Search Results

Search found 16947 results on 678 pages for 'kernel programming'.

Page 292/678 | < Previous Page | 288 289 290 291 292 293 294 295 296 297 298 299  | Next Page >

• TPROXY Not working with HAProxy, Ubuntu 14.04

  - by Nyxynyx

  I'm trying to use HAProxy as a fully transparent proxy using TPROXY in Ubuntu 14.04. HAProxy will be setup on the first server with eth1 111.111.250.250 and eth0 10.111.128.134. The single balanced server has eth1 and eth0 as well. eth1 is the public facing network interface while eth0 is for the private network which both servers are in. Problem: I'm able to connect to the balanced server's port 1234 directly (via eth1) but am not able to reach the balanced server via Haproxy port 1234 (which redirects to 1234 via eth0). Am I missing out something in this configuration? On the HAProxy server The current kernel is: Linux extremehash-lb2 3.13.0-24-generic #46-Ubuntu SMP Thu Apr 10 19:11:08 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux The kernel appears to have TPROXY support: # grep TPROXY /boot/config-3.13.0-24-generic CONFIG_NETFILTER_XT_TARGET_TPROXY=m HAProxy was compiled with TPROXY support: haproxy -vv HA-Proxy version 1.5.3 2014/07/25 Copyright 2000-2014 Willy Tarreau <[email protected]> Build options : TARGET = linux26 CPU = x86_64 CC = gcc CFLAGS = -g -fno-strict-aliasing OPTIONS = USE_LINUX_TPROXY=1 USE_LIBCRYPT=1 USE_STATIC_PCRE=1 Default settings : maxconn = 2000, bufsize = 16384, maxrewrite = 8192, maxpollevents = 200 Encrypted password support via crypt(3): yes Built without zlib support (USE_ZLIB not set) Compression algorithms supported : identity Built without OpenSSL support (USE_OPENSSL not set) Built with PCRE version : 8.31 2012-07-06 PCRE library supports JIT : no (USE_PCRE_JIT not set) Built with transparent proxy support using: IP_TRANSPARENT IPV6_TRANSPARENT IP_FREEBIND Available polling systems : epoll : pref=300, test result OK poll : pref=200, test result OK select : pref=150, test result OK Total: 3 (3 usable), will use epoll. In /etc/haproxy/haproxy.cfg, I've configured a port to have the following options: listen test1235 :1234 mode tcp option tcplog balance leastconn source 0.0.0.0 usesrc clientip server balanced1 10.111.163.76:1234 check inter 5s rise 2 fall 4 weight 4 On the balanced server In /etc/networking/interfaces I've set the gateway for eth0 to be the HAProxy box 10.111.128.134 and restarted networking. auto eth0 eth1 iface eth0 inet static address 111.111.250.250 netmask 255.255.224.0 gateway 111.131.224.1 dns-nameservers 8.8.4.4 8.8.8.8 209.244.0.3 iface eth1 inet static address 10.111.163.76 netmask 255.255.0.0 gateway 10.111.128.134 ip route gives: default via 111.111.224.1 dev eth0 10.111.0.0/16 dev eth1 proto kernel scope link src 10.111.163.76 111.111.224.0/19 dev eth0 proto kernel scope link src 111.111.250.250

