Search Results

Search found 10695 results on 428 pages for 'some none'.

Page 296/428 | < Previous Page | 292 293 294 295 296 297 298 299 300 301 302 303  | Next Page >

• Sparc Solaris 2.6 will not boot

  - by joshxdr

  I have a very old Sparc Solaris network that was working fine last week, but after a power outage none of the workstations will boot. The network looks like this: host A: solaris 2.6, shares /export/home to network by NFS host B: solaris 8, runs NIS server. Mounts /export/home/ by NFS. host C: RHEL5, shares /share to network by NFS. Mounts /export/home/ by NFS. I figured that the main problem was host A, since you need the home directories available for the other workstations to boot(?). Host A does not mount anything by NFS as far as I know. However, this workstation will NOT boot. The OBP bootup sequence looks like this: Boot device <blah> configuring network interface le0 Hostname <hostname> check file system <everything ok> check ufs filesystem <everything ok> NIS domainname is <name> starting router discovery starting rpc services: rpcbind keyserv ypbind done setting default interface for multicast: add net 224.0.0.0: gateway <hostname> <HANGS at this point> Is there some kind of debug mode so that I can get more detail as to why the workstation won't boot? Is my network structure inherently susceptible to power outage? Is there a way I can boot up to command line so I can at least turn off the NFS mounting?

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• Why is this setting for Name-based Virtual Host settings not working?

  - by Kave

  I have two domains (siteA.com & SiteB.com) that point to the same webserver and I would like to show different web pages for each. The steps I have taken so far are: Copy the default site (siteA) to siteB 1) sudo cp /etc/apache2/sites-available/default /etc/apache2/sites-available/siteB 2) sudo vim /etc/apache2/sites-available/siteB <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/siteB <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/siteB> Options Indexes FollowSymLinks MultiViews AllowOverride FileInfo Indexes Order allow,deny allow from all </Directory> </VirtualHost *:80> Then I created under /var/www/siteB and created a sample index.html in there. However when I load my domain siteB.com I still get directed to /var/www/siteA. Why is that? Do I have to rename the /etc/apache2/sites-available/default to /etc/apache2/sites-available/siteA as well? UPDATE: Thanks to the answer below it seems I had forgotten next to enabling the site also another entry: <VirtualHost *:80> ServerAdmin [email protected] ServerName siteB.com ServerAlias www.siteB.com </VirtualHost *:80> in order to include all subdomains as well then do: <VirtualHost *:80> ServerAdmin [email protected] ServerName siteB.com ServerAlias *.siteB.com </VirtualHost *:80> Same goes for siteA.

  Read the article

• Firefox takes a really long time to load some sites on Ubuntu

  - by Dave

  Hello guys, I have an issue here. Some sites - just a few - takes a really long time to load on Firefox. One example is A List Apart (http://www.alistapart.com/) which takes more than 30 minutes (yes, minutes, not seconds). On Opera, ou even through a telnet session, the problematic sites run without problem, fast as expected. I am using Linux 8.04, running Firefox 3.6.3 downloaded from mozilla site, with a 10M ADSL connection. I tried many tweaks I found googling, like disable IPv6, and change http pipelining settings on FF's about:config. None worked. I also used Firebug to find what phase during negotiation is the bottleneck. Findings are in the screenshot. Well guys, any idea what is the issue? And how to solve it? I repeat, this only happens with firefox (3.6.3 and prior versions), for a few sites only (even sites with much more requests, images, javascripts, stylesheets work fine), and http pipelines and IPv6 tweaks on about:config didn't work. Thanks

  Read the article

• Lenovo System Update Breaks Windows Live

  - by wolfvilleian

  Hey everyone, I've been racking my brain (and fingers from typing) trying to solve this issue to no avail. I have a Lenovo computer and I install their system update tool to install all my missing drivers. However after this tool is installed Windows Live 2011 breaks, it will no longer sign in giving error number 8e5e0247 all the solutions online haven't helped. It appears that a language setting somewhere gets set to en_ms, and I'm en_ca. My computer is running Windows 7 x64. When i try to sign onto messenger it gives an error that (with some research) means your locale or language is not supported, I've searched my computer for any reference to en_ms but find none. Also a few other things seem to have broken, When a UAC box comes up it is no longer able to identify the publisher of anything, and also the indexing service does not work (I'm not sure if the indexing issue is related, but the UAC issue happened right after installation), I had this issue before but I don't remember how I fixed it, I believe it had something to do with environmental variables. When it goes to sign in it gets as far as the "Loading contacts" then stops and goes back to the sign in screen. Has anyone seen this before? Thanks

