate on the node set try { while (iterator.MoveNext()) { XPathNavigator nav2 = iterator.Current.Clone(); strResponse += nav2.Value + "|"; } } catch (Exception ex) { Console.WriteLine(ex.Message); } strResponse = strResponse.Substring(0, strResponse.Length - 1); return strResponse; } } }

  Read the article

• These are few objective type questions which i was not able to find the solution [closed]

  - by Tarun

  1. Which of the following advantages does System.Collections.IDictionaryEnumerator provide over System.Collections.IEnumerator? a. It adds properties for direct access to both the Key and the Value b. It is optimized to handle the structure of a Dictionary. c. It provides properties to determine if the Dictionary is enumerated in Key or Value order d. It provides reverse lookup methods to distinguish a Key from a specific Value 2. When Implementing System.EnterpriseServices.ServicedComponent derived classes, which of the following statements are true? a. Enabling object pooling requires an attribute on the class and the enabling of pooling in the COM+ catalog. b. Methods can be configured to automatically mark a transaction as complete by the use of attributes. c. You can configure authentication using the AuthenticationOption when the ActivationMode is set to Library. d. You can control the lifecycle policy of an individual instance using the SetLifetimeService method. 3. Which of the following are true regarding event declaration in the code below? class Sample { event MyEventHandlerType MyEvent; } a. MyEventHandlerType must be derived from System.EventHandler or System.EventHandler<TEventArgs> b. MyEventHandlerType must take two parameters, the first of the type Object, and the second of a class derived from System.EventArgs c. MyEventHandlerType may have a non-void return type d. If MyEventHandlerType is a generic type, event declaration must use a specialization of that type. e. MyEventHandlerType cannot be declared static 4. Which of the following statements apply to developing .NET code, using .NET utilities that are available with the SDK or Visual Studio? a. Developers can create assemblies directly from the MSIL Source Code. b. Developers can examine PE header information in an assembly. c. Developers can generate XML Schemas from class definitions contained within an assembly. d. Developers can strip all meta-data from managed assemblies. e. Developers can split an assembly into multiple assemblies. 5. Which of the following characteristics do classes in the System.Drawing namespace such as Brush,Font,Pen, and Icon share? a. They encapsulate native resource and must be properly Disposed to prevent potential exhausting of resources. b. They are all MarshalByRef derived classes, but functionality across AppDomains has specific limitations. c. You can inherit from these classes to provide enhanced or customized functionality 6. Which of the following are required to be true by objects which are going to be used as keys in a System.Collections.HashTable? a. They must handle case-sensitivity identically in both the GetHashCode() and Equals() methods. b. Key objects must be immutable for the duration they are used within a HashTable. c. Get HashCode() must be overridden to provide the same result, given the same parameters, regardless of reference equalityl unless the HashTable constructor is provided with an IEqualityComparer parameter. d. Each Element in a HashTable is stored as a Key/Value pair of the type System.Collections.DictionaryElement e. All of the above 7. Which of the following are true about Nullable types? a. A Nullable type is a reference type. b. A Nullable type is a structure. c. An implicit conversion exists from any non-nullable value type to a nullable form of that type. d. An implicit conversion exists from any nullable value type to a non-nullable form of that type. e. A predefined conversion from the nullable type S? to the nullable type T? exists if there is a predefined conversion from the non-nullable type S to the non-nullable type T 8. When using an automatic property, which of the following statements is true? a. The compiler generates a backing field that is completely inaccessible from the application code. b. The compiler generates a backing field that is a private instance member with a leading underscore that can be programmatically referenced. c. The compiler generates a backing field that is accessible via reflection d. The compiler generates a code that will store the information separately from the instance to ensure its security. 9. Which of the following does using Initializer Syntax with a collection as shown below require? CollectionClass numbers = new CollectionClass { 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 }; a. The Collection Class must implement System.Collections.Generic.ICollection<T> b. The Collection Class must implement System.Collections.Generic.IList<T> c. Each of the Items in the Initializer List will be passed to the Add<T>(T item) method d. The items in the initializer will be treated as an IEnumerable<T> and passed to the collection constructor+K110 10. What impact will using implicitly typed local variables as in the following example have? var sample = "Hello World"; a. The actual type is determined at compilation time, and has no impact on the runtime b. The actual type is determined at runtime, and late binding takes effect c. The actual type is based on the native VARIANT concept, and no binding to a specific type takes place. d. "var" itself is a specific type defined by the framework, and no special binding takes place 11. Which of the following is not supported by remoting object types? a. well-known singleton b. well-known single call c. client activated d. context-agile 12. In which of the following ways do structs differ from classes? a. Structs can not implement interfaces b. Structs cannot inherit from a base struct c. Structs cannot have events interfaces d. Structs cannot have virtual methods 13. Which of the following is not an unboxing conversion? a. void Sample1(object o) { int i = (int)o; } b. void Sample1(ValueType vt) { int i = (int)vt; } c. enum E { Hello, World} void Sample1(System.Enum et) { E e = (E) et; } d. interface I { int Value { get; set; } } void Sample1(I vt) { int i = vt.Value; } e. class C { public int Value { get; set; } } void Sample1(C vt) { int i = vt.Value; } 14. Which of the following are characteristics of the System.Threading.Timer class? a. The method provided by the TimerCallback delegate will always be invoked on the thread which created the timer. b. The thread which creates the timer must have a message processing loop (i.e. be considered a UI thread) c. The class contains protection to prevent reentrancy to the method provided by the TimerCallback delegate d. You can receive notification of an instance being Disposed by calling an overload of the Dispose method. 