  Read the article

• Help with Windows 7 BSOD with windbg minidump !analyze -v results

  - by Kurt Harless

  Hi gang, Windows 7 X64 Ultimate is BSODing occasionally. I suspect an overheating issue or something related to the use of my GTX-295 card that runs very hot. Here is an !analyze -v listing of the most recent minidump. Any and all help greatly appreciated. Kurt Microsoft (R) Windows Debugger Version 6.12.0002.633 AMD64 Copyright (c) Microsoft Corporation. All rights reserved. Loading Dump File [C:\Windows\Minidump\122810-31387-01.dmp] Mini Kernel Dump File: Only registers and stack trace are available Symbol search path is: SRV*c:\websymbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Kernel Version 7600 MP (8 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 7600.16617.amd64fre.win7_gdr.100618-1621 Machine Name: Kernel base = 0xfffff800`03065000 PsLoadedModuleList = 0xfffff800`032a2e50 Debug session time: Tue Dec 28 11:04:03.597 2010 (UTC - 7:00) System Uptime: 2 days 2:28:40.407 Loading Kernel Symbols ............................................................... ................................................................ .............................................. Loading User Symbols Loading unloaded module list ................ ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* Use !analyze -v to get detailed debugging information. BugCheck 3B, {c0000005, fffff800033b8873, fffff8800e322dc0, 0} Probably caused by : ntkrnlmp.exe ( nt!RtlCompareUnicodeStrings+c3 ) Followup: MachineOwner --------- 1: kd> !analyze -v ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* SYSTEM_SERVICE_EXCEPTION (3b) An exception happened while executing a system service routine. Arguments: Arg1: 00000000c0000005, Exception code that caused the bugcheck Arg2: fffff800033b8873, Address of the instruction which caused the bugcheck Arg3: fffff8800e322dc0, Address of the context record for the exception that caused the bugcheck Arg4: 0000000000000000, zero. Debugging Details: ------------------ EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s. FAULTING_IP: nt!RtlCompareUnicodeStrings+c3 fffff800`033b8873 488b7c2418 mov rdi,qword ptr [rsp+18h] CONTEXT: fffff8800e322dc0 -- (.cxr 0xfffff8800e322dc0) rax=0000000000000041 rbx=fffff8a015a3c1c0 rcx=0000000000000024 rdx=0000000000000003 rsi=fffff8800e3238b0 rdi=0000000000000009 rip=fffff800033b8873 rsp=fffff8800e323798 rbp=000000000000000d r8=fffff8a018cb374c r9=000000200a98fdc4 r10=fffff8800e323988 r11=fffff8800e32398e r12=fffff8a018127c18 r13=fffff8800126e550 r14=0000000000000001 r15=fffffa800abe1570 iopl=0 nv up ei pl nz ac po nc cs=0010 ss=0018 ds=002b es=002b fs=0053 gs=002b efl=00010216 nt!RtlCompareUnicodeStrings+0xc3: fffff800`033b8873 488b7c2418 mov rdi,qword ptr [rsp+18h] ss:0018:fffff880`0e3237b0=???????????????? Resetting default scope CUSTOMER_CRASH_COUNT: 1 DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT BUGCHECK_STR: 0x3B PROCESS_NAME: ccSvcHst.exe CURRENT_IRQL: 0 LAST_CONTROL_TRANSFER: from 0000000000000000 to fffff800033b8873 STACK_TEXT: fffff880`0e323798 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!RtlCompareUnicodeStrings+0xc3 FOLLOWUP_IP: nt!RtlCompareUnicodeStrings+c3 fffff800`033b8873 488b7c2418 mov rdi,qword ptr [rsp+18h] SYMBOL_STACK_INDEX: 0 SYMBOL_NAME: nt!RtlCompareUnicodeStrings+c3 FOLLOWUP_NAME: MachineOwner MODULE_NAME: nt IMAGE_NAME: ntkrnlmp.exe DEBUG_FLR_IMAGE_TIMESTAMP: 4c1c44a9 STACK_COMMAND: .cxr 0xfffff8800e322dc0 ; kb FAILURE_BUCKET_ID: X64_0x3B_nt!RtlCompareUnicodeStrings+c3 BUCKET_ID: X64_0x3B_nt!RtlCompareUnicodeStrings+c3 Followup: MachineOwner ---------

  Read the article

• New install indicator while install updating on Ubuntu

  - by Phuong Nguyen

  In the update manager of ubuntu I see several libraries marked with New Install. I don't know what is the benefit I can get from that New Install? What if I just want a normal upgrade, not a New Install? (I have 3 Linux Kernel versions right now (that I can see and select from Grub menu), and I think I don't need all of them since I always use the latest Kernel).