  Read the article

• Unable to mount root fs over NFS [on hold]

  - by johnmadrak

  I am attempting to set up a Raspberry Pi running Pidora to boot from an NFS share. My configuration in cmdline.txt is: dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/nfs nfsroot=<serverip>:/fake/path,nfsvers=3,rw,nolock nfsrootdebug ip=dhcp elevator=deadline rootwait On the Pi, the output I see is: IP-Config: Got DHCP answer from <router>, my address is <clientip> IP-Config: Complete: device=eth0, hwaddr=<macaddress>, ipaddr=<clientip>, mask=255.255.255.0, gw=<routerip> host=<clientip>, domain=, nis-domain=(none) bootserver=<routerip>, rootserver=<serverip>, rootpath= nameserver0=<routerip> (It pauses for a bit here) VFS: Unable to mount root fs via NFS, trying floppy VFS: Cannot open root device "nfs" or unknown-block(2,0); error -6 Please append a correct "root=" boot option; here are the available partitions: ..... On the NFS Server (an OpenVZ Container), the output I see in the /var/log/messages is: Aug 22 23:24:01 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:783 for /fake/path (/fake/path) Aug 22 23:24:38 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:741 for /fake/path (/fake/path) Aug 22 23:25:25 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:752 for /fake/path (/fake/path) Aug 22 23:26:12 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:876 for /fake/path (/fake/path) To test, I've made sure I can mount (non-root) from both the Pi and another machine and it worked. Does anyone have an idea on what could be wrong or how to narrow it down? Thank you in advanced for your help.

  Read the article

• Can't get DNS Alias work on Ubuntu 10.04 with Apache 2

  - by Johnny

  I want to use the DNS Alias to configure one of my domain pointing to a specific directory on the server. Here is what I've done: Change the IP address in domain setting, and it works $ ping www.example.com PING example.com (124.205.62.xxx): 56 data bytes 64 bytes from 124.205.62.xxx: icmp_seq=0 ttl=48 time=53.088 ms 64 bytes from 124.205.62.xxx: icmp_seq=1 ttl=48 time=52.125 ms ^C --- example.com ping statistics --- 2 packets transmitted, 2 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 52.125/52.606/53.088/0.482 ms Add sites-available and sites-enabled $ ls -l /etc/apache2/sites-available/ total 16 -rw-r--r-- 1 root root 948 2010-04-14 03:27 default -rw-r--r-- 1 root root 7467 2010-04-14 03:27 default-ssl -rw-r--r-- 1 root root 365 2010-06-09 18:27 example.com $ ls -l /etc/apache2/sites-enabled/ total 0 lrwxrwxrwx 1 root root 26 2010-06-09 15:46 000-default -> ../sites-available/default lrwxrwxrwx 1 root root 33 2010-06-09 18:17 001-example.com -> ../sites-available/example.com But it doesn't work and when I open the browser for www.example.com, it shows an 111 error: The following error was encountered: Connection to 124.205.62.48 Failed The system returned: (111) Connection refused Here is how example.com's config: $ cat /etc/apache2/sites-enabled/001-example.com <virtualhost *:80> DocumentRoot "/vhosts/example.com/htdocs/" ServerName www.example.com ServerAlias example.com <Location /> Order Deny,Allow Deny from None Allow from all </Location> #Include /etc/phpmyadmin/apache.conf ErrorLog /vhosts/example.com/logs/error.log CustomLog /vhosts/example.com/logs/access.log combined Could you please tell me how to solve this?

  Read the article

• Suddenly getting lock timeouts with MySQL

  - by Marc Hughes

  We've got a web app hosted on Amazon Web services. Our database is a multi-az RDS MySQL server running 5.1.57 and 3-4 app servers talk to it. Today, we started seeing a lot of errors along the lines of "Lock wait timeout exceeded; try restarting transaction" - almost 1% of POST requests are seeing this. There have been no modifications to the code running on the site. There have been no schema changes. We haven't had a big spike in traffic. I've been looking at the processes running, and none seem out of control. I tried scaling our RDS instance from a small to a large, with no effect. Two days ago, Amazon had some outages. As part of the recovery from that, our RDS server, and our app servers ended up in different availability zones, but all within the same region. But yesterday, everything was fine so I'm not convinced that's related. The lock timeouts are in different types of requests and occur in different InnoDB tables. I have noticed the number of open connections jumped when we started seeing problems, but they may be a symptom and not a cause. What are my next steps in debugging this?