15. What is the proper declaration of a method which will handle the following event? Class MyClass { public event EventHandler MyEvent; } a. public void A_MyEvent(object sender, MyArgs e) { } b. public void A_MyEvent(object sender, EventArgs e) { } c. public void A_MyEvent(MyArgs e) { } d. public void A_MyEvent(MyClass sender,EventArgs e) { } 16. Which of the following scenarios are applicable to Window Workflow Foundation? a. Document-centric workflows b. Human workflows c. User-interface page flows d. Builtin support for communications across multiple applications and/or platforms e. All of the above 17. When using an automatic property, which of the following statements is true? a. The compiler generates a backing field that is completely inaccessible from the application code. b. The compiler generates a backing field that is a private instance member with a leading underscore that can be programmatically referenced. c. The compiler generates a backing field that is accessible via reflection d. The compiler generates a code that will store the information separately from the instance to ensure its security. 18 While using the capabilities supplied by the System.Messaging classes, which of the following are true? a. Information must be explicitly converted to/from a byte stream before it uses the MessageQueue class b. Invoking the MessageQueue.Send member defaults to using the System.Messaging.XmlMessageFormatter to serialize the object. c. Objects must be XMLSerializable in order to be transferred over a MessageQueue instance. d. The first entry in a MessageQueue must be removed from the queue before the next entry can be accessed e. Entries removed from a MessageQueue within the scope of a transaction, will be pushed back into the front of the queue if the transaction fails. 19. Which of the following are true about declarative attributes? a. They must be inherited from the System.Attribute. b. Attributes are instantiated at the same time as instances of the class to which they are applied. c. Attribute classes may be restricted to be applied only to application element types. d. By default, a given attribute may be applied multiple times to the same application element. 20. When using version 3.5 of the framework in applications which emit a dynamic code, which of the following are true? a. A Partial trust code can not emit and execute a code b. A Partial trust application must have the SecurityCriticalAttribute attribute have called Assert ReflectionEmit permission c. The generated code no more permissions than the assembly which emitted it. d. It can be executed by calling System.Reflection.Emit.DynamicMethod( string name, Type returnType, Type[] parameterTypes ) without any special permissions Within Windows Workflow Foundation, Compensating Actions are used for: a. provide a means to rollback a failed transaction b. provide a means to undo a successfully committed transaction later c. provide a means to terminate an in process transaction d. achieve load balancing by adapting to the current activity 21. What is the proper declaration of a method which will handle the following event? Class MyClass { public event EventHandler MyEvent; } a. public void A_MyEvent(object sender, MyArgs e) { } b. public void A_MyEvent(object sender, EventArgs e) { } c. public void A_MyEvent(MyArgs e) { } d. public void A_MyEvent(MyClass sender,EventArgs e) { } 22. Which of the following controls allows the use of XSL to transform XML content into formatted content? a. System.Web.UI.WebControls.Xml b. System.Web.UI.WebControls.Xslt c. System.Web.UI.WebControls.Substitution d. System.Web.UI.WebControls.Transform 23. To which of the following do automatic properties refer? a. You declare (explicitly or implicitly) the accessibility of the property and get and set accessors, but do not provide any implementation or backing field b. You attribute a member field so that the compiler will generate get and set accessors c. The compiler creates properties for your class based on class level attributes d. They are properties which are automatically invoked as part of the object construction process 24. Which of the following are true about Nullable types? a. A Nullable type is a reference type. b. An implicit conversion exists from any non-nullable value type to a nullable form of that type. c. A predefined conversion from the nullable type S? to the nullable type T? exists if there is a predefined conversion from the non-nullable type S to the non-nullable type T 25. When using an automatic property, which of the following statements is true? a. The compiler generates a backing field that is completely inaccessible from the application code. b. The compiler generates a backing field that is accessible via reflection. c. The compiler generates a code that will store the information separately from the instance to ensure its security. 26. When using an implicitly typed array, which of the following is most appropriate? a. All elements in the initializer list must be of the same type. b. All elements in the initializer list must be implicitly convertible to a known type which is the actual type of at least one member in the initializer list c. All elements in the initializer list must be implicitly convertible to common type which is a base type of the items actually in the list 27. Which of the following is false about anonymous types? a. They can be derived from any reference type. b. Two anonymous types with the same named parameters in the same order declared in different classes have the same type. c. All properties of an anonymous type are read/write. 28. Which of the following are true about Extension methods. a. They can be declared either static or instance members b. They must be declared in the same assembly (but may be in different source files) c. Extension methods can be used to override existing instance methods d. Extension methods with the same signature for the same class may be declared in multiple namespaces without causing compilation errors