  Read the article

• Cannot exit X server, restart, shutdown or drop to tty when VGA monitor active

  - by terdon

  I have a strange problem. If I connect an external VGA monitor to my laptop, exiting the X environment in any way crashes the computer. For example, say I am working with my two monitors (the laptop's and one connected to my VGA port) active. Hitting Ctrl+Alt+F Key should take me down to a tty. What actually happens is that the VGA screen goes blank, as you would expect, but the laptop screen, although still on, shows nothing. I know the screen is on because it is slightly more illuminated than when it is off. When in this state, I can do nothing to regain access to the machine. I have tried: Ctrl+F Key (and even Ctrl+Alt+F Key, just in case) combinations and none seem to have any effect. Ctrl+Alt+Del : Nothing Magic SysRq key: Nothing Blindly typing my username and password and trying to reboot/shutdown or restart GDM or MDM: Nothing The only thing that works is a hard reset. The exact same behavior occurs when kiling the X server through Ctrl+Alt+Backspace, rebooting or shutdown. There is no difference if I reboot/shutdown/log out using the WM's graphical menu or if I use the shutdown or rebootcommands. It is also not WM-dependent. I have the same problem using Cinnamon, Gnome 3, MATE and xfce4. It is, however, VGA dependent. I have tried connecting another VGA monitor and have the same problem. I do not, however, have this problem if a screen is connected to the DisplayPort. It is, therefore, a VGA specific issue. To make things even stranger, this only occurs when both screens are active. If either the laptop screen or the VGA monitor is inactive the problem goes away. Finally, this problem arose when I installed the latest Linux Mint Debian (LMDE). It did not occur with the previous release of LMDE. I am not sure what has changed since I used the same kernel version in both releases (I had upgraded the kernel while on the previous release) and, I think, the same nvidia drivers. Oh, and yes, I have updated the nvidia driver. Hardware: Dell M4500 laptop CPU: Intel Core i7 RAM: 8GB Graphics: nVidia GT216 [Quadro FX 880M] Software: LMDE, kernel 3.2.0-2-amd64 Xorg: 1.11.4 nVidia kernel: 295.20-1+3.2.9-1 Possibly relevant files: /var/log/Xorg.0.log ~/.xsession-errors Does anyone have any ideas how to fix this? Thanks in advance for any help.

  Read the article

• EC2 instance suddenly refusing SSH connections and won't respond to ping

  - by Chris

  My instance was running fine and this morning I was able to access a Ruby on Rails app hosted on it. An hour later I suddenly wasn't able to access my site, my SSH connection attempts were refused and the server wasn't even responding to ping. I didn't change anything on my system during that hour and reboots aren't fixing it. I've never had any problems connecting or pinging the system before. Can someone please help? This is on my production system! OS: CentOS 5 AMI ID: ami-10b55379 Type: m1.small [] ~% ssh -v *****@meeteor.com OpenSSH_5.2p1, OpenSSL 0.9.8l 5 Nov 2009 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to meeteor.com [184.73.235.191] port 22. debug1: connect to address 184.73.235.191 port 22: Connection refused ssh: connect to host meeteor.com port 22: Connection refused [] ~% ping meeteor.com PING meeteor.com (184.73.235.191): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 ^C --- meeteor.com ping statistics --- 4 packets transmitted, 0 packets received, 100.0% packet loss [] ~% ========= System Log ========= Restarting system. Linux version 2.6.16-xenU ([email protected]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled Built 1 zonelists Kernel command line: root=/dev/sda1 ro 4 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Xen reported: 2599.998 MHz processor. Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Software IO TLB disabled vmalloc area: ee000000-f53fe000, maxmem 2d7fe000 Memory: 1718700k/1748992k available (1958k kernel code, 20948k reserved, 620k data, 144k init, 1003528k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5202.30 BogoMIPS (lpj=26011526) Mount-cache hash table entries: 512 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) Checking 'hlt' instruction... OK. Brought up 1 CPUs migration_cost=0 Grant table initialized NET: Registered protocol family 16 Brought up 1 CPUs xen_mem: Initialising balloon driver. highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered i8042.c: No controller found. RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Xen virtual console successfully installed as tty1 Event-channel device installed. netfront: Initialising virtual ethernet driver. mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 2 Registering block device major 8 IP route cache hash table entries: 65536 (order: 6, 262144 bytes) TCP established hash table entries: 262144 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Using IPI No-Shortcut mode md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 144k freed *************************************************************** *************************************************************** ** WARNING: Currently emulating unsupported memory accesses ** ** in /lib/tls glibc libraries. The emulation is ** ** slow. To ensure full performance you should ** ** install a 'xen-friendly' (nosegneg) version of ** ** the library, or disable tls support by executing ** ** the following as root: ** ** mv /lib/tls /lib/tls.disabled ** ** Offending process: init (pid=1) ** *************************************************************** *************************************************************** Pausing... 5Pausing... 4Pausing... 3Pausing... 2Pausing... 1Continuing... INIT: version 2.86 booting Welcome to CentOS release 5.4 (Final) Press 'I' to enter interactive startup. Setting clock : Fri Oct 1 14:35:26 EDT 2010 [ OK ] Starting udev: [ OK ] Setting hostname localhost.localdomain: [ OK ] No devices found Setting up Logical Volume Management: [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/sda1 /dev/sda1: clean, 275424/1310720 files, 1161123/2621440 blocks [ OK ] Remounting root filesystem in read-write mode: [ OK ] Mounting local filesystems: [ OK ] Enabling local filesystem quotas: [ OK ] Enabling /etc/fstab swaps: [ OK ] INIT: Entering runlevel: 4 Entering non-interactive startup Starting background readahead: [ OK ] Applying ip6tables firewall rules: modprobe: FATAL: Module ip6_tables not found. ip6tables-restore v1.3.5: ip6tables-restore: unable to initializetable 'filter' Error occurred at line: 3 Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more information. [FAILED] Applying iptables firewall rules: [ OK ] Loading additional iptables modules: ip_conntrack_netbios_ns [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... done. [ OK ] Starting auditd: [FAILED] Starting irqbalance: [ OK ] Starting portmap: [ OK ] FATAL: Module lockd not found. Starting NFS statd: [ OK ] Starting RPC idmapd: FATAL: Module sunrpc not found. FATAL: Error running install command for sunrpc Error: RPC MTAB does not exist. Starting system message bus: [ OK ] Starting Bluetooth services:[ OK ] [ OK ] Can't open RFCOMM control socket: Address family not supported by protocol Mounting other filesystems: [ OK ] Starting PC/SC smart card daemon (pcscd): [ OK ] Starting hidd: Can't open HIDP control socket: Address family not supported by protocol [FAILED] Starting autofs: Starting automount: automount: test mount forbidden or incorrect kernel protocol version, kernel protocol version 5.00 or above required. [FAILED] [FAILED] Starting sshd: [ OK ] Starting cups: [ OK ] Starting sendmail: [ OK ] Starting sm-client: [ OK ] Starting console mouse services: no console device found[FAILED] Starting crond: [ OK ] Starting xfs: [ OK ] Starting anacron: [ OK ] Starting atd: [ OK ] % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 390 100 390 0 0 58130 0 --:--:-- --:--:-- --:--:-- 58130 100 390 100 390 0 0 56984 0 --:--:-- --:--:-- --:--:-- 0 Starting yum-updatesd: [ OK ] Starting Avahi daemon... [ OK ] Starting HAL daemon: [ OK ] Starting OSSEC: [ OK ] Starting smartd: [ OK ] c CentOS release 5.4 (Final) Kernel 2.6.16-xenU on an i686 domU-12-31-39-00-C4-97 login: INIT: Id "2" respawning too fast: disabled for 5 minutes INIT: Id "3" respawning too fast: disabled for 5 minutes INIT: Id "4" respawning too fast: disabled for 5 minutes INIT: Id "5" respawning too fast: disabled for 5 minutes INIT: Id "6" respawning too fast: disabled for 5 minutes