  Read the article

• How to debug modsecurity_audit_log

  - by max87

  I was accessing www.example.com/RestAPI/index.php/tweets.json in my server. The modsec_audit.log showed the following error, but there is no related errors/warnings in modsec_debug.log. I could see the Internal Server error is logged in example-error_log. How can I debug this Internal Server error? --8560e90b-A-- [21/Mar/2012:07:01:52 +0000] T2l84H8AAAEAAGxPZ@QAAAAG x.x.x.x 33101 x.x.x.x 80 --8560e90b-B-- GET /RestAPI/index.php/tweets.json HTTP/1.1 Host: www.example.com User-Agent: Mozilla/5.0 (X11; Linux i686; rv:11.0) Gecko/20100101 Firefox/11.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,/;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip, deflate DNT: 1 Cookie: __utma=159129855.1463065063.1331789485.1331789485.1331789485.1; __utmz=159129855.1331789485.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); 8cb6a414cf5ec1919864de0e80bea4da=0es7dcu0p10cocfpferb2lddi0; 8926e4f3c475bb6fcacb409299f1bd27=53cf8c5e6bf78ea45096945377e6d609 Connection: keep-alive Cache-Control: max-age=0 --8560e90b-F-- HTTP/1.0 500 Internal Server Error X-Powered-By: PHP/5.3.5 Content-Length: 0 Connection: close Content-Type: text/html; charset=UTF-8 --8560e90b-H-- Apache-Handler: php5-script Stopwatch: 1332313312358005 130428 (- - -) Producer: ModSecurity for Apache/2.5.12 (http://www.modsecurity.org/); core ruleset/2.0.5. Server: Apache --8560e90b-Z--

  Read the article

• Xen Bridge only working when IP Assigned

  - by m.sr

  Hey! Just had an (in my sense) obscure situation. I have a Xen Server with bridged networking. Everything works fine since month. A while ago i configuresd a second bridge. only some DomUs get an channel on this bridge - my Dom0 doesn't need to / should'nt use this bridge. So just 5 minutes ago while rebooting the xen host (because of an other problem with the UPS) i decided to removed the fixed ip from the the interface of the Dom0 which belongs to the second bridge. So after reboot i noticed that none of the interfaces on the second bridge is available. I couldn't find a problem. Everything was just like before the reboot, except the interface of the Dom0 had no IP address. After a while i tried to give the DomO interface of this bridge an IP again and ... BOOM ... everything is up and running again! WTF? Why is it important to have the interface of a bridge configured in the Dom0? Even when confiugured 'wrong' (complitely different netowkr settings as the network really hanging on the bridge) everythjing works fine ... I don't get it. Could please someone explain? Tnaks a lot!

  Read the article

• Exchange 2010 Transport rules stepping on each other

  - by TopHat

  I have a group of users that I have to restrict email access for and so far using Exchange Transport Rules has worked very well. The problem I am having is that Rule 0 is supposed to bcc the email to a review mailbox but otherwise not change anything and Rule 9 is supposed to block the email and throw a custom NDR to tell the user why they were blocked. Here are my results in practice however. If Rule 0 is enabled and Rule 9 is enabled then only Rule 9 functions If Rule 0 is disabled and Rule 9 is enabled then Rule 9 functions If Rule 0 is enabled and Rule 9 is disabled then Rule 0 functions This is after the Transport Service has been restarted (multiple times actually). I have other rule pairs that work correctly. None of these are overlapping rulesets however. - copy email going to address outside domain and then block - copy email coming in from outside and then block Here is the rule for copying internal emails (Rule 0): Apply rule to messages from a member of Blind carbon copy (Bcc) the message to except when the message is sent to a member of or [email protected] Here is the rule to block the same email (rule 9): Apply rule to messages from a member of send 'Email to non-supervisors or managers has been prohibited. Please contact your supervisor for more information.' to sender with 5.7.420 except when the message is sent to , [email protected], The distribution group used for membership in these rules is used for the other blocking and copying rules and works as expected. Is there something I missed in this setup? All of the copy rules are at the front of the transport rule group and all the actual copies at at the end of the queue if that makes a difference. Any thoughts as to why the email doesn't get copied when it gets blocked?