  Read the article

• Log4Net with ASP.NET MVC...nothing happens...

  - by twal

  I am trying to use log4Net with Asp.net MVC and I cannot get anything to happen with it. i created a config that is in my web project root. Here is that config file. <log4net> <root> <level value="INFO" /> <appender-ref ref="RollingLogFileAppender"/> </root> <appender name="RollingFileAppender" type="log4net.Appender.RollingFileAppender"> <file value="C:\DWSApplicationFiles\AppLogs\app.log" /> <appendToFile value="true" /> <rollingStyle value="Size" /> <maxSizeRollBackups value="10" /> <maximumFileSize value="100KB" /> <staticLogFileName value="true" /> <layout type="log4net.Layout.PatternLayout"> <conversionPattern value="%d [%t]%-5p %c [%x] - %m%n" /> </layout> </appender> <appender name="RollingLogFileAppender" type="log4net.Appender.RollingFileAppender"> <file value="C:\DWSApplicationFiles\AppLogs\app.log" /> <appendToFile value="false" /> <datePattern value="-dddd" /> <rollingStyle value="Date" /> <layout type="log4net.Layout.PatternLayout"> <conversionPattern value="%d [%t]%-5p %c [%x] - %m%n" /> </layout> </appender> </log4net> Before I am asked, yes the application has permissions to write to the directory. I use have tested this and the application has permissions to this directoy. here is where I am trying to use log4net. public class HomeController : Controller { readonly log4net.ILog log = log4net.LogManager.GetLogger(System.Reflection.MethodBase.GetCurrentMethod().DeclaringType); public ActionResult Index() { log.Error("In Index "); return View(); } } when I run the appliction and go to this controller. Log4net does nothing. it doesn't create the files in that directory or anything. I have enabled internal debugging for lognet and I get no output errors in the console. This is all i see from log4net log4net: log4net assembly [log4net, Version=1.2.10.0, Culture=neutral, PublicKeyToken=1b44e1d426115821]. Loaded from [C:\Users\twaldron.BULLFROGSPAS\AppData\Local\Temp\Temporary ASP.NET Files\root\7642c99a\60feb7f2\assembly\dl3\17247033\008dfd6d_e2d0ca01\log4net.DLL]. (.NET Runtime [2.0.50727.4952] on Microsoft Windows NT 6.1.7600.0) log4net: DefaultRepositorySelector: defaultRepositoryType [log4net.Repository.Hierarchy.Hierarchy] log4net: DefaultRepositorySelector: Creating repository for assembly [Bullfrog.DWS.Web, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null] log4net: DefaultRepositorySelector: Assembly [Bullfrog.DWS.Web, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null] Loaded From [C:\Users\twaldron.BULLFROGSPAS\AppData\Local\Temp\Temporary ASP.NET Files\root\7642c99a\60feb7f2\assembly\dl3\2960c79f\b876bb2d_aca7cb01\Bullfrog.DWS.Web.DLL] log4net: DefaultRepositorySelector: Assembly [Bullfrog.DWS.Web, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null] does not have a RepositoryAttribute specified. log4net: DefaultRepositorySelector: Assembly [Bullfrog.DWS.Web, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null] using repository [log4net-default-repository] and repository type [log4net.Repository.Hierarchy.Hierarchy] log4net: DefaultRepositorySelector: Creating repository [log4net-default-repository] using type [log4net.Repository.Hierarchy.Hierarchy] 'WebDev.WebServer20.EXE' (Managed (v2.0.50727)): Loaded 'Anonymously Hosted DynamicMethods Assembly'