  Read the article

• question about that concept of linux install in flash card.

  - by Johnny

  1.i can't understand why Linux on flash card need install, does it simply copy certain file to certain location in flash card? ---i mean ,plan it in a response file,then one program read the plan in response file and write certain format to flash card. 2.does the file system bind tightly to the linux kernel? is it possible let each kernel,user,app have its own root? rather than mount everything under one single / "root"

  Read the article

• Single machine & KVM-only Eucalyptus installation ?

  - by brainstorm

  Hi, I was wondering if there's an easy way to install Eucalyptus on a single VT-enabled machine (all Front End, CC, NC..), without installing XEN along with it's specific kernel and dependencies: kernel-xen x86_64 2.6.18-194.3.1.el5 update 20 M xen x86_64 3.0.3-105.el5_5.3 update 1.9 M xen-libs x86_64 3.0.3-105.el5_5.3 update 155 k Only KVM. Is it possible ? Do I have to go for sources instead of packages ?

  Read the article

• How to get more information from the system crash

  - by viraptor

  I'd like to debug an issue I'm having with a linux (debian stable) server, but I'm running out of ideas of how to confirm any diagnosis. Some background: The servers are running DL160 class with hardware raid between two disks. They're running a lot of services, mostly utilising network interface and CPU. There are 8 cpus and 7 "main" most cpu-hungry processes are bound to one core each via cpu affinity. Other random background scripts are not forced anywhere. The filesystem is writing ~1.5k blocks/s the whole time (goes up above 2k/s in peak times). Normal CPU usage for those servers is ~60% on 7 cores and some minimal usage on the last (whatever's running on shells usually). What actually happens is that the "main" services start using 100% CPU at some point, mainly stuck in kernel time. After a couple of seconds, LA goes over 400 and we lose any way to connect to the box (KVM is on it's way, but not there yet). Sometimes we see a kernel reporting hung task (but not always): [118951.272884] INFO: task zsh:15911 blocked for more than 120 seconds. [118951.272955] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [118951.273037] zsh D 0000000000000000 0 15911 1 [118951.273093] ffff8101898c3c48 0000000000000046 0000000000000000 ffffffffa0155e0a [118951.273183] ffff8101a753a080 ffff81021f1c5570 ffff8101a753a308 000000051f0fd740 [118951.273274] 0000000000000246 0000000000000000 00000000ffffffbd 0000000000000001 [118951.273335] Call Trace: [118951.273424] [<ffffffffa0155e0a>] :ext3:__ext3_journal_dirty_metadata+0x1e/0x46 [118951.273510] [<ffffffff804294f6>] schedule_timeout+0x1e/0xad [118951.273563] [<ffffffff8027577c>] __pagevec_free+0x21/0x2e [118951.273613] [<ffffffff80428b0b>] wait_for_common+0xcf/0x13a [118951.273692] [<ffffffff8022c168>] default_wake_function+0x0/0xe .... This would point at raid / disk failure, however sometimes the tasks are hung on kernel's gettsc which would indicate some general weird hardware behaviour. It's also running mysql (almost read-only, 99% cache hit), which seems to spawn a lot more threads during the system problems. During the day it does ~200kq/s (selects) and ~10q/s (writes). The host is never running out of memory or swapping, no oom reports are spotted. We've got many boxes with similar/same hardware and they all seem to behave that way, but I'm not sure which part fails, so it's probably not a good idea to just grab something more powerful and hope the problem goes away. Applications themselves don't really report anything wrong when they're running. I can run anything safely on the same hardware in an isolated environment. What can I do to narrow down the problem? Where else should I look for explanation?

  Read the article

• Server currently under DDOS, not sure what to do.

  - by Volex

  Hi, My web server is currently under a DDOS attack I believe, the messages log is full of these kind of messages: May 13 15:51:19 kernel: nf_conntrack: table full, dropping packet. May 13 15:51:19 last message repeated 9 times May 13 15:51:24 kernel: __ratelimit: 78 callbacks suppressed May 13 15:51:24 kernel: nf_conntrack: table full, dropping packet. May 13 15:52:06 kernel: possible SYN flooding on port 80. Sending cookies. and a netstat has a huge amount of the following: tcp 0 0 my.host.com:http bb176da0.virtua.com.br:4998 SYN_RECV tcp 0 0 my.host.com:http 187.0.43.109:2694 SYN_RECV tcp 0 0 my.host.com:http 109.229.4.145:1722 SYN_RECV tcp 0 0 my.host.com:http 189-84-163-244.sodobr:63267 SYN_RECV tcp 0 0 my.host.com:http bd66839d.virtua.com.br:3469 SYN_RECV tcp 0 0 my.host.com:http 69.101.56.190.dsl.int:52552 SYN_RECV tcp 0 0 my.host.com:http pc-62-230-47-190.cm.vt:2262 SYN_RECV tcp 0 0 my.host.com:http 189-84-163-244.sodobr:63418 SYN_RECV tcp 0 0 my.host.com:http pc-62-230-47-190.cm.vt:1741 SYN_RECV tcp 0 0 my.host.com:http zaq3d739320.zaq.ne.jp:2141 SYN_RECV tcp 0 0 my.host.com:http netacc-gpn-4-80-73.po:52676 SYN_RECV tcpdump shows: 7:11:08.564510 IP 187-4-1xx-4.xxx.ipd.brasiltelecom.net.br.54821 my.host.com.http: S 999692166:999692166(0) win 65535 17:11:08.566347 IP 114-44-171-67.dynamic.hinet.net.1129 my.host.com.http: S 605369055:605369055(0) win 65535 17:11:08.570210 IP 200-101-13-130.pvoce300.ipd.brasiltelecom.net.br.5590 my.host.com.http: S 2813379182:2813379182(0) win 16384 17:11:08.571290 IP dsl-189-143-30-99-dyn.prod-infinitum.com.mx.1615 my.host.com.http: S 281542700:281542700(0) win 65535 17:11:08.583847 IP dsl-189-143-30-99-dyn.prod-infinitum.com.mx.1617 my.host.com.http: S 499413892:499413892(0) win 65535 17:11:08.588680 IP 170.51.229.112.2569 my.host.com.http: S 2195084898:2195084898(0) win 65535 17:11:08.588773 IP gw2-1.211.ru.3180 my.host.com.http: F 2315901786:2315901786(0) ack 2620913033 win 64240 17:11:08.590656 IP 200-101-13-130.pvoce300.ipd.brasiltelecom.net.br.5614 my.host.com.http: S 2813715032:2813715032(0) win 16384 17:11:08.591212 IP 203.82.82.54.15848 my.host.com.http: S 4070423507:4070423507(0) win 16384 17:11:08.591254 IP 203.82.82.54.2545 my.host.com.http: S 1790910784:1790910784(0) win 16384 17:11:08.591289 IP 203.82.82.54.28306 my.host.com.http: S 578615626:578615626(0) win 16384 17:11:08.591591 IP gw2-1.211.ru.3191 my.host.com.http: F 2316435991:2316435991(0) ack 2634205972 win 64240 17:11:08.591790 IP 200-101-13-130.pvoce300.ipd.brasiltelecom.net.br.5593 my.host.com.http: S 2813659017:2813659017(0) win 16384 17:11:08.593691 IP gw2-1.211.ru.3203 my.host.com.http: F 2316834420:2316834420(0) ack 2629074987 win 64240 I'm not sure what I can do to limit/mitigate this, currently no webpages are being served, any help gratefully appreciated.