  Read the article

• How to configure a large mtu (linux)

  - by Somejan

  I have a gigabit ethernet connection from my laptop to my router, and a working ipv6 connection to the internet. I can receive very large packets from sites on the internet, with sizes up to at least 10000 bytes (according to wireshark). (edit: turns out to be linux's 'generic receive offload') However, when trying to send anything, my local computer fragments at just below 1500 bytes for ipv6. (On ipv4, I can send tcp packets to the internet of at least 1514 bytes, I can ping with packets up to the configured mtu of 6128 but they are blackholed.) I'm on ubuntu 12.04. I have configured an mtu for my eth0 of 6128 (the maximum it accepts), both using ip link set dev eth0 mtu 6128 and in the NetworkManager applet gui, and restarted the connection. ip link show eth0 shows the 6128 mtu is indeed set. ip -6 route shows that none of the paths the kernel knows about have an mtu set. I can ping over ipv4 with packets up to 6128 bytes (though I don't get responses), but when I do ping6 myrouter -c3 -s1500 -Mdo I get error replies from my own computer saying that the packets are too large and the mtu is 1480. I have confirmed with Wireshark that nothing is put on the wire, and the replies are indeed generated by my own computer. So, how do I get my computer to use the larger mtu?

  Read the article

• How to play 24 fps video smoothly on a 60Hz display? (or which player supports frame interpolation?)

  - by netvope

  I use mpc-hc to play videos on Win7 x64. With the default settings (#1), video playback is great most of the time. But for panning shots, playback is not smooth. I stepped through the video frame by frame and found that the panning movement is smooth (e.g. each frame shifts horizontally by 10 pixels), so the problem is how the 23.976 fps video is interpolated to 60Hz. The judder looks like what would be caused by a "2:3 pulldown", where the frames are played unevenly like: frame 1, 1, 2, 2, 2, 3, 3, 4, 4, 4, etc (#2) Using "optimal renderer settings" (#3) instead of the default disables the Aero theme and causes tearing. Setting my LCD display to 50Hz may have improved the judder slightly (but I can't really tell). My display does not support 24Hz or 48Hz, and forcing them in the Nvidia control panel gives blurry screen. I've tried other video players (VLC and KMPlayer), the ReClock Directshow Filter, video files from different sources (#4), turning on/off DXVA, and a computer with a different GPU, but the judder in the playback is similar. None of them solved the problem. So, how can I play 23.976 or 24 fps video smoothly on a 60Hz display? I think a video player could make the video smoother by doing linear interpolation, such as: 1. 100% frame 1 2. 60% frame 1 + 40% frame 2 3. 20% frame 1 + 80% frame 2 4. 80% frame 2 + 20% frame 3 5. 40% frame 2 + 60% frame 3 6. 100% frame 3 7. 60% frame 3 + 40% frame 4 .. etc Can any existing video player do this? Footnotes: (#1) Video renderer: EVR Custom Pres. (#2) This example converts a 24 fps video into 30 fps (#3) View Renderer settings Reset Reset to optimal renderer settings (#4) The files I have are all H.264 mkv files, but I don't think the file format/encoding matters.

  Read the article

• LDAP Account Locked Out Sporadically after Password change - Finding the source of invalid attempts

  - by CityView

  On a small network of machines (<1000) we have a user whose account is being locked out after an indeterminate interval following a password change. We are having severe difficulties finding the source of the invalid logon attempts and I would appreciate it greatly if some of you could go through your thought process and the checks you would perform in order to fix the problem. All I know for sure is that the account is locked out several (5+) times a day, I can't even be sure it's due to failed login attempts as there is no record of failure until the account is locked. So far I have tried; Logging the account out of everything we can think of and back in with the new password Scanning the user's box for any non standard software which might perform an LDAP lookup Checking all installed services on our production boxes to check none are attempting to run under the account Changing the user back to their old password (Problem persists so perhaps password change is a red herring) Wireshark on a box where lots of LDAP authentication is performed - Rejects only occur after account is already locked out Clearing the credential cache in - Control Panel - User Accounts - Advanced Looking at the local I'm at a loss for what to try. I am happy to try any suggestions you have in order to diagnose the issue. I think my question boils down to a simple request; I need a technique for deriving the source (Application/Host) of the invalid login attempts which are causing the account to be locked. I'm not sure if that's even possible but I suspect there must be more I can try. Many thanks, CityView

  Read the article

• How to force mdadm to stop RAID5 array?