  Read the article

• protobuf-net: incorrect wire-type exception deserializing Guid properties

  - by Paul Smith

  I'm having issues deserializing certain Guid properties of ORM-generated entities using protobuf-net. Here's a simplified example of the code (reproduces most elements of the scenario, but doesn't reproduce the behavior; I can't expose our internal entities, so I'm looking for clues to account for the exception). Say I have a class, Account with an AccountID read-only guid, and an AccountName read-write string. I serialize & immediately deserialize a clone. Deserializing throws an Incorrect wire-type deserializing Guid exception while deserializing. Here's example usage... Account acct = new Account() { AccountName = "Bob's Checking" }; Debug.WriteLine(acct.AccountID.ToString()); using (MemoryStream ms = new MemoryStream()) { ProtoBuf.Serializer.Serialize<Account>(ms, acct); Debug.WriteLine(Encoding.UTF8.GetString(ms.GetBuffer())); ms.Position = 0; Account clone = ProtoBuf.Serializer.Deserialize<Account>(ms); Debug.WriteLine(clone.AccountID.ToString()); } And here's an example ORM'd class (simplified, but demonstrates the relevant semantics I can think of). Uses a shell game to deserialize read-only properties by exposing the backing field ("can't write" essentially becomes "shouldn't write," but we can scan code for instances of assigning to these fields, so the hack works for our purposes). Again, this does not reproduce the exception behavior; I'm looking for clues as to what could: [DataContract()] [Serializable()] public partial class Account { public Account() { _accountID = Guid.NewGuid(); } [XmlAttribute("AccountID")] [DataMember(Name = "AccountID", Order = 1)] public Guid _accountID; /// <summary> /// A read-only property; XML, JSON and DataContract serializers all seem /// to correctly recognize the public backing field when deserializing: /// </summary> [IgnoreDataMember] [XmlIgnore] public Guid AccountID { get { return this._accountID; } } [IgnoreDataMember] protected string _accountName; [DataMember(Name = "AccountName", Order = 2)] [XmlAttribute] public string AccountName { get { return this._accountName; } set { this._accountName = value; } } } XML, JSON and DataContract serializers all seem to serialize / deserialize these object graphs just fine, so the attribute arrangement basically works. I've tried protobuf-net with lists vs. single instances, different prefix styles, etc., but still always get the 'incorrect wire-type ... Guid' exception when deserializing. So the specific questions is, is there any known explanation / workaround for this? I'm at a loss trying to trace what circumstances (in the real code but not the example) could be causing it. We hope not to have to create a protobuf dependency directly in the entity layer; if that's the case, we'll probably create proxy DTO entities with all public properties having protobuf attributes. (This is a subjective issue I have with all declarative serialization models; it's a ubiquitous pattern & I understand why it arose, but IMO, if we can put a man on the moon, then "normal" should be to have objects and serialization contracts decoupled. ;-) ) Thanks!