  Read the article

• Why version of my Darwin is 10.3, while I have Mac OS 10.6?

  - by Vincenzo

  This is what I see on my Mac: $ uname -a Darwin be-2.local 10.3.0 Darwin Kernel Version 10.3.0: Fri Feb 26 11:58:09 PST 2010; root:xnu-1504.3.12~1/RELEASE_I386 i386 I have Mac OS X 10.6.3. Why the kernel is of version 10.3? And how can I upgrade it? Thanks.

  Read the article

• Routing RFC1918 addresses through dd-wrt via a switch

  - by espenfjo

  I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

  Read the article

• Are memory leaks really something to worry about?

  - by chuck final

  I came across this post today, arguably debatable/wrong somewhat, but worth a shot looking over: http://andyharglesiscodebase.wordpress.com/2013/11/01/why-programmers-shouldnt-worry-about-memory-leaks/ The poster claims that modern OSes automatically have garbage collection implemented in the kernel memory, and that any unfreed user heap memory is managed during "post partum cleanup". It seems like rubbish, but I can't be 100% sure since I am not that knowledgeable on the kernel's memory management setup, etc.

  Read the article

• Extracting init script from bult-in intrfs into Linux bzImage

  - by Maciej Piechotka

  I have following problem - I damaged my system (Gentoo - by rebuilding using gcc 4.5) beyond repair. I unmounted /home, copied /etc + other important files and I've started reinstalling system. However I forgot to copy init script. It is still present in kernel image that I have. How to extract it? Please note that initrd is not a separate file but is in the kernel image.

  Read the article

• Grub Solaris FreeBSD dual boot

  - by pallavt

  I have solaris 10 installed on the first hard disk and freebsd installed on the second hard disk I edited the /boot/grub/menu.lst from solaris to the following title FreeBSD root (hd1,0) kernel /boot/loader Now when I try to boot into freebsd via the grub, it gives the following error root (hd1,0) Filesystem type unknown, partition type 0xee kernel /boot/loader Error 17: cannot mount selected partition

  Read the article

• Why is Windows 7 announcing itself as an IPv6 router?

  - by Paul

  I have a 6in4 ipv6 connection from a linux box to a broker. I use gogoc to establish the connection to the broker, and radvd to advertise the route to clients on the network. All this appears to work, the problem is that I have a Windows 7 machine on the same network, and it is advertising itself as a ipv6 router. Which it is not. This is output from radvdump: # # radvd configuration generated by radvdump 1.8.5 # based on Router Advertisement from [snip]:ea2 # received by interface eth0 # interface eth0 { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag on; AdvOtherConfigFlag on; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 0; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvSourceLLAddress on; AdvLinkMTU 1500; }; # End of interface definition # # radvd configuration generated by radvdump 1.8.5 # based on Router Advertisement from [snip]:1121 # received by interface eth0 # interface eth0 { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag off; AdvOtherConfigFlag off; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 64; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvLinkMTU 1280; AdvSourceLLAddress on; prefix [snip]::/64 { AdvValidLifetime 86400; AdvPreferredLifetime 14400; AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; # End of prefix definition }; # End of interface definition And I end up with two routes: $ ip -6 route [snip]::/64 dev eth0 proto kernel metric 256 expires 86117sec fe80::/64 dev eth0 proto kernel metric 256 default via [snip]:ea2 dev eth0 proto kernel metric 1024 expires 1492sec default via [snip]:1121 dev eth0 proto kernel metric 1024 expires 1506sec The ea2 route is to the Windows7 box. It doesn't have a router installed, and doesn't have any tun/tap interfaces. I can't see why it is doing this. I could disable ipv6 on it, but I want it to be a client, not a router. Update: The IP Helper service (Provides tunnel connectivity using IPv6 transition technologies (6to4, ISATAP, Port Proxy, and Teredo), and IP-HTTPS. If this service is stopped, the computer will not have the enhanced connectivity benefits that these technologies offer.) seems to be the culprit, as if it is stopped, I don't get the routes advertised. So my question is now more specifically "why is IP Helper announcing routes?".