  - by lucek

  I have /dev/md127 RAID5 array that consisted of four drives. I managed to hot remove them from the array and currently /dev/md127 does not have any drives: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdd1[0] sda1[1] 304052032 blocks super 1.2 [2/2] [UU] md1 : active raid0 sda5[1] sdd5[0] 16770048 blocks super 1.2 512k chunks md127 : active raid5 super 1.2 level 5, 512k chunk, algorithm 2 [4/0] [____] unused devices: <none> and mdadm --detail /dev/md127 /dev/md127: Version : 1.2 Creation Time : Thu Sep 6 10:39:57 2012 Raid Level : raid5 Array Size : 8790402048 (8383.18 GiB 9001.37 GB) Used Dev Size : 2930134016 (2794.39 GiB 3000.46 GB) Raid Devices : 4 Total Devices : 0 Persistence : Superblock is persistent Update Time : Fri Sep 7 17:19:47 2012 State : clean, FAILED Active Devices : 0 Working Devices : 0 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 512K Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 0 0 2 removed 3 0 0 3 removed I've tried to do mdadm --stop /dev/md127 but: mdadm --stop /dev/md127 mdadm: Cannot get exclusive access to /dev/md127:Perhaps a running process, mounted filesystem or active volume group? I made sure that it's unmounted, umount -l /dev/md127 and confirmed that it indeed is unmounted: umount /dev/md127 umount: /dev/md127: not mounted I've tried to zero superblock of each drive and I get (for each drive): mdadm --zero-superblock /dev/sde1 mdadm: Unrecognised md component device - /dev/sde1 Here's output of lsof|grep md127: lsof|grep md127 md127_rai 276 root cwd DIR 9,0 4096 2 / md127_rai 276 root rtd DIR 9,0 4096 2 / md127_rai 276 root txt unknown /proc/276/exe What else can I do? LVM is not even installed so it can't be a factor.

  Read the article

• Problem with Strange VMWare behaviour when shutting down guest.

  - by adza77

  Hi, I've been having a problem for a while now with VMWare Workstaion. (Originally with 6.5, but now with 7.0 and 7.0.1 too). The problem occurs when I choose to shut down a guest. VMWare itself seems to hang. If I choose to shut down a guest that's opened full screen, and during the process I minimise the screen to work on other applications in the host, often (not all the time) when I return to the guest I have a 'greyed out' screen and the system becomes unresponsive. The host O/S still seems to be working, but I am unable to switch to other applications. (I can bring up the taskbar on the host and 'see' other applications and even switch to them, but VMWare still stays 'on top' being unresponsive). I can not terminate VMWare even when windows says that the application has become unresponsive and gives me the option to terminate. VMWare stays on top, and I'm forced to either shutdown, or log off and log back on in order to regain control of my computer. This happens with both Windows 7 and Windows Vista guest operating systems (32 bit), and I have had it happen on multiple host machines, and multiple guest machines too. Current Host: Windows 7 64 bit, 8GB Ram, 500GB HDD, i7 Processor. I have been searching for more than 6 months for a solution but have found none, so finally decided to post here. Does anyone know what might be causing the problem (+or even how to minimize the VM so I can at least access any other applications and save work before forcing a logoff / reboot+) would be extrememly handly. If I know the correct keystrokes to save and close in an application on the host I can do this by task-switching to the desired app to save and close successfully, but I can't see what I'm doing because VMWare Workstation is still on-top 'greyed' out. Cheers Adam.

  Read the article

• Problem with Strange VMWare behaviour when shutting down guest.