  Read the article

• FluentNHibernate Unit Of Work / Repository Design Pattern Questions

  - by Echiban

  Hi all, I think I am at a impasse here. I have an application I built from scratch using FluentNHibernate (ORM) / SQLite (file db). I have decided to implement the Unit of Work and Repository Design pattern. I am at a point where I need to think about the end game, which will start as a WPF windows app (using MVVM) and eventually implement web services / ASP.Net as UI. Now I already created domain objects (entities) for ORM. And now I don't know how should I use it outside of ORM. Questions about it include: Should I use ORM entity objects directly as models in MVVM? If yes, do I put business logic (such as certain values must be positive and be greater than another Property) in those entity objects? It is certainly the simpler approach, and one I am leaning right now. However, will there be gotchas that would trash this plan? If the answer above is no, do I then create a new set of classes to implement business logic and use those as Models in MVVM? How would I deal with the transition between model objects and entity objects? I guess a type converter implementation would work well here. Now I followed this well written article to implement the Unit Of Work pattern. However, due to the fact that I am using FluentNHibernate instead of NHibernate, I had to bastardize the implementation of UnitOfWorkFactory. Here's my implementation: using System; using FluentNHibernate.Cfg; using FluentNHibernate.Cfg.Db; using NHibernate; using NHibernate.Cfg; using NHibernate.Tool.hbm2ddl; namespace ELau.BlindsManagement.Business { public class UnitOfWorkFactory : IUnitOfWorkFactory { private static readonly string DbFilename; private static Configuration _configuration; private static ISession _currentSession; private ISessionFactory _sessionFactory; static UnitOfWorkFactory() { // arbitrary default filename DbFilename = "defaultBlindsDb.db3"; } internal UnitOfWorkFactory() { } #region IUnitOfWorkFactory Members public ISession CurrentSession { get { if (_currentSession == null) { throw new InvalidOperationException(ExceptionStringTable.Generic_NotInUnitOfWork); } return _currentSession; } set { _currentSession = value; } } public ISessionFactory SessionFactory { get { if (_sessionFactory == null) { _sessionFactory = BuildSessionFactory(); } return _sessionFactory; } } public Configuration Configuration { get { if (_configuration == null) { Fluently.Configure().ExposeConfiguration(c => _configuration = c); } return _configuration; } } public IUnitOfWork Create() { ISession session = CreateSession(); session.FlushMode = FlushMode.Commit; _currentSession = session; return new UnitOfWorkImplementor(this, session); } public void DisposeUnitOfWork(UnitOfWorkImplementor adapter) { CurrentSession = null; UnitOfWork.DisposeUnitOfWork(adapter); } #endregion public ISession CreateSession() { return SessionFactory.OpenSession(); } public IStatelessSession CreateStatelessSession() { return SessionFactory.OpenStatelessSession(); } private static ISessionFactory BuildSessionFactory() { ISessionFactory result = Fluently.Configure() .Database( SQLiteConfiguration.Standard .UsingFile(DbFilename) ) .Mappings(m => m.FluentMappings.AddFromAssemblyOf<UnitOfWorkFactory>()) .ExposeConfiguration(BuildSchema) .BuildSessionFactory(); return result; } private static void BuildSchema(Configuration config) { // this NHibernate tool takes a configuration (with mapping info in) // and exports a database schema from it _configuration = config; new SchemaExport(_configuration).Create(false, true); } } } I know that this implementation is flawed because a few tests pass when run individually, but when all tests are run, it would fail for some unknown reason. Whoever wants to help me out with this one, given its complexity, please contact me by private message. I am willing to send some $$$ by Paypal to someone who can address the issue and provide solid explanation. I am new to ORM, so any assistance is appreciated.

  Read the article

• WCF MustUnderstand headers are not understood

  - by raghur

  Hello everyone, I am using a Java Web Service which is developed by one of our vendor which I really do not have any control over it. I have written a WCF router which the client application calls it and the router sends the message to the Java Web Service and returns the data back to the client. The issue what I am encountering is, I am successfully able to call the Java web service from the WCF router, but, I am getting the following exceptions back. Router config file is as follows: <customBinding> <binding name="SimpleWSPortBinding"> <!--<reliableSession maxPendingChannels="4" maxRetryCount="8" ordered="true" />--> <!--<mtomMessageEncoding messageVersion ="Soap12WSAddressing10" ></mtomMessageEncoding>--> <textMessageEncoding maxReadPoolSize="64" maxWritePoolSize="16" messageVersion="Soap12WSAddressing10" writeEncoding="utf-8" /> <httpTransport manualAddressing="false" maxBufferPoolSize="524288" maxReceivedMessageSize="65536" allowCookies="false" authenticationScheme="Anonymous" bypassProxyOnLocal="true" keepAliveEnabled="true" maxBufferSize="65536" transferMode="Buffered" unsafeConnectionNtlmAuthentication="false"/> </binding> </customBinding> Test client config file <customBinding> <binding name="DocumentRepository_Binding_Soap12"> <!--<reliableSession maxPendingChannels="4" maxRetryCount="8" ordered="true" />--> <!--<mtomMessageEncoding messageVersion ="Soap12WSAddressing10" ></mtomMessageEncoding>--> <textMessageEncoding maxReadPoolSize="64" maxWritePoolSize="16" messageVersion="Soap12WSAddressing10" writeEncoding="utf-8"> <readerQuotas maxDepth="32" maxStringContentLength="8192" maxArrayLength="16384" maxBytesPerRead="4096" maxNameTableCharCount="16384" /> </textMessageEncoding> <httpTransport manualAddressing="false" maxBufferPoolSize="524288" maxReceivedMessageSize="65536" allowCookies="false" authenticationScheme="Anonymous" bypassProxyOnLocal="false" hostNameComparisonMode="StrongWildcard" keepAliveEnabled="true" maxBufferSize="65536" proxyAuthenticationScheme="Anonymous" realm="" transferMode="Buffered" unsafeConnectionNtlmAuthentication="false" useDefaultWebProxy="true" /> </binding> </customBinding> If I use the textMessageEncoding I am getting <soap:Text xml:lang="en">MustUnderstand headers: [{http://www.w3.org/2005/08/addressing}To, {http://www.w3.org/2005/08/addressing}Action] are not understood.</soap:Text> If I use mtomMessageEncoding I am getting The server did not provide a meaningful reply; this might be caused by a contract mismatch, a premature session shutdown or an internal server error. My Router class is as follows: [ServiceBehavior(InstanceContextMode = InstanceContextMode.Single, ConcurrencyMode = ConcurrencyMode.Multiple, AddressFilterMode = AddressFilterMode.Any, ValidateMustUnderstand = false)] public class EmployeeService : IEmployeeService { public System.ServiceModel.Channels.Message ProcessMessage(System.ServiceModel.Channels.Message requestMessage) { ChannelFactory<IEmployeeService> factory = new ChannelFactory<IEmployeeService>("client"); factory.Endpoint.Behaviors.Add(new MustUnderstandBehavior(false)); IEmployeeService proxy = factory.CreateChannel(); Message responseMessage = proxy.ProcessMessage(requestMessage); return responseMessage; } } The "client" in the above code under ChannelFactory is defined in the config file as: <client> <endpoint address="http://JavaWS/EmployeeService" binding="wsHttpBinding" bindingConfiguration="wsHttp" contract="EmployeeService.IEmployeeService" name="client" behaviorConfiguration="clientBehavior"> <headers> </headers> </endpoint> </client> Really appreciate your kind help. Thanks in advance, Raghu