  Read the article

• Wirelss card not being detected in backtrack 5

  - by Jesse Nelson

  I just installed backtrack 5 and I am unable to detect my wireless card. iwconfig doesn't list my interface. I can see that the hardware is present in lspci -vnn (see below) but I can't get the interface detected. I have tried to reinstall the compat-wireless package but I get errors during the build (see below) I have done a ton of researching and I keep hitting a brick wall, mostly because the wiki for backtrack is down and I can't find any good resources. Does anyone know how to fix the issue? Also, does anyone no how I can scan the hardware to determine what NIC is assigning my interface? If I can figure out the interface name I think I can set it up manually by putting up the link and using wireless-tools to manually configure the connection, this is what I had to do in arch on my mac. As stated the wiki for backtrack is down and I can't find any help on the issue. I tried to do the full kernel upgrade suggested in my software update but after the update was complete and I logged back in I had a new log in manager and the only thing I was able to log into was window managers. However, after this update my wireless was working fine. Please help I am new to Linux and the wiki is down, I have nowhere else to turn. Forgot to mention I am using the KDE version, not Gnome. Thanks in advance for any help or support. Attempt at make: root@bt:/usr/src/compat-wireless-3.3-rc1-2# make /usr/src/compat-wireless-3.3-rc1-2/config.mk:254: "WARNING: CONFIG_CFG80211_WEXT will be deactivated or not working because kernel was compiled with CONFIG_WIRELESS_EXT=n. Tools using wext interface like iwconfig will not work. To activate it build your kernel e.g. with CONFIG_LIBIPW=m." make -C /lib/modules/2.6.38/build M=/usr/src/compat-wireless-3.3-rc1-2 modules make: *** /lib/modules/2.6.38/build: No such file or directory. Stop. make: *** [modules] Error 2 lspci output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn -i net lspci: I/O error at net, line 0 root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn 02:00.0 Network controller [0280]: Atheros Communications Inc. Device [168c:0032] (rev ff) (prog-if ff) !!! Unknown header type 7f ( This is the problem but I can't find the solution) Kernel modules: ath9k iwconfig output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• How can I modify the Ubuntu Server install CD to add a hardware driver?

  - by Matt

  I found this link to modify an Ubuntu install CD. https://help.ubuntu.com/community/InstallCDCustomization However, I want to put the Adaptec aic94xx RAID driver onto the disk so that my RAID controller is recognised and I can set up a mirror. How do I go about doing this? Firmware file is: http://kernel.org/pub/linux/kernel/people/jejb/aic94xx-seq.fw

  Read the article

• solaris 10 - custom jumpstart menu.lst

  - by romant

  Is it possible to include the config.tar (encompasses the rules before/after scripts…) instead of on a web server served through http:// - but included no the cdrom itself. Namely am trying to do something along the lines of: title Solaris kernel$ /boot/multiboot kernel/$ISADIR/unix install cdrom:/config/config.tar dhcp -B install_media=cdrom module$ /boot/$ISADIR/x86.miniroot Yet it seems Solaris only supports HTTP or NFS as the source for config.tar - and not the CDROM itself. Any ideas? Thank you.

  Read the article

• A gigabit network interface is CPU-limited to 25MB/s. How can I maximize the throughput?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? As a reference, the other computers in the network can usually transfer at 50+MB/s without problems. A computer with a Core 2 CPU generates only 5000 interrupts per second when it's transferring at 110MB/s. The number of interrupts is about 20 times less than the Atom system (if interrupts scale linearly with throughput.) And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• MTD mtd3ro backup returns BCH decoding failed

  - by saeed144

  While doing a kernel backup of an mtd (Memory Technology Device) from /dev/mtd/mtd3ro of a TI board gives many "BCH decoding failed", Here are system info #cat /proc/mtd dev: size erasesize name mtd0: 00080000 00020000 "X-Loader" mtd1: 00140000 00020000 "U-Boot" mtd2: 000c0000 00020000 "U-Boot Env" mtd3: 00500000 00020000 "Kernel" mtd4: 1f880000 00020000 "File System" here is the method used, dd if=/dev/mtd/mtd3ro of=/data/local/tmp/mtd3.bin doing a cat also returns the same error, and here is the error, BCH decoding failed BCH decoding failed yes, the destination has enough space ;) tell me what do you think? Thanks

  Read the article

• Limit NFS block size from server side?