  - by adza77

  Hi, I've been having a problem for a while now with VMWare Workstaion. (Originally with 6.5, but now with 7.0 and 7.0.1 too). The problem occurs when I choose to shut down a guest. VMWare itself seems to hang. If I choose to shut down a guest that's opened full screen, and during the process I minimise the screen to work on other applications in the host, often (not all the time) when I return to the guest I have a 'greyed out' screen and the system becomes unresponsive. The host O/S still seems to be working, but I am unable to switch to other applications. (I can bring up the taskbar on the host and 'see' other applications and even switch to them, but VMWare still stays 'on top' being unresponsive). I can not terminate VMWare even when windows says that the application has become unresponsive and gives me the option to terminate. VMWare stays on top, and I'm forced to either shutdown, or log off and log back on in order to regain control of my computer. This happens with both Windows 7 and Windows Vista guest operating systems (32 bit), and I have had it happen on multiple host machines, and multiple guest machines too. Current Host: Windows 7 64 bit, 8GB Ram, 500GB HDD, i7 Processor. I have been searching for more than 6 months for a solution but have found none, so finally decided to post here. Does anyone know what might be causing the problem (+or even how to minimize the VM so I can at least access any other applications and save work before forcing a logoff / reboot+) would be extrememly handly. If I know the correct keystrokes to save and close in an application on the host I can do this by task-switching to the desired app to save and close successfully, but I can't see what I'm doing because VMWare Workstation is still on-top 'greyed' out. Cheers Adam.

  Read the article

• Master File Table Corrupt, any way to save data?

  - by domen

  hi. I've used search, but none of the results match my problem so I didn't have to ask separate question. I've Installed Windows 7 RTM recently and since then partitions located on one of my HDDs have gone "crazy". They used to "freeze" and didn't open in explorer for some time (minute or two, usually), sometimes all partitions of the drive wouldn't show until reboot and finally, one of those partitions started showing "disk structure is corrupted and unreadable" warning, it appeared in Disk Management window as RAW and chkdsk showed "mft corrupt". There were no important data on the partition and I didn't have enough time to analyze the problem at the moment, so I just reformatted it and ran antivirus scan on system. After that problem settled for some time, but yesterday the problematic HDD vanished again from the system. After reboot chkdsk identified mft of four partitions corrupt and now they are all in same conditions as the above mentioned one. But the difference is that the files stored in them are extremely important. and just for info: I upgraded from Win7 build 7077, but had some performance issues, so I reformatted system drive and installed fresh Win7 RTM on it. I've downloaded TestDisk and it shows all the partitions marked as NTFS (not RAW) and my knowledge of the program wasn't sufficient to obtain any other info from it :-) and the images that could help describe the problem (sorry, I'm not allowed to post images and more than one hyperlink): http:// img22.imageshack.us/img22/5909/chkdskz.jpg http:// img198.imageshack.us/img198/5576/computeray.jpg I'm interested, is there a way to let me restore the MFT or just access files so I can backup them before reformatting the drive. Thanks for your time. :) P.S. my reformatted drive is showing no problems, could there be a problem with windows 7 itself? I googled, but with no results.

  Read the article

• How to correctly deploy Adobe Reader 9.1

  - by Ben Gillam

  Hi I have recently tried to deploy Adobe Reader 9.1 onto our network here. (SBS 2003 server and XP Workstations) I followed the instructions for the extraction of the installer and .msi and then creating a .mst transform file to set custom options. (Suppress EULA, dont create desktop icon etc) I then added the package to my deployment GPO applied the relevant .mst file and preceded to deploy accross the network. The software package is computer assigned to be installed prior to logon, to avoid user permissions issues. The package deploys correctly to computers and will run perfectly fine if you run from a shortcut, however when trying to view a pdf from within a web browser it fails with the following message. "The adobe acrobat/reader that is running can not be used to view PDF files in a web browser. Adobe Acrobat/Reader version 8 or 9 is required. Please exit and try again" I have found many pages on google refering to this problem, but none appear to be in relation the problems I have found. http :// kb2.adobe.com/cps/405/kb405461.html These fixes recommend correcting a registry entry (which i should mention is missing after the deployed installation. However this does not work. Switching off display in a browser - Seems to defeat the object of fixing the problem Removing old versions - There arent any. Trying with a different user - This affects all users of all privalige levels on all computers. On my workstation I uninstalled Acrobat Reader 9.1 then reinstalled manually using the same installation source files and it works fine. has anyone sucsessfully deployed AR9.1 on their domain and if so how? For the time being I have downloaded the older 8.1.3 release and deployed this in the same way which works fine, but would like to be using the up to date version. Thanks

  Read the article

• Why am I seeing Zero errors in non-ECC RAM?