  Read the article

• Can't view order in magento

  - by koko

  Hi, I've been setting up a fresh magento 1.4.0.1 install, working great so far. I did some test orders just to see. Everything works fine, but when I click on "view order" under "my orders", I get a bunch of error messages: There has been an error processing your request Notice: iconv_substr() [function.iconv-substr]: Unknown error (0) in /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Helper/String.php on line 98 Trace: #0 [internal function]: mageCoreErrorHandler(8, 'iconv_substr() ...', '/data/web/A1423...', 98, Array) #1 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Helper/String.php(98): iconv_substr('1', 0, 50, 'UTF-8') #2 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Helper/String.php(173): Mage_Core_Helper_String-substr('1', 0, 50) #3 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Helper/String.php(112): Mage_Core_Helper_String-str_split('1', 50) #4 /data/web/A14237/htdocs/magento/app/design/frontend/base/default/template/sales/order/items/renderer/default.phtml(58): Mage_Core_Helper_String-splitInjection('1') #5 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(189): include('/data/web/A1423...') #6 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(225): Mage_Core_Block_Template-fetchView('frontend/base/d...') #7 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(242): Mage_Core_Block_Template-renderView() #8 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Core_Block_Template-_toHtml() #9 /data/web/A14237/htdocs/magento/app/code/core/Mage/Sales/Block/Items/Abstract.php(137): Mage_Core_Block_Abstract-toHtml() #10 /data/web/A14237/htdocs/magento/app/design/frontend/base/default/template/sales/order/items.phtml(52): Mage_Sales_Block_Items_Abstract-getItemHtml(Object(Mage_Sales_Model_Order_Item)) #11 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(189): include('/data/web/A1423...') #12 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(225): Mage_Core_Block_Template-fetchView('frontend/base/d...') #13 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(242): Mage_Core_Block_Template-renderView() #14 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Core_Block_Template-_toHtml() #15 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(516): Mage_Core_Block_Abstract-toHtml() #16 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(467): Mage_Core_Block_Abstract-_getChildHtml('order_items', true) #17 /data/web/A14237/htdocs/magento/app/design/frontend/base/default/template/sales/order/view.phtml(64): Mage_Core_Block_Abstract-getChildHtml('order_items') #18 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(189): include('/data/web/A1423...') #19 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(225): Mage_Core_Block_Template-fetchView('frontend/base/d...') #20 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(242): Mage_Core_Block_Template-renderView() #21 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Core_Block_Template-_toHtml() #22 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(516): Mage_Core_Block_Abstract-toHtml() #23 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(463): Mage_Core_Block_Abstract-_getChildHtml('sales.order.vie...', true) #24 /data/web/A14237/htdocs/magento/app/code/core/Mage/Page/Block/Html/Wrapper.php(52): Mage_Core_Block_Abstract-getChildHtml('', true, true) #25 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Page_Block_Html_Wrapper-_toHtml() #26 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Text/List.php(43): Mage_Core_Block_Abstract-toHtml() #27 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Core_Block_Text_List-_toHtml() #28 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(516): Mage_Core_Block_Abstract-toHtml() #29 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(467): Mage_Core_Block_Abstract-_getChildHtml('content', true) #30 /data/web/A14237/htdocs/magento/app/design/frontend/base/default/template/page/2columns-left.phtml(48): Mage_Core_Block_Abstract-getChildHtml('content') #31 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(189): include('/data/web/A1423...') #32 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(225): Mage_Core_Block_Template-fetchView('frontend/base/d...') #33 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(242): Mage_Core_Block_Template-renderView() #34 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Core_Block_Template-_toHtml() #35 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Model/Layout.php(536): Mage_Core_Block_Abstract-toHtml() #36 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Controller/Varien/Action.php(389): Mage_Core_Model_Layout-getOutput() #37 /data/web/A14237/htdocs/magento/app/code/core/Mage/Sales/controllers/OrderController.php(100): Mage_Core_Controller_Varien_Action-renderLayout() #38 /data/web/A14237/htdocs/magento/app/code/core/Mage/Sales/controllers/OrderController.php(136): Mage_Sales_OrderController-_viewAction() #39 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Controller/Varien/Action.php(418): Mage_Sales_OrderController-viewAction() #40 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Controller/Varien/Router/Standard.php(254): Mage_Core_Controller_Varien_Action-dispatch('view') #41 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Controller/Varien/Front.php(177): Mage_Core_Controller_Varien_Router_Standard-match(Object(Mage_Core_Controller_Request_Http)) #42 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Model/App.php(304): Mage_Core_Controller_Varien_Front-dispatch() #43 /data/web/A14237/htdocs/magento/app/Mage.php(596): Mage_Core_Model_App-run(Array) #44 /data/web/A14237/htdocs/magento/index.php(78): Mage::run('', 'store') #45 {main} gtx, koko