  - by paulw1128

  Is it possible to enforce a maximum rsize/wsize in nfsd? I'm having issues related to IP fragmentation (yes, I'm stuck with NFS-over-UDP, contrary to the warnings in the manpage), and have no practical access to the client mount command (buried in one of many TFTP boot images). http://nfs.sourceforge.net/nfs-howto/ar01s05.html lists a kernel source parameter limiting the maximum block size, but I'm not gong to get away with recompiling the nfsd kernel module so that's not really an option either :-(

  Read the article

• How to turn off ASLR in Ubuntu 9.10

  - by Summer_More_More_Tea

  Hi everyone: I want to turn off ASLR on my own PC. But each time I type "sudo echo 0 /proc/sys/kernel/randomize_va_space", the system shows that "Permission denied". How can I make it work? By the way, my OS kernel is 2.6.30. Hope anyone can give me a hand. Regards.

  Read the article

• Bridging and iptables SNAT conflict

  - by sad_admin

  Hello I am working on a setup here and have it working with one minor exception. Devices on one side of my bridge aren't getting SNAT'd to the Internet. The Diagram / Overview: Primary_Network (Site_A) | | Internet ------- Linux_Bridge_GW (GW) | | Secondary/CoLo Site (Site_B) Here is the setup: 1.) Site_A has all the production servers and workstations. 2.) Site_B has a set of servers that we would like to fail-over to and also serve our internet facing services from. 3.) GW has two interfaces that are trunked and carrying the appropriate VLAN traffic (allow layer-2 propagation of traffic between sites) //this all works perfectly fine. 4.) The problem that is being encountered is, hosts from Site_B have their default GW at Site_A (same subnet) GW does not have IPs on the VLANs that are being passed. 5.) All hosts at Site_A can reach the Internet without problem. 6.) GW has an addresses on a subnet that is ONLY for Internet destined traffic. (This was done so that Websense would not have to parse unnecessary traffic. We use this VLAN as the monitor port's source on the switch where Websense is sitting). What I think is happening: 1.) Packet/Frame comes in on physdev at Site_B destined for Internet. 2.) Kernel sees packet, and forwards it out the other side of the bridge to that host's default GW. 3.) Site_A (containing core-network's Default-GW) sees that packet is destined for a host it doesn't know about, so it sends it to it's default GW (the linux bridge, since it's Internet bound). 4.) The kernel says "Hey, I've seen you before" and therefore doesn't do SNAT'ing on the packet and sends it out to the Internet where it's black-holed. Why I think it's happening: 1.) A tcpdump on the internet facing NIC shows the packet leaving the interface with the private address as it's source. What I would like: 1.) Have the packet SNAT'd. 2.) Something like the below would be awesome a.) packet comes in from Site_B b.) kernel sees that the packet is NOT destined for itself or any private address c.) kernel says "OK, well since you're destined for the Internet I'm going to send you out this interface rather than forward you to your normal default GW that's WAAAY over there." d.) packet comes in from internet and is sent out the appropriate bridge physdev depending on which site the host it's destined for is at. Thanks for any assistance or guidance that you are willing to offer. Best Regards, Sad Admin

  Read the article

• Problem with two kernels installed and '@fedora' entries in 'yum list'?

  - by Paul

  FC11 beta upgraded to FC12. When I do yum list I see listing on the far right column as follows: 'fedora' 'installed' and '@fedora'. Previously I never had '@fedora' and only seemed to appear when I upgraded from FC11-FC12. Also when i look at the kernels installed I have kernel-PAE 2.6.30-0.97.rc.fc12 installed kernel-PAE 2.6.31.5-127.fc12 @fedora Why do I have two entries?

  Read the article

• Is the XP VMM a bottleneck on a multi core machine?

  - by JeffV

  I have a dual Xeon hex core machine running an IO intensive application. (WinXP 32) I am seeing a hardware driver (1/2 user mode, 1/2 kernel, streaming data) that is using 6k delta page faults per second. When other applications load or allocate large amounts of memory the driver's hardware buffer gets an underrun (application not feeding it fast enough). Could this be because the kernel is only using one core to service page fault interrupts?

  Read the article

< Previous Page | 288 289 290 291 292 293 294 295 296 297 298 299  | Next Page >