  - by Alexander Shcheblikin

  According to sources, memory errors are a very probable event: Some say the probability of a DRAM error is 95% in just 3 days of operation of a computer with just 4 GB of RAM, others say 32% of servers experience at least one error in a month with 8% of DIMMs being at fault. Contrary to those horrors, in my more than 10 years of personal computers use I have seen exactly none of the memory errors. I admit I never paid special attention to the subject. However, I have ventured multi-hour memtest86 runs couple of times and never seen an error either. Some of the factors that IMO should aggravate the memory problems: I build my computers out of the most "bulk commodity" parts: mainstream budget motherboards and the next to cheapest memory. also I usually max out the technology available, e.g. in the times of 32 bit OS'es I used 4 GB of RAM and with the current desktop CPUs and the newer 64 bit OS'es I use 32 GB of RAM. memory usage is moderately heavy with lots of virtual machines up running small and big tasks 24/7/365. But nevertheless, no memory-related problems ever found! How's that?

  Read the article

• Print from Linux to Windows networked printer

  - by wonkothenoob

  I want to print from a Debian (Lenny) workstation to a Windows networked printer. I'm not even sure what type of Windows network this is. Our tech-support is friendly but doesn't want to get involved with supporting Linux. I need to use it for a variety of reasons and am completely stumped because I know nothing about Windows networking. They gave me URI smb://msprint.ourorg.edu as the "address" of the printer and further confirmed that the domain is "OURORG" and the share is "PHYS-PRI". I've installed CUPS and made sure that it's running as a daemon, I've clicked on the system-config-printer[1] icon, selected the printer as a Windows printer shared via SAMBA and entered the above URI. Attempting to print a testpage just sees it sit in the queue. I attempted to see if I could access the share using two other methods. Method 1. First I tried the "smbclient" from the CLI: $ smbclient -L //msprint.ourorg.edu -U user23 timeout connecting to 192.168.44.3:445 timeout connecting to 192.168.44.3:139 Connection to msprint.ourorg.edu failed (Error NT_STATUS_ACCESS_DENIED) Method 2. I tried to use the GUI tool Smb4K. This shows me four other toplevel (I'm assuming they're domains?) groupings one of which is the one which our IT department supplied to me. Clicking them shows a bunch of other machines with (what I assume are NetBIOS names?) including my own. I see all sorts of other networked printers belonging to other departments but none within mine. Certainly not the PHYS-PRI one suggested to me by the IT folks. I realize that I'm probably using the wrong terminology for the windows network, but can anyone help me with this? What steps should I be taking in debugging this? Do I need to actually run my machine as a SAMBA server to authenticate to the printer or should I just be able to communicate using CUPS? It's a GUI to CUPS configuration http://cyberelk.net/tim/software/system-config-printer/

  Read the article

• Could not find codec parameters in ffmpeg in Windows

  - by Grienders

  While trying to convert wmv to animated gif using ffmpeg in Windows 7, I ran into an issue. Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:\>ffmpeg -i test.wmv test.gif ffmpeg version N-39877-g4fa706a Copyright (c) 2000-2012 the FFmpeg developers built on Apr 16 2012 14:57:12 with gcc 4.6.3 configuration: --enable-gpl --enable-version3 --disable-w32threads --enable-ru ntime-cpudetect --enable-avisynth --enable-bzlib --enable-frei0r --enable-libass --enable-libcelt --enable-libopencore-amrnb --enable-libopencore-amrwb --enable -libfreetype --enable-libgsm --enable-libmp3lame --enable-libnut --enable-libope njpeg --enable-librtmp --enable-libschroedinger --enable-libspeex --enable-libth eora --enable-libutvideo --enable-libvo-aacenc --enable-libvo-amrwbenc --enable- libvorbis --enable-libvpx --enable-libx264 --enable-libxavs --enable-libxvid --e nable-zlib libavutil 51. 46.100 / 51. 46.100 libavcodec 54. 14.101 / 54. 14.101 libavformat 54. 3.100 / 54. 3.100 libavdevice 53. 4.100 / 53. 4.100 libavfilter 2. 70.100 / 2. 70.100 libswscale 2. 1.100 / 2. 1.100 libswresample 0. 11.100 / 0. 11.100 libpostproc 52. 0.100 / 52. 0.100 [asf @ 0000000001f3ead0] Could not find codec parameters (Video: none (MTS2 / 0x 3253544D), 800x400, 30000 kb/s) test.wmv: could not find codec parameters What does this mean and how can I solve it?