  Read the article

• cmake doesn't work in windows XP

  - by Runner

  I'm new with cmake,just installed it and following this article: http://www.cs.swarthmore.edu/~adanner/tips/cmake.php D:\Works\c\cmake\build>cmake .. -- Building for: NMake Makefiles CMake Warning at CMakeLists.txt:2 (project): To use the NMake generator, cmake must be run from a shell that can use the compiler cl from the command line. This environment does not contain INCLUDE, LIB, or LIBPATH, and these must be set for the cl compiler to work. -- The C compiler identification is unknown -- The CXX compiler identification is unknown CMake Warning at D:/Tools/CMake 2.8/share/cmake-2.8/Modules/Platform/Windows-cl.cmake:32 (ENABLE_LANGUAGE): To use the NMake generator, cmake must be run from a shell that can use the compiler cl from the command line. This environment does not contain INCLUDE, LIB, or LIBPATH, and these must be set for the cl compiler to work. Call Stack (most recent call first): D:/Tools/CMake 2.8/share/cmake-2.8/Modules/CMakeCInformation.cmake:58 (INCLUDE) CMakeLists.txt:2 (project) CMake Error: your RC compiler: "CMAKE_RC_COMPILER-NOTFOUND" was not found. Please set CMAKE_RC_COMPILER to a valid compiler path or name. -- Check for CL compiler version -- Check for CL compiler version - failed -- Check if this is a free VC compiler -- Check if this is a free VC compiler - yes -- Using FREE VC TOOLS, NO DEBUG available -- Check for working C compiler: cl CMake Warning at CMakeLists.txt:2 (PROJECT): To use the NMake generator, cmake must be run from a shell that can use the compiler cl from the command line. This environment does not contain INCLUDE, LIB, or LIBPATH, and these must be set for the cl compiler to work. CMake Warning at D:/Tools/CMake 2.8/share/cmake-2.8/Modules/Platform/Windows-cl.cmake:32 (ENABLE_LANGUAGE): To use the NMake generator, cmake must be run from a shell that can use the compiler cl from the command line. This environment does not contain INCLUDE, LIB, or LIBPATH, and these must be set for the cl compiler to work. Call Stack (most recent call first): D:/Tools/CMake 2.8/share/cmake-2.8/Modules/CMakeCInformation.cmake:58 (INCLUDE) CMakeLists.txt:2 (PROJECT) CMake Error at D:/Tools/CMake 2.8/share/cmake-2.8/Modules/CMakeRCInformation.cmake:22 (GET_FILENAME_COMPONENT): get_filename_component called with incorrect number of arguments Call Stack (most recent call first): D:/Tools/CMake 2.8/share/cmake-2.8/Modules/Platform/Windows-cl.cmake:32 (ENABLE_LANGUAGE) D:/Tools/CMake 2.8/share/cmake-2.8/Modules/CMakeCInformation.cmake:58 (INCLUDE) CMakeLists.txt:2 (PROJECT) CMake Error: CMAKE_RC_COMPILER not set, after EnableLanguage CMake Error: your C compiler: "cl" was not found. Please set CMAKE_C_COMPILER to a valid compiler path or name. CMake Error: Internal CMake error, TryCompile configure of cmake failed -- Check for working C compiler: cl -- broken CMake Error at D:/Tools/CMake 2.8/share/cmake-2.8/Modules/CMakeTestCCompiler.cmake:52 (MESSAGE): The C compiler "cl" is not able to compile a simple test program. It fails with the following output: CMake will not be able to correctly generate this project. Call Stack (most recent call first): CMakeLists.txt:2 (project) CMake Error: your C compiler: "cl" was not found. Please set CMAKE_C_COMPILER to a valid compiler path or name. CMake Error: your CXX compiler: "cl" was not found. Please set CMAKE_CXX_COMPILER to a valid compiler path or name. -- Configuring incomplete, errors occurred! What are the complete requirement to use cmake successfully in windows XP?I've already installed Visual Studio under D:\Tools\Microsoft Visual Studio 9.0