  Read the article

• PC -> TV HDMI suddenly doesn't work, any other option does

  - by XSlicer

  So my parents wanted to connect their PC to their TV, so they bought a 10m (35 ft) cable. It all worked perfectly. Then my mom tripped over the cable, breaking it. She somehow got a free replacement, but at the same time some more expensive one from an uncle. Now the problem is that this suddenly doesn't work anymore (TV saying "Format not supported"). I've tried several other things to pinpoint the actual problem, but none brought me something conslusive: PC (hdmi) to TV doesn't work (both cables) PC (hdmi) to TV doesn't work (short cable) Laptop (hdmi) to TV work (same cables) BluRay (hdmi) to TV works (same cables) PC (hdmi) to monitor works (same cables) PC (DVI w/ adapter HDMI) to TV works (same cables) I've tried different ports, tried Linux, reinstalling drivers (the graphics card is internal using an i5 sandy bridge. Normally it's running Windows 7 Home Prem, the TV being a Philips 37PFL7605H). So basically, everything works, except that thing what we want. The only things I am thinking of is that the sound is interfering or that the HDMI-output is somehow broken. Or is it anything else? I'm kind of lost.

  Read the article

• Corrupted NTFS Drive showing multiple unallocated partitions

  - by volting

  My external hdd with a single NTFS partition was accidentaly plugged out (kids!)... and is now corrupted. Iv tried running ntfsfix - with no luck - output below.. When I look at the disk under disk management in Windows 7 it shows up as having 5 partitions 2 of which are unallocated - none have drive letters and it is not possible to set any (that option and most others are greyed out) - so I can't run chkdsk /f Iv tried using Minitool partition wizard which was mentioned as a solution to another similar question here. It showed the whole drive as one partition, but as unallocated, and the option -- "Check File System" was greyout. Is there anything else I could try ? Output of fdisk -l Disk /dev/sdb: 1500.3 GB, 1500299395072 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930272256 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytest I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x69205244 This doesn't look like a partition table Probably you selected the wrong device. Device Boot Start End Blocks Id System /dev/sdb1 ? 218129509 1920119918 850995205 72 Unknown /dev/sdb2 ? 729050177 1273024900 271987362 74 Unknown /dev/sdb3 ? 168653938 168653938 0 65 Novell Netware 386 /dev/sdb4 2692939776 2692991410 25817+ 0 Empty Partition table entries are not in disk order Output of ntfsfix me@vaio:/dev$ sudo ntfsfix /dev/sdb Mounting volume... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error FAILED Attempting to correct errors... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error FAILED Failed to startup volume: Input/output error Checking for self-located MFT segment... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument OK ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error Volume is corrupt. You should run chkdsk. Options available with MiniTool: Related questions: How to fix a damaged/corrupted NTFS filesystem/partition without losing the data on it? Repair corrupted NTFS File System

  Read the article

• Remove directory from URL IIS 7.5

  - by xalx

  I've tried to find a solution to this and found some guides out there but none seem to work. I have the following URL - http://www.mysite.com/aboutus.html However there are some other sites which link to my old hosted site and point to http://www.mysite.com/nw/aboutus.html. My issue here is trying to remove the 'nw' directory from the URL's. I have setup the following URL Rewrite in IIS but it does not seem to do anything, <?xml version="1.0" encoding="UTF-8"?> <configuration> <system.webServer> <rewrite> <rules> <rule name="Redirect all to root folder" enabled="true" stopProcessing="true"> <match url="^nw$|^/nw/(.*)$" /> <conditions> </conditions> <action type="Redirect" url="nw/{R:1}" /> </rule> <rule name="RewriteToFile"> <match url="^(?!nw/)(.*)" /> <conditions> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> </conditions> <action type="Rewrite" url="/{R:1}" /> </rule> </rules> </rewrite> </system.webServer> </configuration> Any insight would be appreciated.

  Read the article

< Previous Page | 292 293 294 295 296 297 298 299 300 301 302 303  | Next Page >