  Read the article

• Inconsistent responses from ISAPI DLL in mod_isapi.

  - by William Leader

  I have a ISAPI dll which I created with Delphi 2009, and I have been able to test that it functions as designed when I run it inside of IIS 5.1. However when I attempt to host the web service from within Apache on Windows XP using mod_isapi, I do not get consistent results. The ISAPI dll implements a very simple SOAP service with two methods. One method is a simple echo service that sends back the string sent to it. The second method is used to send a file to the server using a TSoapAttachement (Mutipart MIME). The interface can be descibes as follows IPdiSvc2 = interface(IInvokable) ['{532DCDD7-D66B-4D2C-924E-2F389D3E0A74}'] function Echo(data:string): string; stdcall; function SendFile(request:TFileDescription; attachment: TSOAPAttachment): TSendFileResponse; stdcall; end; What is interesting is if I only call the echo function Apache handles this without error every time. The webservice only returns an error after calling send File, but not every time. There are three outcomes to calling send file that I have observed: A normal result without an error (HTTP 200 OK). A Soap encoded exception with the message: 'Required white space was missing. Line: 11 <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML.' (HTTP 500 Internal Error). This also generates a message in the Apache error.log 'Premature end of script headers: MYISAPI.dll' A Soap encoded exception with the message: 'Access violation at address 01A53D57 in module MYISAPI.dll. Read of address 00000000.' (HTTP 200 OK). What I find interesting is that the second third outcomes still occur if I call echo after calling send file. Calling SendFile, SendFile, SendFile, SendFile results in outcomes 1, 2, 3, 1. Calling Echo, SendFile, SendFile, SendFile results in outcomes 1, 1, 2, 3. Calling SendFile, Echo, Echo, SendFile results in outcomes 1, 2, 3, 1. The pattern I am seing is that after a Successful SendFile, the next to requests result in outcomes 2 and 3 regardless of what those two requests are. My guess is that because Apache uses multiple threads to handle multiple requests that each request is getting handled in a slightly different way, and that the DLL may not have been initialized in the same way for each worker thread. I do not think the problem exists in my code as when I attach the debugger to httpd.exe it does recognize the exceptions but it says the exceptions are in non-delphi code meaning that they are happening before the code inside my DLL has a chance to execute. I suspect it may have something to do with the way I have apache configured. My Apache configuration is the defaults created by the 2.2.15 installer for windows with the following addition: <IfModule isapi_module> AddHandler isapi-handler .dll ISAPILogNotSupported on ISAPIFakeAsync on ISAPIAppendLogToErrors on </IfModule> <IfModule alias_module> ScriptAlias /myisapi/ "C:/path/to/myisapi/" </IfModule> <Directory "C:/path/to/myisapi/"> AllowOverride None Options ExecCGI Order allow,deny Allow from all </Directory>

  Read the article

< Previous Page | 287 288 289 290 291 292 293 294 295 296 297 298  | Next Page >